@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x027a/zen15.json

@@ -322,7 +322,7 @@
 	"metadata": {
 		"inclusion": "Please include the Power Switch to your network BEFORE connecting it to the appliance you wish to control.\n\nAuto Z-Wave Inclusion:\n1. Put your Z-Wave controller into inclusion mode\n2. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n3. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included\n4. A new on / off device will be recognized by your Z-Wave controller\n\nManual Z-Wave Inclusion:\n1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n2. Put your Z-Wave controller into inclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included\n5. A new on / off device will be recognized by your Z-Wave controller\n\nSecure Z-Wave Inclusion:\n1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller\n2. Put your Z-Wave controller in secure inclusion mode\nPress and HOLD the Z-Wave button for at least 3 seconds\n3. The LED indicator will start flashing green, then turn blue (on) or pink (off) once included\n4. A new secure on / off device will be recognized by your Z-Wave controller",
 		"exclusion": "1. Plug the Power Switch into a grounded receptacle located within direct range of your Z-Wave gateway controller\n2. Put your Z-Wave controller into exclusion mode\n3. Press and release the Z-Wave button 3 TIMES QUICKLY\n4. The LED indicator will start flashing orange, then turn blue (on) or pink (off) once excluded\n5. The Power Switch will disappear from your controller's device list. The LED indicator will remain solid orange for a few seconds to indicate exclusion\n\nIf the first attempt is unsuccessful, please repeat the process following all steps carefully",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the Power Switch into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset. The Power Switch will then turn off.\n\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory. You may only reset your Power Switch once it has been included to a Z-Wave network",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the Power Switch into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset. The Power Switch will then turn off.\n\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory. You may only reset your Power Switch once it has been included to a Z-Wave network",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2517/zooz-z-wave-plus-power-switch-zen15-user-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen20.json

@@ -290,9 +290,9 @@
 		"preserveRootApplicationCCValueIDs": true
 	},
 	"metadata": {
-		"inclusion": "1. Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub) \n2. Initiate inclusion (pairing) in the app (or web interface). \n3. CLICK CH1 BUTTON 3 TIMES QUICKLY. All LED indicators will start flashing \n4. You will see 7 or 8 new on/off devices in your app: 5 channels or on/off control, 2 channels for on/off monitoring (USB ports reporting charging/ charged status, no control), and possibly one master node to access and adjust advanced settings in.",
+		"inclusion": "1. Plug the Power Strip into a grounded receptacle you're planning to use it at (it doesn't need to be close to the hub) \n2. Initiate inclusion (pairing) in the app (or web interface). \n3. CLICK CH1 BUTTON 3 TIMES QUICKLY. All LED indicators will start flashing \n4. You will see 7 or 8 new on/off devices in your app: 5 channels or on/off control, 2 channels for on/off monitoring (USB ports reporting charging/ charged status, no control), and possibly one master node to access and adjust advanced settings in.",
 		"exclusion": "1. Bring the strip within direct range of your Z-Wave gateway (hub). \n2. Put the Z-Wave hub into exclusion mode. \n3. Press and release the CH1 button 3 times quickly. \n4. Your hub will confirm exclusion and all of the channels (child outlets) and the main device will disappear from your controller's device list.",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset \nthe device to factory settings. To complete the reset process manually, \nclick-click-click’n’hold CH1 button for at least 10 seconds. All LED indicators \nwill flash to confirm successful reset. NOTE: All previously recorded activity \nand custom settings EXCEPT for the kWh record will be erased from the device’s memory.",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset \nthe device to factory settings. To complete the reset process manually, \nclick-click-click'n'hold CH1 button for at least 10 seconds. All LED indicators \nwill flash to confirm successful reset. NOTE: All previously recorded activity \nand custom settings EXCEPT for the kWh record will be erased from the device's memory.",
 		"manual": [
 			{
 				"$if": "firmwareVersion >= 4.10",

package/config/devices/0x027a/zen21.json

@@ -128,7 +128,7 @@
 	"metadata": {
 		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
 		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the dimmer 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3667/zooz-z-wave-plus-on-off-switch-zen21-ver3.1-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen26.json

@@ -122,7 +122,7 @@
 	"metadata": {
 		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the switch 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
 		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the switch 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3147/zooz-z-wave-plus-s2-on-off-switch-zen26-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen27.json

@@ -181,7 +181,7 @@
 	"metadata": {
 		"inclusion": "1. Initiate inclusion mode on the Z-Wave hub.\n2. Tap the upper paddle of the dimmer 3 times quickly. The LED indicators will blink to signal communication and remain on for 2 seconds to confirm inclusion",
 		"exclusion": "1. Initiate exclusion mode on the Z-Wave hub.\n2. Tap the lower paddle on the dimmer 3 times quickly\n3. Your hub will confirm exclusion and the device will disappear from your controller's device list",
-		"reset": "1. Tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
+		"reset": "1. Tap-tap-tap'n'hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3148/zooz-z-wave-plus-s2-dimmer-switch-zen27-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen34.json

@@ -173,7 +173,7 @@
 		"inclusion": "Put your Z-Wave hub into inclusion mode and click the upper paddle 6 times quickly. The LED indicator\nwill blink blue during the process and light up green once added successfully. It will light up red if failed",
 		"exclusion": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the lower paddle 6 times very quickly\n4. Your hub will confirm exclusion and the device will disappear from your controller's device list",
 		"wakeup": "1. Bring the Remote Switch within direct range of your Z-Wave gateway (hub).\n2. Click the upper paddle 7 times very quickly\n3. Your device's indicator light will remain on to indicate that the device is awake.",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the process, make sure the device is powered, then tap-tap-\ntap’and’hold the upper paddle. The LED indicator will blink red 5 times to indicate successful reset",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the process, make sure the device is powered, then tap-tap-\ntap'and'hold the upper paddle. The LED indicator will blink red 5 times to indicate successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4114/zooz-700-series-remote-switch-zen34-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zen71.json

