@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x019a/11-01-011.json

@@ -62,10 +62,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Set your controller in include mode. Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds. A long LED blink indicates that the inclusion was successful.",
-		"exclusion": "Set your controller in exclude mode. Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds. A long LED blink indicates that the exclusion was successful.",
-		"wakeup": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, A LED blink indicates success.",
-		"reset": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, but on the 3rd repetition, leave the magnet at the rounded edge for 10 seconds. A long LED signal indicates success.",
+		"inclusion": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A long LED blink indicates successful inclusion",
+		"exclusion": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A long LED blink indicates successful exclusion",
+		"wakeup": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A LED blink indicates success",
+		"reset": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds, but on the 3rd repetition, leave the magnet at the rounded edge for 10 seconds\n4. A long LED signal indicates success",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=Manuals/3388/Strips%20Guard%20EU%20R3.pdf"
 	}
 }

package/config/devices/0x019a/11_01_022.json

@@ -130,10 +130,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Set your controller in include mode (see your controller's manual). Follow the instruction below for Wake up. A long LED blink indicates that the inclusion was successful.\n\nTo wake up Strips manually for communication with the Z-Wave controller, move the magnet towards and away from the rounded edge. Repeat 3 times.",
-		"exclusion": "Set your controller in exclude mode (see your controller's manual). Follow the instruction below for Wake up. A long LED blink indicates that the exclusion was successful.\n\nTo wake up Strips manually for communication with the Z-Wave controller, move the magnet towards and away from the rounded edge. Repeat 3 times.",
-		"reset": "You may need to reset Strips if your Z-Wave controller is missing or not responding.\n\nFollow the instructions for 'Wake up' above, but on the 3rd repetition, keep the magnet at the rounded edge for 10 seconds. A long LED signal indicates success",
-		"wakeup": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, A LED blink indicates success.",
+		"inclusion": "Move the magnet towards and away from the rounded edge, then repeat 3 times. A long LED blink indicates successful inclusion.",
+		"exclusion": "Move the magnet towards and away from the rounded edge, then repeat 3 times. A long LED blink indicates successful exclusion.",
+		"reset": "1. Move the magnet towards and away from the rounded edge\n2. Repeat 3 times\n3. On the 3rd repetition, keep the magnet at the rounded edge for 10 seconds\n4. A long LED signal indicates success",
+		"wakeup": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A LED blink indicates success",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4300/Strips%20Drip%20700%20manual.pdf"
 	}
 }

package/config/devices/0x019a/11_02_011.json

@@ -337,10 +337,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Set your controller in include mode (see your controller's manual). Follow the instruction below for Wake up. A long LED blink indicates that the inclusion was successful.\n\nTo wake up Strips manually for communication with the Z-Wave controller, move the magnet towards and away from the rounded edge. Repeat 3 times.",
-		"exclusion": "Set your controller in exclude mode (see your controller's manual). Follow the instruction below for Wake up. A long LED blink indicates that the exclusion was successful.\n\nTo wake up Strips manually for communication with the Z-Wave controller, move the magnet towards and away from the rounded edge. Repeat 3 times.",
-		"reset": "You may need to reset Strips if your Z-Wave controller is missing or not responding.\n\nFollow the instructions for 'Wake up' above, but on the 3rd repetition, keep the magnet at the rounded edge for 10 seconds. A long LED signal indicates success",
-		"wakeup": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, A LED blink indicates success.",
+		"inclusion": "Move the magnet towards and away from the rounded edge, then repeat 3 times. A long LED blink indicates successful inclusion.",
+		"exclusion": "Move the magnet towards and away from the rounded edge, then repeat 3 times. A long LED blink indicates successful exclusion.",
+		"reset": "1. Move the magnet towards and away from the rounded edge\n2. Repeat 3 times\n3. On the 3rd repetition, keep the magnet at the rounded edge for 10 seconds\n4. A long LED signal indicates success",
+		"wakeup": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A LED blink indicates success",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3346/Strips%20Multi-Sensors%20EU%20manuals.pdf"
 	}
 }

package/config/devices/0x019a/11_02_022.json

@@ -299,10 +299,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Place the controller into inclusion mode and perform the \"wake up\" pattern as described below.\n\n1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away.\n2. Repeat this 3 times. A final short blink will confirm that the user-command was successful",
-		"exclusion": "Place the controller into exclusion mode and perform the \"wake up\" pattern as described below.\n\n1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away.\n2. Repeat this 3 times. A final short blink will confirm that the user-command was successful",
-		"reset": "You may need to reset Strips if your Z-Wave controller is missing or not responding. Follow the instructions for Wake Up above, but on the 3rd\nrepetition, keep the magnet at the rounded edge for 10 seconds. A long LED signal indicates success",
-		"wakeup": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, A LED blink indicates success.",
+		"inclusion": "Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away and repeat this 3 times. A final short blink will confirm successful inclusion.",
+		"exclusion": "Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away and repeat this 3 times. A final short blink will confirm successful exclusion.",
+		"reset": "1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away\n2. Repeat this 3 times\n3. On the 3rd repetition, keep the magnet at the rounded edge for 10 seconds\n4. A long LED signal indicates success",
+		"wakeup": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A LED blink indicates success",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4106/Strips%20Comfort%20700%20v1.6.pdf"
 	}
 }

