@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x0086/zw099.json

@@ -183,9 +183,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product housing",
+		"exclusion": "Short press the Action button on the product housing",
+		"reset": "Press and hold the Action button on the product housing for 20 seconds and then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2246/Aeon%20Labs%20Smart%20Dimmer%206%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw100.json

@@ -572,9 +572,9 @@
 		"reportTimeout": 2000
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Z-Wave button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Z-Wave button that you can find in back of the product",
-		"reset": "Press and hold the Z-Wave button that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Z-Wave button on the back of the product",
+		"exclusion": "Short press the Z-Wave button on the back of the product",
+		"reset": "Press and hold the Z-Wave button on the back of the product for 20 seconds and then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1390/Aeon%20Labs%20MultiSensor%206%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw111.json

@@ -492,9 +492,9 @@
 		"treatMultilevelSwitchSetAsEvent": true
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product housing",
+		"exclusion": "Short press the Action button on the product housing",
+		"reset": "Press and hold the Action button on the product housing for 20 seconds and then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2149/Aeon%20Labs%20Nano%20Dimmer%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw112.json

@@ -87,9 +87,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action Button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action Button that you can find in back of the product",
-		"reset": "Press the Action Button once that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action Button on the back of the product",
+		"exclusion": "Short press the Action Button on the back of the product",
+		"reset": "Press the Action Button on the back of the product for 20 seconds and then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1611/Door%20Window%20Sensor%206%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw116.json

@@ -440,9 +440,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product housing",
+		"exclusion": "Short press the Action button on the product housing",
+		"reset": "Press and hold the Action button on the product housing for 20 seconds and then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2208/Nano%20Switch%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw117.json

@@ -74,9 +74,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, press the Z-Wave Button on Range Extender 6",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, press the Z-Wave Button on Range Extender 6",
-		"reset": "Press and hold the Z-Wave Button for 20 seconds and then release it.\nUse this procedure only in the event that your primary network controller is missing or inoperable",
+		"inclusion": "Press the Z-Wave Button on Range Extender 6",
+		"exclusion": "Press the Z-Wave Button on Range Extender 6",
+		"reset": "Press and hold the Z-Wave Button for 20 seconds and then release it",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2520/Range%20Extender%206%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw120.json

@@ -84,9 +84,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action Button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action Button that you can find in back of the product",
-		"reset": "Press the Action Button once that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action Button on the back of the product.",
+		"exclusion": "Short press the Action Button on the back of the product.",
+		"reset": "Press and hold the Action Button on the back of the product for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1574/Door%20Window%20Sensor%20Gen5%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw121.json

@@ -373,9 +373,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, press the Action Button on the LED Strip Controller",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, press the Action Button on the LED Strip Controller",
-		"reset": "Press and hold the Action Button on the LED Strip Controller for 20 seconds and then release it.\nUse this procedure only in the event that your primary network controller is missing or inoperable",
+		"inclusion": "Press the Action Button on the LED Strip Controller.",
+		"exclusion": "Press the Action Button on the LED Strip Controller.",
+		"reset": "Press and hold the Action Button on the LED Strip Controller for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1963/LED%20Strip%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw122.json

@@ -390,9 +390,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action Button that you can find on the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action Button that you can find on the product",
-		"reset": "Press and hold the Action Button that you can find on the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action Button on the product.",
+		"exclusion": "Short press the Action Button on the product.",
+		"reset": "Press and hold the Action Button on the product for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2407/Aeon%20Labs%20Water%20Sensor%206%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw129.json

@@ -106,7 +106,7 @@
 		}
 	],
 	"metadata": {
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2232/Aeon%20Labs%20WallMote%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw130.json

@@ -132,9 +132,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable",
+		"inclusion": "Short press the Action button on the product's housing.",
+		"exclusion": "Short press the Action button on the product's housing.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3264/Aeon%20Labs%20WallMote%20Quad%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw132.json

@@ -513,9 +513,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product's housing.",
+		"exclusion": "Short press the Action button on the product's housing.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2136/Dual%20Nano%20Switch%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw139.json

@@ -304,9 +304,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product's housing.",
+		"exclusion": "Short press the Action button on the product's housing.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2306/Nano%20Switch%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw140.json