@@ -141,7 +141,7 @@
 	"metadata": {
 		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. Finalize inclusion at the switch. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion",
 		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4103/zooz-700-series-switch-zen71-manual.pdf"
 	}
 }

package/config/devices/0x027a/zen76.json

@@ -115,7 +115,7 @@
 	"metadata": {
 		"inclusion": "1. Initiate inclusion (pairing) in the app (or web interface).\n2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion",
 		"exclusion": "1. Bring your Z-Wave gateway (hub) close to the switch if possible\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) \n3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)\n4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4104/zooz-zen76-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse01.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "1. Power the siren up and bring it in within 3 feet from your controller.\n2. Put your Z-Wave controller in inclusion mode.\n3. Press the Z-Wave button on the siren THREE times quickly.\n4. A new alarm device should appear on your controller's dashboard",
 		"exclusion": "1. Bring the siren within 3 feet from your Z-Wave gateway controller.\n\n2. Put your Z-Wave controller in exclusion/unpairing mode.\n\n3. Press and release the Z-Wave button on the siren THREE TIMES quickly.\n\n4. The device should disappear from your controller's device list.\n\nPlease repeat the process following all steps carefully if first attempt is unsuccessful",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the Z-Wave button for 10 seconds. \nNOTE: All previously recorded activity and custom settings will be erased from the siren’s memory",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the Z-Wave button for 10 seconds. \nNOTE: All previously recorded activity and custom settings will be erased from the siren's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1747/zooz-z-wave-indoor-siren-zse01-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse02.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "1. Bring the motion sensor within 3 feet from your controller.\n2. Put your Z-Wave controller in inclusion mode.\n3. Press and release the Z-Wave button on the motion sensor TWICE quickly (to lock and unlock it).\n4. A new motion detection device should appear on your controller's dashboard",
 		"exclusion": "1. Bring the motion sensor within 3 feet from your controller.\n2. Put your Z-Wave controller in exclusion mode.\n3. Press and release the Z-Wave button on the motion sensor TWICE quickly (to lock and unlock it).\n4. The device should disappear from your controller's dashboard.",
-		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, please press the Z-Wave SIX TIMES quickly (3 lock-unlock cycles).\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory.",
+		"reset": "If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, please press the Z-Wave SIX TIMES quickly (3 lock-unlock cycles).\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1743/zooz-z-wave-motion-sensor-zse02-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse11.json

@@ -151,7 +151,7 @@
 	"metadata": {
 		"inclusion": "Put your Z-Wave hub into inclusion mode and click the Z-Wave button 3 times as quickly as possible. The LED indicator will start blinking to confirm inclusion mode and turn off once inclusion is completed. The sensor will automatically pair as a repeater if connected to USB power, no special button sequence required",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave gateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Press and release the Z-Wave button 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then press and hold the Z-Wave button for at least 20 seconds.\nThe LED indicator will start flashing and turn solid on for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then press and hold the Z-Wave button for at least 20 seconds.\nThe LED indicator will start flashing and turn solid on for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4152/zooz-q-sensor-zse11-ver1-manual-online.pdf"
 	}
 }

package/config/devices/0x027a/zse29.json

@@ -137,9 +137,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "AUTO-INCLUSION:\n1. Initiate inclusion (pairing) in the app (or web interface). Not Sure how? ask@getzooz.com. If you’re using an S2 hub, it may ask you to enter the DSK key printed on the back cover sticker to complete secure inclusion.\n2. Insert the batteries or the USB adapter board. The LED indicator\nwill start blinking and the sensor will join the network Automatically.\n\nMANUAL INCLUSION:\nPut your Z-Wave hub into inclusion mode and click the tamper switch 3 times quickly",
+		"inclusion": "AUTO-INCLUSION:\n1. Initiate inclusion (pairing) in the app (or web interface). Not Sure how? ask@getzooz.com. If you're using an S2 hub, it may ask you to enter the DSK key printed on the back cover sticker to complete secure inclusion.\n2. Insert the batteries or the USB adapter board. The LED indicator\nwill start blinking and the sensor will join the network Automatically.\n\nMANUAL INCLUSION:\nPut your Z-Wave hub into inclusion mode and click the tamper switch 3 times quickly",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave\ngateway (hub).\n2. Put the Z-Wave hub into exclusion mode (not sure\nhow to do that? ask@getzooz.com).\n3. Press and release the tamper switch 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will\ndisappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then CLICKCLICK-CLICK-CLICK’N’HOLD the tamper switch for AT LEAST 5 SECONDS. The LED indicator will turn off to\nindicate successful reset. The sensor will then enter auto-inclusion mode for 4 minutes.\nNOTE: All previously recorded activity and custom settings will be erased from the device’s memory.",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then CLICKCLICK-CLICK-CLICK'N'HOLD the tamper switch for AT LEAST 5 SECONDS. The LED indicator will turn off to\nindicate successful reset. The sensor will then enter auto-inclusion mode for 4 minutes.\nNOTE: All previously recorded activity and custom settings will be erased from the device's memory.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3081/zooz-z-wave-plus-s2-outdoor-motion-sensor-zse29-manual.pdf"
 	},
 	"compat": {

package/config/devices/0x027a/zse41.json

@@ -77,7 +77,7 @@
 	"metadata": {
 		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\n\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
 		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4276/zooz-zse41-manual-online.pdf"
 	}

package/config/devices/0x027a/zse42.json

@@ -75,7 +75,7 @@
 	"metadata": {
 		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
 		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4280/zooz-zse42-manual.pdf"
 	}

package/config/devices/0x027a/zse43.json

@@ -171,7 +171,7 @@
 	"metadata": {
 		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
 		"wakeup": "Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash twice to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub.",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-700-series-tilt-shock-xs-sensor-zse43-manual.pdf"
 	}

