@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x013c/psr03-b.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered add mode.\n2. Press the key three times within 1.5 seconds to enter the add mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave ™ Controller about 20 seconds",
-		"exclusion": "1. Have Z-Wave ™ Controller entered remove mode.\n2. Press the key three times within 1.5 seconds to enter the \nremove mode.\nNode ID has been excluded",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Press the key three times,and do not release the key in the 4 th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the keys. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are remove and all settings will reset to factory \ndefault",
+		"inclusion": "Press the key three times within 1.5 seconds.",
+		"exclusion": "Press the key three times within 1.5 seconds.",
+		"reset": "1. Press and hold the key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the key within 2 seconds after the LED turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1407/PSR03_ABC_version_Manual.pdf"
 	},
 	"compat": {

package/config/devices/0x013c/psr03-c.json

@@ -28,9 +28,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered add mode.\n2. Press the key three times within 1.5 seconds to enter the add mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave ™ Controller about 20 seconds",
-		"exclusion": "1. Have Z-Wave ™ Controller entered remove mode.\n2. Press the key three times within 1.5 seconds to enter the \nremove mode.\nNode ID has been excluded",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Press the key three times,and do not release the key in the 4 th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the keys. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are remove and all settings will reset to factory \ndefault",
+		"inclusion": "Press the key three times within 1.5 seconds.",
+		"exclusion": "Press the key three times within 1.5 seconds.",
+		"reset": "1. Press and hold the key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the key within 2 seconds after the LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1407/PSR03_ABC_version_Manual.pdf"
 	}
 }

package/config/devices/0x013c/psr07.json

@@ -63,9 +63,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered inclusion mode.\n2. Rotate to area A and then press button three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "1. Have Z-Wave™ Controller entered exclusion mode.\n2. Rotate to area A and then press button three times within 1.5 seconds to enter the exclusion mode. Node ID has been removed",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Rotate to area A and then press button four times within 1.5 seconds and do not release the button in the 4 th pressed, and the red LED will light ON.\n2. After the red LED goes out, release the button within 2 seconds.\n3. IDs are removed and all settings will reset to factory default",
+		"inclusion": "1. Rotate to area A\n2. Press the button three times within 1.5 seconds",
+		"exclusion": "1. Rotate to area A\n2. Press the button three times within 1.5 seconds",
+		"reset": "1. Rotate to area A\n2. Press and hold the button four times within 1.5 seconds, keeping it held on the 4th press until the red LED lights up\n3. Release the button within 2 seconds after the red LED turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1988/PSR07_UserManual.pdf"
 	}
 }

package/config/devices/0x013c/pst02-a-br.json

@@ -304,9 +304,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo add into a Z-Wave network: \n1. Have Z-Wave Controller entered inclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds",
-		"exclusion": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo remove the device from a Z-Wave network: \n1. Have Z-Wave Controller entered exclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.\nNode ID has been excluded",
-		"reset": "There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.\nTo reset the device: \nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are excluded and all settings will reset to factory default",
+		"inclusion": "Press any tamper key three times within 1.5 seconds.\nNote: There are two tamper keys - one on the back side and one on the front side.",
+		"exclusion": "Press any tamper key three times within 1.5 seconds.\nNote: There are two tamper keys - one on the back side and one on the front side.",
+		"reset": "1. Press and hold any tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off\nNote: There are two tamper keys - one on the back side and one on the front side.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2625/Manual.pdf"
 	}
 }

package/config/devices/0x013c/pst02a.json

@@ -299,8 +299,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, triple click tamper switch within 1.5 seconds",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, triple click tamper switch within 1.5 seconds",
-		"reset": "Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th  pressed, and the LED will light on. After 3 seconds the LED will turn off, after that within 2 seconds, release the tamper key. If successful, the LED will light on one second. Otherwise, the LED will flash once. IDs are excluded and all settings will reset to factory default."
+		"inclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"exclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off."
 	}
 }

package/config/devices/0x013c/pst02b.json

@@ -221,8 +221,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, triple click tamper switch within 1.5 seconds",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, triple click tamper switch within 1.5 seconds",
-		"reset": "Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th  pressed, and the LED will light on. After 3 seconds the LED will turn off, after that within 2 seconds, release the tamper key. If successful, the LED will light on one second. Otherwise, the LED will flash once. IDs are excluded and all settings will reset to factory default."
+		"inclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"exclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off."
 	}
 }

package/config/devices/0x014a/ddls2-zwave5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Network Inclusion\nThe Z-Wave Plus Smart Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode.\n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Smart Switch.\n2) Put your Z-Wave Plus Controller into add (inclusion) mode.\n3) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.\n4) The LED on the front of the unit will turn off if successful included into a network",
-		"exclusion": "Network Exclusion\n1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch",
-		"reset": "Factory Default\nThe Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2781/DDLS2-ZWAVE5_Prod_Rev02.pdf"
 	}
 }

package/config/devices/0x014a/dls-zwave5.json

@@ -22,9 +22,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "The Z-Wave Plus Decora Light Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. \n\n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Decora Light Switch.\n2) Locate the light switch desired to be used with the Z-Wave Plus Decora Light Switch.\n3) Put your Z-Wave Plus Controller into add (inclusion) mode.\n4) Press the inclusion button on the Z-Wave Plus Decora Light Switch. (Figure 1)\n5) The LED on the front of the unit will turn off if successfully included into a network.",
-		"exclusion": "1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Press the inclusion / exclusion button on the Z-Wave Plus Decora Light Switch.",
-		"reset": "The Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1. Locate the light switch desired to be used with the Light Switch.\n2. Press the inclusion button on the Light Switch.\n3. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Press the inclusion / exclusion button on the Light Switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2164/Ecolink%20Decora%20Light%20Switch%20Z-Wave%20Plus%20Manual.pdf"
 	}
 }

