meerk40t 0.9.3001__py2.py3-none-any.whl → 0.9.7010__py2.py3-none-any.whl

meerk40t/lihuiyu/controller.py

@@ -1,876 +1,883 @@
-"""
-Lihuiyu Controller
-
-Deals with the sending of data via the registered connection, and processes some limited realtime commands.
-
-    - : require wait finish at the end of the queue processing.
-    * : clear the buffers, and abort the thread.
-    ! : pause.
-    & : resume.
-    % : fail checksum, do not resend
-    ~ : begin/end realtime exception (Note, these characters would be consumed during
-            the write process and should not exist in the queue)
-    \x18 : quit.
-
-"""
-
-import threading
-import time
-
-from meerk40t.ch341 import get_ch341_interface
-
-STATUS_SERIAL_CORRECT_M3_FINISH = 204
-# 0xCC, 11001100
-STATUS_OK = 206
-# 0xCE, 11001110
-STATUS_ERROR = 207
-# 0xCF, 11001111
-STATUS_FINISH = 236
-# 0xEC, 11101100
-STATUS_BUSY = 238
-# 0xEE, 11101110
-STATUS_POWER = 239
-
-
-STATE_X_FORWARD_LEFT = (
-    0b0000000000000001  # Direction is flagged left rather than right.
-)
-STATE_Y_FORWARD_TOP = 0b0000000000000010  # Direction is flagged top rather than bottom.
-STATE_X_STEPPER_ENABLE = 0b0000000000000100  # X-stepper motor is engaged.
-STATE_Y_STEPPER_ENABLE = 0b0000000000001000  # Y-stepper motor is engaged.
-STATE_HORIZONTAL_MAJOR = 0b0000000000010000
-REQUEST_X = 0b0000000000100000
-REQUEST_X_FORWARD_LEFT = 0b0000000001000000  # Requested direction towards the left.
-REQUEST_Y = 0b0000000010000000
-REQUEST_Y_FORWARD_TOP = 0b0000000100000000  # Requested direction towards the top.
-REQUEST_AXIS = 0b0000001000000000
-REQUEST_HORIZONTAL_MAJOR = 0b0000010000000000  # Requested horizontal major axis.
-
-
-def get_code_string_from_code(code):
-    if code == STATUS_OK:
-        return "OK"
-    elif code == STATUS_BUSY:
-        return "Busy"
-    elif code == STATUS_ERROR:
-        return "Rejected"
-    elif code == STATUS_FINISH:
-        return "Finish"
-    elif code == STATUS_POWER:
-        return "Low Power"
-    elif code == STATUS_SERIAL_CORRECT_M3_FINISH:
-        return "M3-Finished"
-    elif code == 0:
-        return "USB Failed"
-    else:
-        return f"UNK {code:02x}"
-
-
-def convert_to_list_bytes(data):
-    if isinstance(data, str):  # python 2
-        packet = [0] * 30
-        for i in range(0, 30):
-            packet[i] = ord(data[i])
-        return packet
-    else:
-        packet = [0] * 30
-        for i in range(0, 30):
-            packet[i] = data[i]
-        return packet
-
-
-crc_table = [
-    0x00,
-    0x5E,
-    0xBC,
-    0xE2,
-    0x61,
-    0x3F,
-    0xDD,
-    0x83,
-    0xC2,
-    0x9C,
-    0x7E,
-    0x20,
-    0xA3,
-    0xFD,
-    0x1F,
-    0x41,
-    0x00,
-    0x9D,
-    0x23,
-    0xBE,
-    0x46,
-    0xDB,
-    0x65,
-    0xF8,
-    0x8C,
-    0x11,
-    0xAF,
-    0x32,
-    0xCA,
-    0x57,
-    0xE9,
-    0x74,
-]
-
-
-def onewire_crc_lookup(line):
-    """
-    License: 2-clause "simplified" BSD license
-    Copyright (C) 1992-2017 Arjen Lentz
-    https://lentz.com.au/blog/calculating-crc-with-a-tiny-32-entry-lookup-table
-
-    @param line: line to be CRC'd
-    @return: 8 bit crc of line.
-    """
-    crc = 0
-    for i in range(0, 30):
-        crc = line[i] ^ crc
-        crc = crc_table[crc & 0x0F] ^ crc_table[16 + ((crc >> 4) & 0x0F)]
-    return crc
-
-
-class LihuiyuController:
-    """
-    K40 Controller controls the Lihuiyu boards sending any queued data to the USB when the signal is not busy.
-
-    Opening and closing of the pipe are dealt with internally. There are three primary monitor data channels.
-    'send', 'recv' and 'usb'. They display the reading and writing of information to/from the USB and the USB connection
-    log, providing information about the connecting and error status of the USB device.
-    """
-
-    def __init__(self, context, *args, **kwargs):
-        self.context = context
-        self.state = "unknown"
-        self.is_shutdown = False
-        self.serial_confirmed = None
-
-        self._thread = None
-        self._buffer = (
-            bytearray()
-        )  # Threadsafe buffered commands to be sent to controller.
-        self._realtime_buffer = (
-            bytearray()  # Threadsafe realtime buffered commands to be sent to the controller.
-        )
-        self._queue = bytearray()  # Thread-unsafe additional commands to append.
-        self._preempt = (
-            bytearray()
-        )  # Thread-unsafe preempt commands to prepend to the buffer.
-        self._queue_lock = threading.Lock()
-        self._preempt_lock = threading.Lock()
-        self._main_lock = threading.Lock()
-        self._connect_lock = threading.RLock()
-        self._loop_cond = threading.Condition()
-
-        self._status = [0] * 6
-        self._usb_state = -1
-
-        self.connection = None
-        self.max_attempts = 5
-        self.refuse_counts = 0
-        self.connection_errors = 0
-        self.aborted_retries = False
-        self.pre_ok = False
-        self.realtime = False
-
-        self.abort_waiting = False
-
-        name = self.context.label
-        self.pipe_channel = context.channel(f"{name}/events")
-        self.usb_log = context.channel(f"{name}/usb", buffer_size=500)
-        self.usb_send_channel = context.channel(f"{name}/usb_send")
-        self.recv_channel = context.channel(f"{name}/recv")
-        self.usb_log.watch(lambda e: context.signal("pipe;usb_status", e))
-        self.reset()
-
-    @property
-    def viewbuffer(self):
-        buffer = bytes(self._realtime_buffer) + bytes(self._buffer) + bytes(self._queue)
-        try:
-            buffer_str = buffer.decode()
-        except ValueError:
-            try:
-                buffer_str = buffer.decode("utf8")
-            except UnicodeDecodeError:
-                buffer_str = str(buffer)
-        except AttributeError:
-            buffer_str = buffer
-        return buffer_str
-
-    def added(self):
-        self.start()
-
-    def service_detach(self):
-        pass
-
-    def shutdown(self, *args, **kwargs):
-        if self._thread is not None:
-            self.realtime_write(b"\x18\n")
-
-    def __repr__(self):
-        return f"LihuiyuController({str(self.context)})"
-
-    def __len__(self):
-        """Provides the length of the buffer of this device."""
