@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x0149/wmsr.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press \"Factory Reset\" on the controller Setup menu. \nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\"",
+		"reset": "Press \"Factory Reset\" on the Setup menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2754/WiDom%20Controller%20Quick%20Guide.pdf"
 	}
 }

package/config/devices/0x014a/ddls2-zwave5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when included.",
-		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.",
+		"inclusion": "Press the inclusion / exclusion button on the device. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Press the inclusion / exclusion button on the device.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2781/DDLS2-ZWAVE5_Prod_Rev02.pdf"
 	}
 }

package/config/devices/0x014a/dls-zwave5.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Locate the light switch desired to be used with the Light Switch.\n2. Press the inclusion button on the Light Switch.\n3. The LED on the front of the unit will turn off when included.",
+		"inclusion": "Press the inclusion button on the Light Switch. The LED on the front of the unit will turn off when included.",
 		"exclusion": "Press the inclusion / exclusion button on the Light Switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2164/Ecolink%20Decora%20Light%20Switch%20Z-Wave%20Plus%20Manual.pdf"
 	}

package/config/devices/0x014a/dtls2-zwave5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when network inclusion occurs.",
-		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED in front of the unit will blink steadily when network exclusion occurs.",
+		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED in front of the unit will blink steadily when excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2863/DTLS2-ZWAVE5_Prod_Rev06.pdf"
 	}
 }

package/config/devices/0x014a/dwzwave25.json

@@ -31,8 +31,8 @@
 		"forceNotificationIdleReset": true
 	},
 	"metadata": {
-		"wakeup": "Removing the top case from the sensor will put in device into a tampered mode in which the sensor will stay awake and able to receive messages.",
-		"inclusion": "1. Activate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor.\n2. When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.",
+		"wakeup": "Remove the top case from the sensor to put the device into a tampered mode in which the sensor will stay awake and able to receive messages.",
+		"inclusion": "1. Remove the plastic pull-tab from the back of the sensor.\n2. The LED on the sensor will be solid blue, then go out when inclusion is complete.",
 		"exclusion": "1. Remove the cover of the sensor.\n2. Remove the battery for 10 seconds.\n3. Reinsert the battery and replace the sensor cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1498/D.W.%20Zwave%20Manual%20R1.04.docx"
 	}

package/config/devices/0x014a/ff-zwave5-eco.json

@@ -16,8 +16,8 @@
 	},
 	"metadata": {
 		"inclusion": "Press the learn button for 1 second which is located on the PCB between the LED and the tamper switch. If the LED starts blinking continuously, the sensor was not successfully added.",
-		"exclusion": "Press the learn button located near the LED and Tamper switch. The sensor's LED should blink continuously when removed.",
-		"reset": "1. Put the battery into the sensor.\n2. Do not press the tamper switch.\n3. Hold the learn button down for 10 seconds until the LED turns RED.\n4. Release the learn button and the sensor's green LED will 'breath' on and off continuously.",
+		"exclusion": "Press the learn button located near the LED and tamper switch. The sensor's LED should blink continuously when removed.",
+		"reset": "1. Put the battery into the sensor.\n2. Do not press the tamper switch.\n3. Hold the learn button down for 10 seconds until the LED turns red.\n4. Release the learn button and the sensor's green LED will breathe on and off continuously.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1827/1%20-%20Ecolink%20FireFighter%20Z-wave%20plus%20Manual%20(standard).pdf"
 	}
 }

package/config/devices/0x014a/flf-zwave5_r1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Power up the device to enter inclusion mode. If the LED starts blinking continuously, the sensor was not successfully added. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.",
-		"exclusion": "1. Open the Flood Freeze case and remove the battery for 1 seconds.\n2. Replace the battery.",
-		"reset": "The Flood Freeze sensor factory defaults on network exclusion.",
+		"inclusion": "Power up the device. If the LED starts blinking continuously, the sensor was not successfully added. Remove the battery for 10 seconds if adding fails.",
+		"exclusion": "Open the case and remove the battery for 1 second. Replace the battery.",
+		"reset": "Remove the device from the Z-Wave network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2929/51557%20%20Z-Wave%20FLF%20H214104%20ZWAVE_Ver04.pdf"
 	}
 }

