@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x018b/gihg20.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- Run ‘ZW_SET_DEFAULT' in Setting, then click YES of UZB PoP UP\n- Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Run 'ZW_SET_DEFAULT' in Settings, then click YES in the popup.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1841/IoT%20허브%20설명서_20160629_review.pdf"
 	}
 }

package/config/devices/0x018b/gwg-02.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- Run ‘ZW_SET_DEFAULT' in Setting, then click YES of UZB PoP UP\n- Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n- If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Run 'ZW_SET_DEFAULT' in Settings, then click YES in the popup.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2384/GWG-02_User%20Manual_20170516.pdf"
 	}
 }

package/config/devices/0x018b/irhg-01.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- This is the Z-Wave Set Default network operation and a confirmation message appears.\n\n\"If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\"",
+		"reset": "Perform the Z-Wave Set Default network operation and confirm in the popup message.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3290/IRHG-01_User_Manual_new.pdf"
 	}
 }

package/config/devices/0x018c/pm-b400zw-n.json

@@ -63,9 +63,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Plug",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Plug",
-		"reset": "Press the button on the Smart Plug for more than 10 seconds after you plug the Smart Plug into a power outlet will make a Exclusion in the network controller, while the flashing red button LED Smart Plug. And all the variables are initialized.\n\n※ Please use this procedure only in the event that the network primary \n controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Plug into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Plug into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "Plug the Smart Plug into a power outlet and press the button for more than 10 seconds. The red LED will flash and all variables will be initialized.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1870/PB-B400ZWN_Manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-105.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nThe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3315/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-205.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nThe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3314/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-305.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nhe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event thant the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3287/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018e/acgs-23zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n1. Insert the 3V CR123A Lithium battery into the battery compartment connecting the correct polarity as shown on the battery compartment lid.\n2. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n3. Within 1 second, press the Function Button 3 times. \n4. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n5.If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Glass Break Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1 second, press the Function Button 3 times and the Glass Break Detector will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n1. Remove the batteries of the Glass Break Detector first.\n2. Press and hold the Function Button. While holding the Function Button, power on the Glass Break Detector by re-inserting the batteries, wait for 10 seconds to factory reset.\n<NOTE>\n1. Factory resetting the Glass Break Detector will restore it to factory default settings (excluded from the Z-Wave network). The Z-Wave gateway or control panel will still keep its Z-Wave settings. Please refer to the gateway or control panel manual on how to remove the Glass Break Detector's Z-Wave settings.",
+		"inclusion": "Insert the 3V CR123A Lithium battery with correct polarity, then press the Function Button 3 times within 1 second.",
+		"exclusion": "Press the Function Button 3 times within 1 second. The Glass Break Detector will be removed from the Z-Wave network.",
+		"reset": "1. Remove the batteries from the Glass Break Detector\n2. Press and hold the Function Button\n3. While holding the Function Button, re-insert the batteries and wait for 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3240/ACGS-23ZW-(OTA)%2020190124%20S2認證.pdf"
 	}
 }

package/config/devices/0x018e/bx-32zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n - Insert the two 1.5V D-Cell alkaline batteries into the battery \n compartment connecting the correct polarity as shown on the\n battery compartment lid.\n - The Bellbox will emit a 2-tone beep.\n Put the Z-Wave gateway or control panel into Inclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n - Within 1.5 seconds, press the Function Button 3 times.\n - Refer to the operation manual of the Z-Wave Gateway or Control \n Panel to complete the adding process.\n - If the sensor has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the sensor is unable to be added into \n the current Z-Wave Gateway/Control Panel, please exclude it first \n (see Removing Device) before attempting to include it into the \n current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Bellbox must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n - Put the Z-Wave gateway or control panel into Exclusion mode \n (please refer to the Z-Wave gateway or control panel manual).\n - Within 1.5 seconds, press the Function Button 3 times and the \n Bellbox will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n - Press and hold the Function button of the Bellbox for 10 seconds to \n factory reset with all LED flashes once.\n <NOTE>\n Factory resetting the Bellbox will restore it to factory default \n settings (excluded from the Z-Wave network). The Z-Wave gateway \n or control panel will still keep its Z-Wave settings. Please refer to \n the gateway or control panel manual on how to remove the \n Bellbox's Z-Wave settings.",
+		"inclusion": "1. Insert two 1.5V D-Cell alkaline batteries with correct polarity\n2. The Bellbox will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Bellbox will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function button for 10 seconds. All LEDs will flash once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2156/BX-32ZW_20161229.docx"
 	}
 }

