@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x0063/35530_zw6302B.json

@@ -46,9 +46,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add the device in the Z-Wave network.\n2. Once the controller is ready to add your\nmotion sensor, press and release the button\non the sensor to add it in the network.\n3. The blue LED will activate for 3 seconds to\nconfirm it has been included in the network",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove the device from the Z-Wave network.\n2. Once the controller is ready to remove your\nmotion sensor, press and release the button on\nthe sensor to exclude it from the network.\n3. The LED will blink for 3 seconds at a time.\n\nNOTE: If the sensor's power source is changed\nafter initial setup (ex: USB power instead of\nbattery power), the sensor must be excluded\nfrom the network and then re-included",
-		"reset": "1. Press the button 10 times within 6 seconds\n(interval between 2 presses of the button\ncannot be longer than 1 second).\n2. The blue LED will blink for 3 seconds",
+		"inclusion": "Press and release the button on the sensor. The blue LED will activate for 3 seconds to confirm inclusion.",
+		"exclusion": "Press and release the button on the sensor. The LED will blink for 3 seconds at a time.",
+		"reset": "1. Press the button 10 times within 6 seconds (interval between presses cannot be longer than 1 second).\n2. The blue LED will blink for 3 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2157/35530%20QSG%20and%20Parameters.pdf"
 	}
 }

package/config/devices/0x0063/37792_zw5307.json

@@ -21,7 +21,7 @@
 		}
 	],
 	"metadata": {
-		"reset": "Returning your remote to factory defaults\n1. Press and release Button 1 ten times quickly. All button presses must be within 6 seconds.\n2. The LED will flash five (5) times when completed successfully.\nNOTE: This should only be used in the event your network's primary controller/hub is missing or otherwise inoperable",
+		"reset": "1. Press and release Button 1 ten times quickly within 6 seconds.\n2. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2930/37792%20QSG%20w%20Parameters.pdf"
 	}
 }

package/config/devices/0x0063/38957_zw6305.json

@@ -109,9 +109,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has been removed.\n3. Press and release the programming button. This starts the manual add process. The red LED will begin to flash quickly as it begins the add process.\n4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n5. The controller's app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button on the sensor 1 time to remove it from the network.\n3. The red LED will blink 5 times to indicate it has been removed.",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes.\n\n- Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Press and release the programming button. The red LED will begin to flash quickly.\n2. The red LED will activate for 3 seconds to confirm inclusion.",
+		"exclusion": "Press and release the programming button. The red LED will blink 5 times to indicate removal.",
+		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3115/38957-QSG-1.pdf"
 	}
 }

package/config/devices/0x0063/38959_zw6306.json

@@ -144,9 +144,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n\n2. Once the controller is ready to add your device, remove the top cover of the sensor. Ensure battery is installed with the correct polarity and the battery tab has been removed, or ensure micro USB is plugged into USB port.\n\n3. Press and release the programming button (see figure 10). This starts the manual add process. The red LED flashes quickly as it searches for a network. After 25 seconds, the LED will stop flashing. Press the programming button to manually start the add process. If it times out, the LED will stop flashing. Press and release the programming button again.\n\n4. The controller's app will indicate if it discovers the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product (see above). Enter the 5-digit code.\n\n5. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n\n6. Secure the top cover into place",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n\n2. Once the controller is ready to remove your sensor, press and release the programming button one time on the sensor (see figure 10).\n\n3. The red LED will blink five times to indicate it has been removed. Secure the top cover",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be longer than 1 second).\n\n2. The red LED will activate for 2 seconds, followed by three quick flashes. This confirms the sensor has been reset. Secure the top cover into place.\n\nNote: This should only be used if your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Remove the top cover.\n2. Press and release the programming button. The red LED flashes quickly as it searches.\n3. If the LED stops flashing after 25 seconds, press the programming button again to manually restart the process.\n4. The red LED will activate for 3 seconds to confirm inclusion.\n5. Secure the top cover into place.",
+		"exclusion": "1. Press and release the programming button one time.\n2. The red LED will blink five times to indicate removal.\n3. Secure the top cover.",
+		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by three quick flashes.\n3. Secure the top cover into place.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3642/38959%20EnFrSp%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/39348_54890_54891_zw4008.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the smart switch rocker)",
-		"reset": "Quickly press ON (top) button three times, then, immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully",
+		"inclusion": "Press and release the top or bottom of the smart switch rocker.",
+		"exclusion": "Press and release the top or bottom of the smart switch rocker.",
+		"reset": "Quickly press top button three times, then immediately press the bottom button three times. The LED will flash ON/OFF five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4168/39348%20QSG%20v3.pdf"
 	}
 }