package/config/devices/0x027a/zse44.json

@@ -404,7 +404,7 @@
 	"metadata": {
 		"inclusion": "Initiate inclusion (pairing) in the app (or web interface). Not sure how? ask@getzooz.com\nWhile the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start flashing to confirm inclusion mode and turn off once inclusion is completed.",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave hub.\n2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).\n3. Click the Z-Wave button 3 times as quickly as possible.\n4. Your hub will confirm exclusion and the sensor will disappear from your controller's device list",
-		"reset": "When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
+		"reset": "When your network's primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately after, click the Z-Wave button twice more to finalize the reset. The LED indicator will flash 3 times to confirm a successful reset",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-700-series-tilt-shock-xs-sensor-zse43-manual.pdf"
 	}
 }

package/config/devices/0x027a/zse70_800lr.json

@@ -303,7 +303,7 @@
 	"metadata": {
 		"inclusion": "Put your Z-Wave® hub into inclusion mode and click\nthe Z-Wave® button 3 times as quickly as possible. The\nLED indicator will start blinking to confirm inclusion\nmode and turn off once inclusion is completed",
 		"exclusion": "1. Bring the sensor within direct range of your Z-Wave®\ngateway (hub).\n2. Put the Z-Wave® hub into exclusion mode (not sure\nhow to do that? ask@getzooz.com).\n3. Click the Z-Wave® button 3 times quickly.\n4. Your hub will confirm exclusion and the sensor will\ndisappear from your controller''s device list",
-		"reset": "When your network’s primary controller is missing or\notherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the\nprocess, make sure the sensor is powered, then hold\nthe Z-Wave® button down for at least 10 seconds.\nThe LED indicator will start flashing blue and turn solid\nblue for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be\nerased from the device’s memory",
+		"reset": "When your network's primary controller is missing or\notherwise inoperable, you may need to reset the device\nto factory settings manually. In order to complete the\nprocess, make sure the sensor is powered, then hold\nthe Z-Wave® button down for at least 10 seconds.\nThe LED indicator will start flashing blue and turn solid\nblue for a couple of seconds to indicate successful reset.\nNOTE: All previously recorded activity and custom settings will be\nerased from the device's memory",
 		"manual": "https://cdn.shopify.com/s/files/1/0218/7704/files/zooz-zse70-800lr-manual.pdf"
 	}
 }

package/config/devices/0x0280/k2.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Note: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\nIn “Other Z-Wave Settings” section on the “smanos home” app, click on “Reset Z-Wave Module” and a pop-up box will be displayed. Click on “Reset” and the Z-Wave module inside the K2 will be restored to factory settings.",
+		"reset": "Note: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\nIn 'Other Z-Wave Settings' section on the 'smanos home' app, click on 'Reset Z-Wave Module' and a pop-up box will be displayed. Click on 'Reset' and the Z-Wave module inside the K2 will be restored to factory settings.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2986/smanos%20k2%20smart%20hub%20user%20manual%20new.pdf"
 	}
 }

package/config/devices/0x0286/eh-ds-01.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into “Add (Inclusion)” mode, and following its instruction to add EH-DS-01 to your controller. This Door/Window sensor needs to be included before installation.\n\n1. Pull the exposed plastic tab from the sensor.\n\n2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.\n\n3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2",
-		"exclusion": "For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into “Remove (Exclusion)” mode, and following its instruction to delete EH-DS-01 to your Z-Wave controller.\n1. Remove device front cover and pressing the button three times within 2 seconds, The Red LED indicator will be flashing three times and enter exclusion mode. \n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove",
+		"inclusion": "For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into 'Add (Inclusion)' mode, and following its instruction to add EH-DS-01 to your controller. This Door/Window sensor needs to be included before installation.\n\n1. Pull the exposed plastic tab from the sensor.\n\n2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.\n\n3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2",
+		"exclusion": "For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into 'Remove (Exclusion)' mode, and following its instruction to delete EH-DS-01 to your Z-Wave controller.\n1. Remove device front cover and pressing the button three times within 2 seconds, The Red LED indicator will be flashing three times and enter exclusion mode. \n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove",
 		"reset": "1. Pressing the button before power on, do not release the button and power on and keep on ten seconds, and the LED will turn ON.\n2. After over 1 seconds the Red LED indicator will turn OFF, then go auto Adding procedure.\n3. IDs are excluded and all settings will reset to factory default.\n4. Device begin auto Adding (Inclusion) mode.\nNote: Use this procedure only in the event that the primary controller is lost",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2317/EH-DS-02manual.pdf"
 	}

package/config/devices/0x0286/zwds01.json

@@ -20,8 +20,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into “Add (Inclusion)” mode, and following its instruction to add ZWDS01-US to your controller. This Door/Window sensor needs to be included before installation.\n\n1. Pull the exposed plastic tab from the sensor.\n\n2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.\n\n3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2",
-		"exclusion": "For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into “Remove (Exclusion)” mode, and following its instruction to delete ZWDS01-EU to your Z-Wave controller.\n1. Remove device front cover and pressing the button three times within 2 seconds, The Red LED indicator will be flashing three times and enter exclusion mode. \n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove",
+		"inclusion": "For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into 'Add (Inclusion)' mode, and following its instruction to add ZWDS01-US to your controller. This Door/Window sensor needs to be included before installation.\n\n1. Pull the exposed plastic tab from the sensor.\n\n2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.\n\n3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2",
+		"exclusion": "For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into 'Remove (Exclusion)' mode, and following its instruction to delete ZWDS01-EU to your Z-Wave controller.\n1. Remove device front cover and pressing the button three times within 2 seconds, The Red LED indicator will be flashing three times and enter exclusion mode. \n2. If remove (exclusion) successful, go auto Adding procedure.\n3. Node ID has been remove",
 		"reset": "1. Pressing the button before power on, do not release the button and power on and keep on ten seconds, and the LED will turn ON.\n2. After over 1 seconds the Red LED indicator will turn OFF, then go auto Adding procedure.\n3. IDs are excluded and all settings will reset to factory default.\n4. Device begin auto Adding (Inclusion) mode.\nNote: Use this procedure only in the event that the primary controller is lost",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2367/ZWDS01%20EU.pdf"
 	}

