@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x0109/zr1202.json

@@ -25,8 +25,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into“inclusion” mode and following its instruction to add the ZR1202 to your controller. To get into the “inclusion” mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the ZR1202 three times in 3 seconds. The LED should stop flashing, if not, please try again.",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZR1202 from your controller. Press the program switch on the ZR1202 three times in 3 seconds to be excluded.\nNote: LED setting light will flash continuously in Exclusion condition.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode and following its instruction to add the ZR1202 to your controller. To get into the 'inclusion' mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the ZR1202 three times in 3 seconds. The LED should stop flashing, if not, please try again.",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZR1202 from your controller. Press the program switch on the ZR1202 three times in 3 seconds to be excluded.\nNote: LED setting light will flash continuously in Exclusion condition.",
 		"reset": "Press Program Switch for 5 seconds, the ZR1202 will reset back to factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1325/ZR1202-5%20Repeater.pdf"
 	}

package/config/devices/0x0109/zs5101us-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZS 5101-5 to your controller. To get in the “inclusion” mode, please press the program switch of ZS 5101-5 for 1 second at least to be included. The LED on the ZS 5101-5 should go off, if not, please try again",
-		"exclusion": "Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZS 5101-5 from your controller. Press the program switch of ZS 5101-5 for 1 second at least to be excluded.",
-		"reset": "*Push the Tamper switch then power on (put in the battery) & hold the Tamper switch for 5 seconds, ZD5101-5 will send the “Device Reset Locally Notification” command and reset to the factory default, LED will solid on, need to take off the battery and re-put in the battery to complete the function.\n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS 5101-5 to your controller. To get in the 'inclusion' mode, please press the program switch of ZS 5101-5 for 1 second at least to be included. The LED on the ZS 5101-5 should go off, if not, please try again",
+		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS 5101-5 from your controller. Press the program switch of ZS 5101-5 for 1 second at least to be excluded.",
+		"reset": "*Push the Tamper switch then power on (put in the battery) & hold the Tamper switch for 5 seconds, ZD5101-5 will send the 'Device Reset Locally Notification' command and reset to the factory default, LED will solid on, need to take off the battery and re-put in the battery to complete the function.\n*Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2099/ZS%205101-5_V1_20160427.pdf"
 	}
 }

package/config/devices/0x0109/zs6101.json

@@ -26,8 +26,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZS6101-5 to your controller. To get in the “inclusion” mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6101-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZS6101-5 from your controller. Press the program switch of ZS6101-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6101-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6101-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
+		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6101-5 from your controller. Press the program switch of ZS6101-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1085/ZS%206101-5_ZS6102-5%20%20Smoke%20Detector.pdf"
 	}
 }

package/config/devices/0x0109/zs6102eu-5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZS6102-5 to your controller. To get in the “inclusion” mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6102-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
-		"exclusion": "Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZS6102-5 from your controller. Press the program switch of ZS6102-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
+		"inclusion": "Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6102-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of ZS6102-5 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)",
+		"exclusion": "Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6102-5 from your controller. Press the program switch of ZS6102-5 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition. (Please refer to the user manual to understand the program switch location)",
 		"reset": "ZS6102-5 will reset back to the factory default value after being excluded from the network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1084/ZS%206101-5_ZS6102-5%20%20Smoke.pdf"
 	}

package/config/devices/0x0109/zs6301-5.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZS6301-5 to your controller. To get in the “inclusion” mode, the distance between detector and controller is suggested to be in one meter. By power on to get included for first time or press the test switch of ZS6301-5 once to be included. After be included, the red LED will go on",
-		"exclusion": "For “Exclusion” from (removing from) a net work: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZS6301-5 from your controller. Press the test switch of ZS6301-5 once to be excluded.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the ZS6301-5 to your controller. To get in the 'inclusion' mode, the distance between detector and controller is suggested to be in one meter. By power on to get included for first time or press the test switch of ZS6301-5 once to be included. After be included, the red LED will go on",
+		"exclusion": "For 'Exclusion' from (removing from) a net work: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZS6301-5 from your controller. Press the test switch of ZS6301-5 once to be excluded.",
 		"reset": "N/A",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1328/ZS6301-5%20CO%20Detector.pdf"
 	}

