@zwave-js/config 8.9.2 → 8.10.1

package/config/devices/0x019b/zm_thermostat_16.json

@@ -0,0 +1,159 @@
+{
+	"manufacturer": "Heatit",
+	"manufacturerId": "0x019b",
+	"label": "ZM THERMOSTAT 16A",
+	"description": "Floor Thermostat",
+	"devices": [
+		{
+			"productType": "0x0004",
+			"productId": "0x3502",
+			"zwaveAllianceId": 4305
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		},
+		"2": {
+			"label": "External control",
+			"maxNodes": 5
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Operating Mode",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 2,
+			"defaultValue": 1,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Off,",
+					"value": 0
+				},
+				{
+					"label": "Heat",
+					"value": 1
+				},
+				{
+					"label": "Cool",
+					"value": 2
+				}
+			]
+		},
+		{
+			"#": "2",
+			"label": "Temperature Control Hysteresis",
+			"valueSize": 1,
+			"unit": "0.1 °C",
+			"minValue": 3,
+			"maxValue": 30,
+			"defaultValue": 5,
+			"unsigned": true
+		},
+		{
+			"#": "3",
+			"label": "Minimum Setpoint Temperature",
+			"valueSize": 2,
+			"unit": "0.1 °C",
+			"minValue": 50,
+			"maxValue": 400,
+			"defaultValue": 50,
+			"unsigned": true
+		},
+		{
+			"#": "4",
+			"label": "Maximum Setpoint Temperature",
+			"valueSize": 2,
+			"unit": "0.1 °C",
+			"minValue": 50,
+			"maxValue": 400,
+			"defaultValue": 400,
+			"unsigned": true
+		},
+		{
+			"#": "5",
+			"label": "Current Setpoint",
+			"valueSize": 2,
+			"minValue": 50,
+			"maxValue": 400,
+			"defaultValue": 210,
+			"unsigned": true
+		},
+		{
+			"#": "6",
+			"label": "Sensor Calibration",
+			"valueSize": 1,
+			"unit": "0.1 °C",
+			"minValue": -60,
+			"maxValue": 60,
+			"defaultValue": 0
+		},
+		{
+			"#": "7",
+			"label": "Temperature Reporting Interval",
+			"valueSize": 2,
+			"unit": "seconds",
+			"minValue": 30,
+			"maxValue": 65535,
+			"defaultValue": 1020,
+			"unsigned": true
+		},
+		{
+			"#": "8",
+			"label": "Temperature Report Hysteresis",
+			"valueSize": 1,
+			"unit": "°C",
+			"minValue": 0,
+			"maxValue": 100,
+			"defaultValue": 10,
+			"unsigned": true,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "9",
+			"label": "Meter Reporting Interval",
+			"valueSize": 2,
+			"unit": "seconds",
+			"minValue": 30,
+			"maxValue": 65535,
+			"defaultValue": 1020,
+			"unsigned": true
+		},
+		{
+			"#": "10",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Inverted Output"
+		},
+		{
+			"#": "11",
+			"label": "Relay State Update Interval",
+			"valueSize": 2,
+			"unit": "seconds",
+			"minValue": 30,
+			"maxValue": 65535,
+			"defaultValue": 43200,
+			"unsigned": true
+		}
+	],
+	"metadata": {
+		"inclusion": "The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode.\n\nThere are two ways to add the device to a Z-Wave network.\nMethod 1: Standard (Manual)\nAdd mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been added to the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if adding is successful.\nThe device is now ready for use with default settings.\n\nMethod 2: SmartStart (Automatic)\nSmartStart enabled products may be added to a Z-Wave network by scanning the Z-Wave QR-Code on the product if your primary controller supports SmartStart inclusion. No further action is required and the SmartStart product will be added automatically after being powered on within range of the primary controller.",
+		"exclusion": "The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode.\n\nRemove mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been removed from the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if removing is successful",
+		"reset": "Press and hold the configuration button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will start to blink green rapidly for 5 seconds. You may now release the button",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4305/Manual_Heatit_ZM_Thermostat%2016A.pdf"
+	}
+}