package/config/devices/0x014a/gdzw7-eco.json

@@ -70,9 +70,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Locate and press the hub button on the device. The device will beep and blink green once when added.",
-		"exclusion": "Locate and press the hub button. Device's status indicator will blink red and beep three times when removed.",
-		"reset": "Hold the reset button down for ten seconds. The status indicator will blink red while the reset button is pressed and will go out after ten seconds. The device's status indicator will turn green when the reset operation is complete.",
+		"inclusion": "Press the hub button on the device. The device will beep and blink green once when added.",
+		"exclusion": "Press the hub button. The status indicator will blink red and beep three times when removed.",
+		"reset": "Hold the reset button down for ten seconds. The status indicator will blink red while the reset button is pressed and will go out after ten seconds. The status indicator will turn green when complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/74/GarageDoorControllerUserManualV3.pdf"
 	}
 }

package/config/devices/0x014a/iszw7-eco.json

@@ -88,9 +88,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press the Pair Button (the smaller of the two buttons). During inclusion mode, the Green LED will blink two times every three seconds. When inclusion times-out, the device will blink red and green.",
-		"exclusion": "Press the smaller of the two buttons (Add/Test). The device's red led will come on solid for 1 second when removed.",
-		"reset": "Hold the Pair button for 10 seconds. During the 10 seconds the green LED will flash, and after 10 seconds the red LED will come on solid for 1 second after factory reset.",
+		"inclusion": "Press the Pair Button (the smaller of the two buttons). During inclusion mode, the green LED will blink two times every three seconds. If inclusion times out, the device will blink red and green.",
+		"exclusion": "Press the smaller of the two buttons (Add/Test). The red LED will come on solid for 1 second when removed.",
+		"reset": "Hold the Pair button for 10 seconds. During the 10 seconds the green LED will flash, and after 10 seconds the red LED will come on solid for 1 second.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4000/ISZW7-ECO%20-%20Operation%20Manual%20v9.pdf"
 	}
 }

package/config/devices/0x014a/sc-zwave5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Locate the power outlet desired to be used with the Z-Wave Plus Siren.\n2. Plug in the Z-Wave Siren and verify a single beep sound is heard.\n3. The LED on the front of the unit will turn off when included.",
-		"exclusion": "1. Unplug and re-plug in your Z-Wave Plus Siren.\n2. The device will play a long beep and the LED will begin to breathe when removed.",
+		"inclusion": "1. Plug in the Z-Wave Siren and verify a single beep sound is heard.\n2. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Unplug and re-plug in your Z-Wave Plus Siren. The device will play a long beep and the LED will begin to breathe when removed.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1899/0%20-%20Ecolink%20Siren%20Z-Wave%20Plus%20Manual%20(standard).pdf"
 	}
 }

package/config/devices/0x014a/sdls2-zwave5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when included.",
-		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.",
+		"inclusion": "Press the inclusion/exclusion button. The LED on the front will turn off when successfully included.",
+		"exclusion": "Press the inclusion/exclusion button.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2783/SDLS2-ZWAVE5_Prod_Rev02.pdf"
 	}
 }

package/config/devices/0x014a/stls2-zwave5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off if network inclusion is successful.",
-		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED in front of the unit will blink steadily if the network exclusion is successful.",
+		"inclusion": "Press the inclusion/exclusion button. The LED on the front will turn off if successfully included.",
+		"exclusion": "Press the inclusion/exclusion button. The LED in front will blink steadily if successfully excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2864/STLS2-ZWAVE5_Prod_Rev05.pdf"
 	}
 }

