@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x0109/zp3111-5.json

@@ -131,10 +131,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the ZP3111 to the Z-Wave network (inclusion), place the Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds.",
-		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
-		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
-		"wakeup": "Press the Programm Switch once.",
+		"inclusion": "Press the program switch once.",
+		"exclusion": "Press the program switch once.",
+		"reset": "1. Remove cover to trigger tamper switch.\n2. Press program switch 10 times within 10 seconds.",
+		"wakeup": "Press the program switch once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2479/ZP3111-5_R2_20170316.pdf"
 	}
 }

package/config/devices/0x0109/zp3113-7.json

@@ -118,9 +118,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: To add the ZP3113 to your Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3113 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3113 will go to sleep after 30 seconds. The LED indicator will be flashing while the inclusion is continued",
-		"exclusion": "For 'Exclusion' from (removing from) a network: To remove the ZP3113 from your Z-Wave network (exclusion), place your Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3113 to your controller. Press the Program Switch of ZP3113 once to be excluded.",
-		"reset": "Factory Default Reset: \nRemove cover to triggered tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3113 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch once. The LED indicator will flash during inclusion.",
+		"exclusion": "Press the program switch once.",
+		"reset": "1. Remove cover to trigger tamper switch.\n2. Press program switch 10 times within 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4314/ZP3113-7%204%20in%201%20PIR%20(Z-Wave%20certified)%20-%2020211004.pdf"
 	}
 }

package/config/devices/0x0109/zr1202.json

@@ -25,9 +25,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode and following its instruction to add the ZR1202 to your controller. To get into the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the ZR1202 three times in 3 seconds. The LED should stop flashing, if not, please try again.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZR1202 from your controller. Press the program switch on the ZR1202 three times in 3 seconds to be excluded.\nNote: LED setting light will flash continuously in Exclusion condition.",
-		"reset": "Press Program Switch for 5 seconds, the ZR1202 will reset back to factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch three times within 3 seconds. The LED should stop flashing if successful.",
+		"exclusion": "Press the program switch three times within 3 seconds. The LED will flash continuously if successful.",
+		"reset": "Press the program switch for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1325/ZR1202-5%20Repeater.pdf"
 	}
 }

package/config/devices/0x0109/zs5101us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS 5101-5 to your controller. To get in the 'inclusion' mode, please press the program switch of ZS 5101-5 for 1 second at least to be included. The LED on the ZS 5101-5 should go off, if not, please try again",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS 5101-5 from your controller. Press the program switch of ZS 5101-5 for 1 second at least to be excluded.",
-		"reset": "*Push the Tamper switch then power on (put in the battery) & hold the Tamper switch for 5 seconds, ZD5101-5 will send the 'Device Reset Locally Notification' command and reset to the factory default, LED will solid on, need to take off the battery and re-put in the battery to complete the function.\n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Push the tamper switch\n2. Insert the battery while holding the tamper switch\n3. Hold the tamper switch for 5 seconds\n4. Remove and reinsert the battery to complete the reset\n\nThe LED will turn solid on during the reset process.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2099/ZS%205101-5_V1_20160427.pdf"
 	}
 }

package/config/devices/0x0109/zs6101.json

@@ -26,8 +26,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6101-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6101-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6101-5 from your controller. Press the program switch of ZS6101-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second. The red LED will flash continuously if successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1085/ZS%206101-5_ZS6102-5%20%20Smoke%20Detector.pdf"
 	}
 }

package/config/devices/0x0109/zs6102eu-5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6102-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6102-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6102-5 from your controller. Press the program switch of ZS6102-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
-		"reset": "ZS6102-5 will reset back to the factory default value after being excluded from the network.",
+		"inclusion": "Press the program switch for at least 1 second. The LED should go off if successful.",
+		"exclusion": "Press the program switch for at least 1 second. The red LED will flash continuously if successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1084/ZS%206101-5_ZS6102-5%20%20Smoke.pdf"
 	}
 }

package/config/devices/0x0109/zs6301-5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6301-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. By power on to get included for first time or press the test switch of ZS6301-5 once to be included. After be included, the red LED will go on",
-		"exclusion": "For 'Exclusion' from (removing from) a net work: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6301-5 from your controller. Press the test switch of ZS6301-5 once to be excluded.",
-		"reset": "N/A",
+		"inclusion": "Press the test switch once. The red LED will turn on if successful.",
+		"exclusion": "Press the test switch once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1328/ZS6301-5%20CO%20Detector.pdf"
 	}
 }

