@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x0108/dch-z120.json

@@ -212,9 +212,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo add into a Z-Wave network: \n1. Have Z-Wave Controller entered inclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds",
-		"exclusion": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo remove the device from a Z-Wave network: \n1. Have Z-Wave Controller entered exclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.\nNode ID has been excluded",
-		"reset": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo reset the device: \nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are excluded and all settings will reset to factory default",
+		"inclusion": "Press the tamper key three times within 1.5 seconds.",
+		"exclusion": "Press the tamper key three times within 1.5 seconds.",
+		"reset": "1. Press the tamper key four times within 1.5 seconds and hold on the fourth press until the LED lights up.\n2. After 3 seconds the LED will turn off.\n3. Release the tamper key within 2 seconds. The LED will light for 1 second if successful or flash once if unsuccessful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1152/D-Link%20DCH-Z110_120%20manual.pdf"
 	}
 }

package/config/devices/0x0108/dch-z310.json

@@ -45,9 +45,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing button three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing button three times within 1.5 seconds to enter the exclusion mode. Node ID has been removed",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Pressing button four times within 1.5 seconds and do not release the button in the 4 th pressed, and the red LED will light ON.\n2. After the red LED flash 9 times, release the button within 2 seconds.\n3. IDs are removed and all settings will reset to factory default",
+		"inclusion": "Press the button three times within 1.5 seconds.",
+		"exclusion": "Press the button three times within 1.5 seconds.",
+		"reset": "1. Press the button four times within 1.5 seconds and hold on the fourth press until the red LED lights up.\n2. After the red LED flashes 9 times, release the button within 2 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1261/DCH-Z310_Manual.pdf"
 	}
 }

package/config/devices/0x0108/dch-z510.json

@@ -49,9 +49,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing tamper key three times within 1.5 seconds\nto enter the inclusion mode.\n3. After add successful, the LED will light ON 1 second",
-		"exclusion": "1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.\nNode ID has been excluded",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4 pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are excluded and all settings will reset to factory default",
+		"inclusion": "Press the tamper key three times within 1.5 seconds. The LED will light for 1 second.",
+		"exclusion": "Press the tamper key three times within 1.5 seconds.",
+		"reset": "1. Press the tamper key four times within 1.5 seconds and hold on the fourth press until the LED lights up.\n2. After 3 seconds the LED will turn off.\n3. Release the tamper key within 2 seconds. The LED will light for 1 second if successful or flash once if unsuccessful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1262/DCH-Z510_Manual.pdf"
 	}
 }

package/config/devices/0x0109/azl7434.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL 7434-5 to your controller. To get in the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL 7434-5 from your controller. \nPress 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
-		"reset": "Power off first, press Program Switch and power on, ZL7434-5 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds.",
+		"exclusion": "Press the program switch 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds.",
+		"reset": "Power off the device, press the program switch, then power on.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1378/Microsoft%20Word%20-%20ZL7434-5%20In-Wall%20Switch%20-%201%20Relay_20150520.pdf"
 	}
 }

package/config/devices/0x0109/za1011eu-5.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1) Select 'Reset Locally' button.\n2) Confirm the dialog. This will perform a factory reset to the Gateway.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Select the 'Reset Locally' button.\n2. Confirm the dialog.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3417/ZA1011EU-5_UserManual.pdf"
 	}
 }

package/config/devices/0x0109/zb5311us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZB5311-5 to your controller. To get in the 'inclusion' mode, press the Program Switch of ZB5311-5 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZB5311-5 will go to sleep after 30 seconds. After inclusion successfully, the Green LED will be solid on for 0.5 second",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZB5311-5 from your controller. Press the Program Switch of ZB5311-5 once to be excluded, the Green LED will flash 5 times quickly after successful exclusion.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: Long press the program switch up to 10 seconds to send the 'Device Reset Locally Notification' command and reset to the factory default. The Green LED will flash 5 times quickly after finishing the Factory Default Reset.\n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch once. The green LED will be solid on for 0.5 second after successful inclusion.",
+		"exclusion": "Press the program switch once. The green LED will flash 5 times quickly after successful exclusion.",
+		"reset": "Long press the program switch for up to 10 seconds. The green LED will flash 5 times quickly after successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3819/ZB5311-5%20Glass%20Break%20Detector%20Manual%20(RD%20%20FCC%20Checked)_20200304.pdf"
 	}
 }