package/config/devices/0x019a/11_04_21_22_28.json

@@ -192,10 +192,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Place the controller into inclusion mode and perform the \"wake up\" pattern as described below.\n1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away.\n2. Repeat this 3 times. A final short blink will confirm that the inclusion was successful",
-		"exclusion": "Place the controller into exclusion mode and perform the \"wake up\" pattern as described below.\n1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away.\n2. Repeat this 3 times. A final short blink will confirm that the exclusion was successful",
-		"reset": "Follow the instructions for Wake Up above, but on the 3rd repetition, keep the magnet at the rounded edge for 10 seconds. A long LED signal indicates success",
-		"wakeup": "Place a magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat a total of 3 times within 10 seconds, A LED blink indicates success.",
+		"inclusion": "Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away and repeat this 3 times. A final short blink will confirm successful inclusion.",
+		"exclusion": "Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away and repeat this 3 times. A final short blink will confirm successful exclusion.",
+		"reset": "1. Take the magnet and move it to the rounded edge and wait for the blink, then move the magnet away\n2. Repeat this 3 times\n3. On the 3rd repetition, keep the magnet at the rounded edge for 10 seconds\n4. A long LED signal indicates success",
+		"wakeup": "1. Place a magnet at the rounded edge\n2. When the LED blinks, move the magnet away\n3. Repeat a total of 3 times within 10 seconds\n4. A LED blink indicates success",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4301/Strips%20Drip%20700%20manual.pdf"
 	}
 }

package/config/devices/0x019b/4512688.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the Function button 3 times. The Smoke Detector will emit a 2-tone beep and the LED will turn on for ~2 seconds. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.",
-		"exclusion": "1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1.5 seconds, press the Function button 3 times and the Smoke Detector will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\nPress and hold the button of the smoke detector for 20 seconds. Release the button when you hear 3 beeps to perform factory reset.",
+		"inclusion": "Press the function button 3 times within 1.5 seconds. The smoke detector will emit a 2-tone beep and the LED will turn on for ~2 seconds.",
+		"exclusion": "Press the function button 3 times within 1.5 seconds and the smoke detector will be removed from the Z-Wave network.",
+		"reset": "Press and hold the button of the smoke detector for 20 seconds then release the button when you hear 3 beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4064/Heatit%20Z-Smoke%20Battery%2020201214.pdf"
 	}
 }

package/config/devices/0x019b/4512689.json

@@ -35,9 +35,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Please refer to your primary controller manual on how to enter add/remove mode. The device may only be added or removed from the network if the primary controller is in add/remove mode, and may now be added to the system via the primary controller",
-		"exclusion": "Please refer to your primary controller manual on how to enter add/remove mode. The device may only be added or removed from the network if the primary controller is in add/remove mode, and may now be added to the system via the primary controller",
-		"reset": "After the calibration process is finished, you may access the add/remove mode by pressing the function button three times within 1.5 seconds. Removing the device will reset it to factory defaults",
+		"inclusion": "Press the function button three times within 1.5 seconds.",
+		"exclusion": "Press the function button three times within 1.5 seconds.",
+		"reset": "After the calibration process is finished, press the function button three times within 1.5 seconds. Removing the device will reset it to factory defaults.",
 		"manual": "https://media.heatit.com/709"
 	},
 	"compat": [

package/config/devices/0x019b/45_126_86.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Connect the Router into the power socket to power on. \n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n3. Within 1.5 seconds, press the Function Button 3 times.\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete the adding process.\n5. If the sensor has already been added (included) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "1. Put the Z-Wave Gateway or Control Panel into Exclusion mode (please refer to the Z-Wave Gateway or Control Panel manual).\n2. Within 1.5 seconds, press the Function Button 3 times and the Router will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n*. Press and hold the Function Button for 10 seconds to factory reset.",
+		"inclusion": "Connect the Router into the power socket to power on, then within 1.5 seconds, press the Function Button 3 times.",
+		"exclusion": "Within 1.5 seconds, press the Function Button 3 times.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3818/Heatit%20Z-Repeater_20200305.pdf"
 	}
 }

package/config/devices/0x019b/leakage-stopper.json

@@ -289,9 +289,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Set your Z-Wave Gateway into Inclusion mode / Add device.\ni. Start: Short press Touch Sense Button 3 times.\nii. Processing: Yellow LED and short beep sound keeping continue. For security inclusion support, you may need to entering first 5 digit\nthat show on QR Code label, please refer to the instructions of central controller.\niii. Success: Green LED on 1 second with 2 short beep sounds.\niv. The LED indication changes to Green LED slow blinking from Yellow LED blinking.",
-		"exclusion": "Set your Z-Wave Gateway into Exclusion mode / Remove device.\ni. Start: Short press Touch Sense Button 3 times.\nii. Processing: Yellow LED and short beep sound keeping continue.\niii. Success: Green LED on 1 second with 2 short beep sounds.\niv. The LED indication Changes to Yellow LED blinking",
-		"reset": "Start: Long hold Touch Sense Button for 10 seconds then short click 5 times.\nii. Processing: Yellow LED ON 1 second then wait 2-5 seconds.\niii. Success: Green LED on 2 second with long beep sounds for 2 seconds.\n*Factory Default Reset will:\na. Remote the BVS from Z-Wave Network;\nb. Delete the association setting;\nc. Restore the configuration settings to the default",
+		"inclusion": "Short press Touch Sense Button 3 times.",
+		"exclusion": "Short press Touch Sense Button 3 times.",
+		"reset": "Long hold Touch Sense Button for 10 seconds, then short click 5 times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3885/BVS_ZWU_v1.0.9.pdf"
 	}
 }