package/config/devices/0x0109/zt1101.json

@@ -20,7 +20,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send “Device Reset Locally Notification” command and reset to the factory default. (Red LED flashes fast means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
+		"reset": "Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send 'Device Reset Locally Notification' command and reset to the factory default. (Red LED flashes fast means reset completely).\nRemark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1706/ZT1101-5%20Keyfob_R1_20150703.pdf"
 	}
 }

package/config/devices/0x0109/zw4111eu-5.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "3. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into“inclusion” mode, and following its instruction to add the ZW4111 to your controller. To get in the “inclusion” mode, press the program switch 3 times or outer switch 1 / switch 2 to be included. \nNOTE: The red LED will flash if ZW4111 has not been included before or the red LED will be OFF.",
-		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZW 4101 / ZW4111 from your controller. Press the program switch or outer switch 1 / switch 2 3 times to be excluded",
-		"reset": "Press Program Switch and power on till 5 seconds, ZW4111 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "3. For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into'inclusion' mode, and following its instruction to add the ZW4111 to your controller. To get in the 'inclusion' mode, press the program switch 3 times or outer switch 1 / switch 2 to be included. \nNOTE: The red LED will flash if ZW4111 has not been included before or the red LED will be OFF.",
+		"exclusion": "For 'Exclusion' from (removing from) a network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to delete the ZW 4101 / ZW4111 from your controller. Press the program switch or outer switch 1 / switch 2 3 times to be excluded",
+		"reset": "Press Program Switch and power on till 5 seconds, ZW4111 will send the 'Device Reset Locally Notification' command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1582/ZW%204111-5%20Curtain%20(Screw%20Terminal)%2020151124.pdf"
 	}
 }

package/config/devices/0x010a/01e06s263.json

@@ -141,9 +141,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Add the device to a certified Z-Wave network\nThe device supports both Classic Add (Classic Inclusion) and Network Wide Add (Network Wide Inclusion).\nThe device supports encryption S2 Unauthenticated.\nFollow the steps below to add the device to the network.\n1. Set primary controller into Add mode (please see controller instruction manual) and operate on it either to enable S2 Unauthenticated encryption or to disable encryption\n2. Check the device is not already added to the network (please refer to the manual section “How to check the device is added to the network”)\n3. Press and hold button N.1 located on top-left front-end device more then 4 seconds till button LED blinks shortly magenta or press shortly the Physical button located on the front-end top-back device (see section “Physical Button Operating” to locate Physical Button).\n4. Every device LED button blinks green shortly 3 times upon the device added successfully\n\nShould the device fail the Classic Add (Classic Inclusion) the device enters into Network Wide Add (Network Wide Inclusion) mode up to 4 times. Any time the device enters into Wide Add Mode, LED Button N.1 blinks Magenta and keeps on to emit a short beep.\n\nHow to check the device is added to the network\nPress button N.1 shortly. The LED button blinks red shortly whether the device is not added to the network",
-		"exclusion": "Remove the device from a certified Z-Wave network\n1. Set primary controller into Remove mode (please see controller instruction manual)\n2. Check the device is not already removed from the network (please refer to the manual section “How to check the device is added to the network”)\n3. Press and hold button N.1 located on top-left front-end device more then 6 seconds till the device emits a long beep. Release the button and press it shortly 3 times again or press shortly the Physical button located on the front end top-back device\n4. Button LED blinks red shortly upon the device removed successfully.\n5. Check the device is removed from the network (please refer to the manual section “How to check the device is added to the network”)\n\nHow to check the device is added to the network\nPress button N.1 shortly. The LED button blinks red shortly whether the device is not added to the network",
-		"reset": "Press and hold the Physical button for about 5 seconds till the buzzer plays a long beep, release the button and press it again till the buzzer plays a sequence of 3 short beeps, than release the button.\nWarning: don’t care the 2 short beeps played after 2 seconds from start and keep on pressing the button till the buzzer plays the 3 short beeps sequence.\nSee Factory reset below for more details and notes.\n\nFactory reset\nDuring factory reset the device sends a Device Reset Locally notification from the Lifeline group.\nThe device reverts to its factory default settings, blinking all LED buttons and reboots and send the Device Reset Locally Notification from the Lifeline group.\nDo not disconnect the device from power supply till rebooting is completed.\nConfiguration and settings are restore to default values.\nHome ID and Node ID are cleared as well",
+		"inclusion": "1. Press and hold button 1 for more than 4 seconds until the LED blinks magenta, or press the physical button on the back briefly\n2. All LED buttons will blink green 3 times when successfully included",
+		"exclusion": "1. Press and hold button 1 for more than 6 seconds until the device emits a long beep\n2. Release the button and press it 3 times quickly, or press the physical button on the back briefly\n3. Button LED will blink red when successfully excluded",
+		"reset": "Press and hold the physical button for about 5 seconds until the buzzer plays a long beep, release and press again until you hear 3 short beeps.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3271/Vitrum%20VI%20EU%20on-off%206%20triac%20868.4MHz%20User%20Manual.1.21.pdf"
 	}
 }

package/config/devices/0x010a/vitrum_i_dimmer.json

@@ -26,9 +26,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
+		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_i_switch.json

