@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x027a/zen20.json

@@ -290,9 +290,9 @@
 		"preserveRootApplicationCCValueIDs": true
 	},
 	"metadata": {
-		"inclusion": "1. Plug the Power Strip into a grounded receptacle you're planning to use it at (it doesn't need to be close to the hub) \n2. Initiate inclusion (pairing) in the app (or web interface). \n3. CLICK CH1 BUTTON 3 TIMES QUICKLY. All LED indicators will start flashing \n4. You will see 7 or 8 new on/off devices in your app: 5 channels or on/off control, 2 channels for on/off monitoring (USB ports reporting charging/ charged status, no control), and possibly one master node to access and adjust advanced settings in.",
-		"exclusion": "1. Bring the strip within direct range of your Z-Wave gateway (hub). \n2. Put the Z-Wave hub into exclusion mode. \n3. Press and release the CH1 button 3 times quickly. \n4. Your hub will confirm exclusion and all of the channels (child outlets) and the main device will disappear from your controller's device list.",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset \nthe device to factory settings. To complete the reset process manually, \nclick-click-click'n'hold CH1 button for at least 10 seconds. All LED indicators \nwill flash to confirm successful reset. NOTE: All previously recorded activity \nand custom settings EXCEPT for the kWh record will be erased from the device's memory.",
+		"inclusion": "1. Plug the Power Strip into a grounded receptacle\n2. Click CH1 button 3 times quickly\n3. All LED indicators will start flashing to confirm inclusion",
+		"exclusion": "Press and release the CH1 button 3 times quickly. All LED indicators will flash to confirm exclusion.",
+		"reset": "Click-click-click'n'hold CH1 button for at least 10 seconds. All LED indicators will flash to confirm successful reset.",
 		"manual": [
 			{
 				"$if": "firmwareVersion >= 4.10",

package/config/devices/0x027a/zen21.json

@@ -126,9 +126,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
-		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the dimmer 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "Tap the lower paddle 3 times quickly. The LED indicator will flash to confirm exclusion.",
+		"reset": "Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3667/zooz-z-wave-plus-on-off-switch-zen21-ver3.1-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen26.json

@@ -120,9 +120,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the switch 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
-		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the switch 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "Tap the lower paddle 3 times quickly. The LED indicator will flash to confirm exclusion.",
+		"reset": "Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3147/zooz-z-wave-plus-s2-on-off-switch-zen26-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen27.json

@@ -179,9 +179,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
-		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the dimmer 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "Tap the lower paddle 3 times quickly. The LED indicator will flash to confirm exclusion.",
+		"reset": "Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3148/zooz-z-wave-plus-s2-dimmer-switch-zen27-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen30.json

@@ -324,9 +324,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. Finalize inclusion at the switch. Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
-		"exclusion": "Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode \n3. Tap the lower paddle on the dimmer 3 times quickly\n4. Your hub will confirm exclusion and the device will disappear from your\ncontroller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset\nthe device to factory settings. To complete the reset process manually,\npress and hold the lower paddle on the dimmer for at least 15 seconds\nuntil the LED indicators start flashing, release. Then immediately press\nand hold the upper paddle on the dimmer for at least 15 seconds. The\nLED indicators will flash again to confirm successful reset",
+		"inclusion": "Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion.",
+		"exclusion": "1. Tap the lower paddle on the dimmer 3 times quickly\n2. The LED indicators will blink\n3. The LEDs will turn off when exclusion is complete",
+		"reset": "1. Press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release\n2. Immediately press and hold the upper paddle on the dimmer for at least 15 seconds\n3. The LED indicators will flash again to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3791/zooz-s2-double-switch-zen30-ver1-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zen32.json

@@ -292,9 +292,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "INCLUSION\n1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP THE SWITCH BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
-		"exclusion": "EXCLUSION\n1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. TAP THE SWITCH BUTTON 3 TIMES QUICKLY (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list\nreset",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the switch button for 20 seconds until the LED indicator starts flashing red. Release the button, and immediately a􀆞er, tap remote button 1 once to complete the reset. The LED indicators on all buttons will flash red to confirm a successful reset",
+		"inclusion": "Tap the switch button 3 times quickly. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if inclusion fails.",
+		"exclusion": "Tap the switch button 3 times quickly. The LED indicator will start blinking blue and turn green for 3 seconds when exclusion is complete.",
+		"reset": "Press and hold the switch button for 20 seconds until the LED indicator starts flashing red, then release the button and immediately tap remote button 1 once to complete the reset. The LED indicators on all buttons will flash red to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4131/zooz-z-wave-plus-scene-control-switch-zen32-online-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen34.json

