@oimlsmart/primmel-packages 0.1.0

package/oiml-r129/specification/requirements/electronic.prl

@@ -0,0 +1,46 @@
+requirement_class /req/electronic {
+  title "Influence factor and disturbance requirements"
+  name "Environmental and electromagnetic requirements"
+  description "Requirements for influence factors (temperature, humidity, voltage), disturbances (EMC), and light/acoustic effects that electronic multi-dimensional measuring instruments shall withstand."
+  subject "environmental performance"
+  dependencies { /req/metrological/mpe }
+}
+
+requirement /req/electronic/rated-operating-conditions {
+  name "Rated operating conditions"
+  statement "Instruments shall not exceed the mpe when exposed to: (a) mains voltage -15 % to +10 % of nominal; (b) air temperature at stated limits or -10 °C to +40 °C if not stated; (c) 85 % relative humidity at the high temperature limit or 40 °C, whichever is lower. Special temperature limits shall span at least 30 °C."
+  binds_to { model.parameters.nominal_voltage family.parameters.temperature_min family.parameters.temperature_max }
+  applicability {
+    power_supply: [ac-mains, battery, dc]
+  }
+  verification { method testing description "Verified by influence factor tests (A.2.1–A.2.4)." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.2.1"
+}
+
+requirement /req/electronic/disturbance-resistance {
+  name "Disturbance resistance"
+  statement "When exposed to disturbances, either significant faults do not occur, or significant faults are detected and acted upon. A fault ≤ d is allowed during the disturbance."
+  verification { method testing description "Verified by disturbance tests (A.3.1–A.3.5)." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.3.1"
+}
+
+requirement /req/electronic/no-significant-faults {
+  name "No significant faults during disturbances"
+  statement "If the instrument does not detect and react to a significant fault, then the fault shall not exceed the value of one scale interval (d)."
+  applicability {
+    power_supply: [ac-mains, battery, dc]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.3.1"
+}
+
+requirement /req/electronic/light-acoustic-effects {
+  name "Light and acoustic effects"
+  statement "Instruments based on light or acoustic measuring techniques shall remain within the mpe when subjected to the applicable light or acoustic effects, or have provisions for alternative operations if the instrument can only perform across a limited range."
+  applicability {
+    measurement_principle: [optical, acoustic]
+  }
+  verification { method testing description "Verified by ambient light test (A.4.1) for optical instruments, acoustics test (A.4.2) for acoustic instruments." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.4"
+}
+

