@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x0129/yrl216.json

@@ -53,9 +53,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To include; Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "To exclude; Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit Master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key",
+		"exclusion": "1. Enter the 4-8 digit Master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 3 key followed by the gear key",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n4. Release reset button\n5. Replace battery cover",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3129/Assure_Lever_Manual_ZWave_Cert.pdf"
 	}
 }

package/config/devices/0x0129/yrl226.json

@@ -57,9 +57,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit Master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key",
+		"exclusion": "1. Enter the 4-8 digit Master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 3 key followed by the gear key",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n4. Release reset button\n5. Replace battery cover",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3114/YRL226-ZW2.pdf"
 	}
 }

package/config/devices/0x0129/yrl256.json

@@ -97,8 +97,8 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Install Yale Smart Module into slot above battery compartment\nIMPORTANT: Batteries must be removed before inserting Yale Smart Module:\n• Remove battery cover\n• Remove batteries\n• Insert Yale Smart Module\n• Reinstall batteries\n• Reinstall battery cover\n2. Open Z-Wave system's smart home or alarm app on your smartphone or tablet\n3. If you have Smart Start* enabled with your Z-Wave System follow in-app prompts to add a new device\nIf you don't have smart start or are not sure, follow steps 4 - 6\n4. On your lock keypad, enter your master entry code followed by the gear icon\n5. Press the 7 key followed by the gear icon\n6. Press the 1 key followed by the gear icon",
-		"exclusion": "Open Z-Wave system's smart home or alarm app and follow instructions for removing a device\n2. On your lock keypad, enter your master entry code followed by the icon\n3. Press the 7 key followed by the gear icon\n4. Press the 3 key followed by the gear icon",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "1. Remove the battery cover and batteries\n2. Insert the Yale Smart Module into the slot above the battery compartment\n3. Reinstall the batteries and battery cover\n4. Enter your master entry code followed by the gear icon\n5. Press the 7 key followed by the gear icon\n6. Press the 1 key followed by the gear icon",
+		"exclusion": "1. Enter your master entry code followed by the gear icon\n2. Press the 7 key followed by the gear icon\n3. Press the 3 key followed by the gear icon",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button above the PCB cable connector\n3. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries\n4. Release the reset button and replace the battery cover"
 	}
 }

package/config/devices/0x0129/yrm276.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\nWhen resetting the lock, all user codes,including the Master code*, are deleted. All programming features are reset to the original default settings.\n1. Remove the battery cover and batteries.\n2. Remove the interior lock to access the reset button.\n3. The reset button is located above the cable connectors. PCB\n4. Re-insert 3 batteries and hold the reset button for 3 seconds.\n5. While still holding the reset button, insert the 4th battery, and hold the reset button for an additional 3 seconds.\n6. Release the reset button.\n7. Re-install the interior lock onto the door.Upon reset, Master Code creation is the PIN only option available and must be performed prior to any other programming of the lock.\n For best results, the lock should be installed on the door when resetting the lock to factory default. If the process was done and the lock was not installed on the door, review the Re-Handing instructions listed in Hardware Troubleshooting",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 3 key followed by the gear key",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior lock to access the reset button above the cable connectors on the PCB\n3. Re-insert 3 batteries and hold the reset button for 3 seconds\n4. While still holding the reset button, insert the 4th battery and hold for an additional 3 seconds\n5. Release the reset button and re-install the interior lock onto the door",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2911/YRM276_YRM476-INST-FUL%20Rev%20A%20WEB_SystemGuide.pdf"
 	}
 }

package/config/devices/0x0129/yrm476.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\nWhen resetting the lock, all user codes,including the Master code*, are deleted. All programming features are reset to the original default settings.\n1. Remove the battery cover and batteries.\n2. Remove the interior lock to access the reset button.\n3. The reset button is located above the cable connectors. PCB\n4. Re-insert 3 batteries and hold the reset button for 3 seconds.\n5. While still holding the reset button, insert the 4th battery, and hold the reset button for an additional 3 seconds.\n6. Release the reset button.\n7. Re-install the interior lock onto the door.Upon reset, Master Code creation is the PIN only option available and must be performed prior to any other programming of the lock.\n For best results, the lock should be installed on the door when resetting the lock to factory default. If the process was done and the lock was not installed on the door, review the Re-Handing instructions listed in Hardware Troubleshooting",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 3 key followed by the gear key",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior lock to access the reset button above the cable connectors on the PCB\n3. Re-insert 3 batteries and hold the reset button for 3 seconds\n4. While still holding the reset button, insert the 4th battery and hold for an additional 3 seconds\n5. Release the reset button and re-install the interior lock onto the door",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2925/YRM276_YRM476-INST-FUL%20Rev%20A%20WEB_SystemGuide.pdf"
 	}
 }