package/config/devices/0x021d/ml2.json

@@ -0,0 +1,120 @@
+{
+	"manufacturer": "Shenzhen Kaadas Intelligent Technology Co., Ltd.",
+	"manufacturerId": "0x021d",
+	"label": "ML2",
+	"description": "Digital Mortise Door Lock",
+	"devices": [
+		{
+			"productType": "0x0103",
+			"productId": "0x0003",
+			"zwaveAllianceId": 4120
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		},
+		"2": {
+			"label": "On/Off Control",
+			"maxNodes": 5
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Configure Volume Level",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 2,
+			"defaultValue": 2,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Silent",
+					"value": 0
+				},
+				{
+					"label": "Low",
+					"value": 1
+				},
+				{
+					"label": "High",
+					"value": 2
+				}
+			]
+		},
+		{
+			"#": "2",
+			"$import": "~/templates/master_template.json#enable_led_indicator"
+		},
+		{
+			"#": "3",
+			"label": "Battery Reporting Interval",
+			"valueSize": 2,
+			"unit": "minutes",
+			"minValue": 0,
+			"maxValue": 14400,
+			"defaultValue": 1440,
+			"unsigned": true,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "4",
+			"label": "Basic Set Value",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 6,
+			"defaultValue": 1,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "0xff on unlock, 0x00 on lock",
+					"value": 1
+				},
+				{
+					"label": "0x00 on unlock, 0xff on lock",
+					"value": 2
+				},
+				{
+					"label": "0xff on unlock",
+					"value": 3
+				},
+				{
+					"label": "0x00 on lock",
+					"value": 4
+				},
+				{
+					"label": "0x00 on unlock",
+					"value": 5
+				},
+				{
+					"label": "0xff on lock",
+					"value": 6
+				}
+			]
+		}
+	],
+	"metadata": {
+		"inclusion": "1. Follow the user guide of hub to enter inclusion mode.\n2. Operate on lock following guide below:\n 1) Enter master mode(** + Master PIN Code + √)\n 2) Input “8” to enter “function extension settings”\n 3) Input “1” to enter “Inclusion mode”",
+		"exclusion": "1. Follow the user guide of hub to enter exclusion mode.\n2. Operate on lock following guide below:\n 1) Enter master mode(** + Master PIN Code + √)\n 2) Input “8” to enter “function extension settings”\n 3) Input “2” to enter “Exclusion mode”",
+		"reset": "1) Open the door and keep the lock in \"unlock\" status\n 2) Open battery box and find the reset button. \n 3) Use a sharp thing to press and hold the reset button.\n 4) Keep holding the reset button and remove the battery from battery box then replace it.\n 5) Keep holding the reset button down until you hear the lock beep (Can take up to 10 seconds).\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4120/ML2%20-%20Product%20Manual_new.pdf"
+	}
+}

package/config/devices/0x0234/zdb5100.json

@@ -711,5 +711,9 @@
 		"exclusion": "Remove white button cover and press on the center switch with a non-conductive object. The LEDs will now start blinking on button 1 (upper left button)",
 		"reset": "Remove white button cover and long-press the center switch for 10 seconds with a non-conductive object. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3399/MATRIX_ZDB5100_User_Manual_1_01-EN.pdf"
+	},
+	"compat": {
+		// Starting in Firmware 1.6, the device no longer uses Central Scene for Pressed / Released, only Basic CC
+		"disableBasicMapping": true
 	}
 }

