@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x032b/zd2102-5.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For 'Inclusion' (adding to) a network: Put the Z-Wave™ network controller into 'inclusion' mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds",
-		"exclusion": "For 'Exclusion' (removing from) a network: Put the Z-Wave™ network controller into 'exclusion' mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the 'Device Reset Locally Notification' command and reset to the factory default condition. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Press the program switch.",
+		"exclusion": "Press the program switch for at least 1 second.",
+		"reset": "1. Trigger the rear cover switch to send the Alarm Report\n2. Trigger the reed switch (close & open) 5 times in 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2249/ZD%202102_10252013.pdf"
 	}
 }

package/config/devices/0x032c/sk-3003-06.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Remove the battery plastic separator or make sure battery level is normally, and Make sure the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
-		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
-		"reset": "The factory default settings are restored when the device is removed from the network.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.",
+		"exclusion": "Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.",
+		"reset": "The factory default settings are restored when the device is removed from the network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2663/Wireless_Door_Sensor_User_Manual_20171117.pdf"
 	}
 }

package/config/devices/0x032c/sk-3003-07.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the left side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
-		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
-		"reset": "The factory default settings are restored when the device is removed from the network or press and hold the Add/Remove button on\nthe left side of product excess 10 seconds.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Click the Add/Remove button on the left side of product triple times in 1.5 seconds.",
+		"exclusion": "Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.",
+		"reset": "Press and hold the Add/Remove button on the left side of product for more than 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2711/Wireless_PIR_User_Manual_20171031.pdf"
 	}
 }

package/config/devices/0x032c/sk-5005-02.json

@@ -26,7 +26,7 @@
 		}
 	],
 	"metadata": {
-		"reset": "1) Press and hold both \"On\" and \"Off\" key together for 2 seconds until LED indicator light on, release all key;\n2) Press and hold both \"Stop\" and \"SOS\" key together for 10 seconds, during hold time LED will blink off 0.5 second interval 2 seconds. After hold 10 seconds LED indicator light off, then release all keys, factory default is retrieve, LED indicator will flashes three times after restore factory default success.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Press and hold both 'On' and 'Off' keys together for 2 seconds until the LED indicator turns on, then release all keys\n2. Press and hold both 'Stop' and 'SOS' keys together for 10 seconds\n3. The LED will blink off at 0.5 second intervals during the hold time\n4. After holding for 10 seconds the LED indicator will turn off, then release all keys\n5. The LED indicator will flash three times to confirm successful factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2496/Wireless_Keyfob_User_Manual_20171112.pdf"
 	}
 }

package/config/devices/0x032d/bsl01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Add device mode (see a main controller's operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while inclusion process implement and light on 2 second after processing complete",
-		"exclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Remove device mode (see a main controller's operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while exclusion process implement and light on 2 second after processing complete",
-		"reset": "Smart Hidden Door Lock restores factory default automatically when the device is excluded.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Triple click the Z-Wave button on the Z-Wave module (inside lock body) within 1.5 seconds. The LED will flicker rapidly during inclusion and stay on for 2 seconds when complete.",
+		"exclusion": "Triple click the Z-Wave button on the Z-Wave module (inside lock body) within 1.5 seconds. The LED will flicker rapidly during exclusion and stay on for 2 seconds when complete.",
+		"reset": "The Smart Hidden Door Lock restores factory defaults automatically when the device is excluded.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2462/BENETEK_SL_EN_V4_Ed_5.pdf"
 	}
 }