package/config/devices/0x012a/iq_dimmer.json

@@ -69,7 +69,7 @@
 	"metadata": {
 		"inclusion": "Single click the button on the top of the IQ Dimmer.",
 		"exclusion": "Single click the button on the top of the IQ Dimmer.",
-		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plug of the appliance from the IQ Dimmer (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed",
+		"reset": "1. Unplug the IQ Dimmer from the AC outlet and unplug the power plug of the appliance from the IQ Dimmer\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4089/IQ%20Dimmer%20User%20Guide%20031921.pdf"
 	}
 }

package/config/devices/0x012a/iq_outlet.json

@@ -67,7 +67,7 @@
 	"metadata": {
 		"inclusion": "Single click the button on the top of the IQ Outlet.",
 		"exclusion": "Single click the button on the top of the IQ Outlet.",
-		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plug of the appliance from the IQ Outlet (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed",
+		"reset": "1. Unplug the IQ Outlet from the AC outlet and unplug the power plug of the appliance from the IQ Outlet\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4133/IQ%20Outlet%20User%20Guide%20032421.pdf"
 	}
 }

package/config/devices/0x012a/iqpanel2.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device\n10. Adjust device name as needed\n11. Select Automation\n12. Click Add to save",
+		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device",
 		"exclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Delete failed device from panel\n8. Check boxes next to devices you want to delete\n9. Touch Delete",
 		"reset": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Remove All Devices",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3092/IQ%20Panel%20Installation%20Manual%202.2.1%20FINAL.pdf"

package/config/devices/0x012a/qs9201-1208-840.json

@@ -27,7 +27,7 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device\n10. Adjust device name as needed\n11. Select Automation\n12. Click Add to save",
+		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device",
 		"exclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Delete failed device from panel\n8. Check boxes next to devices you want to delete\n9. Touch Delete",
 		"reset": "1. Swipe down from the top of the screen\n2. Touch Settings\n3. Touch Advanced Settings\n4. Enter installer code\n5. Touch Installation\n6. Touch Devices\n7. Touch Z-Wave Devices\n8. Touch Remove All Devices\n9. Touch Yes to confirm",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3821/IQ%20Panel%20Installation%20Manual%202.5.0%20FINAL.pdf"

package/config/devices/0x012a/qz2130-840.json

@@ -28,7 +28,7 @@
 	"metadata": {
 		"inclusion": "Single click the button on the front of the IQ Outlet.",
 		"exclusion": "Single click the button on the front of the IQ Outlet.",
-		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed\n4. After 3 seconds, release the button\nIf you see the button blink, the IQ Outlet has been reset successfully.",
+		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed\n4. After 3 seconds, release the button. If you see the button blink, the IQ Outlet has been reset successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3032/IQ%20Outlet%20User%20Manual%20060718.pdf"
 	}
 }

package/config/devices/0x012a/qz2140-840.json

@@ -47,7 +47,7 @@
 	"metadata": {
 		"inclusion": "Single click the button on the front of the IQ Dimmer.",
 		"exclusion": "Single click the button on the front of the IQ Dimmer.",
-		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed. After 3 seconds, release the button\nThe button will blink to confirm successful reset.",
+		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed\n4. After 3 seconds, release the button. The button will blink to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2912/IQ%20Dimmer%20UG%20Online.pdf"
 	}
 }

package/config/devices/0x012a/qz2142-840.json

@@ -224,7 +224,7 @@
 	"metadata": {
 		"inclusion": "Click the button three times within one second.",
 		"exclusion": "Click the button three times within one second.",
-		"reset": "Click the Z-Wave button 3 times quickly, and hold for at least 10 seconds on the third click to restore factory settings.",
+		"reset": "Click the Z-Wave button 3 times quickly and hold for at least 10 seconds on the third click to restore factory settings.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4463/IQSmartDimmerManual_v2.pdf"
 	}
 }