package/config/devices/0x019b/tf016_tf021.json

@@ -264,9 +264,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Press Center (confirm) for 10 seconds. The display will show OFF.\n2. Press Right (down) 4 times till you see Con in the display.\n3. Press Center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display.\n4. Confirmation will show Inc/EcL in the display. If inclusion fails, Err (error) will appear.\n5. Leave programming mode by choosing ESC in menu",
-		"exclusion": "1. Press Center (confirm) for 10 seconds. The display will show OFF.\n2. Press Right (down) 4 times till you see Con in the display.\n3. Press Center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display.\n4. Confirmation will show Inc/EcL in the display. If exclusion fails, Err (error) will appear.\n5. Leave programming mode by choosing ESC in menu",
-		"reset": "Press buttons Left and Center (up and confirm) for 20 seconds",
+		"inclusion": "1. Press center (confirm) for 10 seconds. The display will show OFF\n2. Press right (down) 4 times till you see Con in the display\n3. Press center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display\n4. Confirmation will show Inc/EcL in the display. If inclusion fails, Err (error) will appear\n5. Leave programming mode by choosing ESC in menu",
+		"exclusion": "1. Press center (confirm) for 10 seconds. The display will show OFF\n2. Press right (down) 4 times till you see Con in the display\n3. Press center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display\n4. Confirmation will show Inc/EcL in the display. If exclusion fails, Err (error) will appear\n5. Leave programming mode by choosing ESC in menu",
+		"reset": "Press buttons left and center (up and confirm) for 20 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1234/Manual_Multireg%20Z-Wave_Ver2015-A.pdf"
 	}
 }

package/config/devices/0x019b/z-dim2.json

@@ -212,8 +212,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode. \n\nMethod 1: Standard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been added to the network. To start the configuration process press the Reset button, or the external switch connected to P, 3 times in rapid succession. The LED will blink green for 3 seconds if adding is successful. The device is now ready for use with default settings",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings.\n\nRemove mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been removed from the network. To start the configuration process press the Reset button, or the external switch connected to P, 3 times in rapid succession. The LED will blink green for 3 seconds if removing is successful. The device is now ready for use with default settings",
-		"reset": "Press and hold the reset button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will shine solid green for 3 seconds. You may now release the button.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press the Reset button or the external switch connected to P 3 times in rapid succession.",
+		"exclusion": "Press the Reset button or the external switch connected to P 3 times in rapid succession.",
+		"reset": "Press and hold the reset button for 20 seconds until LED shines solid green."
 	}
 }

package/config/devices/0x019b/z-han2.json

@@ -165,8 +165,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added in the network if the primary controller is in add mode. \nWe recommend adding the device within a 2m range from the gateway.\n\nMethod 1: Standard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been added to/removed from the network.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up in green for 3 seconds if adding is successful. The device is now ready for use with default settings",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings.\nWe recommend removing the device within a 2m range from the gateway.\n\nStandard (Manual)\nRemove mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been removed from the network.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up in green for 3 seconds if removing is successful. The device is now ready for use with default settings",
-		"reset": "Press and hold the reset button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will shine solid green for 3 seconds. You may now release the button.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press the reset button 3 times in rapid succession.",
+		"exclusion": "Press the reset button 3 times in rapid succession.",
+		"reset": "Press and hold the reset button for 20 seconds until LED shines solid green."
 	}
 }

package/config/devices/0x019b/z-ph_wall_controller.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode. \n\nThere are two ways to add the device to a Z-Wave network.\n\nMethod 1: Standard (Manual)\nInitiate the learning mode in the controller.\nPress any UP button 6 times within 3 seconds. \n\nWhen the add mode has started, the LED corresponding to the button you pressed will blink green. The device will indicate 'Success' by emitting a green light for 3 seconds. \n\nMethod 2: SmartStart (Automatic)\nSmartStart-enabled products may be added to a Z-Wave network by scanning the Z-Wave QR-Code on the product if your primary controller supports SmartStart inclusion. No further action is required and the SmartStart product will be added automatically after being powered on within range of the primary controller.",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. \nWhen the device is removed from the network, it will NOT revert to factory settings.",
-		"reset": "To factory reset the device, remove the battery from the device. Press and hold any button on the device and repower the device. The LEDs will start blinking 3 times before lighting up in green. When the green LED is on, you can release the button. The device will issue a Device Reset Locally Notification Command to notify that the device will be reset to default. When preforming a factory reset the device will lose its Node ID from the gateway and reset its Home ID.",
+		"inclusion": "Press any UP button 6 times within 3 seconds.",
+		"exclusion": "Press any UP button 6 times within 3 seconds.",
+		"reset": "1. Remove the battery from the device.\n2. Press and hold any button on the device.\n3. Repower the device.\n4. Release the button when the green LED is on.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4028/Manual_Heatit%20Z-Push%20Wall%20Controller_ENG.pdf"
 	}
 }

package/config/devices/0x019b/z-temp3.json

@@ -234,9 +234,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Hold the Center button for 5 seconds. The display will show 'OFF'\n Press the '+' button once to see 'CON' in the display.\n Start the add/remove device process in your primary controller.\n Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds.",
-		"exclusion": "Hold the Center button for 5 seconds. The display will show 'OFF'\n Press the '+' button once to see 'CON' in the display.\n Start the add/remove device process in your primary controller.\n Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds.",
-		"reset": "Enter the menu by holding the Center button for about 5seconds, navigate in the menu with the '+' button til you see FACT. Press the Center button until you see '-- --' blinking in the display, then hold for about 5 seconds to perform a reset. You may also initiate a reset by holding the Right and Center buttons for 55 seconds.",
+		"inclusion": "1. Hold the Center button for 5 seconds.\n2. Press the '+' button once to see 'CON' in the display.\n3. Hold the Center button for approximately 2 seconds.",
+		"exclusion": "1. Hold the Center button for 5 seconds.\n2. Press the '+' button once to see 'CON' in the display.\n3. Hold the Center button for approximately 2 seconds.",
+		"reset": "1. Hold the Center button for about 5 seconds.\n2. Navigate with the '+' button until you see FACT.\n3. Press the Center button until you see '-- --' blinking.\n4. Hold for about 5 seconds to perform a reset.",
 		"manual": "https://media.heatit.com/3872"
 	}
 }