package/config/devices/0x014a/tstat-tbz500.json

@@ -703,8 +703,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Press and hold the FAN button on the Thermostat until the screen changes to the Menu screen.\n2. Press the UP button until ZWAVE is shown in the Status Display line then press Select.\n3. INSTALL should be shown on the status line.\n4. Press the 'Select' button to install.\n5. Press Done on the Thermostat to exit the ZWAVE screen.\n6. Press Done on the Thermostat again to exit the Menu screen.",
-		"exclusion": "1. Press and hold the FAN button for 3 seconds until the Menu screen is displayed.\n2. Press the UP arrow button to scroll to the 'ZWAVE' menu.\n3. Press 'Select' to select the ZWAVE screen.\n4. The display will show 'REMOVE' in the text line.\n5. Press 'Select' to perform the remove action.\n6. Press 'Done' to exit back to the thermostat screen.",
+		"inclusion": "1. Press and hold the FAN button until the Menu screen appears.\n2. Press the UP button until ZWAVE is shown, then press Select.\n3. INSTALL should be shown on the status line.\n4. Press Select to install.\n5. Press Done to exit the ZWAVE screen.\n6. Press Done again to exit the Menu screen.",
+		"exclusion": "1. Press and hold the FAN button for 3 seconds until the Menu screen is displayed.\n2. Press the UP arrow button to scroll to ZWAVE.\n3. Press Select to select the ZWAVE screen.\n4. REMOVE will be shown on the text line.\n5. Press Select to perform the remove action.\n6. Press Done to exit back to the thermostat screen.",
 		"reset": "1. Remove power from the TBZ500.\n2. Restore power to the TBZ500.\n3. When 'TBZ500' appears on the screen, hold down the MODE and FAN buttons at the same time.\n4. Release the buttons when RESET appears on the Status Line.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4093/TBZ500_manual_8_5x5_5_inch__SC_20210325.pdf"
 	}

package/config/devices/0x014d/dkc1000.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "In mobile app, tap \"RESET\" menu.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "In the mobile app, tap RESET menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2024/DKC1000_Manual_Ver0.8%20-%20지웨이브인증용.pdf"
 	}
 }

package/config/devices/0x014d/dkc1001.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Tap \"RESET\" button in controller functions menu\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Tap RESET button in the controller functions menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2642/DK_DKC1001_Ver0.1.pdf"
 	}
 }

package/config/devices/0x014d/ibdk-01.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Please execute this reset procedure only when the primary controller is missing or inoperable.\n1. Open battery cover.\n2. Press and hold the button there\n3. LED is turned on after 5 seconds. Keep holding.\n4. LET starts blinking after 10 seconds.\n5. Release the button when the LED blinks",
+		"reset": "Open battery cover. Press and hold the button until the LED starts blinking after 10 seconds, then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3209/UVA01A_Manual_20190111.pdf"
 	}
 }

package/config/devices/0x014d/ss302.json

@@ -25,7 +25,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "In setting app, enter into following menu.\n\"About Enblink > Factory reset\"\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "In the setting app, enter the following menu: About Enblink > Factory reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2023/Manual.pdf"
 	}
 }

package/config/devices/0x014f/2gig-gc2.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "using UI, \"Reset Controller\" under Z-Wave toolbox (Advanced)",
+		"reset": "Using the UI, select Reset Controller under Z-Wave toolbox (Advanced).",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3687/10022313%20A%20-%202GIG-GC2E%20CONTORL%20PANEL%20USER%20GUIDE_WEB-compressed.pdf"
 	}
 }

package/config/devices/0x014f/el-sc-100.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1. Navigation to the Communication Device: ELAN Z-Wave Network page under Security, Climate, Lighting or\nInput/Output Tabs in Configurator 2. Management View: Network Management 3. Network Action: Reset 4.\nExecute (button to right of Network action)",
+		"reset": "1. Navigate to the 'Communication Device: ELAN Z-Wave Network' page under Security, Climate, Lighting or Input/Output Tabs in Configurator.\n2. Management View: Network Management.\n3. Network Action: Reset.\n4. Click Execute button to the right of Network action.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4083/10024525_Rev-B_Literature_Quick_Installation_Guide_System_Controller_Elan_EL-SC-300.pdf"
 	}
 }