package/config/devices/0x0130/6500-1400-6000.json

@@ -107,9 +107,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the Energy Meter Reader into a Z-Wave network, the inclu-sion process should be started on the controller. In factory default mode, the Energy Meter Reader will try to join a Z-Wave network automatically after being plugged into a power socket. If the Energy Meter Reader was previously included in a Z-Wave network, or was not just plugged into a power socket, one needs to triple-press the button (quickly)",
-		"exclusion": "To remove the Energy Meter Reader from a Z-wave network, the exclusion process should be started on the controller. The button on the Energy Meter Reader should then be triple-pressed (quickly)",
-		"reset": "The Energy Meter Reader can be reset to factory default by pressing and holding the button for approximately 10 seconds. This will reset the entire device to factory default, also removing the Z-Wave set-tings. After the reset is complete, both LEDs will blink a single time (indicating startup). If the device was connected to a Z-Wave net-work, it will no longer be connected after reset.\nPlease use this procedure only in the event that the primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple-press the button quickly.",
+		"exclusion": "Triple-press the button quickly.",
+		"reset": "Press and hold the button for approximately 10 seconds. After the reset is complete, both LEDs will blink a single time.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1281/Manual%20meteradapter.pdf"
 	}
 }

package/config/devices/0x0130/qb3_x.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To start learn mode, go to the 'Network functionality' tab and press either the 'Classic' or 'NWI' button, under the 'Learn Mode' header. This will open up a learn mode popup.\nPress the 'Start' button to start the learn mode. The dialog will show this device's DSK, which can be used to include the device securely into an existing Z-Wave network. Enter the first 5 digits of the\nDSK on the including node.\n\nLearn mode can be used to add this device into another Z-Wave network. It can also be used to\nreceive network information from another controller\n\nWhen learn mode has completed, the dialog will be updated to show the status. Press the 'Close' button to close the dialog.",
-		"exclusion": "To exclude a device from the network, go to the 'Network functionality' tab and press the 'Exclude' button. This will open up the 'Exclude Device' popup.\nPress the 'Start' button to start the exclusion process. Next press the exclusion button (or use another way to start the learn mode) on the to-be-excluded node.\nWhen the exclusion process has completed successfully, the dialog will show which node has been excluded. Press the 'Close' button to close the dialog.",
-		"reset": "The Z-Wave functionality of the device can be reset to factory defaults by using the 'Factory Reset'\nbutton on the 'Network functionality' tab. Pressing this button will open the Factory Reset dialog.\nIf you press the 'Reset' button in the dialog, all Z-Wave functionality will be reset to factory defaults.\nAll information about included devices will be lost. A new HomeID will be generated following a successful factory reset. Please use this procedure only when the network primary controller is\nmissing or otherwise inoperable.",
+		"inclusion": "1. Go to the 'Network functionality' tab and press either the 'Classic' or 'NWI' button under the 'Learn Mode' header.\n2. Press the 'Start' button to start the learn mode.\n3. Enter the first 5 digits of the DSK on the including node.\n4. Press the 'Close' button to close the dialog when completed.",
+		"exclusion": "1. Go to the 'Network functionality' tab and press the 'Exclude' button.\n2. Press the 'Start' button to start the exclusion process.\n3. Press the 'Close' button to close the dialog when completed.",
+		"reset": "1. Go to the 'Network functionality' tab and press the 'Factory Reset' button.\n2. Press the 'Reset' button in the dialog to reset all Z-Wave functionality to factory defaults.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3820/QB3%20documentation%20v1_2.pdf"
 	}
 }