package/config/devices/0x0299/cdl-107u.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "* Please proceed with the door lock open\n* To add or include the CDL-107U into a Z-Wave network\n1. Set the controller in inclusion mode.\n2. Press the [R] button for 6 seconds.\n3. Press the [1][4][7] button after pressing the [R] button.",
-		"exclusion": "* Please proceed with the door lock open\n* To remove or exclude the CDL-107U into a Z-Wave network\n1. Set the controller in exclusion mode.\n2. Press the [R] button for 6 seconds.\n3. Press the [3][6][9] button after pressing the [R] button.",
-		"reset": "* To Factory Reset\n\nPlease use this procedure only when the primary controller is missing or otherwise inoperable.\n\n1. Press the [R] button for 9 seconds\n\n2. Press the [1][2][3][6][5][4][7] button after pressing the [R] button",
+		"inclusion": "Ensure the door lock is open.\n1. Press the [R] button for 6 seconds.\n2. Press the [R] button, then press [1][4][7].",
+		"exclusion": "Ensure the door lock is open.\n1. Press the [R] button for 6 seconds.\n2. Press the [R] button, then press [3][6][9].",
+		"reset": "1. Press the [R] button for 9 seconds.\n2. Press the [R] button, then press [1][2][3][6][5][4][7].",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3242/CDL-107U%20Manual_Ver1.0_20190214.pdf"
 	}
 }

package/config/devices/0x029f/adsl-1001.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "- Z-Wave inclusion:\n\ni. Press “Z-Wave Settings” button in the inner side for 3 seconds. (toggle status) \n\nii. Then “Blue LED” will turn on.\n\niii. When the inclusion is complete, the led is turned off and the beep sounds. Please wait.\n\n* Beep : Success (Beep), Fail (Beep~)\n* The inclusion results can be found in the controller or in your app",
-		"exclusion": "- Z-Wave exclusion \n\ni. Press “Z-Wave Settings” button in the inner side for 3 seconds. (toggle status)\n\nii. Then “Blue LED” will turn on.\n\niii. When the exclusion is completed, the led is turned off and the beep sounds. Please wait.\n\n* Beep : Success (Beep Beep), Fail (Beep~)\n* The exclusion results can be found in the controller or in your app",
-		"reset": "1. Factory default setting \n\ni. Press “Settings, Input” button in the inner side for 3 seconds.\n\nii. Press “④ - Reset” button in the outer side.\n\niii. Enter “1004” and press the “*” button.\n\n2. Z-Wave device reset locally \n\ni. Press “Z-Wave Settings” button in the inner side 3 times within 1.5 seconds.\n\nii. Then “White LED” will turn on.\n\niii. When the “network reset locally” is complete, the led is turned off. Please wait.\n\n* Beep : Success (Ring), Fail (Beep~)\n* Z-Wave network information is initialized.\n* Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "- Z-Wave inclusion:\n\ni. Press 'Z-Wave Settings' button in the inner side for 3 seconds. (toggle status) \n\nii. Then 'Blue LED' will turn on.\n\niii. When the inclusion is complete, the led is turned off and the beep sounds. Please wait.\n\n* Beep : Success (Beep), Fail (Beep~)\n* The inclusion results can be found in the controller or in your app",
+		"exclusion": "- Z-Wave exclusion \n\ni. Press 'Z-Wave Settings' button in the inner side for 3 seconds. (toggle status)\n\nii. Then 'Blue LED' will turn on.\n\niii. When the exclusion is completed, the led is turned off and the beep sounds. Please wait.\n\n* Beep : Success (Beep Beep), Fail (Beep~)\n* The exclusion results can be found in the controller or in your app",
+		"reset": "1. Factory default setting \n\ni. Press 'Settings, Input' button in the inner side for 3 seconds.\n\nii. Press '④ - Reset' button in the outer side.\n\niii. Enter '1004' and press the '*' button.\n\n2. Z-Wave device reset locally \n\ni. Press 'Z-Wave Settings' button in the inner side 3 times within 1.5 seconds.\n\nii. Then 'White LED' will turn on.\n\niii. When the 'network reset locally' is complete, the led is turned off. Please wait.\n\n* Beep : Success (Ring), Fail (Beep~)\n* Z-Wave network information is initialized.\n* Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2436/User%20and%20Reference%20Guide.pdf"
 	}
 }

package/config/devices/0x0300/7aa-ss-ve-a0.json

@@ -104,7 +104,7 @@
 	"metadata": {
 		"inclusion": "1. Power on your Door Sensor, set your Z-Wave controller into add/inclusion mode.\n2. Trigger this action\n3. LED will flash green during the inclusion, and then solid green for 2 seconds to indicate the inclusion is successful, otherwise the LED will solid red for 2 seconds in which you need to repeat the process form step 2",
 		"exclusion": "1. Power on your Door Sensor, and let the Z-Wave primary controller into remove/exclusion mode.\n2. Trigger this action.\n3. LED will flash red during the exclusion, and then solid red for 2 seconds to indicate that the exclusion is successful, otherwise the LED will solid green for 2 seconds in which you need to repeat the process form step 2.",
-		"reset": "LED will blink red faster and faster within 5 seconds and then keep solid red until the button is released. Device will reset itself to factory default by sending a “Device Reset Locally Notification” to gateway when the button is released.",
+		"reset": "LED will blink red faster and faster within 5 seconds and then keep solid red until the button is released. Device will reset itself to factory default by sending a 'Device Reset Locally Notification' to gateway when the button is released.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4298/zwave700%20DW%20sensor%207AA-SS-VE-A0%20user%20manual-20210910.pdf"
 	}
 }

