@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x034f/pl2s0s10-zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Tap add device on your app, then back to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"exclusion": "Tap add device on your app, then back to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"reset": "Press the R button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps",
+		"inclusion": "1. Enter programming code and confirm\n2. Press 9 and confirm\n3. 2 long beeps indicate success, 3 short beeps indicate failure",
+		"exclusion": "1. Enter programming code and confirm\n2. Press 9 and confirm\n3. 2 long beeps indicate success, 3 short beeps indicate failure",
+		"reset": "Press the R button for more than 5 seconds until you hear 3 long beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2896/PL2S%20Z-wave%20User%20Guide-2.pdf"
 	}
 }

package/config/devices/0x0353/re6100.json

@@ -15,9 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Navigate to the Devices screen using the left side menu on the Touchpad. \n2. Touch the '+ Add' icon on the top right corner to start adding Z-Wave. \n3. Connect+ will start the addition process and the following messages will display on the right side of the screen. This may take only a few seconds, or up to a minute to complete if the Connect+ controller is busy. \n4. When the second message above is displayed, Connect+ is now ready to add the new device. Follow the new device's instructions to place it into inclusion mode. This is typically a button press.\n5. After putting the device into inclusion mode, the following message will display on the screen. Depending on the device and number of supported command\nclasses, this may take only a few seconds or up to a minute to complete.\n6. If inclusion is successful, Connect+ will begin a device interrogation and gather current device command class states. It may take several seconds to display current device status on the screen. By default, the device's initial name is set to the assigned node number within the Z-Wave network. The following is an example of a typical light switch device",
-		"exclusion": "1.On the Z-Wave device page on the Touchpad, touch the '- Remove' icon in the top right corner.\n2.Connect+ will start the removal process. Status messages will display on the right side of the screen, and follow similar steps to the Add process. You will be prompted to place the device into exclusion mode, which is typically a button press. Follow the device's instructions to place it into exclusion mode.\n3. If removal fails, try again until successful",
-		"reset": "Two types of Z-Wave reset are supported: soft reset and hard reset. Soft reset will only reboot the Z-Wave controller and will retain all your devices. Use this if you are experiencing persistent network issues to attempt to correct them. A hard reset will set the Z-Wave controller in Connect+ back to its factory default and all network devices will be cleared.\n\n1. Navigate to the Settings screen from the left side menu, or the Settings icon on the home screen on the Touchpad.\n2. In the Settings menu, touch the last item 'Panel' and enter your 4-digit security system PIN when prompted.\n3. In the next sub-menu, scroll down and select the 'Z-Wave' menu item.\n4. Select either 'Soft Reset' or 'Hard Reset'. You will see a confirmation message on the screen before performing the reset action.\n5. A hard reset typically takes 5-10 seconds to complete. A soft reset will take additional time to complete refreshing all devices on the network, approximately 30 seconds per enrolled device. On large networks this may take several minutes to complete before normal operation is expected to resume.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Navigate to Settings > Panel (enter PIN) > Z-Wave\n2. Select 'Hard Reset'\n3. Confirm the reset action",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3307/RE6100P%20Installation%20Manual%20Z-Wave%20(1).pdf"
 	}
 }

package/config/devices/0x0369/7440-mc-fs.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Start the adding process on the controller side\n\nOnce started, start the adding process on the Connectair module by pressing 3 times the Z-Wave button, located between the plus and the minus button, using the included tool.\n\nWhen added, the LED will turn off",
-		"exclusion": "Start the removing process on the controller side\nOnce started, put the device in \"learn mode\" by pressing 3 times on the Z-Wave button, located between the plus and the minus button, using the included tool.\nWhen removed, the LED will turn on",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable\n\nHold the Z-Wave button for about ten seconds\nIf it was included, the LED will turn back on when reset is done",
+		"inclusion": "1. Start inclusion\n2. Press the Z-Wave button 3 times (located between + and - buttons)\n3. The LED will turn off when added",
+		"exclusion": "1. Start exclusion\n2. Press the Z-Wave button 3 times\n3. The LED will turn on when removed",
+		"reset": "Hold the Z-Wave button for about 10 seconds. The LED will turn on when reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2965/ICCVUG-120618-2329.pdf"
 	}
 }

