@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x023b/f4-zb-zwe.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Factory resets the Z-Wave controller.\n1. Open gateway settings in your Web App and press 'Reset' (Z-Wave Settings)\n2. Confirm the dialog. This will perform a factory reset and remove every Z-Wave device from your Gateway (you have to repair them again).\nNote: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Open gateway settings in your Web App and press 'Reset' (Z-Wave Settings), then confirm the dialog",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2560/User%20Manual%20v2.4.pdf"
 	}
 }

package/config/devices/0x023c/qbbiozw.json

@@ -31,9 +31,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Adding The Quickbox to your Z-Wave network (Inclusion):\n\nPrepare your Z-Wave controller to add a device to the network (refer to your controller's user manual.) Push the Z-Wave button on The Quickbox",
-		"exclusion": "Removing The Quickbox from your Z-Wave network (Exclusion):\n\nPrepare your Z-Wave controller to remove a device from the network (refer to your controller's user manual) Push the Z-Wave button on The Quickbox",
-		"reset": "Manual Reset:\nTo reset The Quickbox Z-Wave settings to its factory defaults, hold the Z-Wave button for 5 seconds. Use the reset procedure only when the primary controller is missing or inoperable.",
+		"inclusion": "Push the Z-Wave button on The Quickbox.",
+		"exclusion": "Push the Z-Wave button on The Quickbox.",
+		"reset": "Hold the Z-Wave button for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1347/Quickbox%20Quickstart%20Guide.pdf"
 	}
 }

package/config/devices/0x023c/qldlzw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Prepare your Z-Wave controller to add a device to the network (refer to your controller's user manual.) Push the Z-Wave button on The Doorlock. The button is accessed through a small hole, insert a paperclip or similar to push it. (See diagram in Product Manual for button placement.)",
-		"exclusion": "Prepare your Z-Wave controller to remove a device from the network (refer to your controller's user manual)\nPush the Z-Wave button on The Doorlock. (See diagram in Product Manual for button placement.)",
-		"reset": "To reset The Doorlock's Z-Wave settings to their factory defaults, hold the Z-Wave button down for 5 seconds. (See diagram in Product Manual for button placement.) The reset procedure should only be used when the primary controller is missing or inoperable",
+		"inclusion": "Push the Z-Wave button on The Doorlock.",
+		"exclusion": "Push the Z-Wave button on The Doorlock.",
+		"reset": "Hold the Z-Wave button down for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1451/R003023_02-Doorlock%20Operating%20Instructions.pdf"
 	}
 }

package/config/devices/0x023d/dch-01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This must be done when the DoorCam is in an excluded status, which means that it is not a part of any Z-Wave network; you will know this because the Z-Wave LED will remain on.\nAfter starting the inclusion process on your Z-Wave controller, please do the following:\na. Press & hold the Z-Wave inclusion button for 5 seconds.\nb. When the Z-Wave LED blinks rapidly, release the Z-Wave inclusion button.\nc. The DoorCam will try inclusion for 30 seconds.\nd. If inclusion was successful, the Z-Wave LED will turn off",
-		"exclusion": "This must be done when the DoorCam is in an included status, which means that it is a part of any Z-Wave network; you will know this because the Z-Wave LED will remain off.\nAfter starting the exclusion process on your Z-Wave Controller, please do the following.\na. Press & hold ‘Z-Wave' button for 5 seconds when DoorCam is inclusion status.\nb. When Z-Wave LED blinks with 250ms interval, Release ‘Z-Wave' button to try exclusion.\nc. DoorCam will try exclusion for 30sec.\nd. Z-Wave LED will be turned on if exclusion is successful",
-		"reset": "a. Hold the ‘Z-Wave' button for 10 seconds.\n(Z-Wave LED will blink after 5 seconds with 250ms interval then Z-Wave LED will be turned off after another 5 seconds.) \nb. When Z-Wave LED stops blinking after 10 seconds, release Z-Wave button.\nc. When factory reset is successful, LED will be on.\n\nPlease use this procedure only if the network primary controller is missing or inoperable",
+		"inclusion": "1. Press & hold the Z-Wave inclusion button for 5 seconds.\n2. When the Z-Wave LED blinks rapidly, release the Z-Wave inclusion button.\n3. The DoorCam will try inclusion for 30 seconds.\n4. If inclusion was successful, the Z-Wave LED will turn off.",
+		"exclusion": "1. Press & hold 'Z-Wave' button for 5 seconds.\n2. When Z-Wave LED blinks with 250ms interval, release 'Z-Wave' button.\n3. DoorCam will try exclusion for 30sec.\n4. Z-Wave LED will be turned on if exclusion is successful.",
+		"reset": "1. Hold the 'Z-Wave' button for 10 seconds.\n2. When Z-Wave LED stops blinking after 10 seconds, release Z-Wave button.\n3. When factory reset is successful, LED will be on.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2457/IoT%20DoorCam_Manual_r03.pdf"
 	}
 }

