@zwave-js/config 15.7.0 → 15.9.0

package/config/devices/0x015f/mh-s510.json

@@ -89,9 +89,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Set controller into ADD mode. Follow instructions provided by controller manufacturer.\n2. Press and hold any key on the panel for 8 seconds or 3 clicks in quick succession. \nNote: If the ADD is successful, all INDICATION LEDs on the panel will flash 4 times.",
-		"exclusion": "1. Set controller into REMOVE mode. Follow instructions provided by controller manufacturer.\n2. Press and hold any key on the panel for 8 seconds or 3 clicks in quick succession.\nNote: If the REMOVE is successful, all INDICATION LEDs on the panel will flash 4 times. The REMOVE will delete all association data.",
-		"reset": "Press 20 times of any button (the interval time of touching is less than 500 milliseconds and the relay will keep same state after continually touching more than five times) or exclude the device from Z-Wave network, the factory setting will be restored.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and hold any key on the panel for 8 seconds or click any key 3 times quickly. If successful, all INDICATION LEDs on the panel will flash 4 times.",
+		"exclusion": "Press and hold any key on the panel for 8 seconds or click any key 3 times quickly. If successful, all INDICATION LEDs on the panel will flash 4 times.",
+		"reset": "Press any button 20 times (the interval time of touching is less than 500 milliseconds and the relay will keep same state after continually touching more than five times).",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3674/MH%20S510%20user%20manual.pdf"
 	}
 }

package/config/devices/0x015f/mh4936.json

@@ -7,6 +7,10 @@
 		{
 			"productType": "0x8101",
 			"productId": "0x4936"
+		},
+		{
+			"productType": "0x8101",
+			"productId": "0x4a36"
 		}
 	],
 	"firmwareVersion": {

package/config/devices/0x015f/mh6-hp.json

@@ -27,8 +27,8 @@
 	},
 	"metadata": {
 		"inclusion": "In normal display, press & hold ^ button to enter interface for adding Z-Wave network. Before device added into network, '- - -' will display on the screen. Then press ^ once, device will enter learning mode to get a node ID. If adding is successful, a Node ID will display on the screen in a few seconds.",
-		"exclusion": "In normal display, press & hold ^ button to enter interface for removing of Z-Wave network. A Node ID will display on the screen. Then press ^ button once, '- - -' will display on the screen to show removal was successful",
-		"reset": "1、Remove the device from Z-Wave network can restore factory setting.\n2、Configure the parameter 10 in secret menu can restore the factory setting also. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"exclusion": "In normal display, press & hold ^ button to enter interface for removing of Z-Wave network. A Node ID will display on the screen. Then press ^ button once, '- - -' will display on the screen to show removal was successful.",
+		"reset": "Remove the device from Z-Wave network can restore factory setting.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3042/MH6-HP%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x015f/mh7h.json

@@ -122,9 +122,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device added into network, '- - -' will display on the screen. Then press S4 once, device will enter learning mode to get a node ID. If adding is succeed, a node ID will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.\n\nAfter adding, turn off the device and then turn it on. Now the device is ready to be operated by controller/ gateway in Z-Wave network.",
-		"exclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device removed from network, a Node ID will display on the screen. Then press S4 once. If removing is succeed, '- - -'will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.When removed, the device will restore its factory setting.",
-		"reset": "A parameter P18 in the secret menu can be used to restore factory setting locally. Please use this procedure only when the network primary controller is missing or otherwise inoperable. ; And a parameter FF can be used to restore the factory setting via Z-Wave",
+		"inclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device added into network, '- - -' will display on the screen. Then press S4 once, device will enter learning mode to get a node ID. If adding is successful, a node ID will display on the screen in a few seconds.",
+		"exclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device removed from network, a Node ID will display on the screen. Then press S4 once. If removing is successful, '- - -' will display on the screen in a few seconds.",
+		"reset": "Configure parameter P18 in the secret menu to restore factory setting locally.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2900/MH7H%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x016a/ft098-k55.json