package/oiml-r129/specification/requirements/metrological.prl

@@ -0,0 +1,83 @@
+requirement_class /req/metrological {
+  title "Metrological requirements"
+  name "Metrological requirements for multi-dimensional measuring instruments"
+  description "Requirements for maximum permissible errors, scale intervals, minimum dimensions, fault limits, indicator variation, multi-interval instruments, and calculated quantities applicable to all multi-dimensional measuring instruments."
+  subject "dimensional measurement metrology"
+}
+
+requirement /req/metrological/scale-intervals-min-dimension {
+  name "Scale intervals and minimum dimension"
+  statement "The lower limit of the minimum dimension for all values of the scale interval shall be as follows: for d ≤ 2 cm, Min ≥ 10 d; for 2 cm < d ≤ 10 cm, Min ≥ 20 d; for d > 10 cm, Min ≥ 50 d."
+  binds_to { model.parameters.scale_interval model.parameters.min_dimension }
+  parameters {
+    param d: number { description "Scale interval value" unit "cm" bind "model.parameters.scale_interval" }
+  }
+  verification { method inspection description "Verify minimum dimension marking on instrument nameplate matches scale interval." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.1"
+}
+
+requirement /req/metrological/mpe {
+  name "Value of the maximum permissible error"
+  statement "The mpe applicable to the measurement by the instrument of any of the three dimensions for initial and subsequent verification is ±1.0 d."
+  binds_to { model.parameters.scale_interval }
+  limit {
+    quantity { kind length unit "cm" }
+    accepts {
+      verdict error_of_indication
+      op lte
+      limit "ocl{1.0 * d}"
+    }
+    uses { observable:indication observable:reference_dimension model.parameters.scale_interval formula:lookupMPE }
+  }
+  acceptance_criteria {
+    type: "threshold"
+    description: "Error of indication shall not exceed ±1.0 d"
+    limit:
+      expression: "error_of_indication"
+      operator: "abs_lte"
+      threshold_expression: "1.0 * d"
+      unit: "d"
+  }
+  verification { method testing description "Verified by applying known test objects and comparing indications to reference dimensions." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.2"
+}
+
+requirement /req/metrological/fault-limit {
+  name "Value of the fault limit"
+  statement "The value of the fault limit is one scale interval (d). A fault equal to or smaller than d is allowed during a disturbance irrespective of the value of the error of indication prior to the disturbance."
+  verification { method testing description "Verified during disturbance tests by comparing indications with and without disturbance." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.3"
+}
+
+requirement /req/metrological/variation-between-indicators {
+  name "Maximum permissible variation between indicators"
+  statement "There shall be no difference between the indications when displayed on different digital indicators."
+  verification { method inspection description "Compare indications on all installed digital indicators during testing." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.4"
+}
+
+requirement /req/metrological/multi-interval {
+  name "Multi-interval instruments"
+  statement "For multi-interval instruments with scale intervals of d₁, d₂, …, dᵣ, the mpe are ±1 d₁, ±1 d₂, …, ±1 dᵣ for the applicable range and axis."
+  verification { method testing description "Verify mpe for each partial measuring range with appropriate test objects." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.5"
+}
+
+requirement /req/metrological/calculated-quantities {
+  name "Calculated quantities"
+  statement "All calculated quantities included in the transaction shall be derived from the indicated measured dimensions, which are rounded to the nearest applicable scale interval. All calculated quantities shall be in mathematical agreement."
+  verification { method inspection description "Verify that displayed/printed calculated volume and weight match L × W × H." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.6"
+}
+
+requirement /req/metrological/error-determination-rules {
+  name "Rules for the determination of errors"
+  statement "The specifications in 4.1.2 to 4.1.5 apply to all instruments irrespective of their principles of operation. The initial intrinsic error is found at reference conditions of 20 °C ± 5 °C, ambient atmospheric pressure, nominal voltage and (50 ± 15) % relative humidity. For instruments with an extended indication device displaying ≤ d/5, the error of indication = Indication − Known dimensions. Otherwise, error of indication = Indication − Nominal dimensions."
+  parameters {
+    param reference_temperature: number { description "Reference temperature" unit "°C" default 20 }
+    param reference_humidity: number { description "Reference relative humidity" unit "%" default 50 }
+  }
+  verification { method definitional description "Reference conditions must be maintained during initial intrinsic error determination." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.7"
+}
+