-        return len(self._buffer) + len(self._queue) + len(self._preempt)
-
-    def open(self):
-        with self._connect_lock:
-            self._process_open()
-
-    def _process_open(self):
-        if self.connection is not None and self.connection.is_connected():
-            return  # Already connected.
-        _ = self.usb_log._
-        self.pipe_channel("open()")
-        try:
-            interfaces = list(
-                get_ch341_interface(
-                    self.context,
-                    self.usb_log,
-                    mock=self.context.mock,
-                    mock_status=STATUS_OK,
-                    bulk=True,
-                )
-            )
-            if self.context.usb_index != -1:
-                # Instructed to check one specific device.
-                devices = [self.context.usb_index]
-            else:
-                devices = range(16)
-
-            for interface in interfaces:
-                self.connection = interface
-                for i in devices:
-                    try:
-                        self._open_at_index(i)
-                        return  # Opened successfully.
-                    except ConnectionRefusedError as e:
-                        self.usb_log(str(e))
-                        if self.connection is not None:
-                            self.connection.close()
-                    except IndexError:
-                        self.usb_log(_("Connection failed."))
-                        self.connection = None
-                        break
-        except PermissionError as e:
-            self.usb_log(str(e))
-            return  # OS denied permissions, no point checking anything else.
-
-        self.close()
-        raise ConnectionRefusedError(
-            _("No valid connection matched any given criteria.")
-        )
-
-    def _open_at_index(self, usb_index):
-        _ = self.context.kernel.translation
-        self.connection.open(usb_index=usb_index)
-        if not self.connection.is_connected():
-            raise ConnectionRefusedError("ch341 connect did not return a connection.")
-        if self.context.usb_bus != -1 and self.connection.bus != -1:
-            if self.connection.bus != self.context.usb_bus:
-                raise ConnectionRefusedError(
-                    _("K40 devices were found but they were rejected due to usb bus.")
-                )
-        if self.context.usb_address != -1 and self.connection.address != -1:
-            if self.connection.address != self.context.usb_address:
-                raise ConnectionRefusedError(
-                    _(
-                        "K40 devices were found but they were rejected due to usb address."
-                    )
-                )
-        if self.context.usb_version != -1:
-            version = self.connection.get_chip_version()
-            if version != self.context.usb_version:
-                raise ConnectionRefusedError(
-                    _(
-                        "K40 devices were found but they were rejected due to chip version."
-                    )
-                )
-        if self.context.serial_enable and self.context.serial is not None:
-            if self.serial_confirmed:
-                return  # already passed.
-            self.usb_log(_("Requires serial number confirmation."))
-            self.challenge(self.context.serial)
-            t = time.time()
-            while time.time() - t < 0.5:
-                if self.serial_confirmed:
-                    break
-            if not self.serial_confirmed:
-                raise ConnectionRefusedError("Serial number confirmation failed.")
-            else:
-                self.usb_log(_("Serial number confirmed."))
-
-    def close(self):
-        self.pipe_channel("close()")
-        with self._connect_lock:
-            if self.connection is None:
-                return
-            self.connection.close()
-            self.connection = None
-
-    def write(self, bytes_to_write):
-        """
-        Writes data to the queue, this will be moved into the buffer by the thread in a threadsafe manner.
-
-        @param bytes_to_write: data to write to the queue.
-        @return:
-        """
-        f = bytes_to_write.find(b"~")
-        if f != -1:
-            # ~ was found in bytes. We are in a realtime exception.
-            self.realtime = True
-
-            # All code prior to ~ is sent to write.
-            queue_bytes = bytes_to_write[:f]
-            if queue_bytes:
-                self.write(queue_bytes)
-
-            # All code after ~ is sent to realtime write.
-            preempt_bytes = bytes_to_write[f + 1 :]
-            if preempt_bytes:
-                self.realtime_write(preempt_bytes)
-            return self
-        if self.realtime:
-            # We are in a realtime exception that has not been terminated.
-            self.realtime_write(bytes_to_write)
-            return self
-
-        self.pipe_channel(f"write({str(bytes_to_write)})")
-        with self._queue_lock:
-            self._queue += bytes_to_write
-        self.start()
-        self.update_buffer()
-        return self
-
-    def realtime_write(self, bytes_to_write):
-        """
-        Writes data to the preempting commands, this will be moved to the front of the buffer by the thread
-        in a threadsafe manner.
-
-        @param bytes_to_write: data to write to the front of the queue.
-        @return:
-        """
-        f = bytes_to_write.find(b"~")
-        if f != -1:
-            # ~ was found in bytes. We are leaving realtime exception.
-            self.realtime = False
-
-            # All date prior to the ~ is sent to realtime write.
-            preempt_bytes = bytes_to_write[:f]
-            if preempt_bytes:
-                self.realtime_write(preempt_bytes)
-
-            # All data after ~ is sent back to normal write.
-            queue_bytes = bytes_to_write[f + 1 :]
-            if queue_bytes:
-                self.write(queue_bytes)
-            return self
-        self.pipe_channel(f"realtime_write({str(bytes_to_write)})")
-        if b"*" in bytes_to_write:
-            self.abort_waiting = True
-        with self._preempt_lock:
-            self._preempt = bytearray(bytes_to_write) + self._preempt
-        self.start()
-        self.update_buffer()
-        return self
-
-    def start(self):
-        """
-        Controller state change to `Started`.
-        @return:
-        """
-        with self._loop_cond:
-            self._loop_cond.notify()
-        if not self.is_shutdown and (
-            self._thread is None or not self._thread.is_alive()
-        ):
-            self.update_state("init")
-            self._thread = self.context.threaded(
-                self._thread_data_send,
-                thread_name=f"LhyPipe({self.context.path})",
-                result=self.stop,
-            )
-            self._thread.stop = self.stop
-
-    def _pause_busy(self):
-        """
-        BUSY can be called in a paused state to packet halt the controller.
-
-        This can only be done from PAUSE.
-        """
-        if self.state != "pause":
-            self.pause()
-        if self.state == "pause":
-            self.update_state("busy")
-
-    def _resume_busy(self):
-        """
-        Resumes from a BUSY to restore the controller. This will return to a paused state.
-
-        This can only be done from BUSY.
-        """
-        if self.state == "busy":
-            self.update_state("pause")
-            self.resume()
-
-    def pause(self):
-        """
-        Pause simply holds the controller from sending any additional packets.
-
-        If this state change is done from INITIALIZE it will start the processing.
-        Otherwise, it must be done from ACTIVE or IDLE.
-        """
-        if self.state == "init":
-            self.start()
-            self.update_state("pause")
-        if self.state in ("active", "idle"):
-            self.update_state("pause")
-
-    def resume(self):
-        """
-        Resume can only be called from PAUSE.
-        """
-        if self.state == "pause":
-            self.update_state("active")
-
-    def abort(self):
-        self._buffer = bytearray()
-        self._queue = bytearray()
-        self._realtime_buffer = bytearray()
-        self.abort_waiting = False
-        self.context.signal("pipe;buffer", 0)
-        self.update_state("terminate")
-
-    def reset(self):
-        self.update_state("init")
-
-    def stop(self, *args):
-        self.abort()
-        try:
-            if self._thread is not None:
-                self._thread.join()  # Wait until stop completes before continuing.