@@ -170,10 +170,10 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "Put your Z-Wave hub into inclusion mode and click the upper paddle 6 times quickly. The LED indicator\nwill blink blue during the process and light up green once added successfully. It will light up red if failed",
-		"exclusion": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the lower paddle 6 times very quickly\n4. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"wakeup": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Click the upper paddle 7 times very quickly\n3. Your device's indicator light will remain on to indicate that the device is awake.",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the process, make sure the device is powered, then tap-tap-\ntap'and'hold the upper paddle. The LED indicator will blink red 5 times to indicate successful reset",
+		"inclusion": "Click the upper paddle 6 times quickly. The LED indicator will blink blue during the process and light up green once added successfully.",
+		"exclusion": "Click the lower paddle 6 times quickly. The LED indicator will blink and turn off when exclusion is complete.",
+		"wakeup": "Click the upper paddle 7 times very quickly. The indicator light will remain on to indicate that the device is awake.",
+		"reset": "Tap-tap-tap and hold the upper paddle. The LED indicator will blink red 5 times to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4114/zooz-700-series-remote-switch-zen34-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zen37.json

@@ -153,10 +153,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put your Z-Wave hub into inclusion mode and click the upper paddle 6 times quickly. The LED indicator\nwill blink blue during the process and light up green once added successfully. It will light up red if failed",
-		"exclusion": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the lower paddle 6 times very quickly\n4. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"wakeup": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Click the lower left button 6 times as quickly as possible to wake the device up\n3. Your device's indicator light will remain on to indicate that the device is awake.",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the device is powered, then click the bottom right small button 6 times quickly. The LED indicator will start blinking red, then immediately click the same button 6 more times. The LED indicator will stay red for 2 seconds.",
+		"inclusion": "Click the upper paddle 6 times quickly. The LED indicator will blink blue during the process and light up green once added successfully. It will light up red if failed.",
+		"exclusion": "Click the lower paddle 6 times very quickly.",
+		"wakeup": "Click the lower left button 6 times as quickly as possible to wake the device up. The device's indicator light will remain on to indicate that the device is awake.",
+		"reset": "Click the bottom right small button 6 times quickly. The LED indicator will start blinking red. Immediately click the same button 6 more times. The LED indicator will stay red for 2 seconds.",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-800-series-z-wave-long-range-wall-remote-zen37-800lr-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen71.json

@@ -139,9 +139,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. Finalize inclusion at the switch. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicator will blink blue. It will turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "Tap the lower paddle 3 times quickly. The LED indicator will start blinking blue. It will turn green for 3 seconds when exclusion is successful.",
+		"reset": "1. Press and hold the lower paddle for 10 seconds until the LED indicator starts blinking.\n2. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4103/zooz-700-series-switch-zen71-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen72.json

@@ -219,9 +219,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicator will blink blue and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "1. Tap the lower paddle on the switch 3 times quickly\n2. The LED indicator will start blinking blue\n3. It will turn green for 3 seconds when exclusion is complete",
+		"reset": "1. Press and hold the lower paddle for 10 seconds until the LED indicator starts blinking\n2. Release paddle\n3. Immediately tap the lower paddle 5 times to complete the reset\n4. It will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4108/zooz-700-series-z-wave-dimmer-zen72-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen73.json

@@ -75,9 +75,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the switch down 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list reset",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, hold the toggle down for 10 seconds until the LED indicator starts blinking. Release the toggle, and immediately after, toggle the switch down 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
+		"inclusion": "Tap the switch up 3 times quickly. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "1. Tap the switch down 3 times quickly\n2. The LED indicator will start blinking blue\n3. It will turn green for 3 seconds when exclusion is complete",
+		"reset": "1. Hold the toggle down for 10 seconds until the LED indicator starts blinking\n2. Release the toggle\n3. Immediately toggle the switch down 5 times to complete the reset\n4. The LED will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4161/zooz-700-series-toggle-switch-zen73-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zen74.json