package/oiml-r129/specification/requirements/object-limitations.prl

@@ -0,0 +1,99 @@
+requirement_class /req/object-limitations {
+  title "Object limitation requirements"
+  name "Requirements for measurement of various object types"
+  description "Requirements relating to the ability of the instrument to measure objects of varying shape, surface characteristics, orientation, and relative motion speed. Based on R 129-1, Annex A (normative guidelines)."
+  subject "object characteristics"
+  guidance "R 129-1 Annex A provides informative guidelines on known limitations. Instruments must be marked with any limitations of use."
+  dependencies { /req/metrological/mpe }
+}
+
+requirement /req/object-limitations/object-shape {
+  name "Shape of the object"
+  statement "Instruments that can only measure rectangular boxes shall be so marked. If an instrument can measure irregular shapes in some but not all dimensions, it shall be marked that it is only to be used for measuring rectangular boxes."
+  applicability {
+    measurement_principle: [mechanical, optical, acoustic]
+  }
+  verification { method testing description "Test with irregular-shaped objects to verify measurement capability." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.2"
+}
+
+requirement /req/object-limitations/surface-colour-uniform {
+  name "Surface colour — uniform"
+  statement "Light coloured objects are more easily measured than dark coloured objects for instruments using light. Suitable test objects with surfaces varying from shiny white to matt black shall be used to determine limits."
+  applicability {
+    measurement_principle: [optical]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.1"
+}
+
+requirement /req/object-limitations/surface-colour-non-uniform {
+  name "Surface colour — non-uniform"
+  statement "Instruments shall correctly measure objects with non-uniform surface colour within marked limitations."
+  applicability {
+    measurement_principle: [optical]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.2"
+}
+
+requirement /req/object-limitations/surface-reflectivity {
+  name "Surface reflectivity and absorption"
+  statement "For acoustic instruments, sound reflective qualities depend on density and smoothness. For optical instruments, light reflective qualities depend on surface finish. Instruments shall correctly measure objects with varying surface characteristics within marked limitations."
+  applicability {
+    measurement_principle: [optical, acoustic]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.4"
+}
+
+requirement /req/object-limitations/transparency {
+  name "Transparency"
+  statement "Instruments using light beam cutting or reflection shall correctly handle transparent or semi-transparent objects within marked limitations."
+  applicability {
+    measurement_principle: [optical]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.7"
+}
+
+requirement /req/object-limitations/surface-roughness {
+  name "Surface roughness"
+  statement "Instruments shall correctly measure objects with varying surface roughness within marked limitations."
+  applicability {
+    measurement_principle: [mechanical, optical, acoustic]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.8"
+}
+
+requirement /req/object-limitations/surface-protrusions {
+  name "Protrusions on the surface"
+  statement "Instruments shall correctly measure objects with protrusions within marked limitations. If a minimum protrusion is marked, a test object with that size protrusion shall be used."
+  applicability {
+    measurement_principle: [mechanical, optical, acoustic]
+  }
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.3.9"
+}
+
+requirement /req/object-limitations/orientation-position {
+  name "Orientation and position"
+  statement "If the instrument does not depend on a particular orientation or position, several different orientations and positions shall be tested and the results shall be within mpe."
+  applicability {
+    measurement_principle: [mechanical, optical, acoustic]
+  }
+  verification { method testing description "Test objects placed in various orientations and positions on the measuring plane." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-A.4"
+}
+
+requirement /req/object-limitations/speed-movement {
+  name "Speed of relative movement"