package/config/devices/0x014f/f-adt-hub.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "In the SmartThings mobile app, go to the \"My Home\" section, \"Things\" tab, and tap \"Add a Thing.\" When the app shows \"Looking for devices...\" the panel is ready to include Z-Wave devices",
-		"exclusion": "In the SmartThings mobile app, go to the \"My Home\" section, \"Things\" tab, and tap the name of the device to show the device details. Then, tap the gear icon in the upper right and tap \"Remove.\"\n\nAlternatively, open the side menu (\"More\" in the iOS app) and tap on \"Hub is Online.\" Tap \"Z-Wave Utilities\" then \"General Device Exclusion\" and then the \"Remove\" button to confirm. The panel will enter Exclude Mode.",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "In the SmartThings mobile app, go to the \"My Home\" section, \"Things\" tab, and tap \"Add a Thing.\"",
+		"exclusion": "In the SmartThings mobile app, go to the \"My Home\" section, \"Things\" tab, and tap the name of the device to show the device details. Then, tap the gear icon in the upper right and tap \"Remove.\"",
+		"reset": "Open the side menu and tap on \"Hub is Online.\" Tap \"Z-Wave Utilities\" then \"General Device Exclusion\" and then the \"Remove\" button to confirm.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2616/SmartThings.pdf"
 	}
 }

package/config/devices/0x014f/gd00z-6-7-8.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Place your Z-Wave Controller into Discovery or Include mode.\n\n2. Press and release the link button\non the GD00Z-8.-GC\n\n3. Confirm that the GD00Z-8-GC was recognized by your Z-Wave Controller",
-		"exclusion": "1. Place your Z-Wave Controller into Exclude mode.\n\n2. Press and release the link button\non the GD00Z-8.-GC\n\n3. Confirm that the GD00Z-8-GC was excluded by your Z-Wave Controller",
-		"reset": "Reset the GD00Z-8-ADT by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.\nReset should only be used in the case of a missing or inoperative primary controller",
+		"inclusion": "Press and release the link button.",
+		"exclusion": "Press and release the link button.",
+		"reset": "Press the link button 5 times. A quick beep followed by a longer beep will indicate success.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3710/10025383%20Rev-B%20-%20GD00Z-8%20GC_WEB.pdf"
 	}
 }

package/config/devices/0x014f/husbz.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Not applicable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1363/SmartStick-QuickStart-Guide.pdf"
 	}
 }

package/config/devices/0x014f/lb60z-1.json

@@ -35,8 +35,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the controller in inclusion mode, turn the power to the light bulb socket ON.",
-		"exclusion": "Reset the bulb by using the wall switch to turn the power to the bulb ON while the controller is in exclusion mode. The Smart LED Light Bulb will flash twice to confirm the removal.",
+		"inclusion": "Turn the power to the light bulb socket ON.",
+		"exclusion": "Use the wall switch to turn the power to the bulb ON. The Smart LED Light Bulb will flash twice to confirm removal.",
 		"manual": "https://www.gocontrol.com/manuals/LB60Z-1-Install.pdf"
 	}
 }

package/config/devices/0x014f/ps15emz51.json

@@ -37,8 +37,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the controller in inclusion mode, tap the button on the face of the outlet. The LED will blink slowly when adding.",
-		"exclusion": "Remove the switch by tapping the button on the face of the outlet 2 times. The LED will begin blinking slowly for 10 seconds indicating that it has been removed.",
+		"inclusion": "Tap the button on the face of the outlet. The LED will blink slowly during addition.",
+		"exclusion": "Tap the button on the face of the outlet 2 times. The LED will begin blinking slowly for 10 seconds during removal.",
 		"manual": "https://www.gocontrol.com/manuals/ps15emz5-1_installation_guide_10008371c.pdf"
 	}
 }

package/config/devices/0x014f/wadwaz-1.json

@@ -24,8 +24,8 @@
 		"mapBasicSet": "auto"
 	},
 	"metadata": {
-		"inclusion": "With your Controller in Inclusion mode, depress the internal program switch for 1 second then release.",
-		"exclusion": "With your Controller in Exclusion mode, depress the internal program switch for 1 second then release.",
+		"inclusion": "Depress the internal program switch for 1 second then release.",
+		"exclusion": "Depress the internal program switch for 1 second then release.",
 		"manual": "https://www.gocontrol.com/manuals/WADWAZ-1-Install.pdf"
 	}
 }