package/config/devices/0x033f/asl-03.json

@@ -23,9 +23,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "In order to include the August Smart Lock on to a Z-Wave network the user will have to do the following:\n\n1. Open the August app\n\n2. Go to the Lock Settings screen\n\n3. Select Z-Wave Settings\n\n4. Select Add To A Z-Wave Network\n\n5. Put the controller into inclusion mode and select My Hub is in Inclusion Mode on the August app",
-		"exclusion": "In order to exclude the August Smart Lock from a Z-Wave network the user will have to do the following:\n1. Open the August app\n2. Go to the Lock Settings screen\n3. Select Z-Wave Settings\n4. Select Remove Z-Wave Device\n5. Put the controller into exclusion mode and select My Hub is in Exclusion Mode on the August app",
-		"reset": "In order to reset the August Smart Lock the user will have to do the following:\n\n1. Open the August app\n\n2. Go to the Lock Settings screen\n\n3. Select Z-Wave Settings\n\n4. Select Remove Z-Wave device\n\n5. Select My Hub Is No Longer Working\n\n6. Caution: Resetting a Z-Wave device without telling the hub can cause performance issues. Use this procedure only when the Z-Wave hub is missing or otherwise inoperable. \n\n7. Select Reset Z-Wave Device\n\n8. On the Reset Z-Wave Device? prompt select Reset",
+		"inclusion": "1. Open the August app\n2. Go to the Lock Settings screen\n3. Select 'Z-Wave Settings'\n4. Select 'Add To A Z-Wave Network'\n5. Select 'My Hub is in Inclusion Mode' on the August app",
+		"exclusion": "1. Open the August app\n2. Go to the Lock Settings screen\n3. Select 'Z-Wave Settings'\n4. Select 'Remove Z-Wave Device'\n5. Select 'My Hub is in Exclusion Mode' on the August app",
+		"reset": "1. Open the August app\n2. Go to the Lock Settings screen\n3. Select 'Z-Wave Settings'\n4. Select 'Remove Z-Wave device'\n5. Select 'My Hub Is No Longer Working'\n6. Select 'Reset Z-Wave Device'\n7. On the 'Reset Z-Wave Device?' prompt select Reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2624/August%20Z-Wave%20Required%20Documentation.pdf",
 		"comments": {
 			"level": "error",

package/config/devices/0x0349/estmk-z-wav.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Open the tab [Devices] in the homee app and press the plus icon [+] on the top right side. In order to add a Z-Wave device select the purple button and press [START] on the next screen",
-		"exclusion": "If you don't want to continue using a certain device it needs to be removed from homee. To do this go to the settings of the device you wish to remove by tapping on the pencil icon in the devices detail screen. \n\n\nThe button to remove the device is on the bottom of the screen. You have 60 seconds to activate the learn mode on the device you wish to remove after confirmation of the removal. Doing this will remove the device from the Z-Wave network and reset it to its factory default settings",
-		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee's icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
+		"inclusion": "1. Open the [Devices] tab in the homee app\n2. Press the plus icon [+] on the top right\n3. Select the purple button and press [START]",
+		"exclusion": "1. Go to device settings (tap pencil icon in device detail screen)\n2. Press the remove button at the bottom\n3. Activate learn mode on the device within 60 seconds",
+		"reset": "1. Open the homee settings (homee icon > gear icon)\n2. Navigate to [Cubes] > [Z-Wave]\n3. Select [Reset Cube] and confirm\n\nNote: This resets only the Z-Wave cube. Connected devices must be reset manually according to their manuals",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3630/V-2homee-anleitung-compressed.pdf"
 	}
 }

package/config/devices/0x0349/homee_0002.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee's icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
+		"reset": "1. Open the homee settings (homee icon > gear icon)\n2. Navigate to [Cubes] > [Z-Wave]\n3. Select [Reset Cube] and confirm\n\nNote: This resets only the Z-Wave cube. Connected devices must be reset manually according to their manuals",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3133/homee-anleitung.pdf"
 	}
 }

package/config/devices/0x034b/irm-03wl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1. Click 'Reset'\n2. Once the lock device is removed, iRemocon 'SYNC-LED' blinks slowly.\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Click 'Reset'. The iRemocon 'SYNC-LED' will blink slowly once the device is removed.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2789/mc-zw-nw-app-manual.pdf"
 	}
 }

