@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x001d/vrs15.json

@@ -26,8 +26,8 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "While the Programmer/Controller is in the Inclusion mode and the Locator LED is ON on the switch, press the push pad to turn on the switch. The Programmer/Controller will verify inclusion and the Locator LED will turn OFF.\nIf the switch is flashing Amber while in the Inclusion mode, the Programmer/Controller is still trying to communicate with the switch. Wait until the device stops flashing, then press the push pad.\n\nNOTE: If the Locator LED on the switch turns solid Red while including, there has been a communication error.",
-		"exclusion": "While the Programmer/Controller is in the Exclusion mode and the locator LED is ON on the switch, press the push pad to turn on the switch. The Programmer/Controller will verify Exclusion and the locator LED will turn OFF. If the switch is flashing Amber while in the Exclusion mode, the Programmer/Controller is still trying to communicate with the switch. Wait until the device stops flashing, then press the push pad.",
-		"reset": "On the switch, engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard (refer to figure).\nWait 5 seconds and then press the push pad back into the frame and hold push pad until the locator LED turns Amber and then flashes Red.\nThe switch is now reset.\nOnce the switch is reset, it will be necessary to Re-Include it to a network before it can be used."
+		"inclusion": "Press the push pad to turn on the switch. The Locator LED will turn OFF when inclusion is successful.",
+		"exclusion": "Press the push pad to turn on the switch. The locator LED will turn OFF when exclusion is successful.",
+		"reset": "1. Engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard\n2. Wait 5 seconds and then press the push pad back into the frame and hold until the locator LED turns Amber and then flashes Red"
 	}
 }

package/config/devices/0x001d/zw15s.json

@@ -21,9 +21,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For older controllers, Classic Inclusion is supported.\nDepending on the age of the controller it may need to be 3 to 35 feet from the device when including.\n1. Enter setup mode (see page 10).\n2. Follow the Z-Wave controller instructions to enter inclusion mode.\n3. Tap the top rocker 1 time, the Status LED will quickly flash GREEN.\n4. The Z-Wave controller will confirm successful inclusion to the Z-Wave network",
-		"exclusion": "The Exclusion command found in the Z-Wave controller is used as a best practice for removing devices from a Z-Wave network.\n1. Enter setup mode (see page 10).\n2. Follow the Z-Wave controller instructions to enter exclusion mode.\n3. Tap the top rocker 1 time, the Status LED will quickly flash GREEN.\n4. The Z-Wave controller will confirm successful exclusion from the Z-Wave network",
-		"reset": "When removing a Z-Wave device from the network, it is best practice to use the exclusion process. In situations where a device needs to be returned to factory default settings, follow the steps below. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Hold the top rocker for 14 seconds: After the first 7 seconds, the Status LED will turn AMBER. Continue holding until the Status LED flashes RED/AMBER then release.\n2. The device will reset",
+		"inclusion": "1. Hold the control button for 7 seconds until the LED blinks amber.\n2. Tap the top rocker 1 time\n3. The Status LED will quickly flash green",
+		"exclusion": "1. Hold the control button for 7 seconds until the LED blinks amber.\n2. Tap the top rocker 1 time\n3. The Status LED will quickly flash green",
+		"reset": "Hold the top rocker for 14 seconds. After the first 7 seconds, the Status LED will turn amber, continue holding until the Status LED flashes red/amber then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/997/DI-000-ZW15S-02A-X7.pdf"
 	}
 }

package/config/devices/0x001d/zw4sf.json

@@ -38,9 +38,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Classic Inclusion To A Z-Wave Network\nFor older controllers Classic Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including.\n1. To enter programming mode, hold the button for 7 seconds. The status light will turn amber, release and the status light will blink.\n2. Follow the Z-Wave controller instructions to enter inclusion mode.\n3. Tap the top or the paddle of the paddle one time. The status light will quickly flash green.\n4. The Z-Wave controller will confirm successful inclusion to the network",
-		"exclusion": "Exclusion From A Z-Wave Network\nWhen removing an fan speed controller from a Z-Wave network,\nbest practice is to use the exclusion command found in the Z-Wave\ncontroller.\n1. To enter programming mode, hold the button for 7 seconds. The\nstatus light will turn amber, release and the status light will blink.\n2. Follow Z-Wave controller directions to enter exclusion mode\n3. Tap the the top of the paddle 1 time. The status light will quickly\nflash green.\n4. The Z-Wave controller will remove the device from the network",
-		"reset": "Factory Default\nWhen removing a fan speed controller from a network it is best\npractice to use the exclusion process. In situations where a device\nneeds to be returned to factory default follow the following steps. A\nreset should only be used when a controller is\ninoperable or missing.\n1. Hold the top of the paddle for 7 seconds, the status light will turn amber.\nContinue holding the top paddle for another 7 seconds (total of 14 seconds).\nThe status light will quickly flash red/ amber.\n2. Release the top of the paddle and the device will reset",
+		"inclusion": "1. Hold the button for 7 seconds until the status light turns amber, then release\n2. Tap the top of the paddle one time\n3. The status light will quickly flash green",
+		"exclusion": "1. Hold the button for 7 seconds until the status light turns amber, then release\n2. Tap the top of the paddle one time\n3. The status light will quickly flash green",
+		"reset": "Hold the top of the paddle for 14 seconds. The status light will quickly flash red/amber.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3832/Draft%20ZW4SF%203-25-20.pdf"
 	}
 }