@@ -278,9 +278,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times",
-		"reset": "Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.\nAfter the LED Bulb is excluded from network, it will be reset to factory default state.\nUse this procedure only in the event that your primary network controller is missing or inoperable",
+		"inclusion": "Press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on.",
+		"exclusion": "Press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.",
+		"reset": "Press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2607/Bulb%20manual.pdf"
 	}
 }

package/config/devices/0x016a/ft100.json

@@ -535,9 +535,9 @@
 		"mapBasicSet": "Binary Sensor"
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Z-Wave button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Z-Wave button that you can find in back of the product",
-		"reset": "Press and hold the Z-Wave button that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Z-Wave button on the back of the product.",
+		"exclusion": "Short press the Z-Wave button on the back of the product.",
+		"reset": "Press and hold the Z-Wave button on the back of the product for 20 seconds, then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2592/Oomi%20MultiSensor%20manual3.pdf"
 	}
 }

package/config/devices/0x016a/ft101.json

@@ -30,7 +30,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nFollowing the UI guidelines on Oomi Touch or on-screen instructions on PC host, click the \"Reset\" button to reset the Cube.",
+		"reset": "Following the UI guidelines on Oomi Touch or on-screen instructions on PC host, click the \"Reset\" button to reset the Cube.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2677/Oomi%20Cube%20manual%20-2.pdf"
 	}
 }

package/config/devices/0x016a/ft102.json

@@ -51,9 +51,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Let your primary Controller/gateway into Inclusion mode, then press once the \"Learn\" Button in the app of Touch.",
-		"exclusion": "Let your primary Controller/gateway into Exclusion mode, then press once the \"Learn\" Button in the app of Touch.",
-		"reset": "Press the \"Reset\" button in the app of Touch. This procedure only be used when the primary controller is missing or inoperable",
+		"inclusion": "Press once the \"Learn\" Button in the app of Touch.",
+		"exclusion": "Press once the \"Learn\" Button in the app of Touch.",
+		"reset": "Press the \"Reset\" button in the app of Touch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1613/Oomi%20Touch%20manual.pdf"
 	}
 }

package/config/devices/0x016a/ft111.json

@@ -478,9 +478,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the Action button on the product housing.",
+		"exclusion": "Short press the Action button on the product housing.",
+		"reset": "Press and hold the Action button on the product housing for 20 seconds, then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2765/Oomi%20In-Wall%20Dimmer%20manual%20(FT111-K)%20-%202.pdf"
 	}
 }

package/config/devices/0x016a/ft112.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action Button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action Button that you can find in back of the product",
-		"reset": "Press the Action Button once that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the product's Action Button on the back of the product.",
+		"exclusion": "Short press the product's Action Button on the back of the product.",
+		"reset": "Press the Action Button on the back of the product for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1616/Door%20Window%20Sensor%206%20manual.pdf"
 	}
 }

package/config/devices/0x016a/ft130-k.json

@@ -156,9 +156,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action button that you can find on the product's housing",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action button that you can find on the product's housing",
-		"reset": "Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable",
+		"inclusion": "Short press the product's Action button on the product's housing.",
+		"exclusion": "Short press the product's Action button on the product's housing.",
+		"reset": "Press and hold the Action button on the product's housing for 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2767/Oomi%20Mote%20manual.pdf"
 	}
 }

package/config/devices/0x016a/ufa01.json

@@ -172,9 +172,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, short press the product's Action Button that you can find in the back of the product",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, short press the product's Action Button that you can find in back of the product",
-		"reset": "Press and hold the Action Button that you can find in back of the product for at least 20 seconds and then release. This procedure should only be used when the primary controller is inoperable",
+		"inclusion": "Short press the product's Action Button on the back of the product.",
+		"exclusion": "Short press the product's Action Button on the back of the product.",
+		"reset": "Press and hold the Action Button on the back of the product for at least 20 seconds and then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3219/KASAIHOUCHIKIADAPTOR01%20product%20mamual.pdf"
 	}
 }