@@ -304,9 +304,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product's housing.",
+		"exclusion": "Short press the Action button on the product's housing.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2247/Dual%20Nano%20Switch%20manual.pdf"
 	}
 }

package/config/devices/0x0086/zw141.json

@@ -110,9 +110,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing.\n\nIf the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid. If unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the instructions above from step 1.",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, quick press the product's Action button 6 times that you can find on the product's housing or toggle the external manual switch 2 times in fast succession.\n\nIf the Nano Dimmer has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load), repeat the instructions above from step 1",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or otherwise inoperable",
+		"inclusion": "Short press the Action button on the product's housing. If successful, the RGB LED will be solid. If unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient.",
+		"exclusion": "Quick press the Action button 6 times on the product's housing or toggle the external manual switch 2 times in fast succession. If successful, the RGB LED will remain colorful gradient. If unsuccessful, the RGB LED will still be solid.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3269/Aeon%20Labs%20Nano%20Shutter%20-manual%20-%202.pdf"
 	}
 }

package/config/devices/0x0090/8225.json

@@ -172,9 +172,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3353/Baldwin_8225_Product_Manual_5_9.pdf"
 	}
 }

package/config/devices/0x0090/8252.json

@@ -172,9 +172,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3070/Install_Guide_8285_9_5_2018.pdf"
 	}
 }

package/config/devices/0x0090/910.json

@@ -235,9 +235,9 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2239/Install_Guide_910_02_27_2017.pdf"
 	}
 }

package/config/devices/0x0090/ged1455.json

@@ -221,9 +221,9 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "http://www.weiserlock.com/PDFs/instructions/Electronics/SmartCode_5_Installation_and_User_Guide_English.pdf"
 	}
 }

package/config/devices/0x0090/ged2350.json

@@ -172,9 +172,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2377/Install%20Guide%20GED2350%2004242017.pdf"
 	}
 }

package/config/devices/0x0090/smartcode_888.json

@@ -184,9 +184,9 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
-		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
+		"inclusion": "Press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.",
+		"exclusion": "Press button A on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"reset": "1. Remove the battery pack.\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2176/Install%20Guide%20888%20ENG_Merged.pdf"
 	}
 }

package/config/devices/0x0094/2gig-edg-n.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Reset Controller\nAvailable only for Installers, the Reset Controller option\nis also found on the Z-Wave settings menu.\nReset the panel's Z-Wave Controller back to default\nsettings.\n1. Tap Reset Controller",
+		"reset": "Tap 'Reset Controller' in the Settings menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4076/10029908%20Rev-X11b%20-%202GIG%20Edge%20User%20Guide_sm.pdf"
 	}
 }

package/config/devices/0x0094/adc-200h-ev.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1.1 Adding devices to the Alarm.com Module's Z-Wave Network\nNOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com Module will have network information replicated over to them.\n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest.\nb. Move all Z-Wave devices to their final location on the property.\nc. Navigate to the Equipment List page.\nd. Select emPower Management.\ne. Select Add Z-Wave Devices\nf. Wait for the bolded message: Checking for new devices on the network\ng. Trigger a device to add it to the network.\nh. When a device is added successfully, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page.\nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List.\nd. Click Add Z-Wave Devices.\ne. Wait for the bolded message: Checking for new devices on the network.\nf. Trigger a device to add it to the network.\ng. When a device is added successfully, it will show up on this screen following a 30 second delay.\nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n3. Using the Simon XTi Panel\na. Enter System Programming.\nb. Select Interactive Services.\nc. Select Z-Wave.\nd. Select Add Device.\ne. Trigger a device to add it to the network.\nf. When a device is added successfully, the panel will beep.\ng. You will need to re-enter Add Mode before triggering the next device",
-		"exclusion": "List page.\nd. Select emPower Management.\ne. Select Delete Z-Wave Devices\nf. Wait for the bolded message: Checking for deleted devices on the network\ng. Trigger a device to remove it from the network.\nh. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to delete close to the Alarm.com Module.\nb. Navigate to the Equipment page.\nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List.\ne. Click Delete Z-Wave Devices.\nf. Wait for the bolded message: Checking for deleted devices on the network.\ng. Trigger a device to remove it from the network.\nh. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.\n3. Using the Simon XTi Panel\na. Enter System Programming.\nb. Select Interactive Services.\nc. Select Z-Wave.\nd. Select Delete Device.\ne. Trigger a device to remove it from the network.\nf. When a device is deleted successfully and its network information is erased, the panel will beep.\ng. You will need to re-enter Delete Mode before triggering the next device",
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\n1.3 Reset Alarm.com Module to default state\nNOTE: This function will forcibly clear the Alarm.com module's Z-Wave node identification and will also remove all network information from the module.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page.\n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the module to act on them",
+		"inclusion": "1. Enter System Programming.\n2. Select Interactive Services.\n3. Select Z-Wave.\n4. Select Add Device.\n5. Trigger a device to add it to the network.\n6. When a device is added successfully, the panel will beep.",
+		"exclusion": "1. Enter System Programming.\n2. Select Interactive Services.\n3. Select Z-Wave.\n4. Select Delete Device.\n5. Trigger a device to remove it from the network.\n6. When a device is deleted successfully and its network information is erased, the panel will beep.",
+		"reset": "1. Navigate to the Equipment page.\n2. Click the 'emPower Devices' tab.\n3. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n4. Click on the 'Reset To Factory Default' button.\n5. Allow 3 minutes for the associated commands to go through and for the module to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1686/SimonXT_XTi_VoLTEModule_InstallGuide_EN_ZWVP.pdf"
 	}
 }