package/config/devices/0x001d/zw6hd.json

@@ -53,9 +53,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "For older controllers, Classic Inclusion is supported.\nDepending on the age of the controller it may need to be 3 to 35 feet from the device when including.\n1. Enter setup mode (see page 10).\n2. Follow the Z-Wave controller instructions to enter\ninclusion mode.\n3. Tap the top rocker 1 time, the Status LED will quickly\nflash GREEN.\n4. The Z-Wave controller will confirm successful inclusion to the Z-Wave network",
-		"exclusion": "The Exclusion command found in the Z-Wave controller is used as a best practice for removing devices from a\nZ-Wave network.\n1. Enter setup mode (see page 10).\n2. Follow the Z-Wave controller instructions to enter\nexclusion mode.\n3. Tap the top rocker 1 time, the Status LED will quickly\nflash GREEN.\n4. The Z-Wave controller will confirm successful exclusion from the Z-Wave network",
-		"reset": "When removing a Z-Wave device from the network, it is best practice to use the exclusion process. In situations where a device needs to be returned to factory default settings, follow the steps below. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n1. Hold the top rocker for 14 seconds: After the first 7 seconds, the Status LED will turn AMBER. Continue holding until the Status LED flashes RED/AMBER then release.\n2. The device will reset",
+		"inclusion": "1. Hold the control button for 7 seconds until the LED blinks amber\n2. Tap the top rocker 1 time\n3. The Status LED will quickly flash green",
+		"exclusion": "1. Hold the control button for 7 seconds until the LED blinks amber\n2. Tap the top rocker 1 time\n3. The Status LED will quickly flash green",
+		"reset": "Hold the top rocker for 14 seconds. After the first 7 seconds, the Status LED will turn amber, continue holding until the Status LED flashes red/amber then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=cert_portal/certs/633/DI-000-ZW6HD-02A-X4.pdf"
 	}
 }

package/config/devices/0x001e/ezzee.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Please do this only after removing all nodes from the network.\nFrom the Z-Wave Plug-In menu, choose \"Controller Management\". Under the options for the interface that is using the Z-Net controller, choose \"ERASE this Interface and Create A New Network\", and follow the system prompts",
+		"reset": "1. From the Z-Wave Plug-In menu, choose \"Controller Management\"\n2. Under the interface options, choose \"ERASE this Interface and Create A New Network\"\n3. Follow the system prompts",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1252/Z-Net-Installation-Guide.pdf"
 	}
 }

package/config/devices/0x002c/z-flexnet_dongl.json

@@ -161,9 +161,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter your Z-Wave Controller into Inclusion/Add Mode.\n2. Press the Lighting Panel \"Scene1\" button more than 3 times within 1 second.\nOR, to use NWI:\n1. Enter your Z-Wave Controller into Inclusion/Add Mode.\n2. Power on the FlexNET Dongle. It will be active during 4 seconds",
-		"exclusion": "1. Enter your Z-Wave Controller into Exclusion/Remove Mode.\n2. Press the Lighting Panel \"Scene1\" button more than 3 times within 1 second",
-		"reset": "To Reset to Factory Default send the following parameter:\nParameter: 15\nBytes: 01\nValue: 255\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Lighting Panel \"Scene1\" button more than 3 times within 1 second.",
+		"exclusion": "Press the Lighting Panel \"Scene1\" button more than 3 times within 1 second.",
+		"reset": "Set parameter 15 to value 255.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2804/FlexNET%20Dongle_Device%20Manual_v5.pdf"
 	}
 }

package/config/devices/0x0039/39336_39443_zw3104.json

@@ -148,9 +148,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add\nthe smart dimmer to the Z-Wave network.\n2. Once the controller is ready to add your smart dimmer, single\npress and release the manual/program button on the smart\ndimmer to add it in the network.\nPlease reference the controller/gateway’s manual for instructions",
+		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add\nthe smart dimmer to the Z-Wave network.\n2. Once the controller is ready to add your smart dimmer, single\npress and release the manual/program button on the smart\ndimmer to add it in the network.\nPlease reference the controller/gateway's manual for instructions",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button on the smart dimmer to\nremove it from the network",
-		"reset": "To return your dimmer to factory defaults:\n1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your networks’ primary\ncontroller is missing or otherwise inoperable",
+		"reset": "To return your dimmer to factory defaults:\n1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your networks' primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3743/39443-HQSG_v3.pdf"
 	}
 }

package/config/devices/0x0039/39337_39444_zw4103.json

@@ -40,7 +40,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include the device to the Z-Wave network. \n2. Once the controller is ready to include your smart switch, single press and release the manual/program button on the smart dimmer to include it in the network.\n3. Once your controller has confirmed that the smart switch has been included, refresh the Z-Wave network to optimize performance.",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network. \n2. Once the controller is ready to exclude your device, press and release the manual/program button on the smart switch to exclude it from the network.",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your network’s\nprimary controller is missing or otherwise inoperable",
+		"reset": "1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2686/39337-HQSG_v1.pdf"
 	}
 }