package/config/devices/0x0369/cw7.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave Factory reset procedure\nThe 2KLIC controller has an option to factory reset which allows the system to return back to its default settings, the steps are given below:\n\nFrom the home page, click on the property\nClick the System status icon in the left menu\nClick the Smart controller card, which is the first card visible, to edit the smart controller settings\nGo to the Manage Z-Wave tab \nOpen the Advanced options\nFind the Reset card\nClick on the Reset button to start\nClick on the text input and type 'Confirm' in the box below\nThen click on the Confirm button\nYou will see \"The controller is resetting. Please wait. It could take up to 1 minute.\" message\nAnd then you will see \"The controller has been reset\", as soon as it is done resetting\nNow you have to start adding new devices to your controller and take all the necessary steps to get your system up and running.\n\nResetting this controller will leave your Z-Wave devices orphaned in the network. Please remove all Z-Wave devices before performing this reset procedure. If this controller is a part of another Z-Wave network, please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. From home page, click on the property\n2. Click System status icon in left menu\n3. Click Smart controller card\n4. Go to Manage Z-Wave tab > Advanced options\n5. Find Reset card and click Reset button\n6. Type 'Confirm' in the text box and click Confirm\n\nNote: This will orphan all Z-Wave devices. Remove all devices before resetting",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2972/INT-HDW-5401%20Connectair%20CC7%20Controller%20v1%20-%20User%20guide.pdf"
 	}
 }

package/config/devices/0x036f/sentinel_2_0.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, the factory reset operation will result in the nodes in your network being orphaned and it will be necessary after the execution of reset operation to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable. \n\nTo reset the controller, hold the reset button for 16 seconds. This will reset it to factory default.",
+		"reset": "Hold the reset button for 16 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3226/EUGENIO%20manuale%20inglese_v4.2.pdf"
 	}
 }

package/config/devices/0x0371/zwa060.json

@@ -0,0 +1,16 @@
+{
+	"manufacturer": "Aeotec Ltd.",
+	"manufacturerId": "0x0371",
+	"label": "ZWA060",
+	"description": "Z-Stick 10 Pro",
+	"devices": [
+		{
+			"productType": "0x0004",
+			"productId": "0x003c"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	}
+}

package/config/devices/0x037b/gkbc-3100z.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3803/GKBC-3100Z_Z-Wave%20Manual_20200226.pdf"
 	}
 }

package/config/devices/0x037b/gkdl-5000z.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3991/GKDL-5000Z_5100Z_Z-Wave%20Manual_20200826.pdf"
 	}
 }

package/config/devices/0x037b/gkdl-5100z.json

@@ -70,9 +70,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3952/GKDL-5100Z_Z-Wave%20Manual_20200808.pdf"
 	}
 }

package/config/devices/0x037b/gkw-1000z.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [5].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [5]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3191/GKW-1000Z%20Z-Wave%20Manual_English_201801211.pdf"
 	}
 }

package/config/devices/0x037b/gkw-2000.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3064/GKW-2000D%20Z-Wave%20Manual_20180807.pdf"
 	}
 }

package/config/devices/0x037c/pad07-3e.json

@@ -36,7 +36,7 @@
 		{
 			"#": "2",
 			"label": "LED Indication Mode",
-			"description": "1. show dimmer state：when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode：when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
+			"description": "1. show dimmer state: when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode: when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -58,7 +58,7 @@
 		{
 			"#": "3",
 			"label": "External Switch Type",
-			"description": "1. one switch mode：only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode：s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode：s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
+			"description": "1. one switch mode: only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode: s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode: s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -101,9 +101,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing Include button of PAD07 three times within 2 seconds will enter exclusion mode.\n3. Node ID has been excluded.",
-		"reset": "1. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press Include button of PAD07 again for 5 seconds.\n3. IDs are excluded.\n\n*Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Include button three times within 2 seconds",
+		"exclusion": "Press the Include button three times within 2 seconds",
+		"reset": "Press the Include button three times within 2 seconds. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2935/PAD07%20manual-20180426.pdf"
 	}
 }

package/config/devices/0x037c/psm08-3e.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing button once to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing button once to enter the exclusion mode",
-		"reset": "There is a button on PSM08.\n1. Pressing button for about 5 seconds.\n2. IDs are excluded and all settings will reset to factory default.\nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable",
+		"inclusion": "Press the button once",
+		"exclusion": "Press the button once",
+		"reset": "Press the button for about 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2940/PSM08_manual-20161103.pdf"
 	}
 }

