@zwave-js/config 15.7.0 → 15.8.0

package/config/devices/0x042a/zd2105us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2105 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2105 then the device will send a signal to be included (or excluded) to/from the network; otherwise, ZD2105 will go to sleep after 20 seconds",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZD2105 from your controller. Press the program switch of ZD2105 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2105 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch of ZD2105.",
+		"exclusion": "Press the program switch of ZD2105 for 1 second.",
+		"reset": "1. Trigger the rear cover switch to send the Alarm Report\n2. Trigger the reed switch (close & open) 5 times in 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3583/ZD2105-5%20GCS.pdf"
 	}
 }

package/config/devices/0x042c/wmbr.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)\n2. Select the About page\n3. Select ‘Advanced Z-Wave Utilities'\n4. Select ‘Add device'\n5. Refer to the manufacturer's instruction for inclusion using the DSK (device specific key). A user may attempt to use classic inclusion by entering `00000` as the DSK.\n6. The app will indicate when device inclusion is successful",
-		"exclusion": "EXCLUSION\n1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)\n2. Select the About page\n3. Select ‘Advanced Z-Wave Utilities'\n4. Select ‘Exclude garage opener' to put the bridge in Exclusion Mode. Refer to the manufacturer's instruction for exclusion.\n5. The app will indicate when device exclusion is successful.",
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nTo factory reset the WiFi Bridge, which will also factory reset and delete all Z-Wave network information, press and hold the button on the back of the bridge for 20 seconds",
+		"inclusion": "1. Navigate to the Settings page by pressing the gear icon\n2. Select the About page\n3. Select 'Advanced Z-Wave Utilities'\n4. Select 'Add device'\n5. Enter 00000 as the DSK for classic inclusion",
+		"exclusion": "1. Navigate to the Settings page by pressing the gear icon\n2. Select the About page\n3. Select 'Advanced Z-Wave Utilities'\n4. Select 'Exclude garage opener'\n5. Refer to the manufacturer's instruction for exclusion",
+		"reset": "Press and hold the button on the back of the bridge for 20 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3673/Updated%20User%20Manual%209.20.pdf"
 	}
 }

package/config/devices/0x042f/connect2.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Start inclusion, per instructions on the existing network controller.\nIn the UI, press the learn button.\nWhen prompted, enter the 5 digit underlined portion of the DSK code.\nVerify secure inclusion completed successfully on the existing network controller per that documentation",
-		"exclusion": "Start exclusion, per instructions on the existing network controller.\nIn the UI, press the learn button.\nVerify exclusion completed successfully on the existing network controller per that documentation",
+		"inclusion": "In the UI, press the learn button. When prompted, enter the 5 digit underlined portion of the DSK code.",
+		"exclusion": "In the UI, press the learn button.",
 		"reset": "In the UI, press Hard Reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3441/IOTAS%20Consumer%20Hub%20Manual.pdf"
 	}

package/config/devices/0x043d/pgd728f_zpu.json

@@ -33,8 +33,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Bring the DoorLock within direct range of your controller.\n2. Carefully remove the battery compartment cover. \n3. Put your Z-Wave controller into inclusion mode. \n4. Simply press the Program button to enter programming mode.\n5. Select '2HB' to enter hub action menu.\n6. Select 'AD' and wait doorlock to finish the inclusion",
-		"exclusion": "1. Make sure the DoorLock is powered on and located within direct\n range of your Z-Wave gateway controller .\n2. Put your Z-Wave controller into exclusion mode .\n3. Simply press the Program button to enter programming mode.\n4. Select '2HB' to enter hub action menu.\n5. Select 'DE' and wait doorlock to finish the exclusion",
-		"reset": "When your network's primary controller is missing or otherwise \ninoperable, you may need to reset the device to factory settings \nmanually. Tocomplete \nthe process, make sure your doorlock has not been synced tothe \nsmart phone, then press and hold the reset button at least 3 sec to \nreset the doorlock and Z-Wave module. Also, you can restore the \nlock to factory default settings while the lock is synching with the \nsmartphone.\nWhen executing factory reset, Z-Wave module will issue the following \ninstructions to smart home controller.\nGroup：\"LIFELINE\" group\nInstruction: DEVICE_RESET_LOCALLY_NOTIFICATION"
+		"inclusion": "1. Remove the battery compartment cover\n2. Press the Program button to enter programming mode\n3. Select '2HB' to enter hub action menu\n4. Select 'AD' and wait for inclusion to complete",
+		"exclusion": "1. Press the Program button to enter programming mode\n2. Select '2HB' to enter hub action menu\n3. Select 'DE' and wait for exclusion to complete",
+		"reset": "Press and hold the reset button for at least 3 seconds. Make sure the doorlock is not synced to a smartphone before resetting."
 	}
 }