package/config/devices/0x0039/39339_39346_zw3107.json

@@ -134,9 +134,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add\nthe smart dimmer to the Z-Wave network.\n2. Once the controller is ready to add your smart dimmer, single\npress and release the manual/program button on the smart\ndimmer to add it in the network.\nPlease reference the controller/gateway’s manual for instructions",
+		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add\nthe smart dimmer to the Z-Wave network.\n2. Once the controller is ready to add your smart dimmer, single\npress and release the manual/program button on the smart\ndimmer to add it in the network.\nPlease reference the controller/gateway's manual for instructions",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button on the smart dimmer to\nremove it from the network",
-		"reset": "To return your dimmer to factory defaults:\n1. If plugged in, unplug the dimmer from the receptacle.\n2. Press and hold the top button for at least 3 seconds while you\nplug the dimmer into a receptacle.\nNote: This should only be used in the event your networks’ primary\ncontroller is missing or otherwise inoperable",
+		"reset": "To return your dimmer to factory defaults:\n1. If plugged in, unplug the dimmer from the receptacle.\n2. Press and hold the top button for at least 3 seconds while you\nplug the dimmer into a receptacle.\nNote: This should only be used in the event your networks' primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3830/39446-HQSG_v4.pdf"
 	}
 }

package/config/devices/0x0039/39342_39449_zw4106.json

@@ -60,7 +60,7 @@
 	"metadata": {
 		"inclusion": "Adding your device to a Z-Wave network:\n1. Follow the instructions for your Z-Wave certified controller to\ninclude the device to the Z-Wave network.\n2. Once the controller is ready to include your smart switch,\nsingle press and release the manual/program button on the\nsmart switch to include it in the network.\nNow you have complete control to turn your lamp ON/OFF\naccording to groups, scenes, schedules and interactive\nautomations programmed by your controller.\nIf your Z-Wave certified controller features Remote Access,\nyou can now control your lighting from your mobile devices",
 		"exclusion": "To exclude and reset the device:\n1. Follow the instructions for your Z-Wave certified controller to\nexclude a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, press\nand release the manual/program button on the smart switch\nto exclude it from the network",
-		"reset": "To return your switch to factory defaults:\n1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your networks’\nprimary controller is missing or otherwise inoperable",
+		"reset": "To return your switch to factory defaults:\n1. If plugged in, unplug the device from the receptacle.\n2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.\nNote: This should only be used in the event your networks'\nprimary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3740/39449-HQSG_v3.pdf"
 	}
 }

package/config/devices/0x0039/39348_39455_zw4008.json

@@ -82,7 +82,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart switch (rocker) to add it in the network.\n\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart switch (rocker) to remove it from the network",
-		"reset": "Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3599/39348%20Binder.pdf"
 	}
 }

package/config/devices/0x0039/39349_39456_zw1002.json

@@ -41,7 +41,7 @@
 	"metadata": {
 		"inclusion": "Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the Program Button to add it in the network",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button to remove it from the\nnetwork",
-		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network’s primary\ncontroller is missing or otherwise inoperable",
+		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network's primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2690/39349_HQSG_1.pdf"
 	}
 }

package/config/devices/0x0039/39351_39458_zw3005.json

@@ -56,7 +56,7 @@
 		{
 			"#": "4",
 			"label": "Invert Switch",
-			"description": "If the switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”",
+			"description": "If the switch is accidentally installed upside down with 'On' at the bottom and 'Off' at the top, the default On/Off rocker settings can be reversed by changing parameter 4's value to '1'",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,
@@ -134,9 +134,9 @@
 		"mapBasicSet": "event"
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to\ninclude a device to the Z-Wave network.\n2. Once the controller is ready to add your device,\npress and release the top or bottom of the wireless smart\nswitch (rocker) to add it in the network.\nPlease reference the controller’s manual for instructions",
+		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to\ninclude a device to the Z-Wave network.\n2. Once the controller is ready to add your device,\npress and release the top or bottom of the wireless smart\nswitch (rocker) to add it in the network.\nPlease reference the controller's manual for instructions",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to Exclude your device, press\nand release the top or bottom of the wireless smart dimmer\n(rocker) to remove it from the network",
-		"reset": "Quickly press ON (Top) button three (3) times then immediately\npress the OFF (Bottom) button three (3) times. The LED will flash\nON/OFF 5 times when completed successfully.\nNOTE: This should only be used in the event your network’s\nprimary controller is missing or otherwise inoperable",
+		"reset": "Quickly press ON (Top) button three (3) times then immediately\npress the OFF (Bottom) button three (3) times. The LED will flash\nON/OFF 5 times when completed successfully.\nNOTE: This should only be used in the event your network's\nprimary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3751/39458_HQSG_v3.pdf"
 	}
 }

package/config/devices/0x0039/39351_39458_zw3010.json

@@ -148,7 +148,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and release the top or bottom of the wireless smart dimmer (rocker) to add it in the network.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart dimmer (rocker) to remove it from the network",
-		"reset": "Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash 5 times when completed successfully.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3600/39351%20Binder.pdf"
 	}
 }