package/config/devices/0x0063/39351_zw3010.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the smart dimmer (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the smart dimmer (rocker)",
-		"reset": "Quickly press ON (top) button three times, then, immediately press the OFF (Bottom) button three times. The LED will flash ON/OFF five times when completed successfully.",
+		"inclusion": "Press and release the top or bottom of the smart dimmer rocker.",
+		"exclusion": "Press and release the top or bottom of the smart dimmer rocker.",
+		"reset": "Quickly press the top of the rocker three times, then immediately press the bottom of the rocker three times. The LED will flash ON/OFF five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4031/39351%20QSG%20v4.pdf"
 	}
 }

package/config/devices/0x0063/39354_54912_zw4009.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up on the toggle",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up on the toggle",
-		"reset": "Quickly press up three times, then, immediately press down three times",
+		"inclusion": "Press up on the toggle.",
+		"exclusion": "Press up on the toggle.",
+		"reset": "Quickly press up three times, then immediately press down three times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4171/39354%20QSG%20v3.pdf"
 	}
 }

package/config/devices/0x0063/43072_zw4008dv.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart switch (rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately press the OFF (Bottom) button three times. The LED will flash ON/OFF five times when completed successfully. Note: This should only be used if your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the switch.",
+		"exclusion": "Press and release the top or bottom of the switch.",
+		"reset": "1. Quickly press top button three times.\n2. Immediately press the bottom button three times.\n3. The LED will flash ON/OFF five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4156/43072%20QSG%20v4.pdf"
 	}
 }

package/config/devices/0x0063/43074_zw4009dv.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart switch (rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately press the OFF (Bottom) button three times. The LED will flash ON/OFF five times when completed successfully. Note: This should only be used if your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the switch.",
+		"exclusion": "Press and release the top or bottom of the switch.",
+		"reset": "1. Quickly press ON (top) button three times.\n2. Immediately press the OFF (bottom) button three times.\n\nThe LED will flash ON/OFF five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4167/43074%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/43105_zw3010dv.json

@@ -60,9 +60,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up and release the top or bottom of the rocker.\n3. The controller's app will indicate if it has discovered the switch. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up and release the toggle",
-		"reset": "Quickly press ON (up) button three times then immediately press the OFF (down) button three times",
+		"inclusion": "Press and release the top or bottom of the rocker.",
+		"exclusion": "Press and release the toggle.",
+		"reset": "1. Quickly press top button three times.\n2. Immediately press the bottom button three times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4162/43105%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/43107_zw3011dv.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up and release the toggle.\n3. The controller's app will indicate if it discovers the switch. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up and release the toggle",
-		"reset": "Quickly press ON (up) button three times then immediately press the OFF (down) button three times.",
+		"inclusion": "Press and release the toggle.",
+		"exclusion": "Press and release the toggle.",
+		"reset": "1. Quickly press top button three times.\n2. Immediately press the bottom button three times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4163/43107%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/43973_zw6305.json