package/config/devices/0x034c/kas-z10.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": " Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n Press for 1seconds, LED is turn on \n\n Open sensor will try inclusion for 15 seconds when button is released.\n\n If inclusion is successful, LED will blink 3 times with 100ms interval",
-		"exclusion": " Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n Press for 1seconds, LED is turn on \n\n Open sensor will try exclusion when button is released. \n\n If exclusion is successful, LED will blink 3 times with 100ms interval",
-		"reset": " Press & hold inclusion/Exclusion button during 5 seconds. \n\n LED turn on and LED turn off after 5sec \n\n Release Inclusion/Exclusion \n\n Factory reset will be done in 5 seconds and blink 5 times with 100ms interval \n\n※ Please use factory reset only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press and hold the inclusion/exclusion button for 1 second until LED turns on\n2. Release the button to start inclusion for 15 seconds\n3. LED blinks 3 times at 100ms intervals if inclusion is successful",
+		"exclusion": "1. Press and hold the inclusion/exclusion button for 1 second until LED turns on\n2. Release the button to start exclusion\n3. LED blinks 3 times at 100ms intervals if exclusion is successful",
+		"reset": "1. Press and hold the inclusion/exclusion button for 5 seconds until LED turns on and off\n2. Release the button\n3. Factory reset completes in 5 seconds with LED blinking 5 times at 100ms intervals",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2756/51226_KAS-Z10.pdf"
 	}
 }

package/config/devices/0x034c/kms-z10.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": " Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n Press for 1seconds, LED is turn on \n\n Open sensor will try inclusion for 15 seconds when button is released.\n\n If inclusion is successful, LED will blink 3 times with 100ms interval",
-		"exclusion": " Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n Press for 1seconds, LED is turn on \n\n Open sensor will try exclusion when button is released. \n\n If exclusion is successful, LED will blink 3 times with 100ms interval",
-		"reset": " Press & hold inclusion/Exclusion button during 5 seconds. \n\n LED turn on and LED turn off after 5sec \n\n Release Inclusion/Exclusion \n\n Factory reset will be done in 5 seconds and blink 5 times with 100ms interval \n\n※ Please use factory reset only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "* Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n* Press for 1seconds, LED is turn on \n\n* Open sensor will try inclusion for 15 seconds when button is released.\n\n* If inclusion is successful, LED will blink 3 times with 100ms interval",
+		"exclusion": "* Press & hold inclusion/Exclusion button during 1 seconds when Open Sensor is exclusion status \n\n* Press for 1seconds, LED is turn on \n\n* Open sensor will try exclusion when button is released. \n\n* If exclusion is successful, LED will blink 3 times with 100ms interval",
+		"reset": "* Press & hold inclusion/Exclusion button during 5 seconds. \n\n* LED turn on and LED turn off after 5sec \n\n* Release Inclusion/Exclusion \n\n* Factory reset will be done in 5 seconds and blink 5 times with 100ms interval \n\n※ Please use factory reset only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2749/51225_KMS-Z10.pdf"
 	}
 }

package/config/devices/0x034e/mtbas-100-wl.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To add the myTEM Radio Server or myTEM Smart Server into an existing network set the Controller of the existing network into inclusion mode than click on «Learn Mode» in the UI (for more informatino see manual)",
-		"exclusion": "To remove the myTEM Radio Server or myTEM Smart Server from an existing network set the Controller of the existing network into inclusion mode than click on «Learn Mode» in the UI (for more informatino see manual)",
-		"reset": "To reset Radio Server use myTEM ProgTool.\n1. Create or open a project\n2. Connect to Radio Server\n3. Start Z-Wave Manager\n4. Click <Reset network> button\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nFor more information see myTEM ProgTool manual.",
+		"inclusion": "Click on 'Learn Mode' in the UI.",
+		"exclusion": "Click on 'Learn Mode' in the UI.",
+		"reset": "1. Create or open a project in myTEM ProgTool\n2. Connect to Radio Server\n3. Start Z-Wave Manager\n4. Click 'Reset network' button",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3664/myTem%20Progtool-manual%20V%200.8%20en.pdf"
 	}
 }