@@ -135,9 +135,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Toggle the switch down 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the toggle down for 10 seconds until the LED indicator starts blinking. Release toggle, and immediately after, toggle the switch down 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
+		"inclusion": "Tap up 3 times quickly. The LED indicator will blink blue and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "Toggle the switch down 3 times quickly. The LED indicator will start blinking blue and turn green for 3 seconds when exclusion is complete.",
+		"reset": "1. Press and hold the toggle down for 10 seconds until the LED indicator starts blinking\n2. Release toggle\n3. Immediately toggle the switch down 5 times to complete the reset\n4. The LED will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4164/zooz-700-series-toggle-dimmer-zen74-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zen76.json

@@ -113,9 +113,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicator will blink to signal communication.",
+		"exclusion": "1. Tap the lower paddle on the switch 3 times quickly\n2. The LED indicator will start blinking blue\n3. It will turn green for 3 seconds when exclusion is complete",
+		"reset": "1. Press and hold the lower paddle for 10 seconds until the LED indicator starts blinking\n2. Release paddle\n3. Immediately tap the lower paddle 5 times to complete the reset\n4. It will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4104/zooz-zen76-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen77.json

@@ -192,9 +192,9 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.\n3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
-		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.",
+		"inclusion": "Tap the upper paddle 3 times quickly. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.",
+		"exclusion": "1. Tap the lower paddle on the switch 3 times quickly\n2. The LED indicator will start blinking blue\n3. The LED indicator will turn green for 3 seconds when exclusion is complete",
+		"reset": "1. Press and hold the lower paddle for 10 seconds until the LED indicator starts blinking\n2. Release paddle\n3. Immediately tap the lower paddle 5 times to complete the reset\n4. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4109/21-1-7-zen77-ver1.03-manual-curves.pdf"
 	}
 }

package/config/devices/0x027a/zse01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Power the siren up and bring it in within 3 feet from your controller.\n2. Put your Z-Wave controller in inclusion mode.\n3. Press the Z-Wave button on the siren THREE times quickly.\n4. A new alarm device should appear on your controller's dashboard",
-		"exclusion": "1. Bring the siren within 3 feet from your Z-Wave gateway controller.\n\n2. Put your Z-Wave controller in exclusion/unpairing mode.\n\n3. Press and release the Z-Wave button on the siren THREE TIMES quickly.\n\n4. The device should disappear from your controller's device list.\n\nPlease repeat the process following all steps carefully if first attempt is unsuccessful",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the Z-Wave button for 10 seconds. \nNOTE: All previously recorded activity and custom settings will be erased from the siren's memory",
+		"inclusion": "Press the Z-Wave button 3 times quickly.",
+		"exclusion": "Press and release the Z-Wave button 3 times quickly.",
+		"reset": "Press and hold the Z-Wave button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1747/zooz-z-wave-indoor-siren-zse01-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse02.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Bring the motion sensor within 3 feet from your controller.\n2. Put your Z-Wave controller in inclusion mode.\n3. Press and release the Z-Wave button on the motion sensor TWICE quickly (to lock and unlock it).\n4. A new motion detection device should appear on your controller's dashboard",
-		"exclusion": "1. Bring the motion sensor within 3 feet from your controller.\n2. Put your Z-Wave controller in exclusion mode.\n3. Press and release the Z-Wave button on the motion sensor TWICE quickly (to lock and unlock it).\n4. The device should disappear from your controller's dashboard.",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, please press the Z-Wave SIX TIMES quickly (3 lock-unlock cycles).\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory.",
+		"inclusion": "Press and release the Z-Wave button twice quickly (to lock and unlock it).",
+		"exclusion": "Press and release the Z-Wave button twice quickly (to lock and unlock it).",
+		"reset": "Press the Z-Wave button 6 times quickly (3 lock-unlock cycles).",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1743/zooz-z-wave-motion-sensor-zse02-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse11.json