package/config/devices/0x0109/zt1101.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send 'Device Reset Locally Notification' command and reset to the factory default. (Red LED flashes fast means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
+		"reset": "Press all 4 buttons together for 10 seconds. The LED will turn red for 2 seconds, then green for 2 seconds. A fast flashing red LED indicates reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1706/ZT1101-5%20Keyfob_R1_20150703.pdf"
 	}
 }

package/config/devices/0x0109/zt1141eu-5.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red then turn green. (Green LED flashes 5 times quickly that means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
+		"reset": "Press all 4 buttons together for 10 seconds. The LED will turn red then green. A green LED flashing 5 times quickly indicates reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1709/ZT1141-5%20Wall%20Remote.pdf"
 	}
 }

package/config/devices/0x0109/zw4111eu-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "3. For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode, and following its instruction to add the ZW4111 to your controller. To get in the 'inclusion' mode, press the program switch 3 times or outer switch 1 / switch 2 to be included. \nNOTE: The red LED will flash if ZW4111 has not been included before or the red LED will be OFF.",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZW 4101 / ZW4111 from your controller. Press the program switch or outer switch 1 / switch 2 3 times to be excluded",
-		"reset": "Press Program Switch and power on till 5 seconds, ZW4111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch 3 times or press switch 1 or switch 2. The red LED will be off if successful.",
+		"exclusion": "Press the program switch 3 times or press switch 1 or switch 2 three times.",
+		"reset": "Press the program switch and power on, holding for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1582/ZW%204111-5%20Curtain%20(Screw%20Terminal)%2020151124.pdf"
 	}
 }

package/config/devices/0x010a/vitrum_i_dimmer.json

@@ -27,8 +27,8 @@
 	},
 	"metadata": {
 		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
-		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_i_switch.json

@@ -26,8 +26,8 @@
 	},
 	"metadata": {
 		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
-		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_ii_dimmer.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_ii_switch.json

@@ -29,9 +29,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_iii_eu_dimmer.json

@@ -28,9 +28,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_i.json

@@ -20,9 +20,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_iv.json

@@ -32,9 +32,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_vi.json

@@ -41,8 +41,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
-		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
-		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset."
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red 3 times and sound a tone when successfully excluded.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden factory reset button for at least 3 seconds.\n3. LED will flash red 3 times and sound a tone when reset is complete."
 	}
 }

package/config/devices/0x010b/dn3g6ja069.json

@@ -119,8 +119,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2852/UsersGuide%20DN3G6JA069%20rev1.pdf"
 	}

package/config/devices/0x010b/dn3g6ja082.json

@@ -35,8 +35,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2979/UsersGuide%20DN3G6JA082%20rev1.pdf"
 	}

package/config/devices/0x010b/dn3g6ja084.json

@@ -35,8 +35,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
-		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when completed.",
 		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2980/UsersGuide%20DN3G6JA084%20rev1.pdf"
 	}

package/config/devices/0x010e/danalock_v3-btze.json

@@ -106,9 +106,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Push the switch once. Wait 5 seconds",
-		"exclusion": "Push the switch once. Wait 5 seconds",
-		"reset": "Push the switch ten times",
+		"inclusion": "Push the switch once.",
+		"exclusion": "Push the switch once.",
+		"reset": "Push the switch ten times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4295/Danalock_V3_Product_manual_Z_Wave_V_0.9.5.pdf"
 	}
 }

package/config/devices/0x010f/fgbs222.json

@@ -398,8 +398,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful adding will be confirmed by the LED indicator.",
-		"exclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful removing will be confirmed by the LED indicator.",
+		"inclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.",
+		"exclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.",
 		"reset": "1. Press and hold the button to enter the menu.\n2. Release button when the device glows yellow.\n3. Quickly click the button to confirm.\n4. After few seconds the device will be restarted, which is signalled with the red colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4153/FGBS-222-T-EN-1.2.pdf"
 	}

