@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x0129/ntb632-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4662/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntb642-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4663/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntm610.json

@@ -85,9 +85,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2966/nexTouchSectionalMortise_ZWavePlusSystemIntegratorsGuide_NTM.pdf"
 	}
 }

package/config/devices/0x0129/ntm612-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4632/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm617-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4633/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm622-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4622/Binder2.pdf"
 	}
 }

package/config/devices/0x0129/ntm625.json

@@ -93,9 +93,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2954/nexTouch%20Sectional%20Mortise%20with%20ZW2.pdf"
 	}
 }

package/config/devices/0x0129/ntm627-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4634/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm632-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4635/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm637-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4636/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm642-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4637/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntm647-zw2.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the reset button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\" after 15 seconds.\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4638/ntm612%20manual.pdf"
 	}
 }

package/config/devices/0x0129/ntt610.json

@@ -73,9 +73,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3458/NTT610_620_YaleRealLivingAssureDeadbolt_Z-WavePlus_SystemIntegratorsGuid....pdf"
 	}
 }

package/config/devices/0x0129/ntt612-zw2.json

@@ -80,9 +80,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4664/NTT-2.pdf"
 	}
 }

package/config/devices/0x0129/ntt620-zw2.json

@@ -77,9 +77,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3463/NTT610_620_YaleRealLivingAssureDeadbolt_Z-WavePlus_SystemIntegratorsGuid....pdf"
 	}
 }

package/config/devices/0x0129/ntt622-zw2.json

@@ -80,9 +80,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. While pressing the reset button above the PCB cable connector for 3 seconds, reinstall batteries.\n4. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4665/NTT-2.pdf"
 	}
 }

package/config/devices/0x0129/sd-l1000-ch.json

@@ -82,9 +82,9 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave controller into add or learn mode\n\nPress the R button on the lock 3 times quickly (within 1.5 seconds)\n\nRefer to the operation manual of the Z-Wave controller to complete the learn in process\n\nFor more information on this please visit:\nwww.yale.co.uk/smart-living",
-		"exclusion": "Put the existing Z-Wave controller into Remove Mode\n\nPress the R button on the lock 3 times quickly (within 1.5 secs)\n\nThe lock is now ready to be added to a new Z-Wave controller\n\nFor more information on this please visit:\nwww.yale.co.uk/smart-living",
-		"reset": "Only use this when the existing Z-Wave controller is missing or inoperable\n\n Lift up the lever handle\n\nWhile holding the handle up, press the R button 3 times within 1.5 seconds",
+		"inclusion": "Press the R button on the lock 3 times quickly within 1.5 seconds.",
+		"exclusion": "Press the R button on the lock 3 times quickly within 1.5 seconds.",
+		"reset": "1. Lift up the lever handle\n2. While holding the handle up, press the R button 3 times within 1.5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2535/Instruction%20Manual%20V2a.pdf"
 	}
 }

