@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x0090/ged1455.json

@@ -221,8 +221,8 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button “A” on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
+		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
 		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
 		"manual": "http://www.weiserlock.com/PDFs/instructions/Electronics/SmartCode_5_Installation_and_User_Guide_English.pdf"
 	}

package/config/devices/0x0090/ged2350.json

@@ -172,8 +172,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button “A” on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
+		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
 		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2377/Install%20Guide%20GED2350%2004242017.pdf"
 	}

package/config/devices/0x0090/smartcode_888.json

@@ -184,8 +184,8 @@
 		]
 	},
 	"metadata": {
-		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button “A” on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
-		"exclusion": "Follow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
+		"inclusion": "Initiate the process to add the lock to your system at your smart home controller.\nWhen prompted by your smart home system to add the lock, press button 'A' on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.\nPlease allow time for the controller to add the lock to your system",
+		"exclusion": "Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A' on the lock interior once. The red LED will illuminate when the lock enters Remove mode.",
 		"reset": "A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.\nPlease only perform a factory reset when the primary controller is missing or inoperable.\n\nTo perform a factory reset, please perform the following: \n1. Remove the battery pack\n2. Press and HOLD the Program button while reinserting the battery pack.\n3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.\n4. Press the Program button once more. The status LED will flash green and red several times.\n5. After a few seconds, the lock will initiate the door handing process",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2176/Install%20Guide%20888%20ENG_Merged.pdf"
 	}

package/config/devices/0x0094/2gig-edg-n.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Reset Controller\nAvailable only for Installers, the Reset Controller option\nis also found on the Z-Wave settings menu.\nReset the panel’s Z-Wave Controller back to default\nsettings.\n1. Tap Reset Controller",
+		"reset": "Reset Controller\nAvailable only for Installers, the Reset Controller option\nis also found on the Z-Wave settings menu.\nReset the panel's Z-Wave Controller back to default\nsettings.\n1. Tap Reset Controller",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4076/10029908%20Rev-X11b%20-%202GIG%20Edge%20User%20Guide_sm.pdf"
 	}
 }

package/config/devices/0x0094/adc-200h-ev.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1.1 Adding devices to the Alarm.com Module’s Z-Wave Network\nNOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com Module will have network information replicated over to them.\n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest.\nb. Move all Z-Wave devices to their final location on the property.\nc. Navigate to the Equipment List page.\nd. Select emPower Management.\ne. Select Add Z-Wave Devices\nf. Wait for the bolded message: Checking for new devices on the network\ng. Trigger a device to add it to the network.\nh. When a device is added successfully, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page.\nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List.\nd. Click Add Z-Wave Devices.\ne. Wait for the bolded message: Checking for new devices on the network.\nf. Trigger a device to add it to the network.\ng. When a device is added successfully, it will show up on this screen following a 30 second delay.\nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n3. Using the Simon XTi Panel\na. Enter System Programming.\nb. Select Interactive Services.\nc. Select Z-Wave.\nd. Select Add Device.\ne. Trigger a device to add it to the network.\nf. When a device is added successfully, the panel will beep.\ng. You will need to re-enter Add Mode before triggering the next device",
+		"inclusion": "1.1 Adding devices to the Alarm.com Module's Z-Wave Network\nNOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com Module will have network information replicated over to them.\n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest.\nb. Move all Z-Wave devices to their final location on the property.\nc. Navigate to the Equipment List page.\nd. Select emPower Management.\ne. Select Add Z-Wave Devices\nf. Wait for the bolded message: Checking for new devices on the network\ng. Trigger a device to add it to the network.\nh. When a device is added successfully, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page.\nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List.\nd. Click Add Z-Wave Devices.\ne. Wait for the bolded message: Checking for new devices on the network.\nf. Trigger a device to add it to the network.\ng. When a device is added successfully, it will show up on this screen following a 30 second delay.\nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n3. Using the Simon XTi Panel\na. Enter System Programming.\nb. Select Interactive Services.\nc. Select Z-Wave.\nd. Select Add Device.\ne. Trigger a device to add it to the network.\nf. When a device is added successfully, the panel will beep.\ng. You will need to re-enter Add Mode before triggering the next device",
 		"exclusion": "List page.\nd. Select emPower Management.\ne. Select Delete Z-Wave Devices\nf. Wait for the bolded message: Checking for deleted devices on the network\ng. Trigger a device to remove it from the network.\nh. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to delete close to the Alarm.com Module.\nb. Navigate to the Equipment page.\nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List.\ne. Click Delete Z-Wave Devices.\nf. Wait for the bolded message: Checking for deleted devices on the network.\ng. Trigger a device to remove it from the network.\nh. When a device is deleted successfully and its network information is erased, it will show up on this screen following a 30 second delay.\ni. Continue triggering devices. You may delete many devices to the network without reentering Delete Mode.\n3. Using the Simon XTi Panel\na. Enter System Programming.\nb. Select Interactive Services.\nc. Select Z-Wave.\nd. Select Delete Device.\ne. Trigger a device to remove it from the network.\nf. When a device is deleted successfully and its network information is erased, the panel will beep.\ng. You will need to re-enter Delete Mode before triggering the next device",
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\n1.3 Reset Alarm.com Module to default state\nNOTE: This function will forcibly clear the Alarm.com module’s Z-Wave node identification and will also remove all network information from the module.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page.\n3. Click the “emPower Devices” tab.\n4. Open the “Advanced Z-Wave Commands” menu by clicking the button below the Equipment List.\n5. Towards the bottom next to the “Equipment List Label” text click on the “Reset To Factory Default” button\n6. Allow 3 minutes for the associated commands to go through and for the module to act on them",
+		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\n1.3 Reset Alarm.com Module to default state\nNOTE: This function will forcibly clear the Alarm.com module's Z-Wave node identification and will also remove all network information from the module.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page.\n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List.\n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the module to act on them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1686/SimonXT_XTi_VoLTEModule_InstallGuide_EN_ZWVP.pdf"
 	}
 }