package/config/devices/0x010f/fgpb101.json

@@ -449,8 +449,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
-		"exclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
+		"inclusion": "Click the Button at least six times.",
+		"exclusion": "Click the Button at least six times.",
 		"reset": "1. Click the Button exactly five times.\n2. Press and hold the Button for at least 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3486/tech_panic_en_9.pdf"
 	}

package/config/devices/0x010f/fgr-224.json

@@ -257,8 +257,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times.\n4. LED indicator will blink yellow.\n5. Successful adding will be confirmed by the device's LED indicator: Green (non-secure, S0, S2 non-authenticated), Magenta (Security S2 Authenticated), Red (not successful).",
-		"exclusion": "1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device.\n4. Successful removing will be confirmed by the device's LED indicator - Red.",
+		"inclusion": "1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times.\n4. LED indicator will blink yellow.\n5. LED indicator will show: Green (non-secure, S0, S2 non-authenticated), Magenta (Security S2 Authenticated), Red (not successful).",
+		"exclusion": "1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device.\n4. LED indicator will turn red if unsuccessful.",
 		"reset": "1. Switch off the mains voltage (disable the fuse).\n2. Remove the device from the wall switch box.\n3. Switch on the mains voltage.\n4. Press and hold the PROG button to enter the menu.\n5. Wait for the LED indicator to glow yellow.\n6. Quickly release and click the PROG button again.\n7. During the factory reset, the LED indicator will blink yellow.\n8. After few seconds the device will be restarted, which is signalled with the red LED indicator colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/948/FGR-224-T-EN-v1.22.pdf"
 	}

package/config/devices/0x010f/fgwp102.json

@@ -158,7 +158,7 @@
 		{
 			"#": "20",
 			"$if": "firmwareVersion >= 3.2",
-			"label": "On/Off (Button)' Association Group (2)",
+			"label": "On/Off (Button) - Association Group (2)",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,
@@ -229,7 +229,7 @@
 		{
 			"#": "24",
 			"$if": "firmwareVersion >= 3.2",
-			"label": "SWITCH ON Value - „On/Off' Association Groups",
+			"label": "SWITCH ON Value - 'On/Off' Association Groups",
 			"valueSize": 2,
 			"minValue": 0,
 			"maxValue": 255,

package/config/devices/0x0123/ne-ssen.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Push \"Add/Remove Button\" of this equipment for a short time.\nAlso, if this equipment is NOT Added to any network, it is enable to Add automatically when the battery is connected",
-		"exclusion": "Push \"Add/Remove Button\" of this equipment for a short time",
-		"reset": "Push and hold \"Add/Remove Button\" for a few seconds more than 5 seconds.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Push the Add/Remove button for a short time.",
+		"exclusion": "Push the Add/Remove button for a short time.",
+		"reset": "Push and hold the Add/Remove button for more than 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2177/NE-SSEN_user_manual_ref2.pdf"
 	}
 }

package/config/devices/0x0123/smart-bridge_c3.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Hold down the hardware INIT SW (over 3 seconds). A button on the GUI is present to start the reset(\"Resets the Chip\" button).\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Hold down the hardware INIT switch for over 3 seconds. Press 'Reset the Chip' in the GUI.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2581/InstructionManual_3GGW_20170925.pdf"
 	}
 }

package/config/devices/0x0123/smart-bridge_cl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Hold down the hardware INIT SW (over 3 seconds). A button on the GUI is present to start the reset(\"Resets the Chip\" button).\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Hold down the hardware INIT switch for over 3 seconds. Press 'Reset the Chip' in the GUI.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2579/InstructionManual_LANGW_20170925.pdf"
 	}
 }

package/config/devices/0x0127/738zpl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "The 738Zplus can perform a Factory Default Reset by initializing defaults in the panel programming menu. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Perform a Factory Default Reset by initializing defaults in the panel programming menu.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2636/LT-1608%20zwave%20certification.pdf"
 	}
 }

package/config/devices/0x0127/xtlpl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use the initialize defaults function to set a panel's programmed memory back to the factory defaults and remove any existing Z-Wave programming. Follow these steps to initialize a panel's defaults:\n1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2685/XTLplus%20zwave%20certification.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrc612-zw3.json