package/config/devices/0x0039/39354_39461_zw4003.json

@@ -91,7 +91,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up on the toggle.\n\nA. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product.\n\nNow you have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up on the toggle",
-		"reset": "Quickly press UP button 3 times, then, immediately press the DOWN button 3 times.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "Quickly press UP button 3 times, then, immediately press the DOWN button 3 times.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3400/39354-2.pdf"
 	}
 }

package/config/devices/0x0039/39354_39461_zw4009.json

@@ -91,7 +91,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up on the toggle.\n\nA. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product.\n\nNow you have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up on the toggle",
-		"reset": "Quickly press UP button 3 times, then, immediately press the DOWN button 3 times.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "Quickly press UP button 3 times, then, immediately press the DOWN button 3 times.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3400/39354-2.pdf"
 	}
 }

package/config/devices/0x0039/39357_39464_zw3011.json

@@ -131,7 +131,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press up and release the toggle.\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press up and release the toggle",
-		"reset": "Quickly press UP button three times, then, immediately press the DOWN button three times.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "Quickly press UP button three times, then, immediately press the DOWN button three times.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3601/39357%20Binder.pdf"
 	}
 }

package/config/devices/0x0039/39358_39465_zw4002.json

@@ -55,7 +55,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, press and release the top or bottom of the smart fan control switch (rocker) to include it in the network.\n3. Once your controller has confirmed the device has been included, refresh the Z-Wave network to optimize performance",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network. \n2. Once the controller is ready to Exclude your device, press and release the top or bottom of the wireless smart switch (rocker) to exclude it from the network",
-		"reset": "1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2725/39358-HQSG-v1-para.pdf"
 	}
 }

package/config/devices/0x0039/39363_39470_zw4203.json

@@ -77,7 +77,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network. \n\n2. Once the controller is ready to add your device, press and the manual/program button on the smart switch.\n\nIf prompted by the controller to enter the S2 security code, refer to the QR code/security number on the box or the QR code label on the product. Enter the 5-digit code",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.\n\n2. Once the controller is ready to remove your device, press the manual/program button on the smart switch to remove it from the network",
-		"reset": "1. If plugged in, unplug the device from the receptacle.\n\n2. Press and hold the manual/program button, plug the device in, and continue to hold for at least 3 seconds.\n\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "1. If plugged in, unplug the device from the receptacle.\n\n2. Press and hold the manual/program button, plug the device in, and continue to hold for at least 3 seconds.\n\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3476/39363-QSG-1.pdf"
 	}
 }

package/config/devices/0x003b/be468zp.json

@@ -98,9 +98,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "One-button Add lock to Z-Wave Network (Inclusion) \n\n1. Place your home automation system or panel into the “Add” or Inclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). \n2. Remove the battery cover of the deadbolt. \n3. Press then release the button on the PCB.\n4. An LED will flash amber indicating the “Add” or Inclusion process is in progress. \n• If the Security Scheme is Security 2 (S2), verify the DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed.\n5. When a green LED turns ON, the “Add” or Inclusion has completed successfully. \n6. If a red LED turns ON, try repeating steps 1-3 \n \nInteractive Instruction for Add \nhttps://instructions.allegion.com/instr/86/2543",
-		"exclusion": "One-button Remove lock from Z-Wave Network (Exclusion) \n\n1. Place your home automation system or panel into the “Remove” or Exclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). \n2. Remove the battery cover of the deadbolt. \n3. Press then release the button on the PCB. \n4. An LED will flash amber indicating the “Remove” or Exclusion process is in progress. \n5. When a green LED flashes 3 times, the “Remove” or Exclusion process is completed successfully. \n6. If a red LED turns ON, try repeating steps 1-3 \n\nInteractive Instruction for Remove https://instructions.allegion.com/instr/86/2581",
-		"reset": "Steps for One-button Factory Default Reset \n\n1. Remove the battery cover of the deadbolt\n2. Press and hold the button on the PCB for 7 (seven) seconds. \nWhile holding the button pressed, after 1 sec LED will be lit for 2 sec. and turn OFF; continue to press and hold the button until the LED will be lit again and release the button.\n3. The LED will blink red three times and the green check on the touchscreen will blink if the Factory Default Reset is successful. \n4. To check that the lock was reset, press the Schlage Button and enter one of the Default User Codes. If the reset was successful, the Default User Codes will unlock the deadbolt. \nNOTE: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED indicates successful inclusion, red LED indicates failure",
+		"exclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED flashes 3 times when exclusion is successful",
+		"reset": "1. Remove the battery cover of the deadbolt\n2. Press and hold the button on the PCB for 7 seconds until LED lights again, then release\n3. Red LED blinks three times and green check on touchscreen blinks when reset is successful",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3707/Connect_QSG_Add_Remove_FDR_Association.pdf"
 	}
 }