@@ -149,9 +149,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put your Z-Wave hub into inclusion mode and click the Z-Wave button 3 times as quickly as possible. The LED indicator will start blinking to confirm inclusion mode and turn off once inclusion is completed. The sensor will automatically pair as a repeater if connected to USB power, no special button sequence required",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Press and release the Z-Wave button 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then press and hold the Z-Wave button for at least 20 seconds.\nThe LED indicator will start flashing and turn solid on for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
+		"inclusion": "Click the Z-Wave button 3 times quickly. The LED indicator will start blinking to confirm inclusion mode and turn off once inclusion is completed.",
+		"exclusion": "Press and release the Z-Wave button 3 times quickly.",
+		"reset": "Press and hold the Z-Wave button for at least 20 seconds. The LED indicator will start flashing and turn solid on for a couple of seconds to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4152/zooz-q-sensor-zse11-ver1-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zse18.json

@@ -64,10 +64,10 @@
 		}
 	],
 	"metadata": {
-		"wakeup": "Press and HOLD the Z-Wave button for 5 seconds to wake the device up. The LED will start flashing.",
-		"inclusion": "1. Bring the sensor within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into inclusion mode.\n3. Press and release the Z-Wave button 3 times quickly. The LED indicator will start blinking fast and turn solid for a second to confirm inclusion.",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave gateway controller (hub).\n2. Put the Z-Wave hub into exclusion mode.\n3. Press and release the Z-Wave button on the sensor 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the device will disappear from your controller's device list.",
-		"reset": "To complete the reset process manually, press and HOLD the Z-Wave button on the sensor for at least 20 seconds. The LED indicator will flash, stay solid, and then turn off to confirm factory reset.",
+		"wakeup": "Press and hold the Z-Wave button for 5 seconds to wake the device up. The LED will start flashing.",
+		"inclusion": "Press and release the Z-Wave button 3 times quickly. The LED indicator will start blinking fast and turn solid for a second to confirm inclusion.",
+		"exclusion": "Press and release the Z-Wave button on the sensor 3 times as quickly as possible.",
+		"reset": "To complete the reset process manually, press and hold the Z-Wave button on the sensor for at least 20 seconds. The LED indicator will flash, stay solid, and then turn off to confirm factory reset.",
 		"manual": "https://www.getzooz.com/downloads/zooz-z-wave-plus-motion-sensor-zse18-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse29.json

@@ -137,9 +137,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "AUTO-INCLUSION:\n1. Initiate inclusion (pairing) in the app (or web interface). Not Sure how? ask@getzooz.com. If you're using an S2 hub, it may ask you to enter the DSK key printed on the back cover sticker to complete secure inclusion.\n2. Insert the batteries or the USB adapter board. The LED indicator\nwill start blinking and the sensor will join the network Automatically.\n\nMANUAL INCLUSION:\nPut your Z-Wave hub into inclusion mode and click the tamper switch 3 times quickly",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave\ngateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure\nhow to do that? ask@getzooz.com).\n3. Press and release the tamper switch 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will\ndisappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then CLICKCLICK-CLICK-CLICK'N'HOLD the tamper switch for AT LEAST 5 SECONDS. The LED indicator will turn off to\nindicate successful reset. The sensor will then enter auto-inclusion mode for 4 minutes.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory.",
+		"inclusion": "Click the tamper switch 3 times quickly. The LED indicator will start blinking and the sensor will join the network automatically.",
+		"exclusion": "1. Press and release the tamper switch 3 times quickly\n2. The LED indicator will blink\n3. The LED will turn off when exclusion is complete",
+		"reset": "Click-click-click and hold the tamper switch for at least 5 seconds. The LED indicator will turn off to indicate successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3081/zooz-z-wave-plus-s2-outdoor-motion-sensor-zse29-manual.pdf"
 	},
 	"compat": {

package/config/devices/0x027a/zse40.json

@@ -271,9 +271,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface).\nClick the Z-Wave button with a paperclip twice. The LED indicator will start flashing",
-		"exclusion": "Initiate exclusion in the app (or web interface).\nClick the Z-Wave button with a paperclip twice. The LED indicator will start flashing",
-		"reset": "If your primary controller is missing or\ninoperable, you may need to reset the\ndevice to factory settings. To complete\nthe reset process manually, remove the\nback cover to trigger tamper switch.\nPress and release the Z-Wave button\nusing a paperclip 10 TIMES quickly\n(within 10 seconds)",
+		"inclusion": "Click the Z-Wave button with a paperclip twice. The LED indicator will start flashing.",
+		"exclusion": "Click the Z-Wave button with a paperclip twice. The LED indicator will start flashing.",
+		"reset": "1. Remove the back cover to trigger tamper switch\n2. Press and release the Z-Wave button using a paperclip 10 times quickly (within 10 seconds)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4307/zooz-zse40-700-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zse41.json