package/config/devices/0x019b/z-trm6.json

@@ -422,9 +422,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Add\nThe primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.\nAn always listening node must be powered continuously and reside in a fixed position in the installation to secure the routing table. Adding the device within a 2 meter range from the gateway can minimize faults during the Interview process.\n\nStandard (Manual)\nAdd mode is indicated on the device by rotating LED segments on the display. It indicates this for 90 seconds until a timeout occurs, or until the device has been added to the network. Configuration mode can also be cancelled by performing the same procedure used for starting\nConfiguration mode.\n1. Hold the Center button for 5 seconds.\nThe display will show 'OFF'.\n2. Press the '+' button once to see 'CON' in the display.\n3. Start the add device process in your primary controller.\n4. Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds.\n\nThe device is now ready for use with default settings.\nIf inclusion fails, please perform a 'remove device' process and try again. If inclusion fails again, please see 'Factory reset'",
-		"exclusion": "Remove\nThe primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode.\nWhen the device is removed from the network, it will NOT revert to factory settings.\n\nStandard (Manual)\nRemove mode is indicated on the device by rotating LED segments on the display. It indicates this for 90 seconds until a timeout occurs, or until the device has been removed from the network. Configuration mode can also be cancelled by performing the same procedure used for starting\nConfiguration mode.\n1. Hold the Center button for 5 seconds.\nThe display will show 'OFF'.\n2. Press the '+' button once to see 'CON' in the display.\n3. Start the remove device process in your primary controller.\n4. Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds.\n\nNB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see Chapter 'Factory reset'",
-		"reset": "Enter the menu by holding the Center button for about 5 seconds, navigate in the menu with the '+' button til you see FACT. Press the Center button until you see '-- --' blinking in the display, then hold for about 5 seconds to perform a reset.\nYou may also initiate a reset by holding the Right and Center buttons for 60 seconds.\n\nWhen either of these procedures has been performed, the thermostat will perform a complete factory reset. The device will display 'RES' for 5 seconds while performing a factory reset. When 'RES' is no longer displayed, the thermostat has been reset.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Hold the Center button for 5 seconds.\n2. Press the '+' button once to see 'CON' in the display.\n3. Hold the Center button for approximately 2 seconds.",
+		"exclusion": "1. Hold the Center button for 5 seconds.\n2. Press the '+' button once to see 'CON' in the display.\n3. Hold the Center button for approximately 2 seconds.",
+		"reset": "1. Hold the Center button for about 5 seconds.\n2. Navigate with the '+' button until you see FACT.\n3. Press the Center button until you see '-- --' blinking.\n4. Hold for about 5 seconds to perform a reset.",
 		"manual": "https://media.heatit.com/2926"
 	}
 }

package/config/devices/0x019b/z-water2.json

@@ -110,9 +110,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added from the network if the primary controller is in add mode. When the device is removed from the network, it will NOT revert to factory settings. An always listening node must be powered continuously and reside in a fixed position in the installation to secure the routing table. Adding the device within a 2 meter range from the gateway can minimize faults during the Interview process.\n\nStandard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the device has been added to the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up solid green for 3 seconds if add is successful. The device is now ready for use with default settings.\nNB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see Chapter 'Factory reset'.\n\nIf inclusion fails, please perform a 'remove device' process and try again. If inclusion fails again, please see 'Factory reset'",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings. An always listening node must be powered continuously and reside in a fixed position in the installation to secure the routing table. \n\nStandard (Manual)\nRemove mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the device has been removed from the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up solid green for 3 seconds if remove is successful. The device is now ready for use with default settings.\nNB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see Chapter 'Factory reset'",
-		"reset": "Press and hold the reset button. After 3 seconds the LED will start to blink green. After 20 seconds the LED will start blinking green rapidly. You may now release the button. If reset was successful the LED will light up solid green for 3 seconds",
+		"inclusion": "1. Press the reset button 3 times in rapid succession\n2. Add mode is indicated on the device by a blinking green LED for 90 seconds until a timeout occurs\n3. The LED will light up solid green for 3 seconds if add is successful",
+		"exclusion": "1. Press the reset button 3 times in rapid succession\n2. Remove mode is indicated on the device by a blinking green LED for 90 seconds until a timeout occurs\n3. The LED will light up solid green for 3 seconds if remove is successful",
+		"reset": "1. Press and hold the reset button\n2. After 3 seconds the LED will start to blink green\n3. After 20 seconds the LED will start blinking green rapidly\n4. Release the button\n5. If reset was successful the LED will light up solid green for 3 seconds",
 		"manual": "https://media.heatit.com/2924"
 	}
 }

package/config/devices/0x019b/zm_dimmer.json

@@ -244,9 +244,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode.\nThe device may only be added from the network if the primary controller is in add mode. When the device is removed from the network, it will NOT revert to factory settings.\nAn always listening node must be powered continuously and reside in a fixed position in the installation to secure the routing table. Adding the device within a 2 meters range from the gateway can minimize faults during the Interview process.\n\nStandard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been added to the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up in solid green for 3 seconds if add is successful. The device is now ready for use with default settings.\n\nNB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see 'Factory reset'.\nIf inclusion fails, please perform a 'remove device' process and try again. If inclusion fails again, please see 'Factory reset'",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings.\n\nStandard (Manual)\nRemove mode is indicated on the device by a blinking green LED. It indicates this for 90 seconds until a timeout occurs, or until the module has been removed from the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode.\nTo start the configuration process, press the reset button 3 times in rapid succession. The LED will light up in solid green for 3 seconds if remove is successful. The device is now ready for use with default settings.\n\nNB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see 'Factory reset'",
-		"reset": "Factory Reset. \nPlease read this before installation.\nPress and hold the reset button. After 3 seconds the LED will start to blink green. After 20 seconds the LED will start blinking green rapidly. You may now release the button. If reset was successful the LED will light up in solid green for 3 seconds.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press the reset button 3 times in rapid succession\n2. Add mode is indicated on the device by a blinking green LED for 90 seconds until a timeout occurs\n3. The LED will light up in solid green for 3 seconds if add is successful",
+		"exclusion": "1. Press the reset button 3 times in rapid succession\n2. Remove mode is indicated on the device by a blinking green LED for 90 seconds until a timeout occurs\n3. The LED will light up in solid green for 3 seconds if remove is successful",
+		"reset": "1. Press and hold the reset button\n2. After 3 seconds the LED will start to blink green\n3. After 20 seconds the LED will start blinking green rapidly\n4. Release the button\n5. If reset was successful the LED will light up in solid green for 3 seconds",
 		"manual": "https://www.thermo-floor.no/media/multicase/documents/_tfasdokumentasjon/heatit%20controls/heatit%20zm%20dimmer%20%20250w/1444449_manual_heatit_zm_dimmer.pdf"
 	}
 }