package/config/devices/0x003b/jbe109.json

@@ -107,9 +107,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "One-button Add lock to Z-Wave Network (Inclusion) 1. Place your home automation system or panel into the “Add” or Inclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). 2. Remove the battery cover of the deadbolt. 3. Press then release the button on the PCB. 4. An LED will flash amber indicating the “Add” or Inclusion process is in progress. • If the Security Scheme is Security 2 (S2), verify the DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed. 5. When a green LED turns ON, the “Add” or Inclusion has completed successfully. 6. If a red LED turns ON, try repeating steps 1-3 Interactive Instruction for Add https://instructions.allegion.com/instr/86/2543",
-		"exclusion": "One-button Remove lock from Z-Wave Network (Exclusion) 1. Place your home automation system or panel into the “Remove” or Exclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). 2. Remove the battery cover of the deadbolt. 3. Press then release the button on the PCB. 4. An LED will flash amber indicating the “Remove” or Exclusion process is in progress. 5. When a green LED flashes 3 times, the “Remove” or Exclusion process is completed successfully. 6. If a red LED turns ON, try repeating steps 1-3 Interactive Instruction for Remove https://instructions.allegion.com/instr/86/258",
-		"reset": "1. Press and hold the enrollment button. The led will light solid amber. 2. After about 8 seconds of holding the button, the amber light will turn off. Release the button. Successful FDR is indicated by 3 long green blinks and 3 long beeps. 3. You must enter a valid user code. Lock will enter auto-handing routine, locking and unlocking several times. Auto-handing is complete when lock movement stops",
+		"inclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED indicates successful inclusion, red LED indicates failure",
+		"exclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED flashes 3 times when exclusion is successful",
+		"reset": "1. Press and hold the enrollment button until LED lights amber\n2. Continue holding for about 8 seconds until amber light turns off, then release\n3. Success is indicated by 3 long green blinks and 3 long beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4134/J-Series%20UG-f1.pdf"
 	}
 }

package/config/devices/0x003b/jfe109.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "One-button Add lock to Z-Wave Network (Inclusion) 1. Place your home automation system or panel into the “Add” or Inclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). 2. Remove the battery cover of the deadbolt. 3. Press then release the button on the PCB. 4. An LED will flash amber indicating the “Add” or Inclusion process is in progress. • If the Security Scheme is Security 2 (S2), verify the DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed. 5. When a green LED turns ON, the “Add” or Inclusion has completed successfully. 6. If a red LED turns ON, try repeating steps 1-3 Interactive Instruction for Add https://instructions.allegion.com/instr/86/2543",
-		"exclusion": "One-button Remove lock from Z-Wave Network (Exclusion) 1. Place your home automation system or panel into the “Remove” or Exclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details). 2. Remove the battery cover of the deadbolt. 3. Press then release the button on the PCB. 4. An LED will flash amber indicating the “Remove” or Exclusion process is in progress. 5. When a green LED flashes 3 times, the “Remove” or Exclusion process is completed successfully. 6. If a red LED turns ON, try repeating steps 1-3 Interactive Instruction for Remove https://instructions.allegion.com/instr/86/2581",
-		"reset": "1. Press and hold the enrollment button. The led will light solid amber. 2. After about 8 seconds of holding the button, the amber light will turn off. Release the button. Successful FDR is indicated by 3 long green blinks and 3 long beeps. 3. You must enter a valid user code. Lock will enter auto-handing routine, locking and unlocking several times. Auto-handing is complete when lock movement stops",
+		"inclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED indicates successful inclusion, red LED indicates failure",
+		"exclusion": "1. Remove the battery cover of the deadbolt\n2. Press then release the button on the PCB\n3. Green LED flashes 3 times when exclusion is successful",
+		"reset": "1. Press and hold the enrollment button until LED lights amber\n2. Continue holding for about 8 seconds until amber light turns off, then release\n3. Success is indicated by 3 long green blinks and 3 long beeps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4136/J-Series%20UG-e.pdf"
 	}
 }