package/config/devices/0x0094/adc-470l.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "NOTE: This function will forcibly clear the Alarm.com ADC-470L’s Z-Wave node identification and will also remove all network information from the ADC-470L. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the “emPower Devices” tab.\n4. Open the “Advanced Z-Wave Commands” menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the “Equipment List Label” text click on the “Reset To Factory Default” button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-470L to act on them",
+		"reset": "NOTE: This function will forcibly clear the Alarm.com ADC-470L's Z-Wave node identification and will also remove all network information from the ADC-470L. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-470L to act on them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2297/Alarm.com%20ADC-470L%20Z-Wave%20Documentation%20v1.docx"
 	}
 }

package/config/devices/0x0094/adc-620t.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-620T’s Z-Wave node identification and will also remove all network information from the ADC-620T. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the “emPower Devices” tab.\n4. Open the “Advanced Z-Wave Commands” menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the “Equipment List Label” text click on the “Reset To Factory Default” button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-620T to act on them",
+		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-620T's Z-Wave node identification and will also remove all network information from the ADC-620T. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-620T to act on them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3176/Alarm.com%20ADC-620T%20Z-Wave%20Documentation%2012_11_18v2.pdf"
 	}
 }

package/config/devices/0x0094/adc-nk-100t.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nThis resets the Hub to its factory settings.\nCAUTION: Factory Resetting erases all\ndevices and settings.\nNOTE: The command to enable or disable\nFactory Resetting can be sent from the\nAlarm.com Dealer Website’s AirFX Toolkit.\nFactory Resetting is only available during\nthe first 120 seconds after initially powering\non the Hub.\n• After entering Advanced Mode, press and hold the\nEnrollment button ( ) for 10 seconds. When the\nreset process has begun, the Status Light will blink\norange slowly and the Hub will beep five times.\n• To cancel Factory Resetting, you must\nimmediately press and release the Enrollment\nbutton ( ). This feature is only available\nduring the first five seconds after Factory\nResetting has begun.\n• When Factory Resetting is complete, the Status\nLight will shine solid orange for 10 seconds.\n• Next, contact Alarm.com Customer Support to\nreinitialize the Hub",
+		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nThis resets the Hub to its factory settings.\nCAUTION: Factory Resetting erases all\ndevices and settings.\nNOTE: The command to enable or disable\nFactory Resetting can be sent from the\nAlarm.com Dealer Website's AirFX Toolkit.\nFactory Resetting is only available during\nthe first 120 seconds after initially powering\non the Hub.\n• After entering Advanced Mode, press and hold the\nEnrollment button ( ) for 10 seconds. When the\nreset process has begun, the Status Light will blink\norange slowly and the Hub will beep five times.\n• To cancel Factory Resetting, you must\nimmediately press and release the Enrollment\nbutton ( ). This feature is only available\nduring the first five seconds after Factory\nResetting has begun.\n• When Factory Resetting is complete, the Status\nLight will shine solid orange for 10 seconds.\n• Next, contact Alarm.com Customer Support to\nreinitialize the Hub",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1760/ADC_BB_hub_user_manual_060316.pdf"
 	}
 }