package/config/devices/0x0094/adc-470l.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "NOTE: This function will forcibly clear the Alarm.com ADC-470L's Z-Wave node identification and will also remove all network information from the ADC-470L. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-470L to act on them",
+		"reset": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n5. Click on the 'Reset To Factory Default' button.\n6. Allow 3 minutes for the associated commands to go through and for the ADC-470L to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2297/Alarm.com%20ADC-470L%20Z-Wave%20Documentation%20v1.docx"
 	}
 }

package/config/devices/0x0094/adc-620t.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-620T's Z-Wave node identification and will also remove all network information from the ADC-620T. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-620T to act on them",
+		"reset": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n5. Click on the 'Reset To Factory Default' button.\n6. Allow 3 minutes for the associated commands to go through and for the ADC-620T to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3176/Alarm.com%20ADC-620T%20Z-Wave%20Documentation%2012_11_18v2.pdf"
 	}
 }

package/config/devices/0x0094/adc-nk-100t.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nThis resets the Hub to its factory settings.\nCAUTION: Factory Resetting erases all\ndevices and settings.\nNOTE: The command to enable or disable\nFactory Resetting can be sent from the\nAlarm.com Dealer Website's AirFX Toolkit.\nFactory Resetting is only available during\nthe first 120 seconds after initially powering\non the Hub.\n• After entering Advanced Mode, press and hold the\nEnrollment button ( ) for 10 seconds. When the\nreset process has begun, the Status Light will blink\norange slowly and the Hub will beep five times.\n• To cancel Factory Resetting, you must\nimmediately press and release the Enrollment\nbutton ( ). This feature is only available\nduring the first five seconds after Factory\nResetting has begun.\n• When Factory Resetting is complete, the Status\nLight will shine solid orange for 10 seconds.\n• Next, contact Alarm.com Customer Support to\nreinitialize the Hub",
+		"reset": "1. After entering Advanced Mode, press and hold the Enrollment button for 10 seconds.\n2. When the reset process has begun, the Status Light will blink orange slowly and the Hub will beep five times.\n3. To cancel, immediately press and release the Enrollment button within the first five seconds.\n4. When complete, the Status Light will shine solid orange for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1760/ADC_BB_hub_user_manual_060316.pdf"
 	}
 }

package/config/devices/0x0094/adc-sg130z.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "This process will clear all nodes from the Alarm.com Z-Wave device's network, change the Alarm.com Z-Wave device's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps:\n\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'Z-Wave Devices' tab.\n4. Under the 'Advanced Z-Wave Commands' header, click 'Remove All Z-Wave Devices.'\n5. Allow 3 minutes for the associated commands to go through and for the Alarm.com Z-Wave\ndevice to act on them.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only if the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'Z-Wave Devices' tab.\n4. Under the 'Advanced Z-Wave Commands' header, click 'Remove All Z-Wave Devices.'\n5. Allow 3 minutes for the associated commands to go through and for the device to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4151/Alarm.com-SupplementalZ-WaveDocumentationv6_9_2.pdf"
 	}
 }