package/config/devices/0x016b/204063.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Important: Perform this operation with care. Use the reset procedure only when the primary controller is missing or inoperable. \n\n• To access the factory reset function, navigate to the Advanced Z-Wave tile.\n• Press these buttons on the remote in sequence: <332211>.\n• This will display hidden tiles in the tile list. Navigate to the Factory Reset tile.\n• Select/Press the System Reset option to initiate a factory reset of the controller.\n• A popup will be displayed to confirm your desire to reset.\n• The factory reset (reset dongle) button is used to recover the controller from situations that cannot be recovered from by normal means.\n• The factory reset button will:\n• Reset the controller\n• Obtain a new home ID if the old home ID was in the randomizing range\n• Remove all devices from the network (devices will need to be factory reset if they were not excluded properly before the reset.)\n• Designate the controller as the primary SUC/SIS controller\n• The status of the controller, after a factory reset, will change to Primary: SUC/SIS.\n• After performing the factory reset, the SAGE Home Automation controller will reboot.\n• You will have to reset the remote and pair is once again. To reset the remote hold down the Lights and Back buttons together for 15 seconds.",
+		"reset": "1. Navigate to the Advanced Z-Wave tile\n2. Press these buttons on the remote in sequence: <332211>\n3. Navigate to the Factory Reset tile\n4. Select the System Reset option\n5. Confirm the reset in the popup\n6. To reset the remote, hold down the Lights and Back buttons together for 15 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1422/SAGE%20Z-Wave%20Product%20Document.pdf"
 	}
 }

package/config/devices/0x017c/9601921000.json

@@ -16,9 +16,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "To add (inclusion) the device press and hold the button for 3-8 seconds. When pressing the button, the led will flash short and after 3 seconds when the led has a steady light release the button",
-		"exclusion": "To remove (exclusion) the device press and hold the button for 3-8 seconds. When pressing the button, the led will flash short and after 3 seconds when the led has a steady light release the button",
-		"reset": "Press the button for more than 10 seconds to reset the\ndevice to factory default settings. The led will be released\nafter the device reset to factory defaults has been\nperformed.\nPlease use this procedure only when the network primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press and hold the button for 3-8 seconds. The LED will flash briefly, then show steady light after 3 seconds - release the button when the LED shows steady light.",
+		"exclusion": "Press and hold the button for 3-8 seconds. The LED will flash briefly, then show steady light after 3 seconds - release the button when the LED shows steady light.",
+		"reset": "Press the button for more than 10 seconds. The LED will turn off after the device resets to factory defaults.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3270/0450000594_1913_IA_heatapp-repeaterS2_EbV_EN.pdf"
 	}
 }

package/config/devices/0x017e/tgfx-hub1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "To return the FlexHub to factory defaults, use a pin or paper clip to press the recessed Reset button for 15 seconds. Observe the marquee pattern on the LEDs indicating the factory default is complete.\nNote that if the FlexHub is the primary controller for your network, resetting it to factory defaults will result in the nodes in your network being orphaned. It will be necessary after the reset to exclude and re-include all of the nodes in the network. If the FlexHub is being used as a secondary controller in the network, return to factory defaults only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Use a pin or paper clip to press the recessed Reset button for 15 seconds. The LEDs will show a marquee pattern indicating the factory reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2567/FlexHub%20Installation.pdf"
 	}
 }

package/config/devices/0x017f/pwhub-wh01.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "The HUB does not have a master factory reset function that will reset all radios. However, it does support a reset for Z-Wave products. The HUBs Z-Wave controller is reset using the Z-Wave Controls interface located under the HUB's settings menu. Within the Z-Wave Controls interface is a \"Reset Z-Wave\" button which will remove all nodes and reset the Z-Wave radio.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Navigate to the HUB's settings menu and access the Z-Wave Controls interface. Press the \"Reset Z-Wave\" button to remove all nodes and reset the Z-Wave radio.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2169/zwave_usermanual_161012_hub2.pdf"
 	}
 }