package/config/devices/0x018e/bx-35zw.json

@@ -55,9 +55,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Insert the two 1.5V D-Cell alkaline batteries into the battery \n compartment connecting the correct polarity as shown on the \n battery compartment lid.The Bellbox will emit a 2-tone beep.\n -Put the Z-Wave gateway or control panel into Inclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to the operation manual of the Z-Wave Gateway or Control \n Panel to complete the adding process.\n -If the sensor has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the sensor is unable to be added into the \n current Z-Wave Gateway/Control Panel, please exclude it first (see \n Removing Device) before attempting to include it into the current Z-\n Wave Gateway/Control Panel.",
-		"exclusion": "The Bellbox must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\n -Put the Z-Wave gateway or control panel into Exclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the Bellbox \n will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n -Press and hold the Function button of the Bellbox for 10 seconds to \n factory reset with all LED flashes once.\n<NOTE>\n -Factory resetting the Bellbox will restore it to factory default \n settings (excluded from the Z-Wave network). The Z-Wave gateway or \n control panel will still keep its Z-Wave settings. Please refer to the \n gateway or control panel manual on how to remove the Bellbox's Z-\n Wave settings.",
+		"inclusion": "1. Insert two 1.5V D-Cell alkaline batteries with correct polarity\n2. The Bellbox will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Bellbox will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function button for 10 seconds. All LEDs will flash once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2431/BX-35-ZW_20170508.pdf"
 	}
 }

package/config/devices/0x018e/clmt-1zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Plug in the AC Input cable into the socket to power on the Clamp \n Meter.\n -Put the Control Panel into Inclusion mode (please refer to the Z-\n Wave control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to the operation manual of Z-Wave Gateway or Control Panel \n to complete the adding process.\n -If the device has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the device is unable to be added into \n the current Z-Wave Gateway/Control Panel, try removing it first (see \n Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n -Put the Z-Wave Gateway or Control Panel into Exclusion mode \n (please refer to the Z-Wave or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the \n device will be removed from the Z-Wave network.",
-		"reset": "Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave Gateway or Control Panel is lost or otherwise inoperable.\n -Press and hold the Function Button of the device for 10 seconds to \n factory reset.",
+		"inclusion": "Plug the AC Input cable into the socket to power on the Clamp Meter, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2255/CLMT-1ZW%2020170301.docx"
 	}
 }

package/config/devices/0x018e/co-8zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n- Insert the 3 'AA' batteries into the battery compartment connecting the correct polarity as shown on the battery compartment lid. CO-8 will emit a 2-tone beep.\n- Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times. CO-8 will emit a 2-tone beep.\n- Refer to the operation manual of the Z-Wave gateway/Control panel to complete the learn-in process.\n- If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Carbon Monoxide Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n- Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times and the Carbon Monoxide Detector will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n- Remove the batteries of the Carbon Monoxide Detector first.\n- Press and hold the Test Button. While holding the Test Button, power on the Heat Detector by re-inserting the batteries, wait for 10 seconds to factory reset.",
+		"inclusion": "1. Insert 3 AA batteries into the battery compartment with correct polarity\n2. CO-8 will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds\n4. CO-8 will emit another 2-tone beep",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Carbon Monoxide Detector will be removed from the Z-Wave network.",
+		"reset": "1. Remove the batteries from the Carbon Monoxide Detector\n2. Press and hold the Test Button\n3. While holding the Test Button, re-insert the batteries\n4. Wait for 10 seconds to complete factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2075/CO-8ZW_20161109.docx"
 	}
 }