package/config/devices/0x0244/homey.json

@@ -7,7 +7,7 @@
 		{
 			"productType": "0xba5e",
 			"productId": "0x0001",
-			"zwaveAllianceId": 1771
+			"zwaveAllianceId": [1771, 4208]
 		}
 	],
 	"firmwareVersion": {
@@ -16,6 +16,6 @@
 	},
 	"metadata": {
 		"reset": "To Reset Homey to factory defaults, place Homey upside down. After a few seconds, Homey will initiate a countdown (both visually in the LED ring and verbally trough voice) of 15 seconds. After the countdown had ended, browse on a computer, laptop or tablet to setup.athom.com to initiate a new setup. PLEASE USE THE RESET PROCEDURE ONLY IF YOU EXPERIENCE SEVERE DIFFICULTIES WITH HOMEY'S OPERATING SYSTEM OR WHEN ADVISED TO DO SO BY ATHOM SUPPORT",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1771/athomhomeymanualzwave.docx"
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4208/athomhomeymanualzwave.pdf"
 	}
 }

package/config/devices/0x0258/nas-pd07u1.json

@@ -64,7 +64,6 @@
 		{
 			"#": "5",
 			"label": "Binary Sensor Report on Motion",
-			"description": "If enabled, a Binary Sensor report will be sent on Motion",
 			"valueSize": 1,
 			"minValue": 0,
 			"maxValue": 1,

package/config/devices/0x0258/nas-wr01ze.json

@@ -153,5 +153,11 @@
 			"maxValue": 16,
 			"defaultValue": 13
 		}
-	]
+	],
+	"metadata": {
+		"comments": {
+			"level": "warning",
+			"text": "This device is buggy and sends large negative Meter Reports from time to time. "
+		}
+	}
 }

package/config/devices/0x0258/neo-ds07z.json

@@ -0,0 +1,156 @@
+{
+	"manufacturer": "Shenzhen Neo Electronics Co., Ltd.",
+	"manufacturerId": "0x0258",
+	"label": "NEO-DS07Z",
+	"description": "Door/Window Sensor Plus",
+	"devices": [
+		{
+			"productType": "0x0010",
+			"productId": "0x0702"
+		}
+	],
+	"firmwareVersion": {
+		"min": "2.0",
+		"max": "255.255"
+	},
+
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "LED Indication",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "Enable",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "2",
+			"label": "Binary Sensor Report",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 1,
+			"defaultValue": 0,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				},
+				{
+					"label": "Enable",
+					"value": 1
+				}
+			]
+		},
+		{
+			"#": "3",
+			"label": "Temperature Calibration",
+			"unit": "0.1 (°C/°F)",
+			"valueSize": 1,
+			"minValue": -120,
+			"maxValue": 121,
+			"defaultValue": 0,
+			"unsigned": false
+		},
+		{
+			"#": "4",
+			"label": "Humidity Offset Value",
+			"unit": "0.1 (RH%).",
+			"valueSize": 1,
+			"minValue": -120,
+			"maxValue": 120,
+			"defaultValue": 0,
+			"unsigned": false
+		},
+		{
+			"#": "5",
+			"label": "Temperature Change Report Threshold",
+			"unit": "0.1 (°C/°F)",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 100,
+			"defaultValue": 10,
+			"unsigned": true
+		},
+		{
+			"#": "6",
+			"label": "Humidity Change Report Threshold",
+			"unit": "0.1 %rH",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 100,
+			"defaultValue": 20,
+			"unsigned": true
+		},
+		{
+			"#": "7",
+			"label": "Association Group 2: Basic Set Value (Open)",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 100,
+			"defaultValue": 100,
+			"unsigned": true,
+			"options": [
+				{
+					"label": "Off (0x00)",
+					"value": 0
+				},
+				{
+					"label": "On (0xff)",
+					"value": 100
+				}
+			]
+		},
+		{
+			"#": "8",
+			"label": "Association Group 2: Basic Set Off Delay (Close)",
+			"unit": "seconds",
+			"valueSize": 2,
+			"minValue": 0,
+			"maxValue": 30000,
+			"defaultValue": 0,
+			"unsigned": true,
+			"options": [
+				{
+					"label": "No Delay",
+					"value": 0
+				}
+			]
+		},
+		{
+			"#": "9",
+			"label": "Sensor Measuring Interval",
+			"unit": "seconds",
+			"valueSize": 2,
+			"minValue": 0,
+			"maxValue": 30000,
+			"defaultValue": 0,
+			"unsigned": true,
+			"options": [
+				{
+					"label": "Disable",
+					"value": 0
+				}
+			]
+		}
+	],
+
+	"metadata": {
+		"inclusion": "1. Power Up The Device.\n2. Set Z-Wave Controller Into Inclusion Mode\n3. Press And Hold The Button For 5s Until White Led Lights Is On, Then Release The Button Before Led Turn Off.\nBlue Led Will Blink With 1s Interval Until Inclusion Successful.",
+		"exclusion": "1. Power Up The Device.\n2. Set Z-Wave Controller Into Exclusion Mode\n3. Press And Hold The Button For 5s Until White Led Lights Is On, Then Release The Button Before Led Turn Off.\nBlue Led Will Blink With 0.5sinterval Until Exclusion Successful.",
+		"reset": "1. Power Up The Device.\n2. Press And Hold The Button For 10s Until Pink Led Lights Is On, Then Release The Button Before Led Turn Off."
+	}
+}