package/config/devices/0x014a/dtls2-zwave5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "The Z-Wave Plus Smart Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. \n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Smart Switch.\n2) Put your Z-Wave Plus Controller into add (inclusion) mode.\n3) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. \n4) The LED on the front of the unit will turn off if network inclusion is successful.",
-		"exclusion": "1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.\n3) The LED in front of the unit will blink steadily if the network exclusion is successful.",
-		"reset": "The Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when network inclusion occurs.",
+		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED in front of the unit will blink steadily when network exclusion occurs.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2863/DTLS2-ZWAVE5_Prod_Rev06.pdf"
 	}
 }

package/config/devices/0x014a/dwzwave2.json

@@ -40,9 +40,6 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Once the controller is in inclusion mode, either remove the battery isolation tab, OR insert the battery to power up the sensor",
-		"exclusion": "Once the controller is in exclusion mode, either remove the battery isolation tab, OR insert the battery to power up the sensor",
-		"reset": "To restore this sensor to factory default settings, follow the instructions in the manual to exclude this sensor from the Z-Wave network. Upon completion of removal from the network the sensor will restore itself to factory default settings automatically. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1498/D.W.%20Zwave%20Manual%20R1.04.docx"
 	}
 }

package/config/devices/0x014a/dwzwave25.json

@@ -32,9 +32,8 @@
 	},
 	"metadata": {
 		"wakeup": "Removing the top case from the sensor will put in device into a tampered mode in which the sensor will stay awake and able to receive messages.",
-		"inclusion": "1. Start by placing the controller into inclusion mode.\n2. Activate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor. When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.\n3. Test the sensor. Place the magnet next to the sensor to represent a closed position. If the LED flashes ONE TIME, it is successfully communicating on your Zwave network. If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the inclusion process.\nNotes: If you need to repeat the inclusion process, repeat STEP ONE above, then for STEP TWO you will need to simply remove the cover of the sensor, remove the battery for 10 seconds, reinsert the battery, and replace the sensor cover. This will re-enter the sensor in inclusion mode.",
-		"exclusion": "1. Start by placing the controller into exclusion mode.\n2. Remove the cover of the sensor, remove the battery for 10 seconds, reinsert the battery, and replace the sensor cover.",
-		"reset": "To restore this sensor to factory default settings, follow the instructions to exclude this sensor from the Z-Wave network. Upon completion of removal from the network the sensor will restore itself to factory default settings automatically.",
+		"inclusion": "1. Activate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor.\n2. When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.",
+		"exclusion": "1. Remove the cover of the sensor.\n2. Remove the battery for 10 seconds.\n3. Reinsert the battery and replace the sensor cover.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1498/D.W.%20Zwave%20Manual%20R1.04.docx"
 	}
 }

package/config/devices/0x014a/ff-zwave5-eco.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Adding Sensor\nA) Be sure that the Z-Wave Plus Controller you are using is compatible with the FireFighter™. \nB) Either mount or move the sensor as close as possible to the place in the building where the sensor is to be mounted in order that the new Z-Wave Plus node is added to the correct place in the mesh network routing tables. \nC) To add the sensor to an existing Z-Wave Plus network, follow the directions to put your Z-Wave Plus Controller into add (inclusion) mode. The FireFighter™ enters add and remove (inclusion/exclusion) mode on pressing the learn button for 1 second which is located on the PCB between the LED and the tamper switch. If the LED starts blinking continuously, the sensor has no node ID and was not successfully added, so start step C over again. \nD) If after 5 seconds the LED is not blinking, look on the Z-Wave Plus controller’s interface for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for removing the sensor from a Z-Wave Plus network, and then try adding the sensor again. If you are still having problems, you may need to add additional Z-Wave Plus listening devices in-between the controller and the sensor.",
-		"exclusion": "Removing Sensor\nA) Any sensor can be removed from any Z-Wave Plus network with any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into Z-Wave Plus exclusion mode.\nB) Press the learn button located near the LED and Tamper switch. If successfully removed from the Z-Wave Plus network, the sensor’s LED should blink continuously if successful.",
-		"reset": "Factory Default\n The FireFighter™ can be restored back to factory default settings which will remove its Z-Wave Plus node ID from the sensor (but not the controller) with the following steps. \nA) Put the battery into the sensor.\nB) Do not press the tamper switch.\nC) Hold the learn button down for 10 seconds until the LED turns RED.\nD) Release the learn button and wait for the sensor’s green LED to “breath” on and off continuously. The sensor is now ready to be added to a Z-Wave Plus network, and all settings have been restored.\n\nPlease use this procedure only when the network primary\ncontroller is missing or otherwise inoperable.",
+		"inclusion": "Press the learn button for 1 second which is located on the PCB between the LED and the tamper switch. If the LED starts blinking continuously, the sensor was not successfully added.",
+		"exclusion": "Press the learn button located near the LED and Tamper switch. The sensor's LED should blink continuously when removed.",
+		"reset": "1. Put the battery into the sensor.\n2. Do not press the tamper switch.\n3. Hold the learn button down for 10 seconds until the LED turns RED.\n4. Release the learn button and the sensor's green LED will 'breath' on and off continuously.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1827/1%20-%20Ecolink%20FireFighter%20Z-wave%20plus%20Manual%20(standard).pdf"
 	}
 }

package/config/devices/0x014a/flf-zwave5_r1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. \n\n1) Verify that the Z-Wave Plus controller you are using is compatible with the Flood Freeze sensor.\n2) Either mount or move the Flood Freeze sensor as close as possible to the location the sensor will remain. See installation section below.\n3) Put your Z-Wave Plus Controller into add (inclusion) mode. \n4) To add the sensor to an existing Z-Wave network, follow the directions to put your Z-Wave Controller into add (inclusion) mode. The Flood Freeze enters add and remove (inclusion/exclusion) when powered on (when battery is added). If the LED starts blinking continuously, the sensor has no node ID and was not successfully added, so start step C over again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails. \n5) If after 5 seconds the LED is not blinking, look on the Z-Wave controller’s interface for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for removing the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add additional Z-Wave listening devices in-between the controller and the sensor.",
-		"exclusion": "1) Any sensor can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n2) Open the Flood Freeze case and remove the battery for 1 seconds. Replace the battery and the controller should remove the device from the Z-Wave network.",
-		"reset": "The Flood Freeze sensor factory defaults on network exclusion. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\" - You may use wording of your own choosing as long as it effectively means the same thing",
+		"inclusion": "Power up the device to enter inclusion mode. If the LED starts blinking continuously, the sensor was not successfully added. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.",
+		"exclusion": "1. Open the Flood Freeze case and remove the battery for 1 seconds.\n2. Replace the battery.",
+		"reset": "The Flood Freeze sensor factory defaults on network exclusion.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2929/51557%20%20Z-Wave%20FLF%20H214104%20ZWAVE_Ver04.pdf"
 	}
 }

