@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x010a/vitrum_satellite_vi.json

@@ -41,8 +41,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset."
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete."
 	}
 }

package/config/devices/0x010b/dn3g6ja069.json

@@ -119,8 +119,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2852/UsersGuide%20DN3G6JA069%20rev1.pdf"
 	}

package/config/devices/0x010b/dn3g6ja082.json

@@ -35,8 +35,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2979/UsersGuide%20DN3G6JA082%20rev1.pdf"
 	}

package/config/devices/0x010b/dn3g6ja084.json

@@ -35,8 +35,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2980/UsersGuide%20DN3G6JA084%20rev1.pdf"
 	}

package/config/devices/0x010e/danalock_v3-btze.json

@@ -106,9 +106,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Push the switch once. Wait 5 seconds",
-		"exclusion": "Push the switch once. Wait 5 seconds",
-		"reset": "Push the switch ten times",
+		"inclusion": "Push the switch once.",
+		"exclusion": "Push the switch once.",
+		"reset": "Push the switch ten times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4295/Danalock_V3_Product_manual_Z_Wave_V_0.9.5.pdf"
 	}
 }

package/config/devices/0x010f/fgbs222.json

@@ -398,8 +398,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful adding will be confirmed by the LED indicator.",
-		"exclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful removing will be confirmed by the LED indicator.",
+		"inclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.",
+		"exclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.",
 		"reset": "1. Press and hold the button to enter the menu.\n2. Release button when the device glows yellow.\n3. Quickly click the button to confirm.\n4. After few seconds the device will be restarted, which is signalled with the red colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4153/FGBS-222-T-EN-1.2.pdf"
 	}

package/config/devices/0x010f/fgpb101.json

@@ -449,8 +449,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
-		"exclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
+		"inclusion": "Click the Button at least six times.",
+		"exclusion": "Click the Button at least six times.",
 		"reset": "1. Click the Button exactly five times.\n2. Press and hold the Button for at least 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3486/tech_panic_en_9.pdf"
 	}

package/config/devices/0x010f/fgr-224.json

@@ -257,8 +257,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times.\n4. LED indicator will blink yellow.\n5. Successful adding will be confirmed by the device's LED indicator: Green (non-secure, S0, S2 non-authenticated), Magenta (Security S2 Authenticated), Red (not successful).",
-		"exclusion": "1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device.\n4. Successful removing will be confirmed by the device's LED indicator - Red.",
+		"inclusion": "1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times.\n4. LED indicator will blink yellow.\n5. LED indicator will show: Green (non-secure, S0, S2 non-authenticated), Magenta (Security S2 Authenticated), Red (not successful).",
+		"exclusion": "1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device.\n4. LED indicator will turn red if unsuccessful.",
 		"reset": "1. Switch off the mains voltage (disable the fuse).\n2. Remove the device from the wall switch box.\n3. Switch on the mains voltage.\n4. Press and hold the PROG button to enter the menu.\n5. Wait for the LED indicator to glow yellow.\n6. Quickly release and click the PROG button again.\n7. During the factory reset, the LED indicator will blink yellow.\n8. After few seconds the device will be restarted, which is signalled with the red LED indicator colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/948/FGR-224-T-EN-v1.22.pdf"
 	}

package/config/devices/0x0123/ne-ssen.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Push \"Add/Remove Button\" of this equipment for a short time.\nAlso, if this equipment is NOT Added to any network, it is enable to Add automatically when the battery is connected",
-		"exclusion": "Push \"Add/Remove Button\" of this equipment for a short time",
-		"reset": "Push and hold \"Add/Remove Button\" for a few seconds more than 5 seconds.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Push the Add/Remove button for a short time.",
+		"exclusion": "Push the Add/Remove button for a short time.",
+		"reset": "Push and hold the Add/Remove button for more than 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2177/NE-SSEN_user_manual_ref2.pdf"
 	}
 }

package/config/devices/0x0123/smart-bridge_c3.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Hold down the hardware INIT SW (over 3 seconds). A button on the GUI is present to start the reset(\"Resets the Chip\" button).\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Hold down the hardware INIT switch for over 3 seconds. Press 'Reset the Chip' in the GUI.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2581/InstructionManual_3GGW_20170925.pdf"
 	}
 }