package/config/devices/0x014f/wf00z.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZF5201 to the controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
-		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the program switch for at least 1 second. The LED will go solid when successful.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "Trigger the water sensor 10 times within 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1590/10008416X4%20WF00Z-1%20Instructions.pdf"
 	}
 }

package/config/devices/0x014f/wo15emz5.json

@@ -32,9 +32,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the controller in to INCLUDE mode. Press the button on the unit once.",
-		"exclusion": "Put the controller in to EXCLUDE mode. Press the button on the unit twice.",
-		"reset": "Press the button on the unit five times then press and hold the button for 15 seconds.",
+		"inclusion": "Press the button once.",
+		"exclusion": "Press the button twice.",
+		"reset": "Press the button five times then press and hold the button for 15 seconds.",
 		"manual": "https://www.gocontrol.com/manuals/10010070ax2_wo15emz5-1_instructions.pdf"
 	}
 }

package/config/devices/0x014f/wo15z.json

@@ -23,8 +23,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "Put the controller in to INCLUDE mode. Press the button on the unit once.",
-		"exclusion": "Put the controller in to EXCLUDE mode. Press the button on the unit twice.",
+		"inclusion": "Press the button once.",
+		"exclusion": "Press the button twice.",
 		"manual": "https://www.gocontrol.com/manuals/WO15Z-1-Install.pdf"
 	}
 }

package/config/devices/0x014f/ws15z-1.json

@@ -28,8 +28,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the controller in inclusion mode, press the top of the switch two times.",
-		"exclusion": "With the controller in exclusion mode, press the top of the switch two times.",
+		"inclusion": "Press the top of the switch twice.",
+		"exclusion": "Press the top of the switch twice.",
 		"manual": "https://www.nortekcontrol.com/wp-content/uploads/WS15Z1_manual.pdf"
 	}
 }

package/config/devices/0x0157/ebv-105.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2.Once the controller is ready to include your device, press the red button 3 times to include it in the Z-Wave network",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device to the Z-Wave network.\n2.Once the controller is ready to exclude your device, press the red button 3 times to exclude it from the Z-Wave network",
-		"reset": "Press and hold the button 10 seconds and release the button. The device will send the reset notification to the list node in the group1 and erases the device memory , when the light flash it is resetting success.\nNote: This should only be used in the event your networks primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the red button 3 times.",
+		"exclusion": "Press the red button 3 times.",
+		"reset": "Press and hold the button for 10 seconds and release (the light will flash when reset is successful).",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1560/EBV105-Z-Valve-Quick-Start-Guide-M2-ZWP.pdf"
 	}
 }

package/config/devices/0x015a/jtb-3005-03.json

@@ -44,9 +44,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Start master controller add device mode as instruction, press 3 time of PB button located on the back side of thermostat panel in 1.5 second,\nLED flash indicator inclusion processing until included or 60 second timeout no detect any master controller",
-		"exclusion": "Start master controller remove device mode as instruction, press 3 time of PB button located on the back side of thermostat panel in 1.5 second, LED flash indicator exclusion processing until excluded or 5 second timeout no detect any master controller",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nPress and hold PB button located on the back side of thermostat\npanel for 10 seconds retrieve thermostat panel factory default",
+		"inclusion": "Press the PB button on the back side 3 times within 1.5 seconds. The LED will flash during inclusion.",
+		"exclusion": "Press the PB button on the back side 3 times within 1.5 seconds. The LED will flash during exclusion.",
+		"reset": "Press and hold the PB button on the back side for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2634/JTB-3005-03-Manual_20171016.pdf"
 	}
 }

package/config/devices/0x015a/jtb-3011-03.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Start master controller add device mode as instruction, press and hold the channel 1 touch icon (located on leftmost) for 2 second, RF icon LED on right bottom flash\nindicator inclusion processing until included or 60 seconds timeout no detect any master controller",
-		"exclusion": "Start master controller remove device mode as instruction, press and hold the channel 1 touch icon (located on leftmost) for 2 second, RF icon LED on right bottom flash indicator inclusion processing until included or 15 seconds timeout no detect any master controller.\nLED flash slowly indicated has no included any controller",
-		"reset": "The factory default settings are restored when the device is removed from the network.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and hold the leftmost touch icon (channel 1) for 2 seconds. The RF LED on the right bottom will flash during inclusion.",
+		"exclusion": "Press and hold the leftmost touch icon (channel 1) for 2 seconds. The RF LED on the right bottom will flash during exclusion.",
+		"reset": "Remove the device from the network to restore factory default settings.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2591/JTB-3011-03-Manual_20171030_Ver_1_1.pdf"
 	}
 }