package/config/devices/0x018e/dc-15zw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Pull out the battery insulator.\n-The LED indicator will turn on briefly.\n-Put the Z-wave gateway or control panel into Inclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times.\n-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.\n-Please press and release the Tamper Switch once, and activate the Door Contact once (open and close) after inclusion is completed to ensure the Gateway/Control Panel recognizes the current status of the Door Contact.\n-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.",
-		"exclusion": "The Door Contact must be removed from existing Z-wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Door Contact will be removed from the Z-wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Door Contact for 10 seconds to factory reset.",
+		"inclusion": "1. Pull out the battery insulator\n2. The LED indicator will turn on briefly\n3. Press the Test Button 3 times within 1.5 seconds\n4. Press and release the Tamper Switch once\n5. Activate the Door Contact once (open and close)",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Door Contact will be removed from the Z-wave network.",
+		"reset": "Press and hold the Test Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1429/DC-15ZW_20150806.doc"
 	}
 }

package/config/devices/0x018e/dc-23zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Pull out the battery insulator; this will connect the battery to power on the Door Contact.\n\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (Please refer to the Z-Wave Gateway or Control Panel manual).\n\n3. Press the Function button 3 times within 1.5 seconds.\n\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete adding process.\n\n5. If the Door Contact has already been added (included) into another Z-Wave Gateway/Control Panel, or if the Door Contact is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel",
-		"exclusion": "1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n\n2. Within 1.5 seconds, press the Function Button 3 times and the Door Contact will be removed from the Z-Wave network",
-		"reset": "Press and hold the Function Button of the Door Contact for 10 seconds to factory reset (only use factory reset when network Control Panel/Gateway is missing or inoperable)",
+		"inclusion": "Pull out the battery insulator to power on the Door Contact, then press the Function button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Door Contact will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2542/DC-23ZW%20Manual.pdf"
 	}
 }

package/config/devices/0x018e/emd-1zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Insert batteries to power on the E-meter.\n -Put the Z-Wave control panel into Inclusion mode (please refer to \n the Z-Wave control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to operation manual of the Z-Wave Gateway or Control Panel \n to complete the adding process.\nIf the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n -Put the Z-Wave Gateway or Control Panel into Exclusion mode \n (please refer to the Z-Wave or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the \n device will be removed from the Z-Wave network.",
-		"reset": "Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave Gateway or Control Panel is lost or otherwise inoperable.\n -Press and hold the Function Button of the device for 10 seconds to \n factory reset.",
+		"inclusion": "Insert batteries to power on the E-meter, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2251/EMD-1ZW%2020170218.pdf"
 	}
 }

package/config/devices/0x018e/hd-9zw.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Insert the 3 'AA' batteries into the battery compartment connecting the correct polarity as shown on the battery compartment lid.\n-HD-9 will emit a 2-tone beep.\n-Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times. HD-9 will emit a 2-tone beep.\n-Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n-If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Heat Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Heat Detector will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Heat Detector.\n-While holding the Test Button, power on the Heat Detector, wait for 10 seconds to factory reset.",
+		"inclusion": "1. Insert 3 AA batteries into the battery compartment with correct polarity\n2. HD-9 will emit a 2-tone beep\n3. Press the Test Button 3 times within 1.5 seconds\n4. HD-9 will emit another 2-tone beep",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Heat Detector will be removed from the Z-Wave network.",
+		"reset": "1. Press and hold the Test Button\n2. While holding the Test Button, power on the Heat Detector\n3. Wait for 10 seconds to complete factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1427/HD-9ZW%2020150911.doc"
 	}
 }

package/config/devices/0x018e/ir-16zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n- Pull out the battery Insulator steadily.\n- The LED indicator will flash for 30 seconds (The PIR is warming up). During the warm up period, the PIR will not be activated. It is recommended that you stay away from the detection area during this time. After the warming period is over, the LED will turn off and the PIR will be ready for operation.\n- Put the Z-Wave control panel into Inclusion mode (please refer to the Z-Wave control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times.\n- Refer to the operation manual of the Z-Wave gateway or control panel to complete the adding process.\n- Please press and release the Tamper Switch once after inclusion is completed to ensure the Gateway/Control Panel recognizes the current Tamper condition.\n- If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n- Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\nFactory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave gateway or control panel is lost or otherwise inoperable.\n- Press and hold the Function Button of the device for 12 seconds to factory reset.",
+		"inclusion": "1. Pull out the battery insulator\n2. The LED will flash for 30 seconds while the PIR warms up\n3. After the LED turns off, press the Function Button 3 times within 1.5 seconds\n4. Press and release the Tamper Switch once after inclusion",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 12 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2076/IR-16SLZW_IRP-16SLZW_20161109.doc"
 	}
 }