@@ -25,9 +25,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. LEDs will flash yellow 3 times and all outputs will switch on when successfully included.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds\n2. LED will flash red 3 times and sound a tone when successfully excluded",
+		"reset": "1. Remove the unit from the wall mounting box\n2. Press and hold the hidden factory reset button for at least 3 seconds\n3. LED will flash red 3 times and sound a tone when reset is complete",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_ii_dimmer.json

@@ -30,9 +30,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_ii_switch.json

@@ -29,9 +29,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
 		"manual": "https://www.manualslib.com/manual/1360869/Vitrum-On-Off-Wireless.html"
 	}
 }

package/config/devices/0x010a/vitrum_iii_eu_dimmer.json

@@ -28,9 +28,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
 		"manual": "https://z-wave.ru/podderzhka/skachat/category/83-thinksimple.html?download=231:vitrum-dimmer-wireless"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_i.json

@@ -20,9 +20,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_iv.json

@@ -32,9 +32,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset.",
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset.",
 		"manual": "https://docplayer.net/31994823-Vitrum-satellite-wireless-installation-and-operation.html"
 	}
 }

package/config/devices/0x010a/vitrum_satellite_vi.json

@@ -41,8 +41,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "1. Check the device is not already included in a Z-Wave network by pressing any button on the front panel: the LED button should blink with red colour brielfy. Should the device be already included, follow the exclusion instructions to exclude it from the network\n2. Set the controller into “Inclusion Mode”. Refer to the controller documentation to set the controller into Inclusion mode\n3. Touch any of the keys on Vitrum to include the unit.\n4. If adding succeeds, Vitrum will flash the LEDs yellow three times, and switch on all outputs.",
-		"exclusion": "1. The device can be excluded from a network only if previously included. Check that by pressing a button on the front panel: the LED button should not blink with red colour brielfy.\n2. Set the controller into “Exclusion Mode”. Refer to the controller documentation to set the controller into Exclusion mode.\n 3. Press and hold the top left most button for at least 8 seconds.\n 4. LED will flash red three times and sound a tone to confirm successful exclusion.",
-		"reset": "WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable.\nTo reset the unit to Factory Settings:\n1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm successful factory reset."
+		"inclusion": "1. Touch any key on the device.\n2. The device will flash LEDs yellow three times and switch on all outputs if inclusion succeeds.",
+		"exclusion": "1. Press and hold the top left button for at least 8 seconds.\n2. LED will flash red three times and sound a tone to confirm exclusion.",
+		"reset": "1. Remove the unit from the wall mounting box.\n2. Press and hold the hidden Factory Reset button for at least 3 seconds.\n3. LED will flash red three times and sound a tone to confirm factory reset."
 	}
 }

package/config/devices/0x010b/dn3e6ja087.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "When you tap the Setting button in Moble Application, Settings dialog is displayed. Then select \"Reset\" and press “RESET” button in Factory Default Reset dialog. This will reset the Z-Wave chip and all LEDs blinks, and the product will broadcast the “DEVICE RESET LOCALLY NOTIFICATION” after restart.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Tap the Setting button in the mobile application.\n2. Select \"Reset\" and press 'RESET' button in Factory Default Reset dialog.\n3. All LEDs will blink when reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2787/UsersGuide_DN3E6JE087_20171225.pdf"
 	}
 }

package/config/devices/0x010b/dn3e6je074.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "When you tap the Setting button in Moble Application, Settings dialog is displayed. Then select \"Reset\" and press “RESET” button in Factory Default Reset dialog. This will reset the Z-Wave chip and all LEDs blinks, and the product will broadcast the “DEVICE RESET LOCALLY NOTIFICATION” after restart.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Tap the Setting button in the mobile application.\n2. Select \"Reset\" and press 'RESET' button in Factory Default Reset dialog.\n3. All LEDs will blink when reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2606/UsersGuide_20171122.pdf"
 	}
 }