package/config/devices/0x015b/ihu50.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Select ‘setDefault' in [Command List]\n Click Send(Default) button.",
+		"reset": "1. Select 'setDefault' in [Command List]\n2. Click Send(Default) button",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1457/APP%20Manual.pdf"
 	}
 }

package/config/devices/0x015b/lap255u.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Run Z-Wave Certification Application in Setting, Select \"Things\" on the left menu, select \"bridge\" on the right list, and Select factoryReset on the right list, push Send button on the Pop up",
+		"reset": "1. Run Z-Wave Certification Application in Setting\n2. Select \"Things\" on the left menu\n3. Select \"bridge\" on the right list\n4. Select factoryReset on the right list\n5. Push Send button on the Pop up",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1453/ZwaveCertiApp_Guide_0902_new.pdf"
 	}
 }

package/config/devices/0x015d/nzw1201.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "First put your Z-Wave enabled HUB in inclusion mode. Next, insert the battery and it will automatically connect to your HUB. If it does not automatically connect after 30 seconds, press the manual button three (3) times",
-		"exclusion": "Put your HUB in exclusion mode and press the manual button three (3) times",
-		"reset": "Please use a certified controller to remove the device from your network to factory default. Or, to manually remove your device, hold down the button for 5 seconds. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the manual button 3 times.",
+		"exclusion": "Press the manual button 3 times.",
+		"reset": "Hold down the button for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2658/NZW1201%20-%20Manual%20v1%20Compressed.pdf"
 	}
 }

package/config/devices/0x015d/nzw31t.json

@@ -14,9 +14,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Primary inclusion method is via, \"Auto-Inclusion\". Start the inclusion process on your HUB/Gateway and then flip the circuit back on to bring power to your device. You will have 30 seconds before the device times out. The backup method is toggling UP on the switch 6 times within 2 seconds.",
-		"exclusion": "Toggle UP on the switch 6 times within 2 seconds",
-		"reset": "Please use your controller to remove the device from the network. To factory reset, toggle UP the switch 10x in a row when powered on. However, please only use this method if your controller is missing or inoperable.",
+		"inclusion": "Toggle UP on the switch 6 times within 2 seconds.",
+		"exclusion": "Toggle UP on the switch 6 times within 2 seconds.",
+		"reset": "Toggle UP the switch 10 times in a row when powered on.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2679/NZW31Tmanual171102.pdf"
 	}
 }

package/config/devices/0x015d/zen20.json

@@ -251,9 +251,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to \n the Z-Wave network.\n2. Once the controller is ready to include your device, press up and release the toggle \n to include it in the network.\n3. Once your controller has confirmed that the device has been included, refresh the \n Z-Wave network to optimize performance.\n4. The device is associated in the same group when it included in setting process. \n Now you can control your Z-Wave device according to groups, scenes, schedules and automation programmed",
-		"exclusion": "1. Plug the power strip into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n\n2. Put your Z-Wave controller in exclusion mode\n\n3. Press and release the power button on the strip\n\n4. The device should disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the power strip into a grounded receptacle, then PRESS AND HOLD the power button for AT LEAST 3 SECONDS. NOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "Press up and release the toggle.",
+		"exclusion": "Press and release the power button on the strip.",
+		"reset": "Press and hold the power button for at least 3 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1818/Zooz-Z-Wave-Power-Strip-Zen20-Manual.pdf"
 	}
 }