package/config/devices/0x0131/ah-neo-ds07z.json

@@ -117,8 +117,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power Up The Device.\n2. Set Z-Wave Controller Into Inclusion Mode\n3. Press And Hold The Button For 5s Until White Led Lights Is On, Then Release The Button Before Led Turn Off.\nBlue Led Will Blink With 1s Interval Until Inclusion Successful.",
-		"exclusion": "1. Power Up The Device.\n2. Set Z-Wave Controller Into Exclusion Mode\n3. Press And Hold The Button For 5s Until White Led Lights Is On, Then Release The Button Before Led Turn Off.\nBlue Led Will Blink With 0.5sinterval Until Exclusion Successful.",
-		"reset": "1. Power Up The Device.\n2. Press And Hold The Button For 10s Until Pink Led Lights Is On, Then Release The Button Before Led Turn Off."
+		"inclusion": "1. Power up the device.\n2. Press and hold the button for 5 seconds until the white LED turns on, then release before it turns off.\n3. The blue LED will blink every second until inclusion is successful.",
+		"exclusion": "1. Power up the device.\n2. Press and hold the button for 5 seconds until the white LED turns on, then release before it turns off.\n3. The blue LED will blink every 0.5 seconds until exclusion is successful.",
+		"reset": "1. Power up the device.\n2. Press and hold the button for 10 seconds until the pink LED turns on, then release before it turns off."
 	}
 }

package/config/devices/0x0131/gr-105.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2.Once the controller is ready to include your device, press the red button 3 times to include it in the Z-Wave network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device to the Z-Wave network.\n2.Once the controller is ready to exclude your device, press the red button 3 times to exclude it from the Z-Wave network.",
-		"reset": "Press and hold the button 10 seconds and release the button. The device will send the reset notification to the list node in the group1 and erases the device memory , when the light flash it is resetting success.\nNote: This should only be used in the event your networks primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the red button 3 times.",
+		"exclusion": "Press the red button 3 times.",
+		"reset": "Press and hold the button for 10 seconds and release the button. When the light flashes it indicates resetting is successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2851/zipatoValve.pdf"
 	}
 }

package/config/devices/0x0131/ne-nas-ds01z.json

@@ -57,9 +57,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Add the Sensor (Door/Window detector) to Z-Wave Network\n\n1.Remove the sensor cover. \n\n2.Make sure the sensor is powered. \n\n3.Set Z-Wave controller or Z-Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) \n4.Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times.",
-		"exclusion": "Delete the Sensor (Door/Window detector) from Z-Wave Network\n\n1.Remove the device cover. \n\n2.Make sure the sensor is powered. \n\n3.Set Z-Wave controller or Z-Wave gateway into exclusion mode (Refer to the controller or gateway operating manual) \n4.Press the button three times within 1.5 second, the device will enter exclusion mode.",
-		"reset": "Note: to use the reset procedure only when the primary controller is missing or inoperable.\n\nRestore the Sensor (Door/Window detector) to Factory Default Settings\n\nReset procedure will delete all information on the Z-Wave network and Z-Wave controller or Z-Wave Gateway, and restore the sensor to factory default settings.\n1.Remove the device cover. \n\n2.Make sure the sensor is powered. \n\n3.Press and hold the button for 10 seconds, \n\n4.Release the button.",
+		"inclusion": "1. Remove the sensor cover.\n2. Make sure the sensor is powered.\n3. Press the button three times within 1.5 seconds. LED will flash on and off alternately 5 times.",
+		"exclusion": "1. Remove the device cover.\n2. Make sure the sensor is powered.\n3. Press the button three times within 1.5 seconds.",
+		"reset": "1. Remove the device cover.\n2. Make sure the sensor is powered.\n3. Press and hold the button for 10 seconds.\n4. Release the button.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2717/ne-nas-ds01z%20-%20Zipato%20Door%20Sensor%20User%20Manual%201.1.pdf"
 	}
 }

