@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x041a/kp-sw-08.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "• Connect the power supply. \n• Set the Z-Wave network main controller into learning mode. \n• Press and hold the button 1 (the red light flashes slowly) until the pink light flashes slowly and then release, the device sends the network k information (blue light flashes quickly). \n• After the network is successfully connected, the LED indicator of the device is steady blue, and the load is off by default.",
-		"exclusion": "• Power on the switch. \n• Set the Z-Wave network controller into the exclusion mode. \n• Long press the switch button 1 (Red LED blink slowly) when Pink LED indicator light blink slowly, release the button, then the device start to send out exclusion information(Blue LED indicator in quick blinking). \n• When exclusion successfully, LED display is steady blue, load is off.",
-		"reset": "Reset procedure will delete all information in the Z-Wave network or Z-Wave gateway, and will restore switch to factory default settings. \n• Make sure switch is powered. \n• Press and hold the Switch button 1 for 20 seconds. \n• Until the pink light is always on, release the button. \n Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Connect the power supply\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when successfully connected",
+		"exclusion": "1. Power on the switch\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when exclusion is successful",
+		"reset": "1. Ensure the switch is powered\n2. Press and hold button 1 for 20 seconds\n3. Release the button when the pink LED is always on",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3587/KP-SW-08.pdf"
 	}
 }

package/config/devices/0x041b/39446_zw3107.json

@@ -133,8 +133,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\ndimmer. Repeat as necessary to add the dimmer to\nthe network.\nYou have complete control",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\ndimmer to remove it from the network",
-		"reset": "1. If plugged in, unplug the dimmer from the receptacle\n2. Press and hold the top button, plug the device in and\ncontinue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart dimmer.",
+		"exclusion": "Press and release the manual/program button on the smart dimmer.",
+		"reset": "1. If plugged in, unplug the dimmer from the receptacle\n2. Press and hold the top button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39449_zw4106.json

@@ -58,8 +58,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\nswitch. Repeat as necessary to add the switch to\nthe network",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\nswitch to remove it from the network",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in and\ncontinue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart switch.",
+		"exclusion": "Press and release the manual/program button on the smart switch.",
+		"reset": "1. If plugged in, unplug the device from the receptacle\n2. Press and hold the top button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39453_zw4203.json

@@ -79,8 +79,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the manual/program button on the smart\nswitch to add it in the network.\n3. The controller's app will indicate if it has discovered the\nswitch. If prompted by the controller to enter the S2\nsecurity code, refer to the QR code/security number on\nthe side of the box or the QR code label on the product\n(see Figure 1). Enter the 5-digit code",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the manual/program button on the smart\nswitch to remove it from the network",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the manual/program button, plug the\ndevice in and continue to hold for at least 3 seconds.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable"
+		"inclusion": "Press and release the manual/program button on the smart switch.",
+		"exclusion": "Press and release the manual/program button on the smart switch.",
+		"reset": "1. If plugged in, unplug the device from the receptacle\n2. Press and hold the manual/program button, plug the device in and continue to hold for at least 3 seconds"
 	}
 }

package/config/devices/0x041b/39455_zw4008.json

@@ -78,9 +78,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the smart switch (rocker) to add it in the network.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the smart switch (rocker) to remove it from the network",
-		"reset": "Quickly press ON (top) button three times, then, immediately press the OFF (bottom) button three times. The LED indicator will flash ON/OFF five times when completed successfully.\nNOTE: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the top or bottom of the switch.",
+		"exclusion": "Press and release the top or bottom of the switch.",
+		"reset": "1. Quickly press the top button three times\n2. Immediately press the bottom button three times\n3. The LED will flash ON/OFF five times when completed successfully",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4169/39455_HQSG_v4.pdf"
 	}
 }

package/config/devices/0x041b/39456_zw1002.json

@@ -58,8 +58,8 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a\ndevice to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the\nprogram button. Repeat as necessary to add the smart outlet to\nthe network.\nYou have complete control",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a\ndevice from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the\nmanual/program button",
-		"reset": "Quickly press the button three times. Then, press the button for at least three\nseconds. The LED will blink five times to confirm.\nNote: This should only be used in the event your network's primary controller\nis missing or otherwise inoperable"
+		"inclusion": "Press and release the program button.",
+		"exclusion": "Press and release the program button.",
+		"reset": "1. Quickly press the button three times\n2. Press the button for at least three seconds\n3. The LED will blink five times to confirm"
 	}
 }