@@ -109,9 +109,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Automatic mode\n1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your sensor, slide the battery door down and remove (if not mounted to door or window).\n3. Remove the plastic battery tab. This activates the sensor and starts the auto-add process. The red LED will begin to flash\nquickly as it searches for a network. The sensor will attempt to search for a network for two minutes, after which, it will time out.\n4. The red LED will continue to flash quickly after it locates a network – the controller's app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code.\n5. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n\nManual mode\n1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has been removed.\n3. Press and release the programming button. This starts the manual add process. The red LED will begin to flash quickly as it begins the add process.\n4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n5. The controller's app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button on the sensor 1 time to remove it from the network.\n3. The red LED will blink 5 times to indicate it has been removed",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes.\n\n- Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press and release the programming button.\n2. The red LED will flash quickly during the process.\n3. It will activate for 3 seconds when successful.",
+		"exclusion": "Press and release the programming button. The red LED will blink 5 times to indicate removal.",
+		"reset": "1. Press the programming button 10 times within 6 seconds.\n2. The interval between presses cannot be longer than 1 second.\n3. The red LED will activate for 2 seconds, followed by 3 quick flashes.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3188/43973%20EnFrSp%20QSG%20v1%20with%20Parameters%20(2).pdf"
 	}
 }

package/config/devices/0x0063/43985_zw6306.json

@@ -145,9 +145,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your device, remove the top cover of the sensor. Ensure battery is installed with the correct polarity and the battery tab has been removed, or ensure micro USB is plugged into USB port.\n3. Press and release the programming button (see figure 10). This starts the manual add process. The red LED flashes quickly as it searches for a network. After 25 seconds, the LED will stop flashing. Press the programming button to manually start the add process. If it times out, the LED will stop flashing. Press and release the programming button again.\n4. The controller's app will indicate if it discovers the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product (see above). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button one time on the sensor (see figure 10).\n3. The red LED will blink five times to indicate it has been removed. Secure the top cover",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by three quick flashes. This confirms the sensor has been reset. Secure the top cover into place.\nNote: This should only be used if your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Remove the top cover of the sensor.\n2. Press and release the programming button.\n3. The red LED flashes quickly during the process.",
+		"exclusion": "Press and release the programming button. The red LED will blink five times to indicate removal.",
+		"reset": "1. Press the programming button 10 times within 6 seconds.\n2. The interval between presses cannot be longer than 1 second.\n3. The red LED will activate for 2 seconds, followed by three quick flashes.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3678/43985%20EnFrSp%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/45743_zw4002.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, press and release the top or bottom of the smart fan control switch (rocker) to include it in the network.\n3. Once your controller has confirmed the device has been included, refresh the Z-Wave network to optimize performance",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network. \n2. Once the controller is ready to Exclude your device, press and release the top or bottom of the wireless smart switch (rocker) to exclude it from the network",
-		"reset": "1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the fan control switch.",
+		"exclusion": "Press and release the top or bottom of the fan control switch.",
+		"reset": "1. Quickly press the top button three times then immediately press the bottom button three times. 2. The LED will flash on/off 5 times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2557/Binder2.pdf"
 	}
 }

package/config/devices/0x0063/46201_zw4008.json

@@ -45,9 +45,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately\npress the OFF (Bottom) button three times. The LED will\nflash ON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"reset": "Quickly press the top button three times then immediately press the bottom button three times. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4143/46201%20QSG%20v4.pdf"
 	}
 }

package/config/devices/0x0063/46202_zw4009.json

@@ -48,9 +48,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up and release the toggle.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up and release the toggle.",
-		"reset": "Quickly press ON (up) button three times, then immediately press the OFF (down) button three times.",
+		"inclusion": "Press up and release the toggle.",
+		"exclusion": "Press up and release the toggle.",
+		"reset": "Quickly press the up button three times then immediately press the down button three times. The LED will flash when completed successfully.",
 		"manual": "https://byjasco.com/media/manuals/46202-QSG-v1.pdf"
 	}
 }