package/config/devices/0x0109/zd2105.json

@@ -20,9 +20,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2105 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2105 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2105 will go to sleep after 20 seconds",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2105 from your controller. Press the Program Switch of ZD2105 for 1 second at least to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2105 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Trigger the rear cover switch.\n2. Trigger the reed switch (close & open) 5 times in 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2850/ZD%202105-5_20180126%20(SDK6.81).pdf"
 	}
 }

package/config/devices/0x0109/zd2106us-7.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2106 to your controller. To get in the 'inclusion' mode, make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2106 will go to sleep after 30 seconds",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2106 from your controller. Make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: \nOpen the rear cover to trigger the rear cover switch for sending the Alarm Report and trigger the reed switch (close & open) 10 times in 10 seconds, ZD2106 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Ensure the rear cover is closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds.",
+		"exclusion": "Ensure the rear cover is closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds.",
+		"reset": "1. Open the rear cover to trigger the rear cover switch.\n2. Trigger the reed switch (close & open) 10 times in 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3878/ZD2106-7%20Door%20Sensor%20(20200506).pdf"
 	}
 }

package/config/devices/0x0109/zd2112jp-5.json

@@ -36,9 +36,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2112 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2112 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2112 will go to sleep after 20 seconds.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2112 from your controller. Press the program switch of ZD2112 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2112 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Trigger the rear cover switch.\n2. Trigger the reed switch (close & open) 5 times in 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1750/ZD%202112-5_12122014-Japan%20DW.pdf"
 	}
 }

package/config/devices/0x0109/zd2201.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2301 to your controller, to get in the 'inclusion' mode. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
-		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the 'Device Reset Locally' command and reset to the factory default. \n* Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the program switch.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Open the rear cover.\n2. Press the program switch 10 times in 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2480/ZD%202201-5_R1_20150812.pdf"
 	}
 }

package/config/devices/0x0109/zd2301eu-5.json

@@ -68,9 +68,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "4. For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2301 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "5. For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the 'Device Reset Locally' command and reset to the factory default. \n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the program switch.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Open the rear cover.\n2. Press the program switch 10 times in 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1334/ZD%202301-5_20150603.pdf"
 	}
 }

package/config/devices/0x0109/zf5201eu-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZF5201 to the controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
-		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go solid if successful.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "Trigger the water sensor 10 times within 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1718/ZF%205201-5_20141118.pdf"
 	}
 }

package/config/devices/0x0109/zg8101.json

@@ -31,8 +31,8 @@
 		"forceNotificationIdleReset": true
 	},
 	"metadata": {
-		"wakeup": "Remove the cover of ZG8101",
-		"inclusion": "1. Initiate inclusion on your Z Wave controller. The distance between sensor and controller is suggested to be less than 1 meter.\n2. Press the program switch of the ZG8101 for at least 1 second.\n3. The LED on the ZG8101 should go solid, if not, please try again.",
-		"exclusion": "1. Initiate exclusion on your Z Wave controller.\n2. Press the program switch of ZG8101 for 1 second at least to be excluded."
+		"wakeup": "Remove the cover.",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go solid if successful.",
+		"exclusion": "Press the program switch for at least 1 second."
 	}
 }

package/config/devices/0x0109/zl7201de-5.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL7201 into your controller. To get in the 'Inclusion' mode, the distance between ZL7201 and controller is suggested to be in one meter. By power up to get included for first time, or press the Program switch (The LED at the top of plug-in) 3 times within 2 seconds to be included",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL7201 from your controller. Press the Program Switch (The LED at the top of plug-in) 3 times within 2 seconds to be excluded",
-		"reset": "Reset: Press the Program Switch (The LED at the top of plug-in) then power on (plug-in) and hold for 5 seconds before release the switch.\n\nNoticed: only use Reset for the situation where the primary controller is inoperable or lost",
+		"inclusion": "Press the program switch 3 times within 2 seconds.",
+		"exclusion": "Press the program switch 3 times within 2 seconds.",
+		"reset": "Press the program switch, then power on and hold for 5 seconds before releasing the switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1083/ZL%207261-5_%20Power%20Monitor_20140814.pdf"
 	}
 }