package/config/devices/0x017f/wink_d_w_sensor.json

@@ -47,9 +47,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the instructions for your Z-Wave certified Controller to enter inclusion mode.\nWhen prompted by the Controller:\n1. For proper inclusion, bring the Door/Window Sensor within range of your Controller.\n2. Pull the battery tab on the backside of the sensor to power on, or remove then re-install the batteries. The LED light should blink",
-		"exclusion": "Follow the instructions for your Z-Wave certified Controller to enter exclusion mode. When prompted by the Controller:\n1. Press the sensor cover release button to remove the top cover, and be sure the sensor is powered on.\n2. Press the Connect Button next to the battery quickly 3 times in a row.\n\nThe LED indicator will flash five times indicating exclusion/disconnection",
-		"reset": "If needed, the Door/Window Sensor can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from the system:\n1. Remove the SENSOR COVER and confirm that your Door/Window Sensor is powered up.\n2. Press and hold the BUTTON for at least 10 seconds then release. A flashing light indicates a successful factory reset.\n3. The Door/Window Sensor's memory will be erased to factory settings",
+		"inclusion": "Pull the battery tab on the backside of the sensor, or remove then re-install the batteries. The LED will blink.",
+		"exclusion": "1. Remove the sensor cover\n2. Press the Connect Button next to the battery quickly 3 times in a row. The LED will flash five times indicating exclusion.",
+		"reset": "1. Remove the sensor cover and confirm the sensor is powered\n2. Press and hold the button for at least 10 seconds, then release. A flashing light indicates successful factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2494/Wink-Door-Sensor-Manual.pdf"
 	}
 }

package/config/devices/0x017f/wink_motion_sensor.json

@@ -143,9 +143,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Follow the instructions for your Z-Wave certified Controller to enter inclusion mode.\nWhen prompted by the Controller:\n1. For proper inclusion, bring the Motion Detector within range of your Controller.\n2. Pull the tab on the side of the sensor to power on, or remove then re-install the batteries.\nThe LED indicator will flash five times indicating inclusion",
-		"exclusion": "Follow the instructions for your Z-Wave certified Controller to enter exclusion mode. When prompted by the Controller:\n1. Remove the cover of the Motion Detector and be sure it is powered on.\n2. Press the Connect Button on the bottom of the device quickly 3 times in a row.\nThe LED Indicator will flash five times indicating exclusion/disconnection.",
-		"reset": "To disconnect from the Z-Wave Network and restore factory default settings:\n1. Remove the cover of the Motion Detector and be sure it is powered on.\n2. Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.\nOnly do this if the controller is disconnected or otherwise unreachable!",
+		"inclusion": "Pull the tab on the side of the sensor, or remove then re-install the batteries. The LED will flash five times indicating inclusion.",
+		"exclusion": "1. Remove the Motion Detector cover\n2. Press the Connect Button on the bottom quickly 3 times in a row. The LED will flash five times indicating exclusion.",
+		"reset": "1. Remove the Motion Detector cover\n2. Hold the Connect Button for 10 seconds until the LED blinks once, then release",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2482/wink-motion-manual.pdf"
 	}
 }

