@zwave-js/config 8.9.2 → 8.10.1

package/config/devices/0x028c/pwly-7828-a1.json

@@ -0,0 +1,289 @@
+{
+	"manufacturer": "Powerley",
+	"manufacturerId": "0x028c",
+	"label": "PWLY-7828-A1",
+	"description": "Thermostat",
+	"devices": [
+		{
+			"productType": "0xa55a",
+			"productId": "0x0001",
+			"zwaveAllianceId": 2401
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Display Units",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 1,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Celsius",
+					"value": 0
+				},
+				{
+					"label": "Fahrenheit",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "2",
+			"label": "HVAC Settings",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 5,
+			"defaultValue": 1,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "1 Stage Conventional",
+					"value": 0
+				},
+				{
+					"label": "2 Stage Conventional",
+					"value": 1
+				},
+				{
+					"label": "Heat Pump with O-Wire",
+					"value": 2
+				},
+				{
+					"label": "Heat Pump with B-Wire",
+					"value": 3
+				},
+				{
+					"label": "Heat Pump with O-Wire and Aux Heating",
+					"value": 4
+				},
+				{
+					"label": "Heat Pump with B-Wire and Aux Heating",
+					"value": 5
+				}
+			]
+		},
+		{
+			"#": "3",
+			"label": "ECO Mode",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "Enable",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "4",
+			"label": "Thermostat Default Settings",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"options": [
+				{
+					"label": "No Change",
+					"value": 0
+				},
+				{
+					"label": "Restore thermostat factory settings (excluding Z-Wave settings)",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "5",
+			"label": "Temperature Calibration",
+			"valueSize": 1,
+			"minValue": -5,
+			"maxValue": 5,
+			"defaultValue": 0,
+			"unit": "°F",
+			"options": [
+				{
+					"label": "No change",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "6",
+			"label": "LED Dimming",
+			"description": "When powered via C-Wire",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 3,
+			"defaultValue": 3,
+			"options": [
+				{
+					"label": "Low",
+					"value": 0
+				},
+				{
+					"label": "Medium",
+					"value": 1
+				},
+				{
+					"label": "High",
+					"value": 2
+				},
+				{
+					"label": "Auto",
+					"value": 3
+				}
+			]
+		},
+		{
+			"#": "7",
+			"label": "Demand Response Mode",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "Enable",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "8",
+			"label": "Swing Setting",
+			"description": "Number of degrees from the set point at which the HVAC will turn on",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 10,
+			"defaultValue": 1,
+			"unit": "°F",
+			"options": [
+				{
+					"label": "No swing",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "9",
+			"label": "Differential Setting",
+			"description": "Number of degrees from the set point at which the 2nd stage will engage",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 10,
+			"defaultValue": 3,
+			"unit": "°F",
+			"options": [
+				{
+					"label": "No differential",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "10",
+			"label": "OTA (Over The Air) Programming Error Code",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 10,
+			"defaultValue": 0,
+			"readOnly": true,
+			"options": [
+				{
+					"label": "No error",
+					"value": 0
+				},
+				{
+					"label": "Battery low, reflashing not possible",
+					"value": 1
+				},
+				{
+					"label": "OTA Cancelled before completion",
+					"value": 2
+				},
+				{
+					"label": "Fragment CRC error",
+					"value": 3
+				},
+				{
+					"label": "Total image CRC error",
+					"value": 4
+				},
+				{
+					"label": "External flash error",
+					"value": 5
+				},
+				{
+					"label": "Fragment received out of order",
+					"value": 6
+				},
+				{
+					"label": "Invalid firmware or manufacture ID",
+					"value": 7
+				},
+				{
+					"label": "OTA session not properly initialized",
+					"value": 8
+				},
+				{
+					"label": "Same image currently running",
+					"value": 9
+				},
+				{
+					"label": "Time out during OTA download between fragments",
+					"value": 10
+				}
+			]
+		},
+		{
+			"#": "11",
+			"label": "Display On in C-Wire Powered Mode",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 1,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "Enable",
+					"value": 1
+				}
+			]
+		}
+	],
+	"metadata": {
+		"inclusion": "Press and hold Mode (circle on front of thermostat) for 5 seconds. CONNECT will scroll across the thermostat display once in inclusion mode. SUCCESS will scroll across the thermostat display once included. FAIL will scroll across the thermostat display if inclusion is unsuccessful, or if process takes longer than 1 minute.",
+		"exclusion": "Press and hold Mode (circle on front of thermostat) for 5 seconds to initiate Z-Wave exclusion process. DELETE will scroll across the thermostat display once in exclusion mode. To cancel the exclusion process, press Mode (circle on front of thermostat). To complete exclusion press either of the up/down arrows. SUCCESS will scroll across the thermostat display once excluded. NOTE: Excluding the thermostat will restore it to the default state for Z-Wave and temperature set points.",
+		"reset": "Turn the thermostat off by pressing Mode (circle on front of thermostat) repeatedly until OFF scrolls across the display, then press and hold the down and up Setpoint arrows at the same time for 5 sec. If successful, RESET will scroll across the display and the device will be restored to its default settings. NOTE: If a reset to factory default settings is performed, all settings including Z-Wave configuration parameter values and temperature setpoints will return to default values.",
+		"manual": "https://manuals-backend.z-wave.info/make.php?lang=en&sku=PWLY-7828-A1&cert=ZC10-17065620"
+	}
+}