package/config/devices/0x034e/mtrgb-100-wl.json

@@ -26,9 +26,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Inclusion (Add)\nTo include (Add) the device to a Z-Wave network, press the button four times in quick succession. When the device is in Add mode, the LED flashes green. When finished, the new status is:\nAdd: The LED lights up briefly in green\nRemove: The LED lights up briefly in red",
-		"exclusion": "Exclusion (Remove)\nTo exclude (Remove) the device from a Z-Wave network, press the button four times in quick succession. When the device is in Add mode, the LED flashes green. When finished, the new status is:\nAdd: The LED lights up briefly in green\nRemove: The LED lights up briefly in red",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the button four times in quick succession. The LED flashes green when in add mode and lights up briefly in green when successful.",
+		"exclusion": "Press the button four times in quick succession. The LED flashes green when in add mode and lights up briefly in red when successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3234/Operating_manual_myTEM_Radio_RGBW_en.pdf"
 	}
 }

package/config/devices/0x034f/pl2s0s10-zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Tap add device on your app, then back to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"exclusion": "Tap add device on your app, then back to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"reset": "Press the R button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps",
+		"inclusion": "1. Enter programming code and confirm\n2. Press 9 and confirm\n3. 2 long beeps indicate success, 3 short beeps indicate failure",
+		"exclusion": "1. Enter programming code and confirm\n2. Press 9 and confirm\n3. 2 long beeps indicate success, 3 short beeps indicate failure",
+		"reset": "Press the R button for more than 5 seconds until you hear 3 long beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2896/PL2S%20Z-wave%20User%20Guide-2.pdf"
 	}
 }

package/config/devices/0x0353/re6100.json

@@ -15,9 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Navigate to the Devices screen using the left side menu on the Touchpad. \n2. Touch the '+ Add' icon on the top right corner to start adding Z-Wave. \n3. Connect+ will start the addition process and the following messages will display on the right side of the screen. This may take only a few seconds, or up to a minute to complete if the Connect+ controller is busy. \n4. When the second message above is displayed, Connect+ is now ready to add the new device. Follow the new device's instructions to place it into inclusion mode. This is typically a button press.\n5. After putting the device into inclusion mode, the following message will display on the screen. Depending on the device and number of supported command\nclasses, this may take only a few seconds or up to a minute to complete.\n6. If inclusion is successful, Connect+ will begin a device interrogation and gather current device command class states. It may take several seconds to display current device status on the screen. By default, the device's initial name is set to the assigned node number within the Z-Wave network. The following is an example of a typical light switch device",
-		"exclusion": "1.On the Z-Wave device page on the Touchpad, touch the '- Remove' icon in the top right corner.\n2.Connect+ will start the removal process. Status messages will display on the right side of the screen, and follow similar steps to the Add process. You will be prompted to place the device into exclusion mode, which is typically a button press. Follow the device's instructions to place it into exclusion mode.\n3. If removal fails, try again until successful",
-		"reset": "Two types of Z-Wave reset are supported: soft reset and hard reset. Soft reset will only reboot the Z-Wave controller and will retain all your devices. Use this if you are experiencing persistent network issues to attempt to correct them. A hard reset will set the Z-Wave controller in Connect+ back to its factory default and all network devices will be cleared.\n\n1. Navigate to the Settings screen from the left side menu, or the Settings icon on the home screen on the Touchpad.\n2. In the Settings menu, touch the last item 'Panel' and enter your 4-digit security system PIN when prompted.\n3. In the next sub-menu, scroll down and select the 'Z-Wave' menu item.\n4. Select either 'Soft Reset' or 'Hard Reset'. You will see a confirmation message on the screen before performing the reset action.\n5. A hard reset typically takes 5-10 seconds to complete. A soft reset will take additional time to complete refreshing all devices on the network, approximately 30 seconds per enrolled device. On large networks this may take several minutes to complete before normal operation is expected to resume.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Navigate to Settings > Panel (enter PIN) > Z-Wave\n2. Select 'Hard Reset'\n3. Confirm the reset action",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3307/RE6100P%20Installation%20Manual%20Z-Wave%20(1).pdf"
 	}
 }