package/config/devices/0x0094/adc-sg130z.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "This process will clear all nodes from the Alarm.com Z-Wave device’s network, change the Alarm.com Z-Wave device’s home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps:\n\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the “Equipment” page.\n3. Click the “Z-Wave Devices” tab.\n4. Under the “Advanced Z-Wave Commands” header, click “Remove All Z-Wave Devices.”\n5. Allow 3 minutes for the associated commands to go through and for the Alarm.com Z-Wave\ndevice to act on them.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only if the network primary controller is missing or otherwise inoperable",
+		"reset": "This process will clear all nodes from the Alarm.com Z-Wave device's network, change the Alarm.com Z-Wave device's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps:\n\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'Z-Wave Devices' tab.\n4. Under the 'Advanced Z-Wave Commands' header, click 'Remove All Z-Wave Devices.'\n5. Allow 3 minutes for the associated commands to go through and for the Alarm.com Z-Wave\ndevice to act on them.\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only if the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4151/Alarm.com-SupplementalZ-WaveDocumentationv6_9_2.pdf"
 	}
 }

package/config/devices/0x0094/adtzwm_for_comman.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-SG-100Z’s Z-Wave node identification and will also remove all network information from the ADC-SG-100Z. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the “emPower Devices” tab.\n4. Open the “Advanced Z-Wave Commands” menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the “Equipment List Label” text click on the “Reset To Factory Default” button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-SG-100Z to act on them",
+		"reset": "Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.\n\nNOTE: This function will forcibly clear the Alarm.com ADC-SG-100Z's Z-Wave node identification and will also remove all network information from the ADC-SG-100Z. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n1. A Z-Wave factory reset must be triggered from the Alarm.com dealer site\n2. Navigate to the Equipment page. \n3. Click the 'emPower Devices' tab.\n4. Open the 'Advanced Z-Wave Commands' menu by clicking the button below the Equipment List. \n5. Towards the bottom next to the 'Equipment List Label' text click on the 'Reset To Factory Default' button\n6. Allow 3 minutes for the associated commands to go through and for the ADC-SG-100Z to act on them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3214/Alarm.com%20ADC-SG-100Z%20Z-Wave%20Documentation%2001_24_19.pdf"
 	}
 }

package/config/devices/0x0094/ht-138s.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "NOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com GATEWAY will have network information replicated over to them. \n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices to their final location on the property. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Add Z-Wave Devices \nf. Wait for the bolded message: Checking for new devices on the network \ng. Trigger a device to add it to the network. \nh. When a device is added successfully, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page. \nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List. \nd. Click Add Z-Wave Devices. \ne. Wait for the bolded message: Checking for new devices on the network. \nf. Trigger a device to add it to the network. \ng. When a device is added successfully, it will show up on this screen following a 30 second delay. \nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.",
 		"exclusion": "1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Remove Z-Wave Devices \nf. Wait for the bolded message: Checking for removed devices on the network \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY.\nb. Navigate to the Equipment page. \nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List. \ne. Click Remove Z-Wave Devices. \nf. Wait for the bolded message: Checking for removed devices on the network. \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.",
-		"reset": "2.4 Reset Alarm.com Z-WAVE DEVICE to default state\n\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE’s network, change the Alarm.com Z-WAVE DEVICE’s home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps: 1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n\n2. Navigate to the “Equipment” page.\n\n3. Click the “emPower Devices” tab.\n\n4. Expand the “Advanced Z-Wave Commands” box.\n\n5. Click the “Remove All Z-Wave Devices” button.\n\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act on them",
+		"reset": "2.4 Reset Alarm.com Z-WAVE DEVICE to default state\n\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE's network, change the Alarm.com Z-WAVE DEVICE's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset, follow these steps: 1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n\n2. Navigate to the 'Equipment' page.\n\n3. Click the 'emPower Devices' tab.\n\n4. Expand the 'Advanced Z-Wave Commands' box.\n\n5. Click the 'Remove All Z-Wave Devices' button.\n\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act on them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3298/Alarm.com%20Gateway-Supplemental%20Z-WaveDocumentation%20V5%20-%20Bezeq.pdf"
 	}
 }