package/config/devices/0x0300/7aa-ss-ve-a0.json

@@ -0,0 +1,117 @@
+{
+	"manufacturer": "LEEDARSON LIGHTING CO., Ltd.",
+	"manufacturerId": "0x0300",
+	"label": "7AA-SS-VE-A0",
+	"description": "Bypass Door Window Sensor Z-Wave 700",
+	"devices": [
+		{
+			"productType": "0x0301",
+			"productId": "0x0041",
+			"zwaveAllianceId": 4298
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		},
+		"2": {
+			"label": "On/Off Control",
+			"maxNodes": 5
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Magnetic Field Range",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Parameter 2: 1-19200 µT; Parameter 3: 1-8960 µT",
+					"value": 0
+				},
+				{
+					"label": "Parameter 2: 1-192000 µT; Parameter 3: 1-89600 µT",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "2",
+			"label": "Average Magnetic Field",
+			"valueSize": 4,
+			"unit": "µT",
+			"minValue": 1,
+			"maxValue": 192000,
+			"defaultValue": 640,
+			"unsigned": true
+		},
+		{
+			"#": "3",
+			"label": "Magnetic Field Offset",
+			"valueSize": 4,
+			"unit": "µT",
+			"minValue": 1,
+			"maxValue": 89600,
+			"defaultValue": 200,
+			"unsigned": true
+		},
+		{
+			"#": "10",
+			"label": "Low Battery Threshold",
+			"valueSize": 1,
+			"unit": "%",
+			"minValue": 5,
+			"maxValue": 50,
+			"defaultValue": 10,
+			"unsigned": true
+		},
+		{
+			"#": "14",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Basic Set Commands"
+		},
+		{
+			"#": "15",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Invert Sensor State"
+		},
+		{
+			"#": "20",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Bypass Mode",
+			"defaultValue": 1
+		},
+		{
+			"#": "21",
+			"label": "Temperature Reporting Interval",
+			"valueSize": 1,
+			"unit": "minutes",
+			"minValue": 15,
+			"maxValue": 127,
+			"defaultValue": 15,
+			"unsigned": true
+		},
+		{
+			"#": "254",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Lock Configuration"
+		}
+	],
+	"metadata": {
+		"inclusion": "1. Power on your Door Sensor, set your Z-Wave controller into add/inclusion mode.\n2. Trigger this action\n3. LED will flash green during the inclusion, and then solid green for 2 seconds to indicate the inclusion is successful, otherwise the LED will solid red for 2 seconds in which you need to repeat the process form step 2",
+		"exclusion": "1. Power on your Door Sensor, and let the Z-Wave primary controller into remove/exclusion mode.\n2. Trigger this action.\n3. LED will flash red during the exclusion, and then solid red for 2 seconds to indicate that the exclusion is successful, otherwise the LED will solid green for 2 seconds in which you need to repeat the process form step 2.",
+		"reset": "LED will blink red faster and faster within 5 seconds and then keep solid red until the button is released. Device will reset itself to factory default by sending a “Device Reset Locally Notification” to gateway when the button is released.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4298/zwave700%20DW%20sensor%207AA-SS-VE-A0%20user%20manual-20210910.pdf"
+	}
+}

