@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x0455/ora-zrx.json

@@ -269,8 +269,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1) Prepare the Z-Wave controller for inclusion of a device (see your controller’s instructions).\n2) On the motor, run the programming sequence for inclusion:\na. By the remote control: AB - AC - AB (2 seconds), wait for confirmation movements.\nb. By the button (if the end stops are not adjusted, you can use either sequence indifferently):\ni. With the motor on the high limit switch: UP-UP-UP-UP-UP-DOWN.\nii. With the motor on the low limit switch: DOWN-DOWN-DOWN-DOWN-DOWN-UP.\n3) The motor performs a few short movements to signal that the inclusion procedure is in progress.\n4) Check the controller to verify that the procedure was successful.",
-		"exclusion": "1) Prepare the Z-Wave controller for exclusion of a device (see your controller’s instructions).\n2) On the motor, run the programming sequence for exclusion:\na. By the remote control: AB - AC - AB (2 seconds), wait for confirmation movements.\nb. By the button (if the end stops are not adjusted, you can use either sequence indifferently):\ni. With the motor on the high limit switch: UP-UP-UP-UP-UP-DOWN.\nii. With the motor on the low limit switch: DOWN-DOWN-DOWN-DOWN-DOWN-UP.\n3) The motor performs a few short movements to signal that the exclusion procedure is in progress.\n4) Check the controller to verify that the procedure was successful.",
+		"inclusion": "1) Prepare the Z-Wave controller for inclusion of a device (see your controller's instructions).\n2) On the motor, run the programming sequence for inclusion:\na. By the remote control: AB - AC - AB (2 seconds), wait for confirmation movements.\nb. By the button (if the end stops are not adjusted, you can use either sequence indifferently):\ni. With the motor on the high limit switch: UP-UP-UP-UP-UP-DOWN.\nii. With the motor on the low limit switch: DOWN-DOWN-DOWN-DOWN-DOWN-UP.\n3) The motor performs a few short movements to signal that the inclusion procedure is in progress.\n4) Check the controller to verify that the procedure was successful.",
+		"exclusion": "1) Prepare the Z-Wave controller for exclusion of a device (see your controller's instructions).\n2) On the motor, run the programming sequence for exclusion:\na. By the remote control: AB - AC - AB (2 seconds), wait for confirmation movements.\nb. By the button (if the end stops are not adjusted, you can use either sequence indifferently):\ni. With the motor on the high limit switch: UP-UP-UP-UP-UP-DOWN.\nii. With the motor on the low limit switch: DOWN-DOWN-DOWN-DOWN-DOWN-UP.\n3) The motor performs a few short movements to signal that the exclusion procedure is in progress.\n4) Check the controller to verify that the procedure was successful.",
 		"reset": "1) From the remote control: AB - AC - BC (4 seconds), wait for confirmation movements to be executed.\n2) From the button (if the end stops are not adjusted, you can use either sequence indifferently):\na. With the motor on the high limit switch: UP-UP-UP-DOWN-UP-DOWN.\nb. With the motor on the low limit switch: DOWN-DOWN-DOWN-UP-DOWN-UP.\nINFO: If the reset is performed while the device is still part of a network, it notifies the other devices in the lifeline group that it has been removed.",
 		"manual": "https://www.cherubini-group.com/Content/uploads/2021/10/ORA_A4518_6N14_EN.pdf"
 	}

package/config/devices/0x0458/61303_zw3010.json

@@ -67,7 +67,7 @@
 	"metadata": {
 		"inclusion": "Adding your device to a Z-Wave network\n1. Follow the instructions for your Z-Wave certified controller to\nadd a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press\nand release the top or bottom of the wireless smart dimmer\n(rocker)",
 		"exclusion": "To remove and reset the device\n1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press\nand release the top or bottom of the wireless smart dimmer\n(rocker)",
-		"reset": "1. Quickly press ON (top) button three times then immediately\npress the OFF (bottom) button three times. The LED will flash\nON/OFF five times when completed successfully.\nNote: This should only be used if your network’s primary\ncontroller is missing or otherwise inoperable",
+		"reset": "1. Quickly press ON (top) button three times then immediately\npress the OFF (bottom) button three times. The LED will flash\nON/OFF five times when completed successfully.\nNote: This should only be used if your network's primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4319/61303-1%20EnFrSp%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x5254/zrc-90.json

@@ -29,9 +29,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Press “L+R” buttons simultaneously until LED light up to add the device into ZRC-90 Z-Wave network",
-		"exclusion": "Click once on the “R” button to remove the device from ZRC-90 Z-Wave network",
-		"reset": "Press and keep holding “R” button not less than 10 seconds.\nRelease “R” button then triple click on “R” button within 2 seconds",
+		"inclusion": "Press 'L+R' buttons simultaneously until LED light up to add the device into ZRC-90 Z-Wave network",
+		"exclusion": "Click once on the 'R' button to remove the device from ZRC-90 Z-Wave network",
+		"reset": "Press and keep holding 'R' button not less than 10 seconds.\nRelease 'R' button then triple click on 'R' button within 2 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1584/F-BW8510xx%20(ZRC-90xx)%20User%20Manual_V1.01_20151030.pdf"
 	}
 }