package/config/devices/0x0131/ne_nas_ab02z.json

@@ -160,9 +160,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The indoor siren can be included to the Z-Wave network by pressing the code button.\n1) Disassemble the siren and insert the battery into\nthe siren. Make sure the device is located within\nthe direct range of the controller.\n2) Set the controller into the inclusion mode (see\nmain controller's operating manual).\n3) Quickly triple click the code button, LED light will\nflash red for 5 times.\n4) The Indoor siren will be detected and included\nin the Z-Wave network.\n5) Wait for the main controller to configure the siren.\n\nSMART START. This product also supports Z-Wave Smart Start option which enables easier inclusion. QR code for SmartStart inclusion is printed on the battery cover. SmartStart option is only possible when network controller is also supporting SmartStart",
-		"exclusion": "1) Make sure the siren is connected to power source. 2) Set the main controller into the exclusion mode\n(see main controller's operating manual).\n3) Quickly triple click the code button, LED light\nwill flash red for 5 times\n4) Wait for the main controller to remove the sensor",
-		"reset": "Reset procedure will remove all information on the Z-Wave network or Z-Wave controller and restore the sensor to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\n1) Remove the sensor's cover\n2) Make sure the sensor is connected to power source \n3) Press the code button for 10 seconds, LED will flash blue for 3 seconds\n4) Release the code button\n\nNote: \nWhen the siren is being restored to factory settings, please make sure power source is connected.",
+		"inclusion": "1. Disassemble the siren and insert the battery.\n2. Quickly triple-click the code button. LED will flash red 5 times.",
+		"exclusion": "1. Make sure the siren is connected to power.\n2. Quickly triple-click the code button. LED will flash red 5 times.",
+		"reset": "1. Remove the sensor's cover.\n2. Make sure the sensor is connected to power.\n3. Press the code button for 10 seconds. LED will flash blue for 3 seconds.\n4. Release the code button.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3046/ne-nas-ab02z.eu%20-%20Zipato%20INDOOR%20SIREN-waveEU_UserManual_v1.3.pdf"
 	}
 }

package/config/devices/0x0131/vs-zd2301.json

@@ -68,9 +68,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-WaveTM Interface Controller into\n'inclusion' mode, and following its instruction to add the ZD2301 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "Put the Z-WaveTM Interface\nController into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
-		"reset": "All user and network settings will be cleared and the device reset to factory\ndefaults when the device is excluded.\n\nPlease use this procedure only in the event if the network\ncontroller is missing or is otherwise inoperable",
+		"inclusion": "Press the program switch to send the NIF.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "All user and network settings will be cleared when the device is excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2346/zp2301.pdf"
 	}
 }

package/config/devices/0x0131/zb_zw_g.json

@@ -25,7 +25,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "* Navigate to Z-Wave network management tools\n* Click the 'Z-WAVE RESET' button and follow onscreen instructions",
+		"reset": "1. Navigate to Z-Wave network management tools.\n2. Click the 'Z-WAVE RESET' button and follow onscreen instructions.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1409/Zipato%20Z-Wave%20User%20Manual%2021.07.2015%20-%20144DPI.pdf"
 	}
 }

package/config/devices/0x0133/pgzng1-2adnas.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "To reset the device, press and hold the reset button on the back of the unit for about 15 seconds. The unit will then restart",
+		"reset": "Press and hold the reset button on the back of the unit for about 15 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3106/Z-Wave%20Plus%20Guide.pdf"
 	}
 }

package/config/devices/0x0136/sl-1500.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1. Click the customize button on the upper right-hand corner of the mashup. \n2. Click Select App.\n3. Select the proper application.\n4. As list of gateways appear on the Gateways mashup, click the Manage Gateways button. \n5. In the lower left-hand corner, press the Factory Reset button.\n6. Confirm the factory reset.",
+		"reset": "1. Click the customize button on the upper right-hand corner of the mashup.\n2. Click Select App.\n3. Select the proper application.\n4. As list of gateways appear on the Gateways mashup, click the Manage Gateways button.\n5. In the lower left-hand corner, press the Factory Reset button.\n6. Confirm the factory reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1275/SysLINK%201000%20User%20Guide%20-%20Z-Wave%20Market%20Certification.docx"
 	}
 }

package/config/devices/0x0138/smco400.json

@@ -50,9 +50,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "ADDING ALARM\n1. Slide battery door open.\n2. Insert batteries checking the correct orientation.\n3. Press and hold the test button with your finger or thumb. Keep it held down as you slide the battery drawer closed. You may then release the button.\nNOTE: Use only your finger or thumb on the test button. The use of any other instrument is strictly prohibited",
-		"exclusion": "REMOVING ALARM\n1. Slide battery door open.\n2. Remove and re-insert batteries checking the correct orientation.\n3. Press and hold the test button with your finger or thumb. Keep it held down as you slide the battery drawer closed. You may then release the button.\nNOTE: Use only your finger or thumb on the test button. The use of any other instrument is strictly prohibited",
-		"reset": "RESETTING ALARM\nIf the device is powered up with the test button held down for 10+ seconds, the device will reset all Z-Wave settings and leave the network.\nUpon completion of the Reset operation, the LED will glow and the horn will sound for ~1 second.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Slide battery door open.\n2. Insert batteries checking the correct orientation.\n3. Press and hold the test button with your finger or thumb.\n4. Keep it held down as you slide the battery drawer closed.\n5. Release the button.",
+		"exclusion": "1. Slide battery door open.\n2. Remove and re-insert batteries checking the correct orientation.\n3. Press and hold the test button with your finger or thumb.\n4. Keep it held down as you slide the battery drawer closed.\n5. Release the button.",
+		"reset": "Press and hold the test button for 10+ seconds while powering up the device. Upon completion of the Reset operation, the LED will glow and the horn will sound for ~1 second.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4087/User_Manual_M08-0456-170694.pdf"
 	}
 }

