@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x031e/lzw31-sn.json

@@ -604,9 +604,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Start the inclusion process again on your HUB and tap the Configuration Button three (3) times.\n\nPlease Note: If this doesn't work, you can check to see if your switch is within Z-Wave Range by holding down the Configuration Button for 5-10 seconds (if it's not within range, the LED Bar will indicate Red and if it is within Range, the LED Bar will indicate Green). If your switch indicates Red, please move the switch closer to the HUB. If your switch indicates Green, please try running an Exclusion to reset your switch",
-		"exclusion": "To Exclude your dimmer, put your HUB in exclusion mode and press the Configuration Button three (3) times",
-		"reset": "You may factory reset the switch by holding down the Config Button for twenty (20) or more seconds. The LED Bar will turn Red and blink three (3) times to confirm. \n\nHowever, we recommend using a certified Z-Wave controller to remove the device from your network for factory resetting the switch. \n\nOnly use either of these procedures in the event that the network primary controller is missing or otherwise inoperable",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4206/LZW31-SN%20Manual%20-%20Inovelli%20Dimmer%20Switch%20(Red%20Series)%20-%2006.28.21.pdf"
+		"inclusion": "Tap the configuration button three times. The LED bar will indicate red if not within range or green if within range.",
+		"exclusion": "Press the configuration button three times.",
+		"reset": "Hold the configuration button for 20 seconds. The LED bar will turn red and after 20 seconds will rapidly blink red/blue. Release the button and the switch will factory reset.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3962/LZW31-SN%20Manual.pdf"
 	}
 }

package/config/devices/0x031e/lzw40.json

@@ -34,9 +34,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the power to the smart bulb turned off, start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on power to the bulb and it will blink twice (2x) indicating it's in inclusion mode. If the bulb was included successfully, it will blink one more (1x) time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there's still issues, please ensure your bulb is within range",
-		"exclusion": "If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you're within range and it's still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on. Your bulb will blink twice (2x), indicating it's in exclusion mode. When exclusion is successful, it will blink one more time (1x) to confirm. Your HUB should say that the device is excluded",
-		"reset": "You may power on/off the bulb 6x (between 0.5-2 seconds each time) or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable. Your bulb will flash twice to confirm factory reset",
+		"inclusion": "Turn off power to the smart bulb, then turn on power - the bulb will blink twice indicating inclusion mode. If successful, the bulb will blink once more",
+		"exclusion": "Turn the power on - the bulb will blink twice indicating exclusion mode. The bulb will blink once more when exclusion is successful",
+		"reset": "Power the bulb on/off 6 times (between 0.5-2 seconds each time). The bulb will flash twice to indicate factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3657/LZW40%20-%20Manual%20(Compressed).pdf"
 	}
 }

package/config/devices/0x031e/lzw41.json

@@ -70,9 +70,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on and off power to the bulb 3x (ie: Turn On, Turn Off, Turn On, Turn Off, Turn On) and the bulb should flash 3x indicating it's in inclusion mode. \nIf the bulb was included successfully, it will blink one more time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there's still issues, please ensure your bulb is within range",
-		"exclusion": "IMPORTANT: If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you're within range and it's still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on/off/on/off/on/off/on (3x on and 2x off) until your bulb blinks three (3x) and then blinks 1x to confirm. Your HUB should say that the device is excluded. You may then add (include) the bulb per the instructions below",
-		"reset": "You may power on/off the bulb 6x (between 0.5-2 seconds each time) or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable. Your bulb will flash twice to confirm factory reset",
+		"inclusion": "Turn power to the bulb on/off/on/off/on - the bulb will flash 3 times indicating inclusion mode. If successful, the bulb will blink once more",
+		"exclusion": "Turn power on/off/on/off/on/off/on (3 on, 2 off) - the bulb will blink 3 times. The bulb will blink once more when exclusion is successful",
+		"reset": "Power the bulb on/off 6 times (between 0.5-2 seconds each time). The bulb will flash twice to indicate factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3614/LZW41%20Manual.pdf"
 	}
 }

package/config/devices/0x031e/lzw42.json

@@ -62,9 +62,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the bulb turned off, start the inclusion process on your hub/gateway.  Once the inclusion process has started, turn on the bulb and it will immediately blink twice (2x) indicating it's in inclusion (pairing) mode.  If the bulb was included successfully, it will blink one more (1x) time.  If it was not included successfully, you may have to run an exclusion.  If there's still issues, please ensure your bulb is within range.",
-		"exclusion": "Put your hub in exclusion mode and turn the power to the bulb on.  Your bulb will blink twice (2x) indicating it's in exclusion mode.  When exclusion is successful, it will blink one more time (1x) to confirm.  Your hub should say that the device is excluded.",
-		"reset": "You may power on/off the bulb 6x (between 0.5-2 seconds each time) or use a certified controller to remove the device from your network to factory default.  Only use this procedure in the event that the network primary controller is missing or otherwise inoperable.  Your bulb will flash twice to confirm factory reset.",
+		"inclusion": "1. Turn off the bulb\n2. Turn on the bulb - it will blink twice indicating inclusion mode\n3. If successful, the bulb will blink once more",
+		"exclusion": "Turn power to the bulb on - it will blink twice indicating exclusion mode. The bulb will blink once more when exclusion is successful",
+		"reset": "Power the bulb on/off 6 times (between 0.5-2 seconds each time). The bulb will flash twice to indicate factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3613/LZW42%20Manual.pdf"
 	},
 	"compat": {

package/config/devices/0x031e/lzw60.json

@@ -191,9 +191,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press the sensor button 1x and the sensor will flash red rapidly. If successful, the sensor will stop flashing and the red light will be solid for 1-2 seconds, followed by the red light turning off. If unsuccessful, the red light will continue to rapidly flash until it times out after 25 seconds",
-		"exclusion": "Put your HUB in Exclusion mode and press the sensor button 1x. Your sensor will rapidly blink, indicating it's in exclusion mode. When exclusion is successful, the red light will stop blinking, turn solid red and then turn off",
-		"reset": "You may hold the Sensor Button for 5 seconds or use a certified controller to remove the device from your network to factory default. The sensors red LED will blink fast and then if successful, will turn off.\n\n \n\nOnly use this procedure in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the sensor button once. The sensor will flash red rapidly. If successful, the red light will be solid for 1-2 seconds then turn off",
+		"exclusion": "Press the sensor button once - the sensor will rapidly blink red. When successful, the red light will turn solid then off",
+		"reset": "Hold the sensor button for 5 seconds. The red LED will blink fast then turn off if successful",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3723/Inovelli%204-1%20Sensor%20Manual.pdf"
 	}
 }

package/config/devices/0x031e/vzw31-sn.json

@@ -848,7 +848,7 @@
 	"metadata": {
 		"inclusion": "Triple-click config button",
 		"exclusion": "Triple-click config button",
-		"reset": "Simultaneously hold the config button and the up button until the LED bar turns red.  Release the buttons and the switch will reset to factory defaults.",
+		"reset": "Simultaneously hold the config button and the up button until the LED bar turns red. Release the buttons and the switch will reset to factory defaults.",
 		"manual": "https://community.inovelli.com/t/resources-red-series-smart-2-1-switch-on-off-dimmer-manual/13706"
 	}
 }