+  statement "For automatic instruments with relative movement between object and instrument, measurements at maximum and minimum speeds shall be within mpe."
+  applicability {
+    instrument_category: [automatic]
+  }
+  verification { method testing description "Test at V_min and V_max with appropriate test objects." }
+  ref derives-from "urn:oiml:pub:r:129-2:2020#clause-A"
+}
+

package/oiml-r129/specification/requirements/software.prl

@@ -0,0 +1,57 @@
+requirement_class /req/software {
+  title "Software requirements"
+  name "Software requirements for multi-dimensional measuring instruments"
+  description "Requirements for software identification, algorithm correctness, securing and protection of legally relevant software, authentication, audit trail, specific configurations, detection of significant defects, and durability protection."
+  subject "instrument software"
+  dependencies { /req/technical/sealing }
+}
+
+requirement /req/software/software-identification {
+  name "Software identification"
+  statement "The software of a measuring instrument shall be clearly identified. The identification shall be displayed on command, during operation, or on start-up. If a software-controlled component has no display, the identification shall be sent via a communication interface. If the software is modified in any way, a new identification is required."
+  verification { method inspection description "Verify software identification is accessible and displayed." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.1"
+}
+
+requirement /req/software/algorithm-correctness {
+  name "Correctness of algorithms and functions"
+  statement "The measuring algorithms and functions shall be appropriate and functionally correct for the given application. It shall be possible to assess algorithms and functions either by metrological tests, software tests or software examination. No hidden or undocumented functions or parameters shall exist."
+  verification { method testing description "Functional testing of measurement algorithms and calculations." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.2"
+}
+
+requirement /req/software/securing-software {
+  name "Securing and protecting software"
+  statement "Software-controlled instruments shall minimize possibilities for unintentional, unauthorised, or intentional misuse. Software shall be protected so that evidence of any intervention is available. Parameters that fix the legally relevant characteristics shall be protected. Displaying or printing of current legally relevant parameter settings shall be possible."
+  verification { method inspection description "Examine software protection mechanisms and parameter security." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.3"
+}
+
+requirement /req/software/authentication-results {
+  name "Authentication of measurement results"
+  statement "It shall not be possible to fraudulently simulate legally relevant software for presenting measurement results, using easily available and manageable tools."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.4"
+}
+
+requirement /req/software/audit-trail {
+  name "Audit trail"
+  statement "Audit trails shall be protected, non-deletable, and non-exchangeable. They shall contain success/failure of updates, timestamps, software identification, and parameter change details. Storage shall suffice for at least three successive verifications."
+  verification { method inspection description "Verify audit trail content and protection." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.5"
+}
+
+requirement /req/software/significant-defect-detection {
+  name "Detection of significant defects"
+  statement "If software is involved in detecting significant defects, the instrument shall be made inoperative automatically or provide a visual/audible indication that continues until the user takes action."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.7"
+}
+
+requirement /req/software/durability-protection {
+  name "Durability protection support"
+  statement "If software is involved in durability protection, the instrument shall initiate measures to ensure further durability, become inoperable, or the problem shall disappear on its own."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-6.8"
+}
+