package/config/devices/0x015d/zen21.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Bring your Z-Wave gateway hub or controller as close to the switch as possible\n2. Put your Z-Wave controller in inclusion mode\n3. Tap the switch on and off quickly 3 times to finalize the inclusion process\n4. A new on/off device should appear on your controller's device list\n\nTroubleshooting Tips:\nIf you are unable to include the Z-Wave switch to your controller, please try one of the following:\n- Bring the controller closer to your Z-Wave switch or use a hand-held secondary controller for inclusion\n- Tap your Z-Wave switch quicker 4 or 5 times once you put the controller in the inclusion mode to ensure the command has gone through\n- Put your controller in the EXCLUSION mode and tap the switch quickly 3 times, then try adding it to your network again",
-		"exclusion": "1. Bring your Z-Wave gateway hub or controller as close to the switch as possible\n2. Put your Z-Wave controller in exclusion mode\n3. Tap the switch on and off quickly 3 times to complete the exclusion process\n4. The device should disappear from your controller's device list\n\nPlease repeat the process following all steps carefully if the first attempt is unsuccessful",
-		"reset": "The switch will be reset to factory defaults only by exclusion using a Z-Wave controller. You may use any certified Z-Wave controller to exclude and reset the switch. This device may not be reset manually when the network's primary controller is missing or otherwise inoperable. NOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "Tap the switch on and off quickly 3 times.",
+		"exclusion": "Tap the switch on and off quickly 3 times.",
+		"reset": "Exclude the device from the network to reset it to factory defaults.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1945/zooz-z-wave-plus-on-off-switch-zen21-manual.pdf"
 	}
 }

package/config/devices/0x015d/zw-1104.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to \n the Z-Wave network.\n2. Once the controller is ready to include your device, press up and release the toggle \n to include it in the network.\n3. Once your controller has confirmed that the device has been included, refresh the \n Z-Wave network to optimize performance.\n4. The device is associated in the same group when it included in setting process. \n Now you can control your Z-Wave device according to groups, scenes, schedules \n and automation programmed.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device \n from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, press up and release the toggle \n to exclude it from the network.",
-		"reset": "1. Press and hold the top button for at least 3 seconds while you insert the batteries.\n2. Use this procedure only in the event that the network primary controller is missing \n or otherwise inoperable.",
+		"inclusion": "Press up and release the toggle.",
+		"exclusion": "Press up and release the toggle.",
+		"reset": "Press and hold the top button for at least 3 seconds while inserting the batteries.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1645/ZW1104-Manual0130.pdf"
 	}
 }

package/config/devices/0x015d/zw1101.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, triple click the micro switch to include it in the network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, triple click the micro switch to exclude it from the network.",
-		"reset": "Press and hold the micro switch for at least 3 seconds while you insert the battery to reset the device.\n*Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple click the micro switch.",
+		"exclusion": "Triple click the micro switch.",
+		"reset": "Press and hold the micro switch for at least 3 seconds while inserting the battery.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2010/ZW1101-Manual0929.pdf"
 	}
 }

package/config/devices/0x015d/zw1103.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, triple click the ADD Button to include it in the network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, triple click the ADD Button to exclude it from the network.",
-		"reset": "Press and hold ADD Button for at least 3 seconds while you insert the battery.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple click the ADD button.",
+		"exclusion": "Triple click the ADD button.",
+		"reset": "Press and hold the ADD button for at least 3 seconds while inserting the battery.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2016/ZW1103-Manual0929.pdf"
 	}
 }

package/config/devices/0x015d/zw1105.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, triple click the Tamper switch to include it in the network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, triple click the Tamper switch to exclude it from the network.",
-		"reset": "Press and hold Tamper switch for at least 3 seconds while you insert the batteries.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple click the Tamper switch.",
+		"exclusion": "Triple click the Tamper switch.",
+		"reset": "Press and hold the Tamper switch for at least 3 seconds while inserting the batteries.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2014/ZW1105-Manual0929.pdf"
 	}
 }

package/config/devices/0x015d/zw112.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, triple click Tamper switch to include it in the network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, triple click Tamper switch to exclude it from the network.",
-		"reset": "Press and hold Tamper switch for at least 3 seconds while you insert the battery. \n*Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple click the Tamper switch.",
+		"exclusion": "Triple click the Tamper switch.",
+		"reset": "Press and hold the Tamper switch for at least 3 seconds while inserting the battery.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2009/ZW112-Manual0930.pdf"
 	}
 }