package/config/devices/0x0369/7440-mc-fs.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Start the adding process on the controller side\n\nOnce started, start the adding process on the Connectair module by pressing 3 times the Z-Wave button, located between the plus and the minus button, using the included tool.\n\nWhen added, the LED will turn off",
-		"exclusion": "Start the removing process on the controller side\nOnce started, put the device in \"learn mode\" by pressing 3 times on the Z-Wave button, located between the plus and the minus button, using the included tool.\nWhen removed, the LED will turn on",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable\n\nHold the Z-Wave button for about ten seconds\nIf it was included, the LED will turn back on when reset is done",
+		"inclusion": "1. Start inclusion\n2. Press the Z-Wave button 3 times (located between + and - buttons)\n3. The LED will turn off when added",
+		"exclusion": "1. Start exclusion\n2. Press the Z-Wave button 3 times\n3. The LED will turn on when removed",
+		"reset": "Hold the Z-Wave button for about 10 seconds. The LED will turn on when reset is complete",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2965/ICCVUG-120618-2329.pdf"
 	}
 }

package/config/devices/0x0369/cw7.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave Factory reset procedure\nThe 2KLIC controller has an option to factory reset which allows the system to return back to its default settings, the steps are given below:\n\nFrom the home page, click on the property\nClick the System status icon in the left menu\nClick the Smart controller card, which is the first card visible, to edit the smart controller settings\nGo to the Manage Z-Wave tab \nOpen the Advanced options\nFind the Reset card\nClick on the Reset button to start\nClick on the text input and type 'Confirm' in the box below\nThen click on the Confirm button\nYou will see \"The controller is resetting. Please wait. It could take up to 1 minute.\" message\nAnd then you will see \"The controller has been reset\", as soon as it is done resetting\nNow you have to start adding new devices to your controller and take all the necessary steps to get your system up and running.\n\nResetting this controller will leave your Z-Wave devices orphaned in the network. Please remove all Z-Wave devices before performing this reset procedure. If this controller is a part of another Z-Wave network, please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. From home page, click on the property\n2. Click System status icon in left menu\n3. Click Smart controller card\n4. Go to Manage Z-Wave tab > Advanced options\n5. Find Reset card and click Reset button\n6. Type 'Confirm' in the text box and click Confirm\n\nNote: This will orphan all Z-Wave devices. Remove all devices before resetting",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2972/INT-HDW-5401%20Connectair%20CC7%20Controller%20v1%20-%20User%20guide.pdf"
 	}
 }

package/config/devices/0x036f/sentinel_2_0.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, the factory reset operation will result in the nodes in your network being orphaned and it will be necessary after the execution of reset operation to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable. \n\nTo reset the controller, hold the reset button for 16 seconds. This will reset it to factory default.",
+		"reset": "Hold the reset button for 16 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3226/EUGENIO%20manuale%20inglese_v4.2.pdf"
 	}
 }

package/config/devices/0x0371/zwa060.json

@@ -0,0 +1,16 @@
+{
+	"manufacturer": "Aeotec Ltd.",
+	"manufacturerId": "0x0371",
+	"label": "ZWA060",
+	"description": "Z-Stick 10 Pro",
+	"devices": [
+		{
+			"productType": "0x0004",
+			"productId": "0x003c"
+		}
+	],
+	"firmwareVersion": {
+		"min": "0.0",
+		"max": "255.255"
+	}
+}

package/config/devices/0x037b/gkbc-3100z.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3803/GKBC-3100Z_Z-Wave%20Manual_20200226.pdf"
 	}
 }