package/config/devices/0x041b/39458_zw3010.json

@@ -142,8 +142,7 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "This dimmer is SmartStart enabled. If your controller supports SmartStart inclusion, this dimmer can be added into the Z-Wave network by following the instructions for your controller or hub and scanning the Z-Wave QR Code on the front or on the package when instructed. No further action is required, and the dimmer will be added automatically within 10 minutes of being powered up while in range Z-Wave network.",
-		"exclusion": "Press on 2 times and off 2 times. LED will flash 5 times if exclusion was successful.",
-		"reset": "Quickly press ON button 3 times then immediately press the Off button 3 times. The LED will flash ON/OFF 5 times when completed successfully"
+		"exclusion": "Press ON 2 times and OFF 2 times (LED will flash 5 times if successful).",
+		"reset": "1. Quickly press ON button 3 times\n2. Immediately press the OFF button 3 times\n3. The LED will flash ON/OFF 5 times when completed successfully"
 	}
 }

package/config/devices/0x041b/proa7pl.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If the Control Panel is the primary controller for your network, resetting it results in the devices in your\nnetwork to be orphaned and is necessary after the reset to exclude and re-include all the devices in the network. This defaults the Z-Wave Controller in the system which removes all programmed Z-Wave devices, however, the devices do not receive a signal to be excluded. So, when they need to be included, they need to be excluded first",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3675/800-25080A_PROA7PLUS_UG.PDF"
 	}
 }

package/config/devices/0x041b/smco410.json

@@ -0,0 +1,57 @@
+{
+	"manufacturer": "First Alert",
+	"manufacturerId": "0x041b",
+	"label": "SMCO410",
+	"description": "Smoke & CO Alarm",
+	"devices": [
+		{
+			"productType": "0x0001",
+			"productId": "0x0410",
+			"zwaveAllianceId": 5196
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"associations": {
+		"1": {
+			"label": "Lifeline",
+			"maxNodes": 5,
+			"isLifeline": true
+		}
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"label": "Supervision Report Timeout",
+			"valueSize": 2,
+			"unit": "ms",
+			"minValue": 500,
+			"maxValue": 5000,
+			"defaultValue": 1500
+		},
+		{
+			"#": "2",
+			"label": "Supervision Retry Count",
+			"valueSize": 2,
+			"minValue": 0,
+			"maxValue": 2,
+			"defaultValue": 1
+		},
+		{
+			"#": "3",
+			"label": "Supervision Wait Time",
+			"valueSize": 2,
+			"unit": "seconds",
+			"minValue": 1,
+			"maxValue": 60,
+			"defaultValue": 5
+		}
+	],
+	"metadata": {
+		"inclusion": "Press and hold the button until the device chirps twice and the green LED flashes",
+		"exclusion": "Press and hold the button until the device chirps twice and the green LED flashes",
+		"reset": "Press and hold the button until the device chirps 3 times. This may take 20+ seconds."
+	}
+}

package/config/devices/0x041b/tuxedow.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. At the TUXEDOW Home screen:\n a) Press the Devices icon and then press the SETUP icon to display 'Z-Wave Device Management' screen.\n b) Press the ADD DEVICE icon.\n2. At the device Module:\na) Press the Function Key on the device",
-		"exclusion": "1. At the TUXEDOW Home screen:\n a) Press the Devices and Setup icons to display the 'Z-Wave Device Management' screen.\n b) Highlight the device to remove and press the Remove Device icon.\n2. At the device module:\n a) Press the Function Key to remove the device from the keypad",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nTo activate the Keypad Reset function, press the Setup, System Setup and Advanced Setup icons\n\n1. Enter your Authorized Code and press the Keypad Reset icon.\n\n2. Select OK or Cancel",
+		"inclusion": "Press the Function Key on the device.",
+		"exclusion": "Press the Function Key on the device.",
+		"reset": "1. Press the Setup, System Setup and Advanced Setup icons\n2. Enter your Authorized Code and press the Keypad Reset icon\n3. Confirm with OK",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3624/800-25178B_QIG_TUXEDOW.pdf"
 	}
 }