package/config/devices/0x019b/zm_single_relay_16.json

@@ -194,9 +194,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.\n\nThere are two ways to add the Heatit ZM Single Relay 16A to a Z-Wave network.\n\n*Method 1: Standard (Manual)\nAdd mode is indicated on the device by a blinking green LED. This lasts until timeout occurs after 90 seconds, or until the module has been added to the network.\nThe LED will light up for 3 seconds if adding is successful.\n\nMethod 2: SmartStart (Automatic)\nSmartStart enabled products may be added to a Z-Wave network by scanning the Z-Wave QR-Code on the product if your primary controller supports SmartStart inclusion. No further action is required and the SmartStart product will be added automatically after being powered on within range of the primary controller",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode.\n\nRemove mode is indicated on the device by a blinking green LED. This lasts until timeout occurs after 90 seconds, or until the module has been removed from the network.\nThe LED will light up for 3 seconds if removing is successful",
-		"reset": "Press and hold the configuration button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will stop blinking and emit a constant light. You may now release the button. \n\nNB! Please use this procedure only when the primary controller/ gateway is missing or otherwise inoperable",
+		"inclusion": "1. Add mode is indicated on the device by a blinking green LED\n2. This lasts until timeout occurs after 90 seconds\n3. The LED will light up for 3 seconds if adding is successful",
+		"exclusion": "1. Remove mode is indicated on the device by a blinking green LED\n2. This lasts until timeout occurs after 90 seconds\n3. The LED will light up for 3 seconds if removing is successful",
+		"reset": "1. Press and hold the configuration button\n2. After 3 seconds the LED will start to blink in green\n3. After 20 seconds the LED will stop blinking and emit a constant light\n4. Release the button",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4062/Manual_Heatit%20ZM%20Single%20Relay%2016A_Ver%202020-A_ENG.pdf"
 	}
 }

package/config/devices/0x019b/zm_thermostat_16.json

@@ -143,9 +143,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.\n\nThere are two ways to add the device to a Z-Wave network.\nMethod 1: Standard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been added to the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if adding is successful.\nThe device is now ready for use with default settings.\n\nMethod 2: SmartStart (Automatic)\nSmartStart enabled products may be added to a Z-Wave network by scanning the Z-Wave QR-Code on the product if your primary controller supports SmartStart inclusion. No further action is required and the SmartStart product will be added automatically after being powered on within range of the primary controller.",
-		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode.\n\nRemove mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been removed from the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if removing is successful",
-		"reset": "Press and hold the configuration button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will start to blink green rapidly for 5 seconds. You may now release the button",
+		"inclusion": "Press the configuration button 3 times in rapid succession.",
+		"exclusion": "Press the configuration button 3 times in rapid succession.",
+		"reset": "Press and hold the configuration button for 20 seconds until LED blinks green rapidly.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4305/Manual_Heatit_ZM_Thermostat%2016A.pdf"
 	}
 }

package/config/devices/0x0208/hkzw_fld01.json

@@ -173,9 +173,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller in add mode (see the controller's manual).\n4) Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast. \n5) Wait for the adding process to end.\n6) Successful adding will be confirmed by the Z-Wave controller's message.",
-		"exclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller remove mode (see the controller's manual).\n4) Triple click the Z-button quickly, the LED indicator should blink fast.\n5) Wait for the removing process to end.\n6) Successful adding will be confirmed by the Z-Wave controller's message.",
-		"reset": "1)Power on the device,\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.\n4) The reset feature works only when the device has been included into a Z-Wave network.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Open the cover\n2. Click the Z-button once or triple click quickly - the LED will blink fast",
+		"exclusion": "1. Open the cover\n2. Triple click the Z-button quickly - the LED will blink fast",
+		"reset": "1. Power on the device\n2. Press and hold the Z-button for more than 20 seconds\n3. The LED will stay on for 2 seconds when reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3895/991557%20flood%20sensor-compressed.pdf"
 	}
 }

package/config/devices/0x0208/hkzw_so03.json

@@ -165,9 +165,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1) Connect the power supply.\n2) Set the Z-Wave network main controller into inclusion mode (see Z-Wave network controller operating manual).\n3) Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue.\n4) Smart Plug should be recognized and included into the Z-Wave network.",
-		"exclusion": "1) Insert the Plug into a socket.\n2) Set the Z-Wave network controller into the exclusion mode (see Z-Wave controller operating manual).\n3) Triple click the Z button.\n4) RGB LED indicator will blink orange till the removing process is completed, than the indicator will keep orange for 3 seconds.",
-		"reset": "1) Insert the Plug into a socket,\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the RGB LED indicator will keep yellow for 2 seconds, which means resetting is complete. \n Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Connect the power supply\n2. Start inclusion\n3. Triple click the Z-button - the RGB LED will blink fast in blue\n4. The smart plug will be included",
+		"exclusion": "1. Insert the plug into a socket\n2. Start exclusion\n3. Triple click the Z-button\n4. The RGB LED will blink orange until complete, then stay orange for 3 seconds",
+		"reset": "1. Insert the plug into a socket\n2. Press and hold the Z-button for more than 20 seconds\n3. The RGB LED will turn yellow for 2 seconds when reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1854/HKZW-SO03_manual.pdf"
 	}
 }