package/config/devices/0x023f/ca-1_c4-zwu.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Launch Composer. Click on the Z-Wave Configuration tab in the project properties window.\n\n2. Click on \"Reset Defaults\". This clears the Home ID on the Z-Wave controller and abandons any nodes on the existing network. Any Z-Wave devices previously joined to the network must be removed before they can join the new network.",
+		"reset": "Launch Composer and click on the Z-Wave Configuration tab in the project properties window, then click on \"Reset Defaults\"",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2383/DOC-00228-B%20Z-Wave%20Setup%20Guide.pdf"
 	}
 }

package/config/devices/0x023f/ea-1_c4-zwu.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Launch Composer. Click on the Z-Wave Configuration tab in the project properties window.\n\n2. Click on \"Reset Defaults\". This clears the Home ID on the Z-Wave controller and abandons any nodes on the existing network. Any Z-Wave devices previously joined to the network must be removed before they can join the new network.",
+		"reset": "Launch Composer and click on the Z-Wave Configuration tab in the project properties window, then click on \"Reset Defaults\"",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2452/DOC-00228-B%20Z-Wave%20Setup%20Guide.pdf"
 	}
 }

package/config/devices/0x023f/ea-3_c4-zwu.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Launch Composer. Click on the Z-Wave Configuration tab in the project properties window.\n\n2. Click on \"Reset Defaults\". This clears the Home ID on the Z-Wave controller and abandons any nodes on the existing network. Any Z-Wave devices previously joined to the network must be removed before they can join the new network.",
+		"reset": "Launch Composer and click on the Z-Wave Configuration tab in the project properties window, then click on \"Reset Defaults\"",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2455/DOC-00228-B%20Z-Wave%20Setup%20Guide.pdf"
 	}
 }

package/config/devices/0x023f/ea-5_c4-zwu.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Launch Composer. Click on the Z-Wave Configuration tab in the project properties window.\n\n2. Click on \"Reset Defaults\". This clears the Home ID on the Z-Wave controller and abandons any nodes on the existing network. Any Z-Wave devices previously joined to the network must be removed before they can join the new network.",
+		"reset": "Launch Composer and click on the Z-Wave Configuration tab in the project properties window, then click on \"Reset Defaults\"",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2447/DOC-00228-B%20Z-Wave%20Setup%20Guide.pdf"
 	}
 }

package/config/devices/0x0241/6336-brain-00008.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this cont- roller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Open the settings\n2. Click on „NEEO Brain'\n3. Click on „Remove all data (reset)' and follow the instructions",
+		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this cont- roller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n1. Open the settings\n2. Click on 'NEEO Brain'\n3. Click on 'Remove all data (reset)' and follow the instructions",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2349/NEEO_ZWave-User-Documentation_final_V4.pdf"
 	}
 }

package/config/devices/0x0242/03110101.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "A. Press Button switch 3 times in a row to link device to Z-Wave network or remove device from Z-Wave network. \nB. Press Button switch 3 times in a row again to cancel to link device to Z-Wave network.",
-		"exclusion": "A. Acknowledge of Green LED lightning. \nB. Press Button switch 3 times in a row to link device to Z-Wave network or remove device from Z-Wave network.",
-		"reset": "A. Press Fn switch over 2minutes to initialize connecting network information. \nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the button switch 3 times in a row. Press 3 times again to cancel inclusion",
+		"exclusion": "1. Wait for green LED to light\n2. Press the button switch 3 times in a row",
+		"reset": "Press the Fn switch for over 2 minutes to reset network information",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1664/Repeater_Q_160205.pdf"
 	}
 }

package/config/devices/0x024a/heimdall.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Click 'Reset', show 'Processing…' to reset the Z-Wave network. Refer user manual page 12",
+		"reset": "Click 'Reset' and wait for 'Processing…' to appear.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1832/UM-Heimdall-SUNITEC-en160714.pdf"
 	}
 }

package/config/devices/0x024b/1015.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "You can login the WEB of LS1015 to set the product to the factory default state. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Login to the web interface to reset the product to factory default state.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1877/31507632-Smart%20Home%20Gateway%20LS1015%20Quick%20Start%2002.pdf"
 	}
 }