package/config/devices/0x041c/51110.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Click [Add] icon in Z-Wave Controller.\n- Press the SW_Button 3 times within 1.5s, Blue LED is Blinking 3 times within 1 second.\n- If add Process is successful, Blue LED will turn off.",
-		"exclusion": "- Click [Remove] icon in Z-Wave Controller. \n- Press the SW_Button 3 times within 1.5s \n- If remove Process is successful, blue LED is Blinking 6 times, then turn off.",
-		"reset": "- Long press SW_Button at least 10 seconds. \n- Device Reset Locally notification is Transmitted.\n-Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (blue LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (blue LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3262/51110_manual_EN_NO_SV20190425.pdf"
 	}
 }

package/config/devices/0x041c/51111.json

@@ -32,9 +32,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "-Press Func_Button 3 time in the motion sensor, Green LED is Blinking 3 times within 1 second.\n-If Inclusion Process is successful, Green LED will turn off.",
-		"exclusion": "-Press Func_Button 3 times quickly.\n-If Exclusion Process is successful, Green LED is Blinking 6 times, then turn off.",
-		"reset": "-Long press Func_Button while installing batteries \n-Device Reset Locally notification is Transmitted\n-Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times quickly (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button while installing batteries.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3275/51111%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041c/51112.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.\n- If Inclusion Process is successful, Green LED will turn off.",
-		"exclusion": "- Press the Net_Button 3 times within 1.5s. \n- If Exclusion Process is successful, Green LED is Blinking 6 times, then turn off.",
-		"reset": "- Long press Net_Button at least 10 seconds in the product. \n- Device Reset Locally notification is Transmitted.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3361/51112%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041c/51114.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "- Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.\n- If Inclusion Process is successful, Green led will turn off.",
-		"exclusion": "- Press the Net_Button 3 times within 1.5s. \n- If Exclusion Process is successful, Green led is Blinking 6 times, then turn off.",
-		"reset": "- Long press Net_Button at least 10 seconds in the product. \n- Device Reset Locally notification is Transmitted.\n- Please use this procedure only when the network primary controller is missing or otherwise.",
+		"inclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 3 times, then turns off when successful).",
+		"exclusion": "Press the button 3 times within 1.5 seconds (green LED blinks 6 times, then turns off when successful).",
+		"reset": "Press and hold the button for at least 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3365/51114%20user%20manual.pdf"
 	}
 }

package/config/devices/0x041e/eih-100e.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- This is the Z-Wave Set Default network operation and a confirmation message appears.\n- If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3569/EIH-100E_User_Manual.pdf"
 	}
 }

package/config/devices/0x042a/zd2105us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2105 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2105 then the device will send a signal to be included (or excluded) to/from the network; otherwise, ZD2105 will go to sleep after 20 seconds",
-		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZD2105 from your controller. Press the program switch of ZD2105 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2105 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch of ZD2105.",
+		"exclusion": "Press the program switch of ZD2105 for 1 second.",
+		"reset": "1. Trigger the rear cover switch to send the Alarm Report\n2. Trigger the reed switch (close & open) 5 times in 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3583/ZD2105-5%20GCS.pdf"
 	}
 }

package/config/devices/0x042c/wmbr.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)\n2. Select the About page\n3. Select ‘Advanced Z-Wave Utilities'\n4. Select ‘Add device'\n5. Refer to the manufacturer's instruction for inclusion using the DSK (device specific key). A user may attempt to use classic inclusion by entering `00000` as the DSK.\n6. The app will indicate when device inclusion is successful",
-		"exclusion": "EXCLUSION\n1. From the home screen, navigate to the Settings page by pressing the (insert gear icon)\n2. Select the About page\n3. Select ‘Advanced Z-Wave Utilities'\n4. Select ‘Exclude garage opener' to put the bridge in Exclusion Mode. Refer to the manufacturer's instruction for exclusion.\n5. The app will indicate when device exclusion is successful.",
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nTo factory reset the WiFi Bridge, which will also factory reset and delete all Z-Wave network information, press and hold the button on the back of the bridge for 20 seconds",
+		"inclusion": "1. Navigate to the Settings page by pressing the gear icon\n2. Select the About page\n3. Select 'Advanced Z-Wave Utilities'\n4. Select 'Add device'\n5. Enter 00000 as the DSK for classic inclusion",
+		"exclusion": "1. Navigate to the Settings page by pressing the gear icon\n2. Select the About page\n3. Select 'Advanced Z-Wave Utilities'\n4. Select 'Exclude garage opener'\n5. Refer to the manufacturer's instruction for exclusion",
+		"reset": "Press and hold the button on the back of the bridge for 20 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3673/Updated%20User%20Manual%209.20.pdf"
 	}
 }