package/config/devices/0x037b/gkdl-5000z.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3991/GKDL-5000Z_5100Z_Z-Wave%20Manual_20200826.pdf"
 	}
 }

package/config/devices/0x037b/gkdl-5100z.json

@@ -70,9 +70,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3952/GKDL-5100Z_Z-Wave%20Manual_20200808.pdf"
 	}
 }

package/config/devices/0x037b/gkw-1000z.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [5].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [5]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3191/GKW-1000Z%20Z-Wave%20Manual_English_201801211.pdf"
 	}
 }

package/config/devices/0x037b/gkw-2000.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [8][8].",
-		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [9][9].",
-		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor unit and press the [REG] button.\n2. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).\n3. Press the [*] button, then press [5].\n4. Press the [*] button, then press [2].\n5. Press the [#] button, then enter the Master PIN: [1][2][3][4] (default value).",
+		"inclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [8][8]",
+		"exclusion": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [9][9]",
+		"reset": "1. Ensure the door lock is open\n2. Open the battery cover and press the [REG] button\n3. Press [*] then [5]\n4. Press [*] then [2]",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3064/GKW-2000D%20Z-Wave%20Manual_20180807.pdf"
 	}
 }

package/config/devices/0x037c/pad07-3e.json

@@ -36,7 +36,7 @@
 		{
 			"#": "2",
 			"label": "LED Indication Mode",
-			"description": "1. show dimmer state：when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode：when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
+			"description": "1. show dimmer state: when dimmer is on, LED is on. when dimmer is off, LED is off. the default setting is show dimmer state.  2. show night mode: when dimmer is on, LED is off. when dimmer is off, LED is on.  3. one flash mode : when dimmer on/off state changes, LED will light on one second and then off",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -58,7 +58,7 @@
 		{
 			"#": "3",
 			"label": "External Switch Type",
-			"description": "1. one switch mode：only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode：s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode：s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
+			"description": "1. one switch mode: only s1 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  2. two switch mode: s1 and s2 can dim up the light bulb to brightest level, then dim down to darkest level, and so on…  3. up/down switch mode: s1 can only dim up the light bulb to brightest level, and s2 can only dim down to off",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -101,9 +101,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing Include button of PAD07 three times within 2 seconds will enter exclusion mode.\n3. Node ID has been excluded.",
-		"reset": "1. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press Include button of PAD07 again for 5 seconds.\n3. IDs are excluded.\n\n*Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Include button three times within 2 seconds",
+		"exclusion": "Press the Include button three times within 2 seconds",
+		"reset": "Press the Include button three times within 2 seconds. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2935/PAD07%20manual-20180426.pdf"
 	}
 }

package/config/devices/0x037c/psm08-3e.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing button once to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing button once to enter the exclusion mode",
-		"reset": "There is a button on PSM08.\n1. Pressing button for about 5 seconds.\n2. IDs are excluded and all settings will reset to factory default.\nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable",
+		"inclusion": "Press the button once",
+		"exclusion": "Press the button once",
+		"reset": "Press the button for about 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2940/PSM08_manual-20161103.pdf"
 	}
 }

package/config/devices/0x038e/tfw-01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "• To add the unit to the network, put the controller (purchased separately) into the pairing/add/inclusion mode and then press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash to indicate it's in the pairing mode. When the blue light goes solid, the unit has been included in the network. If the blue light is not illuminated, the unit is not part of a network",
-		"exclusion": "• To remove the unit from a network put the controller (purchased separately) into the pairing/removal/exclusion mode and then press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash and will go out when the device is removed from the network",
-		"reset": "• This device will perform a Z-Wave factory reset when the exclusion process stated above is followed. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash during pairing and turn solid when inclusion is complete.",
+		"exclusion": "Press and hold the inclusion/exclusion button on the side of the detector for at least 5 seconds. The blue light will begin to flash and go out when the device is removed.",
+		"reset": "This device will perform a factory reset when the exclusion process is followed.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2995/Wireless%20Detector%20Manual%20Rev%20H.pdf"
 	}
 }