@@ -75,10 +75,10 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\n\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
-		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off once inclusion is completed.",
+		"exclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off when exclusion is complete.",
+		"reset": "1. Click the Z-Wave button twice and hold it the third time for 10 seconds\n2. The LED indicator will blink continuously\n3. Immediately click the Z-Wave button twice more to finalize the reset\n4. The LED indicator will flash 3 times to confirm a successful reset",
+		"wakeup": "Click the Z-Wave button 4 times quickly. The LED indicator will flash twice to confirm the device is awake.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4276/zooz-zse41-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zse42.json

@@ -73,10 +73,10 @@
 		"skipConfigurationInfoQuery": true
 	},
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
-		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off once inclusion is completed.",
+		"exclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off when exclusion is complete.",
+		"reset": "1. Click the Z-Wave button twice and hold it the third time for 10 seconds\n2. The LED indicator will blink continuously\n3. Immediately click the Z-Wave button twice more to finalize the reset\n4. The LED indicator will flash 3 times to confirm a successful reset",
+		"wakeup": "Click the Z-Wave button 4 times quickly. The LED indicator will flash twice to confirm the device is awake.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4280/zooz-zse42-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse43.json

@@ -169,10 +169,10 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
-		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off once inclusion is completed.",
+		"exclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off when exclusion is complete.",
+		"reset": "1. Click the Z-Wave button twice and hold it the third time for 10 seconds\n2. The LED indicator will blink continuously\n3. Immediately click the Z-Wave button twice more to finalize the reset\n4. The LED indicator will flash 3 times to confirm a successful reset",
+		"wakeup": "Click the Z-Wave button 4 times quickly. The LED indicator will flash twice to confirm the device is awake.",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-700-series-tilt-shock-xs-sensor-zse43-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse44.json

@@ -402,9 +402,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off once inclusion is completed.",
+		"exclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing and turn off when exclusion is complete.",
+		"reset": "1. Click the Z-Wave button twice and hold it the third time for 10 seconds\n2. The LED indicator will blink continuously\n3. Immediately click the Z-Wave button twice more to finalize the reset\n4. The LED indicator will flash 3 times to confirm a successful reset",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-700-series-tilt-shock-xs-sensor-zse43-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse70_800lr.json

@@ -301,9 +301,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put your Z-Wave® hub into inclusion mode and click\nthe Z-Wave® button 3 times as quickly as possible. The\nLED indicator will start blinking to confirm inclusion\nmode and turn off once inclusion is completed",
-		"exclusion": "1. Bring the sensor within direct range of your Z-Wave®\ngateway (hub).\n2. Put the Z-Wave® hub into exclusion mode (not sure\nhow to do that? ask@getzooz.com).\n3. Click the Z-Wave® button 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will\ndisappear from your controller''s device list",
-		"reset": "When your network's primary controller is missing or\notherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the\nprocess, make sure the sensor is powered, then hold\nthe Z-Wave® button down for at least 10 seconds.\nThe LED indicator will start flashing blue and turn solid\nblue for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be\nerased from the device's memory",
+		"inclusion": "Click the Z-Wave button 3 times as quickly as possible. The LED indicator will start blinking and turn off once inclusion is completed.",
+		"exclusion": "1. Click the Z-Wave button 3 times quickly\n2. The LED indicator will start blinking\n3. The LED will turn off when exclusion is complete",
+		"reset": "Hold the Z-Wave button down for at least 10 seconds. The LED indicator will start flashing blue and turn solid blue for a couple of seconds to indicate successful reset.",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-zse70-800lr-manual.pdf"
 	}
 }