package/config/devices/0x0300/7ba-kp-v-b-a0.json

@@ -0,0 +1,105 @@
+{
+	"manufacturer": "LEEDARSON LIGHTING CO., Ltd.",
+	"manufacturerId": "0x0300",
+	"label": "7BA-KP-V-B-A0",
+	"description": "Z-WAVE 700 Keypad",
+	"devices": [
+		{
+			"productType": "0x0301",
+			"productId": "0x0044",
+			"zwaveAllianceId": 4277
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Entry & Exit Delay",
+			"valueSize": 1,
+			"unit": "seconds",
+			"minValue": 0,
+			"maxValue": 30,
+			"defaultValue": 10,
+			"unsigned": true
+		},
+		{
+			"#": "2",
+			"label": "Low Battery Threshold",
+			"valueSize": 1,
+			"unit": "%",
+			"minValue": 5,
+			"maxValue": 50,
+			"defaultValue": 10,
+			"unsigned": true
+		},
+		{
+			"#": "3",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Proximity Sensor",
+			"defaultValue": 1
+		},
+		{
+			"#": "4",
+			"label": "Proximity Sensor: Timeout",
+			"valueSize": 1,
+			"unit": "seconds",
+			"minValue": 2,
+			"maxValue": 30,
+			"defaultValue": 5,
+			"unsigned": true
+		},
+		{
+			"#": "5",
+			"label": "Proximity Sensor: Sensitivity",
+			"valueSize": 1,
+			"minValue": 4,
+			"maxValue": 31,
+			"defaultValue": 9,
+			"unsigned": true
+		},
+		{
+			"#": "6",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Light Sensor",
+			"defaultValue": 1
+		},
+		{
+			"#": "7",
+			"label": "Day/Night Threshold",
+			"valueSize": 1,
+			"unit": "lux",
+			"minValue": 0,
+			"maxValue": 255,
+			"defaultValue": 50,
+			"unsigned": true
+		},
+		{
+			"#": "8",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Key Tones",
+			"defaultValue": 1
+		},
+		{
+			"#": "9",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Indicate Arm Status After Wakeup",
+			"defaultValue": 1
+		}
+	],
+	"metadata": {
+		"inclusion": "Add the Keypad into the Z-Wave network via SmartStart:\n1. Add Keypad DSK into the primary controller SmartStart Provisioning List (If you don’t know how to do this, refer to its manual).\n2. Power on the Keypad again.\n3. The Keypad will send “Z-Wave protocol Command Class” frame to start SmartStart Inclusion.\n4. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2\nNote: Keypad will reset itself to factory default by sending “Device Reset Locally CC” when it is included into a non-security Z-wave network.\nDSK QR code is on the left side of the product with laser printing.\nUser should follow the procedure in the section below if the controller does not support SmartStart inclusion.\n\nAdd the Keypad into the Z-Wave network:\n1. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).\n2. Trigger this action.\n3. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2.",
+		"exclusion": "Remove the Keypad from a Z-Wave network:\n1. Set the Z-Wave network main controller into removing mode (see Z-Wave controller operating manual).\n2. Trigger this button action. the Network LED will flashing at every 1 second.\n3. If the removing is successful, the LED will solid green for 3 seconds. If the removing is failed then LED display yellow for 3 seconds, otherwise you need to repeat the process from step 2.\nNote: Keypad will start SmartStart Inclusion when it is removed from a Z-wave network.",
+		"reset": "Reset the Keypad to factory default.\n1. Device will reset itself to factory default by sending a “Device Reset Locally Notification” to gateway.\n2. If triggered the factory reset, the network connection led will solid green while factory reset is completed.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4277/keypad%20quick%20guide%207BA-KP-V-B-A0%2020210811(updated).pdf"
+	}
+}