package/config/devices/0x024c/ht-a10.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "This must be done at GAS valve and when closed. Press Timer UP button for 5 seconds till hearing beep once",
-		"exclusion": "This must be done at GAS valve and when closed. Press Timer UP button for 5 seconds till hearing beep once",
-		"reset": "This must be done at GAS valve and when closed. Press Timer UP button for 10 seconds till hearing beep once. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Close the gas valve and press the Timer UP button for 5 seconds until you hear one beep.",
+		"exclusion": "Close the gas valve and press the Timer UP button for 5 seconds until you hear one beep.",
+		"reset": "Close the gas valve and press the Timer UP button for 10 seconds until you hear one beep.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1687/Manual_soosanhometech.pdf"
 	}
 }

package/config/devices/0x024c/ht-a20.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Press On/OFF button for 5 seconds till hearing beep once.\nWhen inclusion completes, you will hear ‘beep' sound with voice message alert. When inclusion completes, Connection LED will be on.",
-		"exclusion": "Press On/OFF button for 5 seconds till hearing beep once.\nWhen exclusion completes, you will hear ‘beep' sound with voice message alert. When exclusion completes, Connection LED will be off. (The same as the inclusion method)",
-		"reset": "Press On/OFF button for 10 seconds till hearing beep once.\n When reset completes, you will hear ‘beep' sound with voice message alert.\n(Reset function, the primary controller will be used only when does not exist or inoperative.)",
+		"inclusion": "Press the On/Off button for 5 seconds until you hear one beep. When inclusion completes, you will hear a 'beep' sound with voice message alert and the Connection LED will turn on.",
+		"exclusion": "Press the On/Off button for 5 seconds until you hear one beep. When exclusion completes, you will hear a 'beep' sound with voice message alert and the Connection LED will turn off.",
+		"reset": "Press the On/Off button for 10 seconds until you hear one beep. When reset completes, you will hear a 'beep' sound with voice message alert.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1884/Product%20Manual.pdf"
 	}
 }

package/config/devices/0x024d/dn3g6ja062.json

@@ -51,9 +51,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Using a paper clip or equivalent, push the button over 3 seconds.\n(Please note that this product is reset if switch is pushed over 10 seconds)\nStatus LED turns off after adding",
-		"exclusion": "Using a paper clip or equivalent, push the button over 3 seconds.\n(Please note that this product is reset if switch is pushed over 10 seconds)\nStatus LED starts flashing after removal is finished",
-		"reset": "Using a paper clip or equivalent, push the button over 10 seconds.\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Using a paper clip, push the button for over 3 seconds. The status LED turns off after successful inclusion.",
+		"exclusion": "Using a paper clip, push the button for over 3 seconds. The status LED starts flashing after successful removal.",
+		"reset": "Using a paper clip, push the button for over 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1651/User's%20Guide%20151215_160310_updated.pdf"
 	}
 }

package/config/devices/0x024d/zg-500-v1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "The reset can be done through the hardware button. A long single click (over 10 seconds) will trigger the reset. A button on the GUI is also present to start the reset (\"Resets the Chip\").\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold the hardware button for over 10 seconds to trigger the reset. You can also use the GUI button labeled \"Resets the Chip\".",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1667/InstructionManual_v4.pdf"
 	}
 }

package/config/devices/0x024d/zg-501-v1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Hold down the hardware button (over 10 seconds). This will reset the Z-Wave chip and Z-Wave LED blinks 5 times quickly. Upon reset, the hardware will broadcast the 'DEVICE RESET LOCALLY NOTIFICATION'. Reset cannot be aborted.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Hold down the hardware button for over 10 seconds. The Z-Wave LED will blink 5 times quickly when reset is successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2207/InstructionManual_3GGW_20170209.pdf"
 	}
 }