package/config/devices/0x038e/tfw-01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "• To add the unit to the network, put the controller (purchased separately) into the pairing/add/inclusion mode and then press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash to indicate it's in the pairing mode. When the blue light goes solid, the unit has been included in the network. If the blue light is not illuminated, the unit is not part of a network",
-		"exclusion": "• To remove the unit from a network put the controller (purchased separately) into the pairing/removal/exclusion mode and then press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash and will go out when the device is removed from the network",
-		"reset": "• This device will perform a Z-Wave factory reset when the exclusion process stated above is followed. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash during pairing and turn solid when inclusion is complete.",
+		"exclusion": "Press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash and go out when the device is removed.",
+		"reset": "This device will perform a factory reset when the exclusion process is followed.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2995/Wireless%20Detector%20Manual%20Rev%20H.pdf"
 	}
 }

package/config/devices/0x039a/INT-SMDWD-01.json

@@ -87,9 +87,9 @@
 	],
 	"metadata": {
 		"wakeup": "Press the button briefly",
-		"inclusion": "Press the button 3 times within 1.5s to enter inclusion mode.",
-		"exclusion": "Press the button 3 times within 1.5s",
-		"reset": "Press and hold the button for 10s until LED light is on, then release the button.",
+		"inclusion": "Press the button 3 times within 1.5 seconds",
+		"exclusion": "Press the button 3 times within 1.5 seconds",
+		"reset": "Press and hold the button for 10 seconds until LED turns on, then release the button",
 		"manual": "http://downloads.inteset.com/DoorSensorManualS2.pdf"
 	}
 }

package/config/devices/0x039a/INT-SMMD-N1.json

@@ -242,9 +242,9 @@
 	],
 	"metadata": {
 		"wakeup": "Press the button briefly",
-		"inclusion": "Press the button 3 times within 1.5s to enter inclusion mode.",
-		"exclusion": "Press the button 3 times within 1.5s",
-		"reset": "Press and hold the button for 10s until LED light is on, then release the button.",
+		"inclusion": "Press the button 3 times within 1.5 seconds",
+		"exclusion": "Press the button 3 times within 1.5 seconds",
+		"reset": "Press and hold the button for 10 seconds until LED turns on, then release the button",
 		"manual": "http://downloads.inteset.com/Motion2In1ManualS2.pdf"
 	}
 }

package/config/devices/0x039b/uzw4010tim2.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "With the Factory Reset server method it is possible to clear TIM Box device list. This cause z-wave devices removal from mobile and STB application but not their reset. To complete device reset, it is necessary to reset all z-wave devices physically.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3781/IoTIM%20-%20Quick%20Guide.pdf"
 	}
 }

package/config/devices/0x0407/ls090wh.json

@@ -21,7 +21,7 @@
 	},
 	"metadata": {
 		"inclusion": "Inclusion\n\n1. Click '+' on the upper right corner\n\n2. Select 'Z-Wave'\n\n3. Choose 'Add'\n\n4. Waiting for the procedure to finish\n\n5. Select security level\n\n6. Input DSK code",
-		"exclusion": "Exclusion\n\n1. Choose device on homepage\n\n2. Select '...' on the upper right corner\n\n3. Choose ‘Remove'",
+		"exclusion": "Exclusion\n\n1. Choose device on homepage\n\n2. Select '...' on the upper right corner\n\n3. Choose 'Remove'",
 		"reset": "Factory Reset\n1. Click '+' on the upper right corner\n2. Select 'Z-Wave'\n3. Choose 'Reset'\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3644/Smart%20Station%20User%20Manual.pdf"
 	}