package/config/devices/0x0063/46203_zw3010.json

@@ -68,9 +68,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart dimmer (rocker) to add it in the network.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart dimmer (rocker) to remove it from the network",
-		"reset": "Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"reset": "Quickly press the top button 3 times then immediately press the bottom button 3 times. The LED will flash 5 times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4024/46203%20QSG%20v3%20(3).pdf"
 	}
 }

package/config/devices/0x0063/46204_zw3011.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release\nthe top or bottom of the wireless smart dimmer (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the top or bottom of the wireless smart dimmer (rocker)",
-		"reset": "1. Quickly press ON (top) button three times, then immediately\npress the OFF (Bottom) button three times. The LED will\nflash ON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"reset": "Quickly press the top button three times then immediately press the bottom button three times. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3352/14295.46204%20Binder.pdf"
 	}
 }

package/config/devices/0x0063/46562_zw4008.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately\npress the OFF (Bottom) button three times. The LED will\nflash ON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"reset": "Quickly press the top button three times then immediately press the bottom button three times. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4142/46562%20EnFrSp%20QSG%20v3.pdf"
 	}
 }

package/config/devices/0x0063/46563_zw4009.json

@@ -44,9 +44,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the top or bottom of the wireless smart switch (rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately\npress the OFF (Bottom) button three times. The LED will\nflash ON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart switch (rocker).",
+		"reset": "Quickly press the top button three times then immediately press the bottom button three times. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3359/14319.46563%20Binder.pdf"
 	}
 }

package/config/devices/0x0063/46565_zw3011.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release\nthe top or bottom of the wireless smart dimmer (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the top or bottom of the wireless smart dimmer (rocker)",
-		"reset": "1. Quickly press ON (top) button three times, then immediately\npress the OFF (Bottom) button three times. The LED will\nflash ON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"reset": "Quickly press the top button three times then immediately press the bottom button three times. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3360/14322.46565%20Binder1.pdf"
 	}
 }

package/config/devices/0x0063/52190_zw7105.json

@@ -36,9 +36,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Adding your device to a Z-Wave network\n1. When initially powered, the bulb is in SmartStart inclusion mode. If your hub supports SmartStart, scan the\nQR code.\n2. To change to classic inclusion mode, turn bulb OFF, then ON three times. The bulb rapidly flashes four\ntimes to indicate classic mode.\n3. To change back to SmartStart inclusion mode, turn the bulb OFF, then ON three times. The bulb rapidly\nflashes six times to indicate SmartStart mode.\nNOTE: The bulb attempts to connect in either inclusion mode for 10 seconds. If not found after 10 seconds,\ncycle the bulb OFF/ON to restart the inclusion mode.\n4. In either method, the bulb flashes twice to indicate it was added to the network.\nNOTE: The bulb remains in the last known inclusion mode when cycled OFF/ON once.\nYou have complete control to turn your light ON/OFF or set dim levels according to groups, scenes, schedules\nand interactive automations programmed by your controller.\nIf your Z-Wave certified controller features remote access, you can control your lighting from your mobile\ndevices.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side\nof the box or the QR code label on the product (see Figure 1). Enter the 5-digit pin code.\nFigure 1.\nNOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the\nproduct with a controller providing SmartStart inclusion. No further action is required and the SmartStart\nproduct will be added automatically within 10 minutes of being switched on in the network vicinity",
-		"exclusion": "To remove and reset the device\n1. Follow the instructions for your Z-Wave certified controller\nto remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, turn\nbulb OFF, then ON three times. The smart bulb flashes\ntwice when removed from the network",
-		"reset": "To return your smart bulb to factory defaults\nStarting with the bulb on, cycle the wall switch OFF/ON\nfour times.\n1. Turn the switch off, pause one second, then turn back ON.\n2. Repeat three times (four times total).\n3. The smart bulb flashes twice when reset.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable",
+		"inclusion": "1. Turn bulb OFF, then ON three times. The bulb rapidly flashes four times to indicate classic mode.\n2. The bulb flashes twice to confirm inclusion.",
+		"exclusion": "Turn bulb OFF, then ON three times. The bulb flashes twice when removed.",
+		"reset": "1. Starting with the bulb on, turn the switch off, pause one second, then turn back ON.\n2. Repeat three times (four times total).\n3. The bulb flashes twice when reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4145/52190-2.pdf"
 	}
 }