package/config/devices/0x014a/gdzw7-eco.json

@@ -70,9 +70,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Follow the instructions of the Z-Wave controller to put the Z-Wave controller into manual or classic Z-Wave inclusion mode.\n2. Locate and press the hub button on the device.\n3. When it is successfully added, the device will beep and blink green once.",
-		"exclusion": "1. Follow the Z-Wave controller's instructions on putting the Z-Wave controller into removal/exclusion mode.\n2. Locate and press the hub button.\n3. Device's status indicator will blink red and beep three times to indicate successful removal",
-		"reset": "Hold the reset button down for ten seconds. The status indicator will blink red while the reset button is pressed and will go out after ten seconds.\nThe device's status indicator will turn green when the reset operation is complete.",
+		"inclusion": "Locate and press the hub button on the device. The device will beep and blink green once when added.",
+		"exclusion": "Locate and press the hub button. Device's status indicator will blink red and beep three times when removed.",
+		"reset": "Hold the reset button down for ten seconds. The status indicator will blink red while the reset button is pressed and will go out after ten seconds. The device's status indicator will turn green when the reset operation is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/74/GarageDoorControllerUserManualV3.pdf"
 	}
 }

package/config/devices/0x014a/iszw7-eco.json

@@ -88,9 +88,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Adding to a Z-Wave Network (Classic Inclusion Method)\nMake sure the device has power. Press the Pair Button which is the smaller of the two buttons, and the device will enter classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the Green LED will blink two times every three seconds. When Classic inclusion times-out, the device will blink red and green",
-		"exclusion": "Removing a Sensor from a Z-Wave Network\nTo remove the device, place the controller into Remove or “Z-Wave Exclusion” mode. Press the smaller of the two buttons (Add/Test) following the same procedure to add for removal. Upon successful removal, the device’s red led will come on solid for 1 second. Note: Any Z-Wave Inclusion Controller can remove a Z-Wave device regardless of manufacturer or which network the device is currently added to.",
-		"reset": "Factory Default\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable. \nTo restore the device back to factory settings and remove it from any Z-Wave network. Hold the Pair button for 10 seconds. During the 10 seconds of continuing to hold the Add/Test button the green LED with flash, and after 10 seconds the red LED will come on solid for 1 second indicating that the factory default of the device has been successful, and the device is ready to add back into a Z-Wave network.",
+		"inclusion": "Press the Pair Button (the smaller of the two buttons). During inclusion mode, the Green LED will blink two times every three seconds. When inclusion times-out, the device will blink red and green.",
+		"exclusion": "Press the smaller of the two buttons (Add/Test). The device's red led will come on solid for 1 second when removed.",
+		"reset": "Hold the Pair button for 10 seconds. During the 10 seconds the green LED will flash, and after 10 seconds the red LED will come on solid for 1 second after factory reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4000/ISZW7-ECO%20-%20Operation%20Manual%20v9.pdf"
 	}
 }

package/config/devices/0x014a/sc-zwave5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "The Z-Wave Plus Siren must be added to a Z-Wave network prior to use. To include the siren in a network both the siren and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. \n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Siren.\n2) Locate the power outlet desired to be used with the Z-Wave Plus Siren.\n3) Put your Z-Wave Plus Controller into add (inclusion) mode. \n4) Plug in the Z-Wave Siren and verify a single beep sound is heard.\n5) The LED on the front of the unit will turn off if successful included into a network.",
-		"exclusion": "1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Unplug and re-plug in your Z-Wave Plus Siren. \n3) The device will play a long beep and the LED will begin to breathe if the device is successfully removed from the network.",
-		"reset": "The Z-Wave Plus Siren is automatically factory defaulted when removed from a Z-Wave network. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Locate the power outlet desired to be used with the Z-Wave Plus Siren.\n2. Plug in the Z-Wave Siren and verify a single beep sound is heard.\n3. The LED on the front of the unit will turn off when included.",
+		"exclusion": "1. Unplug and re-plug in your Z-Wave Plus Siren.\n2. The device will play a long beep and the LED will begin to breathe when removed.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1899/0%20-%20Ecolink%20Siren%20Z-Wave%20Plus%20Manual%20(standard).pdf"
 	}
 }

package/config/devices/0x014a/sdls2-zwave5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Network Inclusion\nThe Z-Wave Plus Smart Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode.\n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Smart Switch.\n2) Put your Z-Wave Plus Controller into add (inclusion) mode.\n3) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.\n4) The LED on the front of the unit will turn off if successful included into a network",
-		"exclusion": "Network Exclusion\n1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch",
-		"reset": "Factory Default\nThe Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off when included.",
+		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2783/SDLS2-ZWAVE5_Prod_Rev02.pdf"
 	}
 }

package/config/devices/0x014a/stls2-zwave5.json

@@ -15,9 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "The Z-Wave Plus Smart Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. \n1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Smart Switch.\n2) Put your Z-Wave Plus Controller into add (inclusion) mode.\n3) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.\n4) The LED on the front of the unit will turn off if network inclusion is successful.",
-		"exclusion": "1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.\n2) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.\n3) The LED in front of the unit will blink steadily if the network exclusion is successful.",
-		"reset": "The Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED on the front of the unit will turn off if network inclusion is successful.",
+		"exclusion": "Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. The LED in front of the unit will blink steadily if the network exclusion is successful.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2864/STLS2-ZWAVE5_Prod_Rev05.pdf"
 	}
 }

package/config/devices/0x014a/tstat-tbz500.json

@@ -703,9 +703,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions provided with your system for enrolling the thermostat.\n2. Press and hold the FAN button on the Thermostat until the screen changes to the Menu screen.\n3. Press the UP button until ZWAVE is shown in the Status Display line then press Select.\n4. INSTALL should be shown on the status line.\n5. When instructed by your system installation to add the thermostat to the network press the “Select” button to install. Wait until SUCCESS or FAILED is shown on thestatus display.\n6. Press Done on the Thermostat to exit the ZWAVE screen.\n7. Press Done on the Thermostat again to exit the Menu screen.\n8. Once enrolled on your system’s network, continue to follow the instructions provided to complete the enrollment and naming of the thermostat.\n9. The indicator should be shown on the Thermostat Main screen indicating the thermostat has successfully been enrolled into the Z-Wave network.",
-		"exclusion": "It may be necessary to remove and/or reinstall the thermostat from a Z-Wave network if the thermostat has been previously installed on another network. Follow the instructions supplied with your Z-Wave system to remove/uninstall a Z-Wave device. When the system instructs you to press and release the Z-Wave button on the thermostat, follow these steps:\n\n1. Press and hold the FAN button for 3 seconds until the Menu screen is displayed.\n2. Press the UP arrow button to scroll to the “ZWAVE” menu.\n3. Press “Select” to select the ZWAVE screen.\n4. The display will show “REMOVE” in the text line.\n5. Press “Select” to perform the remove action.\n6. “WAIT” will be displayed in the text line. The remove operation is in process.\n7. “SUCCESS” will be display when the thermostat has been excluded from the network.\n8. Press “Done” to exit back to the thermostat screen.\n9. Thermostat is now ready to be added to any Z-Wave network.",
-		"reset": "Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable. To reset the TBZ500’s Z-Wave parameters to Factory Settings (both Z-Wave and HVAC settings): 1. Remove power from the TBZ500. 2. Restore power to the TBZ500. 3. When “TBZ500” appears on the screen, hold down the MODE and FAN buttons at the same time. 4. Release the buttons when RESET appears on the Status Line. 5. Once the TBZ500 resets the Z-Wave and HVAC settings, a DONE confirmation message will appear on the screen before the thermostat self-reboots",
+		"inclusion": "1. Press and hold the FAN button on the Thermostat until the screen changes to the Menu screen.\n2. Press the UP button until ZWAVE is shown in the Status Display line then press Select.\n3. INSTALL should be shown on the status line.\n4. Press the 'Select' button to install.\n5. Press Done on the Thermostat to exit the ZWAVE screen.\n6. Press Done on the Thermostat again to exit the Menu screen.",
+		"exclusion": "1. Press and hold the FAN button for 3 seconds until the Menu screen is displayed.\n2. Press the UP arrow button to scroll to the 'ZWAVE' menu.\n3. Press 'Select' to select the ZWAVE screen.\n4. The display will show 'REMOVE' in the text line.\n5. Press 'Select' to perform the remove action.\n6. Press 'Done' to exit back to the thermostat screen.",
+		"reset": "1. Remove power from the TBZ500.\n2. Restore power to the TBZ500.\n3. When 'TBZ500' appears on the screen, hold down the MODE and FAN buttons at the same time.\n4. Release the buttons when RESET appears on the Status Line.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4093/TBZ500_manual_8_5x5_5_inch__SC_20210325.pdf"
 	}
 }

package/config/devices/0x014f/wf00z.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZF5201 to the controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZF5201 to the controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
 		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1590/10008416X4%20WF00Z-1%20Instructions.pdf"
 	}

package/config/devices/0x0150/smartthings_hub_2018.json

@@ -25,7 +25,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave factory reset\nTo reset your Hub's Z-Wave system to factory default settings, you must factory reset the entire Hub. You can factory reset your Hub with steps found below.\n\nNOTE: Resetting the Hub will restore factory settings. All device connections, automations, rules, configurations, and SmartApps associated with that Hub will be lost in the reset. All devices connected to your Hub will have to be reset or excluded before they can be reconnected. The steps for resetting and reconnecting each smart device differ. After resetting, you can visit our Things category, find the devices you wish to set up, and follow the guides provided. Remember that you will likely need to reset or “exclude” every device before connecting.\n\nA physical factory reset is only possible for the Hub v2 with firmware 17.11 and up. If you have a Hub v1 or a Hub with firmware below 17.11, you can reset your Hub by deleting the Location it is connected to with these steps instead. Need to check your Hub’s firmware version? Find out how here.\n\nFollow these instructions to reboot the Hub instead, without doing a full factory reset.\n\n \n\nTo factory reset the Hub:\nMake sure the Hub is plugged in with the included power and network cables\nPress and hold the red recessed button on the back of the Hub for 30 seconds. When the LED on the front switches from flashing yellow to solid yellow, release the button\nNote: If you do not release the button within a few seconds after the LED switches to solid yellow, the Hub may not begin the reset\nThe Hub will take 10-15 minutes to fully factory reset. Once the LEDs on the Hub turn solid green, you should then be able to connect your Hub again. If you lost your original 6-character Welcome Code or are encountering other problems, these articles may help",
+		"reset": "Z-Wave factory reset\nTo reset your Hub's Z-Wave system to factory default settings, you must factory reset the entire Hub. You can factory reset your Hub with steps found below.\n\nNOTE: Resetting the Hub will restore factory settings. All device connections, automations, rules, configurations, and SmartApps associated with that Hub will be lost in the reset. All devices connected to your Hub will have to be reset or excluded before they can be reconnected. The steps for resetting and reconnecting each smart device differ. After resetting, you can visit our Things category, find the devices you wish to set up, and follow the guides provided. Remember that you will likely need to reset or 'exclude' every device before connecting.\n\nA physical factory reset is only possible for the Hub v2 with firmware 17.11 and up. If you have a Hub v1 or a Hub with firmware below 17.11, you can reset your Hub by deleting the Location it is connected to with these steps instead. Need to check your Hub's firmware version? Find out how here.\n\nFollow these instructions to reboot the Hub instead, without doing a full factory reset.\n\n \n\nTo factory reset the Hub:\nMake sure the Hub is plugged in with the included power and network cables\nPress and hold the red recessed button on the back of the Hub for 30 seconds. When the LED on the front switches from flashing yellow to solid yellow, release the button\nNote: If you do not release the button within a few seconds after the LED switches to solid yellow, the Hub may not begin the reset\nThe Hub will take 10-15 minutes to fully factory reset. Once the LEDs on the Hub turn solid green, you should then be able to connect your Hub again. If you lost your original 6-character Welcome Code or are encountering other problems, these articles may help",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3171/V3%20Z-Wave%20Manual.pdf"
 	}
 }

package/config/devices/0x0150/smartthings_link.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave factory reset\nTo reset your Hub's Z-Wave system to factory\ndefault settings, you must factory reset the entire\nHub. You can factory reset your Hub with Remove\nDevice menu in SmartThings mobile app.\nNOTE : Resetting the Hub will restore factory\nsettings. All device connections, automations, rules,\nconfigurations associated with that Hub will be lost\nin the reset. All devices connected to your Hub will\nhave to be reset or excluded before they can be\nreconnected. The steps for resetting and\nreconnecting each smart device differ. After\nresetting, you can visit our Things category, find the\ndevices you wish to set up, and follow the guides\nprovided. Remember that you will likely need to\nreset or “exclude” every device before connecting",
+		"reset": "Z-Wave factory reset\nTo reset your Hub's Z-Wave system to factory\ndefault settings, you must factory reset the entire\nHub. You can factory reset your Hub with Remove\nDevice menu in SmartThings mobile app.\nNOTE : Resetting the Hub will restore factory\nsettings. All device connections, automations, rules,\nconfigurations associated with that Hub will be lost\nin the reset. All devices connected to your Hub will\nhave to be reset or excluded before they can be\nreconnected. The steps for resetting and\nreconnecting each smart device differ. After\nresetting, you can visit our Things category, find the\ndevices you wish to set up, and follow the guides\nprovided. Remember that you will likely need to\nreset or 'exclude' every device before connecting",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3692/Link_QSG_EU_3.2(en)_1028.pdf"
 	}
 }

package/config/devices/0x0151/sw-dws02n.json

@@ -16,7 +16,7 @@
 	},
 	"metadata": {
 		"inclusion": "First install\n1. Pull the exposed plastic tab from the sensor.\n2. Power on\n3. The Green LED indicator will be lit for one second to indicate a successful booting.\n4. It will blink one time every second while scanning the network.\n5. If network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you need to use magnet or tamper to trigger a Add (Inclusion) process, and then sensor will repeat steps from 3 to 4.",
-		"exclusion": "1. Remove device rear cover and pressing the tamper button three times within 2 seconds, green LED indicator should go “On” 0.5 second and enter exclusion mode.\n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove.",
+		"exclusion": "1. Remove device rear cover and pressing the tamper button three times within 2 seconds, green LED indicator should go 'On' 0.5 second and enter exclusion mode.\n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove.",
 		"reset": "1. Pressing the tamper button four times within 2 seconds (Figure 4) and do not release the tamper button in the 4th pressed, and the LED will turn ON.\n2. After over 3 seconds the Green LED indicator will turn OFF, then go auto Adding procedure.\n3. IDs are excluded and all settings will reset to factory default.\n4. Device begin auto Adding (Inclusion) mode.\nNote: Use this procedure only in the event that the primary controller is lost.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3166/SW-DWS02N%20QIG_20181115.pdf"
 	}

package/config/devices/0x0152/dmwv1.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. For proper inclusion, bring the Water Main Shut-Off to the final location where it will be used. * \n2. Follow the instructions for your Z-Wave controller to enter inclusion mode. \n3 Make sure the Water Main Shut-Off is powered on, and when prompted by your controller, press the “open/close” button quickly 3 times in a row. The LED will stop blinking and stay on continuously upon successful inclusion. \n*For non Z-Wave Plus networks, please consult the owner’s manual for your primary controller to determine the best method and location for adding the Water Main Shut-Off to your Z-Wave network",
-		"exclusion": "1. Follow the instructions for your Z-Wave certified Controller to enter exclusion mode. \n2. When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.",
-		"reset": "Press and hold the open/close button for at least 10 seconds then release. The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset. Beware that resetting your device will disconnect it from your system. Only do this if the controller is missing or otherwise unreachable!",
+		"inclusion": "1. For proper inclusion, bring the Water Main Shut-Off to the final location where it will be used. * \n2. Follow the instructions for your Z-Wave controller to enter inclusion mode. \n3 Make sure the Water Main Shut-Off is powered on, and when prompted by your controller, press the 'open/close' button quickly 3 times in a row. The LED will stop blinking and stay on continuously upon successful inclusion. \n*For non Z-Wave Plus networks, please consult the owner's manual for your primary controller to determine the best method and location for adding the Water Main Shut-Off to your Z-Wave network",
+		"exclusion": "1. Follow the instructions for your Z-Wave certified Controller to enter exclusion mode. \n2. When prompted, press the 'open/close' button on the Shut-Off quickly 3 times in a row.",
+		"reset": "Press and hold the open/close button for at least 10 seconds then release. The Shut-Off's memory will be erased to factory settings. A flashing light indicates a successful factory reset. Beware that resetting your device will disconnect it from your system. Only do this if the controller is missing or otherwise unreachable!",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2648/Dome%20Water%20Main%20Shut-Off%20Advanced%20Manual.pdf"
 	}
 }

package/config/devices/0x0156/cp04.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "To add a Z-Wave device to the panel network — as with all sensors and peripheral devices — follow the detailed installation instructions included with that particular device.\n\nTo access Z-Wave settings from the control panel, go to:\n\nMenu > Software Version > Installer Toolbox > Smart Home Devices > Z-Wave",
 		"exclusion": "To remove a Z-Wave device to the panel network — as with all sensors and peripheral devices — follow the detailed installation instructions included with that particular device.\n\nTo access Z-Wave settings from the control panel, go to:\n\nMenu > Software Version > Installer Toolbox > Smart Home Devices > Z-Wave",
-		"reset": "The SmartHub’s Z-Wave network can be reset to a default state, removing all Z-Wave devices in the process. Please use this procedure only when the network primary controller is missing or otherwise inoperable. To do this, follow these instructions from the settings tab:\n5.2\n1. 2. 3. 4. 5. 6.\nOn the “Support” page, touch “Software version” Enter the default installer PIN code (2203)\nSelect “Smart Home devices”\nSelect “Z-Wave”\nSelect “Reset controller”\nFollow the on-screen instructions to complete the operation",
+		"reset": "The SmartHub's Z-Wave network can be reset to a default state, removing all Z-Wave devices in the process. Please use this procedure only when the network primary controller is missing or otherwise inoperable. To do this, follow these instructions from the settings tab:\n5.2\n1. 2. 3. 4. 5. 6.\nOn the 'Support' page, touch 'Software version' Enter the default installer PIN code (2203)\nSelect 'Smart Home devices'\nSelect 'Z-Wave'\nSelect 'Reset controller'\nFollow the on-screen instructions to complete the operation",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3113/SmartHubZwaveManual%20181025.pdf"
 	}
 }

package/config/devices/0x0156/ev2.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Set your panel to add node mode to add the thermostat as a node on your network.\n2. The Thermostat main screen shows a welcome message. Press the SIDE button to continue.\n3. When your panel is ready to connect to the Thermostat, press the SIDE button to connect. This initiates the network connection process. The Thermostat’s screen says “Connecting.”\n • If the connection fails, the screen says, “Failed.” Press the SIDE button to try connecting again.\n4. When the Thermostat has successfully joined a Z-Wave network from the panel, the screen displays the message “Next”.\n5. Complete your setup on the VIVINT panel.\n6. Press the SIDE button to continue.\n\nYour panel indicates that the thermostat was successfully added to its network (see your specific controller’s User Manual for details)",
-		"exclusion": "To get into Installer Settings, from the Home Screen, press and hold the SIDE button for three (3) seconds to access the SETTINGS menu.\n\nUse the UP/DN arrows to select the INSTALLER SETTINGS. Press the side button.\n\nUse the UP/DN arrows to select the NETWORK settings.\n\nIf the thermostat IS connected to the Z-Wave Network, “Disconnect” will be displayed. Press the SIDE button to\ndisconnect.",
+		"inclusion": "1. Set your panel to add node mode to add the thermostat as a node on your network.\n2. The Thermostat main screen shows a welcome message. Press the SIDE button to continue.\n3. When your panel is ready to connect to the Thermostat, press the SIDE button to connect. This initiates the network connection process. The Thermostat's screen says 'Connecting.'\n • If the connection fails, the screen says, 'Failed.' Press the SIDE button to try connecting again.\n4. When the Thermostat has successfully joined a Z-Wave network from the panel, the screen displays the message 'Next'.\n5. Complete your setup on the VIVINT panel.\n6. Press the SIDE button to continue.\n\nYour panel indicates that the thermostat was successfully added to its network (see your specific controller's User Manual for details)",
+		"exclusion": "To get into Installer Settings, from the Home Screen, press and hold the SIDE button for three (3) seconds to access the SETTINGS menu.\n\nUse the UP/DN arrows to select the INSTALLER SETTINGS. Press the side button.\n\nUse the UP/DN arrows to select the NETWORK settings.\n\nIf the thermostat IS connected to the Z-Wave Network, 'Disconnect' will be displayed. Press the SIDE button to\ndisconnect.",
 		"reset": "Reset will restore the thermostat settings to the factory defaults. It will also disconnect the thermostat from the\nZ-Wave network.\n1. Press the DOWN arrow to highlight Reset, then press the SIDE button.\n2. Confirm that you want to reset the thermostat, select yes, then press the SIDE button. The thermostat resets.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3702/Vivint%20Element_UM_feb_10_20.pdf"
 	}

package/config/devices/0x0156/m_n_kp01.json

@@ -101,7 +101,7 @@
 	"metadata": {
 		"inclusion": "Use this standard method for adding Z-Wave devices at the panel or hub. Use the \"PAIR/RESET\" button next to the battery tray. Follow the onscreen prompts to add the keypad.",
 		"exclusion": "Removing Keypad from System\nTo remove the device, place the panel Use this standard method for excluding Z-Wave devices at the panel or hub. Use the \"PAIR/RESET\" button next to the battery tray. Follow the onscreen prompts to add the keypad",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\nTo restore the keypad to factory settings which removes it from any network as well: \n1. Locate the button labeled Pair/Reset underneath the back battery cover. \n2. Insert a paperclip into the hole until you feel the button depress. \n3. Hold the button down for ten seconds. The green downcast indicator will blink rapidly while the reset button is pressed and go out after ten seconds. \n4. The device’s downcast indicator will turn red when the reset operation is complete. The device is now ready to be added back to a Z-Wave network.",
+		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\nTo restore the keypad to factory settings which removes it from any network as well: \n1. Locate the button labeled Pair/Reset underneath the back battery cover. \n2. Insert a paperclip into the hole until you feel the button depress. \n3. Hold the button down for ten seconds. The green downcast indicator will blink rapidly while the reset button is pressed and go out after ten seconds. \n4. The device's downcast indicator will turn red when the reset operation is complete. The device is now ready to be added back to a Z-Wave network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4119/Quick_Reference_Vivint_Keypad%20-%20DRAFT--%20for%20testing%20and%20review%20-%20working%20file%20Rev006.pdf"
 	}
 }

package/config/devices/0x0157/gr-105n.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "Press Button on the Valve-Control-Box three times rapidly (three times within 1.5 seconds). The red LED light will start blinking immediately (1 blink per second)",
 		"exclusion": "Press Button on the Valve-Control-Box three times rapidly (three times within 1.5 seconds). The red LED light will start blinking immediately (1 blink per second)",
-		"reset": "Press and hold the Button for 10 seconds to perform Local Reset procedure. Please use this procedure only when the network primary controller is missing or otherwise inoperable.”",
+		"reset": "Press and hold the Button for 10 seconds to perform Local Reset procedure. Please use this procedure only when the network primary controller is missing or otherwise inoperable.'",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2179/EVC200%20User's%20Guide-v3.pdf"
 	}
 }

package/config/devices/0x015b/ihu50.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Select ‘setDefault’ in [Command List]\n Click Send(Default) button.",
+		"reset": "Select ‘setDefault' in [Command List]\n Click Send(Default) button.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1457/APP%20Manual.pdf"
 	}
 }

package/config/devices/0x015d/zen20.json

@@ -253,7 +253,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to \n the Z-Wave network.\n2. Once the controller is ready to include your device, press up and release the toggle \n to include it in the network.\n3. Once your controller has confirmed that the device has been included, refresh the \n Z-Wave network to optimize performance.\n4. The device is associated in the same group when it included in setting process. \n Now you can control your Z-Wave device according to groups, scenes, schedules and automation programmed",
 		"exclusion": "1. Plug the power strip into a grounded receptacle located within 3 feet from your Z-Wave gateway controller\n\n2. Put your Z-Wave controller in exclusion mode\n\n3. Press and release the power button on the strip\n\n4. The device should disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the power strip into a grounded receptacle, then PRESS AND HOLD the power button for AT LEAST 3 SECONDS. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the power strip into a grounded receptacle, then PRESS AND HOLD the power button for AT LEAST 3 SECONDS. NOTE: All previously recorded activity and custom settings will be erased from the device's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1818/Zooz-Z-Wave-Power-Strip-Zen20-Manual.pdf"
 	}
 }

package/config/devices/0x015d/zen21.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "1. Bring your Z-Wave gateway hub or controller as close to the switch as possible\n2. Put your Z-Wave controller in inclusion mode\n3. Tap the switch on and off quickly 3 times to finalize the inclusion process\n4. A new on/off device should appear on your controller's device list\n\nTroubleshooting Tips:\nIf you are unable to include the Z-Wave switch to your controller, please try one of the following:\n- Bring the controller closer to your Z-Wave switch or use a hand-held secondary controller for inclusion\n- Tap your Z-Wave switch quicker 4 or 5 times once you put the controller in the inclusion mode to ensure the command has gone through\n- Put your controller in the EXCLUSION mode and tap the switch quickly 3 times, then try adding it to your network again",
 		"exclusion": "1. Bring your Z-Wave gateway hub or controller as close to the switch as possible\n2. Put your Z-Wave controller in exclusion mode\n3. Tap the switch on and off quickly 3 times to complete the exclusion process\n4. The device should disappear from your controller's device list\n\nPlease repeat the process following all steps carefully if the first attempt is unsuccessful",
-		"reset": "The switch will be reset to factory defaults only by exclusion using a Z-Wave controller. You may use any certified Z-Wave controller to exclude and reset the switch. This device may not be reset manually when the network’s primary controller is missing or otherwise inoperable. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"reset": "The switch will be reset to factory defaults only by exclusion using a Z-Wave controller. You may use any certified Z-Wave controller to exclude and reset the switch. This device may not be reset manually when the network's primary controller is missing or otherwise inoperable. NOTE: All previously recorded activity and custom settings will be erased from the device's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1945/zooz-z-wave-plus-on-off-switch-zen21-manual.pdf"
 	}
 }

package/config/devices/0x015f/a8-9.json

@@ -431,7 +431,7 @@
 	"metadata": {
 		"inclusion": "Activate Add mode in the gateway. When device is powered on, hold F1 to choose interface for Add into Z-Wave network. Click F2 five times until \"cycle icon\" turns blue. Hold F2 and the device enters into learning mode, then \"wifi icon\" turns blue and the device is added into Z-Wave network",
 		"exclusion": "Activate Remove mode in the gateway. When device is powered on, hold F1 to choose interface for Remove into Z-Wave network. Click F2 five times until \"cycle icon\" turns blue. Hold F2 and the device enters into learning mode, then \"wifi icon\" turns blue and the device is added into Z-Wave network",
-		"reset": "1. Remove the device from network.\n2. By manual: 1, Press & hold F1 to enter Z-Wave setting interface, then press & hold F1 again to enter parameters setting interface;\n2, Press & hold F2 to enter setting interface and select “default”;\n3, Click F2 3 times and displays “OFF”-->“ON”-->“OK”-->“OFF”, factory setting is restored.\n3. Input 0xFF to ==0x55 Restore factory setting\n ==0xAA Restore default para.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Remove the device from network.\n2. By manual: 1, Press & hold F1 to enter Z-Wave setting interface, then press & hold F1 again to enter parameters setting interface;\n2, Press & hold F2 to enter setting interface and select 'default';\n3, Click F2 3 times and displays 'OFF'-->'ON'-->'OK'-->'OFF', factory setting is restored.\n3. Input 0xFF to ==0x55 Restore factory setting\n ==0xAA Restore default para.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3456/A8-9.pdf"
 	}
 }

package/config/devices/0x015f/mh-p220.json

@@ -307,8 +307,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Add the device into Z-Wave network:\n1. Set controller into ADD mode. Follow the instructions provided by the controller/gateway manufacturer.\n2. Press the momentary button on the device 3 times, or the connected external button S1 3 times in quick succession. \nNote: If the ADD is successful, the INDICATION LED will blink 6 times. If not, INDICATION LED will be solid on or off depending on switch’s state.",
-		"exclusion": "Remove the device from Z-Wave network:\n1. Set controller into REMOVE mode. Follow the instructions provided by the controller/gateway manufacturer.\n2. Press the momentary button on the device 3 times, or the connected external button S1 3 times in quick succession. \nNote: If the REMOVE is successful, the INDICATION LED will blink 6 times. If not, INDICATION LED will be solid on or off depending on switch’s state.",
+		"inclusion": "Add the device into Z-Wave network:\n1. Set controller into ADD mode. Follow the instructions provided by the controller/gateway manufacturer.\n2. Press the momentary button on the device 3 times, or the connected external button S1 3 times in quick succession. \nNote: If the ADD is successful, the INDICATION LED will blink 6 times. If not, INDICATION LED will be solid on or off depending on switch's state.",
+		"exclusion": "Remove the device from Z-Wave network:\n1. Set controller into REMOVE mode. Follow the instructions provided by the controller/gateway manufacturer.\n2. Press the momentary button on the device 3 times, or the connected external button S1 3 times in quick succession. \nNote: If the REMOVE is successful, the INDICATION LED will blink 6 times. If not, INDICATION LED will be solid on or off depending on switch's state.",
 		"reset": "Restoring Factory Settings:\nThe default configuration can be restored by:\n Sending commands through controller/gateway (the command classes which support this function is Configuration Command Class). The parameter are as follows:\n\nParameter Number 0xFF\nSize 1 BYTE\nDefault value N/A\nConfiguration value 0x55\nSet 0xFF as 0x55 will restore Factory Settings.\n\n Or press the inner button on the module 10 times in quick succession.Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3011/MH-P220UserManual.pdf"
 	}

package/config/devices/0x015f/mh6-hp.json

@@ -26,8 +26,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "In normal display, press & hold ^ button to enter interface for adding Z-Wave network. Before device added into network, “- - -” will display on the screen. Then press ^ once, device will enter learning mode to get a node ID. If adding is successful, a Node ID will display on the screen in a few seconds.",
-		"exclusion": "In normal display, press & hold ^ button to enter interface for removing of Z-Wave network. A Node ID will display on the screen. Then press ^ button once, “- - -” will display on the screen to show removal was successful",
+		"inclusion": "In normal display, press & hold ^ button to enter interface for adding Z-Wave network. Before device added into network, '- - -' will display on the screen. Then press ^ once, device will enter learning mode to get a node ID. If adding is successful, a Node ID will display on the screen in a few seconds.",
+		"exclusion": "In normal display, press & hold ^ button to enter interface for removing of Z-Wave network. A Node ID will display on the screen. Then press ^ button once, '- - -' will display on the screen to show removal was successful",
 		"reset": "1、Remove the device from Z-Wave network can restore factory setting.\n2、Configure the parameter 10 in secret menu can restore the factory setting also. Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3042/MH6-HP%20User%20Manual.pdf"
 	}

package/config/devices/0x015f/mh7h.json

@@ -122,8 +122,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device added into network, “- - -” will display on the screen. Then press S4 once, device will enter learning mode to get a node ID. If adding is succeed, a node ID will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.\n\nAfter adding, turn off the device and then turn it on. Now the device is ready to be operated by controller/ gateway in Z-Wave network.",
-		"exclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device removed from network, a Node ID will display on the screen. Then press S4 once. If removing is succeed, “- - -”will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.When removed, the device will restore its factory setting.",
+		"inclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device added into network, '- - -' will display on the screen. Then press S4 once, device will enter learning mode to get a node ID. If adding is succeed, a node ID will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.\n\nAfter adding, turn off the device and then turn it on. Now the device is ready to be operated by controller/ gateway in Z-Wave network.",
+		"exclusion": "In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device removed from network, a Node ID will display on the screen. Then press S4 once. If removing is succeed, '- - -'will display on the screen in a few seconds. \n\nA node ID can always inform us whether the device is in the network or not.When removed, the device will restore its factory setting.",
 		"reset": "A parameter P18 in the secret menu can be used to restore factory setting locally. Please use this procedure only when the network primary controller is missing or otherwise inoperable. ; And a parameter FF can be used to restore the factory setting via Z-Wave",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2900/MH7H%20User%20Manual.pdf"
 	}

package/config/devices/0x0166/sw-zrc.json

@@ -269,7 +269,7 @@
 		}
 	],
 	"metadata": {
-		"reset": "1. Press and hold both the “Stop” and “All” keys until the red and green LEDs both start blinking at the same time (after about 3 seconds)\n2. Press three times (3x) on the “Up” command key of the RemSwiid™ remote and the blue Z-Wave LED will also light up. After about 2-3 seconds, the blue and red LEDs will turn off and the green LED will remain lit for 1-2 seconds indicating that the reset has been completed.\nResetting the RemSwiid™ remote will result in its taking on a new randomly generated Home ID. Obviously, if the RemSwiid™ remote is the primary controller in the Z-Wave network, resetting it will result in the nodes in the network being orphaned and it will be necessary after the reset to exclude and re-include all the nodes in a network with a new Home ID. If the RemSwiid™ is being used as a secondary controller in the network, the reset procedure should only be used once it has been excluded from the network, except of course if such exclusion is not feasible (e.g. if the network’s primary controller is missing or otherwise inoperable)",
+		"reset": "1. Press and hold both the 'Stop' and 'All' keys until the red and green LEDs both start blinking at the same time (after about 3 seconds)\n2. Press three times (3x) on the 'Up' command key of the RemSwiid™ remote and the blue Z-Wave LED will also light up. After about 2-3 seconds, the blue and red LEDs will turn off and the green LED will remain lit for 1-2 seconds indicating that the reset has been completed.\nResetting the RemSwiid™ remote will result in its taking on a new randomly generated Home ID. Obviously, if the RemSwiid™ remote is the primary controller in the Z-Wave network, resetting it will result in the nodes in the network being orphaned and it will be necessary after the reset to exclude and re-include all the nodes in a network with a new Home ID. If the RemSwiid™ is being used as a secondary controller in the network, the reset procedure should only be used once it has been excluded from the network, except of course if such exclusion is not feasible (e.g. if the network's primary controller is missing or otherwise inoperable)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2360/ZRC1%20Users%20manual%20v1.09%20CERTIFIED.pdf"
 	}
 }

package/config/devices/0x016a/ft098-k55.json

@@ -55,7 +55,7 @@
 		},
 		{
 			"#": "33",
-			"label": "Get the Bulb’s Color Value",
+			"label": "Get the Bulb's Color Value",
 			"valueSize": 4,
 			"defaultValue": 0,
 			"readOnly": true,
@@ -79,7 +79,7 @@
 		{
 			"#": "35",
 			"$import": "~/templates/master_template.json#base_enable_disable",
-			"label": "Use External Switch to Changes the Bulb’s Color",
+			"label": "Use External Switch to Changes the Bulb's Color",
 			"defaultValue": 1
 		},
 		{