package/config/devices/0x003b/s-6500f.json

@@ -72,9 +72,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place your Z-Wave Controller into the “Add” or Inclusion Mode (Refer the respective documentation for that specific home automation system or panel device for details).\n2. Slide the battery cover upward.\n3. Press the wireless button more than 3 seconds.\n4. Press “1” on the keypad.\n5. Press “6” on the keypad.\n6. Press User Code on the keypad.\n7. Press “#” on the keypad.\n8. If RF LED flickers, inclusion has completed successfully.\n9. If battery replace LED flickers(fail), try repeating steps 1-7",
-		"exclusion": "1. Place your Z-Wave Controller into the “Remove” or Exclusion Mode (Refer the respective documentation for that specific home automation system or panel device for details).\n2. Slide the battery cover upward.\n3. Press the wireless button more than 3 seconds.\n4. Press “2” on the keypad.\n5. Press “6” on the keypad.\n6. Press User Code on the keypad.\n7. Press “#” on the keypad.\n8. If RF LED flickers, exclusion has completed successfully.\n9. If battery replace LED flickers, try repeating steps 1-7",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable.\nWhen Master code was already registered\n1. Remove batteries (power off).\n2. Press “N” and “S” buttons at the same time and hold.\n3. Insert batteries (power on).\n4. Release “N” and “S” buttons.\n5. Press 3-digit Master code.\n6. Press “#” on the keypad.\n7. Press “8” on the keypad.\nWhen Master code was not registered yet\n1. Remove batteries (power off).\n2. Press “N” button and “S” button at the same time and hold.\n3. Insert batteries (power on).\n4. Release “N” and “S” buttons.\n5. Press 3-digit Master code to register.\n6. Press “#” on the keypad.\n7. Press previous 3-digit Master code.\n8. Press “#” on the keypad",
+		"inclusion": "1. Slide the battery cover upward\n2. Press the wireless button for more than 3 seconds\n3. Enter sequence: 1, 6, [User Code], #\n4. RF LED flickers when successful",
+		"exclusion": "1. Slide the battery cover upward\n2. Press the wireless button for more than 3 seconds\n3. Enter sequence: 2, 6, [User Code], #\n4. RF LED flickers when successful",
+		"reset": "When Master code is already registered:\n1. Remove batteries\n2. Press and hold \"N\" and \"S\" buttons simultaneously\n3. Insert batteries while holding buttons\n4. Release buttons\n5. Enter Master code, then #\n6. Press 8\n\nWhen Master code is not registered:\n1. Remove batteries\n2. Press and hold \"N\" and \"S\" buttons simultaneously\n3. Insert batteries while holding buttons\n4. Release buttons\n5. Enter Master code to register, then #\n6. Enter the same Master code again, then #",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4122/Manual%20for%20Schlage%20Z-Wave%20Mortise%20Lock%20v1.1.pdf"
 	}
 }

package/config/devices/0x0047/sy-iot101.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the SY-IOT101to your controller. To get in the “inclusion” mode.\n - Check if SY-IOT101 module is in exclusion mode.\n- Press the program switch for above 5 second, then, the LED is turned on.\n- Release from the program switch.\n- Then, SY-IOT101 module will try inclusion.\n- If inclusion is succeeded, LED is blinked 3 times.\n- If inclusion is failed, LED is turn off.",
-		"exclusion": "For “Exclusion” removing from the network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to add the SY-IOT101 to your controller. To get in the “exclusion” mode.\n - Check if SY-IOT101 module is in inclusion mode\n- Press the program switch for above 5 second, then the LED is turned on.\n- Release from the program switch. \n- Then, SY-IOT101 module will try inclusion.\n- If inclusion is succeeded, LED is blinked 3 times.\n- If exclusion is failed, LED is turn off.",
-		"reset": "Local Reset (Factory Default Reset )\n- Press the program switch for above 10 second, then the LED is blinked until program switch is released.\n- Release from the program switch.\n- Then, SY-IOT101 module will try local reset.\n- If local reset is succeeded, LED is blinked 5 times.\n- After blinking LED, SY-IOT101 will send the “Device Reset Locally Notification” command and reset to the factory default. \n- If local reset is failed, LED is turn off.\n* Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "For 'Inclusion' in (adding to) a network: Put the Z-Wave™ Interface Controller into 'inclusion' mode, and following its instruction to add the SY-IOT101to your controller. To get in the 'inclusion' mode.\n - Check if SY-IOT101 module is in exclusion mode.\n- Press the program switch for above 5 second, then, the LED is turned on.\n- Release from the program switch.\n- Then, SY-IOT101 module will try inclusion.\n- If inclusion is succeeded, LED is blinked 3 times.\n- If inclusion is failed, LED is turn off.",
+		"exclusion": "For 'Exclusion' removing from the network: Put the Z-Wave™ Interface Controller into 'exclusion' mode, and following its instruction to add the SY-IOT101 to your controller. To get in the 'exclusion' mode.\n - Check if SY-IOT101 module is in inclusion mode\n- Press the program switch for above 5 second, then the LED is turned on.\n- Release from the program switch. \n- Then, SY-IOT101 module will try inclusion.\n- If inclusion is succeeded, LED is blinked 3 times.\n- If exclusion is failed, LED is turn off.",
+		"reset": "Local Reset (Factory Default Reset )\n- Press the program switch for above 10 second, then the LED is blinked until program switch is released.\n- Release from the program switch.\n- Then, SY-IOT101 module will try local reset.\n- If local reset is succeeded, LED is blinked 5 times.\n- After blinking LED, SY-IOT101 will send the 'Device Reset Locally Notification' command and reset to the factory default. \n- If local reset is failed, LED is turn off.\n* Please use this procedure only when the network primary controller is missing or otherwise inoperable.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2472/User_Manual_z-wave%20curtain%20motor%20module_0712R.pdf"
 	}
 }

package/config/devices/0x004f/fx-d67.json

@@ -28,9 +28,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. have your Z-Wave controller enter into Inclusion mode\n2. press the dimmer socket button three times within 1.5 seconds",
-		"exclusion": "1. have your Z-Wave controller enter into Exclusion mode\n2. press the dimmer socket button three times within 1.5 seconds",
-		"reset": "1. Press your dimmer socket button four times within 1.5 seconds\n2. the fourth time press and hold on the socket button for 5 seconds until socket LED button off \n3. Use the \"RESET\" procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the dimmer socket button three times within 1.5 seconds.",
+		"exclusion": "Press the dimmer socket button three times within 1.5 seconds.",
+		"reset": "Press the dimmer socket button four times within 1.5 seconds. On the fourth press, hold the socket button for 5 seconds until socket LED turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2427/FX67.pdf"
 	}
 }