package/config/devices/0x0094/ws900-29.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "NOTE: This process leverages Network Wide Inclusion. In addition, any controllers added to the Alarm.com GATEWAY will have network information replicated over to them. \n1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices to their final location on the property. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Add Z-Wave Devices \nf. Wait for the bolded message: Checking for new devices on the network \ng. Trigger a device to add it to the network. \nh. When a device is added successfully, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may add many devices to the network without reentering Add Mode.\n2. Using the Dealer Website\na. Navigate to the Equipment page. \nb. Click the emPower Devices tab.\nc. Open the Advanced Z-Wave Commands menu below the Equipment List. \nd. Click Add Z-Wave Devices. \ne. Wait for the bolded message: Checking for new devices on the network. \nf. Trigger a device to add it to the network. \ng. When a device is added successfully, it will show up on this screen following a 30 second delay. \nh. Continue triggering devices. You may add many devices to the network without reentering Add Mode.",
 		"exclusion": "1. Using Mobiletech\na. Install the MobileTech App (if not already done) and select the customer of interest. \nb. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY. \nc. Navigate to the Equipment List page. \nd. Select emPower Management. \ne. Select Remove Z-Wave Devices \nf. Wait for the bolded message: Checking for removed devices on the network \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.\n2. Using the Dealer Website\na. Move all Z-Wave devices you plan to remove close to the Alarm.com GATEWAY.\nb. Navigate to the Equipment page. \nc. Click the emPower Devices tab.\nd. Open the Advanced Z-Wave Commands menu below the Equipment List. \ne. Click Remove Z-Wave Devices. \nf. Wait for the bolded message: Checking for removed devices on the network. \ng. Trigger a device to remove it from the network. \nh. When a device is removed successfully and its network information is erased, it will show up on this screen following a 30 second delay. \ni. Continue triggering devices. You may remove many devices to the network without reentering Remove Mode.",
-		"reset": "2.6 Reset Alarm.com Z-WAVE DEVICE to default state\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE’s network, change the Alarm.com ZWAVE DEVICE’s home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset,\nfollow these steps:\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the “Equipment” page.\n3. Click the “emPower Devices” tab.\n4. Expand the “Advanced Z-Wave Commands” box.\n5. Click the “Remove All Z-Wave Devices” button.\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act\non them",
+		"reset": "2.6 Reset Alarm.com Z-WAVE DEVICE to default state\nThis process will clear all nodes from the Alarm.com Z-WAVE DEVICE's network, change the Alarm.com ZWAVE DEVICE's home ID, and reset all Z-Wave settings to their default values. To perform a Z-Wave reset,\nfollow these steps:\n1. Log into the Partner Portal at https://alarmadmin.alarm.com/default.aspx and select a customer.\n2. Navigate to the 'Equipment' page.\n3. Click the 'emPower Devices' tab.\n4. Expand the 'Advanced Z-Wave Commands' box.\n5. Click the 'Remove All Z-Wave Devices' button.\n6. Allow 3 minutes for the associated commands to go through and for the Z-WAVE DEVICE to act\non them",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3784/Alarm.com-SupplementalZ-WaveDocumentationv6.1_new.pdf"
 	}
 }

package/config/devices/0x009b/2gig-gc3-345.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "From the GC3 Home Screen enter System Settings using the Master Code. Tap on Smart Home Settings and then tap on the Advanced Settings tile. Tap on the Reset Controller tile. The system will present a confirmation. Tap the confirmation. The system will reset the GC3 Z-Wave network. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. From the GC3 Home Screen enter System Settings using the Master Code.\n2. Tap on Smart Home Settings and then tap on the Advanced Settings tile.\n3. Tap on the Reset Controller tile.\n4. The system will present a confirmation. Tap the confirmation.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1605/GC3%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x009b/2gig-stz.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Set your primary controller to Include, add or Install mode, to add the thermostat as a node on\n\nyour network (see your controller’s user manual for detailed instructions).\n\n2. Touch any button to take the thermostat out of sleep mode.\n\n3. Touch and hold MODE button for 5 seconds. SETUP will be displayed in the status display line.\n\n4. Scroll to “Z-Wave” using  buttons. Touch FAN (Select).\n\n5. When prompted by your Z-Wave controller, select YES in the Z-Wave Install screen.\n\n6. Touch FAN (Select) to add thermostat to network.\n\n7. The display line should flash WAIT and then SUCCESS if Z-Wave connection is made.\n\n8. If Z-Wave does not connect to controller, WAIT, then FAIL will flash in status display line.\n\n9. If thermostat fails to connect, repeat Steps three (3) through (7) to re-try connecting.\n\nYour controller will indicate the thermostat was successfully added to its network (see your controller’s user manual for details). Also, you can check if the thermostat was successfully added to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the thermostat INFO screen.",
-		"exclusion": "Removing from a Z-Wave Network\nTo remove the thermostat from the network, use the following steps.\n1. Set your primary controller to exclude or remove mode to remove the thermostat as a node on\nyour network (see your controller’s user manual for detailed instructions).\n2. Touch any button to take the thermostat out of sleep mode.\n3. Touch and hold the MODE button for 5 seconds. SETUP will be displayed in the status display line.\n5. Scroll to “Z-Wave” using  buttons. Touch FAN (Select).\n6. When prompted by your Z-Wave controller, select YES in the Z-Wave exclude screen.\n7. Touch FAN (Select) to remove thermostat to network.\n8. The display line should flash WAIT then SUCCESS if the thermostat is removed from the network.\n9. If the removal operation is not successful, WAIT will flash, then FAIL will flash in status display\nline. Repeat Steps three (3) through (7) to re-try",
+		"inclusion": "1. Set your primary controller to Include, add or Install mode, to add the thermostat as a node on\n\nyour network (see your controller's user manual for detailed instructions).\n\n2. Touch any button to take the thermostat out of sleep mode.\n\n3. Touch and hold MODE button for 5 seconds. SETUP will be displayed in the status display line.\n\n4. Scroll to 'Z-Wave' using  buttons. Touch FAN (Select).\n\n5. When prompted by your Z-Wave controller, select YES in the Z-Wave Install screen.\n\n6. Touch FAN (Select) to add thermostat to network.\n\n7. The display line should flash WAIT and then SUCCESS if Z-Wave connection is made.\n\n8. If Z-Wave does not connect to controller, WAIT, then FAIL will flash in status display line.\n\n9. If thermostat fails to connect, repeat Steps three (3) through (7) to re-try connecting.\n\nYour controller will indicate the thermostat was successfully added to its network (see your controller's user manual for details). Also, you can check if the thermostat was successfully added to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the thermostat INFO screen.",
+		"exclusion": "Removing from a Z-Wave Network\nTo remove the thermostat from the network, use the following steps.\n1. Set your primary controller to exclude or remove mode to remove the thermostat as a node on\nyour network (see your controller's user manual for detailed instructions).\n2. Touch any button to take the thermostat out of sleep mode.\n3. Touch and hold the MODE button for 5 seconds. SETUP will be displayed in the status display line.\n5. Scroll to 'Z-Wave' using  buttons. Touch FAN (Select).\n6. When prompted by your Z-Wave controller, select YES in the Z-Wave exclude screen.\n7. Touch FAN (Select) to remove thermostat to network.\n8. The display line should flash WAIT then SUCCESS if the thermostat is removed from the network.\n9. If the removal operation is not successful, WAIT will flash, then FAIL will flash in status display\nline. Repeat Steps three (3) through (7) to re-try",
 		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the 2GIG-STZ-1's Z-Wave parameters to Factory Settings (both Z-Wave and HVAC settings):\n1. Touch and hold MODE button to go to Setup menu.\n2. Touch and hold MODE and the down arrow key to enter Advanced Menu.\n3. Navigate to Restore Defaults to perform a factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3884/10028238%20Rev-E%20-%202GIG-STZ-1%20User%20Guide_PRINT.pdf"
 	}