package/config/devices/0x040b/pgzng1-2adnas.json

@@ -15,9 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To add a Z-Wave Device:\n1. Click Pulse Devices, and then click Switches, Door Locks, Thermostats, Others.\nThe Z-Wave Devices list screen appears.\n2. Click Add.\n3. Click the Z-Wave device's 'include' button. If you are adding a Z-Wave device with S2 security to an in-home gateway model number PGZNG1 v2, a dialog will prompt you for the 5-digit DSK (Device Specific Key).\n4. Follow the instructions on the dialog:\na. Locate the 5-digit DSK on the Z-Wave device.\nb. Enter the 5-digit DSK.\nc. For assistance in locating the DSK, click the information (i) icon on the dialog.\nd.Press Continue.\n5. Click on the newly added Z-Wave device list item.\n6. In the Name field, enter a name for the Z-Wave device, and then click Save.",
-		"exclusion": "To remove a Z-Wave device, click on the device in the Z-Wave Devices list to open the Z-Wave Device Details screen. Click the Remove button",
-		"reset": "To reset the device, press and hold the reset button on the back of the unit for about 15 seconds. The unit will then restart.\n\nNote: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and re-add all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this\nCopyright © 2014-2018 ICN Acquisition, LLC. All rights reserved.\nprocedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold the reset button on the back of the unit for about 15 seconds until the unit restarts",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3665/Z-Wave%20Plus%20Guide%2009-23-19.pdf"
 	}
 }

package/config/devices/0x040d/zw100.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Open the App mCamviewZ+ and go to \"Home Settings\" > \"Camera settings\" > \"Admin\" > \"Z-Wave administrator\" page, click \"Z-Wave Reset\" will reset the Z-Wave Settings of the camera.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.",
+		"reset": "Open the App mCamviewZ+ and go to Home Settings > Camera settings > Admin > Z-Wave administrator page, then click Z-Wave Reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3072/ZW100%20Quick%20Install%20Guide%20AND%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x040d/zw300.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Tap \"add device\" on your app, then tap enter to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"exclusion": "Tap \"remove device\" on your app, then tap enter to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"reset": "Press the R button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press Enter on the lock\n2. Enter programming code and confirm\n3. Enter 9 and confirm\n4. Two long beeps indicate successful programming, three short beeps indicate failure",
+		"exclusion": "1. Press Enter on the lock\n2. Enter programming code and confirm\n3. Enter 9 and confirm\n4. Two long beeps indicate successful programming, three short beeps indicate failure",
+		"reset": "Press and hold the R button for more than 5 seconds until you hear 3 long beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3074/ZW300%20Smartlock%20Manual_Sept2018%20v2.pdf"
 	}
 }

package/config/devices/0x040f/rs-zwirex1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Push the Learn mode button once. Wait about 15 seconds",
-		"exclusion": "Push Z-Wave Learn mode button once. Wait about 5 seconds",
-		"reset": "Push Z-wave Learn mode button for 5 seconds",
+		"inclusion": "Press the Learn mode button once",
+		"exclusion": "Press the Learn mode button once",
+		"reset": "Press and hold the Learn mode button for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3465/QuickGuide_ZWIREX1_0703.pdf"
 	}
 }

package/config/devices/0x041a/kp-sw-07.json

@@ -54,9 +54,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "• Connect the power supply. \n• Set the Z-Wave network main controller into learning mode. \n• Press and hold the button 1 (the red light flashes slowly) until the pink light flashes slowly and then release, the device sends the network k information (blue light flashes quickly). \n• After the network is successfully connected, the LED indicator of the device is steady blue, and the load is off by default.",
-		"exclusion": "• Power on the switch. \n• Set the Z-Wave network controller into the exclusion mode. \n• Long press the switch button 1 (Red LED blink slowly) when Pink LED indicator light blink slowly, release the button, then the device start to send out exclusion information(Blue LED indicator in quick blinking). \n• When exclusion successfully, LED display is steady blue, load is off.",
-		"reset": "Reset procedure will delete all information in the Z-Wave network or Z-Wave gateway, and will restore switch to factory default settings. \n• Make sure switch is powered. \n• Press and hold the Switch button 1 for 20 seconds. \n• Until the pink light is always on, release the button. \n Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Connect the power supply\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when successfully connected",
+		"exclusion": "1. Power on the switch\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when exclusion is successful",
+		"reset": "1. Ensure the switch is powered\n2. Press and hold button 1 for 20 seconds\n3. Release the button when the pink LED is always on",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3580/KP-SW-07user%20manual.pdf"
 	}
 }