package/config/devices/0x004f/fx-s69.json

@@ -60,9 +60,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Enter your Z-Wave controller into inclusion mode\n2. Press the socket on/off button three times within 1.5 seconds to be included",
-		"exclusion": "1. Enter your Z-Wave controller into exclusion mode\n2. Press the socket on/off button three times within 1.5 seconds to be excluded",
-		"reset": "1. To reset, press the socket on/off button three times within 1.5 seconds\n2. then the fourth time, press and hold for seconds until the socket LED is off\n3. the socket reset successfully\n\nUse the \"Reset\" procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the socket on/off button three times within 1.5 seconds.",
+		"exclusion": "Press the socket on/off button three times within 1.5 seconds.",
+		"reset": "Press the socket on/off button four times within 1.5 seconds. On the fourth press, hold for 5 seconds until the socket LED turns off.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2428/FX69.pdf"
 	}
 }

package/config/devices/0x004f/fxs-m08.json

@@ -56,7 +56,7 @@
 		{
 			"#": "5",
 			"label": "External Switch Type",
-			"description": "1. one push button:  when the configuration setting is one push button, only s1 input will be valid. the control moving commands can be accepted in this switch type while the shutter is moving. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 just like the operation of include button. when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving s1 is short pressed again, the shutter will stop moving. a third short pressing of s1 will move the shutter down toward bottom(0x00). while in this moving s1 is short pressed again, the shutter will stop moving. and so on… inverting direction and stopping.   2. two push button： (the default setting is two push button (2))  if this setting is configured as two push button, s1 and s2 input will be valid, but will not accept pressing s1and s2 at the same time. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 or s2 just like the operation of include button.  when s1 is pressed and hold more than 1.5 seconds, the shutter will move up toward top(0x63), and the shutter will stop moving when s1 is released. when s2 is pressed and hold more than 1.5 seconds, the shutter will move down toward bottom(0x00), and the shutter will stop moving when s2 is released.   when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving short pressed s1 again, the shutter just keep moving up toward top(0x63). the easy way to stop this moving is short pressing s2. when s2 is short pressed, the shutter will move down toward button(0x00). while in this moving short pressed s2 again, the shutter just keep moving down toward button(0x00). the easy way to stop this moving is short pressing s1.    when in two push button switch type, s1 or s2 are pressed and not released, and fxs-m08 receive any control moving command from Z-Wave rf (ex. basic_set、binary_switch_set、multilevel_switch_set、multilevel_switch_start_level_change or multilevel_switch_stop_level_change or scene_activation_set), fxs-m08 won’t do any change in position but report alarm to group1 (alarm_type=1, alarm_level =0xff), this indicate that the s1 or s2 not been release.  att. : for avoid misunderstanding that rf command dose not work, it is recommended to check the status of s1 and s2",
+			"description": "1. one push button:  when the configuration setting is one push button, only s1 input will be valid. the control moving commands can be accepted in this switch type while the shutter is moving. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 just like the operation of include button. when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving s1 is short pressed again, the shutter will stop moving. a third short pressing of s1 will move the shutter down toward bottom(0x00). while in this moving s1 is short pressed again, the shutter will stop moving. and so on… inverting direction and stopping.   2. two push button： (the default setting is two push button (2))  if this setting is configured as two push button, s1 and s2 input will be valid, but will not accept pressing s1and s2 at the same time. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 or s2 just like the operation of include button.  when s1 is pressed and hold more than 1.5 seconds, the shutter will move up toward top(0x63), and the shutter will stop moving when s1 is released. when s2 is pressed and hold more than 1.5 seconds, the shutter will move down toward bottom(0x00), and the shutter will stop moving when s2 is released.   when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving short pressed s1 again, the shutter just keep moving up toward top(0x63). the easy way to stop this moving is short pressing s2. when s2 is short pressed, the shutter will move down toward button(0x00). while in this moving short pressed s2 again, the shutter just keep moving down toward button(0x00). the easy way to stop this moving is short pressing s1.    when in two push button switch type, s1 or s2 are pressed and not released, and fxs-m08 receive any control moving command from Z-Wave rf (ex. basic_set、binary_switch_set、multilevel_switch_set、multilevel_switch_start_level_change or multilevel_switch_stop_level_change or scene_activation_set), fxs-m08 won't do any change in position but report alarm to group1 (alarm_type=1, alarm_level =0xff), this indicate that the s1 or s2 not been release.  att. : for avoid misunderstanding that rf command dose not work, it is recommended to check the status of s1 and s2",
 			"valueSize": 1,
 			"unit": "seconds",
 			"defaultValue": 2,
@@ -93,9 +93,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing Include button three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing Include button three times within 2 seconds will enter exclusion mode",
-		"reset": "Use this procedure only in the event that the primary controller is lost or otherwise inoperable. \n1. Pressing Include button three times within 2 seconds will enter inclusion mode. \n2. Within 1 second, press Include button again for 5 seconds.",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "Press the Include button three times within 2 seconds to enter inclusion mode. Within 1 second, press the Include button again for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2598/FXS-M08%20User%20Manual_ZWPlus_v4.pdf"
 	}
 }