package/config/devices/0x010b/dn3e6je088.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "When you tap the Setting button in Moble Application, Settings dialog is displayed. Then select \"Reset\" and press “RESET” button in Factory Default Reset dialog. This will reset the Z-Wave chip and all LEDs blinks, and the product will broadcast the “DEVICE RESET LOCALLY NOTIFICATION” after restart.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Tap the Setting button in the mobile application.\n2. Select \"Reset\" and press 'RESET' button in Factory Default Reset dialog.\n3. All LEDs will blink when reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2782/UsersGuide_DN3E6JE088_20171225.pdf"
 	}
 }

package/config/devices/0x010b/dn3e6je089.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "When you tap the Setting button in Moble Application, Settings dialog is displayed. Then select \"Reset\" and press “RESET” button in Factory Default Reset dialog. This will reset the Z-Wave chip and all LEDs blinks, and the product will broadcast the “DEVICE RESET LOCALLY NOTIFICATION” after restart.\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Tap the Setting button in the mobile application.\n2. Select \"Reset\" and press 'RESET' button in Factory Default Reset dialog.\n3. All LEDs will blink when reset is complete.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2999/UsersGuide_20180627.pdf"
 	}
 }

package/config/devices/0x010b/dn3g6ja069.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Insert a CR123A, and LED blinks. \nSet the controller to the status for “Add”.\nPress the button over 3 seconds and release.\nAbout 30 second later, LED turns off when “Add” is completed.",
-		"exclusion": "Set the controller to the status for “Remove”.\nPress the button over 3 seconds and release.\nLED blinks when “Remove” is completed.",
-		"reset": "Press the button over 10 seconds and release",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2852/UsersGuide%20DN3G6JA069%20rev1.pdf"
 	}
 }

package/config/devices/0x010b/dn3g6ja082.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "-Add (Inclusion)\nInsert a CR123A, and LED blinks. \nSet the controller to the status for “Add”. \nPress the button over 3 seconds and release.\nAbout “Add” is completed, LED turns off.\n(If security include, LED turns off will soon after “Preparing inclusion” process.)\nNote) After inclusion completed, this sensor keep waking about 40 seconds, for interview process.\n During this time, button operation is disabled.",
-		"exclusion": "-Remove (exclusion)\nSet the controller to the status for “Remove”.\nPress the button over 3 seconds and release.\nLED blinks when “Remove” is completed.",
-		"reset": "Press the button over 10 seconds and release.\nPlease use this procedure only when the network primary controller like the gateway is missing or otherwise inoperable",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2979/UsersGuide%20DN3G6JA082%20rev1.pdf"
 	}
 }

package/config/devices/0x010b/dn3g6ja084.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "-Add (Inclusion)\nInsert a CR123A, and LED blinks. \nSet the controller to the status for “Add”. \nPress the button over 3 seconds and release.\nAbout “Add” is completed, LED turns off.\n(If security include, LED turns off will soon after “Preparing inclusion” process.)\nNote) After inclusion completed, this sensor keep waking about 40 seconds, for interview process.\n During this time, button operation is disabled.",
-		"exclusion": "-Remove (exclusion)\nSet the controller to the status for “Remove”.\nPress the button over 3 seconds and release.\nLED blinks when “Remove” is completed.",
-		"reset": "Press the button over 10 seconds and release.\nPlease use this procedure only when the network primary controller like the gateway is missing or otherwise inoperable",
+		"inclusion": "1. Insert a CR123A battery and LED blinks.\n2. Press the button for over 3 seconds and release.\n3. LED turns off when inclusion is completed.",
+		"exclusion": "1. Press the button for over 3 seconds and release.\n2. LED blinks when exclusion is completed.",
+		"reset": "Press the button for more than 10 seconds and release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2980/UsersGuide%20DN3G6JA084%20rev1.pdf"
 	}
 }

package/config/devices/0x010e/btzw125.json

@@ -270,9 +270,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add or include the danalock into a Z-Wave network\nSet the controller in inclusion mode\nTouch the User Button until you hear two beeps.",
-		"exclusion": "To remove or exclude the danalock into a Z-Wave network\nSet the controller in exclusion mode\nTouch the User Button until you hear two beeps",
-		"reset": "The danalock can be set to factory settings by holding the User Button for ten beeps. Please use this procedure only when the primary controller is missing or otherwise inoperable",
+		"inclusion": "Touch the User Button until you hear two beeps",
+		"exclusion": "Touch the User Button until you hear two beeps",
+		"reset": "Hold the User Button for ten beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1238/Danalock%20Product%20manual.pdf"
 	}
 }