package/config/devices/0x0300/7ba-kp-v-b-a0.json

@@ -93,9 +93,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Add the Keypad into the Z-Wave network via SmartStart:\n1. Add Keypad DSK into the primary controller SmartStart Provisioning List (If you don’t know how to do this, refer to its manual).\n2. Power on the Keypad again.\n3. The Keypad will send “Z-Wave protocol Command Class” frame to start SmartStart Inclusion.\n4. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2\nNote: Keypad will reset itself to factory default by sending “Device Reset Locally CC” when it is included into a non-security Z-wave network.\nDSK QR code is on the left side of the product with laser printing.\nUser should follow the procedure in the section below if the controller does not support SmartStart inclusion.\n\nAdd the Keypad into the Z-Wave network:\n1. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).\n2. Trigger this action.\n3. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2.",
+		"inclusion": "Add the Keypad into the Z-Wave network via SmartStart:\n1. Add Keypad DSK into the primary controller SmartStart Provisioning List (If you don't know how to do this, refer to its manual).\n2. Power on the Keypad again.\n3. The Keypad will send 'Z-Wave protocol Command Class' frame to start SmartStart Inclusion.\n4. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2\nNote: Keypad will reset itself to factory default by sending 'Device Reset Locally CC' when it is included into a non-security Z-wave network.\nDSK QR code is on the left side of the product with laser printing.\nUser should follow the procedure in the section below if the controller does not support SmartStart inclusion.\n\nAdd the Keypad into the Z-Wave network:\n1. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).\n2. Trigger this action.\n3. Network green LED will flashing at every 1 second to indicate that the inclusion is working, and solid green LED 3 seconds for indicate the inclusion is successful, otherwise the LED will be soild yellow in which you need to repeat the process from step 2.",
 		"exclusion": "Remove the Keypad from a Z-Wave network:\n1. Set the Z-Wave network main controller into removing mode (see Z-Wave controller operating manual).\n2. Trigger this button action. the Network LED will flashing at every 1 second.\n3. If the removing is successful, the LED will solid green for 3 seconds. If the removing is failed then LED display yellow for 3 seconds, otherwise you need to repeat the process from step 2.\nNote: Keypad will start SmartStart Inclusion when it is removed from a Z-wave network.",
-		"reset": "Reset the Keypad to factory default.\n1. Device will reset itself to factory default by sending a “Device Reset Locally Notification” to gateway.\n2. If triggered the factory reset, the network connection led will solid green while factory reset is completed.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"reset": "Reset the Keypad to factory default.\n1. Device will reset itself to factory default by sending a 'Device Reset Locally Notification' to gateway.\n2. If triggered the factory reset, the network connection led will solid green while factory reset is completed.\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4277/keypad%20quick%20guide%207BA-KP-V-B-A0%2020210811(updated).pdf"
 	}
 }

package/config/devices/0x0300/7ca-ss-ve-a0.json

@@ -98,7 +98,7 @@
 	"metadata": {
 		"inclusion": "Add the Motion Sensor into the Z-Wave network:\n5. Power on your Motion Sensor, and let your Z-Wave controller into add/inclusion mode.\n6. 3 consecutive clicks in 1.5 seconds, the Motion Sensor will send out a node info security CC in command class list (Security inclusion), the LED will be fast blink ,the timeout is 20-40 seconds;\n7. If the inclusion is successful, the LED will be turn on within 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above.",
 		"exclusion": "Remove Motion Sensor from a Z-Wave network:\n1. Power on your Motion Sensor, and let the Z-Wave primary controller into remove mode.\n2. 3 consecutive clicks in 1.5 second, the LED will be fast blink ,the timeout is 20-40 seconds;\n3. If Motion Sensor has been successfully removed from your Z-Wave\nnetwork, the LED will be turn on 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above.",
-		"reset": "Reset Motion Sensor to factory default.\n\n1. Triggering this action, in 5 seconds LED will be accelerate blink. After 5 seconds, the LED will remain on until the key is released. Motion Sensor will send “Device_Reset_Locally” to the main controller and exclude from the Z-Wave network when the button is released, this procedure will reset the sensor to factory default.\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n3. When not in the network, triggering this action, in 5 seconds LED will be accelerate blink red. After 5 seconds, the LED will remain on red until the key is released. this procedure will reset the sensor to factory default.",
+		"reset": "Reset Motion Sensor to factory default.\n\n1. Triggering this action, in 5 seconds LED will be accelerate blink. After 5 seconds, the LED will remain on until the key is released. Motion Sensor will send 'Device_Reset_Locally' to the main controller and exclude from the Z-Wave network when the button is released, this procedure will reset the sensor to factory default.\n2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n3. When not in the network, triggering this action, in 5 seconds LED will be accelerate blink red. After 5 seconds, the LED will remain on red until the key is released. this procedure will reset the sensor to factory default.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4297/user%20manual%2003.13%207CA-SS-VE-A0-20210910.pdf"
 	}
 }

package/config/devices/0x030c/fios-g1100-v1.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Bring up Verizon Connected Home mobile application (“CoHo App”). Navigate to the “Z-Wave Troubleshooting” page in one of the following ways: a) Triple bar icon -> Support -> “Z-Wave Troubleshooting”. b) Triple bar icon -> Device Screen -> Axon gateway -> “Z-Wave Troubleshooting Tools”.\nFrom there, press “Reset” button, to reset the Z-Wave network, this will remove all devices from the controller. \nBHR is the primary controller for Z-Wave network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.",
+		"reset": "Bring up Verizon Connected Home mobile application ('CoHo App'). Navigate to the 'Z-Wave Troubleshooting' page in one of the following ways: a) Triple bar icon -> Support -> 'Z-Wave Troubleshooting'. b) Triple bar icon -> Device Screen -> Axon gateway -> 'Z-Wave Troubleshooting Tools'.\nFrom there, press 'Reset' button, to reset the Z-Wave network, this will remove all devices from the controller. \nBHR is the primary controller for Z-Wave network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2826/Coho%20Quick%20Start%20Guide.pdf"
 	}
 }