package/config/devices/0x042f/connect2.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Start inclusion, per instructions on the existing network controller.\nIn the UI, press the learn button.\nWhen prompted, enter the 5 digit underlined portion of the DSK code.\nVerify secure inclusion completed successfully on the existing network controller per that documentation",
-		"exclusion": "Start exclusion, per instructions on the existing network controller.\nIn the UI, press the learn button.\nVerify exclusion completed successfully on the existing network controller per that documentation",
+		"inclusion": "In the UI, press the learn button. When prompted, enter the 5 digit underlined portion of the DSK code.",
+		"exclusion": "In the UI, press the learn button.",
 		"reset": "In the UI, press Hard Reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3441/IOTAS%20Consumer%20Hub%20Manual.pdf"
 	}

package/config/devices/0x043d/pgd728f_zpu.json

@@ -33,8 +33,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Bring the DoorLock within direct range of your controller.\n2. Carefully remove the battery compartment cover. \n3. Put your Z-Wave controller into inclusion mode. \n4. Simply press the Program button to enter programming mode.\n5. Select '2HB' to enter hub action menu.\n6. Select 'AD' and wait doorlock to finish the inclusion",
-		"exclusion": "1. Make sure the DoorLock is powered on and located within direct\n range of your Z-Wave gateway controller .\n2. Put your Z-Wave controller into exclusion mode .\n3. Simply press the Program button to enter programming mode.\n4. Select '2HB' to enter hub action menu.\n5. Select 'DE' and wait doorlock to finish the exclusion",
-		"reset": "When your network's primary controller is missing or otherwise \ninoperable, you may need to reset the device to factory settings \nmanually. Tocomplete \nthe process, make sure your doorlock has not been synced tothe \nsmart phone, then press and hold the reset button at least 3 sec to \nreset the doorlock and Z-Wave module. Also, you can restore the \nlock to factory default settings while the lock is synching with the \nsmartphone.\nWhen executing factory reset, Z-Wave module will issue the following \ninstructions to smart home controller.\nGroup：\"LIFELINE\" group\nInstruction: DEVICE_RESET_LOCALLY_NOTIFICATION"
+		"inclusion": "1. Remove the battery compartment cover\n2. Press the Program button to enter programming mode\n3. Select '2HB' to enter hub action menu\n4. Select 'AD' and wait for inclusion to complete",
+		"exclusion": "1. Press the Program button to enter programming mode\n2. Select '2HB' to enter hub action menu\n3. Select 'DE' and wait for exclusion to complete",
+		"reset": "Press and hold the reset button for at least 3 seconds. Make sure the doorlock is not synced to a smartphone before resetting."
 	}
 }

package/config/devices/0x0447/sqr62101whz.json

@@ -21,9 +21,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "A. SmartStart inclusion: The feature assumes the gateway has implemented SmartStart. Users could use the APP of the gateway or the gateway camera to scan the QR code on device or on device package before powering on the device, and then when the device is powered on, it shall be automatically added to the gateway.\nB. Manual inclusion: When the gateway is in adding mode (please refer to the instruction of the Z-Wave gateway for the operations on gateway itself), press the program button 3 times within 1.5s (the interval between each press is less than 0.5s)",
-		"exclusion": "Exclusion from a Z-Wave network: When the gateway is in removing mode (please refer to the instruction of the Z-Wave gateway for the operations on gateway itself), press the program button 3 times within 1.5s (the interval between each press is less than 0.5s)",
-		"reset": "3x quick click +1 x press> 10 seconds",
+		"inclusion": "Press the program button 3 times within 1.5s (the interval between each press is less than 0.5s).",
+		"exclusion": "Press the program button 3 times within 1.5s (the interval between each press is less than 0.5s).",
+		"reset": "1. Press the program button 3 times quickly\n2. Press and hold the program button for more than 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3922/GDE77980%20Z-Wave%20plug%20user%20manual_English%20version.pdf"
 	}
 }