package/config/devices/0x039a/INT-SMDWD-01.json

@@ -87,9 +87,9 @@
 	],
 	"metadata": {
 		"wakeup": "Press the button briefly",
-		"inclusion": "Press the button 3 times within 1.5s to enter inclusion mode.",
-		"exclusion": "Press the button 3 times within 1.5s",
-		"reset": "Press and hold the button for 10s until LED light is on, then release the button.",
+		"inclusion": "Press the button 3 times within 1.5 seconds",
+		"exclusion": "Press the button 3 times within 1.5 seconds",
+		"reset": "Press and hold the button for 10 seconds until LED turns on, then release the button",
 		"manual": "http://downloads.inteset.com/DoorSensorManualS2.pdf"
 	}
 }

package/config/devices/0x039a/INT-SMMD-N1.json

@@ -242,9 +242,9 @@
 	],
 	"metadata": {
 		"wakeup": "Press the button briefly",
-		"inclusion": "Press the button 3 times within 1.5s to enter inclusion mode.",
-		"exclusion": "Press the button 3 times within 1.5s",
-		"reset": "Press and hold the button for 10s until LED light is on, then release the button.",
+		"inclusion": "Press the button 3 times within 1.5 seconds",
+		"exclusion": "Press the button 3 times within 1.5 seconds",
+		"reset": "Press and hold the button for 10 seconds until LED turns on, then release the button",
 		"manual": "http://downloads.inteset.com/Motion2In1ManualS2.pdf"
 	}
 }

package/config/devices/0x039b/uzw4010tim2.json

@@ -15,7 +15,6 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "With the Factory Reset server method it is possible to clear TIM Box device list. This cause z-wave devices removal from mobile and STB application but not their reset. To complete device reset, it is necessary to reset all z-wave devices physically.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3781/IoTIM%20-%20Quick%20Guide.pdf"
 	}
 }

package/config/devices/0x0407/ls090wh.json

@@ -21,7 +21,7 @@
 	},
 	"metadata": {
 		"inclusion": "Inclusion\n\n1. Click '+' on the upper right corner\n\n2. Select 'Z-Wave'\n\n3. Choose 'Add'\n\n4. Waiting for the procedure to finish\n\n5. Select security level\n\n6. Input DSK code",
-		"exclusion": "Exclusion\n\n1. Choose device on homepage\n\n2. Select '...' on the upper right corner\n\n3. Choose ‘Remove'",
+		"exclusion": "Exclusion\n\n1. Choose device on homepage\n\n2. Select '...' on the upper right corner\n\n3. Choose 'Remove'",
 		"reset": "Factory Reset\n1. Click '+' on the upper right corner\n2. Select 'Z-Wave'\n3. Choose 'Reset'\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3644/Smart%20Station%20User%20Manual.pdf"
 	}

package/config/devices/0x040b/pgzng1-2adnas.json

@@ -15,9 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To add a Z-Wave Device:\n1. Click Pulse Devices, and then click Switches, Door Locks, Thermostats, Others.\nThe Z-Wave Devices list screen appears.\n2. Click Add.\n3. Click the Z-Wave device's 'include' button. If you are adding a Z-Wave device with S2 security to an in-home gateway model number PGZNG1 v2, a dialog will prompt you for the 5-digit DSK (Device Specific Key).\n4. Follow the instructions on the dialog:\na. Locate the 5-digit DSK on the Z-Wave device.\nb. Enter the 5-digit DSK.\nc. For assistance in locating the DSK, click the information (i) icon on the dialog.\nd.Press Continue.\n5. Click on the newly added Z-Wave device list item.\n6. In the Name field, enter a name for the Z-Wave device, and then click Save.",
-		"exclusion": "To remove a Z-Wave device, click on the device in the Z-Wave Devices list to open the Z-Wave Device Details screen. Click the Remove button",
-		"reset": "To reset the device, press and hold the reset button on the back of the unit for about 15 seconds. The unit will then restart.\n\nNote: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and re-add all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this\nCopyright © 2014-2018 ICN Acquisition, LLC. All rights reserved.\nprocedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold the reset button on the back of the unit for about 15 seconds until the unit restarts",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3665/Z-Wave%20Plus%20Guide%2009-23-19.pdf"
 	}
 }