package/config/devices/0x0312/mp21zp_mp31zp.json

@@ -74,8 +74,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "ADD or Remove the MP21ZP from the existing Z-Wave home control network with your primary controller.\n---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n---When prompted by your primary controller, click the PROG button Three times in one second.\nInclude MP21ZP to/from a Z-Wave Gateway with supporting Security.The MP21ZP can support the Primary Controller that implemented the\nNotice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”. Excluding a node ID allocated by\nZ-WaveTM Controller means “Remove” or “Exclusion”",
-		"exclusion": "ADD or Remove the MP21ZP from the existing Z-Wave home control network with your primary controller.\n---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n---When prompted by your primary controller, click the PROG button Three times in one second.\nInclude MP21ZP to/from a Z-Wave Gateway with supporting Security.The MP21ZP can support the Primary Controller that implemented the\nNotice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”. Excluding a node ID allocated by\nZ-WaveTM Controller means “Remove” or “Exclusion”",
+		"inclusion": "ADD or Remove the MP21ZP from the existing Z-Wave home control network with your primary controller.\n---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n---When prompted by your primary controller, click the PROG button Three times in one second.\nInclude MP21ZP to/from a Z-Wave Gateway with supporting Security.The MP21ZP can support the Primary Controller that implemented the\nNotice: Including a node ID allocated by Z-WaveTM Controller means 'Add' or 'Inclusion'. Excluding a node ID allocated by\nZ-WaveTM Controller means 'Remove' or 'Exclusion'",
+		"exclusion": "ADD or Remove the MP21ZP from the existing Z-Wave home control network with your primary controller.\n---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n---When prompted by your primary controller, click the PROG button Three times in one second.\nInclude MP21ZP to/from a Z-Wave Gateway with supporting Security.The MP21ZP can support the Primary Controller that implemented the\nNotice: Including a node ID allocated by Z-WaveTM Controller means 'Add' or 'Inclusion'. Excluding a node ID allocated by\nZ-WaveTM Controller means 'Remove' or 'Exclusion'",
 		"reset": "Press the button twice quickly and then press and hold the button 10S.device will reset\n(Node:Please use this procedure only when the network primary controller is missing or otherwise inoperable)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4247/MP21ZP-manual-20210722.pdf"
 	}

package/config/devices/0x0312/nzw31t.json

@@ -19,9 +19,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Primary inclusion method is via, \"Auto-Inclusion\". Start the inclusion process on your HUB/Gateway and then flip the circuit back on to bring power to your device. You will have 30 seconds before the device times out. The backup method is toggling UP on the switch 6 times within 2 seconds.",
-		"exclusion": "Toggle UP on the switch 6 times within 2 seconds",
-		"reset": "Please use your controller to remove the device from the network. To factory reset, toggle UP the switch 10x in a row when powered on. However, please only use this method if your controller is missing or inoperable.",
+		"inclusion": "Toggle UP on the switch 6 times within 2 seconds.",
+		"exclusion": "Toggle UP on the switch 6 times within 2 seconds.",
+		"reset": "Toggle UP the switch 10 times in a row when powered on.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2679/NZW31Tmanual171102.pdf"
 	}
 }

package/config/devices/0x0312/zw96.json

@@ -48,7 +48,7 @@
 	"metadata": {
 		"inclusion": "Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\nWhen prompted by your primary controller, press the button 3 times.",
 		"exclusion": "Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\nWhen prompted by your primary controller, press the button 3 times.",
-		"reset": "Power off device, press and hold the button, then power on the device, after 5 seconds the device will reset.\nThis should only be used in the event your network’s primary controller is missing or otherwise inoperable.",
+		"reset": "Power off device, press and hold the button, then power on the device, after 5 seconds the device will reset.\nThis should only be used in the event your network's primary controller is missing or otherwise inoperable.",
 		"manual": "https://www.evalogik.com/uploads/202024315/ZW96-Manual.pdf?rnd=213"
 	}
 }

package/config/devices/0x031e/lzw40.json

@@ -34,8 +34,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "With the power to the smart bulb turned off, start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on power to the bulb and it will blink twice (2x) indicating it’s in inclusion mode. If the bulb was included successfully, it will blink one more (1x) time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there’s still issues, please ensure your bulb is within range",
-		"exclusion": "If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you’re within range and it’s still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on. Your bulb will blink twice (2x), indicating it’s in exclusion mode. When exclusion is successful, it will blink one more time (1x) to confirm. Your HUB should say that the device is excluded",
+		"inclusion": "With the power to the smart bulb turned off, start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on power to the bulb and it will blink twice (2x) indicating it's in inclusion mode. If the bulb was included successfully, it will blink one more (1x) time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there's still issues, please ensure your bulb is within range",
+		"exclusion": "If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you're within range and it's still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on. Your bulb will blink twice (2x), indicating it's in exclusion mode. When exclusion is successful, it will blink one more time (1x) to confirm. Your HUB should say that the device is excluded",
 		"reset": "You may power on/off the bulb 6x (between 0.5-2 seconds each time) or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable. Your bulb will flash twice to confirm factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3657/LZW40%20-%20Manual%20(Compressed).pdf"
 	}