package/config/devices/0x0106/piper_nv.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Z-Wave Network Reset\nThe Z-Wave network reset procedure performs a default factory reset on Piper’s Z-Wave controller component, which clears all user and Z- Wave network settings. A new Z-Wave network will be established. Afterwards, any previously existing Z-Wave devices must be reset and then added to the new network via the Piper app.\nThe Reset Z-Wave option is located under Settings->Wireless Accessories->Advanced Options\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Z-Wave Network Reset\nThe Z-Wave network reset procedure performs a default factory reset on Piper's Z-Wave controller component, which clears all user and Z- Wave network settings. A new Z-Wave network will be established. Afterwards, any previously existing Z-Wave devices must be reset and then added to the new network via the Piper app.\nThe Reset Z-Wave option is located under Settings->Wireless Accessories->Advanced Options\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1629/PIP-UserManualContent-291116-0905-386.pdf"
 	}
 }

package/config/devices/0x0108/dch-g020.json

@@ -16,7 +16,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press and hold the “Reset button” for 5 seconds on DCH‐G020",
+		"reset": "Press and hold the 'Reset button' for 5 seconds on DCH‐G020",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1297/DLink_DCH-G020_manual_v1.1.pdf"
 	}
 }

package/config/devices/0x0108/dch-g021.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "On home tile screen click “Hub Settings”\nClick “Advanced Options”\nClick “Restore” (under Restore to Factory Settings) and follow the on screen instructions.",
+		"reset": "On home tile screen click 'Hub Settings'\nClick 'Advanced Options'\nClick 'Restore' (under Restore to Factory Settings) and follow the on screen instructions.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1145/Connect_insert_FINAL_Outline.pdf"
 	}
 }

package/config/devices/0x0108/dch-g022.json

@@ -23,7 +23,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "Press and hold the “Reset button” for 5 seconds on DCH-G022\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Press and hold the 'Reset button' for 5 seconds on DCH-G022\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2052/DLink_DCH-G022_manual%20v2.pdf"
 	}
 }

package/config/devices/0x0109/azl7434.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZL 7434-5 to your controller. To get in the “inclusion” mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included",
-		"exclusion": "Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZL 7434-5 from your controller. \nPress 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
-		"reset": "Power off first, press Program Switch and power on, ZL7434-5 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL 7434-5 to your controller. To get in the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included",
+		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL 7434-5 from your controller. \nPress 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
+		"reset": "Power off first, press Program Switch and power on, ZL7434-5 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1378/Microsoft%20Word%20-%20ZL7434-5%20In-Wall%20Switch%20-%201%20Relay_20150520.pdf"
 	}
 }