package/config/devices/0x041a/kp-sw-08.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "• Connect the power supply. \n• Set the Z-Wave network main controller into learning mode. \n• Press and hold the button 1 (the red light flashes slowly) until the pink light flashes slowly and then release, the device sends the network k information (blue light flashes quickly). \n• After the network is successfully connected, the LED indicator of the device is steady blue, and the load is off by default.",
-		"exclusion": "• Power on the switch. \n• Set the Z-Wave network controller into the exclusion mode. \n• Long press the switch button 1 (Red LED blink slowly) when Pink LED indicator light blink slowly, release the button, then the device start to send out exclusion information(Blue LED indicator in quick blinking). \n• When exclusion successfully, LED display is steady blue, load is off.",
-		"reset": "Reset procedure will delete all information in the Z-Wave network or Z-Wave gateway, and will restore switch to factory default settings. \n• Make sure switch is powered. \n• Press and hold the Switch button 1 for 20 seconds. \n• Until the pink light is always on, release the button. \n Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Connect the power supply\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when successfully connected",
+		"exclusion": "1. Power on the switch\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when exclusion is successful",
+		"reset": "1. Ensure the switch is powered\n2. Press and hold button 1 for 20 seconds\n3. Release the button when the pink LED is always on",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3587/KP-SW-08.pdf"
 	}
 }

package/config/devices/0x041b/39446_zw3107.json

@@ -133,8 +133,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\ndimmer. Repeat as necessary to add the dimmer to\nthe network.\nYou have complete control",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\ndimmer to remove it from the network",
-		"reset": "1. If plugged in, unplug the dimmer from the receptacle\n2. Press and hold the top button, plug the device in and\ncontinue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart dimmer.",
+		"exclusion": "Press and release the manual/program button on the smart dimmer.",
+		"reset": "1. If plugged in, unplug the dimmer from the receptacle\n2. Press and hold the top button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39449_zw4106.json

@@ -58,8 +58,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\nswitch. Repeat as necessary to add the switch to\nthe network",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\nswitch to remove it from the network",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in and\ncontinue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart switch.",
+		"exclusion": "Press and release the manual/program button on the smart switch.",
+		"reset": "1. If plugged in, unplug the device from the receptacle\n2. Press and hold the top button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39453_zw4203.json

@@ -79,8 +79,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\nswitch to add it in the network.\n3. The controller's app will indicate if it has discovered the\nswitch. If prompted by the controller to enter the S2\nsecurity code, refer to the QR code/security number on\nthe side of the box or the QR code label on the product\n(see Figure 1). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\nswitch to remove it from the network",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the manual/program button, plug the\ndevice in and continue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart switch.",
+		"exclusion": "Press and release the manual/program button on the smart switch.",
+		"reset": "1. If plugged in, unplug the device from the receptacle\n2. Press and hold the manual/program button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39455_zw4008.json

@@ -78,9 +78,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the smart switch (rocker) to add it in the network.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the smart switch (rocker) to remove it from the network",
-		"reset": "Quickly press ON (top) button three times, then, immediately press the OFF (bottom) button three times. The LED indicator will flash ON/OFF five times when completed successfully.\nNOTE: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the switch.",
+		"exclusion": "Press and release the top or bottom of the switch.",
+		"reset": "1. Quickly press the top button three times\n2. Immediately press the bottom button three times\n3. The LED will flash ON/OFF five times when completed successfully",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4169/39455_HQSG_v4.pdf"
 	}
 }

package/config/devices/0x041b/39456_zw1002.json

@@ -58,8 +58,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a\ndevice to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the\nprogram button. Repeat as necessary to add the smart outlet to\nthe network.\nYou have complete control",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a\ndevice from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the\nmanual/program button",
-		"reset": "Quickly press the button three times. Then, press the button for at least three\nseconds. The LED will blink five times to confirm.\nNote: This should only be used in the event your network's primary controller\nis missing or otherwise inoperable"
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. Quickly press the button three times\n2. Press the button for at least three seconds\n3. The LED will blink five times to confirm"
 	}
 }

package/config/devices/0x041b/39458_zw3010.json

@@ -142,8 +142,7 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "This dimmer is SmartStart enabled. If your controller supports SmartStart inclusion, this dimmer can be added into the Z-Wave network by following the instructions for your controller or hub and scanning the Z-Wave QR Code on the front or on the package when instructed. No further action is required, and the dimmer will be added automatically within 10 minutes of being powered up while in range Z-Wave network.",
-		"exclusion": "Press on 2 times and off 2 times. LED will flash 5 times if exclusion was successful.",
-		"reset": "Quickly press ON button 3 times then immediately press the Off button 3 times. The LED will flash ON/OFF 5 times when completed successfully"
+		"exclusion": "Press ON 2 times and OFF 2 times (LED will flash 5 times if successful).",
+		"reset": "1. Quickly press ON button 3 times\n2. Immediately press the OFF button 3 times\n3. The LED will flash ON/OFF 5 times when completed successfully"
 	}
 }