package/config/devices/0x0129/sr-bx-zw.json

@@ -52,9 +52,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "ADDING THE SIREN\nThis product can be added and operate in any compatible Z-Wave network. All non-battery operated nodes within the network will act as repeaters, regardless of vendor, to increase reliability of the network.\nAdding steps:\n• Turn on the battery power switch to activate\nthe pre-inserted batteries.\n• The Siren will emit a 2-tone beep.\n• Put the Z-Wave controller into adding or\nLearning mode (please refer to the Z-Wave\ncontroller manual).\n• Within 1.5 seconds, press the Siren learn button\n3 times.\n• Refer to the operation manual of the Z-Wave\ncontroller to complete the learn-in process.\n• If the Siren has already been added (learnt) into\nanother Z-Wave controller, or if the Siren is unable\nto be learnt into the current Z-Wave controller,\nplease remove it first (see Removing the siren below)\nbefore attempting to add it into the current\nZ-Wave controller",
-		"exclusion": "REMOVING THE SIREN\nThe Siren must be removed from any existing Z-Wave network before being added into a new Z-Wave network. There are two methods available to remove a device.\nRemoving Mode\n• Put the existing Z-Wave controller into Removing Mode (please refer to the Z-Wave controller manual).\n• Within 1.5 seconds, press the learn button 3 times and the Siren will be removed from the existing Z-Wave network.\n• The Siren is now ready to be added to a new Z-Wave controller",
-		"reset": "Factory Reset (Only use this when the existing Z-Wave controller is missing or inoperable).\n• Turn off battery power switch and disconnect 9V power adaptor (if present).\n• Press and hold the learn button.\n• While holding the learn button, power on the Siren (power switch ON and reconnect the 9V power adaptor). Keep holding for 10 seconds to complete the factory reset.\n• Please note that the existing Z-Wave controller will still retain the Siren's Z-Wave setting. Please refer to the Z-Wave controller manual on remove procedures. Only use this when the existing Z-Wave controller is missing or inoperable.\n• The Siren is now ready to be added to a new Z-Wave controller",
+		"inclusion": "1. Turn on the battery power switch to activate the pre-inserted batteries\n2. The Siren will emit a 2-tone beep\n3. Within 1.5 seconds, press the Siren learn button 3 times",
+		"exclusion": "Within 1.5 seconds, press the learn button 3 times and the Siren will be removed from the existing Z-Wave network.",
+		"reset": "1. Turn off battery power switch and disconnect 9V power adaptor if present\n2. Press and hold the learn button\n3. While holding the learn button, power on the Siren by turning power switch ON and reconnecting the 9V power adaptor\n4. Keep holding for 10 seconds to complete the factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2039/YSL_External_Siren_SR-BX-ZW_1C.pdf"
 	}
 }

package/config/devices/0x0129/templates/yale_template.json

@@ -591,13 +591,13 @@
 		}
 	},
 	"assure_zw3_metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key\n4. Enter the first 5 digits of the DSK when prompted",
-		"exclusion": "1. Enter the 4-8 digit master PIN code, followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.\n4. Enter the first 5 digits of the DSK when prompted.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4753/YRC622final.pdf"
 	},
 	"assure2_zw3_metadata": {
-		"inclusion": "1. Enter the 4-8 digit programming code, followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.\n4. Press the gear key again. The lock is now in Z-Wave inclusion mode for 30 seconds.",
-		"exclusion": "1. Enter the 4-8 digit programming code, followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"inclusion": "1. Enter the 4-8 digit programming code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.\n4. Press the gear key again. The lock is now in inclusion mode for 30 seconds.",
+		"exclusion": "1. Enter the 4-8 digit programming code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4753/YRC622final.pdf"
 	}
 }

package/config/devices/0x0129/yale_smart_door_lock_z-wave_module.json

@@ -97,9 +97,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave controller into add mode\n\nEnter the Master code on the lock, followed by #\n\nPress the 4 button, followed by #\n\nPress the 1 button followed by #\n\nRefer to the operation manual of the Z-Wave controller to complete the add/inclusion process\n\nFor more information on this please visit:\nwww.yale.co.uk/smart-living",
-		"exclusion": "Put the Z-Wave controller into remove mode\n\nEnter the Master code on the lock, followed by #\n\nPress the 4 button, followed by #\n\nPress the 3 button followed by #\n\nRefer to the operation manual of the Z-Wave controller to complete the remove/exclusion process\n\nFor more information on this please visit:\nwww.yale.co.uk/smart-living",
-		"reset": "Enter the Master code on the lock, followed by #\n\nPress the 4 button, followed by #\n\nPress the 0 button followed by #\n\nPlease use this procedure only when the network controller is missing or inoperable",
+		"inclusion": "1. Enter the Master code on the lock, followed by #\n2. Press the 4 button, followed by #\n3. Press the 1 button followed by #",
+		"exclusion": "1. Enter the Master code on the lock, followed by #\n2. Press the 4 button, followed by #\n3. Press the 3 button followed by #",
+		"reset": "1. Enter the Master code on the lock, followed by #\n2. Press the 4 button, followed by #\n3. Press the 0 button followed by #",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2576/Instruction%20Manual%20V2b.pdf"
 	}
 }