package/config/devices/0x024f/ad1-10v.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted, and will disable remote control of the device. The device will have to be re-added to the Z-Wave network and reconfigured afterwards, to regain the previous operation of the device. Please DO NOT execute this procedure unless it is absolutely necessary.\n\nPush and Hold the Add/Remove button for about 15 seconds – until the LED indicator turns OFF. Then release the button. The device is now Factory Reset, and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
+		"inclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"exclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"reset": "Push and hold the button in the button hole for about 15 seconds using a paperclip until the LED indicator turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2857/AMD_AD1-10V%20-%20Standalone%20Z-Wave%20Dimmer%20-%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x024f/am.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted, and will disable remote control of the device. The device will have to be re-added to the Z-Wave network and reconfigured afterwards, to regain the previous operation of the device. Please DO NOT execute this procedure unless it is absolutely necessary.\n\nPush and Hold the Add/Remove button for about 15 seconds – until the LED indicator turns OFF. Then release the button. The device is now Factory Reset, and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
+		"inclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"exclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"reset": "Push and hold the button in the button hole for about 15 seconds using a paperclip until the LED indicator turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2856/AMD_AD1-10V%20-%20Standalone%20Z-Wave%20Dimmer%20-%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x024f/ar1p.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted and WILL remove it from the Z-Wave network. Please DO NOT execute this procedure unless it's absolutely necessary.\n\nPress and Hold the Add/Remove button for about 15 seconds - until LED indicator starts blinking. Then release the button. The device will now be factory reset and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
+		"inclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"exclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"reset": "Push and hold the button in the button hole for about 15 seconds using a paperclip until the LED indicator starts blinking.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2858/ARxP%20-%20Standalone%20Z-Wave%20Relay%20-%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x024f/ar2p.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
-		"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted and WILL remove it from the Z-Wave network. Please DO NOT execute this procedure unless it's absolutely necessary.\n\nPress and Hold the Add/Remove button for about 15 seconds - until LED indicator starts blinking. Then release the button. The device will now be factory reset and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
+		"inclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"exclusion": "Push and hold the button in the button hole for approximately one second using a paperclip. The device LED will blink twice.",
+		"reset": "Push and hold the button in the button hole for about 15 seconds using a paperclip until the LED indicator starts blinking.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2859/ARxP%20-%20Standalone%20Z-Wave%20Relay%20-%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x025b/ez0001.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nSteps to Reset eZLO Hub\n1. Sign in to the eZLO app and select the eZLO hub you want your device to connect to.\n2. Select\"Settings\" from the My eZLO menu\n3. Click \"Clean eZLO\" button.\n\nOR\n1. Sign in to the eZLO app and select the eZLO hub you want your device to connect to.\n2. Select\"Devices\" from the My eZLO menu\n3. Select Z-Wave to filter out only Z-Wave devices.\n4. Open the \"Z-Wave Actions\" menu. \n5. Click \"Reset\"",
+		"reset": "1. Sign in to the eZLO app and select the eZLO hub.\n2. Select \"Settings\" from the My eZLO menu.\n3. Click \"Clean eZLO\" button.\n\nAlternatively:\n1. Sign in to the eZLO app and select the eZLO hub.\n2. Select \"Devices\" from the My eZLO menu.\n3. Select Z-Wave to filter out only Z-Wave devices.\n4. Open the \"Z-Wave Actions\" menu.\n5. Click \"Reset\".",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2471/Ezlo_UserGuide_Web_Device_1.0.pdf"
 	}
 }

package/config/devices/0x025b/ezlopl.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector. Push and hold the RESET button for at least 5 sec (on Ezlo Plus LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults. Reset to Factory Settings remove all the information about added devices and reset Z-Wave chip (new Home ID, new S0/S2 keys, remove all Z-Wave nodes), scenes created, House modes settings, etc. The process is irreversible",
+		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector. Push and hold the RESET button for at least 5 seconds. On Ezlo Plus LED starts blinking RED. After that your Ezlo controller will be reset to factory defaults.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4308/Ezlo%20Plus%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x025b/ezlosecure.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector.\nPush and hold the RESET button for at least 5 sec (on Ezlo Secure LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults.\nReset to Factory Settings remove all the information about added devices\nand reset Z-Wave chip (new Home ID, new S0/S2 keys, remove all Z-Wave\nnodes), scenes created, House modes settings, etc. The process is\nirreversible.",
+		"reset": "Find the \"Reset\" button on the controller near the Ethernet cable connector. Push and hold the RESET button for at least 5 seconds. On Ezlo Secure LED starts blinking RED. After that your Ezlo controller will be reset to factory defaults.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4111/Ezlo%20Secure%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x025b/zl-100.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1. Click the gear icon on the left sidebar\n2. Click Reset hub to default.\n3. Click Yes when prompted to confirm, or No if you decide not to reset the ZL-100.\n4. If you confirm the ZL-100 reset request, it returns to its default settings. The My ZLINKs page is displayed.\nThe image of the reset ZL-100 now displays a default name and color.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Click the gear icon on the left sidebar.\n2. Click Reset hub to default.\n3. Click Yes when prompted to confirm, or No if you decide not to reset the ZL-100.\n4. If you confirm the ZL-100 reset request, it returns to its default settings.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3868/New%20Ezlo%20PlugHub%20Product%20Manual%20(1)%20(1).pdf"
 	}
 }

package/config/devices/0x026b/eia650rfz.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To include the device start the inclusion on your controller and then hit the little button on the wireless module for 1 second",
-		"exclusion": "To exclude the device start the inclusion on your controller and then hit the little button on the wireless module for 1 second",
-		"reset": "To reset the device keep the button pushed for 10 seconds. After 5 seconds the led starts flashing and after another 5\nseconds there is a short beep signaling the successful reset back to factory defaults. Use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the button on the wireless module for 1 second.",
+		"exclusion": "Press the button on the wireless module for 1 second.",
+		"reset": "Press and hold the button for 10 seconds. After 5 seconds the LED starts flashing and after another 5 seconds there is a short beep signaling the successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2228/B18579R3SMOKEZWAVEUCUS.pdf"
 	}
 }