package/config/devices/0x0208/za-216001.json

@@ -183,9 +183,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Connect the power supply.\n2. Set the Z-Wave™ network main controller into learning mode.\n3. Triple click the Z-button, the LED indicator will be flashing 3 times in Blue.\n4. Smart Plug should be recognized and included into the Z-Wave™ network",
-		"exclusion": "1. Insert the Plug into a socket.\n2. Set the Z-Wave™ network controller into the exclusion mode.\n3. Triple click the Z button.\n4. LED will blink in blue for 3 times, and then start slow flashing to indicate that the remove for exclusion is successful. LED will indicate network status after it is removed from Z-Wave™ network",
-		"reset": "Long press the button for 20 seconds and the blue LED will speed up the flash and then LED will keep on for 3 seconds in blue and Smart Plug will send 'Device Reset Locally Notification' to the main controller and exclude from the Z-Wave™ network, this procedure will reset Smart Plug to factory default.",
+		"inclusion": "1. Connect the power supply\n2. Triple click the Z-button - the LED will flash 3 times in blue",
+		"exclusion": "1. Insert the plug into a socket\n2. Triple click the Z-button\n3. The LED will blink blue 3 times, then flash slowly when exclusion is successful",
+		"reset": "Press and hold the button for 20 seconds. The blue LED will flash rapidly then stay on for 3 seconds when reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4196/Manual-SmartPlug.pdf"
 	}
 }

package/config/devices/0x020e/zrksw.json

@@ -52,8 +52,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Turn Off power to the light bulb socket\n2. Screw in the light bulb\n3. Place your network controller into inclusion mode by following the controller manufacturer's instructions\n4. Turn On power to the light bulb. If successful, the LED light bulb will flash twice to indicate successful inclusion.\n5. If the controller/gateway shows it was a fail, repeat the procedure.\n\nNote: If Inclusion still fails after the 2nd attempt, you need to first RESET the dt Smart Bulb before repeating the above steps.",
-		"exclusion": "1. Turn off power to the light bulb socket\n2. Follow the network controller instruction to place your network controller into exclusion mode to remove the dt light bulb from the network.\n3. After being prompted by the network controller, turn On power to the light bulb. If successful, the LED light bulb will flash twice to indicate successful inclusion.",
-		"reset": "You may manually reset the light bulb as follows:\n1. Flick the wall switch 'OFF-ON' 4 times within 4 seconds. \n2. The dt Smart Bulb will flash twice after Reset is successful. \n\nUse this procedure only in the event that the network primary controller is lost or otherwise inoperable"
+		"inclusion": "1. Turn off power to the light bulb socket\n2. Screw in the light bulb\n3. Turn on power to the light bulb\n4. If successful, the LED light bulb will flash twice",
+		"exclusion": "Turn off power to the light bulb socket, then turn on power to the light bulb. If successful, the LED light bulb will flash twice.",
+		"reset": "Flick the wall switch 'OFF-ON' 4 times within 4 seconds. The light bulb will flash twice after reset is successful."
 	}
 }

package/config/devices/0x0217/8001.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To include our device into a controller.\n1.Perform 'Include' on the controller.\n2.From the lock's main menu item '7.Zwave', select the 'ZwaveInclusion' option by using the arrow keys to scroll to it and then pressing ‘M' to select it. After a few seconds, you should see 'Success' on the lock",
-		"exclusion": "To exclude our device from a controller\n1.Perform 'Exclude' on the controller.\n2.From the lock's main menu item '7.Zwave', select the 'ZwaveExclusion' option by using the arrow keys to scroll to it and then pressing ‘M' to select it. After a few seconds, you should see 'Success' on the lock",
-		"reset": "If your controller fails, is replaced or if you need to perform a Factory reset on the device so that an inclusion may be performed again or with a new controller:\nFactory reset can be done on the device by selecting ‘ Hard Reset' from the Main Menu on device's display and pressing the M button. When prompted to reset press the M button on the unit and the device will display initializing. Once the reset is complete the display with return to the Main Menu. \nNote: When a Hard Reset is completed, the zwave node id is initialized to 0 and the device can't be controlled by zwave. In order to control the device again, the controller needs to include the device on zwave network.",
+		"inclusion": "To include our device into a controller.\n1.Perform 'Include' on the controller.\n2.From the lock's main menu item '7.Zwave', select the 'ZwaveInclusion' option by using the arrow keys to scroll to it and then pressing 'M' to select it. After a few seconds, you should see 'Success' on the lock",
+		"exclusion": "To exclude our device from a controller\n1.Perform 'Exclude' on the controller.\n2.From the lock's main menu item '7.Zwave', select the 'ZwaveExclusion' option by using the arrow keys to scroll to it and then pressing 'M' to select it. After a few seconds, you should see 'Success' on the lock",
+		"reset": "If your controller fails, is replaced or if you need to perform a Factory reset on the device so that an inclusion may be performed again or with a new controller:\nFactory reset can be done on the device by selecting ' Hard Reset' from the Main Menu on device's display and pressing the M button. When prompted to reset press the M button on the unit and the device will display initializing. Once the reset is complete the display with return to the Main Menu. \nNote: When a Hard Reset is completed, the zwave node id is initialized to 0 and the device can't be controlled by zwave. In order to control the device again, the controller needs to include the device on zwave network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1511/RTS%20Series%20Operational%20Manual_Updated_Wade_10222015.pdf"
 	}
 }