package/config/devices/0x0138/zcombo-g.json

@@ -53,10 +53,10 @@
 		}
 	],
 	"metadata": {
-		"wakeup": "WAKEUP\n1. Slide battery door open and then closed with the batteries inserted.",
-		"inclusion": "ADD\n1. Slide battery door open.\n2. Insert batteries checking the correct orientation.\n3. Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button.\nNOTE: Use only your finger or thumb on the test button. The use of any other instrument is strictly prohibited",
-		"exclusion": "REMOVE\n1. Slide battery door open.\n2. Remove and re-insert batteries checking the correct orientation.\n3. Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button.\nNOTE: Use only your finger or thumb on the test button. The use of any other instrument is strictly prohibited",
-		"reset": "RESET DEVICE\nIf the device is powered up with the test button held down for 10+ seconds, the device will reset all Z-Wave settings and leave the network.\nUpon completion of the Reset operation, the LED will glow and the horn will sound for ~1 second.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"wakeup": "Slide battery door open and then closed with the batteries inserted.",
+		"inclusion": "1. Slide battery door open.\n2. Insert batteries checking the correct orientation.\n3. Press and hold the test button.\n4. Keep it held down as you slide the battery drawer closed.\n5. Release the button.",
+		"exclusion": "1. Slide battery door open.\n2. Remove and re-insert batteries checking the correct orientation.\n3. Press and hold the test button.\n4. Keep it held down as you slide the battery drawer closed.\n5. Release the button.",
+		"reset": "Press and hold the test button for 10+ seconds while powering up the device. Upon completion of the Reset operation, the LED will glow and the horn will sound for ~1 second.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3886/User_Manual_M08-0456-173833_D2.pdf"
 	}
 }

package/config/devices/0x013c/nsg-ab-02.json

@@ -96,6 +96,6 @@
 	"metadata": {
 		"inclusion": "Press the On/Off button three times within 2 seconds.",
 		"exclusion": "Press the On/Off button three times within 2 seconds.",
-		"reset": "1. Press the On/Off button three times within 2 seconds\n2. Within 1 second, press the On/Off button again for 5 seconds"
+		"reset": "1. Press the On/Off button three times within 2 seconds.\n2. Within 1 second, press the On/Off button again for 5 seconds."
 	}
 }

package/config/devices/0x013c/pac01.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "Press the Include button three times within 2 seconds.",
 		"exclusion": "Press the Include button three times within 2 seconds.",
-		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
+		"reset": "1. Press the Include button three times within 2 seconds.\n2. Within 1 second, press the Include button again for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3619/PAC01_UserManual.pdf"
 	}
 }

package/config/devices/0x013c/pad07.json

@@ -36,7 +36,7 @@
 		{
 			"#": "2",
 			"label": "LED Indication Mode",
-			"description": "1. show dimmer state：when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode：when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
+			"description": "1. show dimmer state: when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode: when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
 			"valueSize": 1,
 			"unit": "seconds",
 			"defaultValue": 1,
@@ -59,7 +59,7 @@
 		{
 			"#": "3",
 			"label": "External Switch Type",
-			"description": "1. one switch mode：only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode：s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode：s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
+			"description": "1. one switch mode: only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode: s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode: s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -104,7 +104,7 @@
 	"metadata": {
 		"inclusion": "Press the Include button three times within 2 seconds.",
 		"exclusion": "Press the Include button three times within 2 seconds.",
-		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
+		"reset": "1. Press the Include button three times within 2 seconds.\n2. Within 1 second, press the Include button again for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2356/PAD07-A1%20manual-20170413.pdf"
 	}
 }