package/config/devices/0x027b/sh-zw_cbb_ut.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Click on the Z-Wave Toolbox link found on the Admin tab. Here you will see the Reset Defaults button. Pressing this button brings up the following warning.\n\nCAUTION: This will factory reset the Z-Wave controller in the hub. This will cause all of the devices to become disconnected from the hub, and they'll have to be excluded and included again to function. In addition, any pending edits that you've made in the portal will be lost. Are you sure you want to continue?\n\nSelecting Yes will result in a complete reset of the controller",
+		"reset": "1. Click on the Z-Wave Toolbox link found on the Admin tab\n2. Press the Reset Defaults button\n3. Select Yes to confirm",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2509/white%20rabbit%20automation%20system%20user%20guide%20(1).pdf"
 	}
 }

package/config/devices/0x028c/pwly-274343.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Launch the Powerley app. From the navigation menu, select My Devices (Device icon), select Energy Bridge. On the Energy Bridge tab, scroll to \"Z-Wave\", and select \"Reset Network\", and on the next screen, tap \"Begin Z-Wave Network Reset\". A warning will display alerting the user that this will reset the network and disconnect all devices and to only use in the event the network or device is no longer operable. The screen will then ask the user to confirm by typing \"RESET\" to complete the factory reset.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Launch the Powerley app and select My Devices\n2. Select Energy Bridge, then scroll to Z-Wave and select Reset\n3. Tap Begin Z-Wave Reset\n4. Type \"RESET\" to confirm the factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2744/pwly-eb-manual-180202.pdf"
 	}
 }

package/config/devices/0x029c/o2_smart_box_2.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "O2 Smart Box is mainly controlled from within O2 Smart Box application for smartphones. \nIn section Add new device in our application, customer selects type of device and application activates inclusion mode at the gateway",
-		"exclusion": "O2 Smart Box is mainly controlled from within O2 Smart Box application for smartphones. \nIn detail of every Z-Wave device, customer can find option to \"Unpair device\". When he selects this option, gateway enters exclusion mode and instruction how to exclude this device is shown in application (e.g. Click the pairing button three times within one second)",
-		"reset": "Select the Factory Reset item in the Advanced drop-down menu in WebUI.\nSelect the Factory Reset item in settings section in O2 Smart Box application",
+		"inclusion": "In the Add new device section of the O2 Smart Box smartphone app, select the device type to activate inclusion mode.",
+		"exclusion": "In the device details of the O2 Smart Box smartphone app, select \"Unpair device\" to enter exclusion mode and follow the displayed instructions.",
+		"reset": "Select Factory Reset from the Advanced drop-down menu in the WebUI or from the settings section in the O2 Smart Box app.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4476/sb2_manual%20(1).pdf"
 	}
 }

package/config/devices/0x030a/dt82tv_f-1_2_14.json

@@ -203,9 +203,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press the motor setting button three times within 1.5 seconds. (Press P1 (1 beep), Press P1 (1 beep), Press P1( 1 beep and 1 jog))",
-		"exclusion": "Press the motor setting button three times within 1.5 seconds. (Press P1 (1 beep), Press P1 (1 beep), Press P1 (1 beep and 1 jog))",
-		"reset": "Press and hold P1 for 10 seconds (Press and hold P1 button for 2 seconds, the motor will long beep once and jog once; for 5 seconds, 3 beeps and jog once if no limits; for 10 seconds, 3 beeps and jog once; release the P1 button, 16 beeps and jog once.)\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the motor setting button three times within 1.5 seconds. The motor will beep and jog after the third press.",
+		"exclusion": "Press the motor setting button three times within 1.5 seconds. The motor will beep and jog after the third press.",
+		"reset": "Press and hold P1 for 10 seconds. The motor will long beep once and jog once after 2 seconds, 3 beeps and jog once after 5 seconds, 3 beeps and jog once after 10 seconds. Release the P1 button, the motor will beep 16 times and jog once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3343/DM35ECB-F.pdf"
 	}
 }