package/config/devices/0x0447/sqr62101whz.json

@@ -21,9 +21,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "A. SmartStart inclusion: The feature assumes the gateway has implemented SmartStart. Users could use the APP of the gateway or the gateway camera to scan the QR code on device or on device package before powering on the device, and then when the device is powered on, it shall be automatically added to the gateway.\nB. Manual inclusion: When the gateway is in adding mode (please refer to the instruction of the Z-Wave gateway for the operations on gateway itself), press the program button 3 times within 1.5s (the interval between each press is less than 0.5s)",
-		"exclusion": "Exclusion from a Z-Wave network: When the gateway is in removing mode (please refer to the instruction of the Z-Wave gateway for the operations on gateway itself), press the program button 3 times within 1.5s (the interval between each press is less than 0.5s)",
-		"reset": "3x quick click +1 x press> 10 seconds",
+		"inclusion": "Press the program button 3 times within 1.5s (the interval between each press is less than 0.5s).",
+		"exclusion": "Press the program button 3 times within 1.5s (the interval between each press is less than 0.5s).",
+		"reset": "1. Press the program button 3 times quickly\n2. Press and hold the program button for more than 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3922/GDE77980%20Z-Wave%20plug%20user%20manual_English%20version.pdf"
 	}
 }

package/config/devices/0x044b/wp-02sf.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Add：It will trigger ADD/REMOVE after press the OPEN button for more than 5seconds. Try again if failed. Notice: The triggering will be activated after the PRESS stopped",
-		"exclusion": "B. Remove：It will trigger ADD/REMOVE after press the OPEN button for more than 5 seconds. Try again if failed. Notice: The triggering will be activated after the PRESS stopped",
-		"reset": "Support Device Locally Reset\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the OPEN button for more than 5 seconds then release.",
+		"exclusion": "Press the OPEN button for more than 5 seconds then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4027/WP-02SF%20202011.pdf"
 	}
 }

package/config/devices/0x044c/myot.json

@@ -68,8 +68,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds",
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
 		"manual": "https://www.myvirtuosohome.com/en/downloads/send/4-manuals/209-z-wave-interface-actuator-manual-opentherm-boilers.html"
 	}
 }

package/config/devices/0x044c/myot2.json

@@ -195,7 +195,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds"
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds."
 	}
 }

package/config/devices/0x044c/myot4.json

@@ -116,7 +116,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds"
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds."
 	}
 }

package/config/devices/0x044f/uvh1301.json

@@ -22,9 +22,6 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Select \"Join Network\" in the app to put the kitchen hub into learn mode to join another network",
-		"exclusion": "Same as Inclusion",
-		"reset": "Factory Reset is available through the Settings menu in the app",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4285/zwave%20manual%20fixed.pdf"
 	}
 }

package/config/devices/0x045a/WB04V.json

@@ -341,8 +341,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/config/devices/0x045a/WM25L.json

@@ -238,8 +238,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote:Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/config/devices/0x045a/Z-TRV-V01.json