-            self._thread = None
-        except RuntimeError:
-            pass  # Stop called by current thread.
-
-    def abort_retry(self):
-        with self._loop_cond:
-            self._loop_cond.notify()
-        self.aborted_retries = True
-        self.context.signal("pipe;state", "STATE_FAILED_SUSPENDED")
-
-    def continue_retry(self):
-        with self._loop_cond:
-            self._loop_cond.notify()
-        self.aborted_retries = False
-        self.context.signal("pipe;state", "STATE_FAILED_RETRYING")
-
-    def usb_release(self):
-        if self.connection:
-            self.connection.release()
-        else:
-            raise ConnectionError
-
-    def usb_reset(self):
-        if self.connection:
-            self.connection.reset()
-        else:
-            raise ConnectionError
-
-    def challenge(self, serial):
-        if serial is None:
-            return
-
-        from hashlib import md5
-
-        challenge = bytearray.fromhex(md5(bytes(serial.upper(), "utf8")).hexdigest())
-        packet = b"A%s" % challenge
-        packet += b"F" * (30 - len(packet))
-        packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet)])
-        self.connection.write(packet)
-        try:
-            self._confirm_serial()
-        except ConnectionError:
-            # If we could not access the status, then we did not confirm the serial number.
-            pass
-
-    def update_state(self, state):
-        with self._loop_cond:
-            self._loop_cond.notify()
-        if state == self.state:
-            return
-        self.state = state
-        if self.context is not None:
-            self.context.signal("pipe;thread", self.state)
-
-    def update_buffer(self):
-        self.context.signal("pipe;buffer", len(self))
-
-    def update_packet(self, packet):
-        self.context.signal("pipe;packet", convert_to_list_bytes(packet))
-        self.context.signal("pipe;packet_text", packet)
-        if self.usb_send_channel:
-            self.usb_send_channel(packet)
-
-    def _thread_loop(self):
-        while self.state not in ("end", "terminate"):
-            if self.state == "init":
-                # If we are initialized. Change that to active since we're running.
-                self.update_state("active")
-            elif self.state in ("pause", "busy", "suspend"):
-                # If we are paused just wait until the state changes.
-                if len(self._realtime_buffer) == 0 and len(self._preempt) == 0:
-                    # Only pause if there are no realtime commands to queue.
-                    self.context.laser_status = "idle"
-                    with self._loop_cond:
-                        self._loop_cond.wait()
-                    continue
-            if self.aborted_retries:
-                # We are not trying reconnection anymore.
-                self.context.laser_status = "idle"
-                with self._loop_cond:
-                    self._loop_cond.wait()
-                continue
-
-            self._check_transfer_buffer()
-            if len(self._realtime_buffer) <= 0 and len(self._buffer) <= 0:
-                # The buffer and realtime buffers are empty. No packet creation possible.
-                self.context.laser_status = "idle"
-                with self._loop_cond:
-                    self._loop_cond.wait()
-                continue
-
-            try:
-                # We try to process the queue.
-                queue_processed = self.process_queue()
-                if self.refuse_counts:
-                    self.context.signal("pipe;failing", 0)
-                self.refuse_counts = 0
-                if self.is_shutdown:
-                    return  # Sometimes it could reset this and escape.
-            except ConnectionRefusedError:
-                # The attempt refused the connection.
-                self.refuse_counts += 1
-                self.pre_ok = False
-                if self.refuse_counts >= 5:
-                    self.context.signal("pipe;state", "STATE_FAILED_RETRYING")
-                self.context.signal("pipe;failing", self.refuse_counts)
-                self.context.laser_status = "idle"
-                if self.is_shutdown:
-                    return  # Sometimes it could reset this and escape.
-                time.sleep(3)  # 3-second sleep on failed connection attempt.
-                continue
-            except ConnectionError:
-                # There was an error with the connection, close it and try again.
-                self.connection_errors += 1
-                self.pre_ok = False
-
-                self.context.laser_status = "idle"
-                time.sleep(0.5)
-                self.close()
-                continue
-
-            self.context.laser_status = "active" if queue_processed else "idle"
-            if queue_processed:
-                # Packet was sent.
-                if self.state not in (
-                    "pause",
-                    "busy",
-                    "active",
-                    "terminate",
-                ):
-                    self.update_state("active")
-                continue
-            # No packet could be sent.
-            if self.state not in (
-                "pause",
-                "busy",
-                "terminate",
-            ):
-                self.update_state("idle")
-
-    def _thread_data_send(self):
-        """
-        Main threaded function to send data. While the controller is working the thread
-        will be doing work in this function.
-        """
-        with self._main_lock:
-            self.pre_ok = False
-            self.is_shutdown = False
-            self._thread_loop()
-            self._thread = None
-            self.update_state("end")
-            self.pre_ok = False
-            self.context.laser_status = "idle"
-
-    def _check_transfer_buffer(self):
-        if len(self._queue):  # check for and append queue
-            with self._queue_lock:
-                self._buffer += self._queue
-                self._queue.clear()
-            self.update_buffer()
-
-        if len(self._preempt):  # check for and prepend preempt
-            with self._preempt_lock:
-                self._realtime_buffer += self._preempt
-                self._preempt.clear()
-            self.update_buffer()
-
-    def process_queue(self):
-        """
-        Attempts to process the buffer/queue
-        Will fail on ConnectionRefusedError at open, 'process_queue_pause = True' (anytime before packet sent),
-        self._buffer is empty, or a failure to produce packet.
-
-        Buffer will not be changed unless packet is successfully sent, or pipe commands are processed.
-
-        The following are meta commands for the controller
-        - : require wait finish at the end of the queue processing.
-        * : clear the buffers, and abort the thread.
-        ! : pause.
-        & : resume.
-        % : fail checksum, do not resend
-        ~ : begin/end realtime exception (Note, these characters would be consumed during
-                the write process and should not exist in the queue)
-        \x18 : quit.
-
-        @return: queue process success.
-        """
-        if len(self._realtime_buffer) > 0:
-            buffer = self._realtime_buffer
-            realtime = True
-        elif len(self._buffer) > 0:
-            buffer = self._buffer
-            realtime = False
-        else:
-            return False
-
-        # Find buffer of 30 or containing '\n'.
-        find = buffer.find(b"\n", 0, 30)
-        if find == -1:  # No end found.
-            length = min(30, len(buffer))
-        else:  # Line end found.
-            length = min(30, len(buffer), find + 1)
-        packet = bytes(buffer[:length])
-
-        # edge condition of catching only pipe command without '\n'
-        if packet.endswith((b"-", b"*", b"&", b"!", b"#", b"%", b"\x18")):
-            packet += buffer[length : length + 1]
-            length += 1
-        post_send_command = None
-        default_checksum = True
-
-        # find pipe commands.