package/config/devices/0x018e/lm-1zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": " Put the Z-Wave gateway or control panel into Inclusion mode (please refer to the Z-Wave gateway or control panel manual).\n Within 1.5 seconds, press the Function Button 3 times.\n Refer to the operation manual of the Z-Wave gateway or control panel to complete the adding process.\n If the Sensor has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": " Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n Within 1.5 seconds, press the Function Button 3 times and the Sensor will be removed from the Z-Wave network, the LED will light on for 1 second to indicate.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable)\n Remove the battery of the Sensor first.\n Press and hold the Function Button. While holding the Function Button, power on the Sensor by re-inserting the battery, wait for 10 seconds to factory reset, the LED will light on for 1 second to indicate.",
+		"inclusion": "Press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The LED will light for 1 second to indicate removal.",
+		"reset": "1. Remove the battery from the Sensor\n2. Press and hold the Function Button\n3. While holding the Function Button, re-insert the battery and wait for 10 seconds\n4. The LED will light for 1 second to indicate factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2485/LM-1ZW_20170608.pdf"
 	}
 }

package/config/devices/0x018e/psm-29zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Plug the Power Switch Meter into a power outlet.\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete the adding process.\n5. If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "1. Put the Z-Wave Gateway or Control Panel into Exclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "*. Press and hold the Function Button of the device for 10 seconds to factory reset.\n1. Factory resetting the device will restore it to factory default settings (excluded from the Z-Wave network). The Z-Wave Gateway or Control Panel will still keep its Z-Wave settings. Please refer to the Gateway or Control Panel manual on how to remove the device's Z-Wave settings.\n2. Factory resetting the device will also clear all accumulated power data.\n3. Before you remove or factory reset the Power Switch Meter, please ensure that the device DSK information has been removed or does not exist in the gateway. If you remove or factory reset the device, but its DSK still exists in the gateway, the gateway will automatically include the device again.",
+		"inclusion": "Plug the Power Switch Meter into a power outlet, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds. This will clear all accumulated power data.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3747/PSM-29ZW_S2SmartStart_20191219.pdf"
 	}
 }

package/config/devices/0x018e/psm-din2-zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Connect the external power supply to the input connector and external devices to the output connector.\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control panel to complete the adding process.\n5. If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "1. Put the Z-Wave Gateway or Control Panel into Exclusion mode (please refer to the Z-Wave Gateway or Control panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n#. Press and hold the Function Button of the device for 10 seconds to factory reset.",
+		"inclusion": "Connect the external power supply to the input connector and external devices to the output connector, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3824/PSM-DIN2-ZW_%20S2_SmartStart_20200320.pdf"
 	}
 }

package/config/devices/0x018e/psm-din3-zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Connect the external power supply to the input connector and external devices to the output connector.\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control panel to complete the adding process.\n5. If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n*. Press and hold the Function Button of the device for 10 seconds to factory reset",
+		"inclusion": "Connect the external power supply to the input connector and external devices to the output connector, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3864/PSM-DIN3-ZW-S2_SmartStart_20200423.pdf"
 	}
 }

package/config/devices/0x018e/pss-29zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Classic Inclusion\n1. Plug the Power Switch into a power outlet.\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete the adding process.\n5. If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The device must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n1. Put the Z-Wave Gateway or Control Panel into Exclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n#. Press and hold the Function Button of the device for 10 seconds to factory reset.",
+		"inclusion": "Plug the Power Switch into a power outlet, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3782/PSS-29ZW.pdf"
 	}
 }