package/config/devices/0x0109/zl7435-5.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL 7435EU-5 to your controller. To get in the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. \nPress 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL 7435EU-5 from your controller. Press 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
-		"reset": "Factory Default Reset: Power off first, press Program Switch and power on till 10 seconds, ZL7435EU-5 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds.",
+		"exclusion": "Press 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds.",
+		"reset": "1. Power off first.\n2. Press program switch and power on for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1367/ZL7435-5%20In-Wall%20Switch%20-%202%20Relays_20141205.pdf"
 	}
 }

package/config/devices/0x0109/zm1601-5.json

@@ -47,9 +47,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' (adding to) a network, put the Z-Wave™ network controller into 'inclusion' mode, and following its instruction to add the ZM 1601 to your controller. To get the ZM 1601 in the 'inclusion' mode, open the bracket and press the program switch of ZM 1601 for 1 second at least & release to be included. After waiting a few seconds the LED Setting Lighting should go off, if not, please try again. (After sending the Z-Wave NIF one time if the ZM1601 is not included it will send 4 times Network Wide Inclusion request every 4 ~ 6 seconds for auto inclusion. The orange LED will flash again if the siren has not been included or the orange LED will go off after inclusion.)",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ network controller into 'exclusion' mode, and following its instruction to delete the ZM 1601 from your controller. Press the program switch of ZM 1601 for 1 second at least & release to be excluded. Note: a. LED setting light will flash (orange color) continuously in Exclusion condition for 25 seconds. b. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
-		"reset": "All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
+		"inclusion": "Open the bracket and press the program switch for at least 1 second. The LED should go off after successful inclusion or flash orange continuously if not included.",
+		"exclusion": "Press the program switch for at least 1 second. LED will flash orange continuously for 25 seconds during exclusion.",
+		"reset": "Device resets to factory defaults when excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1009/ZM%201601%20Siren_20140407-500%20series.pdf"
 	}
 }

package/config/devices/0x0109/zm1602-5.json

@@ -83,9 +83,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1602 to your controller. To get in the 'inclusion' mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
-		"exclusion": "Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
-		"reset": "This device can't be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Open the bracket and press the program switch for at least 1 second. The LED should go off after successful inclusion.",
+		"exclusion": "Press the tamper switch for at least 1 second.",
+		"reset": "Device resets to factory defaults when excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1276/ZM%201602-5%20Siren_R3_20170301.pdf"
 	}
 }

package/config/devices/0x0109/zm1602.json

@@ -77,9 +77,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1602 to your controller. To get in the 'inclusion' mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
-		"exclusion": "Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
-		"reset": "This device can't be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Open the bracket and press the program switch for at least 1 second. The LED should go off after successful inclusion.",
+		"exclusion": "Press the tamper switch for at least 1 second.",
+		"reset": "Device resets to factory defaults when excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1276/ZM%201602-5%20Siren_R3_20170301.pdf"
 	}
 }

package/config/devices/0x0109/zm1611jp-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM1611-5 to your controller. To get in the 'inclusion' mode, press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be included. After setting, the LED should go off, if not, please try again. (After sending one time's Z-Wave NIF and not be included then it will send 4 times NWI in every 30 seconds for auto inclusion. The LED will flash again if the U-Bell has not been included or the LED will go off after inclusion.)",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZM1611-5 from your controller. Press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be excluded. The LED will flash again after exclusion",
-		"reset": "For \"Reset\": Press and hold the Program Switch for 5 seconds 'at least', power on until the LED turns on then release the switch, U-Bell will send Command Class Device Reset Locally for Reset Process. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press and hold the program switch for at least 3 seconds. The LED should go off after successful inclusion or flash if not included.",
+		"exclusion": "Press and hold the program switch for at least 3 seconds. The LED will flash after exclusion.",
+		"reset": "Press and hold the program switch for at least 5 seconds, power on until the LED turns on, then release the switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3572/ZM1611-5%20USER%20MANUAL.pdf"
 	}
 }