package/config/devices/0x030c/fios-g1100-v1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Bring up Verizon Connected Home mobile application ('CoHo App'). Navigate to the 'Z-Wave Troubleshooting' page in one of the following ways: a) Triple bar icon -> Support -> 'Z-Wave Troubleshooting'. b) Triple bar icon -> Device Screen -> Axon gateway -> 'Z-Wave Troubleshooting Tools'.\nFrom there, press 'Reset' button, to reset the Z-Wave network, this will remove all devices from the controller. \nBHR is the primary controller for Z-Wave network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.",
+		"reset": "1. Bring up Verizon Connected Home mobile application.\n2. Navigate to 'Z-Wave Troubleshooting' page via Triple bar icon -> Support -> 'Z-Wave Troubleshooting' or Triple bar icon -> Device Screen -> Axon gateway -> 'Z-Wave Troubleshooting Tools'.\n3. Press 'Reset' button to reset the Z-Wave network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2826/Coho%20Quick%20Start%20Guide.pdf"
 	}
 }

package/config/devices/0x0312/n4002.json

@@ -37,7 +37,7 @@
 		},
 		{
 			"#": "9",
-			"label": "Ramp Rate (On/Off Control)",
+			"label": "Dimming Rate (Normal)",
 			"valueSize": 1,
 			"unit": "seconds",
 			"minValue": 0,
@@ -46,7 +46,7 @@
 		},
 		{
 			"#": "10",
-			"label": "Ramp Rate (Dimmer/Z-Wave Control)",
+			"label": "Dimming Rate (Local Dimmer Control)",
 			"valueSize": 1,
 			"unit": "seconds",
 			"minValue": 0,

package/config/devices/0x031c/zweve-usb-0001.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "The host software controls how to reset it",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2469/manual.pdf"
 	}
 }

package/config/devices/0x031d/zweecit1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Place the network controller into inclusion mode by following the manufacturer's instructions, then in the CIT user interface, on the home page, click \"Join Network\"",
-		"exclusion": "Place the network controller into exclusion mode by following the manufacturer's instructions, then in the CIT user interface, on the home page, click \"Leave Network\"",
-		"reset": "If the CIT is the primary controller for a network (not recommended) following this procedure will result in nodes being orphaned (no controller). If the CIT is a part of a network, following this procedure will leave an invalid node in the list for the primary controller. Therefore, under these two conditions above, use this procedure only if the network primary controller is missing or is otherwise inoperable.\n\nIn the CIT user interface, click the menu item Network, then Control, and then on the control page click \"Controller Factory Default\"",
+		"inclusion": "In the CIT user interface, on the home page, click \"Join Network\".",
+		"exclusion": "In the CIT user interface, on the home page, click \"Leave Network\".",
+		"reset": "In the CIT user interface, click the menu item Network, then Control, and then on the control page click \"Controller Factory Default\".",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2465/Z-Wave%20Alliance%20Certified%20Installer%20Toolkit%20User%20Guide%20(v1.0).pdf"
 	}
 }

package/config/devices/0x031e/lzw30-sn.json

@@ -424,9 +424,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To include your on/off switch start the inclusion process on your HUB and tap the Configuration Button three (3) times.\n\nPlease Note: If this doesn't work, you can check to see if your switch is within Z-Wave Range by holding down the Configuration Button for 5-10 seconds (if it's not within range, the LED Bar will indicate Red and if it is within Range, the LED Bar will indicate Green). If your switch indicates Red, please move the switch closer to the HUB. If your switch indicates Green, please try running an Exclusion to reset your switch",
-		"exclusion": "To Exclude your switch, put your HUB in exclusion mode and press the Configuration Button three (3) times",
-		"reset": "You may factory reset the switch by holding down the Config Button for twenty (20) or more seconds. The LED Bar will turn Red and blink three (3) times to confirm. \n\nHowever, we recommend using a certified Z-Wave controller to remove the device from your network for factory resetting the switch. \n\nOnly use either of these procedures in the event that the network primary controller is missing or otherwise inoperable",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4197/LZW30-SN%20Manual%20-%20Inovelli%20On-Off%20Switch%20(Red%20Series)%20-%2006.28.21.pdf"
+		"inclusion": "Tap the configuration button three times. The LED bar will indicate red if not within range or green if within range.",
+		"exclusion": "Press the configuration button three times.",
+		"reset": "Hold the configuration button for 20 seconds. The LED bar will turn red and after 20 seconds will rapidly blink red/blue. Release the button and the switch will factory reset.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4197/LZW30-SN%20Manual.pdf"
 	}
 }