-        if packet.endswith(b"\n"):
-            packet = packet[:-1]
-            if packet.endswith(b"-"):  # wait finish
-                packet = packet[:-1]
-                post_send_command = self.wait_finished
-            elif packet.endswith(b"*"):  # abort
-                post_send_command = self.abort
-                packet = packet[:-1]
-            elif packet.endswith(b"&"):  # resume
-                self._resume_busy()
-                packet = packet[:-1]
-            elif packet.endswith(b"!"):  # pause
-                self._pause_busy()
-                packet = packet[:-1]
-            elif packet.endswith(b"%"):  # alt-checksum
-                default_checksum = False
-                packet = packet[:-1]
-            elif packet.endswith(b"\x18"):
-                self.update_state("terminate")
-                self.is_shutdown = True
-                packet = packet[:-1]
-            if packet.startswith(b"A"):
-                # This is a challenge code. A is only used for serial challenges.
-                post_send_command = self._confirm_serial
-            if len(packet) != 0:
-                if packet.endswith(b"#"):
-                    packet = packet[:-1]
-                    try:
-                        c = packet[-1]
-                    except IndexError:
-                        c = b"F"  # Packet was simply #. We can do nothing.
-                    packet += bytes([c]) * (30 - len(packet))  # Padding. '\n'
-                else:
-                    packet += b"F" * (30 - len(packet))  # Padding. '\n'
-        if not realtime and self.state in ("pause", "busy"):
-            return False  # Processing normal queue, PAUSE and BUSY apply.
-
-        # Packet is prepared and ready to send. Open Channel.
-        self.open()
-
-        if len(packet) == 30:
-            # We have a sendable packet.
-            if not self.pre_ok:
-                self.wait_until_accepting_packets()
-            if default_checksum:
-                packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet)])
-            else:
-                packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet) ^ 0xFF])
-            self.connection.write(packet)
-            self.pre_ok = False
-
-            # Packet is sent, trying to confirm.
-            status = 0
-            flawless = True
-            for attempts in range(500):
-                # We'll try to confirm this at 500 times.
-                try:
-                    self.update_status()
-                    status = self._status[1]
-                    if attempts > 10:
-                        time.sleep(min(0.001 * attempts, 0.1))
-                except ConnectionError:
-                    # Errors are ignored, must confirm packet.
-                    flawless = False
-                    continue
-                if status == 0:
-                    # We did not read a status.
-                    continue
-                elif status == STATUS_OK:
-                    # Packet was fine.
-                    self.pre_ok = True
-                    break
-                elif status == STATUS_BUSY:
-                    # Busy. We still do not have our confirmation. BUSY comes before ERROR or OK.
-                    continue
-                elif status == STATUS_ERROR:
-                    if not default_checksum:
-                        break
-                    self.context.rejected_count += 1
-                    if flawless:  # Packet was rejected. The CRC failed.
-                        return False
-                    else:
-                        # The channel had the error, assuming packet was actually good.
-                        break
-                elif status == STATUS_FINISH:
-                    # We finished. If we were going to wait for that, we no longer need to.
-                    if post_send_command == self.wait_finished:
-                        post_send_command = None
-                    continue  # This is not a confirmation.
-                elif status == STATUS_SERIAL_CORRECT_M3_FINISH:
-                    if post_send_command == self._confirm_serial:
-                        # We confirmed the serial number on the card.
-                        self.serial_confirmed = True
-                        post_send_command = None
-                        break
-                    elif post_send_command == self.wait_finished:
-                        # This is a STATUS_M3_FINISHED, we no longer wait.
-                        post_send_command = None
-                        continue
-
-            if status == 0:  # After 500 attempts we could only get status = 0.
-                raise ConnectionError  # Broken pipe. Could not confirm packet.
-            self.context.packet_count += (
-                1  # Our packet is confirmed or assumed confirmed.
-            )
-        else:
-            if len(packet) != 0:
-                # We could only generate a partial packet, throw it back
-                return False
-            # We have an empty packet of only commands. Continue work.
-
-        # Packet was processed. Remove that data.
-        if realtime:
-            del self._realtime_buffer[:length]
-        else:
-            del self._buffer[:length]
-        if len(packet) != 0:
-            # Packet was completed and sent. Only then update the channel.
-            self.update_packet(packet)
-        self.update_buffer()
-
-        if post_send_command is not None:
-            # Post send command could be wait_finished, and might have a broken pipe.
-            try:
-                post_send_command()
-            except ConnectionError:
-                # We should have already sent the packet. So this should be fine.
-                pass
-        return True  # A packet was prepped and sent correctly.
-
-    def update_status(self):
-        try:
-            self._status = self.connection.get_status()
-        except AttributeError:
-            # self.connection was closed by something.
-            raise ConnectionError
-        if self.context is not None:
-            try:
-                self.context.signal(
-                    "pipe;status",
-                    self._status,
-                    get_code_string_from_code(self._status[1]),
-                )
-            except IndexError:
-                pass
-            if self.recv_channel:
-                self.recv_channel(str(self._status))
-
-    def wait_until_accepting_packets(self):
-        i = 0
-        while self.state != "terminate":
-            self.update_status()
-            if self._status is None:
-                raise ConnectionError
-            status = self._status[1]
-            if status == 0:
-                raise ConnectionError
-            if status == STATUS_OK:
-                self.pre_ok = False
-                break
-            if status == STATUS_ERROR:
-                break
-            time.sleep(0.05)
-            if self.context is not None:
-                self.context.signal("pipe;wait", STATUS_OK, i)
-            i += 1
-            if self.abort_waiting:
-                self.abort_waiting = False
-                return  # Wait abort was requested.
-
-    def wait_finished(self):
-        i = 0
-        original_state = self.state
-        if self.state != "pause":
-            self.pause()
-
-        while True:
-            if self.state != "wait":
-                if self.state == "terminate":
-                    return  # Abort all the processes was requested. This state change would be after clearing.
-                self.update_state("wait")
-            self.update_status()
-            status = self._status[1]
-            if status == 0:
-                raise ConnectionError
-            if status == STATUS_ERROR:
-                self.context.rejected_count += 1
-            if status & 0x02 == 0:
-                # StateBitPEMP = 0x00000200, Finished = 0xEC, 11101100
-                break
-            if self.context is not None:
-                self.context.signal("pipe;wait", status, i)
-            i += 1
-            if self.abort_waiting:
-                self.abort_waiting = False
-                break  # Wait abort was requested.
-            time.sleep(0.001)  # Only if we are using control transfer status checks.
-        self.update_state(original_state)
-
-    def _confirm_serial(self):
-        t = time.time()
-        while time.time() - t < 0.5:  # We spend up to half a second to confirm.
-            if self.state == "terminate":
-                # We are not confirmed.
-                return  # Abort all the processes was requested. This state change would be after clearing.
-            self.update_status()
-            status = self._status[1]
-            if status == STATUS_SERIAL_CORRECT_M3_FINISH:
-                self.serial_confirmed = True
-                return  # We're done.
-        self.serial_confirmed = False
+"""
+Lihuiyu Controller
+
+Deals with the sending of data via the registered connection, and processes some limited realtime commands.