package/config/devices/0x0129/ydm3109.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To include:\n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,1,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
-		"exclusion": "To exclude:\n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,3,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
-		"reset": "To reset to factory defaults:\n ※ Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. (User code or master code remains the same. Only network settings reset to factory defaults.) \n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,9,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
+		"inclusion": "1. Touch keypad with palm\n2. Enter User code in Normal Mode or Master code in Master Mode\n3. Press 'I' button from inside the battery cover for Registration\n4. Press 9,#,1,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
+		"exclusion": "1. Touch keypad with palm\n2. Enter User code in Normal Mode or Master code in Master Mode\n3. Press 'I' button from inside the battery cover for Registration\n4. Press 9,#,3,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
+		"reset": "1. Touch keypad with palm\n2. Enter User code in Normal Mode or Master code in Master Mode\n3. Press 'I' button from inside the battery cover for Registration\n4. Press 9,#,9,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3227/Manual%20for%20YDM3109%20plus.pdf"
 	}
 }

package/config/devices/0x0129/ydm3109a.json

@@ -86,9 +86,9 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "How to add (pairing) the product into Z-Wave network\n 1. Operate on lock following guide below:\n 1) Enter Master Code-> 'R' -> '9' -> '#' -> '1' -> '#' (only can be activated in advanced mode)",
-		"exclusion": "How to remove the product from Z-Wave network\n 1. Operate on lock following guide below:\n 1) Enter Master Code-> 'R' -> '9' -> '#' -> '3' -> '#' ->  Master Code -> '#' (only can be activated in advanced mode)",
-		"reset": "How to factory reset for Z-Wave\nNote: please use this procedure only when the network primary controller is missing or otherwise inoperable.\n 1) Press and hold the \"factory reset\" key after the lock body\n 2) Power off the lock body for more than 5S, and plug in the battery again\n 3) Plug in the battery again and wait for 5S to release the \"factory reset\" key",
+		"inclusion": "1. Enter Master Code\n2. Press 'R' then '9' then '#' then '1' then '#'\n3. Note: Only available in advanced mode",
+		"exclusion": "1. Enter Master Code\n2. Press 'R' then '9' then '#' then '3' then '#'\n3. Enter Master Code then '#'\n4. Note: Only available in advanced mode",
+		"reset": "1. Press and hold the factory reset key behind the lock body\n2. Remove the battery for more than 5 seconds then reinstall it\n3. Wait 5 seconds then release the factory reset key",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/459/DoorLockManualforYDM3109A_4.docx"
 	}
 }

package/config/devices/0x0129/ydm4109plus.json

@@ -21,9 +21,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To include:\n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,1,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
-		"exclusion": "To exclude:\n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,3,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
-		"reset": "To reset to factory defaults:\n ※ Please use this procedure only when the network primary controller is missing or otherwise inoperable. (User code or master code remains the same. Only network settings reset to factory defaults.) \n1. Touch keypad with palm\n2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)\n3. Press 'I' button [Registration] from the inside of battery cover.\n4. Press 9,#,9,# on the keypad (by sequence)\n5. Wait until 'Ding dong dang' melody play then press 'I' button",
+		"inclusion": "1. Touch keypad with palm\n2. Enter User code in Normal Mode only. Enter Master code if operating Master Mode.\n3. Press 'I' button for Registration from inside the battery cover\n4. Press 9,#,1,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
+		"exclusion": "1. Touch keypad with palm\n2. Enter User code in Normal Mode only. Enter Master code if operating Master Mode.\n3. Press 'I' button for Registration from inside the battery cover\n4. Press 9,#,3,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
+		"reset": "1. Touch keypad with palm\n2. Enter User code in Normal Mode only. Enter Master code if operating Master Mode.\n3. Press 'I' button for Registration from inside the battery cover\n4. Press 9,#,9,# on the keypad in sequence\n5. Press 'I' button after 'Ding dong dang' melody plays",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3449/YDM4109Plus_Quick%20Start%20Guide_190702.pdf"
 	}
 }