package/oiml-r129/specification/requirements/technical.prl

@@ -0,0 +1,134 @@
+requirement_class /req/technical {
+  title "Technical requirements"
+  name "Technical requirements for multi-dimensional measuring instruments"
+  description "Requirements for construction, indicators, markings, sealing, interfaces, and checking facilities applicable to all multi-dimensional measuring instruments."
+  subject "instrument construction and operation"
+  dependencies { /req/metrological }
+}
+
+requirement /req/technical/fraudulent-use {
+  name "Fraudulent use prevention"
+  statement "Instruments shall not facilitate fraudulent use, either by accidental or by deliberate means when using the instrument in the normal manner."
+  verification { method inspection description "Visual and functional examination of the instrument design." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.1"
+}
+
+requirement /req/technical/suitability-construction {
+  name "Suitability of construction"
+  statement "Instruments shall be of adequately robust construction to maintain their metrological characteristics when properly installed and used in an environment for which they are intended. Instruments shall be constructed so that all controls, indicators, etc. are suitable for operation under normal conditions of use."
+  verification { method inspection description "Examine construction quality, materials, and durability." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.2"
+}
+
+requirement /req/technical/suitability-use {
+  name "Suitability for use"
+  statement "Instruments shall be designed to suit the method of operation and the objects for which they are intended."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.3"
+}
+
+requirement /req/technical/suitability-verification {
+  name "Suitability for verification"
+  statement "Instruments shall be constructed so that the performance requirements of this Recommendation can be applied. If in normal operation the instrument indicates the volume and not the measured dimensions, a test mode shall be provided to display or print out the measured dimensions."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.4"
+}
+
+requirement /req/technical/zero-ready-adjustment {
+  name "Zero or ready adjustment"
+  statement "Instruments shall be provided with facilities to set the instrument to, and maintain it at, zero or ready condition. This shall only be possible without an object in the measuring area. Either this condition is met automatically for each measurement or the instrument is automatically inhibited from making measurements."
+  verification { method testing description "Verify zero/ready condition cannot be set with object present." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.5"
+}
+
+requirement /req/technical/tare-device {
+  name "Tare device"
+  statement "The tare function shall only operate subtractively. The value of the tare scale interval shall be the same as the scale interval of the respective axis and range. Operation of tare shall be indicated."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.6"
+}
+
+requirement /req/technical/warm-up {
+  name "Warm-up period"
+  statement "As soon as the instrument indicates, prints, stores or transmits the measurement results after the warm-up period following switch-on, the indications shall be within mpe."
+  verification { method testing description "Test at 0, 5, 15 and 30 minutes after switch-on." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.1.7"
+}
+
+requirement /req/technical/presentation-indications {
+  name "Presentation of indications"
+  statement "Printed and displayed indications shall be reliable, clear and unambiguous and printing shall be indelible. Figures forming the results shall be of a size, shape and clarity for reading to be easy. Printed numbers and symbols shall be at least 2 mm high."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.2.2"
+}
+
+requirement /req/technical/units-of-measurement {
+  name "Units of measurement"
+  statement "All printed and displayed indications shall include the name or symbol of the unit of measurement. For each indication of a quantity only one unit of measurement for that quantity shall be used, and the unit of measurement shall be the same for each axis."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.2.3"
+}
+
+requirement /req/technical/scale-interval-value {
+  name "Value of the scale interval"
+  statement "The value of all scale intervals shall be in the form 1, 2 or 5 × 10ⁿ where n is a positive or negative whole number or zero."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.2.4"
+}
+
+requirement /req/technical/limits-of-indication {
+  name "Limits of indication"
+  statement "Displaying, storing, transmitting or printing the quantity value of any dimension shall either be inhibited or an error message shall be included if the axis is shorter than Min or longer than Max + 9 d. Measurement shall be inhibited if the entire object is not contained within the measuring area."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.2.6"
+}
+
+requirement /req/technical/nameplate-markings {
+  name "Nameplate markings"
+  statement "Instruments shall be clearly and permanently marked with: manufacturer's name or mark; model designation; serial number and year of manufacture; type evaluation mark; Max and Min for each axis; V_max and V_min if applicable; scale interval(s) for each axis; and temperature limits if other than -10 °C to +40 °C."
+  verification { method inspection description "Visual examination of nameplate and markings." }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.3.1"
+}
+
+requirement /req/technical/technical-specifications {
+  name "Technical specifications display"
+  statement "Any specifications or limitation of use relating to the instrument or the objects being measured shall be visibly and clearly presented to the operator on the instrument."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.3.2"
+}
+
+requirement /req/technical/verification-mark {
+  name "Verification mark provision"
+  statement "Provision shall be made for the application of a verification mark on a nameplate, stamping plug or adhesive label. The mark shall be easily affixed, visible when in use, not removable without damage, and have at least 200 mm² of space."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.4.1"
+}
+
+requirement /req/technical/sealing {
+  name "Sealing provisions"
+  statement "Provision shall be made for sealing devices, software and parameters that have a metrologically significant effect. Sealing may be by mechanical, electronic, software (audit trail) and/or cryptographic means."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.4.2"
+}
+
+requirement /req/technical/interfaces {
+  name "Interfaces for peripheral devices"
+  statement "An instrument may be equipped with interfaces permitting the coupling of peripheral devices or other instruments. The interface shall not allow metrological functions or measurement data to be affected."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.5.2"
+}
+
+requirement /req/technical/checking-significant-faults {
+  name "Acting upon significant faults"
+  statement "When a significant fault has been detected, the instrument shall either be made inoperative automatically or a visual or audible indication shall be provided automatically and shall continue until the user takes action or the fault disappears. For automatic instruments, the instrument shall be made inoperative automatically."
+  verification { method testing }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.6.1"
+}
+
+requirement /req/technical/indication-check {
+  name "Indication check"
+  statement "If the failure of an indicator display element can cause a false indication, then the instrument shall have a display test facility which shows all relevant elements in both active and non-active states."
+  verification { method inspection }
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-5.6.2"
+}
+