package/config/devices/0x0063/52247_zw6309.json

@@ -145,9 +145,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Battery power/micro USB power\n1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your device, remove the top cover of the sensor (see figure 7).\n3. Ensure battery is installed with the correct polarity and the battery tab has been removed (see figure 8) or ensure micro USB is plugged into USB port (see figure 9).\n4. Press and release the programming button (see figure 10). This starts the manual add process. The red LED flashes quickly as it searches for a network. After 25 seconds, the LED will stop flashing if the sensor is not\nadded to the network. Press the programming button to manually start the add process. If it times out, the LED will stop flashing. Press and release the programming button again.\n5. The controller's app will indicate if it discovers the sensor.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button one time on the sensor (see figure 10).\n3. The red LED will blink five times to indicate it has been removed. Secure the top cover",
-		"reset": "1. Press the programming button 10 times within six seconds (interval between presses of the button cannot be longer than one second).\n2. The red LED will activate for two seconds, followed by three quick flashes to confirm the sensor has been reset. Secure the top cover into place.\nNote: This should only be used if your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Remove the top cover.\n2. Ensure battery is installed with correct polarity and the battery tab has been removed, or ensure micro USB is plugged in.\n3. Press and release the programming button. The red LED flashes quickly.\n4. After 25 seconds, the LED will stop flashing if the sensor is not added. Press the programming button again to restart the process.",
+		"exclusion": "1. Press and release the programming button one time.\n2. The red LED will blink five times to indicate it has been removed.\n3. Secure the top cover.",
+		"reset": "1. Press the programming button 10 times within six seconds (interval between presses cannot be longer than one second).\n2. The red LED will activate for two seconds, followed by three quick flashes to confirm the sensor has been reset.\n3. Secure the top cover into place.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3953/52247_QSG_v1[1].pdf"
 	}
 }

package/config/devices/0x0063/52249_zw6308.json

@@ -106,9 +106,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has been removed.\n3. Press and release the programming button (see Figure 2). This starts the manual add process. The red LED (see Figure 2) will begin to flash quickly as it begins the add process.\n4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n5. The controller's app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product (see Figure 3). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button on the sensor\n1 time to remove it from the network (see Figure 4).\n3. The red LED will blink 5 times to indicate it has been removed",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be\nlonger than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes.",
+		"inclusion": "1. Ensure battery is installed with correct polarity and the battery tab has been removed.\n2. Press and release the programming button. The red LED will begin to flash quickly.\n3. The red LED will activate for 3 seconds to confirm inclusion.",
+		"exclusion": "1. Press and release the programming button one time.\n2. The red LED will blink 5 times to indicate it has been removed.",
+		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses cannot be longer than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3955/52249_QSG_v1[1].pdf"
 	}
 }

package/config/devices/0x0063/52251_zw6307.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the device in the Z-Wave network.\n2. Once the controller is ready to add your motion sensor, press and release the button on the sensor.\n3. The blue LED will continue to flash quickly after it locates a network – the controller's app will indicate if it discovers the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product (see figure 3). Enter the 5-digit code.\n4. The blue LED will activate for 3 seconds to confirm it has been added in the network.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove the device from the Z-Wave network.\n2. Once the controller is ready to remove your motion sensor, press and release the button on the sensor.\n3. The LED will blink 5 times",
-		"reset": "1. Press the button 10 times within 6 seconds (interval between 2 presses of the button cannot be longer than 1 second).\n2. The blue LED will blink 3 times",
+		"inclusion": "1. Press and release the button on the sensor.\n2. The blue LED will continue to flash quickly.\n3. The blue LED will activate for 3 seconds to confirm inclusion.",
+		"exclusion": "1. Press and release the button on the sensor.\n2. The LED will blink 5 times.",
+		"reset": "1. Press the button 10 times within 6 seconds (interval between presses cannot be longer than 1 second).\n2. The blue LED will blink 3 times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3971/52251_QSG_v1[1].pdf"
 	}
 }