package/config/devices/0x018e/rmb-35zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Connect the Router into the power socket to power on. \n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete the adding process.\n5. If the sensor has already been added (included) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "1. Put the Z-Wave Gateway or Control Panel into Exclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the Router will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\nPress and hold the Function Button for 10 seconds to factory reset",
+		"inclusion": "Connect the Router to a power socket, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Router will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3787/RMB-35-ZW_2A_20200122.pdf"
 	}
 }

package/config/devices/0x018e/s-2zw.json

@@ -44,9 +44,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n1. Connect the power to Shutter Control (see manual's Installation).\n2. Put the Z-Wave gateway or control panel into Inclusion mode (please refer to the Z-Wave gateway or control panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave gateway or control panel to complete the adding process.\n5. If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\n1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\nFactory resetting the device will restore it to factory default settings (i.e. excluded from Z-Wave network). Please use the reset procedure only when the primary controller is missing or inoperable.\n\nPress and hold the Function Button of the device for 10 seconds to factory reset.",
+		"inclusion": "Connect power to the Shutter Control, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3246/SCM_2_ZW.pdf"
 	}
 }

package/config/devices/0x018e/sd-16zw.json

@@ -29,9 +29,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Function button 3 times. The Smoke Detector will emit a 2-tone beep and the LED will turn on for ~2 seconds.\n-Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n-If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.\n-When the 1-minute warming period is over, the Smoke Detector will start calibration process.",
-		"exclusion": "The Smoke Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Function button 3 times and the Smoke Detector will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Function Button of the Smoke Detector for 10 seconds to factory reset",
+		"inclusion": "Press the Function button 3 times within 1.5 seconds. The Smoke Detector will emit a 2-tone beep and the LED will turn on for ~2 seconds.",
+		"exclusion": "Press the Function button 3 times within 1.5 seconds. The Smoke Detector will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1621/SD-16-ZW%2020160114.doc"
 	}
 }

package/config/devices/0x018e/sd-29.json

@@ -20,9 +20,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Insert three 3V CR123 Lithium batteries into the battery compartment. Orient the battery according to the battery compartment polarity indication before insertion.\n2. After batteries are inserted, the Smoke Detector will sound 2 short beeps, the Red LED will start to flash and initiates a 1-minute warm-up period.\n3. During the 1-minute warming period, you can learn (include) the Smoke Detector into the Panel, refer to Add Device (Inclusion) for details.\n4. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n5. Within 1.5 seconds, press the Function button 3 times. The Smoke Detector will emit a 2-tone beep and the LED will turn on for ~2 seconds. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n6. When the 1-minute warming period is over, one short beep will sound to indicate that the Smoke Detector is starting calibration process. Learning/Inclusion is prohibited during calibration. If the Smoke Detector has not been included in the panel yet, wait for calibration to complete before including the Smoke Detector. The completion of calibration process will be notified by a 2-tone beep and the Red LED will turn off. If the Smoke Detector gives out continuous beeps instead, it indicates that the Smoke Detector has failed the calibration. Remove the battery and restart from step 1 after a pause of at least 30 seconds.\n7. After the warming-up and calibration process, if the Smoke Detector is not learned (included) into the Z-Wave gateway/Control Panel, complete the learning/inclusion process then refer to Installation section below to mount the Smoke Detector.\n8. If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel",
-		"exclusion": "#. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n#. Within 1.5 seconds, press the Function button 3 times and the Smoke Detector will be removed from the Z-wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable.)\n1. Remove the batteries of the Smoke Detector first.\n2. Press and hold the Function button. While holding the Function button, power on the Smoke Detector by re-inserting the batteries, wait for 20 seconds to factory reset.",
+		"inclusion": "1. Insert three 3V CR123 batteries with correct polarity\n2. The Smoke Detector will sound 2 short beeps and Red LED will flash\n3. Wait for the 1-minute warm-up period\n4. Press the Function button 3 times within 1.5 seconds\n5. The Smoke Detector will emit a 2-tone beep and LED will turn on briefly\n6. Wait for calibration to complete (indicated by 2-tone beep and Red LED turning off)",
+		"exclusion": "Press the Function button 3 times within 1.5 seconds. The Smoke Detector will be removed from the Z-wave network.",
+		"reset": "1. Remove the batteries from the Smoke Detector\n2. Press and hold the Function button\n3. While holding the Function button, re-insert the batteries and wait for 20 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3926/SD-29-AC-ZW%20series_2020713.pdf"
 	}
 }