package/config/devices/0x0109/za1011eu-5.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "1) Select “Reset Locally” button.\n2) Confirm the dialog. This will perform a factory reset to the Gateway.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1) Select 'Reset Locally' button.\n2) Confirm the dialog. This will perform a factory reset to the Gateway.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3417/ZA1011EU-5_UserManual.pdf"
 	}
 }

package/config/devices/0x0109/zb5311us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZB5311-5 to your controller. To get in the “inclusion” mode, press the Program Switch of ZB5311-5 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZB5311-5 will go to sleep after 30 seconds. After inclusion successfully, the Green LED will be solid on for 0.5 second",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZB5311-5 from your controller. Press the Program Switch of ZB5311-5 once to be excluded, the Green LED will flash 5 times quickly after successful exclusion.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: Long press the program switch up to 10 seconds to send the “Device Reset Locally Notification” command and reset to the factory default. The Green LED will flash 5 times quickly after finishing the Factory Default Reset.\n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZB5311-5 to your controller. To get in the 'inclusion' mode, press the Program Switch of ZB5311-5 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZB5311-5 will go to sleep after 30 seconds. After inclusion successfully, the Green LED will be solid on for 0.5 second",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZB5311-5 from your controller. Press the Program Switch of ZB5311-5 once to be excluded, the Green LED will flash 5 times quickly after successful exclusion.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"reset": "Factory Default Reset: Long press the program switch up to 10 seconds to send the 'Device Reset Locally Notification' command and reset to the factory default. The Green LED will flash 5 times quickly after finishing the Factory Default Reset.\n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3819/ZB5311-5%20Glass%20Break%20Detector%20Manual%20(RD%20%20FCC%20Checked)_20200304.pdf"
 	}
 }

package/config/devices/0x0109/zd2105.json

@@ -20,9 +20,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2105 to your controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2105 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2105 will go to sleep after 20 seconds",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2105 from your controller. Press the Program Switch of ZD2105 for 1 second at least to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2105 will send the “Device Reset Locally Notification” command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2105 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2105 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2105 will go to sleep after 20 seconds",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2105 from your controller. Press the Program Switch of ZD2105 for 1 second at least to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
+		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2105 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n\n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2850/ZD%202105-5_20180126%20(SDK6.81).pdf"
 	}
 }

package/config/devices/0x0109/zd2106us-7.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2106 to your controller. To get in the “inclusion” mode, make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2106 will go to sleep after 30 seconds",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2106 from your controller. Make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: \nOpen the rear cover to trigger the rear cover switch for sending the Alarm Report and trigger the reed switch (close & open) 10 times in 10 seconds, ZD2106 will send the “Device Reset Locally Notification” command and reset to the factory default. \n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2106 to your controller. To get in the 'inclusion' mode, make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2106 will go to sleep after 30 seconds",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2106 from your controller. Make sure the rear cover has been closed firmly and trigger the reed switch (close & open) 3 times within 5 seconds for sending the NIF to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"reset": "Factory Default Reset: \nOpen the rear cover to trigger the rear cover switch for sending the Alarm Report and trigger the reed switch (close & open) 10 times in 10 seconds, ZD2106 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n(Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3878/ZD2106-7%20Door%20Sensor%20(20200506).pdf"
 	}
 }

package/config/devices/0x0109/zd2112jp-5.json

@@ -36,9 +36,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2112 to your controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2112 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2112 will go to sleep after 20 seconds.",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2112 from your controller. Press the program switch of ZD2112 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2112 will send the “Device Reset Locally Notification” command and reset to the factory default. \n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2112 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2112 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2112 will go to sleep after 20 seconds.",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2112 from your controller. Press the program switch of ZD2112 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2112 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1750/ZD%202112-5_12122014-Japan%20DW.pdf"
 	}
 }

package/config/devices/0x0109/zd2201.json

@@ -69,9 +69,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2301 to your controller, to get in the “inclusion” mode. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
-		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the “Device Reset Locally” command and reset to the factory default. \n* Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2301 to your controller, to get in the 'inclusion' mode. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
+		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the 'Device Reset Locally' command and reset to the factory default. \n* Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2480/ZD%202201-5_R1_20150812.pdf"
 	}
 }

package/config/devices/0x0109/zd2301eu-5.json

@@ -68,9 +68,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "4. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZD2301 to your controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "5. For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
-		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the “Device Reset Locally” command and reset to the factory default. \n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "4. For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZD2301 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
+		"exclusion": "5. For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded.\nNote: All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"reset": "Factory Default Reset: \n*Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the 'Device Reset Locally' command and reset to the factory default. \n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1334/ZD%202301-5_20150603.pdf"
 	}
 }

package/config/devices/0x0109/zf5201eu-5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZF5201 to the controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZF5201 to the controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
 		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1718/ZF%205201-5_20141118.pdf"
 	}