package/config/devices/0x013c/pad09.json

@@ -46,7 +46,7 @@
 	"metadata": {
 		"inclusion": "Press the Include button three times within 2 seconds.",
 		"exclusion": "Press the Include button three times within 2 seconds.",
-		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
+		"reset": "1. Press the Include button three times within 2 seconds.\n2. Within 1 second, press the Include button again for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3142/PAD09_UserManual_Philio.pdf"
 	}
 }

package/config/devices/0x013c/pan15-1-nes.json

@@ -91,7 +91,7 @@
 		{
 			"#": "9",
 			"label": "Rf Off Command Mode",
-			"description": "Whenever a switch off command, basic_set、binary_switch_set、switch_all_off, is received, it could be interpreted as 4 variety of commands.  1.switch off：it switches to off state. the default setting is switch off.  2.ignore：the switch off command will be ignored.  3.switch toggle：it switches to the inverse of current state.  4.switch on：it switches to on state",
+			"description": "Whenever a switch off command, basic_set、binary_switch_set、switch_all_off, is received, it could be interpreted as 4 variety of commands.  1.switch off: it switches to off state. the default setting is switch off.  2.ignore: the switch off command will be ignored.  3.switch toggle: it switches to the inverse of current state.  4.switch on: it switches to on state",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,

package/config/devices/0x013c/pan26.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press the middle button (button ⑤) three times within 2 seconds.",
-		"exclusion": "Press the middle button (button ⑤) three times within 2 seconds.",
-		"reset": "Press and hold the middle button (button ⑤) four times, keeping it held on the 4th press for 3-10 seconds, then release.",
+		"inclusion": "Press the middle button three times within 2 seconds.",
+		"exclusion": "Press the middle button three times within 2 seconds.",
+		"reset": "Press and hold the middle button four times, keeping it held on the 4th press for 3-10 seconds, then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3603/PAN26%20manual-20190806.pdf"
 	}
 }

package/config/devices/0x013c/pan34.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press the Include Button three times within 2 seconds.",
-		"exclusion": "Press the Include Button three times within 2 seconds.",
-		"reset": "1. Press the Include Button three times within 2 seconds\n2. Within 1 second, press the On/Off button for 5 seconds",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the On/Off button for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4250/PAN34%20manual-20210713.pdf"
 	}
 }

package/config/devices/0x013c/psc03.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Click Reset Gateway to reset the Z-Wave controller.",
+		"reset": "Click the Reset Gateway button.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2964/PSC03%20Gateway%20User%20ManualV1.1_20180613.pdf"
 	}
 }

package/config/devices/0x013c/psm09.json

@@ -28,8 +28,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press the tamper key three times within 3 seconds. If successful, the LED will flash slowly.",
-		"exclusion": "Press the tamper key three times within 3 seconds. If successful, the code light will flash for 30 seconds.",
+		"inclusion": "Press the tamper key three times within 3 seconds.",
+		"exclusion": "Press the tamper key three times within 3 seconds.",
 		"reset": "1. Press the button three times in three seconds\n2. The LED will flash slowly for one second\n3. Press and hold the button until the LED lights up\n4. After about three seconds, the LED will turn off\n5. Release the button within two seconds\nIf successful, the LED will flash once per second.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3462/PSM09_UserManual_0624.pdf"
 	}

package/config/devices/0x013c/psr03-b.json

@@ -121,7 +121,7 @@
 	"metadata": {
 		"inclusion": "Press the key three times within 1.5 seconds.",
 		"exclusion": "Press the key three times within 1.5 seconds.",
-		"reset": "1. Press and hold the key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the key within 2 seconds after the LED turns off.",
+		"reset": "1. Press and hold the key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the key within 2 seconds after the LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1407/PSR03_ABC_version_Manual.pdf"
 	},
 	"compat": {