+
+    - : require wait finish at the end of the queue processing.
+    * : clear the buffers, and abort the thread.
+    ! : pause.
+    & : resume.
+    % : fail checksum, do not resend
+    ~ : begin/end realtime exception (Note, these characters would be consumed during
+            the write process and should not exist in the queue)
+    \x18 : quit.
+
+"""
+
+import threading
+import time
+
+from meerk40t.ch341 import get_ch341_interface
+
+STATUS_SERIAL_CORRECT_M3_FINISH = 204
+# 0xCC, 11001100
+STATUS_OK = 206
+# 0xCE, 11001110
+STATUS_ERROR = 207
+# 0xCF, 11001111
+STATUS_FINISH = 236
+# 0xEC, 11101100
+STATUS_BUSY = 238
+# 0xEE, 11101110
+STATUS_POWER = 239
+
+
+STATE_X_FORWARD_LEFT = (
+    0b0000000000000001  # Direction is flagged left rather than right.
+)
+STATE_Y_FORWARD_TOP = 0b0000000000000010  # Direction is flagged top rather than bottom.
+STATE_X_STEPPER_ENABLE = 0b0000000000000100  # X-stepper motor is engaged.
+STATE_Y_STEPPER_ENABLE = 0b0000000000001000  # Y-stepper motor is engaged.
+STATE_HORIZONTAL_MAJOR = 0b0000000000010000
+REQUEST_X = 0b0000000000100000
+REQUEST_X_FORWARD_LEFT = 0b0000000001000000  # Requested direction towards the left.
+REQUEST_Y = 0b0000000010000000
+REQUEST_Y_FORWARD_TOP = 0b0000000100000000  # Requested direction towards the top.
+REQUEST_AXIS = 0b0000001000000000
+REQUEST_HORIZONTAL_MAJOR = 0b0000010000000000  # Requested horizontal major axis.
+
+
+def get_code_string_from_code(code):
+    if code == STATUS_OK:
+        return "OK"
+    elif code == STATUS_BUSY:
+        return "Busy"
+    elif code == STATUS_ERROR:
+        return "Rejected"
+    elif code == STATUS_FINISH:
+        return "Finish"
+    elif code == STATUS_POWER:
+        return "Low Power"
+    elif code == STATUS_SERIAL_CORRECT_M3_FINISH:
+        return "M3-Finished"
+    elif code == 0:
+        return "USB Failed"
+    else:
+        return f"UNK {code:02x}"
+
+
+def convert_to_list_bytes(data):
+    if isinstance(data, str):  # python 2
+        packet = [0] * 30
+        for i in range(0, 30):
+            packet[i] = ord(data[i])
+        return packet
+    else:
+        packet = [0] * 30
+        for i in range(0, 30):
+            packet[i] = data[i]
+        return packet
+
+
+crc_table = [
+    0x00,
+    0x5E,
+    0xBC,
+    0xE2,
+    0x61,
+    0x3F,
+    0xDD,
+    0x83,
+    0xC2,
+    0x9C,
+    0x7E,
+    0x20,
+    0xA3,
+    0xFD,
+    0x1F,
+    0x41,
+    0x00,
+    0x9D,
+    0x23,
+    0xBE,
+    0x46,
+    0xDB,
+    0x65,
+    0xF8,
+    0x8C,
+    0x11,
+    0xAF,
+    0x32,
+    0xCA,
+    0x57,
+    0xE9,
+    0x74,
+]
+
+
+def onewire_crc_lookup(line):
+    """
+    License: 2-clause "simplified" BSD license
+    Copyright (C) 1992-2017 Arjen Lentz
+    https://lentz.com.au/blog/calculating-crc-with-a-tiny-32-entry-lookup-table
+
+    @param line: line to be CRC'd
+    @return: 8 bit crc of line.
+    """
+    crc = 0
+    for i in range(0, 30):
+        crc = line[i] ^ crc
+        crc = crc_table[crc & 0x0F] ^ crc_table[16 + ((crc >> 4) & 0x0F)]
+    return crc
+
+
+class LihuiyuController:
+    """
+    K40 Controller controls the Lihuiyu boards sending any queued data to the USB when the signal is not busy.
+
+    Opening and closing of the pipe are dealt with internally. There are three primary monitor data channels.
+    'send', 'recv' and 'usb'. They display the reading and writing of information to/from the USB and the USB connection
+    log, providing information about the connecting and error status of the USB device.
+    """
+
+    def __init__(self, service, *args, **kwargs):
+        self.context = service
+        self.state = "unknown"
+        self.is_shutdown = False
+        self.serial_confirmed = None
+
+        self._thread = None
+        self._buffer = (
+            bytearray()
+        )  # Threadsafe buffered commands to be sent to controller.
+        self._realtime_buffer = (
+            bytearray()  # Threadsafe realtime buffered commands to be sent to the controller.
+        )
+        self._queue = bytearray()  # Thread-unsafe additional commands to append.
+        self._preempt = (
+            bytearray()
+        )  # Thread-unsafe preempt commands to prepend to the buffer.
+        self._queue_lock = threading.Lock()
+        self._preempt_lock = threading.Lock()
+        self._main_lock = threading.Lock()
+        self._connect_lock = threading.RLock()
+        self._loop_cond = threading.Condition()
+
+        self._status = [0] * 6
+        self._usb_state = -1
+
+        self.connection = None
+        self.max_attempts = 5
+        self.refuse_counts = 0
+        self.connection_errors = 0
+        self.aborted_retries = False
+        self.pre_ok = False
+        self.realtime = False
+
+        self.abort_waiting = False
+
+        name = service.safe_label
+        self.pipe_channel = service.channel(f"{name}/events")
+        self.usb_log = service.channel(f"{name}/usb", buffer_size=500)
+        self.usb_send_channel = service.channel(f"{name}/usb_send")
+        self.recv_channel = service.channel(f"{name}/recv")
+        self.usb_log.watch(lambda e: service.signal("pipe;usb_status", e))
+        self.reset()
+
+    @property
+    def viewbuffer(self):
+        buffer = bytes(self._realtime_buffer) + bytes(self._buffer) + bytes(self._queue)
+        try:
+            buffer_str = buffer.decode()
+        except ValueError:
+            try:
+                buffer_str = buffer.decode("utf8")
+            except UnicodeDecodeError:
+                buffer_str = str(buffer)
+        except AttributeError:
+            buffer_str = buffer
+        return buffer_str
+
+    def added(self):
+        self.start()
+
+    def service_detach(self):
+        pass
+
+    def shutdown(self, *args, **kwargs):
+        if self._thread is not None:
+            self.realtime_write(b"\x18\n")
+
+    def __repr__(self):
+        return f"LihuiyuController({str(self.context)})"
+
+    def __len__(self):
+        """Provides the length of the buffer of this device."""
+        return len(self._buffer) + len(self._queue) + len(self._preempt)
+
+    def open(self):
+        with self._connect_lock:
+            self._process_open()
+
+    def _process_open(self):
+        if self.connection is not None and self.connection.is_connected():
+            return  # Already connected.