package/config/devices/0x0109/zl7201de-5.json

@@ -22,8 +22,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZL7201 into your controller. To get in the “Inclusion” mode, the distance between ZL7201 and controller is suggested to be in one meter. By power up to get included for first time, or press the Program switch (The LED at the top of plug-in) 3 times within 2 seconds to be included",
-		"exclusion": "For “Exclusion” from (removing from) a network: Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZL7201 from your controller. Press the Program Switch (The LED at the top of plug-in) 3 times within 2 seconds to be excluded",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL7201 into your controller. To get in the 'Inclusion' mode, the distance between ZL7201 and controller is suggested to be in one meter. By power up to get included for first time, or press the Program switch (The LED at the top of plug-in) 3 times within 2 seconds to be included",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL7201 from your controller. Press the Program Switch (The LED at the top of plug-in) 3 times within 2 seconds to be excluded",
 		"reset": "Reset: Press the Program Switch (The LED at the top of plug-in) then power on (plug-in) and hold for 5 seconds before release the switch.\n\nNoticed: only use Reset for the situation where the primary controller is inoperable or lost",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1083/ZL%207261-5_%20Power%20Monitor_20140814.pdf"
 	}

package/config/devices/0x0109/zl7435-5.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZL 7435EU-5 to your controller. To get in the “inclusion” mode, the distance between module and controller is suggested to be in one meter. \nPress 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included.",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZL 7435EU-5 from your controller. Press 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
-		"reset": "Factory Default Reset: Power off first, press Program Switch and power on till 10 seconds, ZL7435EU-5 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZL 7435EU-5 to your controller. To get in the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. \nPress 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included.",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZL 7435EU-5 from your controller. Press 3 times within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be excluded.",
+		"reset": "Factory Default Reset: Power off first, press Program Switch and power on till 10 seconds, ZL7435EU-5 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1367/ZL7435-5%20In-Wall%20Switch%20-%202%20Relays_20141205.pdf"
 	}
 }

package/config/devices/0x0109/zm1601-5.json

@@ -47,8 +47,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” (adding to) a network, put the Z-Wave™ network controller into “inclusion” mode, and following its instruction to add the ZM 1601 to your controller. To get the ZM 1601 in the “inclusion” mode, open the bracket and press the program switch of ZM 1601 for 1 second at least & release to be included. After waiting a few seconds the LED Setting Lighting should go off, if not, please try again. (After sending the Z-Wave NIF one time if the ZM1601 is not included it will send 4 times Network Wide Inclusion request every 4 ~ 6 seconds for auto inclusion. The orange LED will flash again if the siren has not been included or the orange LED will go off after inclusion.)",
-		"exclusion": "For “Exclusion” from (removing from) a network: Set up the Z-Wave™ network controller into “exclusion” mode, and following its instruction to delete the ZM 1601 from your controller. Press the program switch of ZM 1601 for 1 second at least & release to be excluded. Note: a. LED setting light will flash (orange color) continuously in Exclusion condition for 25 seconds. b. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
+		"inclusion": "For 'Inclusion' (adding to) a network, put the Z-Wave™ network controller into 'inclusion' mode, and following its instruction to add the ZM 1601 to your controller. To get the ZM 1601 in the 'inclusion' mode, open the bracket and press the program switch of ZM 1601 for 1 second at least & release to be included. After waiting a few seconds the LED Setting Lighting should go off, if not, please try again. (After sending the Z-Wave NIF one time if the ZM1601 is not included it will send 4 times Network Wide Inclusion request every 4 ~ 6 seconds for auto inclusion. The orange LED will flash again if the siren has not been included or the orange LED will go off after inclusion.)",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ network controller into 'exclusion' mode, and following its instruction to delete the ZM 1601 from your controller. Press the program switch of ZM 1601 for 1 second at least & release to be excluded. Note: a. LED setting light will flash (orange color) continuously in Exclusion condition for 25 seconds. b. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
 		"reset": "All user and network settings will be cleared and the device reset to factory defaults when the device is excluded",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1009/ZM%201601%20Siren_20140407-500%20series.pdf"
 	}

package/config/devices/0x0109/zm1602-5.json

@@ -83,9 +83,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZM 1602 to your controller. To get in the “inclusion” mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
-		"exclusion": "Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
-		"reset": "This device can’t be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1602 to your controller. To get in the 'inclusion' mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
+		"exclusion": "Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
+		"reset": "This device can't be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1276/ZM%201602-5%20Siren_R3_20170301.pdf"
 	}
 }

package/config/devices/0x0109/zm1602.json

@@ -77,8 +77,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZM 1602 to your controller. To get in the “inclusion” mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
-		"exclusion": "Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1602 to your controller. To get in the 'inclusion' mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
+		"exclusion": "Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
 		"reset": "This device can't be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1276/ZM%201602-5%20Siren_R3_20170301.pdf"
 	}