@@ -152,8 +152,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power on your TRV. \n2. Set your Z-Wave controller into add/inclusion mode.\n3. In 'OF' state, short press rotary plate three times unit this screen shows '--'.\n4. The screen will show 'PA' after few seconds, whick meant the inclusion is successful. And the signal icon will light on. Otherwise, the inclusion is failed, which you will need to repeat the process.",
-		"exclusion": "1. Power on your TRV. \n2. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n3. In 'OF' state, short press rotary plate three times unit this screen shows '--'.\n4. The screen will turn back to 'OF' after few seconds. which meant the exclusion is successful. The signal light turn off.",
-		"reset": "Use this procedure only in the event that the primary controller is lost or otherwise inoperable. \n1. In 'OF' state, hold rotary plate for at least 5 seconds and release when screen will blink 'OF'. When successful, the screen will show 'OF' in solid for 2 seconds then turn off."
+		"inclusion": "1. Power on the TRV\n2. When the display shows 'OF', quickly press the rotary plate three times until the screen shows '--'\n3. The screen will show 'PA' if inclusion is successful",
+		"exclusion": "1. Power on the TRV\n2. When the display shows 'OF', quickly press the rotary plate three times until the screen shows '--'\n3. The screen will return to 'OF' if exclusion is successful",
+		"reset": "When the display shows 'OF', press and hold the rotary plate for at least 5 seconds until the screen blinks 'OF'"
 	}
 }

package/config/devices/0x0460/qldm-0A101.json

@@ -0,0 +1,129 @@
+{
+	"manufacturer": "Shelly Europe Ltd.",
+	"manufacturerId": "0x0460",
+	"label": "QLDM-0A101",
+	"description": "Wave Dimmer",
+	"devices": [
+		{
+			"productType": "0x0001",
+			"productId": "0x0083"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"$import": "templates/wave_template.json#switch_type",
+			"label": "SW1 Switch Type",
+			"defaultValue": 0
+		},
+		{
+			"#": "2",
+			"$import": "templates/wave_template.json#switch_type",
+			"label": "SW2 Switch Type",
+			"defaultValue": 0
+		},
+		{
+			"#": "131",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Dual Button Mode SW1 & SW2"
+		},
+		{
+			"#": "7",
+			"$import": "templates/wave_template.json#detached_mode",
+			"label": "Detach O1 Output"
+		},
+		{
+			"#": "8",
+			"$import": "templates/wave_template.json#detached_mode",
+			"label": "Detach O2 Output"
+		},
+		{
+			"#": "17",
+			"$import": "~/templates/master_template.json#state_after_power_failure_prev_off",
+			"label": "O1: State After Power Failure"
+		},
+		{
+			"#": "19",
+			"$import": "templates/wave_template.json#auto_off_timer",
+			"label": "O1: Auto-Off Timer"
+		},
+		{
+			"#": "20",
+			"$import": "templates/wave_template.json#auto_on_timer",
+			"label": "O1: Auto-On Timer"
+		},
+		{
+			"#": "25",
+			"$import": "templates/wave_template.json#timer_unit",
+			"label": "O1: Auto-On/Off Timer Unit"
+		},
+		{
+			"#": "36",
+			"$import": "templates/wave_template.json#power_change_report_treshold",
+			"label": "O1: Power Change Report Threshold"
+		},
+		{
+			"#": "39",
+			"$import": "templates/wave_template.json#min_time_between_reports",
+			"label": "O1: Minimum Time Between Power Reports"
+		},
+		{
+			"#": "78",
+			"$import": "templates/wave_template.json#force_calibration",
+			"label": "Calibrate Device"
+		},
+		{
+			"#": "121",
+			"$import": "templates/wave_template.json#max_dimming_value",
+			"label": "O1: Maximum Dim Level"
+		},
+		{
+			"#": "123",
+			"$import": "templates/wave_template.json#min_dimming_value",
+			"label": "O1: Minimum Dim Level"
+		},
+		{
+			"#": "125",
+			"$import": "templates/wave_template.json#dimming_time",
+			"label": "O1: Dimming Time (Short Press)"
+		},
+		{
+			"#": "127",
+			"$import": "templates/wave_template.json#fade_rate",
+			"label": "O1: Fade Rate (Long Press)"
+		},
+		{
+			"#": "129",
+			"$import": "~/templates/master_template.json#base_1-99_nounit",
+			"label": "O1: Minimum Turn-On Brightness",
+			"defaultValue": 15
+		},
+		{
+			"#": "117",
+			"$import": "templates/wave_template.json#remote_reboot",
+			"label": "Remote Reboot"
+		},
+		{
+			"#": "201",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 1"
+		},
+		{
+			"#": "202",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 2"
+		},
+		{
+			"#": "203",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 3"
+		}
+	],
+	"metadata": {
+		"$import": "templates/wave_template.json#default_metadata"
+	}
+}