package/config/devices/0x0217/9001.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "To include our device into a controller.\n1.Perform 'Include' on the controller.\n2.From the lock's main menu item \"7.Zwave\", select the \"ZwaveInclusion\" by using the arrow keys to scroll to it and then pressing 'M' to select it. After a few seconds, you should see \"Success\" on the lock",
 		"exclusion": "To exclude our device from a controller .\n1.Perform 'Exclude' on the controller.\n2.From the lock's main menu item \"7.Zwave\", select the \"ZwaveExclusion\" option by using the arrow keeys to scroll to it and then pressing 'M' to select it. After a few seconds, you should see \"Success\" on the lock",
-		"reset": "If your controller fails or is replaced or if you need to perform a Factory reset on the device so that an inclusion may be performed again or with a new controller, Factory reset can be done on the device by selecting ‘ Hard Reset' from the Main Menu on device's display and pressing the 'M' button. When prompted to reset press the 'M' button on the unit and the device will display initializing. Once the reset is complete the display will return to the Main Menu. \nNote: When a Hard Reset is completed, the zwave node id is initialized to 0 and the device can't be controlled by zwave. In order to control the device again, the controller needs to include the device on zwave network",
+		"reset": "If your controller fails or is replaced or if you need to perform a Factory reset on the device so that an inclusion may be performed again or with a new controller, Factory reset can be done on the device by selecting ' Hard Reset' from the Main Menu on device's display and pressing the 'M' button. When prompted to reset press the 'M' button on the unit and the device will display initializing. Once the reset is complete the display will return to the Main Menu. \nNote: When a Hard Reset is completed, the zwave node id is initialized to 0 and the device can't be controlled by zwave. In order to control the device again, the controller needs to include the device on zwave network",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1342/RTS%20Series%20Operational%20Manual_Updated_10222015.pdf"
 	}
 }

package/config/devices/0x021c/ilock15.json

@@ -14,9 +14,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1）Set gateway in Inclusion.\n2）Set door lock in learn mode. \npress reset button -> input admin password + # -> press 0\n3）Wait until success",
-		"exclusion": "1）Set gateway in exclusion .\n2）Set door lock in learn mode. \npress reset button -> input admin password + # -> press 0\n3）Wait until success",
-		"reset": "User should reset device for safety when receiving lock first or if forget the password or if lost card. The reset way : hold the reset button about 7s, when hear 'Di' sound, then release the button, door lock will be reset. Factory default reset will reset all user (password and card) and home ID and device ID (about Z-Wave function), so be carefully to do reset. The default admin password is 123456 .\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press reset button\n2. Input admin password + #\n3. Press 0",
+		"exclusion": "1. Press reset button\n2. Input admin password + #\n3. Press 0",
+		"reset": "Hold the reset button about 7 seconds until you hear 'Di' sound, then release the button. The default admin password is 123456.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3048/User%20Manual-ilock15.pdf"
 	}
 }

package/config/devices/0x021d/db1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "-Follow the user guide of hub to enter inclusion mode.\n-Operate on lock following guide below:\n1.Enter master mode(refer to programming instruction)\n2.Input '8' to enter 'function extension settings'\n3.Input '1' to join a network",
-		"exclusion": "-Follow the user guide of hub to enter exclusion mode.\n-Operate on lock following guide below:\n1.Enter master mode(refer to programming instruction)\n2.Input '8' to enter 'function extension settings'\n3.Input '2' to log off a network",
-		"reset": "※Please use this procedure only when the network primary controller is missing or inoperable.\n-Operations on lock\n1.Open the door and keep the lock in \"unlock\" status\n2.Open battery box and find the reset button. \n3.Use a sharp thing to press and hold the reset button.\n4.Keep holding the reset button and remove a battery from battery box then replace it.\n5.Keep holding the reset button until hearing voice guide",
+		"inclusion": "1. Enter master mode (refer to programming instructions)\n2. Press '8' to enter function extension settings\n3. Press '1' to join the network",
+		"exclusion": "1. Enter master mode (refer to programming instructions)\n2. Press '8' to enter function extension settings\n3. Press '2' to leave the network",
+		"reset": "1. Open the door and unlock the lock\n2. Open the battery box and locate the reset button\n3. Press and hold the reset button with a pointed object\n4. While holding the reset button, remove a battery, then replace it\n5. Continue holding the reset button until you hear the voice guide",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3373/Alfred%20Z-Wave%20Plus%20System%20Integrators%20Guide(DB1)%20V1.2.pdf"
 	},
 	"compat": {

package/config/devices/0x021d/db2.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "-Follow the user guide of hub to enter inclusion mode.\n-Operate on lock following guide below:\n1.Enter master mode(refer to programming instruction)\n2.Input '8' to enter 'function extension settings'\n3.Input '1' to join a network",
-		"exclusion": "-Follow the user guide of hub to enter exclusion mode.\n-Operate on lock following guide below:\n1.Enter master mode(refer to programming instruction)\n2.Input '8' to enter 'function extension settings'\n3.Input '2' to log off a network",
-		"reset": "※Please use this procedure only when the network primary controller is missing or inoperable.\n-Operations on lock\n1.Open the door and keep the lock in \"unlock\" status\n2.Open battery box and find the reset button. \n3.Use a sharp thing to press and hold the reset button.\n4.Keep holding the reset button and remove a battery from battery box then replace it.\n5.Keep holding the reset button until hearing voice guide",
+		"inclusion": "1. Enter master mode (refer to programming instructions)\n2. Press '8' to enter function extension settings\n3. Press '1' to join the network",
+		"exclusion": "1. Enter master mode (refer to programming instructions)\n2. Press '8' to enter function extension settings\n3. Press '2' to leave the network",
+		"reset": "1. Open the door and unlock the lock\n2. Open the battery box and locate the reset button\n3. Press and hold the reset button with a pointed object\n4. While holding the reset button, remove a battery, then replace it\n5. Continue holding the reset button until you hear the voice guide",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3324/Alfred%20Z-Wave%20Plus%20System%20Integrators%20Guide%20V5.1.pdf"
 	}
 }