package/config/devices/0x0094/adtzwm_for_comman.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-SG-100Z's Z-Wave node identification and will also remove all network information from the ADC-SG-100Z. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-SG-100Z to act on them",
+		"reset": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n5. Click on the 'Reset To Factory Default' button.\n6. Allow 3 minutes for the associated commands to go through and for the ADC-SG-100Z to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3214/Alarm.com%20ADC-SG-100Z%20Z-Wave%20Documentation%2001_24_19.pdf"
 	}
 }

package/config/devices/0x0094/ht-138s.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "NOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com GATEWAY will have network information replicated over to them. \n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices to their final location on the property. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Add Z-Wave Devices \nf. Wait for the bolded message: Checking for new devices on the network \ng. Trigger a device to add it to the network. \nh. When a device is added successfully, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page. \nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List. \nd. Click Add Z-Wave Devices. \ne. Wait for the bolded message: Checking for new devices on the network. \nf. Trigger a device to add it to the network. \ng. When a device is added successfully, it will show up on this screen following a 30 second delay. \nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.",
-		"exclusion": "1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Remove Z-Wave Devices \nf. Wait for the bolded message: Checking for removed devices on the network \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY.\nb. Navigate to the Equipment page. \nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List. \ne. Click Remove Z-Wave Devices. \nf. Wait for the bolded message: Checking for removed devices on the network. \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.",
-		"reset": "2.4 Reset Alarm.com Z-WAVE DEVICE to default state\n\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE's network, change the Alarm.com Z-WAVE DEVICE's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps: 1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n\n2. Navigate to the 'Equipment' page.\n\n3. Click the 'emPower Devices' tab.\n\n4. Expand the 'Advanced Z-Wave Commands' box.\n\n5. Click the 'Remove All Z-Wave Devices' button.\n\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act on them",
+		"inclusion": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the emPower Devices tab.\n4. Open the Advanced Z-Wave Commands menu below the Equipment List.\n5. Click Add Z-Wave Devices.\n6. Trigger a device to add it to the network.",
+		"exclusion": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the emPower Devices tab.\n4. Open the Advanced Z-Wave Commands menu below the Equipment List.\n5. Click Remove Z-Wave Devices.\n6. Trigger a device to remove it from the network.",
+		"reset": "1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'emPower Devices' tab.\n4. Expand the 'Advanced Z-Wave Commands' box.\n5. Click the 'Remove All Z-Wave Devices' button.\n6. Allow 3 minutes for the associated commands to go through and for the device to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3298/Alarm.com%20Gateway-Supplemental%20Z-WaveDocumentation%20V5%20-%20Bezeq.pdf"
 	}
 }

package/config/devices/0x0094/ws900-29.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "NOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com GATEWAY will have network information replicated over to them. \n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices to their final location on the property. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Add Z-Wave Devices \nf. Wait for the bolded message: Checking for new devices on the network \ng. Trigger a device to add it to the network. \nh. When a device is added successfully, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page. \nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List. \nd. Click Add Z-Wave Devices. \ne. Wait for the bolded message: Checking for new devices on the network. \nf. Trigger a device to add it to the network. \ng. When a device is added successfully, it will show up on this screen following a 30 second delay. \nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.",
-		"exclusion": "1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Remove Z-Wave Devices \nf. Wait for the bolded message: Checking for removed devices on the network \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY.\nb. Navigate to the Equipment page. \nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List. \ne. Click Remove Z-Wave Devices. \nf. Wait for the bolded message: Checking for removed devices on the network. \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.",
-		"reset": "2.6 Reset Alarm.com Z-WAVE DEVICE to default state\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE's network, change the Alarm.com ZWAVE DEVICE's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset,\nfollow these steps:\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'emPower Devices' tab.\n4. Expand the 'Advanced Z-Wave Commands' box.\n5. Click the 'Remove All Z-Wave Devices' button.\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act\non them",
+		"inclusion": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the emPower Devices tab.\n4. Open the Advanced Z-Wave Commands menu below the Equipment List.\n5. Click Add Z-Wave Devices.\n6. Trigger a device to add it to the network.",
+		"exclusion": "1. Visit the Alarm.com dealer site.\n2. Navigate to the Equipment page.\n3. Click the emPower Devices tab.\n4. Open the Advanced Z-Wave Commands menu below the Equipment List.\n5. Click Remove Z-Wave Devices.\n6. Trigger a device to remove it from the network.",
+		"reset": "1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'emPower Devices' tab.\n4. Expand the 'Advanced Z-Wave Commands' box.\n5. Click the 'Remove All Z-Wave Devices' button.\n6. Allow 3 minutes for the associated commands to go through and for the device to act on them.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3784/Alarm.com-SupplementalZ-WaveDocumentationv6.1_new.pdf"
 	}
 }