package/config/devices/0x0460/qlht-OU2Z.json

@@ -0,0 +1,70 @@
+{
+	"manufacturer": "Shelly Europe Ltd.",
+	"manufacturerId": "0x0460",
+	"label": "QLHT-OU2Z",
+	"description": "Shelly Wave H&T Sensor",
+	"devices": [
+		{
+			"productType": "0x0100",
+			"productId": "0x0083"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"paramInformation": [
+		{
+			"#": "161",
+			"$import": "templates/wave_template.json#treshold_50",
+			"label": "Temperature Treshold"
+		},
+		{
+			"#": "162",
+			"$import": "templates/wave_template.json#temperature_offset",
+			"label": "Temperature Offset"
+		},
+		{
+			"#": "163",
+			"$import": "templates/wave_template.json#treshold_50",
+			"label": "Humidity Treshold"
+		},
+		{
+			"#": "164",
+			"$import": "templates/wave_template.json#humidity_offset",
+			"label": "Humidity Offset"
+		},
+		{
+			"#": "119",
+			"$import": "templates/wave_template.json#power_source_selection",
+			"label": "Power Source Selection"
+		},
+		{
+			"#": "117",
+			"$import": "templates/wave_template.json#remote_reboot",
+			"label": "Remote Reboot"
+		},
+		{
+			"#": "120",
+			"$import": "templates/wave_template.json#factory_reset"
+		},
+		{
+			"#": "201",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 1"
+		},
+		{
+			"#": "202",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 2"
+		},
+		{
+			"#": "203",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 3"
+		}
+	],
+	"metadata": {
+		"$import": "templates/wave_template.json#default_metadata"
+	}
+}

package/config/devices/0x0460/qlmo-003F.json

@@ -0,0 +1,70 @@
+{
+	"manufacturer": "Shelly Europe Ltd.",
+	"manufacturerId": "0x0460",
+	"label": "QLMO-003F",
+	"description": "Shelly Wave Motion Sensor",
+	"devices": [
+		{
+			"productType": "0x0100",
+			"productId": "0x0082"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"paramInformation": [
+		{
+			"#": "155",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Illumination Mesurement"
+		},
+		{
+			"#": "157",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "LED Detection Indication"
+		},
+		{
+			"#": "158",
+			"$import": "templates/wave_template.json#motion_sensitivity",
+			"label": "Motion Sensitivity"
+		},
+		{
+			"#": "159",
+			"$import": "templates/wave_template.json#motion_blind_time",
+			"label": "Motion Blind Time"
+		},
+		{
+			"#": "160",
+			"$import": "templates/wave_template.json#no_detection_time",
+			"label": "Motion No Detection Time"
+		},
+		{
+			"#": "117",
+			"$import": "templates/wave_template.json#remote_reboot",
+			"label": "Remote Reboot"
+		},
+		{
+			"#": "120",
+			"$import": "templates/wave_template.json#factory_reset"
+		},
+		{
+			"#": "201",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 1"
+		},
+		{
+			"#": "202",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 2"
+		},
+		{
+			"#": "203",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 3"
+		}
+	],
+	"metadata": {
+		"$import": "templates/wave_template.json#default_metadata"
+	}
+}