package/config/devices/0x0129/yrc216-zw3.json

@@ -59,6 +59,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc226-zw3.json

@@ -63,6 +63,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc256-zw3.json

@@ -63,6 +63,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc622-zw3.json

@@ -70,6 +70,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc642-zw3.json

@@ -70,6 +70,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc652-zw3.json

@@ -62,6 +62,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "When lock is reset to factory defaults all Entry Codes\n(including the Master Entry Code*) are deleted and all\nprogramming features are reset to original default\nsettings (see below).\n1. Remove battery cover and batteries.\n2. Remove inside lock to access reset button.\n3. Reset button (see image at right) is located beside\ncable adapter.\n4. While pressing reset button reinstall batteries. Hold\nreset button a minimum of 3 seconds then release.\n5. Replace battery cover.\nAfter reset, Master Entry Code creation is the only\noption available and must be performed prior to\nany other programming of the lock"
+		"reset": "1. Remove battery cover and batteries\n2. Remove inside lock to access reset button\n3. Reset button is located beside cable adapter\n4. While pressing reset button reinstall batteries\n5. Hold reset button a minimum of 3 seconds then release\n6. Replace battery cover"
 	}
 }

package/config/devices/0x0129/yrc_yrd_226_246_256_446-zw2.json

@@ -115,15 +115,18 @@
 			"User Code": [
 				{
 					"method": "getUsersCount",
-					"result": 251
+					"result": 251,
+					"persistValues": {
+						"supportedUsers": 251
+					}
 				}
 			]
 		}
 	},
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 master Pin code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 1 key followed by the gear key",
+		"exclusion": "1. Enter the 4-8 digit master pin code followed by the gear key\n2. Press the 7 key followed by the gear key\n3. Press the 3 key followed by the gear key",
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1878/WGA6ZWManual.pdf"
 	}
 }

package/config/devices/0x0129/yrd136.json

@@ -53,9 +53,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3446/YRD136%20FINAL-compressed%20(1).pdf"
 	}
 }

package/config/devices/0x0129/yrd156.json

@@ -57,9 +57,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Remove the battery cover.\n2. Press and hold reset/pair button on left side of device until unit beeps two (2) times.\n3. Release button and network inclusion begins.\n4. Replace battery cover.",
-		"exclusion": "1. Remove the battery cover.\n2. Press and hold reset/pair button on left side of device until unit beeps five (5) times.\n3. Release button and network exclusion begins.\n4. Replace battery cover.",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the battery cover.\n2. Remove four (4) AA batteries.\n3. On the left side of the device, push and hold the Reset Button with the lever removal tool for at least 3 seconds.\n4. While continuing to hold the reset button, reinstall the batteries\n5. Release reset button and wait 15 seconds.\n6. Reinstall battery cover",
+		"inclusion": "1. Remove the battery cover.\n2. Press and hold reset/pair button on left side of device until unit beeps two (2) times.\n3. Release button.\n4. Replace battery cover.",
+		"exclusion": "1. Remove the battery cover.\n2. Press and hold reset/pair button on left side of device until unit beeps five (5) times.\n3. Release button.\n4. Replace battery cover.",
+		"reset": "1. Remove the battery cover.\n2. Remove four (4) AA batteries.\n3. On the left side of the device, push and hold the Reset Button with the lever removal tool for at least 3 seconds.\n4. While continuing to hold the reset button, reinstall the batteries.\n5. Release reset button.\n6. Reinstall battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3170/YRD156_YaleRealLivingAssureDeadbolt_Z-WavePlus_SystemIntegratorsGuide.pdf"
 	}
 }

package/config/devices/0x0129/yrd216-zw2.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1971/WGA6ZWManual.pdf"
 	}
 }

package/config/devices/0x0129/yrd216-zw3.json

@@ -59,6 +59,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries.\n5. Release reset button.\n6. Replace battery cover."
 	}
 }

package/config/devices/0x0129/yrd226-zw3.json

@@ -63,6 +63,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries.\n5. Release reset button.\n6. Replace battery cover."
 	}
 }

package/config/devices/0x0129/yrd256-zw3.json

@@ -68,6 +68,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries\n2. Remove the interior escutcheon to access the reset button\n3. The reset button is located above the PCB cable connector\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries\n5. Release reset button\n6. Replace battery cover"
 	}
 }