package/config/devices/0x010e/danalock_v3-btze.json

@@ -106,9 +106,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Set the controller in inclusion mode\n2. Push the switch once.\n3. Wait 5 seconds",
-		"exclusion": "1. Set the controller in exclusion mode\n2. Push the switch once.\n3. Wait 5 seconds",
-		"reset": "The Danalock can be set to factory settings by pushing the switch ten times. Please use this procedure only when the primary controller is missing or otherwise inoperable",
+		"inclusion": "Push the switch once. Wait 5 seconds",
+		"exclusion": "Push the switch once. Wait 5 seconds",
+		"reset": "Push the switch ten times",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4295/Danalock_V3_Product_manual_Z_Wave_V_0.9.5.pdf"
 	}
 }

package/config/devices/0x010f/fgbs222.json

@@ -398,9 +398,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to the Z-Wave network manually:\n1. Power the device.\n2. Set the main controller in (Security/non-Security Mode) add mode\n(see the controller’s manual).\n3. Quickly, triple click button on the device housing or switch\nconnected to IN1 or IN2.\n4. If you are adding in Security S2 Authenticated, scan the DSK QR\ncode or input the 5-digit PIN code (label on the bottom of the box).\n5. LED will start blinking yellow, wait for the adding process to end.\n6. Successful adding will be confirmed by the Z-Wave controller’s\nmessage",
-		"exclusion": "Removing (Exclusion) – Z-Wave device learning mode, allowing to\nremove the device from existing Z-Wave network. Removing also results\nin resetting the device to factory defaults.\nTo remove the device from the Z-Wave network:\n1. Power the device.\n2. Set the main controller into remove mode (see the controller’s\nmanual).\n3. Quickly, triple click button on the device housing or switch\nconnected to IN1 or IN2.\n4. LED will start blinking yellow, wait for the removing process to\nend.\n5. Successful removing will be confirmed by the Z-Wave controller’s\nmessage",
-		"reset": "Reset procedure allows to restore the device back to its factory settings,\nwhich means all information about the Z-Wave controller and\nuser configuration will be deleted.\nResetting the device is not the recommended way of\nremoving the device from the Z-Wave network. Use reset\nprocedure only if the primary controller is missing or\ninoperable. Certain device removal can be achieved by the\nprocedure of removing described.\n1. Press and hold the button to enter the menu.\n2. Release button when the device glows yellow.\n3. Quickly click the button to confirm.\n4. After few seconds the device will be restarted, which is signalled\nwith the red colour",
+		"inclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful adding will be confirmed by the LED indicator.",
+		"exclusion": "1. Power the device.\n2. Quickly triple click the button on the device housing or switch connected to IN1 or IN2.\n3. LED will start blinking yellow.\n4. Successful removing will be confirmed by the LED indicator.",
+		"reset": "1. Press and hold the button to enter the menu.\n2. Release button when the device glows yellow.\n3. Quickly click the button to confirm.\n4. After few seconds the device will be restarted, which is signalled with the red colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4153/FGBS-222-T-EN-1.2.pdf"
 	}
 }

package/config/devices/0x010f/fgd211.json

@@ -386,7 +386,7 @@
 			"#": "40",
 			"$if": "firmwareVersion >= 1.9 && firmwareVersion <= 2.0",
 			"label": "Updating the Dimming Level without Switch",
-			"description": "Parameter’s value changes depending on the dimming level.",
+			"description": "Parameter's value changes depending on the dimming level.",
 			"valueSize": 1,
 			"minValue": 0,
 			"maxValue": 255,

package/config/devices/0x010f/fgfs101.json

@@ -378,15 +378,15 @@
 					"value": 0
 				},
 				{
-					"label": "2nd group ”Control” sent as secure",
+					"label": "2nd group 'Control' sent as secure",
 					"value": 1
 				},
 				{
-					"label": "3rd group ”Alarm” sent as secure",
+					"label": "3rd group 'Alarm' sent as secure",
 					"value": 2
 				},
 				{
-					"label": "4th group ”Tamper” sent as secure",
+					"label": "4th group 'Tamper' sent as secure",
 					"value": 3
 				}
 			]