package/config/devices/0x026e/brz1.json

@@ -26,7 +26,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Press and hold the button on the control for approximately 15 seconds (the LED will stop flashing when complete.\n\n\n\"Please use this procedure only when the network primary controller is missing or otherwise inoperable.\"",
+		"reset": "Press and hold the button on the control for approximately 15 seconds. The LED will stop flashing when complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1787/Graber%20Virtual%20Cord%20Owner's%20Manual.pdf"
 	},
 	"compat": {

package/config/devices/0x026e/crzb.json

@@ -18,9 +18,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Put Primary Controller into Inclusion Mode\n\n2. Press and Hold Shade Programming Button for 3 seconds (release when LED flashes).\n\n\n\nTo include a shade and shade remote to the Z-Wave network, and pair the remote to the shade you must follow this sequence:\n\n1. Do a shade Z-Wave reset and then include into the Z-Wave network.\n\n2. Do a remote reset and then include the remote into the Z-Wave network.\n\n3. Pair the remote to the shade.",
-		"exclusion": "1. Put Primary Controller into Exclusion Mode\n\n2. Press and Hold Shade Programming Button for 3 seconds (release when LED flashes).",
-		"reset": "Z-Wave Reset:Exclude from the controller before doing this. Press and hold the button on the shade for approximately 10 seconds (release when the shade jogs, holding longer will perform a full reset).\n\nFull Reset: Please use this procedure only when the network primary controller is missing or otherwise inoperable. Press and hold the button on the shade for approximately 15 seconds (the LED will stop flashing when complete) - you will need to set top / bottom / home positions.",
+		"inclusion": "Press and hold the shade programming button for 3 seconds. Release when LED flashes.",
+		"exclusion": "Press and hold the shade programming button for 3 seconds. Release when LED flashes.",
+		"reset": "Z-Wave Reset: Exclude from the controller before doing this. Press and hold the button on the shade for approximately 10 seconds, and release when the shade jogs.\n\nFull Reset: Press and hold the button on the shade for approximately 15 seconds (the LED will stop flashing when complete) - you will need to set top / bottom / home positions.",
 		"manual": "https://support.springswf.net/helpdesk/attachments/30050113378"
 	}
 }

package/config/devices/0x026e/csz1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Put Primary Controller into Inclusion Mode\n\n2. Press and Hold Shade Programming Button for >2seconds",
-		"exclusion": "1. Put Primary Controller into Exclusion Mode\n\n2. Press and Hold Shade Programming Button for >2seconds",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable\n\nPress and hold the button on the shade for approximately 15 seconds (the LED will stop flashing when complete)",
+		"inclusion": "Press and hold the shade programming button for more than 2 seconds.",
+		"exclusion": "Press and hold the shade programming button for more than 2 seconds.",
+		"reset": "Press and hold the button on the shade for approximately 15 seconds. The LED will stop flashing when complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1749/Graber%20Virtual%20Cord%20Owner's%20Manual%200002.pdf"
 	}
 }

package/config/devices/0x026e/mcz1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Restores the remote back to a factory\nstate by removing all memory of shade\nand remote pairings from the remote.\n1. On the remote, press and hold the\nMENU/RIGHT button to enter the menu.\n2. Select ZWAVE > RESET.\n3. With LIKE NEW? selected, press and\nhold the MENU/RIGHT button until the\nscreen no longer tells you to wait.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. On the remote, press and hold the MENU/RIGHT button to enter the menu.\n2. Select ZWAVE > RESET.\n3. With LIKE NEW? selected, press and hold the MENU/RIGHT button until the screen no longer tells you to wait.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2819/P2_79083-01_18-8215_MotorizationManual.pdf"
 	}
 }

package/config/devices/0x026e/vcz1.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "Press and hold the programming button until the LED light bar begins to flash green then release the button.",
 		"exclusion": "Press and hold the programming button until the LED light bar begins to flash green then release the button.",
-		"reset": "Press and hold the programming button until the LEDs stop blinking. LEDs will blink green, amber, red, and then finally turn off (about 15 seconds). Local Reset must be performed on both the controllers and motors and should only be used if the primary controller is no longer available.",
+		"reset": "Press and hold the programming button until the LEDs stop blinking. LEDs will blink green, amber, red, and then finally turn off (about 15 seconds).",
 		"wakeup": "Press and release the programming button one time.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1786/Graber%20Virtual%20Cord%20Owner's%20Manual.pdf"
 	},