package/config/devices/0x025b/ezlopl.json

@@ -0,0 +1,28 @@
+{
+	"manufacturer": "AdTrustMedia LLC dba: eZLO",
+	"manufacturerId": "0x025b",
+	"label": "EZLOPL",
+	"description": "Ezlo Plus",
+	"devices": [
+		{
+			"productType": "0x0004",
+			"productId": "0x0001",
+			"zwaveAllianceId": 4308
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 232,
+			"isLifeline": true
+		}
+	},
+	"metadata": {
+		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector. Push and hold the RESET button for at least 5 sec (on Ezlo Plus LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults. Reset to Factory Settings remove all the information about added devices and reset Z-Wave chip (new Home ID, new S0/S2 keys, remove all Z-Wave nodes), scenes created, House modes settings, etc. The process is irreversible",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4308/Ezlo%20Plus%20User%20Manual.pdf"
+	}
+}

package/config/devices/0x025b/ezlosecure.json

@@ -0,0 +1,28 @@
+{
+	"manufacturer": "AdTrustMedia LLC dba: eZLO",
+	"manufacturerId": "0x025b",
+	"label": "EZLOSECURE",
+	"description": "Ezlo Secure",
+	"devices": [
+		{
+			"productType": "0x0005",
+			"productId": "0x0001",
+			"zwaveAllianceId": 4111
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 232,
+			"isLifeline": true
+		}
+	},
+	"metadata": {
+		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector.\nPush and hold the RESET button for at least 5 sec (on Ezlo Secure LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults.\nReset to Factory Settings remove all the information about added devices\nand reset ZWave chip (new Home ID, new S0/S2 keys, remove all Z-Wave\nnodes), scenes created, House modes settings, etc. The process is\nirreversible.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4111/Ezlo%20Secure%20User%20Manual.pdf"
+	}
+}

package/config/devices/0x027a/zen17.json

@@ -7,6 +7,11 @@
 		{
 			"productType": "0x7000",
 			"productId": "0xa00a"
+		},
+		{
+			"productType": "0xbb00",
+			"productId": "0xbb0a",
+			"zwaveAllianceId": 4132
 		}
 	],
 	"firmwareVersion": {
@@ -533,5 +538,11 @@
 	"compat": {
 		// This device improperly reports the state of R2 (endpoint 2) through the root endpoint in a way that also changes the state of R1 (endpoint 1)
 		"preserveRootApplicationCCValueIDs": true
+	},
+	"metadata": {
+		"inclusion": "INCLUSION\n1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "1. Bring your Universal Relay close to the Z-Wave hub and power it\n2. Put the Z-Wave hub into exclusion mode\n3. Click the Z-Wave button 3 times quickly\n4. Your hub will confirm exclusion and the Universal Relay will disappear from your controller's device list",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, click the Z-Wave button 4 times quickly, the LED indicator will light up,\nthen quickly click the Z-Wave button 4 times again. The LED indicator will flash 3 times to confirm successful reset and will then turn off",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4132/zooz-700-series-z-wave-plus-universal-relay-zen17-ver1.0-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen32.json