package/config/devices/0x0109/zm1621.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1621 to your controller. To get in the 'inclusion' mode, get magnet of the bracket to touch the reed switch on the ZM1621 and separate at once to be included. After setting, the LED Light should go off, if not, please try again. (After sending one time's Z-Wave NIF and not be included then it will send NWI for auto inclusion. The LED light will flash again if the siren has not been included or the LED light will go off after inclusion.)",
-		"exclusion": "For 'Exclusion' in (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZM 1621 from your controller. ZM1621-5 will send NWE if the exclusion could not be done successfully. \nNote:\na. LED light will flash continuously in Exclusion condition.\nb. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "ZM 1621 will reset to factory default when the device has been excluded.\n(Please use this procedure only in the event that your network primary controllers is missing or otherwise inoperable!)",
+		"inclusion": "Touch the magnet of the bracket to the reed switch and separate immediately. The LED should go off after successful inclusion or flash if not included.",
+		"exclusion": "Touch the magnet of the bracket to the reed switch and separate immediately. LED will flash continuously during exclusion.",
+		"reset": "Device resets to factory defaults when excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2992/ZM1621-5%20Outdoor%20Siren%20(SDK6.51.10).pdf"
 	}
 }

package/config/devices/0x0109/zp3111-5.json

@@ -131,10 +131,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the ZP3111 to the Z-Wave network (inclusion), place the Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds.",
-		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
-		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
-		"wakeup": "Press the Programm Switch once.",
+		"inclusion": "Press the program switch once.",
+		"exclusion": "Press the program switch once.",
+		"reset": "1. Remove cover to trigger tamper switch.\n2. Press program switch 10 times within 10 seconds.",
+		"wakeup": "Press the program switch once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2479/ZP3111-5_R2_20170316.pdf"
 	}
 }

package/config/devices/0x0109/zp3113-7.json

@@ -118,9 +118,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: To add the ZP3113 to your Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3113 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3113 will go to sleep after 30 seconds. The LED indicator will be flashing while the inclusion is continued",
-		"exclusion": "For 'Exclusion' from (removing from) a network: To remove the ZP3113 from your Z-Wave network (exclusion), place your Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3113 to your controller. Press the Program Switch of ZP3113 once to be excluded.",
-		"reset": "Factory Default Reset: \nRemove cover to triggered tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3113 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch once. The LED indicator will flash during inclusion.",
+		"exclusion": "Press the program switch once.",
+		"reset": "1. Remove cover to trigger tamper switch.\n2. Press program switch 10 times within 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4314/ZP3113-7%204%20in%201%20PIR%20(Z-Wave%20certified)%20-%2020211004.pdf"
 	}
 }

package/config/devices/0x0109/zr1202.json

@@ -25,9 +25,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode and following its instruction to add the ZR1202 to your controller. To get into the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the ZR1202 three times in 3 seconds. The LED should stop flashing, if not, please try again.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZR1202 from your controller. Press the program switch on the ZR1202 three times in 3 seconds to be excluded.\nNote: LED setting light will flash continuously in Exclusion condition.",
-		"reset": "Press Program Switch for 5 seconds, the ZR1202 will reset back to factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch three times within 3 seconds. The LED should stop flashing if successful.",
+		"exclusion": "Press the program switch three times within 3 seconds. The LED will flash continuously if successful.",
+		"reset": "Press the program switch for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1325/ZR1202-5%20Repeater.pdf"
 	}
 }