package/config/devices/0x026f/zht-630.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "‘ADDING' YOUR Z-WAVE UNITS\nDo not attempt to add your Z-Wave Module unless you are familiar with the operation of your Z-Wave Controller.\n1. Read the instructions for your Z-Wave Controller regarding adding new devices. Then initiate the inclusion function from your Z-Wave Controller.\n2. Triple-press the add button once the Z-Wave Module is on the device. The LED will show a quick blink once per second while the module is being added. This process may take as long as 30 seconds, but typically is much quicker. If you triple-press too quickly or too slowly, inclusion will not start. In this case wait a few seconds and then try again.\n3. Upon successful inclusion, the Z-Wave Module LED will flash 3 times. If inclusion fails, the LED will simply stop its blink pattern.\n4. If inclusion does not succeed, restart at step 1.\n5. If successful, place the alarm on its base and wait at least 30 seconds.\n6. Press the alarm's test button and verify the Z-Wave Controller receives Notification Reports.\n7. After the Z-Wave Module is included, you may define association groups or perform other configuration operations from the Z-Wave Controller.",
-		"exclusion": "‘REMOVING' YOUR Z-WAVE UNITS\n1. Read the instructions on your Z-Wave Controller regarding removing devices. Note that a device can be removed using any Z-Wave Controller, not just the Controller that was used to add the Module. Initiate the removal process at your Controller.\n2. Triple-press the button on the Z-Wave Module. The LED will show a quick double-blink once per second while the module is being removed. This process may take up to 30 seconds. If you triple-press too quickly or too slowly the removing function will not start. In this case you must wait a few seconds and then try again.\n3. Upon successful removal, the Z-Wave Module LED will flash 5 times. If removal fails, the LED will simply stop its blink pattern.\n4. If the removal operation does not succeed, restart at step 1.\n5. After removing, either a) add the Z-Wave Module into a different Z-Wave Controller, or b) remove the battery from the Z-Wave Module.\n\nNOTE: The effective range of the wireless module may be reduced by walls and other obstructions in the building. It is recommended not to exceed 40m as the maximum distance between smoke alarms and the Controller.",
-		"reset": "‘FACTORY RESET' YOUR Z-WAVE UNITS \nThis operation should only be performed if the module is to be excluded from the network and if the Z-Wave Controller is also being reset or removed. \n1. Press and hold the button for 10 seconds. The LED will go off. Now release the button. The LED will flash once as the module resets. \n2. After resetting, either a) include the module into a different Z-Wave Controller, or b) remove the battery from the module to avoid power draining. \n* use the reset procedure only when the primary controller is missing or inoperable.",
+		"inclusion": "1. Triple-press the add button once the Z-Wave module is on the device.\n2. The LED will show a quick blink once per second while the module is being added.\n3. Upon successful inclusion, the Z-Wave module LED will flash 3 times.\n4. If inclusion fails, the LED will simply stop its blink pattern.",
+		"exclusion": "1. Triple-press the button on the Z-Wave module.\n2. The LED will show a quick double-blink once per second while the module is being removed.\n3. Upon successful removal, the Z-Wave module LED will flash 5 times.\n4. If removal fails, the LED will simply stop its blink pattern.",
+		"reset": "1. Press and hold the button for 10 seconds.\n2. The LED will go off, then release the button.\n3. The LED will flash once as the module resets.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2631/50253%20combined%20manuals.pdf"
 	}
 }

package/config/devices/0x027a/templates/zooz_template.json

@@ -1137,8 +1137,8 @@
 		"defaultValue": 1
 	},
 	"zen5x_metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion. \nSCAN THE QR CODE / ENTER THE 5-DIGIT PIN if using the new SmartStart method. The SmartStart security PIN is located on the back of the relay, next to the Z-Wave Plus logo.\n3. The LED indicator will blink green to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the relay if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Click the Z-Wave button on the relay 3 times quickly (the LED indicator will start blinking green)\n4. Your hub will confirm exclusion, the LED indicator on the relay will turn green for 2 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the relay, click the Z-Wave button twice and hold it for 15 seconds. The LED indicator will flash during the process and turn red for 3 seconds to confirm successful reset."
+		"inclusion": "Tap up 3 times quickly. The LED indicator will blink green. It will turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails.",
+		"exclusion": "Click the Z-Wave button 3 times quickly. The LED indicator will start blinking green. It will turn green for 2 seconds when exclusion is successful.",
+		"reset": "Click the Z-Wave button twice and hold it for 15 seconds. The LED indicator will flash during the process and turn red for 3 seconds to confirm successful reset."
 	}
 }