package/config/devices/0x0109/zm1611jp-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZM1611-5 to your controller. To get in the “inclusion” mode, press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be included. After setting, the LED should go off, if not, please try again. (After sending one time’s Z-Wave NIF and not be included then it will send 4 times NWI in every 30 seconds for auto inclusion. The LED will flash again if the U-Bell has not been included or the LED will go off after inclusion.)",
-		"exclusion": "For “Exclusion” from (removing from) a network: Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to remove the ZM1611-5 from your controller. Press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be excluded. The LED will flash again after exclusion",
-		"reset": "For \"Reset\": Press and hold the Program Switch for 5 seconds “at least”, power on until the LED turns on then release the switch, U-Bell will send Command Class Device Reset Locally for Reset Process. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM1611-5 to your controller. To get in the 'inclusion' mode, press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be included. After setting, the LED should go off, if not, please try again. (After sending one time's Z-Wave NIF and not be included then it will send 4 times NWI in every 30 seconds for auto inclusion. The LED will flash again if the U-Bell has not been included or the LED will go off after inclusion.)",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Set up the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZM1611-5 from your controller. Press and hold the program switch of ZM1611-5 for 3 seconds at least & release to be excluded. The LED will flash again after exclusion",
+		"reset": "For \"Reset\": Press and hold the Program Switch for 5 seconds 'at least', power on until the LED turns on then release the switch, U-Bell will send Command Class Device Reset Locally for Reset Process. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3572/ZM1611-5%20USER%20MANUAL.pdf"
 	}
 }

package/config/devices/0x0109/zm1621.json

@@ -65,8 +65,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZM 1621 to your controller. To get in the “inclusion” mode, get magnet of the bracket to touch the reed switch on the ZM1621 and separate at once to be included. After setting, the LED Light should go off, if not, please try again. (After sending one time’s Z-Wave NIF and not be included then it will send NWI for auto inclusion. The LED light will flash again if the siren has not been included or the LED light will go off after inclusion.)",
-		"exclusion": "For “Exclusion” in (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to remove the ZM 1621 from your controller. ZM1621-5 will send NWE if the exclusion could not be done successfully. \nNote:\na. LED light will flash continuously in Exclusion condition.\nb. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZM 1621 to your controller. To get in the 'inclusion' mode, get magnet of the bracket to touch the reed switch on the ZM1621 and separate at once to be included. After setting, the LED Light should go off, if not, please try again. (After sending one time's Z-Wave NIF and not be included then it will send NWI for auto inclusion. The LED light will flash again if the siren has not been included or the LED light will go off after inclusion.)",
+		"exclusion": "For 'Exclusion' in (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to remove the ZM 1621 from your controller. ZM1621-5 will send NWE if the exclusion could not be done successfully. \nNote:\na. LED light will flash continuously in Exclusion condition.\nb. All user and network settings will be cleared and the device reset to factory defaults when the device is excluded.",
 		"reset": "ZM 1621 will reset to factory default when the device has been excluded.\n(Please use this procedure only in the event that your network primary controllers is missing or otherwise inoperable!)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2992/ZM1621-5%20Outdoor%20Siren%20(SDK6.51.10).pdf"
 	}

package/config/devices/0x0109/zp3111-5.json

@@ -132,8 +132,8 @@
 	],
 	"metadata": {
 		"inclusion": "To add the ZP3111 to the Z-Wave network (inclusion), place the Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds.",
-		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
-		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
+		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"wakeup": "Press the Programm Switch once.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2479/ZP3111-5_R2_20170316.pdf"
 	}

package/config/devices/0x0109/zp3113-7.json

@@ -118,9 +118,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: To add the ZP3113 to your Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3113 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3113 will go to sleep after 30 seconds. The LED indicator will be flashing while the inclusion is continued",
-		"exclusion": "For “Exclusion” from (removing from) a network: To remove the ZP3113 from your Z-Wave network (exclusion), place your Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3113 to your controller. Press the Program Switch of ZP3113 once to be excluded.",
-		"reset": "Factory Default Reset: \nRemove cover to triggered tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3113 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' in (adding to) a network: To add the ZP3113 to your Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3113 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3113 will go to sleep after 30 seconds. The LED indicator will be flashing while the inclusion is continued",
+		"exclusion": "For 'Exclusion' from (removing from) a network: To remove the ZP3113 from your Z-Wave network (exclusion), place your Z-Wave primary controller into 'exclusion' mode, and following its instruction to delete the ZP3113 to your controller. Press the Program Switch of ZP3113 once to be excluded.",
+		"reset": "Factory Default Reset: \nRemove cover to triggered tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3113 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4314/ZP3113-7%204%20in%201%20PIR%20(Z-Wave%20certified)%20-%2020211004.pdf"
 	}
 }