package/config/devices/0x018e/sd-8zw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Insert the 3 'AA' batteries into the battery compartment connecting the correct polarity as shown on the battery compartment lid. The Smoke Detector will emit a 2-tone beep.\n-The LED will start flashing and begin a 6-minute warming period.\n-Put the Z-wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times. The Smoke Detector will emit a 2-tone beep and the LED will turn on for ~2 seconds.\n-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.\n-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.\n-When the 6-minute warming period is over, the Smoke Detector will emit one short beep to indicate that the Smoke Detector is starting calibration process. The process will be repeated every 100 seconds and notified by a short beep respectively. The Smoke Detector will emit a 2-tone beep and the LED will turn off to indicate calibration is completed.\n-Normal calibration process lasts 2 - 16 minutes.\n-If the Smoke Detector emits continuous beeps after 16 minutes, the calibration has failed. Remove the batteries to silence the continuous beeps.\n-Restart the calibration process by re-inserting the batteries.",
-		"exclusion": "The Smoke Detector must be removed from existing Z-wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Smoke Detector will be removed from the Z-wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Smoke Detector for 8 seconds to factory reset",
+		"inclusion": "1. Insert 3 'AA' batteries into the battery compartment with correct polarity\n2. The Smoke Detector will emit a 2-tone beep and LED will start flashing\n3. Wait for the 6-minute warming period to complete\n4. Press the Test Button 3 times within 1.5 seconds\n5. The Smoke Detector will emit a 2-tone beep and LED will turn on briefly\n6. Wait for calibration to complete (2-16 minutes) - indicated by 2-tone beep and LED turning off",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Smoke Detector will be removed from the Z-wave network.",
+		"reset": "Press and hold the Test Button for 8 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1428/SD-8ZW%2020150804.doc"
 	}
 }

package/config/devices/0x018e/sdco.json

@@ -24,9 +24,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Press down on the red tab and insert three new batteries into the compartment. The red tab needs to be in horizontal position underneath the batteries. This is to prevent users from using the SDCO without inserting batteries.\n2. Replace the battery compartment cover and turn the SDCO over. You will hear 'Welcome, Smoke Alarm and Carbon Monoxide Detector', indicating it is ready for further setup (for serial connected models only).\n3. The SDCO allows users to set up a location prompt for an area, to view the full list of locations and setup instructions, please refer to 'Voice Prompt' Section for details. It is recommended to perform warm-up and calibration process before including your device into the Z-Wave coordinator.\n\n<Including to the Z-Wave coordinator>\n1. Put the Z-Wave gateway or control panel into Inclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the button 3 times. The SDCO will emit a 2-tone beep.\n3. Refer to the operation manual of the Z-Wave gateway or control panel to complete the inclusion process.\n4. If the sensor has already been included into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be included into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The SDCO must be removed from existing Z-Wave network before being included into another. \n1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the button 3 times and the SDCO will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n1. Press and hold the button of the SDCO for 20 seconds. Release the button when you hear 3 beeps to perform factory reset.",
+		"inclusion": "1. Press down on the red tab and insert three new batteries with the red tab in horizontal position\n2. Replace the battery compartment cover\n3. You will hear 'Welcome, Smoke Alarm and Carbon Monoxide Detector'\n4. Press the button 3 times within 1.5 seconds\n5. The SDCO will emit a 2-tone beep",
+		"exclusion": "Press the button 3 times within 1.5 seconds. The SDCO will be removed from the Z-Wave network.",
+		"reset": "Press and hold the button for 20 seconds. Release when you hear 3 beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3724/SDCO-1-RhTH-SC-Batt-ZW_191127.pdf"
 	}
 }