package/config/devices/0x040d/zw100.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Open the App mCamviewZ+ and go to \"Home Settings\" > \"Camera settings\" > \"Admin\" > \"Z-Wave administrator\" page, click \"Z-Wave Reset\" will reset the Z-Wave Settings of the camera.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.",
+		"reset": "Open the App mCamviewZ+ and go to Home Settings > Camera settings > Admin > Z-Wave administrator page, then click Z-Wave Reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3072/ZW100%20Quick%20Install%20Guide%20AND%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x040d/zw300.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Tap \"add device\" on your app, then tap enter to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"exclusion": "Tap \"remove device\" on your app, then tap enter to lock.\nEnter programming code -> confirm -> Enter 9 -> confirm\nIf you hear 2 long beeps from your lock the programming was successful.\nIf you hear short 3 beeps from your lock you must start over again",
-		"reset": "Press the R button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Press Enter on the lock\n2. Enter programming code and confirm\n3. Enter 9 and confirm\n4. Two long beeps indicate successful programming, three short beeps indicate failure",
+		"exclusion": "1. Press Enter on the lock\n2. Enter programming code and confirm\n3. Enter 9 and confirm\n4. Two long beeps indicate successful programming, three short beeps indicate failure",
+		"reset": "Press and hold the R button for more than 5 seconds until you hear 3 long beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3074/ZW300%20Smartlock%20Manual_Sept2018%20v2.pdf"
 	}
 }

package/config/devices/0x040f/rs-zwirex1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Push the Learn mode button once. Wait about 15 seconds",
-		"exclusion": "Push Z-Wave Learn mode button once. Wait about 5 seconds",
-		"reset": "Push Z-wave Learn mode button for 5 seconds",
+		"inclusion": "Press the Learn mode button once",
+		"exclusion": "Press the Learn mode button once",
+		"reset": "Press and hold the Learn mode button for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3465/QuickGuide_ZWIREX1_0703.pdf"
 	}
 }

package/config/devices/0x041a/kp-sw-07.json

@@ -54,9 +54,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "• Connect the power supply. \n• Set the Z-Wave network main controller into learning mode. \n• Press and hold the button 1 (the red light flashes slowly) until the pink light flashes slowly and then release, the device sends the network k information (blue light flashes quickly). \n• After the network is successfully connected, the LED indicator of the device is steady blue, and the load is off by default.",
-		"exclusion": "• Power on the switch. \n• Set the Z-Wave network controller into the exclusion mode. \n• Long press the switch button 1 (Red LED blink slowly) when Pink LED indicator light blink slowly, release the button, then the device start to send out exclusion information(Blue LED indicator in quick blinking). \n• When exclusion successfully, LED display is steady blue, load is off.",
-		"reset": "Reset procedure will delete all information in the Z-Wave network or Z-Wave gateway, and will restore switch to factory default settings. \n• Make sure switch is powered. \n• Press and hold the Switch button 1 for 20 seconds. \n• Until the pink light is always on, release the button. \n Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Connect the power supply\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when successfully connected",
+		"exclusion": "1. Power on the switch\n2. Press and hold button 1 until the pink LED flashes slowly, then release (the blue LED flashes quickly)\n3. The LED will be steady blue when exclusion is successful",
+		"reset": "1. Ensure the switch is powered\n2. Press and hold button 1 for 20 seconds\n3. Release the button when the pink LED is always on",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3580/KP-SW-07user%20manual.pdf"
 	}
 }