package/config/devices/0x018b/gcr-01s.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This must be done when the gas valve is closed. After doing inclusion action on controller, hold 5 seconds (-) button until hearing beep once and ‘P' is blinking on LCD",
-		"exclusion": "This must be done when the gas valve is closed. After doing exclusion action on controller, hold 5 seconds (-) button until hearing beep once and ‘P' is blinking on LCD",
-		"reset": "Please use this only when the primary controller is missing or otherwise disabled.\n\nThis must be done when the gas valve is closed. Hold 15 seconds (-) button till hearing beep once and ‘FS' is displayed on LCD",
+		"inclusion": "With the gas valve closed, hold the (-) button for 5 seconds until you hear one beep and 'P' blinks on the LCD.",
+		"exclusion": "With the gas valve closed, hold the (-) button for 5 seconds until you hear one beep and 'P' blinks on the LCD.",
+		"reset": "With the gas valve closed, hold the (-) button for 15 seconds until you hear one beep and 'FS' is displayed on the LCD.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1591/UPlus%20Gas%20Lock%20Manual.docx"
 	}
 }

package/config/devices/0x018b/gihg20.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- Run ‘ZW_SET_DEFAULT' in Setting, then click YES of UZB PoP UP\n- Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Run 'ZW_SET_DEFAULT' in Settings, then click YES in the popup.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1841/IoT%20허브%20설명서_20160629_review.pdf"
 	}
 }

package/config/devices/0x018b/gwg-02.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- Run ‘ZW_SET_DEFAULT' in Setting, then click YES of UZB PoP UP\n- Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n- If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Run 'ZW_SET_DEFAULT' in Settings, then click YES in the popup.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2384/GWG-02_User%20Manual_20170516.pdf"
 	}
 }

package/config/devices/0x018b/irhg-01.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "- This is the Z-Wave Set Default network operation and a confirmation message appears.\n\n\"If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\"",
+		"reset": "Perform the Z-Wave Set Default network operation and confirm in the popup message.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3290/IRHG-01_User_Manual_new.pdf"
 	}
 }

package/config/devices/0x018c/pm-b400zw-n.json

@@ -63,9 +63,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Plug",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Plug",
-		"reset": "Press the button on the Smart Plug for more than 10 seconds after you plug the Smart Plug into a power outlet will make a Exclusion in the network controller, while the flashing red button LED Smart Plug. And all the variables are initialized.\n\n※ Please use this procedure only in the event that the network primary \n controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Plug into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Plug into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "Plug the Smart Plug into a power outlet and press the button for more than 10 seconds. The red LED will flash and all variables will be initialized.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1870/PB-B400ZWN_Manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-105.json

@@ -61,9 +61,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nThe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3315/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-205.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nThe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3314/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018c/ssd-305.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip",
-		"exclusion": "After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip",
-		"reset": "With the device powered, press and hold the third button for 10 seconds.\nhe LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.\nAfter a few moments, the entire LED is blinking and the green LED stops flashing.\nPlease use the procedure only in the event thant the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during inclusion.",
+		"exclusion": "Plug the Smart Power Strip into a power outlet and press the button for more than 5 seconds. The red LED will flash during exclusion.",
+		"reset": "1. With the device powered, press and hold the third button for 10 seconds\n2. The LED will flash red after 5 seconds, turn green, then flash red again\n3. Release the button when the entire LED blinks and the green LED stops flashing",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3287/Light%20switch%20user%20manual.pdf"
 	}
 }

package/config/devices/0x018e/acgs-23zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n1. Insert the 3V CR123A Lithium battery into the battery compartment connecting the correct polarity as shown on the battery compartment lid.\n2. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n3. Within 1 second, press the Function Button 3 times. \n4. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n5.If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Glass Break Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n2. Within 1 second, press the Function Button 3 times and the Glass Break Detector will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n1. Remove the batteries of the Glass Break Detector first.\n2. Press and hold the Function Button. While holding the Function Button, power on the Glass Break Detector by re-inserting the batteries, wait for 10 seconds to factory reset.\n<NOTE>\n1. Factory resetting the Glass Break Detector will restore it to factory default settings (excluded from the Z-Wave network). The Z-Wave gateway or control panel will still keep its Z-Wave settings. Please refer to the gateway or control panel manual on how to remove the Glass Break Detector's Z-Wave settings.",
+		"inclusion": "Insert the 3V CR123A Lithium battery with correct polarity, then press the Function Button 3 times within 1 second.",
+		"exclusion": "Press the Function Button 3 times within 1 second. The Glass Break Detector will be removed from the Z-Wave network.",
+		"reset": "1. Remove the batteries from the Glass Break Detector\n2. Press and hold the Function Button\n3. While holding the Function Button, re-insert the batteries and wait for 10 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3240/ACGS-23ZW-(OTA)%2020190124%20S2認證.pdf"
 	}
 }