package/config/devices/0x027a/zac03.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Plug the valve control in within 3 feet from your controller.\n2. Put your Z-Wave controller in inclusion mode.\n3. Press the red power button on the valve control THREE times quickly.\n4. A new on-off device should appear on your controller's dashboard",
-		"exclusion": "1. Plug the valve control in within 3 feet from your controller.\n2. Put your Z-Wave controller in exclusion mode.\n3. Press the red power button on the valve control THREE times quickly.\n4. The device should disappear from your controller's dashboard",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, please press and hold the red power button for 10 seconds. The LED indicator on the device will flash to indicate the process has been successfully completed.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "1. Plug the valve control in within 3 feet of your location\n2. Press the red power button on the valve control THREE times quickly\n3. The LED indicator will confirm successful inclusion",
+		"exclusion": "1. Plug the valve control in within 3 feet of your location\n2. Press the red power button on the valve control THREE times quickly\n3. The LED indicator will confirm successful exclusion",
+		"reset": "Press and hold the red power button for 10 seconds. The LED indicator on the device will flash to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1748/zooz-zac03-valve-control-manual.pdf"
 	}
 }

package/config/devices/0x027a/zac36.json

@@ -316,9 +316,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Set your Z-Wave Gateway into Inclusion mode / Add device.\ni. Start: Short press Touch Sense Button 3 times.\nii. Processing: Yellow LED and short beep sound keeping continue. For security inclusion support, you may need to entering first 5 digit\nthat show on QR Code label, please refer to the instructions of central controller.\niii. Success: Green LED on 1 second with 2 short beep sounds.\niv. The LED indication changes to Green LED slow blinking from Yellow LED blinking.",
-		"exclusion": "Set your Z-Wave Gateway into Exclusion mode / Remove device.\ni. Start: Short press Touch Sense Button 3 times.\nii. Processing: Yellow LED and short beep sound keeping continue.\niii. Success: Green LED on 1 second with 2 short beep sounds.\niv. The LED indication Changes to Yellow LED blinking",
-		"reset": "Start: Long hold Touch Sense Button for 10 seconds then short click 5 times.\nii. Processing: Yellow LED ON 1 second then wait 2-5 seconds.\niii. Success: Green LED on 2 second with long beep sounds for 2 seconds.\n*Factory Default Reset will:\na. Remote the BVS from Z-Wave Network;\nb. Delete the association setting;\nc. Restore the configuration settings to the default",
+		"inclusion": "1. Press the Touch Sense Button 3 times quickly\n2. The yellow LED will blink and you'll hear short beeps\n3. When successful, the green LED will turn on for 1 second with 2 short beeps\n4. The LED will then change to slow green blinking",
+		"exclusion": "1. Press the Touch Sense Button 3 times quickly\n2. The yellow LED will blink and you'll hear short beeps\n3. When successful, the green LED will turn on for 1 second with 2 short beeps\n4. The LED will then change to yellow blinking",
+		"reset": "1. Hold the Touch Sense Button for 10 seconds, then click it 5 times quickly\n2. The yellow LED will turn on for 1 second, then wait 2-5 seconds\n3. When successful, the green LED will turn on for 2 seconds with long beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3885/BVS_ZWU_v1.0.9.pdf"
 	}
 }

package/config/devices/0x027a/zen06.json

@@ -127,9 +127,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "There are three types of inclusion for this device: 1) Auto Z-Wave Inclusion 2) Manual Z-Wave Inclusion 3) Secure Z-Wave Inclusion.\n\n1) Auto Z-Wave Inclusion\n1. Put your Z-Wave controller in inclusion mode\n2. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n3. LED indicator will flash blue4. A new on / off device should be recognized by your Z-Wave controller\n\n2)Manual Z-Wave Inclusion\n1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n2. Put your Z-Wave controller in inclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. LED indicator will flash blue\n5. A new on / off device should be recognized by your Z-Wave controller\n\n3)Secure Z-Wave Inclusion\n1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n2. Put your Z-Wave controller in secure inclusion mode\n3. Press and HOLD the Z-Wave button for at least 3 seconds\n4. LED indicator will flash green\n5. LED indicator will turn solid green once the inclusion is completed. Please allow 5 minutes for configuration. DO NOT press any buttons or move the device during that time\n6. A new secure on / off device should be recognized by your Z-Wave controller.",
-		"exclusion": "1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n2. Put your Z-Wave controller in exclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. LED indicator will flash orange\n5. The smart plug should disappear from your controller's device list and LED indicator will remain solid orange for a few seconds to indicate exclusion.",
-		"reset": "Plug the smart plug into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will stay solid yellow for 2 seconds to indicate successful reset. The plug will then automatically turn off. NOTE: All previously recorded activity and custom settings will be erased from the devices memory. You may only reset your smart plug once it has been included to a Z-Wave network.",
+		"inclusion": "Manual inclusion: Press and release the Z-Wave button 3 times quickly (LED indicator will flash blue).\n\nSecure inclusion: Press and hold the Z-Wave button for at least 3 seconds (LED indicator will flash green).",
+		"exclusion": "Press and release the Z-Wave button 3 times quickly. The LED indicator will flash orange then remain solid orange for a few seconds.",
+		"reset": "Press and hold the Z-Wave button for at least 20 seconds. The LED indicator will stay solid yellow for 2 seconds to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=Manuals/1901/Zooz-Z-Wave-Smart-Plug-ZEN06%20Manual.pdf"
 	}
 }