package/config/devices/0x0063/52252_zw3012.json

@@ -72,9 +72,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the smart dimmer (rocker)",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the smart dimmer (rocker)",
-		"reset": "1. Quickly press ON (top) button three times, then immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully",
+		"inclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"exclusion": "Press and release the top or bottom of the smart dimmer (rocker).",
+		"reset": "1. Quickly press the top button three times.\n2. Immediately press the bottom button three times.\n3. The LED will flash ON/OFF five times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3987/52252_QSG_v1[1].pdf"
 	}
 }

package/config/devices/0x0063/53829_zw5313.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.\n2. Once the hub is ready to add your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends add notification (NIF).\n4. The LED will keep lighting up for one minute if inclusion is successful.5. Following the instructions for your Z-Wave certified hub, assign actions for each button press. An action can be many combinations of scenes, groups\nor events, and is greatly dependent on the hub capabilities.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified hub to remove a device from the Z-Wave network.\n2. Once the hub is ready to remove your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends remove notification (NIF)",
-		"reset": "1. Press and release Button 1 ten times quickly. All button presses must be within 6 seconds.\n2. The LED will flash five (5) times when completed successfully.",
+		"inclusion": "1. Press and hold either button for three seconds.\n2. The LED will flash two times when the remote sends add notification.\n3. The LED will keep lighting up for one minute to confirm inclusion.",
+		"exclusion": "1. Press and hold either button for three seconds.\n2. The LED will flash two times when the remote sends remove notification.",
+		"reset": "1. Press and release Button 1 ten times quickly. All button presses must be within 6 seconds.\n2. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3958/53829-QSG-v1[2].pdf"
 	}
 }

package/config/devices/0x0063/53831_zw5314.json

@@ -40,8 +40,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.\n2. Once the hub is ready to add your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends add notification (NIF).\n4. The LED will keep lighting up for one minute if inclusion is successful.\n5. Following the instructions for your Z-Wave certified hub, assign actions for each button press. An action can be many combinations of scenes, groups or events, and is greatly dependent on the hub capabilities.",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified hub to remove a device from the Z-Wave network.\n2. Once the hub is ready to remove your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends remove notification (NIF)",
+		"inclusion": "1. Press and hold either button for three seconds.\n2. The LED will flash two times when the remote sends add notification.\n3. The LED will keep lighting up for one minute to confirm inclusion.",
+		"exclusion": "1. Press and hold either button for three seconds.\n2. The LED will flash two times when the remote sends remove notification.",
 		"reset": "1. Press and release button 1 10 times quickly. All button presses must be within six seconds.\n2. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3959/53831-QSG-v1%20(3).pdf"
 	}