package/config/devices/0x018e/bx-32zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n - Insert the two 1.5V D-Cell alkaline batteries into the battery \n compartment connecting the correct polarity as shown on the\n battery compartment lid.\n - The Bellbox will emit a 2-tone beep.\n Put the Z-Wave gateway or control panel into Inclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n - Within 1.5 seconds, press the Function Button 3 times.\n - Refer to the operation manual of the Z-Wave Gateway or Control \n Panel to complete the adding process.\n - If the sensor has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the sensor is unable to be added into \n the current Z-Wave Gateway/Control Panel, please exclude it first \n (see Removing Device) before attempting to include it into the \n current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Bellbox must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n - Put the Z-Wave gateway or control panel into Exclusion mode \n (please refer to the Z-Wave gateway or control panel manual).\n - Within 1.5 seconds, press the Function Button 3 times and the \n Bellbox will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n - Press and hold the Function button of the Bellbox for 10 seconds to \n factory reset with all LED flashes once.\n <NOTE>\n Factory resetting the Bellbox will restore it to factory default \n settings (excluded from the Z-Wave network). The Z-Wave gateway \n or control panel will still keep its Z-Wave settings. Please refer to \n the gateway or control panel manual on how to remove the \n Bellbox's Z-Wave settings.",
+		"inclusion": "1. Insert two 1.5V D-Cell alkaline batteries with correct polarity\n2. The Bellbox will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Bellbox will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function button for 10 seconds. All LEDs will flash once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2156/BX-32ZW_20161229.docx"
 	}
 }

package/config/devices/0x018e/bx-35zw.json

@@ -55,9 +55,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Insert the two 1.5V D-Cell alkaline batteries into the battery \n compartment connecting the correct polarity as shown on the \n battery compartment lid.The Bellbox will emit a 2-tone beep.\n -Put the Z-Wave gateway or control panel into Inclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to the operation manual of the Z-Wave Gateway or Control \n Panel to complete the adding process.\n -If the sensor has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the sensor is unable to be added into the \n current Z-Wave Gateway/Control Panel, please exclude it first (see \n Removing Device) before attempting to include it into the current Z-\n Wave Gateway/Control Panel.",
-		"exclusion": "The Bellbox must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\n -Put the Z-Wave gateway or control panel into Exclusion mode (please \n refer to the Z-Wave gateway or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the Bellbox \n will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n -Press and hold the Function button of the Bellbox for 10 seconds to \n factory reset with all LED flashes once.\n<NOTE>\n -Factory resetting the Bellbox will restore it to factory default \n settings (excluded from the Z-Wave network). The Z-Wave gateway or \n control panel will still keep its Z-Wave settings. Please refer to the \n gateway or control panel manual on how to remove the Bellbox's Z-\n Wave settings.",
+		"inclusion": "1. Insert two 1.5V D-Cell alkaline batteries with correct polarity\n2. The Bellbox will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Bellbox will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function button for 10 seconds. All LEDs will flash once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2431/BX-35-ZW_20170508.pdf"
 	}
 }