+        _ = self.usb_log._
+        self.pipe_channel("open()")
+        try:
+            interfaces = list(
+                get_ch341_interface(
+                    self.context,
+                    self.usb_log,
+                    mock=self.context.mock,
+                    mock_status=STATUS_OK,
+                    bulk=True,
+                )
+            )
+            if self.context.usb_index != -1:
+                # Instructed to check one specific device.
+                devices = [self.context.usb_index]
+            else:
+                devices = range(16)
+
+            for interface in interfaces:
+                self.connection = interface
+                for i in devices:
+                    try:
+                        self._open_at_index(i)
+                        return  # Opened successfully.
+                    except ConnectionRefusedError as e:
+                        self.usb_log(str(e))
+                        if self.connection is not None:
+                            self.connection.close()
+                    except IndexError:
+                        self.usb_log(_("Connection failed."))
+                        self.connection = None
+                        break
+        except PermissionError as e:
+            self.usb_log(str(e))
+            return  # OS denied permissions, no point checking anything else.
+
+        self.close()
+        raise ConnectionRefusedError(
+            _("No valid connection matched any given criteria.")
+        )
+
+    def _open_at_index(self, usb_index):
+        _ = self.context.kernel.translation
+        self.connection.open(usb_index=usb_index)
+        if not self.connection.is_connected():
+            raise ConnectionRefusedError("ch341 connect did not return a connection.")
+        if self.context.usb_bus != -1 and self.connection.bus != -1:
+            if self.connection.bus != self.context.usb_bus:
+                raise ConnectionRefusedError(
+                    _("K40 devices were found but they were rejected due to usb bus.")
+                )
+        if self.context.usb_address != -1 and self.connection.address != -1:
+            if self.connection.address != self.context.usb_address:
+                raise ConnectionRefusedError(
+                    _(
+                        "K40 devices were found but they were rejected due to usb address."
+                    )
+                )
+        if self.context.usb_version != -1:
+            version = self.connection.get_chip_version()
+            if version != self.context.usb_version:
+                raise ConnectionRefusedError(
+                    _(
+                        "K40 devices were found but they were rejected due to chip version."
+                    )
+                )
+        if self.context.serial_enable and self.context.serial is not None:
+            if self.serial_confirmed:
+                return  # already passed.
+            self.usb_log(_("Requires serial number confirmation."))
+            self.challenge(self.context.serial)
+            t = time.time()
+            while time.time() - t < 0.5:
+                if self.serial_confirmed:
+                    break
+            if not self.serial_confirmed:
+                raise ConnectionRefusedError("Serial number confirmation failed.")
+            else:
+                self.usb_log(_("Serial number confirmed."))
+
+    def close(self):
+        self.pipe_channel("close()")
+        with self._connect_lock:
+            if self.connection is None:
+                return
+            self.connection.close()
+            self.connection = None
+
+    def write(self, bytes_to_write):
+        """
+        Writes data to the queue, this will be moved into the buffer by the thread in a threadsafe manner.
+
+        @param bytes_to_write: data to write to the queue.
+        @return:
+        """
+        f = bytes_to_write.find(b"~")
+        if f != -1:
+            # ~ was found in bytes. We are in a realtime exception.
+            self.realtime = True
+
+            # All code prior to ~ is sent to write.
+            queue_bytes = bytes_to_write[:f]
+            if queue_bytes:
+                self.write(queue_bytes)
+
+            # All code after ~ is sent to realtime write.
+            preempt_bytes = bytes_to_write[f + 1 :]
+            if preempt_bytes:
+                self.realtime_write(preempt_bytes)
+            return self
+        if self.realtime:
+            # We are in a realtime exception that has not been terminated.
+            self.realtime_write(bytes_to_write)
+            return self
+
+        self.pipe_channel(f"write({str(bytes_to_write)})")
+        with self._queue_lock:
+            self._queue += bytes_to_write
+        self.start()
+        self.update_buffer()
+        return self
+
+    def realtime_write(self, bytes_to_write):
+        """
+        Writes data to the preempting commands, this will be moved to the front of the buffer by the thread
+        in a threadsafe manner.
+
+        @param bytes_to_write: data to write to the front of the queue.
+        @return:
+        """
+        f = bytes_to_write.find(b"~")
+        if f != -1:
+            # ~ was found in bytes. We are leaving realtime exception.
+            self.realtime = False
+
+            # All date prior to the ~ is sent to realtime write.
+            preempt_bytes = bytes_to_write[:f]
+            if preempt_bytes:
+                self.realtime_write(preempt_bytes)
+
+            # All data after ~ is sent back to normal write.
+            queue_bytes = bytes_to_write[f + 1 :]
+            if queue_bytes:
+                self.write(queue_bytes)
+            return self
+        self.pipe_channel(f"realtime_write({str(bytes_to_write)})")
+        if b"*" in bytes_to_write:
+            self.abort_waiting = True
+        with self._preempt_lock:
+            self._preempt = bytearray(bytes_to_write) + self._preempt
+        self.start()
+        self.update_buffer()
+        return self
+
+    def start(self):
+        """
+        Controller state change to `Started`.
+        @return:
+        """
+        with self._loop_cond:
+            self._loop_cond.notify()
+        if not self.is_shutdown and (
+            self._thread is None or not self._thread.is_alive()
+        ):
+            self.update_state("init")
+            self._thread = self.context.threaded(
+                self._thread_data_send,
+                thread_name=f"LhyPipe({self.context.path})",
+                result=self.stop,
+            )
+            self._thread.stop = self.stop
+
+    def _pause_busy(self):
+        """
+        BUSY can be called in a paused state to packet halt the controller.
+
+        This can only be done from PAUSE.
+        """
+        if self.state != "pause":
+            self.pause()
+        if self.state == "pause":
+            self.update_state("busy")
+
+    def _resume_busy(self):
+        """
+        Resumes from a BUSY to restore the controller. This will return to a paused state.
+
+        This can only be done from BUSY.
+        """
+        if self.state == "busy":
+            self.update_state("pause")
+            self.resume()
+
+    def pause(self):
+        """
+        Pause simply holds the controller from sending any additional packets.
+
+        If this state change is done from INITIALIZE it will start the processing.
+        Otherwise, it must be done from ACTIVE or IDLE.
+        """
+        if self.state == "init":
+            self.start()
+            self.update_state("pause")
+        if self.state in ("active", "idle"):
+            self.update_state("pause")
+
+    def resume(self):
+        """
+        Resume can only be called from PAUSE.
+        """
+        if self.state == "pause":
+            self.update_state("active")
+
+    def abort(self):
+        self._buffer = bytearray()
+        self._queue = bytearray()
+        self._realtime_buffer = bytearray()
+        self.abort_waiting = False
+        self.context.signal("pipe;buffer", 0)
+        self.update_state("terminate")
+
+    def reset(self):
+        self.update_state("init")
+
+    def stop(self, *args):
+        self.abort()
+        try:
+            if self._thread is not None:
+                self._thread.join()  # Wait until stop completes before continuing.
+            self._thread = None
+        except RuntimeError:
+            pass  # Stop called by current thread.