package/config/devices/0x5254/zrp-200jp.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1 Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode \n2 When it is prompted to enter it, please triple click the “PROG” button within 1 second. Blue Indicator flashes TWICE then stay off",
-		"exclusion": "1 Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode \n2 When it is prompted to enter it, please triple click the “PROG” button within 1 second. Blue Indicator flashes TWICE then stay off",
-		"reset": "Press and Hold “PROG” button for 3 seconds on Z-Wave Slim Repeater, the indicator will light up Purple Color. DO NOT Release the “PROG” Button until indicator change back to Blue color and flashes TWICE.\n\nRemark : All the Setting and Data will be permanently deleted.\n \n*Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "1 Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode \n2 When it is prompted to enter it, please triple click the 'PROG' button within 1 second. Blue Indicator flashes TWICE then stay off",
+		"exclusion": "1 Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode \n2 When it is prompted to enter it, please triple click the 'PROG' button within 1 second. Blue Indicator flashes TWICE then stay off",
+		"reset": "Press and Hold 'PROG' button for 3 seconds on Z-Wave Slim Repeater, the indicator will light up Purple Color. DO NOT Release the 'PROG' Button until indicator change back to Blue color and flashes TWICE.\n\nRemark : All the Setting and Data will be permanently deleted.\n \n*Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2841/BW8180JP%20ZRP-200JP%20Installation%20Guide.pdf"
 	}
 }

package/config/devices/0x5254/zxt-600.json

@@ -288,6 +288,6 @@
 	"metadata": {
 		"inclusion": "When it is prompted to enter it, please triple click the PROG button within 1 second. Green Indicator flashes TWICE then stay off.",
 		"exclusion": "When it is prompted to enter it, please triple click the PROG button within 1 second. Green Indicator flashes TWICE then stay off.",
-		"reset": "Press and Hold “PROG” button for 3 seconds on AC Master, the Green Indicator will light up. DO NOT Release the “PROG” Button until Green Indicator flashes TWICE."
+		"reset": "Press and Hold 'PROG' button for 3 seconds on AC Master, the Green Indicator will light up. DO NOT Release the 'PROG' Button until Green Indicator flashes TWICE."
 	}
 }

package/config/devices/0x5254/zxt-800.json

@@ -230,9 +230,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Classic inclusion\nRefer to your primary controller to enter into the Inclusion Mode or Exclusion Mode\nOnce the primary controller is ready to include/exclude the device, press the “PROG” button once",
-		"exclusion": "Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode\nOnce the primary controller is ready to include/exclude the device, press the “PROG” button once",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable\nPress and keep holding “PROG” button not less than 10 seconds:\nLED will light up at first 5 seconds, LED flashes twice then stay off after reset process completed",
+		"inclusion": "Classic inclusion\nRefer to your primary controller to enter into the Inclusion Mode or Exclusion Mode\nOnce the primary controller is ready to include/exclude the device, press the 'PROG' button once",
+		"exclusion": "Refer to your primary controller to enter into the Inclusion Mode or Exclusion Mode\nOnce the primary controller is ready to include/exclude the device, press the 'PROG' button once",
+		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable\nPress and keep holding 'PROG' button not less than 10 seconds:\nLED will light up at first 5 seconds, LED flashes twice then stay off after reset process completed",
 		"manual": "https://remotec.com.hk/wp-content/uploads/2023/07/ZXT-800_USER_MANUAL_V1.0.pdf"
 	}
 }

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "@zwave-js/config",
-  "version": "15.6.0",
+  "version": "15.7.0",
   "description": "zwave-js: configuration files",
   "keywords": [],
   "publishConfig": {
@@ -77,13 +77,13 @@
     "test:dirty": "tsx ../maintenance/src/resolveDirtyTests.ts --run"
   },
   "dependencies": {
-    "@zwave-js/core": "15.6.0",
-    "@zwave-js/shared": "15.4.0",
+    "@zwave-js/core": "15.7.0",
+    "@zwave-js/shared": "15.7.0",
     "alcalzone-shared": "^5.0.0",
     "ansi-colors": "^4.1.3",
     "json-logic-js": "^2.0.5",
     "json5": "^2.2.3",
-    "pathe": "^2.0.1",
+    "pathe": "^2.0.3",
     "semver": "^7.6.3",
     "winston": "^3.17.0"
   },
@@ -92,21 +92,21 @@
     "@microsoft/api-extractor": "^7.52.2",
     "@types/js-levenshtein": "^1.1.3",
     "@types/json-logic-js": "^2.0.8",
-    "@types/node": "^20.17.32",
+    "@types/node": "^20.17.57",
     "@types/semver": "^7.7.0",
     "@types/sinon": "^17.0.4",
     "@types/xml2js": "^0.4.14",
     "@types/yargs": "^17.0.33",
-    "@zwave-js/maintenance": "15.6.0",
+    "@zwave-js/maintenance": "15.7.0",
     "comment-json": "^4.2.5",
     "del-cli": "^6.0.0",
     "es-main": "^1.3.0",
     "js-levenshtein": "^1.1.6",
-    "ky": "^1.7.2",
+    "ky": "^1.8.1",
     "peggy": "^3.0.2",
-    "sinon": "^19.0.2",
+    "sinon": "^20.0.0",
     "ts-pegjs": "patch:ts-pegjs@npm%3A4.2.1#~/.yarn/patches/ts-pegjs-npm-4.2.1-0f567a1059.patch",
-    "tsx": "^4.19.3",
+    "tsx": "^4.19.4",
     "typescript": "5.8.3",
     "vitest": "^2.1.9",
     "xml2js": "^0.6.2",