package/config/devices/0x018e/clmt-1zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Plug in the AC Input cable into the socket to power on the Clamp \n Meter.\n -Put the Control Panel into Inclusion mode (please refer to the Z-\n Wave control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to the operation manual of Z-Wave Gateway or Control Panel \n to complete the adding process.\n -If the device has already been added (included) into another Z-Wave \n Gateway/Control Panel, or if the device is unable to be added into \n the current Z-Wave Gateway/Control Panel, try removing it first (see \n Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n -Put the Z-Wave Gateway or Control Panel into Exclusion mode \n (please refer to the Z-Wave or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the \n device will be removed from the Z-Wave network.",
-		"reset": "Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave Gateway or Control Panel is lost or otherwise inoperable.\n -Press and hold the Function Button of the device for 10 seconds to \n factory reset.",
+		"inclusion": "Plug the AC Input cable into the socket to power on the Clamp Meter, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2255/CLMT-1ZW%2020170301.docx"
 	}
 }

package/config/devices/0x018e/co-8zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n- Insert the 3 'AA' batteries into the battery compartment connecting the correct polarity as shown on the battery compartment lid. CO-8 will emit a 2-tone beep.\n- Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times. CO-8 will emit a 2-tone beep.\n- Refer to the operation manual of the Z-Wave gateway/Control panel to complete the learn-in process.\n- If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Carbon Monoxide Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n- Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times and the Carbon Monoxide Detector will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\n(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n- Remove the batteries of the Carbon Monoxide Detector first.\n- Press and hold the Test Button. While holding the Test Button, power on the Heat Detector by re-inserting the batteries, wait for 10 seconds to factory reset.",
+		"inclusion": "1. Insert 3 AA batteries into the battery compartment with correct polarity\n2. CO-8 will emit a 2-tone beep\n3. Press the Function Button 3 times within 1.5 seconds\n4. CO-8 will emit another 2-tone beep",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Carbon Monoxide Detector will be removed from the Z-Wave network.",
+		"reset": "1. Remove the batteries from the Carbon Monoxide Detector\n2. Press and hold the Test Button\n3. While holding the Test Button, re-insert the batteries\n4. Wait for 10 seconds to complete factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2075/CO-8ZW_20161109.docx"
 	}
 }

package/config/devices/0x018e/dc-15zw.json

@@ -22,9 +22,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Pull out the battery insulator.\n-The LED indicator will turn on briefly.\n-Put the Z-wave gateway or control panel into Inclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times.\n-Refer to the operation manual of the Z-wave gateway or control panel to complete the learn-in process.\n-Please press and release the Tamper Switch once, and activate the Door Contact once (open and close) after inclusion is completed to ensure the Gateway/Control Panel recognizes the current status of the Door Contact.\n-If the sensor has already been included (learnt) into another Z-wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-wave Gateway/Control Panel.",
-		"exclusion": "The Door Contact must be removed from existing Z-wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Door Contact will be removed from the Z-wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Door Contact for 10 seconds to factory reset.",
+		"inclusion": "1. Pull out the battery insulator\n2. The LED indicator will turn on briefly\n3. Press the Test Button 3 times within 1.5 seconds\n4. Press and release the Tamper Switch once\n5. Activate the Door Contact once (open and close)",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Door Contact will be removed from the Z-wave network.",
+		"reset": "Press and hold the Test Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1429/DC-15ZW_20150806.doc"
 	}
 }

package/config/devices/0x018e/dc-23zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Pull out the battery insulator; this will connect the battery to power on the Door Contact.\n\n2. Put the Z-Wave Gateway or Control Panel into Inclusion mode (Please refer to the Z-Wave Gateway or Control Panel manual).\n\n3. Press the Function button 3 times within 1.5 seconds.\n\n4. Refer to the operation manual of the Z-Wave Gateway or Control Panel to complete adding process.\n\n5. If the Door Contact has already been added (included) into another Z-Wave Gateway/Control Panel, or if the Door Contact is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel",
-		"exclusion": "1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n\n2. Within 1.5 seconds, press the Function Button 3 times and the Door Contact will be removed from the Z-Wave network",
-		"reset": "Press and hold the Function Button of the Door Contact for 10 seconds to factory reset (only use factory reset when network Control Panel/Gateway is missing or inoperable)",
+		"inclusion": "Pull out the battery insulator to power on the Door Contact, then press the Function button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The Door Contact will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2542/DC-23ZW%20Manual.pdf"
 	}
 }