package/config/devices/0x0099/gws-hr-001.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "A Reboot/Reset button is located on the backside of the AXON™ Home Router. It can easily be identified on the back of the unit by its red color and location directly above the yellow RJ45 Ethernet ports and below the USB ports. Pressing the button will perform one of two functions depending on how long the button is pressed.\n\nA short press will trigger a reboot of the router and will not change any permanent settings.\nA long press (3 second and longer) will trigger a reset operation and then will reboot the AXON™ Home Router. A reset operation will change all router settings including the Z-Wave Controller settings back to its factory default.",
+		"reset": "1. Locate the red Reboot/Reset button on the backside of the router above the yellow RJ45 Ethernet ports.\n2. Press and hold the button for 3 seconds or longer.\n3. The router will reset and reboot automatically.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1609/Final%20INS11796-4-UserGuide%20-%202015-12-28.docx"
 	}
 }

package/config/devices/0x009b/2gig-stz.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Set your primary controller to Include, add or Install mode, to add the thermostat as a node on\n\nyour network (see your controller's user manual for detailed instructions).\n\n2. Touch any button to take the thermostat out of sleep mode.\n\n3. Touch and hold MODE button for 5 seconds. SETUP will be displayed in the status display line.\n\n4. Scroll to 'Z-Wave' using  buttons. Touch FAN (Select).\n\n5. When prompted by your Z-Wave controller, select YES in the Z-Wave Install screen.\n\n6. Touch FAN (Select) to add thermostat to network.\n\n7. The display line should flash WAIT and then SUCCESS if Z-Wave connection is made.\n\n8. If Z-Wave does not connect to controller, WAIT, then FAIL will flash in status display line.\n\n9. If thermostat fails to connect, repeat Steps three (3) through (7) to re-try connecting.\n\nYour controller will indicate the thermostat was successfully added to its network (see your controller's user manual for details). Also, you can check if the thermostat was successfully added to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the thermostat INFO screen.",
-		"exclusion": "Removing from a Z-Wave Network\nTo remove the thermostat from the network, use the following steps.\n1. Set your primary controller to exclude or remove mode to remove the thermostat as a node on\nyour network (see your controller's user manual for detailed instructions).\n2. Touch any button to take the thermostat out of sleep mode.\n3. Touch and hold the MODE button for 5 seconds. SETUP will be displayed in the status display line.\n5. Scroll to 'Z-Wave' using  buttons. Touch FAN (Select).\n6. When prompted by your Z-Wave controller, select YES in the Z-Wave exclude screen.\n7. Touch FAN (Select) to remove thermostat to network.\n8. The display line should flash WAIT then SUCCESS if the thermostat is removed from the network.\n9. If the removal operation is not successful, WAIT will flash, then FAIL will flash in status display\nline. Repeat Steps three (3) through (7) to re-try",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the 2GIG-STZ-1's Z-Wave parameters to Factory Settings (both Z-Wave and HVAC settings):\n1. Touch and hold MODE button to go to Setup menu.\n2. Touch and hold MODE and the down arrow key to enter Advanced Menu.\n3. Navigate to Restore Defaults to perform a factory reset",
+		"inclusion": "1. Touch any button to wake the thermostat\n2. Touch and hold the MODE button for 5 seconds\n3. Scroll to 'Z-Wave' using buttons and touch FAN (Select)\n4. Select YES in the Z-Wave Install screen\n5. Touch FAN (Select)\nThe display will flash WAIT and then SUCCESS if inclusion is successful. WAIT then FAIL will flash if inclusion fails.",
+		"exclusion": "1. Touch any button to wake the thermostat\n2. Touch and hold the MODE button for 5 seconds\n3. Scroll to 'Z-Wave' using buttons and touch FAN (Select)\n4. Select YES in the Z-Wave exclude screen\n5. Touch FAN (Select)\nThe display will flash WAIT then SUCCESS if exclusion is successful. WAIT then FAIL will flash if exclusion fails.",
+		"reset": "1. Touch and hold MODE button to go to Setup menu\n2. Touch and hold MODE and the down arrow key to enter Advanced Menu\n3. Navigate to Restore Defaults to perform a factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3884/10028238%20Rev-E%20-%202GIG-STZ-1%20User%20Guide_PRINT.pdf"
 	}
 }