package/config/devices/0x0123/smart-bridge_cl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Hold down the hardware INIT SW (over 3 seconds). A button on the GUI is present to start the reset(\"Resets the Chip\" button).\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Hold down the hardware INIT switch for over 3 seconds. Press 'Reset the Chip' in the GUI.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2579/InstructionManual_LANGW_20170925.pdf"
 	}
 }

package/config/devices/0x0127/738zpl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "The 738Zplus can perform a Factory Default Reset by initializing defaults in the panel programming menu. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Perform a Factory Default Reset by initializing defaults in the panel programming menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2636/LT-1608%20zwave%20certification.pdf"
 	}
 }

package/config/devices/0x0127/xtlpl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use the initialize defaults function to set a panel's programmed memory back to the factory defaults and remove any existing Z-Wave programming. Follow these steps to initialize a panel's defaults:\n1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2685/XTLplus%20zwave%20certification.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrc612-zw3.json

@@ -58,6 +58,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "When lock is reset to factory defaults all Entry Codes\n(including the Master Entry Code*) are deleted and all\nprogramming features are reset to original default\nsettings (see below).\n1. Remove battery cover and batteries.\n2. Remove inside lock to access reset button.\n3. Reset button (see image at right) is located beside\ncable adapter.\n4. While pressing reset button reinstall batteries. Hold\nreset button a minimum of 3 seconds then release.\n5. Replace battery cover.\nAfter reset, Master Entry Code creation is the only\noption available and must be performed prior to\nany other programming of the lock"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the inside lock to access the reset button.\n3. The reset button is located beside the cable adapter.\n4. While pressing the reset button, reinstall the batteries. Hold the reset button for a minimum of 3 seconds, then release.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrc622-zw3.json

@@ -62,6 +62,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrd612-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4644/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrd612-zw3.json

@@ -63,6 +63,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "When lock is reset to factory defaults all Entry Codes\n(including the Master Entry Code*) are deleted and all\nprogramming features are reset to original default\nsettings (see below).\n1. Remove battery cover and batteries.\n2. Remove inside lock to access reset button.\n3. Reset button (see image at right) is located beside\ncable adapter.\n4. While pressing reset button reinstall batteries. Hold\nreset button a minimum of 3 seconds then release.\n5. Replace battery cover.\nAfter reset, Master Entry Code creation is the only\noption available and must be performed prior to\nany other programming of the lock"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the inside lock to access the reset button.\n3. The reset button is located beside the cable adapter.\n4. While pressing the reset button, reinstall the batteries. Hold the reset button for a minimum of 3 seconds, then release.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrd622-zw2.json

@@ -77,9 +77,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4645/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrd622-zw3.json

@@ -62,6 +62,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/ntb610.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1970/nexTouch%20TS%20Manual%20for%20Cert.pdf"
 	}
 }

package/config/devices/0x0129/ntb612-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4643/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntb620.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1857/nexTouch%20TS%20Manual%20for%20Cert.pdf"
 	}
 }

package/config/devices/0x0129/ntb622-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4661/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntb632-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4662/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntb642-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4663/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntm610.json

@@ -85,9 +85,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2966/nexTouchSectionalMortise_ZWavePlusSystemIntegratorsGuide_NTM.pdf"
 	}
 }

package/config/devices/0x0129/ntm612-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4632/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm617-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4633/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm622-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4622/Binder2.pdf"
 	}
 }

package/config/devices/0x0129/ntm625.json

@@ -93,9 +93,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2954/nexTouch%20Sectional%20Mortise%20with%20ZW2.pdf"
 	}
 }

package/config/devices/0x0129/ntm627-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4634/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm632-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4635/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm637-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4636/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm642-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4637/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm647-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4638/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntt610.json

@@ -73,9 +73,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3458/NTT610_620_YaleRealLivingAssureDeadbolt_Z-WavePlus_SystemIntegratorsGuid....pdf"
 	}
 }

package/config/devices/0x0129/ntt612-zw2.json

@@ -80,9 +80,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4664/NTT-2.pdf"
 	}
 }

package/config/devices/0x0129/ntt620-zw2.json

@@ -77,9 +77,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3463/NTT610_620_YaleRealLivingAssureDeadbolt_Z-WavePlus_SystemIntegratorsGuid....pdf"
 	}
 }