package/config/devices/0x010f/fggc001.json

@@ -165,7 +165,7 @@
 		{
 			"#": "10",
 			"label": "Scenes Sent to the Controller",
-			"description": "Defines which actions result in sending scenes to 1st “Lifeline” group.",
+			"description": "Defines which actions result in sending scenes to 1st 'Lifeline' group.",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 63,
@@ -212,30 +212,30 @@
 			"defaultValue": 31,
 			"options": [
 				{
-					"label": "2nd group ”Flick up” sent as secure",
+					"label": "2nd group 'Flick up' sent as secure",
 					"value": 1
 				},
 				{
-					"label": "3rd group ”Flick down” sent as secure",
+					"label": "3rd group 'Flick down' sent as secure",
 					"value": 2
 				},
 				{
-					"label": "4th group \"Flick left” sent as secure",
+					"label": "4th group \"Flick left' sent as secure",
 					"value": 4
 				},
 				{
-					"label": "5th group \"Flick right” sent as secure",
+					"label": "5th group \"Flick right' sent as secure",
 					"value": 8
 				},
 				{
-					"label": "6th group \"Circular airWheel” sent as secure",
+					"label": "6th group \"Circular airWheel' sent as secure",
 					"value": 16
 				}
 			]
 		},
 		{
 			"#": "12",
-			"label": "Mode of 2nd-5th \"Flick UP/DOWN/LEFT/RIGHT”",
+			"label": "Mode of 2nd-5th \"Flick UP/DOWN/LEFT/RIGHT'",
 			"description": "Choose control mode for 2nd-5th groups and scenes.",
 			"valueSize": 1,
 			"minValue": 1,

package/config/devices/0x010f/fgpb101.json

@@ -449,9 +449,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1) Place the Button within the direct range of your Z-Wave controller.\n2) Set the main controller in (security/non-security) add mode (see the controller’s manual).\n3) Click the Button at least six times.\n4) Wait for the adding process to end.\n5) Successful adding will be confirmed by the Z-Wave controller’s message.",
-		"exclusion": "1) Place the Button within the direct range of your Z-Wave controller.\n2) Set the main controller in remove mode (see the controller’s manual).\n3) Click the Button at least six times.\n4) Wait for the removing process to end.\n5) Successful removing will be confirmed by the Z-Wave controller’s message.",
-		"reset": "Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device:\n1) Click the Button exactly five times.\n2) Press and hold the Button for at least 5 seconds.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
+		"exclusion": "1. Place the Button within the direct range of your Z-Wave controller.\n2. Click the Button at least six times.",
+		"reset": "1. Click the Button exactly five times.\n2. Press and hold the Button for at least 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3486/tech_panic_en_9.pdf"
 	}
 }

package/config/devices/0x010f/fgr-224.json

@@ -257,9 +257,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To add the device to the Z-Wave network manually:\n1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Set the main controller in (Security/non-Security Mode) add\nmode (see the controller’s manual).\n4. Quickly, click PROG button three times. Optionally, click S1 or S2\nthree times.\n5. If you are adding in Security S2 Authenticated, input the PIN\nCode (label on the device, also underlined part of the DSK on t he\nlabel on the bottom of the box).\n6. Wait for the LED indicator to blink yellow.\n7. Successful adding will be confirmed by the Z-Wave controller’s\nmessage and the device’s LED indicator:\n• Green – successful (non-secure, S0, S2 non-authenticated),\n• Magenta – successful (Security S2 Authenticated),\n• Red – not successful",
-		"exclusion": "Removing (Exclusion) – Z-Wave device learning mode, allowing to\nremove the device from existing Z-Wave network.\nTo remove the device from the Z-Wave network:\n1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Set the main controller in remove mode (see the controller’s\nmanual).\n4. Quickly, click PROG button three times. Optionally, click S1 or S2\nthree times within 10 minutes of powering up the device.\n5. Wait for the removing process to end.\n6. Successful removing will be confirmed by the Z-Wave controller’s\nmessage and the device’s LED indicator - Red.\n7. Removing the device from the Z-Wave network doesn’t cause\nfactory reset",
-		"reset": "Reset procedure allows to restore the device back to its factor y\nsettings, which means all information about the Z-Wave controller\nand user configuration will be deleted.\n1. Switch off the mains voltage (disable the fuse).\n2. Remove the device from the wall switch box.\n3. Switch on the mains voltage.\n4. Press and hold the PROG button to enter the menu.\n5. Wait for the LED indicator to glow yellow.\n6. Quickly release and click the PROG button again.\n7. During the factory reset, the LED indicator will blink yellow.\n8. After few seconds the device will be restarted, which is signal led\nwith the red LED indicator colour",
+		"inclusion": "1. Power the device.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times.\n4. LED indicator will blink yellow.\n5. Successful adding will be confirmed by the device's LED indicator: Green (non-secure, S0, S2 non-authenticated), Magenta (Security S2 Authenticated), Red (not successful).",
+		"exclusion": "1. Make sure the device is powered.\n2. Identify the PROG button or the S1/S2 switches.\n3. Quickly click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device.\n4. Successful removing will be confirmed by the device's LED indicator - Red.",
+		"reset": "1. Switch off the mains voltage (disable the fuse).\n2. Remove the device from the wall switch box.\n3. Switch on the mains voltage.\n4. Press and hold the PROG button to enter the menu.\n5. Wait for the LED indicator to glow yellow.\n6. Quickly release and click the PROG button again.\n7. During the factory reset, the LED indicator will blink yellow.\n8. After few seconds the device will be restarted, which is signalled with the red LED indicator colour.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/948/FGR-224-T-EN-v1.22.pdf"
 	}
 }