@@ -58,6 +58,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "When lock is reset to factory defaults all Entry Codes\n(including the Master Entry Code*) are deleted and all\nprogramming features are reset to original default\nsettings (see below).\n1. Remove battery cover and batteries.\n2. Remove inside lock to access reset button.\n3. Reset button (see image at right) is located beside\ncable adapter.\n4. While pressing reset button reinstall batteries. Hold\nreset button a minimum of 3 seconds then release.\n5. Replace battery cover.\nAfter reset, Master Entry Code creation is the only\noption available and must be performed prior to\nany other programming of the lock"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the inside lock to access the reset button.\n3. The reset button is located beside the cable adapter.\n4. While pressing the reset button, reinstall the batteries. Hold the reset button for a minimum of 3 seconds, then release.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrc622-zw3.json

@@ -62,6 +62,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrd612-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\n5. Replace battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4644/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrd612-zw3.json

@@ -63,6 +63,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "When lock is reset to factory defaults all Entry Codes\n(including the Master Entry Code*) are deleted and all\nprogramming features are reset to original default\nsettings (see below).\n1. Remove battery cover and batteries.\n2. Remove inside lock to access reset button.\n3. Reset button (see image at right) is located beside\ncable adapter.\n4. While pressing reset button reinstall batteries. Hold\nreset button a minimum of 3 seconds then release.\n5. Replace battery cover.\nAfter reset, Master Entry Code creation is the only\noption available and must be performed prior to\nany other programming of the lock"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the inside lock to access the reset button.\n3. The reset button is located beside the cable adapter.\n4. While pressing the reset button, reinstall the batteries. Hold the reset button for a minimum of 3 seconds, then release.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/nf-yrd622-zw2.json

@@ -77,9 +77,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Enter the 4-8 master Pin code followed by the gear key.\nPress the 7 key followed by the gear key\nPress the 1 key followed by the gear key",
-		"exclusion": "Enter the 4-8 digit master pin code followed by the gear key\nPress the 7 key followed by the gear key\nPress the 3 key followed by the gear key",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master pin code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4645/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/nf-yrd622-zw3.json

@@ -62,6 +62,6 @@
 	],
 	"metadata": {
 		"$import": "templates/yale_template.json#assure_zw3_metadata",
-		"reset": "Remove the battery cover and batteries.\nRemove the interior escutcheon to access the reset button.\nThe reset button is located above the PCB cable connector.\nWhile pressing the reset button for a minimum of 3 seconds, reinstall batteries. Release reset button.\nReplace battery cover. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"reset": "1. Remove the battery cover and batteries.\n2. Remove the interior escutcheon to access the reset button.\n3. The reset button is located above the PCB cable connector.\n4. While pressing the reset button for a minimum of 3 seconds, reinstall the batteries. Release the reset button.\n5. Replace the battery cover."
 	}
 }

package/config/devices/0x0129/ntb610.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1970/nexTouch%20TS%20Manual%20for%20Cert.pdf"
 	}
 }

package/config/devices/0x0129/ntb612-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4643/Binder1.pdf"
 	}
 }

package/config/devices/0x0129/ntb620.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1857/nexTouch%20TS%20Manual%20for%20Cert.pdf"
 	}
 }

package/config/devices/0x0129/ntb622-zw2.json

@@ -76,9 +76,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key",
-		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four (4) AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries \n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing the press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery\n10. Release reset button and wait 15 seconds. Speaker will announce \"Welcome to Yale\"\n11. Reassemble escutcheon",
+		"inclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 1 key followed by the gear key.",
+		"exclusion": "1. Enter the 4-8 digit master PIN code followed by the gear key.\n2. Press the 7 key followed by the gear key.\n3. Press the 3 key followed by the gear key.",
+		"reset": "1. Remove the inside lever with the lever removal tool.\n2. Remove battery cover using hex wrench provided with lock.\n3. Remove four AA batteries.\n4. Remove the 10-32 x 3/4\" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.\n5. Remove inside escutcheon. Cables may stay connected.\n6. Reinstall batteries.\n7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.\n8. While continuing to press the reset button, temporarily remove one AA battery.\n9. Reinstall the battery.\n10. Release reset button. Speaker will announce \"Welcome to Yale\".\n11. Reassemble escutcheon.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4661/Binder1.pdf"
 	}
 }