package/config/devices/0x018e/srac-23zw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Plug the Siren into a power socket.\n-The LED indicator will flash twice.\n-Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times.\n-Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n-If the Siren was included successfully, it will emit 1 long beep and the LED will flash once.\n-If the device has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the device is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Siren must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Siren will be removed from the Z-Wave network",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Siren for ~10 seconds until the LED starts to flash (twice) to factory reset. The siren will also emit 2 short beeps.",
+		"inclusion": "1. Plug the Siren into a power socket\n2. The LED indicator will flash twice\n3. Press the Test Button 3 times within 1.5 seconds\n4. The Siren will emit 1 long beep and LED will flash once if successful",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Siren will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Test Button for ~10 seconds until the LED starts to flash twice. The siren will emit 2 short beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1755/SRAC-23B-ZW%2020151228.doc"
 	}
 }

package/config/devices/0x018e/wls-23-zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Open the cover by removing the bottom fixing screw (using a Philips screwdriver) on the Water Leak Sensor. \n2. Insert the battery in the battery compartment \n3. Put the Z-Wave gateway or control panel into Inclusion mode (please refer to the Z-Wave gateway or control panel manual). \n4. Within 1.5 seconds, press the Function Button 3 times. \n5. Refer to the operation manual of the Z-Wave gateway or control panel to complete the adding process. \n6. If the sensor has already been added (included) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel. \n7. Reattach the cover to the base and tighten the bottom-fixing screw.",
-		"exclusion": "1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual). \n2. Within 1.5 seconds, press the Function Button 3 times and the Water Leak Sensor will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\nPress and hold the Function Button of the Water Leak Sensor for 10 seconds to factory reset.",
+		"inclusion": "1. Open the cover by removing the bottom fixing screw\n2. Insert the battery in the battery compartment\n3. Press the Function Button 3 times within 1.5 seconds\n4. Reattach the cover and tighten the fixing screw",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Water Leak Sensor will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3594/WLS-23-ZW_20190612.pdf"
 	}
 }

package/config/devices/0x018e/ws-15zw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Open the cover by removing the bottom fixing screw (using a Philips screwdriver) on the Water Sensor.\n-Insert the battery in the battery compartment\n-Put the Z-wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times.\n-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.\n-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.\n-Reattach the cover to the base and tighten the bottom-fixing screw.",
-		"exclusion": "The Water sensor must be removed from existing Z-wave network before being included into another. There are two methods available to exclude a device:\nExclusion Mode\n-Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Water sensor will be removed from the Z-wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Water sensor for 12 seconds to factory reset",
+		"inclusion": "1. Open the cover by removing the bottom fixing screw\n2. Insert the battery in the battery compartment\n3. Press the Test Button 3 times within 1.5 seconds\n4. Reattach the cover and tighten the fixing screw",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Water sensor will be removed from the Z-wave network.",
+		"reset": "Press and hold the Test Button for 12 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1430/WS-15ZW%2020150804.doc"
 	}
 }

package/config/devices/0x018f/zme_wallc-s.json

@@ -329,9 +329,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Place your primary controller in inclusion mode by following the manufacturer's instructions, then activate inclusion on the wall controller by pressing any one of the four buttons for one second. Inclusion mode is indicated by the red/green blinking of the LEDs until the timeout occurs after 10 seconds",
-		"exclusion": "Re-Inclusion and Exclusion are performed by pushing button 1 in management mode. Pushing all four buttons for 5 sec. turns the device into management mode (indicated by blinking green LED)",
-		"reset": "Use this procedure only if the primary controller is missing or otherwise inoperable. \n(1) Turn the device into Management Mode by keeping all four buttons pushed for 5 seconds, (2) click on Button 3, (3) keep button 4 pushed for 4 seconds",
+		"inclusion": "Press any one of the four buttons for one second. Inclusion mode is indicated by the red/green blinking of the LEDs until the timeout occurs after 10 seconds.",
+		"exclusion": "Push all four buttons for 5 seconds to turn the device into management mode (indicated by blinking green LED), then push button 1 in management mode.",
+		"reset": "1. Turn the device into management mode by keeping all four buttons pushed for 5 seconds\n2. Click on button 3\n3. Keep button 4 pushed for 4 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1086/ZME_WALLC-S-Manual.pdf"
 	}
 }