package/config/devices/0x0300/7ca-ss-ve-a0.json

@@ -0,0 +1,110 @@
+{
+	"manufacturer": "LEEDARSON LIGHTING CO., Ltd.",
+	"manufacturerId": "0x0300",
+	"label": "7CA-SS-VE-A0",
+	"description": "Z-WAVE 700 Motion Sensor Pet Immunity",
+	"devices": [
+		{
+			"productType": "0x0301",
+			"productId": "0x0042",
+			"zwaveAllianceId": 4297
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		},
+		"2": {
+			"label": "On/Off control",
+			"maxNodes": 5
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "10",
+			"label": "Low Battery Threshold",
+			"valueSize": 1,
+			"unit": "%",
+			"minValue": 5,
+			"maxValue": 50,
+			"defaultValue": 10,
+			"unsigned": true
+		},
+		{
+			"#": "12",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "PIR Sensor",
+			"defaultValue": 1
+		},
+		{
+			"#": "13",
+			"label": "PIR Timeout",
+			"valueSize": 2,
+			"unit": "seconds",
+			"minValue": 5,
+			"maxValue": 15300,
+			"defaultValue": 60,
+			"unsigned": true
+		},
+		{
+			"#": "14",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Basic Set Commands"
+		},
+		{
+			"#": "15",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Invert Basic Set Commands"
+		},
+		{
+			"#": "16",
+			"label": "PIR Sensitivity",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 10,
+			"defaultValue": 9,
+			"unsigned": true
+		},
+		{
+			"#": "17",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Pet Immunity Mode"
+		},
+		{
+			"#": "18",
+			"label": "Reporting Value",
+			"valueSize": 1,
+			"minValue": 1,
+			"maxValue": 3,
+			"defaultValue": 1,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Lumens only",
+					"value": 1
+				},
+				{
+					"label": "Day/Night notification",
+					"value": 2
+				},
+				{
+					"label": "Lumens and Day/Night notification",
+					"value": 3
+				}
+			]
+		}
+	],
+	"metadata": {
+		"inclusion": "Add the Motion Sensor into the Z-Wave network:\n5. Power on your Motion Sensor, and let your Z-Wave controller into add/inclusion mode.\n6. 3 consecutive clicks in 1.5 seconds, the Motion Sensor will send out a node info security CC in command class list (Security inclusion), the LED will be fast blink ,the timeout is 20-40 seconds;\n7. If the inclusion is successful, the LED will be turn on within 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above.",
+		"exclusion": "Remove Motion Sensor from a Z-Wave network:\n1. Power on your Motion Sensor, and let the Z-Wave primary controller into remove mode.\n2. 3 consecutive clicks in 1.5 second, the LED will be fast blink ,the timeout is 20-40 seconds;\n3. If Motion Sensor has been successfully removed from your Z-Wave\nnetwork, the LED will be turn on 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above.",
+		"reset": "Reset Motion Sensor to factory default.\n\n1. Triggering this action, in 5 seconds LED will be accelerate blink. After 5 seconds, the LED will remain on until the key is released. Motion Sensor will send “Device_Reset_Locally” to the main controller and exclude from the Z-Wave network when the button is released, this procedure will reset the sensor to factory default.\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n3. When not in the network, triggering this action, in 5 seconds LED will be accelerate blink red. After 5 seconds, the LED will remain on red until the key is released. this procedure will reset the sensor to factory default.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4297/user%20manual%2003.13%207CA-SS-VE-A0-20210910.pdf"
+	}
+}