package/config/devices/0x031e/lzw41.json

@@ -70,8 +70,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on and off power to the bulb 3x (ie: Turn On, Turn Off, Turn On, Turn Off, Turn On) and the bulb should flash 3x indicating it’s in inclusion mode. \nIf the bulb was included successfully, it will blink one more time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there’s still issues, please ensure your bulb is within range",
-		"exclusion": "IMPORTANT: If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you’re within range and it’s still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on/off/on/off/on/off/on (3x on and 2x off) until your bulb blinks three (3x) and then blinks 1x to confirm. Your HUB should say that the device is excluded. You may then add (include) the bulb per the instructions below",
+		"inclusion": "Start the inclusion process on your HUB/Gateway.\nOnce the inclusion process has started, turn on and off power to the bulb 3x (ie: Turn On, Turn Off, Turn On, Turn Off, Turn On) and the bulb should flash 3x indicating it's in inclusion mode. \nIf the bulb was included successfully, it will blink one more time. If it was not included successfully, you may have to run an exclusion as mentioned above. If there's still issues, please ensure your bulb is within range",
+		"exclusion": "IMPORTANT: If you are having issues pairing/including your device, please ensure your bulb is within range of your HUB (pages 2-3). If you believe you're within range and it's still not working, then you may have to run an Exclusion. Put your HUB in Exclusion mode and turn the power on/off/on/off/on/off/on (3x on and 2x off) until your bulb blinks three (3x) and then blinks 1x to confirm. Your HUB should say that the device is excluded. You may then add (include) the bulb per the instructions below",
 		"reset": "You may power on/off the bulb 6x (between 0.5-2 seconds each time) or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable. Your bulb will flash twice to confirm factory reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3614/LZW41%20Manual.pdf"
 	}

package/config/devices/0x031e/lzw60.json

@@ -192,7 +192,7 @@
 	],
 	"metadata": {
 		"inclusion": "Press the sensor button 1x and the sensor will flash red rapidly. If successful, the sensor will stop flashing and the red light will be solid for 1-2 seconds, followed by the red light turning off. If unsuccessful, the red light will continue to rapidly flash until it times out after 25 seconds",
-		"exclusion": "Put your HUB in Exclusion mode and press the sensor button 1x. Your sensor will rapidly blink, indicating it’s in exclusion mode. When exclusion is successful, the red light will stop blinking, turn solid red and then turn off",
+		"exclusion": "Put your HUB in Exclusion mode and press the sensor button 1x. Your sensor will rapidly blink, indicating it's in exclusion mode. When exclusion is successful, the red light will stop blinking, turn solid red and then turn off",
 		"reset": "You may hold the Sensor Button for 5 seconds or use a certified controller to remove the device from your network to factory default. The sensors red LED will blink fast and then if successful, will turn off.\n\n \n\nOnly use this procedure in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3723/Inovelli%204-1%20Sensor%20Manual.pdf"
 	}

package/config/devices/0x0320/ho-09zw.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For Inclusion to a network: Put the Z-Wave Interface Controller into “Inclusion” mode, and following its instruction to include HO-09ZB to your controller. This magnetic contact needs to be included before installation.\n1. Pull out the insulating strip, making the device power on. \n2. Pressing the anti-tamper switch three times. \n3. Red LED will blink three times while inclusion the network successful \n4. If inclusion failed, the sensor will go into sleep mode. To wake the sensor again, you need to use magnet or anti-tamper switch to trigger an inclusion process, and then sensor will repeat steps from 3 to 4",
-		"exclusion": "For Exclusion a network: Put the Z-Wave Interface Controller into “Exclusion” mode, and following its instruction to exclude magnetic contact from your Z-Wave controller.\n1. Pressing the anti-tamper switch Triple then enter exclusion mode. \n2. Red LED will blink three times when exclusion of the network is successful.",
+		"inclusion": "For Inclusion to a network: Put the Z-Wave Interface Controller into 'Inclusion' mode, and following its instruction to include HO-09ZB to your controller. This magnetic contact needs to be included before installation.\n1. Pull out the insulating strip, making the device power on. \n2. Pressing the anti-tamper switch three times. \n3. Red LED will blink three times while inclusion the network successful \n4. If inclusion failed, the sensor will go into sleep mode. To wake the sensor again, you need to use magnet or anti-tamper switch to trigger an inclusion process, and then sensor will repeat steps from 3 to 4",
+		"exclusion": "For Exclusion a network: Put the Z-Wave Interface Controller into 'Exclusion' mode, and following its instruction to exclude magnetic contact from your Z-Wave controller.\n1. Pressing the anti-tamper switch Triple then enter exclusion mode. \n2. Red LED will blink three times when exclusion of the network is successful.",
 		"reset": "Press the anti-tamper switch five times to reset.\nNote: Use this procedure only in the event that the primary controller is lost",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2350/HO-09ZWmanual.docx"
 	}

package/config/devices/0x0320/lh-990zw.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Put the Z-Wave Interface Controller into “Inclusion” mode, and following its instruction to include LH-990ZW to your controller. This PIR needs to be included before installation.\n1、 Pull out the insulating strip, making the device power on. \n2、 Pressing the test key three times.\n3、 Red LED will blink three times while the network inclusion successful \n4、 If inclusion failed, the sensor will go into sleep mode. To wake up the sensor again, you need to press the key to trigger an inclusion process, and then repeat steps from 3 to 4.",
-		"exclusion": "Put the Z-Wave interface controller into “Exclusion” mode and following its instruction to exclude PIR from your Z-Wave controller:\n1、 Pressing the test key three times the enter exclusion mode.\n2、 Red LED will blink three times while the network exclusion successful.",
+		"inclusion": "Put the Z-Wave Interface Controller into 'Inclusion' mode, and following its instruction to include LH-990ZW to your controller. This PIR needs to be included before installation.\n1、 Pull out the insulating strip, making the device power on. \n2、 Pressing the test key three times.\n3、 Red LED will blink three times while the network inclusion successful \n4、 If inclusion failed, the sensor will go into sleep mode. To wake up the sensor again, you need to press the key to trigger an inclusion process, and then repeat steps from 3 to 4.",
+		"exclusion": "Put the Z-Wave interface controller into 'Exclusion' mode and following its instruction to exclude PIR from your Z-Wave controller:\n1、 Pressing the test key three times the enter exclusion mode.\n2、 Red LED will blink three times while the network exclusion successful.",
 		"reset": "Press the test key five times while installing battery.\nNote: Use this procedure only in the event that primary controller is lost.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2456/LH-990ZW%20manual.pdf"
 	}