package/config/devices/0x041b/proa7pl.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If the Control Panel is the primary controller for your network, resetting it results in the devices in your\nnetwork to be orphaned and is necessary after the reset to exclude and re-include all the devices in the network. This defaults the Z-Wave Controller in the system which removes all programmed Z-Wave devices, however, the devices do not receive a signal to be excluded. So, when they need to be included, they need to be excluded first",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3675/800-25080A_PROA7PLUS_UG.PDF"
 	}
 }

package/config/devices/0x041b/tuxedow.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. At the TUXEDOW Home screen:\n a) Press the Devices icon and then press the SETUP icon to display 'Z-Wave Device Management' screen.\n b) Press the ADD DEVICE icon.\n2. At the device Module:\na) Press the Function Key on the device",
-		"exclusion": "1. At the TUXEDOW Home screen:\n a) Press the Devices and Setup icons to display the 'Z-Wave Device Management' screen.\n b) Highlight the device to remove and press the Remove Device icon.\n2. At the device module:\n a) Press the Function Key to remove the device from the keypad",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nTo activate the Keypad Reset function, press the Setup, System Setup and Advanced Setup icons\n\n1. Enter your Authorized Code and press the Keypad Reset icon.\n\n2. Select OK or Cancel",
+		"inclusion": "Press the Function Key on the device.",
+		"exclusion": "Press the Function Key on the device.",
+		"reset": "1. Press the Setup, System Setup and Advanced Setup icons\n2. Enter your Authorized Code and press the Keypad Reset icon\n3. Confirm with OK",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3624/800-25178B_QIG_TUXEDOW.pdf"
 	}
 }

package/config/devices/0x041c/51110.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Click [Add] icon in Z-Wave Controller.\n- Press the SW_Button 3 times within 1.5s, Blue LED is Blinking 3 times within 1 second.\n- If add Process is successful, Blue LED will turn off.",
-		"exclusion": "- Click [Remove] icon in Z-Wave Controller. \n- Press the SW_Button 3 times within 1.5s \n- If remove Process is successful, blue LED is Blinking 6 times, then turn off.",
-		"reset": "- Long press SW_Button at least 10 seconds. \n- Device Reset Locally notification is Transmitted.\n-Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (blue LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (blue LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3262/51110_manual_EN_NO_SV20190425.pdf"
 	}
 }

package/config/devices/0x041c/51111.json

@@ -32,9 +32,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "-Press Func_Button 3 time in the motion sensor, Green LED is Blinking 3 times within 1 second.\n-If Inclusion Process is successful, Green LED will turn off.",
-		"exclusion": "-Press Func_Button 3 times quickly.\n-If Exclusion Process is successful, Green LED is Blinking 6 times, then turn off.",
-		"reset": "-Long press Func_Button while installing batteries \n-Device Reset Locally notification is Transmitted\n-Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times quickly (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button while installing batteries.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3275/51111%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041c/51112.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.\n- If Inclusion Process is successful, Green LED will turn off.",
-		"exclusion": "- Press the Net_Button 3 times within 1.5s. \n- If Exclusion Process is successful, Green LED is Blinking 6 times, then turn off.",
-		"reset": "- Long press Net_Button at least 10 seconds in the product. \n- Device Reset Locally notification is Transmitted.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3361/51112%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041c/51114.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.\n- If Inclusion Process is successful, Green led will turn off.",
-		"exclusion": "- Press the Net_Button 3 times within 1.5s. \n- If Exclusion Process is successful, Green led is Blinking 6 times, then turn off.",
-		"reset": "- Long press Net_Button at least 10 seconds in the product. \n- Device Reset Locally notification is Transmitted.\n- Please use this procedure only when the network primary controller is missing or otherwise.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3365/51114%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041e/eih-100e.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- This is the Z-Wave Set Default network operation and a confirmation message appears.\n- If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3569/EIH-100E_User_Manual.pdf"
 	}
 }