package/oiml-r129/specification/symbols.prl

@@ -0,0 +1,187 @@
+symbol d {
+  name "Scale interval"
+  definition "scale interval of the instrument for a dimension; form 1, 2 or 5 × 10ⁿ (R 129-1, 5.2.4)"
+  type number
+  unit "cm"
+  latex "d"
+  kind attribute
+  quantity_kind length
+  origin declared
+  attribute scale_interval
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.9"
+}
+
+symbol max_dimension {
+  name "Maximum dimension"
+  definition "largest value of a dimension that can be measured"
+  type number
+  unit "cm"
+  latex "Max"
+  kind attribute
+  quantity_kind length
+  origin declared
+  attribute max_dimension
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.5"
+}
+
+symbol min_dimension {
+  name "Minimum dimension"
+  definition "smallest value of a dimension that can be measured; related to d per R 129-1, Table 2"
+  type number
+  unit "cm"
+  latex "Min"
+  kind attribute
+  quantity_kind length
+  origin declared
+  attribute min_dimension
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.6"
+}
+
+symbol conversion_factor {
+  name "Conversion factor"
+  definition "coefficient that, applied to the dimensional volume, gives the dimensional weight"
+  type number
+  unit "cm3/kg"
+  latex "F"
+  kind attribute
+  quantity_kind volume-per-mass
+  origin declared
+  attribute conversion_factor
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.8"
+}
+
+symbol speed_max {
+  name "Maximum measuring speed"
+  definition "maximum speed of relative movement for which the instrument maintains its metrological properties"
+  type number
+  unit "m/s"
+  latex "V_max"
+  kind attribute
+  quantity_kind speed
+  origin declared
+  attribute speed_max
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.1.10"
+}
+
+symbol speed_min {
+  name "Minimum measuring speed"
+  definition "minimum speed of relative movement for which the instrument maintains its metrological properties"
+  type number
+  unit "m/s"
+  latex "V_min"
+  kind attribute
+  quantity_kind speed
+  origin declared
+  attribute speed_min
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.1.11"
+}
+
+symbol mpe {
+  name "Maximum permissible error"
+  definition "maximum permissible error of the indication: ±1.0 d for any of the three dimensions"
+  type number
+  unit "d"
+  latex "MPE"
+  kind formula
+  quantity_kind length
+  origin lookup
+  calculation lookupMPE
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.2"
+  formula {
+    display "MPE = ±1.0 d"
+    expression "1.0 * d"
+    inputs { d }
+  }
+}
+
+symbol dimensional_volume {
+  name "Dimensional volume"
+  definition "volume of the smallest enclosing rectangular box: DV = L × W × H"
+  type number
+  unit "cm3"
+  latex "DV"
+  kind formula
+  quantity_kind volume
+  origin derived
+  calculation dimensionalVolume
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.4"
+  formula {
+    display "DV = L × W × H"
+    expression "indication_l * indication_w * indication_h"
+    inputs { indication_l indication_w indication_h }
+  }
+}
+
+symbol dimensional_weight {
+  name "Dimensional weight"
+  definition "weight equivalent of the dimensional volume: DW = DV / F"
+  type number
+  unit "kg"
+  latex "DW"
+  kind formula
+  quantity_kind mass
+  origin derived
+  calculation dimensionalWeight
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.2.7"
+  formula {
+    display "DW = DV / F"
+    expression "dimensional_volume / conversion_factor"
+    inputs { dimensional_volume conversion_factor }
+  }
+}
+
+symbol fault_limit {
+  name "Significant fault threshold"
+  definition "a fault exceeding 1 d is a significant fault (R 129-1, 4.1.3, 2.3.6)"
+  type number
+  unit "d"
+  latex "SF"
+  kind formula
+  quantity_kind length
+  origin lookup
+  calculation lookupMPE
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.3"
+  formula {
+    display "SF = 1.0 d"
+    expression "1.0 * d"
+    inputs { d }
+  }
+}
+
+symbol indication {
+  name "Indication of a dimension"
+  definition "indicated value of a measured dimension (any axis)"
+  type number
+  unit "cm"
+  latex "I"
+  kind observable
+  quantity_kind length
+  origin measured
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.1.12"
+}
+
+symbol reference_dimension {
+  name "Reference dimension"
+  definition "known (true) dimension of the test object used as reference"
+  type number
+  unit "cm"
+  latex "D_ref"
+  kind observable
+  quantity_kind length
+  origin measured
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.1.7"
+}
+
+symbol error_of_indication {
+  name "Error of indication"
+  definition "indication minus the reference dimension (VIML 0.04)"
+  type number
+  unit "cm"
+  latex "E"
+  kind observable
+  quantity_kind length
+  origin derived
+  calculation measurementError
+  ref derives-from "urn:oiml:pub:r:129-1:2020#clause-2.3.1"
+}
+