package/config/devices/0x044b/wp-02sf.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Add：It will trigger ADD/REMOVE after press the OPEN button for more than 5seconds. Try again if failed. Notice: The triggering will be activated after the PRESS stopped",
-		"exclusion": "B. Remove：It will trigger ADD/REMOVE after press the OPEN button for more than 5 seconds. Try again if failed. Notice: The triggering will be activated after the PRESS stopped",
-		"reset": "Support Device Locally Reset\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the OPEN button for more than 5 seconds then release.",
+		"exclusion": "Press the OPEN button for more than 5 seconds then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4027/WP-02SF%20202011.pdf"
 	}
 }

package/config/devices/0x044c/myot.json

@@ -68,8 +68,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds",
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
 		"manual": "https://www.myvirtuosohome.com/en/downloads/send/4-manuals/209-z-wave-interface-actuator-manual-opentherm-boilers.html"
 	}
 }

package/config/devices/0x044c/myot2.json

@@ -195,7 +195,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds"
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds."
 	}
 }

package/config/devices/0x044c/myot4.json

@@ -116,7 +116,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "By pressing the FUNCTIONS button for 8 seconds",
-		"exclusion": "By pressing the FUNCTIONS button for 8 seconds"
+		"inclusion": "Press and hold the FUNCTIONS button for 8 seconds.",
+		"exclusion": "Press and hold the FUNCTIONS button for 8 seconds."
 	}
 }

package/config/devices/0x044f/uvh1301.json

@@ -22,9 +22,6 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Select \"Join Network\" in the app to put the kitchen hub into learn mode to join another network",
-		"exclusion": "Same as Inclusion",
-		"reset": "Factory Reset is available through the Settings menu in the app",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4285/zwave%20manual%20fixed.pdf"
 	}
 }

package/config/devices/0x045a/WB04V.json

@@ -341,8 +341,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/config/devices/0x045a/WM25L.json

@@ -238,8 +238,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the user guide of hub to enter inclusion mode.\nPress and hold the Config Button more than 6s, enter Include Mode",
-		"exclusion": "Follow the user guide of hub to enter exclusion mode.\nPress and hold the Config Button more than 6s, enter Exclusion Mode",
-		"reset": "Press and hold the Config Button more than 10s. The Curtain will reset itself to factory default by sending a Device Reset Locally Notification to gateway when the button is released.\nNote:Please use this procedure only when the network primary controller is missing or otherwise inoperable"
+		"inclusion": "Press and hold the Config Button for more than 6 seconds",
+		"exclusion": "Press and hold the Config Button for more than 6 seconds",
+		"reset": "Press and hold the Config Button for more than 10 seconds"
 	}
 }

package/config/devices/0x045a/Z-TRV-V01.json

@@ -152,8 +152,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power on your TRV. \n2. Set your Z-Wave controller into add/inclusion mode.\n3. In 'OF' state, short press rotary plate three times unit this screen shows '--'.\n4. The screen will show 'PA' after few seconds, whick meant the inclusion is successful. And the signal icon will light on. Otherwise, the inclusion is failed, which you will need to repeat the process.",
-		"exclusion": "1. Power on your TRV. \n2. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n3. In 'OF' state, short press rotary plate three times unit this screen shows '--'.\n4. The screen will turn back to 'OF' after few seconds. which meant the exclusion is successful. The signal light turn off.",
-		"reset": "Use this procedure only in the event that the primary controller is lost or otherwise inoperable. \n1. In 'OF' state, hold rotary plate for at least 5 seconds and release when screen will blink 'OF'. When successful, the screen will show 'OF' in solid for 2 seconds then turn off."
+		"inclusion": "1. Power on the TRV\n2. When the display shows 'OF', quickly press the rotary plate three times until the screen shows '--'\n3. The screen will show 'PA' if inclusion is successful",
+		"exclusion": "1. Power on the TRV\n2. When the display shows 'OF', quickly press the rotary plate three times until the screen shows '--'\n3. The screen will return to 'OF' if exclusion is successful",
+		"reset": "When the display shows 'OF', press and hold the rotary plate for at least 5 seconds until the screen blinks 'OF'"
 	}
 }