package/config/devices/0x0063/55249_zw4106.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.\n2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has\nbeen removed.\n3. Press and release the programming button (see Figure 2). This starts the manual add process. The red LED (see Figure 2) will begin to\nflash quickly as it begins the add process.\n4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.\n5. The controller's app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR\ncode/security number on the back of the box, or the QR code label on the product (see Figure 3). Enter the 5-digit code.\nNote: Your controller may need to be within 10ft. of the sensor to be added.\nUsing the controller, you can activate interactive automations when the sensor detects when a door or window is opened or closed.\nFunctions may vary depending on gateway or controller",
-		"exclusion": "To remove the sensor from the Z-Wave network\n1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.\n2. Once the controller is ready to remove your sensor, press and release the programming button on the sensor\n1 time to remove it from the network (see Figure 4).\n3. The red LED will blink 5 times to indicate it has been removed",
-		"reset": "1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be\nlonger than 1 second).\n2. The red LED will activate for 2 seconds, followed by 3 quick flashes",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. If plugged in, unplug the switch from the receptacle. 2. Press and hold the program button for at least three seconds while you plug the switch into a receptacle.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3915/55249%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/55250_zw4104.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add the smart switch to the Z-Wave network.\n2. Once the controller is ready to add your smart switch, press and release the manual/program button on the smart switch",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a smart switch from the Z-Wave network.\n2. Once the controller is ready to remove your smart switch, press and release the manual/program button on the smart switch",
-		"reset": "1. If plugged in, unplug the smart switch from the receptacle.\n2. Press and hold the program button for at least three seconds while you plug the smart switch into a receptacle",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. If plugged in, unplug the smart switch from the receptacle. 2. Press and hold the program button for at least three seconds while you plug the smart switch into a receptacle.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3936/55250%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/55251_zw3107.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your smart dimmer, single press and release the manual/program button on\nthe smart dimmer",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave\nnetwork.\n2. Once the controller is ready to remove your device, press and release the manual/program button on the smart dimmer",
-		"reset": "1. If plugged in, unplug the dimmer from the receptacle.\n2. Press and hold the top button for at least three seconds while you plug the dimmer into a receptacle.\n3. The LED will flash five times when completed successfully",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. If plugged in, unplug the dimmer from the receptacle. 2. Press and hold the top button for at least three seconds while you plug the dimmer into a receptacle. 3. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3974/55251%20QSG%20v1%20(1).pdf"
 	}
 }

package/config/devices/0x0063/55252_zw3105.json

@@ -64,9 +64,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press the program button of the smart dimmer",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave\nnetwork.\n2. Once the controller is ready to remove your device, press and release the manual/program button on the smart dimmer",
-		"reset": "1. If plugged in, unplug the dimmer from the receptacle.\n2. Press and hold the top button for at least there seconds while you plug the dimmer into a receptacle",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. If plugged in, unplug the dimmer from the receptacle. 2. Press and hold the top button for at least three seconds while you plug the dimmer into a receptacle.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3934/55252%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/55256_zw1002.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network. 2. Once the controller is ready to add your device, press and release the program button",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device to the Z-Wave network. 2. Once the controller is ready to add your device, press and release the manual/program button",
-		"reset": "Press the button three times, then press and hold the button for at least three seconds. The LED will blink five times to confirm",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "Press the button three times, then press and hold the button for at least three seconds. The LED will blink five times to confirm.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3892/55256_QSG_v1[1].pdf"
 	}
 }

package/config/devices/0x0063/55257_zw1002.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the program button",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device to the Z-Wave network. \n2. Once the controller is ready to add your device, press and release the manual/program button",
-		"reset": "Press the button three times, then press and hold the button for at least three seconds. The LED will blink five times to confirm",
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "Press the button three times, then press and hold the button for at least three seconds. The LED will blink five times to confirm.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3978/55257%20QSG%20v1%20(1).pdf"
 	}
 }

package/config/devices/0x0063/55258_zw4002.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom rocker",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom rocker",
-		"reset": "Quickly press ON (top) button three times, then immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully",
+		"inclusion": "Press and release the top or bottom rocker.",
+		"exclusion": "Press and release the top or bottom rocker.",
+		"reset": "1. Quickly press the top button three times, then immediately press the bottom button three times. 2. The LED will flash on/off five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3928/55258%20QSG%20v1%20(5).pdf"
 	}
 }

package/config/devices/0x0063/55259_zw4002.json

@@ -40,9 +40,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom rocker",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom rocker",
-		"reset": "Quickly press ON (top) button three times, then immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully",
+		"inclusion": "Press and release the top or bottom rocker.",
+		"exclusion": "Press and release the top or bottom rocker.",
+		"reset": "1. Quickly press the top button three times, then immediately press the bottom button three times. 2. The LED will flash on/off five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3979/55259%20QSG%20v1%20(1).pdf"
 	}
 }