package/config/devices/0x010f/fgwp102.json

@@ -32,7 +32,7 @@
 	"paramInformation": [
 		{
 			"#": "1",
-			"label": "“Always On” Mode",
+			"label": "'Always On' Mode",
 			"description": "Will turn on connected device permanently",
 			"valueSize": 1,
 			"defaultValue": 0,
@@ -158,7 +158,7 @@
 		{
 			"#": "20",
 			"$if": "firmwareVersion >= 3.2",
-			"label": "On/Off (Button)” Association Group (2)",
+			"label": "On/Off (Button)' Association Group (2)",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,
@@ -229,7 +229,7 @@
 		{
 			"#": "24",
 			"$if": "firmwareVersion >= 3.2",
-			"label": "SWITCH ON Value - „On/Off” Association Groups",
+			"label": "SWITCH ON Value - „On/Off' Association Groups",
 			"valueSize": 2,
 			"minValue": 0,
 			"maxValue": 255,

package/config/devices/0x010f/templates/fibaro_template.json

@@ -1,8 +1,8 @@
 {
 	"default_metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, quickly press key S1 or B-button on product's housing three times",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, quickly press key S1 or B-button on product's housing three times",
-		"reset": "1. Power-cycle the device\n2. Press and hold the B-button to enter the menu\n3. Wait for the LED to turn yellow\n4. Quickly release and click B-button again\n5. Device will restart and LED will turn red"
+		"inclusion": "Quickly press key S1 or B-button on product's housing three times.",
+		"exclusion": "Quickly press key S1 or B-button on product's housing three times.",
+		"reset": "1. Power-cycle the device\n2. Press and hold the B-button to enter the menu\n3. LED will turn yellow\n4. Quickly release and click B-button again\n5. Device will restart and LED will turn red"
 	},
 	"send_secure_commands_group2": {
 		"$import": "~/templates/master_template.json#base_enable_disable",

package/config/devices/0x0112/itb-5088.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Press “RESET” in the Factory Default Reset dialog. This will reset\nthe Z- Wave chip, and the gateway will show “DEVICE RESET\nLOCALLY NOTIFICATION” after the restart.\nIf this controller is the primary controller for your network,\nresetting it will result in the nodes in your network becoming\norphaned, and it will be necessary after the reset to exclude and\nre-include all of the nodes in the network. If this controller is being\nused as a secondary controller in the network, use this procedure\nto reset this controller only in the event that the network primary\ncontroller is missing or otherwise inoperable",
+		"reset": "Press 'RESET' in the Factory Default Reset dialog. This will reset\nthe Z- Wave chip, and the gateway will show 'DEVICE RESET\nLOCALLY NOTIFICATION' after the restart.\nIf this controller is the primary controller for your network,\nresetting it will result in the nodes in your network becoming\norphaned, and it will be necessary after the reset to exclude and\nre-include all of the nodes in the network. If this controller is being\nused as a secondary controller in the network, use this procedure\nto reset this controller only in the event that the network primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3200/HOMEOSV-ex_UsersGuide.pdf"
 	}
 }