package/config/devices/0x0460/qldm-0A101.json

@@ -0,0 +1,129 @@
+{
+	"manufacturer": "Shelly Europe Ltd.",
+	"manufacturerId": "0x0460",
+	"label": "QLDM-0A101",
+	"description": "Wave Dimmer",
+	"devices": [
+		{
+			"productType": "0x0001",
+			"productId": "0x0083"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	},
+	"paramInformation": [
+		{
+			"#": "1",
+			"$import": "templates/wave_template.json#switch_type",
+			"label": "SW1 Switch Type",
+			"defaultValue": 0
+		},
+		{
+			"#": "2",
+			"$import": "templates/wave_template.json#switch_type",
+			"label": "SW2 Switch Type",
+			"defaultValue": 0
+		},
+		{
+			"#": "131",
+			"$import": "~/templates/master_template.json#base_enable_disable",
+			"label": "Dual Button Mode SW1 & SW2"
+		},
+		{
+			"#": "7",
+			"$import": "templates/wave_template.json#detached_mode",
+			"label": "Detach O1 Output"
+		},
+		{
+			"#": "8",
+			"$import": "templates/wave_template.json#detached_mode",
+			"label": "Detach O2 Output"
+		},
+		{
+			"#": "17",
+			"$import": "~/templates/master_template.json#state_after_power_failure_prev_off",
+			"label": "O1: State After Power Failure"
+		},
+		{
+			"#": "19",
+			"$import": "templates/wave_template.json#auto_off_timer",
+			"label": "O1: Auto-Off Timer"
+		},
+		{
+			"#": "20",
+			"$import": "templates/wave_template.json#auto_on_timer",
+			"label": "O1: Auto-On Timer"
+		},
+		{
+			"#": "25",
+			"$import": "templates/wave_template.json#timer_unit",
+			"label": "O1: Auto-On/Off Timer Unit"
+		},
+		{
+			"#": "36",
+			"$import": "templates/wave_template.json#power_change_report_treshold",
+			"label": "O1: Power Change Report Threshold"
+		},
+		{
+			"#": "39",
+			"$import": "templates/wave_template.json#min_time_between_reports",
+			"label": "O1: Minimum Time Between Power Reports"
+		},
+		{
+			"#": "78",
+			"$import": "templates/wave_template.json#force_calibration",
+			"label": "Calibrate Device"
+		},
+		{
+			"#": "121",
+			"$import": "templates/wave_template.json#max_dimming_value",
+			"label": "O1: Maximum Dim Level"
+		},
+		{
+			"#": "123",
+			"$import": "templates/wave_template.json#min_dimming_value",
+			"label": "O1: Minimum Dim Level"
+		},
+		{
+			"#": "125",
+			"$import": "templates/wave_template.json#dimming_time",
+			"label": "O1: Dimming Time (Short Press)"
+		},
+		{
+			"#": "127",
+			"$import": "templates/wave_template.json#fade_rate",
+			"label": "O1: Fade Rate (Long Press)"
+		},
+		{
+			"#": "129",
+			"$import": "~/templates/master_template.json#base_1-99_nounit",
+			"label": "O1: Minimum Turn-On Brightness",
+			"defaultValue": 15
+		},
+		{
+			"#": "117",
+			"$import": "templates/wave_template.json#remote_reboot",
+			"label": "Remote Reboot"
+		},
+		{
+			"#": "201",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 1"
+		},
+		{
+			"#": "202",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 2"
+		},
+		{
+			"#": "203",
+			"$import": "templates/wave_template.json#serial_number",
+			"label": "Serial Number: Part 3"
+		}
+	],
+	"metadata": {
+		"$import": "templates/wave_template.json#default_metadata"
+	}
+}