package/config/devices/0x0106/649496_02012_5.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "To reset the MiFi Secure to factory defaults, push and hold the \"Reset\" button for at least 15 seconds (or until all LED's begin flashing simultaneously). Note: resetting your MiFi Secure will remove it and all associated devices from your Icontrol system, in addition to clearing all communication settings",
+		"reset": "Push and hold the Reset button for at least 15 seconds until all LEDs begin flashing simultaneously.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1562/Activation_Guide_SimonXT_Cellular_Only_13005.22-7.5.0-3302015_0.pdf"
 	}
 }

package/config/devices/0x0106/ch-1000.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "To reset the One Link to factory defaults, push and hold the \"Reset\" button for at least 15 seconds (or until all LED's begin flashing simultaneously). Note: resetting your One Link will remove it and all associated devices from your Icontrol system",
+		"reset": "Push and hold the Reset button for at least 15 seconds until all LEDs begin flashing simultaneously.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1535/One%20Link%20QIG%2010.2015.pdf"
 	}
 }

package/config/devices/0x0106/piper_nv.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave Network Reset\nThe Z-Wave network reset procedure performs a default factory reset on Piper's Z-Wave controller component, which clears all user and Z- Wave network settings. A new Z-Wave network will be established. Afterwards, any previously existing Z-Wave devices must be reset and then added to the new network via the Piper app.\nThe Reset Z-Wave option is located under Settings->Wireless Accessories->Advanced Options\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "In the Piper app, navigate to Settings > Wireless Accessories > Advanced Options and select Reset Z-Wave.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1629/PIP-UserManualContent-291116-0905-386.pdf"
 	}
 }

package/config/devices/0x0108/dch-g020.json

@@ -16,7 +16,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press and hold the 'Reset button' for 5 seconds on DCH‐G020",
+		"reset": "Press and hold the Reset button for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1297/DLink_DCH-G020_manual_v1.1.pdf"
 	}
 }

package/config/devices/0x0108/dch-g021.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "On home tile screen click 'Hub Settings'\nClick 'Advanced Options'\nClick 'Restore' (under Restore to Factory Settings) and follow the on screen instructions.",
+		"reset": "1. On the home tile screen click Hub Settings.\n2. Click Advanced Options.\n3. Click Restore under Restore to Factory Settings and follow the on-screen instructions.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1145/Connect_insert_FINAL_Outline.pdf"
 	}
 }

package/config/devices/0x0108/dch-g022.json

@@ -23,7 +23,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Press and hold the 'Reset button' for 5 seconds on DCH-G022\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold the Reset button for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2052/DLink_DCH-G022_manual%20v2.pdf"
 	}
 }

package/config/devices/0x0108/dch-z112.json

@@ -16,9 +16,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "There is a button on DCH-Z112.\n1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing button once to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "There is a button on DCH-Z112.\n1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing button once to enter the exclusion mode",
-		"reset": "There is a button on DCH-Z112.\n1. Pressing button for about 5 seconds.\n2. IDs are excluded and all settings will reset to factory default.\nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable",
+		"inclusion": "Press the button once.",
+		"exclusion": "Press the button once.",
+		"reset": "Press and hold the button for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2082/Z112_manual.pdf"
 	}
 }