package/config/devices/0x018e/emd-1zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n -Insert batteries to power on the E-meter.\n -Put the Z-Wave control panel into Inclusion mode (please refer to \n the Z-Wave control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times.\n -Refer to operation manual of the Z-Wave Gateway or Control Panel \n to complete the adding process.\nIf the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n -Put the Z-Wave Gateway or Control Panel into Exclusion mode \n (please refer to the Z-Wave or control panel manual).\n -Within 1.5 seconds, press the Function Button 3 times and the \n device will be removed from the Z-Wave network.",
-		"reset": "Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave Gateway or Control Panel is lost or otherwise inoperable.\n -Press and hold the Function Button of the device for 10 seconds to \n factory reset.",
+		"inclusion": "Insert batteries to power on the E-meter, then press the Function Button 3 times within 1.5 seconds.",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2251/EMD-1ZW%2020170218.pdf"
 	}
 }

package/config/devices/0x018e/hd-9zw.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n-Insert the 3 'AA' batteries into the battery compartment connecting the correct polarity as shown on the battery compartment lid.\n-HD-9 will emit a 2-tone beep.\n-Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times. HD-9 will emit a 2-tone beep.\n-Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.\n-If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.",
-		"exclusion": "The Heat Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.\nExclusion Mode\n-Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).\n-Within 1.5 seconds, press the Test Button 3 times and the Heat Detector will be removed from the Z-Wave network.",
-		"reset": "(Only use factory reset when network Control Panel/Gateway is missing or inoperable).\n-Press and hold the Test Button of the Heat Detector.\n-While holding the Test Button, power on the Heat Detector, wait for 10 seconds to factory reset.",
+		"inclusion": "1. Insert 3 AA batteries into the battery compartment with correct polarity\n2. HD-9 will emit a 2-tone beep\n3. Press the Test Button 3 times within 1.5 seconds\n4. HD-9 will emit another 2-tone beep",
+		"exclusion": "Press the Test Button 3 times within 1.5 seconds. The Heat Detector will be removed from the Z-Wave network.",
+		"reset": "1. Press and hold the Test Button\n2. While holding the Test Button, power on the Heat Detector\n3. Wait for 10 seconds to complete factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1427/HD-9ZW%2020150911.doc"
 	}
 }

package/config/devices/0x018e/ir-16zw.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.\n- Pull out the battery Insulator steadily.\n- The LED indicator will flash for 30 seconds (The PIR is warming up). During the warm up period, the PIR will not be activated. It is recommended that you stay away from the detection area during this time. After the warming period is over, the LED will turn off and the PIR will be ready for operation.\n- Put the Z-Wave control panel into Inclusion mode (please refer to the Z-Wave control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times.\n- Refer to the operation manual of the Z-Wave gateway or control panel to complete the adding process.\n- Please press and release the Tamper Switch once after inclusion is completed to ensure the Gateway/Control Panel recognizes the current Tamper condition.\n- If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).",
-		"exclusion": "The device must be removed from existing Z-Wave network before being added into another.\nExclusion Mode\n- Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave or control panel manual).\n- Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-Wave network.",
-		"reset": "Factory Reset\nFactory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave gateway or control panel is lost or otherwise inoperable.\n- Press and hold the Function Button of the device for 12 seconds to factory reset.",
+		"inclusion": "1. Pull out the battery insulator\n2. The LED will flash for 30 seconds while the PIR warms up\n3. After the LED turns off, press the Function Button 3 times within 1.5 seconds\n4. Press and release the Tamper Switch once after inclusion",
+		"exclusion": "Press the Function Button 3 times within 1.5 seconds. The device will be removed from the Z-Wave network.",
+		"reset": "Press and hold the Function Button for 12 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2076/IR-16SLZW_IRP-16SLZW_20161109.doc"
 	}
 }