+
+    def abort_retry(self):
+        with self._loop_cond:
+            self._loop_cond.notify()
+        self.aborted_retries = True
+        self.context.signal("pipe;state", "STATE_FAILED_SUSPENDED")
+
+    def continue_retry(self):
+        with self._loop_cond:
+            self._loop_cond.notify()
+        self.aborted_retries = False
+        self.context.signal("pipe;state", "STATE_FAILED_RETRYING")
+
+    def usb_release(self):
+        if self.connection:
+            self.connection.release()
+        else:
+            raise ConnectionError
+
+    def usb_reset(self):
+        if self.connection:
+            self.connection.reset()
+        else:
+            raise ConnectionError
+
+    def challenge(self, serial):
+        if serial is None:
+            return
+
+        from hashlib import md5
+
+        challenge = bytearray.fromhex(md5(bytes(serial.upper(), "utf8")).hexdigest())
+        packet = b"A%s" % challenge
+        packet += b"F" * (30 - len(packet))
+        packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet)])
+        self.connection.write(packet)
+        try:
+            self._confirm_serial()
+        except ConnectionError:
+            # If we could not access the status, then we did not confirm the serial number.
+            pass
+
+    def update_state(self, state):
+        with self._loop_cond:
+            self._loop_cond.notify()
+        if state == self.state:
+            return
+        self.state = state
+        if self.context is not None:
+            self.context.signal("pipe;thread", self.state)
+
+    def update_buffer(self):
+        self.context.signal("pipe;buffer", len(self))
+
+    def update_packet(self, packet):
+        self.context.signal("pipe;packet", convert_to_list_bytes(packet))
+        self.context.signal("pipe;packet_text", packet)
+        if self.usb_send_channel:
+            self.usb_send_channel(packet)
+
+    def _thread_loop(self):
+        while self.state not in ("end", "terminate"):
+            if self.state == "init":
+                # If we are initialized. Change that to active since we're running.
+                self.update_state("active")
+            elif self.state in ("pause", "busy", "suspend"):
+                # If we are paused just wait until the state changes.
+                if len(self._realtime_buffer) == 0 and len(self._preempt) == 0:
+                    # Only pause if there are no realtime commands to queue.
+                    self.context.laser_status = "idle"
+                    with self._loop_cond:
+                        self._loop_cond.wait()
+                    continue
+            if self.aborted_retries:
+                # We are not trying reconnection anymore.
+                self.context.laser_status = "idle"
+                with self._loop_cond:
+                    self._loop_cond.wait()
+                continue
+
+            self._check_transfer_buffer()
+            if len(self._realtime_buffer) <= 0 and len(self._buffer) <= 0:
+                # The buffer and realtime buffers are empty. No packet creation possible.
+                self.context.laser_status = "idle"
+                with self._loop_cond:
+                    self._loop_cond.wait()
+                continue
+
+            try:
+                # We try to process the queue.
+                queue_processed = self.process_queue()
+                if self.refuse_counts:
+                    self.context.signal("pipe;failing", 0)
+                self.refuse_counts = 0
+                if self.is_shutdown:
+                    return  # Sometimes it could reset this and escape.
+            except ConnectionRefusedError:
+                # The attempt refused the connection.
+                self.refuse_counts += 1
+                self.pre_ok = False
+                if self.refuse_counts >= 5:
+                    self.context.signal("pipe;state", "STATE_FAILED_RETRYING")
+                self.context.signal("pipe;failing", self.refuse_counts)
+                self.context.laser_status = "idle"
+                if self.is_shutdown:
+                    return  # Sometimes it could reset this and escape.
+                time.sleep(3)  # 3-second sleep on failed connection attempt.
+                continue
+            except ConnectionError:
+                # There was an error with the connection, close it and try again.
+                self.connection_errors += 1
+                self.pre_ok = False
+
+                self.context.laser_status = "idle"
+                time.sleep(0.5)
+                self.close()
+                continue
+
+            self.context.laser_status = "active" if queue_processed else "idle"
+            if queue_processed:
+                # Packet was sent.
+                if self.state not in (
+                    "pause",
+                    "busy",
+                    "active",
+                    "terminate",
+                ):
+                    self.update_state("active")
+                continue
+            # No packet could be sent.
+            if self.state not in (
+                "pause",
+                "busy",
+                "terminate",
+            ):
+                self.update_state("idle")
+
+    def _thread_data_send(self):
+        """
+        Main threaded function to send data. While the controller is working the thread
+        will be doing work in this function.
+        """
+        with self._main_lock:
+            self.pre_ok = False
+            self.is_shutdown = False
+            self._thread_loop()
+            self._thread = None
+            self.update_state("end")
+            self.pre_ok = False
+            self.context.laser_status = "idle"
+
+    def _check_transfer_buffer(self):
+        if len(self._queue):  # check for and append queue
+            with self._queue_lock:
+                self._buffer += self._queue
+                self._queue.clear()
+            self.update_buffer()
+
+        if len(self._preempt):  # check for and prepend preempt
+            with self._preempt_lock:
+                self._realtime_buffer += self._preempt
+                self._preempt.clear()
+            self.update_buffer()
+
+    def process_queue(self):
+        """
+        Attempts to process the buffer/queue
+        Will fail on ConnectionRefusedError at open, 'process_queue_pause = True' (anytime before packet sent),
+        self._buffer is empty, or a failure to produce packet.
+
+        Buffer will not be changed unless packet is successfully sent, or pipe commands are processed.
+
+        The following are meta commands for the controller
+        - : require wait finish at the end of the queue processing.
+        * : clear the buffers, and abort the thread.
+        ! : pause.
+        & : resume.
+        % : fail checksum, do not resend
+        ~ : begin/end realtime exception (Note, these characters would be consumed during
+                the write process and should not exist in the queue)
+        \x18 : quit.
+
+        @return: queue process success.
+        """
+        if len(self._realtime_buffer) > 0:
+            buffer = self._realtime_buffer
+            realtime = True
+        elif len(self._buffer) > 0:
+            buffer = self._buffer
+            realtime = False
+        else:
+            return False
+
+        # Find buffer of 30 or containing '\n'.
+        find = buffer.find(b"\n", 0, 30)
+        if find == -1:  # No end found.
+            length = min(30, len(buffer))
+        else:  # Line end found.
+            length = min(30, len(buffer), find + 1)
+        packet = bytes(buffer[:length])
+
+        # edge condition of catching only pipe command without '\n'
+        if packet.endswith((b"-", b"*", b"&", b"!", b"#", b"%", b"\x18")):
+            packet += buffer[length : length + 1]
+            length += 1
+        post_send_command = None
+        default_checksum = True
+
+        # find pipe commands.
+        if packet.endswith(b"\n"):
+            packet = packet[:-1]
+            # There's a special case where we have a trailing "\n" at an exactly 30 byte command,
+            # that requires another package of 30 x F to be sent, so we need to deal with an empty string...
+            if len(packet) == 0:
+                packet += b"F"
+            if packet.endswith(b"P"):
+                # This is a special case where the m3nano seems to fail. So we extend the buffer...