package/config/devices/0x032b/zd2102-5.json

@@ -35,9 +35,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For “Inclusion” (adding to) a network: Put the Z-Wave™ network controller into “inclusion” mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds",
-		"exclusion": "For “Exclusion” (removing from) a network: Put the Z-Wave™ network controller into “exclusion” mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
-		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the “Device Reset Locally Notification” command and reset to the factory default condition. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"inclusion": "For 'Inclusion' (adding to) a network: Put the Z-Wave™ network controller into 'inclusion' mode following its instructions. To add the ZD2102-5 to your controller press the program switch of ZD2102-5 to send the Node Information Frame (NIF). After sending NIF, the network controller will send the auto inclusion request; otherwise, ZD2102-5 will go to sleep after 15 seconds",
+		"exclusion": "For 'Exclusion' (removing from) a network: Put the Z-Wave™ network controller into 'exclusion' mode, following its instructions. To delete the ZD2102-5 from your controller press the program switch of ZD2102-5 for at least 1 second to be excluded. Note: All user and network settings will be cleared and the device reset to factory setting defaults when the device is excluded",
+		"reset": "Factory Default Reset: Trigger the rear cover switch to send the Alarm Report and trigger the reed switch (close & open) 5 times in 10 seconds, ZD2102-5 will send the 'Device Reset Locally Notification' command and reset to the factory default condition. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2249/ZD%202102_10252013.pdf"
 	}
 }

package/config/devices/0x032c/sk-3003-06.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Remove the battery plastic separator or make sure battery level is normally, and Make sure the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller’s operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
-		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller’s operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
+		"inclusion": "1) Remove the battery plastic separator or make sure battery level is normally, and Make sure the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
+		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
 		"reset": "The factory default settings are restored when the device is removed from the network.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2663/Wireless_Door_Sensor_User_Manual_20171117.pdf"
 	}

package/config/devices/0x032c/sk-3003-07.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller’s operating manual).\n3) Click the Add/Remove button on the left side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
-		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller’s operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
+		"inclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the inclusion/Add device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the left side of product triple times in 1.5 seconds.\n4) The product will be detected and included in the Z-Wave network",
+		"exclusion": "1) Make sure battery level is normally and the product is located within direct range of the Z-Wave controller.\n2) Set the main controller into the exclusion/Remove device mode (refer to main controller's operating manual).\n3) Click the Add/Remove button on the bottom side of product triple times in 1.5 seconds.\n4) The product will be detected and excluded from the Z-Wave network",
 		"reset": "The factory default settings are restored when the device is removed from the network or press and hold the Add/Remove button on\nthe left side of product excess 10 seconds.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2711/Wireless_PIR_User_Manual_20171031.pdf"
 	}

package/config/devices/0x032d/bsl01.json

@@ -15,8 +15,8 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Add device mode (see a main controller’s operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while inclusion process implement and light on 2 second after processing complete",
-		"exclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Remove device mode (see a main controller’s operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while exclusion process implement and light on 2 second after processing complete",
+		"inclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Add device mode (see a main controller's operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while inclusion process implement and light on 2 second after processing complete",
+		"exclusion": "1) Ensure the SHDL is powered and the battery is fully charged.\n2) Set the main controller into the Remove device mode (see a main controller's operating manual).\n3) Triple click Z-Wave button on the Z-Wave module(inside lock body) within 1.5 seconds, the LED will flicker rapidly while exclusion process implement and light on 2 second after processing complete",
 		"reset": "Smart Hidden Door Lock restores factory default automatically when the device is excluded.\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2462/BENETEK_SL_EN_V4_Ed_5.pdf"
 	}

package/config/devices/0x0330/homemech-200X.json

@@ -207,7 +207,7 @@
 	],
 	"metadata": {
 		"inclusion": "1. Set primary controller/gateway into inclusion mode.\n2. Power on the push button dimmer and set it into inclusion mode. There are two methods to set the push button dimmer into inclusion mode:\n1)Repower on the dimmer, LED indicator blinks blue quickly, it will be set into inclusion mode automatically, and waiting to be included.\n2)Triple press the button, LED indicator turns off for 2 seconds, within the 2 seconds press and hold the button for over 3 seconds, LED indicator will blink blue quickly, the dimmer will be set into inclusion mode.\nThe LED indicator will stay solid blue to indicate successful inclusion.",
-		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).\n2. Triple press the button, LED indicator turns off for 2 seconds, within the 2 seconds press and hold the button for over 3 seconds, LED indicator will blink blue quickly, the dimmer will be set to exclusion mode, and waiting to be excluded, then the dimmer will be excluded from the network.\nMethod 2: Factory reset the dimmer will force it to be excluded from a network. (please refer to the part “Factory Reset” of this manual)\nNote: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.",
+		"exclusion": "There are two exclusion methods:\nMethod 1: Exclusion from the primary controller/gateway as follows:\n1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).\n2. Triple press the button, LED indicator turns off for 2 seconds, within the 2 seconds press and hold the button for over 3 seconds, LED indicator will blink blue quickly, the dimmer will be set to exclusion mode, and waiting to be excluded, then the dimmer will be excluded from the network.\nMethod 2: Factory reset the dimmer will force it to be excluded from a network. (please refer to the part 'Factory Reset' of this manual)\nNote: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.",
 		"reset": "Short press the button 5 times quickly, LED indicator will turn on cyan for 3 seconds, within the 3 seconds press and hold down the button for over 10 seconds (during the long press process LED indicator will blink cyan quickly), the dimmer will be reset to factory defaults, and detect the load maximum brightness, the load brightness will be restored to 50% and LED indicator will blink cyan slowly.",
 		"manual": "https://drive.usercontent.google.com/download?id=1FKzKvF0CMpwFQNbj80jSLZzegZvNsJqE&export=download&authuser=0"
 	}