package/config/devices/0x0460/templates/wave_template.json

@@ -46,7 +46,23 @@
 				"value": 0
 			},
 			{
-				"label": "Swapped (O1 - close, O2 - open)",
+				"label": "Swapped",
+				"value": 1
+			}
+		]
+	},
+	"detached_mode": {
+		"label": "Detached Mode",
+		"valueSize": 1,
+		"defaultValue": 0,
+		"allowManualEntry": false,
+		"options": [
+			{
+				"label": "Normal",
+				"value": 0
+			},
+			{
+				"label": "Detached",
 				"value": 1
 			}
 		]
@@ -78,6 +94,7 @@
 		]
 	},
 	"timer_unit": {
+		"description": "The value is rounded up to the next multiple of 10. Values 1-10 = 10ms, 11-20 = 20ms, ...",
 		"valueSize": 1,
 		"defaultValue": 0,
 		"allowManualEntry": false,
@@ -275,6 +292,74 @@
 			}
 		]
 	},
+	"power_source_selection": {
+		"valueSize": 1,
+		"defaultValue": 0,
+		"allowManualEntry": false,
+		"options": [
+			{
+				"label": "Battery",
+				"value": 0
+			},
+			{
+				"label": "Mains",
+				"value": 1
+			}
+		]
+	},
+	"motion_sensitivity": {
+		"valueSize": 1,
+		"defaultValue": 1,
+		"allowManualEntry": false,
+		"options": [
+			{
+				"label": "Low",
+				"value": 0
+			},
+			{
+				"label": "Medium",
+				"value": 1
+			},
+			{
+				"label": "High",
+				"value": 2
+			}
+		]
+	},
+	"motion_blind_time": {
+		"valueSize": 1,
+		"unit": "seconds",
+		"minValue": 2,
+		"maxValue": 8,
+		"defaultValue": 5
+	},
+	"treshold_50": {
+		"valueSize": 1,
+		"minValue": 1,
+		"maxValue": 50,
+		"defaultValue": 1
+	},
+	"temperature_offset": {
+		"valueSize": 2,
+		"unit": "°C / °F",
+		"minValue": -500,
+		"maxValue": 500,
+		"defaultValue": 0
+	},
+	"humidity_offset": {
+		"valueSize": 2,
+		"unit": "RH %",
+		"minValue": -50,
+		"maxValue": 50,
+		"defaultValue": 0
+	},
+	"no_detection_time": {
+		"description": "Time after last motion before device reports no motion",
+		"valueSize": 2,
+		"minValue": 0,
+		"maxValue": 32535,
+		"defaultValue": 30
+	},
 	"default_metadata": {
 		"inclusion": "6.1 Adding the Device to a Z-Wave™ network (inclusion)\nNote! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.\n\n6.1.1 SmartStart adding (inclusion)\nSmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity.\n1. With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway.\n2. Connect the Device to a power supply.\n3. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.\n4. Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave™ network automatically.\n5. The blue LED will be blinking in Mode 2 during the adding process.\n6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.\n\n6.1.2 Adding (inclusion) with a switch/push-button\n1. Connect the Device to a power supply.\n2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.\n3. Enable add/remove mode on the gateway.\n4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode*). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.\n5. The blue LED will be blinking in Mode 2 during the adding process.\n6. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.\n*Learn mode - a state that allows the Device to receive network information from the gateway.\n\n6.1.3 Adding (inclusion) with the S button\n1. Connect the Device to a power supply.\n2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave™ network.\n3. Enable add/remove mode on the gateway.\n4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.\n5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.\n6. The blue LED will be blinking in Mode 2 during the adding process.\n7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave™ network.\nNote! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode",
 		"exclusion": "Removing the Device from a Z-Wave™ network (exclusion)\nNote! The Device will be removed from your Z-wave™ network, but any custom configuration parameters will not be erased.\nNote! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave™ network.\n\n6.2.1 Removing (exclusion) with a switch/push-button\n1. Connect the Device to a power supply.\n2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.\n3. Enable add/remove mode on the gateway.\n4. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times.\n5. The blue LED will be blinking in Mode 2 during the removing process.\n6. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.\n\n6.2.2 Removing (exclusion) with the S button\n1. Connect the Device to a power supply.\n2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave™ network.\n3. Enable add/remove mode on the gateway.\n4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.\n5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.\n6. The blue LED will be blinking in Mode 2 during the removing process.\n7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave™ network.\nNote! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode",

package/config/devices/0x046a/WB04V.json

@@ -341,8 +341,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/config/devices/0x046a/WM25L.json

@@ -238,8 +238,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote:Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "@zwave-js/config",
-  "version": "15.7.0",
+  "version": "15.8.0",
   "description": "zwave-js: configuration files",
   "keywords": [],
   "publishConfig": {