package/config/devices/0x0109/zs5101us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS 5101-5 to your controller. To get in the 'inclusion' mode, please press the program switch of ZS 5101-5 for 1 second at least to be included. The LED on the ZS 5101-5 should go off, if not, please try again",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS 5101-5 from your controller. Press the program switch of ZS 5101-5 for 1 second at least to be excluded.",
-		"reset": "*Push the Tamper switch then power on (put in the battery) & hold the Tamper switch for 5 seconds, ZD5101-5 will send the 'Device Reset Locally Notification' command and reset to the factory default, LED will solid on, need to take off the battery and re-put in the battery to complete the function.\n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Push the tamper switch\n2. Insert the battery while holding the tamper switch\n3. Hold the tamper switch for 5 seconds\n4. Remove and reinsert the battery to complete the reset\n\nThe LED will turn solid on during the reset process.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2099/ZS%205101-5_V1_20160427.pdf"
 	}
 }

package/config/devices/0x0109/zs6101.json

@@ -26,8 +26,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6101-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6101-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6101-5 from your controller. Press the program switch of ZS6101-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second. The red LED will flash continuously if successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1085/ZS%206101-5_ZS6102-5%20%20Smoke%20Detector.pdf"
 	}
 }

package/config/devices/0x0109/zs6102eu-5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6102-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6102-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6102-5 from your controller. Press the program switch of ZS6102-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
-		"reset": "ZS6102-5 will reset back to the factory default value after being excluded from the network.",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second. The red LED will flash continuously if successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1084/ZS%206101-5_ZS6102-5%20%20Smoke.pdf"
 	}
 }

package/config/devices/0x0109/zs6301-5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6301-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. By power on to get included for first time or press the test switch of ZS6301-5 once to be included. After be included, the red LED will go on",
-		"exclusion": "For 'Exclusion' from (removing from) a net work: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6301-5 from your controller. Press the test switch of ZS6301-5 once to be excluded.",
-		"reset": "N/A",
+		"inclusion": "Press the test switch once. The red LED will turn on if successful.",
+		"exclusion": "Press the test switch once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1328/ZS6301-5%20CO%20Detector.pdf"
 	}
 }

package/config/devices/0x0109/zt1101.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send 'Device Reset Locally Notification' command and reset to the factory default. (Red LED flashes fast means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
+		"reset": "Press all 4 buttons together for 10 seconds. The LED will turn red for 2 seconds, then green for 2 seconds. A fast flashing red LED indicates reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1706/ZT1101-5%20Keyfob_R1_20150703.pdf"
 	}
 }

package/config/devices/0x0109/zt1141eu-5.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red then turn green. (Green LED flashes 5 times quickly that means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
+		"reset": "Press all 4 buttons together for 10 seconds. The LED will turn red then green. A green LED flashing 5 times quickly indicates reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1709/ZT1141-5%20Wall%20Remote.pdf"
 	}
 }

package/config/devices/0x0109/zw4111eu-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "3. For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode, and following its instruction to add the ZW4111 to your controller. To get in the 'inclusion' mode, press the program switch 3 times or outer switch 1 / switch 2 to be included. \nNOTE: The red LED will flash if ZW4111 has not been included before or the red LED will be OFF.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZW 4101 / ZW4111 from your controller. Press the program switch or outer switch 1 / switch 2 3 times to be excluded",
-		"reset": "Press Program Switch and power on till 5 seconds, ZW4111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch 3 times or press switch 1 or switch 2. The red LED will be off if successful.",
+		"exclusion": "Press the program switch 3 times or press switch 1 or switch 2 three times.",
+		"reset": "Press the program switch and power on, holding for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1582/ZW%204111-5%20Curtain%20(Screw%20Terminal)%2020151124.pdf"
 	}
 }

package/config/devices/0x010a/vitrum_i_dimmer.json

@@ -27,8 +27,8 @@
 	},
 	"metadata": {
 		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
-		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_i_switch.json

@@ -26,8 +26,8 @@
 	},
 	"metadata": {
 		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
-		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_ii_dimmer.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_ii_switch.json

@@ -29,9 +29,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_iii_eu_dimmer.json

@@ -28,9 +28,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_i.json

@@ -20,9 +20,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_iv.json

@@ -32,9 +32,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }