@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x0330/sr-zv9001k2-dim.json

@@ -27,7 +27,7 @@
 	],
 	"metadata": {
 		"inclusion": "Step 1. Make sure the remote control does not belong to any Z-Wave network, short press any button, if LED indicator does not turn on, the remote control does not belong to any network, then continue step 2,if LED indicator turns on, it means the remote control has already been included to a network, please first set the remote control to exclusion mode (refer to the part \"Exclusion\" of this manual),then continue step 2.\nStep 2. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).\nStep 3. Press and hold down both two buttons over 3 seconds, LED indicator turns on, the remote control will be set to inclusion mode, and waiting to be included, after 10s LED indicator blinks 6 times quickly to indicate successful inclusion. The remote control is a sleepy device, after inclusion it will not enter into sleepy mode immediately, and will continue activation status for 30s and wait data interaction from the gateway, the LED indicator will stay solid on, please be patient to wait LED indicator to turn off",
-		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).\n2. Press and hold down both two buttons over 3 seconds, LED indicator turns on, the remote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times quickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part “Factory Reset” of this manual)",
+		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).\n2. Press and hold down both two buttons over 3 seconds, LED indicator turns on, the remote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times quickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part 'Factory Reset' of this manual)",
 		"reset": "Press and hold down both two buttons together for over 10 seconds, LED indicator turns on and then\nblinks 4 times quickly to indicate successful factory reset.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3900/SR-ZV9001K2-DIM%20Instruction.pdf"
 	}

package/config/devices/0x0330/sr-zv9001t3-dim.json

@@ -34,7 +34,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release “inclusion/exclusion” button, the wall controller will restart automatically.\n\nNote: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable",
+		"reset": "Press and hold down 'inclusion/exclusion' button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release 'inclusion/exclusion' button, the wall controller will restart automatically.\n\nNote: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2949/Z-Wave%20Wall%20Controller%20SR-ZV9001T3-DIM-US.pdf"
 	}
 }

package/config/devices/0x0330/sr-zv9001t4-dim.json

@@ -51,9 +51,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer to your primary\ncontrollers manual on how to turn your controller into inclusion).\n2. Make sure the wall controller does not belong to any Z-Wave network (please refer to\nthe part “How to check whether the wall controller included to a network” of this manual).\n3. Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF”\nbutton for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to\nbe included, then LED indicator turns on and blinks 6 times quickly to indicate\nsuccessful inclusion.\nOnce the wall controller quits “inclusion mode”, the LED indicator will turns off. There\nare 3 methods for the wall controller to quit “inclusion mode”:\n1. Automatically quits after successful inclusion.\n2. Quits after 25 seconds timeout.\n3. Press and hold down “ALL ON/OFF” button for over 3 seconds, or short press the\n“inclusion/exclusion” button to quit",
-		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary\ncontrollers manual on how to set your controller into exclusion).\n2. Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF”\nbutton for over 3 seconds, the wall controller will be set to exclusion mode, and waiting\nto be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to\nindicate successful exclusion.\nOnce the wall controller quits “exclusion mode”, the LED indicator will turns off. There\nare 3 methods for the wall controller to quit “exclusion mode”:\n1. Automatically quits after successful exclusion.\n2. Quits after 25 seconds timeout.\n3. Press and hold down “ALL ON/OFF” button for over 3 seconds, or short press the\n“inclusion/exclusion” button to quit.\nMethod 2: Factory reset the wall controller will force the wall controller to be excluded\nfrom a network. (please refer to the part “Factory Reset” of this manual)",
-		"reset": "Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful factory reset, release “inclusion/exclusion” button, the wall controller will restart automatically.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer to your primary\ncontrollers manual on how to turn your controller into inclusion).\n2. Make sure the wall controller does not belong to any Z-Wave network (please refer to\nthe part 'How to check whether the wall controller included to a network' of this manual).\n3. Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF'\nbutton for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to\nbe included, then LED indicator turns on and blinks 6 times quickly to indicate\nsuccessful inclusion.\nOnce the wall controller quits 'inclusion mode', the LED indicator will turns off. There\nare 3 methods for the wall controller to quit 'inclusion mode':\n1. Automatically quits after successful inclusion.\n2. Quits after 25 seconds timeout.\n3. Press and hold down 'ALL ON/OFF' button for over 3 seconds, or short press the\n'inclusion/exclusion' button to quit",
+		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary\ncontrollers manual on how to set your controller into exclusion).\n2. Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF'\nbutton for over 3 seconds, the wall controller will be set to exclusion mode, and waiting\nto be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to\nindicate successful exclusion.\nOnce the wall controller quits 'exclusion mode', the LED indicator will turns off. There\nare 3 methods for the wall controller to quit 'exclusion mode':\n1. Automatically quits after successful exclusion.\n2. Quits after 25 seconds timeout.\n3. Press and hold down 'ALL ON/OFF' button for over 3 seconds, or short press the\n'inclusion/exclusion' button to quit.\nMethod 2: Factory reset the wall controller will force the wall controller to be excluded\nfrom a network. (please refer to the part 'Factory Reset' of this manual)",
+		"reset": "Press and hold down 'inclusion/exclusion' button for over 8 seconds, LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful factory reset, release 'inclusion/exclusion' button, the wall controller will restart automatically.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2704/Z-Wave%20Wall%20Controller%20SR-ZV9001T4-DIM-EU%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x0330/sr-zv9002t3-cct.json

@@ -34,7 +34,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator will blink slowly to indicate successful factory reset, release “inclusion/exclusion” button,the wall controller will restart automatically.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold down 'inclusion/exclusion' button for over 8 seconds, LED indicator will blink slowly to indicate successful factory reset, release 'inclusion/exclusion' button,the wall controller will restart automatically.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2902/Z-Wave%20Wall%20Controller%20SR-ZV9002T3-CCT-US.pdf"
 	}
 }

package/config/devices/0x0330/sr-zv9092a.json

@@ -381,9 +381,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Adding to a Z-Wave Network (Inclusion)\nMethod 1: Select “Add”, then short press button , the device will send out inclusion request, “Status” will show “Inclusion...”. If there is no response from a gateway within 30 seconds, or inclusion failed, “Status” will show “Fail”. If included successfully, “Status” will show “Inclusion OK” and device ID.\nMethod 2: Operate the gateway into inclusion mode, make sure the device is already removed from previous network, reset power of the device, the device will be included to the gateway automatically",
-		"exclusion": "Removing from a Z-Wave Network (Exclusion)\nSelect “Remove”, then short press button , the device will send out exclusion request, “Status” will show “Exclusion...”. If there is no response from a gateway within 30 seconds, or exclusion failed, “Status” will show “Fail”. If excluded successfully, “Status” will show “Exclusion OK” and device ID will be showed as 0",
-		"reset": "Select “Reset”, then short press button F, the device will start reset, “Status” will show “Reset...”. If there is no response from a gateway within 6 seconds, or exclusion failed, “Status” will show “Fail”. If reset successfully, “Status” will show “Reset OK”",
+		"inclusion": "Adding to a Z-Wave Network (Inclusion)\nMethod 1: Select 'Add', then short press button , the device will send out inclusion request, 'Status' will show 'Inclusion...'. If there is no response from a gateway within 30 seconds, or inclusion failed, 'Status' will show 'Fail'. If included successfully, 'Status' will show 'Inclusion OK' and device ID.\nMethod 2: Operate the gateway into inclusion mode, make sure the device is already removed from previous network, reset power of the device, the device will be included to the gateway automatically",
+		"exclusion": "Removing from a Z-Wave Network (Exclusion)\nSelect 'Remove', then short press button , the device will send out exclusion request, 'Status' will show 'Exclusion...'. If there is no response from a gateway within 30 seconds, or exclusion failed, 'Status' will show 'Fail'. If excluded successfully, 'Status' will show 'Exclusion OK' and device ID will be showed as 0",
+		"reset": "Select 'Reset', then short press button F, the device will start reset, 'Status' will show 'Reset...'. If there is no response from a gateway within 6 seconds, or exclusion failed, 'Status' will show 'Fail'. If reset successfully, 'Status' will show 'Reset OK'",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4289/SR-ZV9092A%20instructionRelease.pdf"
 	}
 }

package/config/devices/0x0330/zv9001k12-dim-z4.json

@@ -26,7 +26,7 @@
 	},
 	"metadata": {
 		"inclusion": "Step 1. Make sure the remote control does not belong to any Z-Wave network, short press any button, if LED\nindicator does not turn on, the remote control does not belong to any network, then continue step 2,if LED\nindicator turns on, it means the remote control has already been included to a network, please first set the\nremote control to exclusion mode (refer to the part \"Exclusion\" of this manual),then continue step 2.\nStep 2. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on\nhow to turn your controller into inclusion).\nStep 3. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to inclusion mode, and waiting to be included, after 10s LED indicator blinks 6 times\nquickly to indicate successful inclusion. The remote control is a sleepy device, after inclusion it will not enter\ninto sleepy mode immediately, and will continue activation status for 30s and wait data interaction from the\ngateway, the LED indicator will stay solid on, please be patient to wait LED indicator to turn off",
-		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on\nhow to set your controller into exclusion).\n2. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times\nquickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part “Factory Reset” of this manual)",
+		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on\nhow to set your controller into exclusion).\n2. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times\nquickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part 'Factory Reset' of this manual)",
 		"reset": "Press and hold down both buttons All On I and All Off O for over 10 seconds, LED indicator turns on and then\nblinks 4 times quickly to indicate successful factory reset.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://www.sunricher.com/media/resources/manual/SR-ZV9001K12-DIM-Z4%20V2%20Instruction.pdf"
 	}

package/config/devices/0x0330/zv9001k12-dim-z5.json

@@ -23,7 +23,7 @@
 	},
 	"metadata": {
 		"inclusion": "Step 1. Make sure the remote control does not belong to any Z-Wave network, short press any button, if LED\nindicator does not turn on, the remote control does not belong to any network, then continue step 2,if LED\nindicator turns on, it means the remote control has already been included to a network, please first set the\nremote control to exclusion mode (refer to the part \"Exclusion\" of this manual),then continue step 2.\nStep 2. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on\nhow to turn your controller into inclusion).\nStep 3. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to inclusion mode, and waiting to be included, after 10s LED indicator blinks 6 times\nquickly to indicate successful inclusion. The remote control is a sleepy device, after inclusion it will not enter\ninto sleepy mode immediately, and will continue activation status for 30s and wait data interaction from the\ngateway, the LED indicator will stay solid on, please be patient to wait LED indicator to turn off",
-		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on\nhow to set your controller into exclusion).\n2. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times\nquickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part “Factory Reset” of this manual)",
+		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on\nhow to set your controller into exclusion).\n2. Press and hold down both buttons All On I and All Off O for over 3 seconds, LED indicator turns on, the\nremote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times\nquickly to indicate successful exclusion.\nMethod 2: Factory reset the remote control will force the remote control to be excluded from a network. (please refer to the part 'Factory Reset' of this manual)",
 		"reset": "Press and hold down both buttons All On I and All Off O for over 10 seconds, LED indicator turns on and then\nblinks 4 times quickly to indicate successful factory reset.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://www.sunricher.com/media/resources/manual/SR-ZV9001K12-DIM-Z5%20V2%20Instruction.pdf"
 	}

package/config/devices/0x0330/zv9001t-cct.json

@@ -20,9 +20,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF” button for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to be included, then LED indicator turns on and blinks 6 times quickly to indicate successful inclusion.",
-		"exclusion": "Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF” button for over 3 seconds, the wall controller will be set to exclusion mode, and waiting to be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful exclusion.",
-		"reset": "Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release “inclusion/exclusion” button, the wall controller will restart automatically.",
+		"inclusion": "Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF' button for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to be included, then LED indicator turns on and blinks 6 times quickly to indicate successful inclusion.",
+		"exclusion": "Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF' button for over 3 seconds, the wall controller will be set to exclusion mode, and waiting to be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful exclusion.",
+		"reset": "Press and hold down 'inclusion/exclusion' button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release 'inclusion/exclusion' button, the wall controller will restart automatically.",
 		"manual": "https://www.sunricher.com/media/resources/manual/SR-ZV9001T-CCT-EU%20Instruction.pdf"
 	}
 }

package/config/devices/0x0330/zv9003t-rgbw.json

@@ -20,9 +20,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF” button for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to be included, then LED indicator turns on and blinks 6 times quickly to indicate successful inclusion.",
-		"exclusion": "Short press the “inclusion/exclusion” button, or press and hold down “ALL ON/OFF” button for over 3 seconds, the wall controller will be set to exclusion mode, and waiting to be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful exclusion.",
-		"reset": "Press and hold down “inclusion/exclusion” button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release “inclusion/exclusion” button, the wall controller will restart automatically.",
+		"inclusion": "Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF' button for over 3 seconds, the wall controller will be set to inclusion mode, and waiting to be included, then LED indicator turns on and blinks 6 times quickly to indicate successful inclusion.",
+		"exclusion": "Short press the 'inclusion/exclusion' button, or press and hold down 'ALL ON/OFF' button for over 3 seconds, the wall controller will be set to exclusion mode, and waiting to be excluded, then LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful exclusion.",
+		"reset": "Press and hold down 'inclusion/exclusion' button for over 8 seconds, LED indicator blinks slowly to indicate successful factory reset, release 'inclusion/exclusion' button, the wall controller will restart automatically.",
 		"manual": "https://www.sunricher.com/media/resources/manual/SR-ZV9001T-RGBW-EU%20Instruction.pdf"
 	}
 }

package/config/devices/0x0333/th-gw10.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Described in Product manual “Parts Name”\n>Reset button\nPress and hold the button using a pen tip or like for 5 seconds or more.\nPressing and holding the button makes the all Volume indicators and Microphone mute indicators starts blinking. After blinking stops, release button. After that, the settings have been reverted back to the default.\nIf this controller is the primary controller of Z-Wave for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.\nIf this controller is being used as a secondary controller of Z-Wave in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
-		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2877/User’s%20Guide.pdf"
+		"reset": "Described in Product manual 'Parts Name'\n>Reset button\nPress and hold the button using a pen tip or like for 5 seconds or more.\nPressing and holding the button makes the all Volume indicators and Microphone mute indicators starts blinking. After blinking stops, release button. After that, the settings have been reverted back to the default.\nIf this controller is the primary controller of Z-Wave for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.\nIf this controller is being used as a secondary controller of Z-Wave in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2877/User's%20Guide.pdf"
 	}
 }

package/config/devices/0x0346/4aw1sz-0en0.json

@@ -114,8 +114,8 @@
 	],
 	"metadata": {
 		"inclusion": "Classic Inclusion Steps:\n1. Initiate add flow in the Ring Alarm mobile application – Follow the guided add flow instructions provided in the Ring Alarm Mobile application\n2. Select add manually and enter the 5 digit DSK pin found on the package of the Ring Alarm Retrofit Kit or the 5 digit DSK pin found on the inside of the top cover of the device.\n4. When the inclusion process in complete, the LED on the keypad will be solid green, then go out.\n\nSmart Start Inclusion Steps:\n1. Initiate add flow in the Ring Alarm mobile application – Follow the guided add flow instructions provided in the Ring Alarm Mobile application\n2. Scan the QR code found on the package of the Ring Alarm Retrofit Kit or the QR code found on the inside of the top cover of the device.\n4. When the inclusion process in complete, the LED on the keypad will be solid green, then go out",
-		"exclusion": "Exclusion Instructions:\n1. Initiate remove keypad flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device”\n2. Press and hold “1” key for three seconds\n3. When the exclusion process is complete, the LED on the keypad will be solid blue, then go out\n4. Test the Keypad. Any button presses would not beep",
-		"reset": "Ring Keypad – Reset\nFactory Default Instructions\n1. Press and hold “5” key and using a pointed end of a paperclip, gently press and release reset button via the reset pinhole found at the back of the keypad\n2. Red network LED at the top left-hand corner will start to blink rapidly\n3. Wait for the red LED to stop blinking then release the “5” key\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"exclusion": "Exclusion Instructions:\n1. Initiate remove keypad flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device'\n2. Press and hold '1' key for three seconds\n3. When the exclusion process is complete, the LED on the keypad will be solid blue, then go out\n4. Test the Keypad. Any button presses would not beep",
+		"reset": "Ring Keypad – Reset\nFactory Default Instructions\n1. Press and hold '5' key and using a pointed end of a paperclip, gently press and release reset button via the reset pinhole found at the back of the keypad\n2. Red network LED at the top left-hand corner will start to blink rapidly\n3. Wait for the red LED to stop blinking then release the '5' key\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3696/Ring%20Retrofit%20Alarm%20Kit%20ZWave.pdf"
 	}
 }

package/config/devices/0x0346/contact_sensor_gen2.json

@@ -103,7 +103,7 @@
 	],
 	"metadata": {
 		"inclusion": "After powering on the device, press and hold the button on the front of the device for ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times",
-		"exclusion": "Exclusion Instructions: \n1. Initiate remove “Ring Alarm Contact Sensor” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s red LED turns on solid to indicate the device was removed from the network.",
+		"exclusion": "Exclusion Instructions: \n1. Initiate remove 'Ring Alarm Contact Sensor' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device's red LED turns on solid to indicate the device was removed from the network.",
 		"reset": "Factory Default Instructions \n1. To restore Ring Alarm Contact Sensor to factory default settings, locate the pinhole reset button on the device. This is found inside the battery compartment on the back of the device after removing the back bracket. \n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds. \n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network. \n\nNote: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3862/Z-WaveUserManual_Contact_Sensor_700.pdf"
 	}

package/config/devices/0x0346/glass_break_sensor.json

@@ -214,7 +214,7 @@
 	],
 	"metadata": {
 		"inclusion": "Classic Inclusion Steps: \n1. Initiate add flow for Security Devices in the Ring mobile application – Follow the guided add flow instructions provided in the Ring mobile application.\n2. Select add manually and enter the 5-digit DSK pin found on the package of the Ring Alarm Glass Break Sensor or the 5-digit DSK pin found under the QR code on the device. \n3. After powering on the device, press and hold the setup button on the front for 3 seconds. Release the button and the device will enter Classic inclusion mode",
-		"exclusion": "Exclusion Instructions: \n1. Initiate remove “Ring Alarm Glass Break Sensor” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s red LED turns on solid to indicate the device was removed from the network",
+		"exclusion": "Exclusion Instructions: \n1. Initiate remove 'Ring Alarm Glass Break Sensor' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device's red LED turns on solid to indicate the device was removed from the network",
 		"reset": "Factory Default Instructions \n1. 1. To restore Ring Alarm Glass Break Sensor to factory default settings, locate the pinhole reset button on the device. This is found inside the battery compartment on the back of the device after removing the back bracket. \n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds. \n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network"
 	}
 }

package/config/devices/0x0346/keypad_v2.json

@@ -292,8 +292,8 @@
 	},
 	"metadata": {
 		"inclusion": "Classic Inclusion should be used if the controller does not support SmartStart.\n1. Initiate add flow for Security Devices in the Ring mobile application – Follow the guided add flow instructions provided in the Ring mobile application.\n2. Select add manually and enter the 5-digit DSK PIN found on the package of the Ring Alarm Keypad or the 5-digit DSK PIN found under the QR code on the device.\n3. After powering on the device, press and hold the #1 button for ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green Connection LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times",
-		"exclusion": "1. Initiate remove “Ring Alarm Keypad” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode.\n2. Locate the pinhole reset button on the back of the device.\n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s Connection LED turns on solid red to indicate the device was removed from the network.",
-		"reset": "Factory Default Instructions\n1. To restore Ring Alarm Keypad to factory default settings, locate the pinhole reset button on the device. This is found on the back of the device after removing the back bracket.\n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds.\n3. The device’s Connection icon LED will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network.\nNote\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"exclusion": "1. Initiate remove 'Ring Alarm Keypad' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode.\n2. Locate the pinhole reset button on the back of the device.\n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device's Connection LED turns on solid red to indicate the device was removed from the network.",
+		"reset": "Factory Default Instructions\n1. To restore Ring Alarm Keypad to factory default settings, locate the pinhole reset button on the device. This is found on the back of the device after removing the back bracket.\n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds.\n3. The device's Connection icon LED will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network.\nNote\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4150/Ring%20Alarm%20Keypad%20Zwave.pdf"
 	}
 }

package/config/devices/0x0346/motion_sensor_gen2.json

@@ -144,7 +144,7 @@
 	],
 	"metadata": {
 		"inclusion": "After powering on the device, press and hold the button on the front of the device for ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times",
-		"exclusion": "Exclusion Instructions: \n1. Initiate remove “Ring Alarm Motion Detector” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode. \n2. Locate the pinhole reset button on the back of the device in the battery compartment. \n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s red LED turns on solid to indicate the device was removed from the network.",
+		"exclusion": "Exclusion Instructions: \n1. Initiate remove 'Ring Alarm Motion Detector' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode. \n2. Locate the pinhole reset button on the back of the device in the battery compartment. \n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device's red LED turns on solid to indicate the device was removed from the network.",
 		"reset": "Factory Default Instructions \n1. To restore Ring Alarm Motion Detector to factory default settings, locate the pinhole reset button on the device. This is found inside the battery compartment on the back of the device after removing the back bracket. \n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds. \n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network. \n\nNote: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4149/Ring%20Alarm%20Motion%20Detector%20Zwave.pdf"
 	}

package/config/devices/0x0346/outdoor_contact_sensor.json

@@ -96,7 +96,7 @@
 	],
 	"metadata": {
 		"inclusion": "After powering on the device, press and hold the setup button for ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times.",
-		"exclusion": "Exclusion Instructions: \n1. Initiate remove “Ring Alarm Outdoor Contact Sensor” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole reset button. The device’s red LED turns on solid to indicate the device was removed from the network.",
+		"exclusion": "Exclusion Instructions: \n1. Initiate remove 'Ring Alarm Outdoor Contact Sensor' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode. \n2. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole reset button. The device's red LED turns on solid to indicate the device was removed from the network.",
 		"reset": "Factory Default Instructions \n1. To restore Ring Alarm Outdoor Contact Sensor to factory default settings, locate the pinhole reset button on the device. This is found on the back of the device after removing the mounting bracket. \n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds. \n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network. \n\nNote: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://support.ring.com/hc/en-us/article_attachments/4414661689748/Ring_Alarm_Outdoor_Contact_Sensor_Zwave.pdf"
 	}

package/config/devices/0x0346/range_extender_gen2.json

@@ -79,7 +79,7 @@
 	],
 	"metadata": {
 		"inclusion": "After powering on the device, press and hold the button on the front of the device for ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times",
-		"exclusion": "Exclusion Instructions:\n1. Initiate remove “Ring Alarm Range Extender” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose Remove Device to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode.\n2. Locate the pinhole reset button on the back of the device.\n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The\ndevice’s red LED turns on solid to indicate the device was removed from the network",
+		"exclusion": "Exclusion Instructions:\n1. Initiate remove 'Ring Alarm Range Extender' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose Remove Device to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode.\n2. Locate the pinhole reset button on the back of the device.\n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The\ndevice's red LED turns on solid to indicate the device was removed from the network",
 		"reset": "Factory Default Instructions\n1. To restore Ring Alarm Range Extender to factory default settings, locate the pinhole reset button on the device. This is found on the back of the device after unplugging the device from the outlet.\n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds.\n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops,\nrelease the button. The red LED will turn on solid to indicate the device was removed from the network.\nNote: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4148/Ring%20Alarm%20Range%20Extender%20Zwave.pdf"
 	}

package/config/devices/0x0346/ring_base_station.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Classic Inclusion Steps:\n1. Start inclusion mode on the primary controller \n2. From the application’s UI, navigate to controller’s device setting screen -> select Advance options -> Select Z-wave from “Protocol Adapters” and Select “Learn Mode” – DSK will be displayed (refer to the picture below)\n3. Select “Begin Learn Mode” in the UI\n4. When the inclusion process in complete, the LED on the base station will be solid blue\n\nNote: Joining another Z-Wave network via learn mode is available only when the base station is not already paired to any other devices",
-		"exclusion": "Exclusion Instructions:\n1. Start exclusion mode on the primary controller \n2. From the application’s UI, navigate to controller’s device setting screen -> select Advance options -> Select Z-wave from “Protocol Adapters” and Select “Learn Mode” – DSK will be displayed \n3. Select “Begin Learn Mode” in the UI\n4. When the exclusion process in complete, the LED on the base station will be solid blue",
-		"reset": "1. Launch Ring app (iOS or Android) \n2. Navigate to Base Station Setting: Devices à Alarm Base Station à Tap on gear icon located on top right-hand corner \n3. Navigate to Advanced Options à Z-Wave\n4. Tap “Reset Z-Wave Network” and Select “Reset” \nWarning: This process is irreversible. All your Z-Wave devices will be removed from your Base Station. You will have to manually reset and re-add each device to rebuild your network. \nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Classic Inclusion Steps:\n1. Start inclusion mode on the primary controller \n2. From the application's UI, navigate to controller's device setting screen -> select Advance options -> Select Z-wave from 'Protocol Adapters' and Select 'Learn Mode' – DSK will be displayed (refer to the picture below)\n3. Select 'Begin Learn Mode' in the UI\n4. When the inclusion process in complete, the LED on the base station will be solid blue\n\nNote: Joining another Z-Wave network via learn mode is available only when the base station is not already paired to any other devices",
+		"exclusion": "Exclusion Instructions:\n1. Start exclusion mode on the primary controller \n2. From the application's UI, navigate to controller's device setting screen -> select Advance options -> Select Z-wave from 'Protocol Adapters' and Select 'Learn Mode' – DSK will be displayed \n3. Select 'Begin Learn Mode' in the UI\n4. When the exclusion process in complete, the LED on the base station will be solid blue",
+		"reset": "1. Launch Ring app (iOS or Android) \n2. Navigate to Base Station Setting: Devices à Alarm Base Station à Tap on gear icon located on top right-hand corner \n3. Navigate to Advanced Options à Z-Wave\n4. Tap 'Reset Z-Wave Network' and Select 'Reset' \nWarning: This process is irreversible. All your Z-Wave devices will be removed from your Base Station. You will have to manually reset and re-add each device to rebuild your network. \nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4192/Base%20Station%20ZWave%20Technical%20Manual.pdf"
 	}
 }

package/config/devices/0x0346/ring_outdoor_siren.json

@@ -113,7 +113,7 @@
 	],
 	"metadata": {
 		"inclusion": "Classic Inclusion Steps: \n1. Initiate add flow for Security Devices in the Ring mobile application – Follow the guided add flow instructions provided in the Ring mobile application.\n2. Select add manually and enter the 5-digit DSK pin found on the package of the Ring Alarm Outdoor Siren or the 5-digit DSK pin found under the QR code on the device. \n3. After powering on the device, press and hold the test under the battery cover ~3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink three times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times",
-		"exclusion": "Exclusion Instructions: \n1. Initiate remove “Ring Alarm Outdoor Siren” flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose “Remove Device” to remove the device. This will place the controller into Remove or “Z-Wave Exclusion” mode. \n2. Locate the reset button on the back of the device under the battery compartment. \n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s red LED turns on solid to indicate the device was removed from the network.",
+		"exclusion": "Exclusion Instructions: \n1. Initiate remove 'Ring Alarm Outdoor Siren' flow in the Ring Alarm mobile application – Select the settings icon from device details page and choose 'Remove Device' to remove the device. This will place the controller into Remove or 'Z-Wave Exclusion' mode. \n2. Locate the reset button on the back of the device under the battery compartment. \n3. With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device's red LED turns on solid to indicate the device was removed from the network.",
 		"reset": "Factory Default Instructions \n1. To restore Ring Alarm Outdoor Siren to factory default settings, locate the reset button underneath the battery cover. \n2. Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds. \n3. The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was removed from the network. \nNote: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4118/Z-Wave%20User%20Manual_Outdoor_Siren.pdf"
 	}

package/config/devices/0x0348/chu00001-w.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Factory default Reset\nThe Central Home Unit can reset the Z-Wave network and it's device list. To do so open the Configuration User-Interface with the URL provided in the manual. Fill in your login credentials and confirm. This opens up the Management view of your Z-Wave network. In the Main Menu under the section \"More\" you can find the entry \"Reset network\". This will start the reset network operation. If success the device section will only show the controller device.\nPlease use this procedure only when the network is not working correctly.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Open the Configuration User Interface and log in. In the Main Menu under \"More\", select \"Reset network\" to start the reset operation.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2761/Manual_final_2.pdf"
 	}
 }

package/config/devices/0x0349/estmk-z-wav.json

@@ -16,8 +16,8 @@
 	},
 	"metadata": {
 		"inclusion": "Open the tab [Devices] in the homee app and press the plus icon [+] on the top right side. In order to add a Z-Wave device select the purple button and press [START] on the next screen",
-		"exclusion": "If you don’t want to continue using a certain device it needs to be removed from homee. To do this go to the settings of the device you wish to remove by tapping on the pencil icon in the devices detail screen. \n\n\nThe button to remove the device is on the bottom of the screen. You have 60 seconds to activate the learn mode on the device you wish to remove after confirmation of the removal. Doing this will remove the device from the Z-Wave network and reset it to its factory default settings",
-		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee’s icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
+		"exclusion": "If you don't want to continue using a certain device it needs to be removed from homee. To do this go to the settings of the device you wish to remove by tapping on the pencil icon in the devices detail screen. \n\n\nThe button to remove the device is on the bottom of the screen. You have 60 seconds to activate the learn mode on the device you wish to remove after confirmation of the removal. Doing this will remove the device from the Z-Wave network and reset it to its factory default settings",
+		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee's icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3630/V-2homee-anleitung-compressed.pdf"
 	}
 }

package/config/devices/0x0349/homee_0002.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee’s icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
+		"reset": "NOTE:❗If the Z-Wave cube is reset to factory defaults, all connected Z-Wave devices will be removed and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE:❗❗ This process does NOT reset the connected devices itself. They need to be reset manually following the manufacturers manual.\n\n\nTo reset the Z-Wave Cube to its factory defaults you need to open the general homee settings. They are reachable via your homee's icon in the top left corner and a subsequent press on the gear icon on the top right corner. Under the section [Cubes] > [Z-Wave] you can find all settings related to the Z-Wave cube. The menu entry [Reset Cube] resets the Z-Wave Cube back to its factory defaults after additional confirmation",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3133/homee-anleitung.pdf"
 	}
 }

package/config/devices/0x034b/irm-03wl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1. Click “Reset”\n2. Once the lock device is removed, iRemocon “SYNC-LED” blinks slowly.\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Click 'Reset'\n2. Once the lock device is removed, iRemocon 'SYNC-LED' blinks slowly.\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2789/mc-zw-nw-app-manual.pdf"
 	}
 }

package/config/devices/0x0353/re6100.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Navigate to the Devices screen using the left side menu on the Touchpad. \n2. Touch the “+ Add” icon on the top right corner to start adding Z-Wave. \n3. Connect+ will start the addition process and the following messages will display on the right side of the screen. This may take only a few seconds, or up to a minute to complete if the Connect+ controller is busy. \n4. When the second message above is displayed, Connect+ is now ready to add the new device. Follow the new device’s instructions to place it into inclusion mode. This is typically a button press.\n5. After putting the device into inclusion mode, the following message will display on the screen. Depending on the device and number of supported command\nclasses, this may take only a few seconds or up to a minute to complete.\n6. If inclusion is successful, Connect+ will begin a device interrogation and gather current device command class states. It may take several seconds to display current device status on the screen. By default, the device’s initial name is set to the assigned node number within the Z-Wave network. The following is an example of a typical light switch device",
-		"exclusion": "1.On the Z-Wave device page on the Touchpad, touch the “- Remove” icon in the top right corner.\n2.Connect+ will start the removal process. Status messages will display on the right side of the screen, and follow similar steps to the Add process. You will be prompted to place the device into exclusion mode, which is typically a button press. Follow the device’s instructions to place it into exclusion mode.\n3. If removal fails, try again until successful",
-		"reset": "Two types of Z-Wave reset are supported: soft reset and hard reset. Soft reset will only reboot the Z-Wave controller and will retain all your devices. Use this if you are experiencing persistent network issues to attempt to correct them. A hard reset will set the Z-Wave controller in Connect+ back to its factory default and all network devices will be cleared.\n\n1. Navigate to the Settings screen from the left side menu, or the Settings icon on the home screen on the Touchpad.\n2. In the Settings menu, touch the last item “Panel” and enter your 4-digit security system PIN when prompted.\n3. In the next sub-menu, scroll down and select the “Z-Wave” menu item.\n4. Select either “Soft Reset” or “Hard Reset”. You will see a confirmation message on the screen before performing the reset action.\n5. A hard reset typically takes 5-10 seconds to complete. A soft reset will take additional time to complete refreshing all devices on the network, approximately 30 seconds per enrolled device. On large networks this may take several minutes to complete before normal operation is expected to resume.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Navigate to the Devices screen using the left side menu on the Touchpad. \n2. Touch the '+ Add' icon on the top right corner to start adding Z-Wave. \n3. Connect+ will start the addition process and the following messages will display on the right side of the screen. This may take only a few seconds, or up to a minute to complete if the Connect+ controller is busy. \n4. When the second message above is displayed, Connect+ is now ready to add the new device. Follow the new device's instructions to place it into inclusion mode. This is typically a button press.\n5. After putting the device into inclusion mode, the following message will display on the screen. Depending on the device and number of supported command\nclasses, this may take only a few seconds or up to a minute to complete.\n6. If inclusion is successful, Connect+ will begin a device interrogation and gather current device command class states. It may take several seconds to display current device status on the screen. By default, the device's initial name is set to the assigned node number within the Z-Wave network. The following is an example of a typical light switch device",
+		"exclusion": "1.On the Z-Wave device page on the Touchpad, touch the '- Remove' icon in the top right corner.\n2.Connect+ will start the removal process. Status messages will display on the right side of the screen, and follow similar steps to the Add process. You will be prompted to place the device into exclusion mode, which is typically a button press. Follow the device's instructions to place it into exclusion mode.\n3. If removal fails, try again until successful",
+		"reset": "Two types of Z-Wave reset are supported: soft reset and hard reset. Soft reset will only reboot the Z-Wave controller and will retain all your devices. Use this if you are experiencing persistent network issues to attempt to correct them. A hard reset will set the Z-Wave controller in Connect+ back to its factory default and all network devices will be cleared.\n\n1. Navigate to the Settings screen from the left side menu, or the Settings icon on the home screen on the Touchpad.\n2. In the Settings menu, touch the last item 'Panel' and enter your 4-digit security system PIN when prompted.\n3. In the next sub-menu, scroll down and select the 'Z-Wave' menu item.\n4. Select either 'Soft Reset' or 'Hard Reset'. You will see a confirmation message on the screen before performing the reset action.\n5. A hard reset typically takes 5-10 seconds to complete. A soft reset will take additional time to complete refreshing all devices on the network, approximately 30 seconds per enrolled device. On large networks this may take several minutes to complete before normal operation is expected to resume.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3307/RE6100P%20Installation%20Manual%20Z-Wave%20(1).pdf"
 	}
 }

package/config/devices/0x0363/iotx-z-actmotor001.json

@@ -86,8 +86,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Make sure connecting module to power supply and module has not joined Z-Wave network (if module joined any other Z-Wave network, please refer to the clauses “Exclude device from a Z-Wave network”). \nFirst, set primary controller/gateway into inclusion mode. And press 'Button L' 3 times, LED starts to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success. If module does not find a Z-Wave network within 10 seconds after join network function trigger, please try again. After joined Z-Wave network, please wait for a while until the app showing device is included. Then you can start enjoying with our module",
-		"exclusion": "Method 1: Factory Reset.\nMethod 2: First, set primary controller/gateway into exclusion mode. And press 'Button L' 3 times, LED started to flash slowly for 10 seconds, during the flash, don’t press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success",
+		"inclusion": "Make sure connecting module to power supply and module has not joined Z-Wave network (if module joined any other Z-Wave network, please refer to the clauses 'Exclude device from a Z-Wave network'). \nFirst, set primary controller/gateway into inclusion mode. And press 'Button L' 3 times, LED starts to flash slowly for 10 seconds, during the flash, don't press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success. If module does not find a Z-Wave network within 10 seconds after join network function trigger, please try again. After joined Z-Wave network, please wait for a while until the app showing device is included. Then you can start enjoying with our module",
+		"exclusion": "Method 1: Factory Reset.\nMethod 2: First, set primary controller/gateway into exclusion mode. And press 'Button L' 3 times, LED started to flash slowly for 10 seconds, during the flash, don't press 'Button L' 3 times again, because it will cancel your last operation. Until LED is on for 3 seconds, means success",
 		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable. Hold Button L for 10 seconds, LED will flash slowly until flash fast for 2 seconds means success. After reset, module is exclude of Z-Wave network, please include again and learn motor again",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3461/actmotor001usermanual-E.pdf"
 	}

package/config/devices/0x0364/m5065.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "How to add a Z-Wave device\n\nYou can only add a maximum of six Z-Wave devices to the product at any given time. If the maximum number is reached, you need\nto remove a Z-Wave device before you can add a new one. See How to remove a Z-Wave device on page 39.\n\n1. Go to Setup > Wireless I/O.\n2. Select Enable Z-Wave and click Save. You may need to wait for a few minutes for Z-Wave to become active.\n3. Click Add. The product starts looking for Z-Wave devices in the Z-Wave network.\n4. Set the Z-Wave device to be added into learning (inclusion/exclusion) mode as described in its User Manual.\n5. If requested, enter the PIN delivered with the Z-Wave device, and click Enter.\n6. Wait until the adding process is finalized as indicated by Status: Done on the web page. The device’s status information\nwindow opens.\n7. Click Refresh to update the Z-Wave device info, e.g. battery status, and add a name for the device. Click Save",
+		"inclusion": "How to add a Z-Wave device\n\nYou can only add a maximum of six Z-Wave devices to the product at any given time. If the maximum number is reached, you need\nto remove a Z-Wave device before you can add a new one. See How to remove a Z-Wave device on page 39.\n\n1. Go to Setup > Wireless I/O.\n2. Select Enable Z-Wave and click Save. You may need to wait for a few minutes for Z-Wave to become active.\n3. Click Add. The product starts looking for Z-Wave devices in the Z-Wave network.\n4. Set the Z-Wave device to be added into learning (inclusion/exclusion) mode as described in its User Manual.\n5. If requested, enter the PIN delivered with the Z-Wave device, and click Enter.\n6. Wait until the adding process is finalized as indicated by Status: Done on the web page. The device's status information\nwindow opens.\n7. Click Refresh to update the Z-Wave device info, e.g. battery status, and add a name for the device. Click Save",
 		"exclusion": "How to remove a Z-Wave device\n\nNote\nThis is the recommended removal procedure.\n1. Go to Setup > Wireless I/O.\n2. Click Remove. The product starts looking for Z-Wave devices in the Z-Wave network.\n3. Set the Z-Wave device to be added into learning (inclusion/exclusion) mode as described in its User Manual.\n4. Wait until the removal process is finalized as indicated by Status: Done on the web page.\nThe Z-wave device is now removed from the Z-Wave Device List.\nNote\nAll product-related information in the removed Z-Wave device is erased",
 		"reset": "How to reset to factory default settings\n\nImportant\n\nReset to factory default should be used with caution. A reset to factory default resets all settings, including the IP address, to\nthe factory default values.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable\n\nTo reset the product to the factory default settings:\n1. Disconnect power from the product.\n2. Press and hold the control button and reconnect power.\n3. Keep the control button pressed for 15–30 seconds until the status LED indicator flashes amber.\n4. Release the control button. The process is complete when the status LED indicator turns green. The product has been reset\nto the factory default settings. If no DHCP server is available on the network, the default IP address is 192.168.0.90\n5. Using the installation and management software tools, assign an IP address, set the password, and access the video stream.\nThe installation and management software tools are available from the support pages at axis.com/support\nIt is also possible to reset parameters to factory default via the web interface. Go to Setup > System Options > Maintenance and\nclick Default",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3151/um_m5065_t10113315_en_1811.pdf"

package/config/devices/0x0366/pds-100.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Please proceed with the door lock open.\n1. Set the controller in inclusion mode.\n2. Open the battery cover of the indoor body and press the [R] button for 7 seconds.\n3. Press the [1][4][7] button after pressing the [R] button",
-		"exclusion": "Please proceed with the door lock open.\n1. Set the controller in exclusion mode.\n2. Open the battery cover of the indoor body and press the [R] button for 7 seconds.\n3. Press the [3][6][7] button after pressing the [R] button",
-		"reset": "Please proceed with the door lock open.\n1. Open the battery cover of the indoor body and press the [R] button for 9 seconds.\n2. Press the [1][2][3][6][5][4][7] button after pressing the [R] button.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor body and press the [R] button for 7 seconds.\n2. Press the [R] button, then press the [1], [4], and [7] buttons.",
+		"exclusion": "Ensure the door lock is open.\n1. Open the battery cover of the indoor body and press the [R] button for 7 seconds.\n2. Press the [R] button, then press the [3], [6], and [7] buttons.",
+		"reset": "Ensure the door lock is open.\n1. Open the battery cover of the indoor body and press the [R] button for 9 seconds.\n2. Press the [R] button, then press the [1], [2], [3], [6], [5], [4], and [7] buttons.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2974/Manual.pdf"
 	}
 }

package/config/devices/0x0370/zd2102-5.json

@@ -22,9 +22,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” (adding to) a network: Put the Z-Wave™ network controller into “inclusion” mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds",
-		"exclusion": "For “Exclusion” (removing from) a network: Put the Z-Wave™ network controller into “exclusion” mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the “Device Reset Locally Notification” command and reset to the factory default condition",
+		"inclusion": "For 'Inclusion' (adding to) a network: Put the Z-Wave™ network controller into 'inclusion' mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds",
+		"exclusion": "For 'Exclusion' (removing from) a network: Put the Z-Wave™ network controller into 'exclusion' mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
+		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the 'Device Reset Locally Notification' command and reset to the factory default condition",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2797/ZD%202102-5_R4_20170913%20(RED).pdf"
 	}
 }

package/config/devices/0x0370/zd2105us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2105 to your controller. To get in the “inclusion” mode, please press the Program Switch of ZD2105 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2105 will go to sleep after 20 seconds",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2105 from your controller. Press the Program Switch of ZD2105 for 1 second at least to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "*open the cover to send the Alarm Report and trigger the reed switch (close & open) 10 times in 10 seconds, ZD2105 will send the “Device Reset Locally Notification” command and reset to the factory default.\n * Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2105 to your controller. To get in the 'inclusion' mode, please press the Program Switch of ZD2105 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2105 will go to sleep after 20 seconds",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2105 from your controller. Press the Program Switch of ZD2105 for 1 second at least to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
+		"reset": "*open the cover to send the Alarm Report and trigger the reed switch (close & open) 10 times in 10 seconds, ZD2105 will send the 'Device Reset Locally Notification' command and reset to the factory default.\n * Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2805/ZD%202105-5_R1_20170913.pdf"
 	}
 }

package/config/devices/0x0370/zd2112jp-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2112 to your controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2112 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2112 will go to sleep after 20 seconds.",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2112 from your controller. Press the program switch of ZD2112 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2112 will send the “Device Reset Locally Notification” command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2112 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2112 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2112 will go to sleep after 20 seconds.",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2112 from your controller. Press the program switch of ZD2112 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2112 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2796/ZD%202112-5_R1_20170913.pdf"
 	}
 }