package/config/devices/0x013c/psr07.json

@@ -65,7 +65,7 @@
 	"metadata": {
 		"inclusion": "1. Rotate to area A\n2. Press the button three times within 1.5 seconds",
 		"exclusion": "1. Rotate to area A\n2. Press the button three times within 1.5 seconds",
-		"reset": "1. Rotate to area A\n2. Press and hold the button four times within 1.5 seconds, keeping it held on the 4th press until the red LED lights up\n3. Release the button within 2 seconds after the red LED turns off.",
+		"reset": "1. Rotate to area A\n2. Press and hold the button four times within 1.5 seconds, keeping it held on the 4th press\n3. Wait for the red LED to light up for 3 seconds, then turn off\n4. Release the button within 2 seconds after the red LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1988/PSR07_UserManual.pdf"
 	}
 }

package/config/devices/0x013c/pst02-a-br.json

@@ -304,9 +304,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press any tamper key three times within 1.5 seconds.\nNote: There are two tamper keys - one on the back side and one on the front side.",
-		"exclusion": "Press any tamper key three times within 1.5 seconds.\nNote: There are two tamper keys - one on the back side and one on the front side.",
-		"reset": "1. Press and hold any tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off\nNote: There are two tamper keys - one on the back side and one on the front side.",
+		"inclusion": "Press any tamper key three times within 1.5 seconds.",
+		"exclusion": "Press any tamper key three times within 1.5 seconds.",
+		"reset": "1. Press and hold any tamper key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the tamper key within 2 seconds after the LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2625/Manual.pdf"
 	}
 }

package/config/devices/0x013c/pst02a.json

@@ -299,8 +299,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Triple-click the tamper switch within 1.5 seconds.",
-		"exclusion": "Triple-click the tamper switch within 1.5 seconds.",
-		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off."
+		"inclusion": "Press the tamper switch three times within 1.5 seconds.",
+		"exclusion": "Press the tamper switch three times within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the tamper key within 2 seconds after the LED turns off"
 	}
 }

package/config/devices/0x013c/pst02b.json

@@ -221,8 +221,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Triple-click the tamper switch within 1.5 seconds.",
-		"exclusion": "Triple-click the tamper switch within 1.5 seconds.",
-		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off."
+		"inclusion": "Press the tamper switch three times within 1.5 seconds.",
+		"exclusion": "Press the tamper switch three times within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the tamper key within 2 seconds after the LED turns off"
 	}
 }

package/config/devices/0x0140/fkabz002.json

@@ -15,9 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To add the product to the system, please follow the following steps. \n1. Start the COQON App \n2. Select \"Device\" then \"Settings\" and tap on \"+\" to add your Window Sensor \n3. Select COQON \n4. Follow the steps in the App",
-		"exclusion": "To remove your device from the system, please start the exclusion process to exclude the device from the COQON App. The device will be reset.",
-		"reset": "Factory reset: \n\n1. Remove battery \n2. Hold the Tamper\n3. Insert Battery \n4. Release Tamper within 5 sec. \n\nNote: Please use this procedure only when the primary controller is missing or inoperable!",
+		"reset": "1. Remove battery\n2. Hold the tamper button\n3. Insert battery\n4. Release tamper button within 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3022/FKABZ002New.pdf"
 	}
 }

package/config/devices/0x0140/sc428zw.json

@@ -160,9 +160,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Refer to the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n• Locate the Device Specific Key (DSK) label located on the back(plug side) of the SmartPlug, scan QR code to obtain DSK.\n• Plug the SmartPlug switch into an AC outlet at the desired location to account for any radio interference.\n• Press the Multi Button once to initiate adding the device to the network",
-		"exclusion": "Refer to the instructions for your Z-Wave certified controller to remove a device to the Z-Wave network.\n• Press the Multi Button once to remove the switch from the network",
-		"reset": "Press and hold the Multi Button for more than 10 seconds.\nThe amber LED will be illuminated for 2 seconds while it searches\nfor the network. Please use this procedure only when the network\nprimary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Multi Button once.",
+		"exclusion": "Press the Multi Button once.",
+		"reset": "Press and hold the Multi Button for more than 10 seconds. The amber LED will be illuminated for 2 seconds while it searches for the network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4098/SMC-QG-SC428ZW-20213v1_20210308.pdf"
 	}
 }

package/config/devices/0x0147/razberry7_pro.json

@@ -14,7 +14,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave Serial API SetDefault command is used to reset the RaZberry7 Pro board to factory default settings.",
 		"manual": "https://rus.z-wave.me/drive/?file=24e4716409e82d0e27379e3e5208c8667b99"
 	}
 }