package/config/devices/0x027a/zen14.json

@@ -76,9 +76,9 @@
 		"preserveRootApplicationCCValueIDs": true
 	},
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface).\nWhile the hub is looking for new devices, click the Z-Wave™ button 3 times as quickly as possible. The LED indicator will start flashing blue to confirm inclusion. mode and turn green for 1 second once inclusion is completed.",
-		"exclusion": "1. Bring the plug within direct range of your Z-Wave™ gateway (hub).\n2. Put the Z-Wave™ hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Press and release the Z-Wave™ button 3 times quickly.\n4. Your hub will confirm exclusion and the plug will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the plug is powered, then click the Z-Wave™ button twice and hold it the third time for 10 seconds. The LED indicator will flash green 3 times to confirm a successful reset",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing blue and turn green for 1 second once inclusion is completed.",
+		"exclusion": "1. Press and release the Z-Wave button 3 times quickly\n2. The LED indicator will start flashing\n3. The LED will turn off when exclusion is complete",
+		"reset": "1. Click the Z-Wave button twice\n2. Hold it the third time for 10 seconds\n3. The LED indicator will flash green 3 times to confirm a successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4674/zooz-outdoor-double-plug-zen14-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen15.json

@@ -320,9 +320,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Please include the Power Switch to your network BEFORE connecting it to the appliance you wish to control.\n\nAuto Z-Wave Inclusion:\n1. Put your Z-Wave controller into inclusion mode\n2. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n3. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included\n4. A new on / off device will be recognized by your Z-Wave controller\n\nManual Z-Wave Inclusion:\n1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n2. Put your Z-Wave controller into inclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included\n5. A new on / off device will be recognized by your Z-Wave controller\n\nSecure Z-Wave Inclusion:\n1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n2. Put your Z-Wave controller in secure inclusion mode\nPress and HOLD the Z-Wave button for at least 3 seconds\n3. The LED indicator will start flashing green, then turn blue (on) or pink (off) once included\n4. A new secure on / off device will be recognized by your Z-Wave controller",
-		"exclusion": "1. Plug the Power Switch into a grounded receptacle located within direct range of your Z-Wave gateway controller\n2. Put your Z-Wave controller into exclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. The LED indicator will start flashing orange, then turn blue (on) or pink (off) once excluded\n5. The Power Switch will disappear from your controller's device list. The LED indicator will remain solid orange for a few seconds to indicate exclusion\n\nIf the first attempt is unsuccessful, please repeat the process following all steps carefully",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the Power Switch into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset. The Power Switch will then turn off.\n\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory. You may only reset your Power Switch once it has been included to a Z-Wave network",
+		"inclusion": "Press and release the Z-Wave button 3 times quickly. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included.",
+		"exclusion": "Press and release the Z-Wave button 3 times quickly. The LED indicator will start flashing orange, then turn blue (on) or pink (off) once excluded.",
+		"reset": "Press and hold the Z-Wave button for at least 20 seconds. The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2517/zooz-z-wave-plus-power-switch-zen15-user-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen17.json

@@ -536,9 +536,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "INCLUSION\n1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
-		"exclusion": "1. Bring your Universal Relay close to the Z-Wave hub and power it\n2. Put the Z-Wave hub into exclusion mode\n3. Click the Z-Wave button 3 times quickly\n4. Your hub will confirm exclusion and the Universal Relay will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, click the Z-Wave button 4 times quickly, the LED indicator will light up,\nthen quickly click the Z-Wave button 4 times again. The LED indicator will flash 3 times to confirm successful reset and will then turn off",
+		"inclusion": "Tap the Z-Wave button 3 times quickly. The LED indicator will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "1. Click the Z-Wave button 3 times quickly\n2. The LED indicator will blink\n3. The LED will turn off when exclusion is complete",
+		"reset": "1. Click the Z-Wave button 4 times quickly\n2. The LED indicator will light up\n3. Quickly click the Z-Wave button 4 times again\n4. The LED indicator will flash 3 times to confirm successful reset and will then turn off",
 		"manual": [
 			{
 				"$if": "firmwareVersion >= 2.0",