package/config/devices/0x0371/zw187.json

@@ -147,7 +147,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Press the sensor latch with a slotting screwdriver to remove the lid of the sensor.\n2. Squeeze the sides of the sensor casing to alleviate pressure on the chipboard; slide the chipboard out.\n3. Remove the Pull Tab to engage the pre-installed battery. The sensor’s LED will fade the color red in and out for a few seconds to indicate that it’s powered on.\n4. Set your gateway into its 'add device' mode. Refer to its manual if you are unsure of how to perform this step. Then press Recessed Door Sensor 7's Action Button once; its LED will blink.\nIf your gateway supports S2 security, and you want your device to use this higher level of security, please enter the first 5 digits of the DSK into the gateway's interface when prompted. Refer to the gateway's manual if you are unsure how to perform this step. Do not lose the DSK or remove it from the product or package.\n5. When Recessed Door Sensor 7 successfully joins your Z-Wave network its LED will turn solid red for 10 minutes and then off. If fails, its LED turns slow fade-in fade-out red color. Repeat the above steps and please contact us for further support if needed.\n6. Squeeze the sides of the sensor casing lightly again and re-insert the chipboard as it was. Re-attach the lid",
+		"inclusion": "1. Press the sensor latch with a slotting screwdriver to remove the lid of the sensor.\n2. Squeeze the sides of the sensor casing to alleviate pressure on the chipboard; slide the chipboard out.\n3. Remove the Pull Tab to engage the pre-installed battery. The sensor's LED will fade the color red in and out for a few seconds to indicate that it's powered on.\n4. Set your gateway into its 'add device' mode. Refer to its manual if you are unsure of how to perform this step. Then press Recessed Door Sensor 7's Action Button once; its LED will blink.\nIf your gateway supports S2 security, and you want your device to use this higher level of security, please enter the first 5 digits of the DSK into the gateway's interface when prompted. Refer to the gateway's manual if you are unsure how to perform this step. Do not lose the DSK or remove it from the product or package.\n5. When Recessed Door Sensor 7 successfully joins your Z-Wave network its LED will turn solid red for 10 minutes and then off. If fails, its LED turns slow fade-in fade-out red color. Repeat the above steps and please contact us for further support if needed.\n6. Squeeze the sides of the sensor casing lightly again and re-insert the chipboard as it was. Re-attach the lid",
 		"exclusion": "1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.\n2. Make sure the product is powered. \n3. Single-click Action Button; LED will become flash red color for 5 seconds, which indicates entering exclusion mode. \n4. If the exclusion is successful, LED will change to the default unpaired state which is slow fade-in fade-out red color. \n5. Should its LED extinguish without slow fade-in fade-out red color, it indicates the exclusion is unsuccessful. Contact us for further support if needed",
 		"reset": "If the primary controller is missing or inoperable, you may need to reset the device to factory settings.\nMake sure the product is powered. To complete the reset process manually, press and hold the Action Button for at least 20s, and Factory Reset is performed when released. The LED will become slow fade-in fade-out red color, which indicates the reset operation is successful. Contact us for further support if needed. \nNote: \n1. This procedure should only be used when the primary controller is missing or inoperable.\n2. Factory Reset will:\n(a) Remove the product from Z-Wave network;\n(b) Delete the Association setting;\n(c) Restore the configuration settings to the default.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3620/Recessed%20Door%20Sensor%207%20-%20Product%20Manual.pdf"

package/config/devices/0x0371/zwa005.json

@@ -245,8 +245,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Press once TriSensor’s Action Button. If it is the first installation, the yellow LED will keep solid until whole network processing is complete. If successful, the LED will flash white -> green -> white -> green, after 2 seconds finished. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once.\nIf it is the S2 encryption network, please enter the first 5 digits of DSK.",
-		"exclusion": "Press once TriSensor’s Action Button, the Purple LED will keep solid until whole network processing is complete. If the exclusion is successful, the LED will flash white -> green ->white -> green and then LED will pulse a blue. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once",
+		"inclusion": "Press once TriSensor's Action Button. If it is the first installation, the yellow LED will keep solid until whole network processing is complete. If successful, the LED will flash white -> green -> white -> green, after 2 seconds finished. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once.\nIf it is the S2 encryption network, please enter the first 5 digits of DSK.",
+		"exclusion": "Press once TriSensor's Action Button, the Purple LED will keep solid until whole network processing is complete. If the exclusion is successful, the LED will flash white -> green ->white -> green and then LED will pulse a blue. If failed, the yellow LED lasts for 30 seconds, then the green LED flashes once",
 		"reset": "1. Power up the device. \n2. Press and hold the button for 15s until Red LED is blinking,then release the button\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2898/TriSensor%20user%20manual%2020180416.pdf"
 	}

package/config/devices/0x0371/zwa006.json

@@ -113,8 +113,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Power on the device, and the power led will blink blue slowly.\n2. Put the Z-Wave Primary Controller into inclusion mode (If you don’t know how to do this, refer to its manual)\n3. Press and hold the action button, and when the yellow LED is on, release the button. It indicates the device has enter learn mode.\n4. If added successfully, the power LED will remain green for 2 seconds, then turn off",
-		"exclusion": "1. Power on the device.\n2. Put the Primary Controller into exclusion mode (If you don’t know how to do this refer to its manual)\n3. Press and hold the action button, and when the purple LED turns on, release the button. This indicates that the device has entered learn mode. If removal is successful, the blue LED will blink slowly",
+		"inclusion": "1. Power on the device, and the power led will blink blue slowly.\n2. Put the Z-Wave Primary Controller into inclusion mode (If you don't know how to do this, refer to its manual)\n3. Press and hold the action button, and when the yellow LED is on, release the button. It indicates the device has enter learn mode.\n4. If added successfully, the power LED will remain green for 2 seconds, then turn off",
+		"exclusion": "1. Power on the device.\n2. Put the Primary Controller into exclusion mode (If you don't know how to do this refer to its manual)\n3. Press and hold the action button, and when the purple LED turns on, release the button. This indicates that the device has entered learn mode. If removal is successful, the blue LED will blink slowly",
 		"reset": "Please use this procedure only when the primary controller is missing or inoperable.\n\n1. Make sure the device has been powered.\n2. Press and hold the action button for 15 seconds. When the red LED turns on, release the button. Then, the device will enter factory reset mode. If the reset is successful, the LED will blink blue slowly.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3067/Smart%20Boost%20Timer%20Switch%20User%20Manual-V1.9.pdf"
 	}

package/config/devices/0x0371/zwa046_1phase_eu.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "1. Turn your gateway/ main controller into adding mode.\n2. Press once the Action Button on the product",
 		"exclusion": "1. Turn your gateway/ main controller into removing mode.\n2. Press once the Action Button on the product",
-		"reset": "Press and hold the Action Button on product for 10s.\n\nNote: Please use this procedure only when the network’s primary controller is missing or otherwise inoperable."
+		"reset": "Press and hold the Action Button on product for 10s.\n\nNote: Please use this procedure only when the network's primary controller is missing or otherwise inoperable."
 	},
 	"associations": {
 		"1": {

package/config/devices/0x0371/zwa046_2phase_us.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "1. Turn your gateway/ main controller into adding mode.\n2. Press once the Action Button on the product",
 		"exclusion": "1. Turn your gateway/ main controller into removing mode.\n2. Press once the Action Button on the product",
-		"reset": "Press and hold the Action Button on product for 10s.\n\nNote: Please use this procedure only when the network’s primary controller is missing or otherwise inoperable."
+		"reset": "Press and hold the Action Button on product for 10s.\n\nNote: Please use this procedure only when the network's primary controller is missing or otherwise inoperable."
 	},
 	"associations": {
 		"1": {