package/config/devices/0x021d/ddl240x.json

@@ -110,9 +110,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter master mode(input X + X + Master PIN Code + √)\n2. Input \"0\" to enter \"Network settings\"\n3. Input \"1 + √\" to enter \"Include mode\"",
-		"exclusion": "1. Enter master mode(input X + X + Master PIN Code + √ )\n2. Input \"0\" to enter \"Network settings\"\n3. Input \"2 + √\" to enter \"Exclusion mode\"",
-		"reset": "1. Operations on lock\n1) Remove one of the batteries.\n2) Press and hold the Reset Button.\n3) While pressing, insert the removed battery. When you hear the voice prompt, the factory reset is complete.\n\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter master mode (press X + X + Master PIN Code + √)\n2. Press \"0\" to enter Network settings\n3. Press \"1 + √\" to enter Include mode",
+		"exclusion": "1. Enter master mode (press X + X + Master PIN Code + √)\n2. Press \"0\" to enter Network settings\n3. Press \"2 + √\" to enter Exclusion mode",
+		"reset": "1. Remove one of the batteries\n2. Press and hold the Reset Button\n3. While pressing, insert the removed battery\n4. When you hear the voice prompt, the factory reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/1010/DDL240X-15HZWManualV2.0.pdf"
 	}
 }

package/config/devices/0x021d/hu03.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Join a network: inclusion Z-Wave network and add the lock.\n1.Follow the user guide of hub to enter inclusion mode.\n2.Operate on lock following guide below:\n3.Enter master mode(** + Master PIN Code + #), Wait for 2 Green Lights + 2 Beeps\n4.Input '8+1+#' to enter 'Inclusion mode' (2 Green Lights + 2 Beeps)",
-		"exclusion": "Log off a network: Exclusion Z-Wave network and remove the lock\n1.Follow the user guide of hub to enter exclusion mode.\n2.Operate on lock following guide below:\n3.Enter master mode(** + Master PIN Code + #), Wait for 2 Green Lights + 2 Beeps\n4.Input '8+2+#' to enter 'Exclusion mode'(2 Green Lights + 2 Beeps)",
-		"reset": "Factory reset:\n1.Operations on lock\n2.Open the door and keep the lock in \"unlock\" status\n3.Open battery box and find the reset button. \n4.Use a sharp thing to press and hold the reset button.\n5.Keep holding the reset button for 5 seconds until hearing voice guide",
+		"inclusion": "1. Enter master mode (press ** + Master PIN Code + #)\n2. Wait for 2 green lights and 2 beeps\n3. Press '8+1+#' to enter Inclusion mode\n4. Wait for 2 green lights and 2 beeps",
+		"exclusion": "1. Enter master mode (press ** + Master PIN Code + #)\n2. Wait for 2 green lights and 2 beeps\n3. Press '8+2+#' to enter Exclusion mode\n4. Wait for 2 green lights and 2 beeps",
+		"reset": "1. Open the door and unlock the lock\n2. Open the battery box and locate the reset button\n3. Press and hold the reset button with a pointed object for 5 seconds until you hear the voice guide",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4035/HU04-Product%20Manual%20V1.0.pdf"
 	}
 }

package/config/devices/0x021d/ml2.json

@@ -105,9 +105,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the user guide of hub to enter inclusion mode.\n2. Operate on lock following guide below:\n 1) Enter master mode(** + Master PIN Code + √)\n 2) Input '8' to enter 'function extension settings'\n 3) Input '1' to enter 'Inclusion mode'",
-		"exclusion": "1. Follow the user guide of hub to enter exclusion mode.\n2. Operate on lock following guide below:\n 1) Enter master mode(** + Master PIN Code + √)\n 2) Input '8' to enter 'function extension settings'\n 3) Input '2' to enter 'Exclusion mode'",
-		"reset": "1) Open the door and keep the lock in \"unlock\" status\n 2) Open battery box and find the reset button. \n 3) Use a sharp thing to press and hold the reset button.\n 4) Keep holding the reset button and remove the battery from battery box then replace it.\n 5) Keep holding the reset button down until you hear the lock beep (Can take up to 10 seconds).\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Enter master mode (press ** + Master PIN Code + √)\n2. Press '8' to enter function extension settings\n3. Press '1' to enter Inclusion mode",
+		"exclusion": "1. Enter master mode (press ** + Master PIN Code + √)\n2. Press '8' to enter function extension settings\n3. Press '2' to enter Exclusion mode",
+		"reset": "1. Open the door and unlock the lock\n2. Open the battery box and locate the reset button\n3. Press and hold the reset button with a pointed object\n4. While holding the reset button, remove a battery, then replace it\n5. Continue holding the reset button until you hear the lock beep (can take up to 10 seconds)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4120/ML2%20-%20Product%20Manual_new.pdf"
 	}
 }

package/config/devices/0x021f/dmex1.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, press the Z-Wave Button on Range Extender 3 times",
-		"exclusion": "Turn the primary controller of the Z-Wave network into exclusion mode, press the Z-Wave Button on Range Extender 3 times",
-		"reset": "Press and hold the Z-Wave Button for 10 seconds and then release it.\nUse this procedure only in the event that your primary network controller is missing or inoperable",
+		"inclusion": "Press the Z-Wave button on the range extender 3 times.",
+		"exclusion": "Press the Z-Wave button on the range extender 3 times.",
+		"reset": "Press and hold the Z-Wave button for 10 seconds and then release it.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2984/DomeExtenderAPIManual10-31.pdf"
 	}
 }