+                packet += b"F"
+            elif packet.endswith(b"-"):  # wait finish
+                packet = packet[:-1]
+                post_send_command = self.wait_finished
+            elif packet.endswith(b"*"):  # abort
+                post_send_command = self.abort
+                packet = packet[:-1]
+            elif packet.endswith(b"&"):  # resume
+                self._resume_busy()
+                packet = packet[:-1]
+            elif packet.endswith(b"!"):  # pause
+                self._pause_busy()
+                packet = packet[:-1]
+            elif packet.endswith(b"%"):  # alt-checksum
+                default_checksum = False
+                packet = packet[:-1]
+            elif packet.endswith(b"\x18"):
+                self.update_state("terminate")
+                self.is_shutdown = True
+                packet = packet[:-1]
+            if packet.startswith(b"A"):
+                # This is a challenge code. A is only used for serial challenges.
+                post_send_command = self._confirm_serial
+            if len(packet) != 0:
+                if packet.endswith(b"#"):
+                    packet = packet[:-1]
+                    try:
+                        c = packet[-1]
+                    except IndexError:
+                        c = b"F"  # Packet was simply #. We can do nothing.
+                    packet += bytes([c]) * (30 - len(packet))  # Padding. '\n'
+                else:
+                    packet += b"F" * (30 - len(packet))  # Padding. '\n'
+        if not realtime and self.state in ("pause", "busy"):
+            return False  # Processing normal queue, PAUSE and BUSY apply.
+
+        # Packet is prepared and ready to send. Open Channel.
+        self.open()
+
+        if len(packet) == 30:
+            # We have a sendable packet.
+            if not self.pre_ok:
+                self.wait_until_accepting_packets()
+            if default_checksum:
+                packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet)])
+            else:
+                packet = b"\x00" + packet + bytes([onewire_crc_lookup(packet) ^ 0xFF])
+            self.connection.write(packet)
+            self.pre_ok = False
+
+            # Packet is sent, trying to confirm.
+            status = 0
+            flawless = True
+            for attempts in range(500):
+                # We'll try to confirm this at 500 times.
+                try:
+                    self.update_status()
+                    status = self._status[1]
+                    if attempts > 10:
+                        time.sleep(min(0.001 * attempts, 0.1))
+                except ConnectionError:
+                    # Errors are ignored, must confirm packet.
+                    flawless = False
+                    continue
+                if status == 0:
+                    # We did not read a status.
+                    continue
+                if status == STATUS_OK:
+                    # Packet was fine.
+                    self.pre_ok = True
+                    break
+                elif status == STATUS_BUSY:
+                    # Busy. We still do not have our confirmation. BUSY comes before ERROR or OK.
+                    continue
+                elif status == STATUS_ERROR:
+                    if not default_checksum:
+                        break
+                    self.context.rejected_count += 1
+                    if flawless:  # Packet was rejected. The CRC failed.
+                        return False
+                    else:
+                        # The channel had the error, assuming packet was actually good.
+                        break
+                elif status == STATUS_FINISH:
+                    # We finished. If we were going to wait for that, we no longer need to.
+                    if post_send_command == self.wait_finished:
+                        post_send_command = None
+                    continue  # This is not a confirmation.
+                elif status == STATUS_SERIAL_CORRECT_M3_FINISH:
+                    if post_send_command == self._confirm_serial:
+                        # We confirmed the serial number on the card.
+                        self.serial_confirmed = True
+                        post_send_command = None
+                        break
+                    elif post_send_command == self.wait_finished:
+                        # This is a STATUS_M3_FINISHED, we no longer wait.
+                        post_send_command = None
+                        continue
+
+            if status == 0:  # After 500 attempts we could only get status = 0.
+                raise ConnectionError  # Broken pipe. Could not confirm packet.
+            self.context.packet_count += (
+                1  # Our packet is confirmed or assumed confirmed.
+            )
+        else:
+            if len(packet) != 0:
+                # We could only generate a partial packet, throw it back
+                return False
+            # We have an empty packet of only commands. Continue work.
+
+        # Packet was processed. Remove that data.
+        if realtime:
+            del self._realtime_buffer[:length]
+        else:
+            del self._buffer[:length]
+        if len(packet) != 0:
+            # Packet was completed and sent. Only then update the channel.
+            self.update_packet(packet)
+        self.update_buffer()
+
+        if post_send_command is not None:
+            # Post send command could be wait_finished, and might have a broken pipe.
+            try:
+                post_send_command()
+            except ConnectionError:
+                # We should have already sent the packet. So this should be fine.
+                pass
+        return True  # A packet was prepped and sent correctly.
+
+    def update_status(self):
+        try:
+            self._status = self.connection.get_status()
+        except AttributeError:
+            # self.connection was closed by something.
+            raise ConnectionError
+        if self.context is not None:
+            try:
+                self.context.signal(
+                    "pipe;status",
+                    self._status,
+                    get_code_string_from_code(self._status[1]),
+                )
+            except IndexError:
+                pass
+            if self.recv_channel:
+                self.recv_channel(str(self._status))
+
+    def wait_until_accepting_packets(self):
+        i = 0
+        while self.state != "terminate":
+            self.update_status()
+            if self._status is None:
+                raise ConnectionError
+            status = self._status[1]
+            if status == 0:
+                raise ConnectionError
+            if status == STATUS_OK:
+                self.pre_ok = False
+                break
+            if status == STATUS_ERROR:
+                break
+            time.sleep(0.05)
+            if self.context is not None:
+                self.context.signal("pipe;wait", STATUS_OK, i)
+            i += 1
+            if self.abort_waiting:
+                self.abort_waiting = False
+                return  # Wait abort was requested.
+
+    def wait_finished(self):
+        i = 0
+        original_state = self.state
+        if self.state != "pause":
+            self.pause()
+
+        while True:
+            if self.state != "wait":
+                if self.state == "terminate":
+                    return  # Abort all the processes was requested. This state change would be after clearing.
+                self.update_state("wait")
+            self.update_status()
+            status = self._status[1]
+            if status == 0:
+                raise ConnectionError
+            if status == STATUS_ERROR:
+                self.context.rejected_count += 1
+            if status & 0x02 == 0:
+                # StateBitPEMP = 0x00000200, Finished = 0xEC, 11101100
+                break
+            if self.context is not None:
+                self.context.signal("pipe;wait", status, i)
+            i += 1
+            if self.abort_waiting:
+                self.abort_waiting = False
+                break  # Wait abort was requested.
+            time.sleep(0.001)  # Only if we are using control transfer status checks.
+        self.update_state(original_state)
+
+    def _confirm_serial(self):
+        t = time.time()
+        while time.time() - t < 0.5:  # We spend up to half a second to confirm.
+            if self.state == "terminate":
+                # We are not confirmed.
+                return  # Abort all the processes was requested. This state change would be after clearing.
+            self.update_status()
+            status = self._status[1]
+            if status == STATUS_SERIAL_CORRECT_M3_FINISH:
+                self.serial_confirmed = True
+                return  # We're done.
+        self.serial_confirmed = False