@@ -7,6 +7,11 @@
 		{
 			"productType": "0x7000",
 			"productId": "0xa008"
+		},
+		{
+			"productType": "0xbb00",
+			"productId": "0xbb08",
+			"zwaveAllianceId": 4131
 		}
 	],
 	"firmwareVersion": {
@@ -551,5 +556,11 @@
 				}
 			]
 		}
-	]
+	],
+	"metadata": {
+		"inclusion": "INCLUSION\n1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP THE SWITCH BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "EXCLUSION\n1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. TAP THE SWITCH BUTTON 3 TIMES QUICKLY (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list\nreset",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the switch button for 20 seconds until the LED indicator starts flashing red. Release the button, and immediately a􀆞er, tap remote button 1 once to complete the reset. The LED indicators on all buttons will flash red to confirm a successful reset",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4131/zooz-z-wave-plus-scene-control-switch-zen32-online-manual.pdf"
+	}
 }

package/config/devices/0x027a/zen34.json

@@ -5,12 +5,13 @@
 	"description": "Z-Wave Plus 700 Series Remote Switch",
 	"devices": [
 		{
-			"productType": "0x7000",
+			"productType": "0x0004",
 			"productId": "0xf001"
 		},
 		{
-			"productType": "0x0004",
-			"productId": "0xf001"
+			"productType": "0x7000",
+			"productId": "0xf001",
+			"zwaveAllianceId": 4114
 		}
 	],
 	"firmwareVersion": {
@@ -138,5 +139,11 @@
 				}
 			]
 		}
-	]
+	],
+	"metadata": {
+		"inclusion": "Put your Z-Wave hub into inclusion mode and click the upper paddle 6 times quickly. The LED indicator\nwill blink blue during the process and light up green once added successfully. It will light up red if failed",
+		"exclusion": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the lower paddle 6 times very quickly\n4. Your hub will confirm exclusion and the device will disappear from your controller's device list",
+		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the process, make sure the device is powered, then tap-tap-\ntap’and’hold the upper paddle. The LED indicator will blink red 5 times to indicate successful reset",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4114/zooz-700-series-remote-switch-zen34-manual-online.pdf"
+	}
 }

package/config/devices/0x027a/zen71.json

@@ -6,7 +6,8 @@
 	"devices": [
 		{
 			"productType": "0x7000",
-			"productId": "0xa001"
+			"productId": "0xa001",
+			"zwaveAllianceId": 4103
 		}
 	],
 	"firmwareVersion": {
@@ -109,5 +110,11 @@
 				}
 			]
 		}
-	]
+	],
+	"metadata": {
+		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. Finalize inclusion at the switch. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion",
+		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4103/zooz-700-series-switch-zen71-manual.pdf"
+	}
 }

package/config/devices/0x027a/zen72.json

@@ -6,7 +6,8 @@
 	"devices": [
 		{
 			"productType": "0x7000",
-			"productId": "0xa002"
+			"productId": "0xa002",
+			"zwaveAllianceId": 4108
 		}
 	],
 	"firmwareVersion": {
@@ -147,5 +148,11 @@
 			"#": "22",
 			"$import": "templates/zooz_template.json#night_light_mode"
 		}
-	]
+	],
+	"metadata": {
+		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails",
+		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4108/zooz-700-series-z-wave-dimmer-zen72-manual.pdf"
+	}
 }