package/config/devices/0x0059/bbk001-z00.json

@@ -81,9 +81,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "On thermostat in advance mode scroll to option “Add device”, then click OK button. On other Z-Wave device start learn process, thermostat will display outcome on completion of the process.",
-		"exclusion": "On thermostat in advance mode scroll to option “Remove device”, then click OK button. On other Z-Wave device start learn process, thermostat will display outcome on completion of the process.",
-		"reset": "On thermostat in advance mode scroll to option “Factory Reset”, then click OK button.\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "On thermostat in advance mode scroll to option 'Add device', then click OK button. On other Z-Wave device start learn process, thermostat will display outcome on completion of the process.",
+		"exclusion": "On thermostat in advance mode scroll to option 'Remove device', then click OK button. On other Z-Wave device start learn process, thermostat will display outcome on completion of the process.",
+		"reset": "On thermostat in advance mode scroll to option 'Factory Reset', then click OK button.\n\nNote: Please use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2396/Thermostat%20Manual%20V3.pdf"
 	}
 }

package/config/devices/0x0059/max10y-376.json

@@ -119,9 +119,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "STEP 1: Ensure the RF LED is flashing on the SIR 321, if not than follow ‘Exclusion’ steps first.\nSTEP 2: Put the third party controller into inclusion mode.\nSTEP 3: Press and hold the pairing button on the SIR 321 until the RF LED start flashing at a fast rate. Then release the button.\nThe SIR 321 has been added onto the network when the RF LED stop flashing",
-		"exclusion": "STEP 1: Put the third party controller into exclusion mode.\nSTEP 2: Press and hold the pairing button on the SIR 321 until the RF LED start flashing at a fast rate. Then release the button.\nThe SIR 321 has been removed from the network when the RF LED starts flashing",
-		"reset": "\"Please use this procedure only when the primary controller is missing or otherwise inoperable.\"\n\nPress pairing button and boost button simultaneously until RF LED starts flashing to put the device in a factory default mode, all the configuration and association set to factory default and removing the device from Z-wave network",
+		"inclusion": "1. Ensure the RF LED is flashing on the SIR 321, if not then follow exclusion steps first.\n2. Press and hold the pairing button on the SIR 321 until the RF LED starts flashing at a fast rate, then release the button.\n3. The SIR 321 has been added when the RF LED stops flashing.",
+		"exclusion": "1. Press and hold the pairing button on the SIR 321 until the RF LED starts flashing at a fast rate, then release the button.\n2. The SIR 321 has been removed when the RF LED starts flashing.",
+		"reset": "Press pairing button and boost button simultaneously until RF LED starts flashing.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4045/SIR321%20BGX501-867%20R07.pdf"
 	}
 }

package/config/devices/0x0059/ssp_301_anz.json

@@ -43,9 +43,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To include the SSP 301 onto a network, put the controller into inclusion mode. Now press and hold the button on SSP 301 for 4 to 7 seconds then\nrelease. The network status LED will start flashing (twice per second) on successful start of inclusion process. On successful inclusion the LED will turn off.",
-		"exclusion": "To exclude the SSP 301 from a network, put the controller into exclusion mode. Now press and hold the button on SSP 301 for 4 to 7 seconds then\nrelease. After successful exclusion the network status LED will start flashing once per second, and the device will reset to factory default.",
-		"reset": "Please use this procedure only when the primary controller is missing or otherwise inoperable, Power cycle the device, press and hold the button\nfor 7-11 seconds within the 60 seconds of power cycle to put the device in factory default. It reset all configuration and association to factory default. It also removes the device from Z-Wave network",
+		"inclusion": "Press and hold the button on SSP 301 for 4 to 7 seconds then release. The network status LED will start flashing (twice per second) on successful start of inclusion process. On successful inclusion the LED will turn off",
+		"exclusion": "Press and hold the button on SSP 301 for 4 to 7 seconds then release. After successful exclusion the network status LED will start flashing once per second, and the device will reset to factory default",
+		"reset": "Power cycle the device, press and hold the button for 7-11 seconds within the 60 seconds of power cycle to put the device in factory default",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1246/SSP%20301%20User%20Manual%20for%20Web.pdf"
 	}
 }

package/config/devices/0x0059/ssp_302_anz.json

@@ -173,9 +173,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "To include the SSP 302 onto a network, put the controller into inclusion mode. Now, press and hold the button on SSP 302 for 4 to 7 seconds then release. The network status LED will start flashing (twice per second) on successful start of inclusion process. \nOn successful inclusion the LED will turn off",
-		"exclusion": "To exclude the SSP 302 from a network, put the controller into exclusion mode. Now, press and hold the button on SSP 302 for 4 to 7 seconds then release. The network status LED will start flashing (twice per second) on successful start of exclusion process.\nAfter successful exclusion the network status LED will start flashing once per second, and the device will reset to factory default.",
-		"reset": "Please use this procedure only when the primary controller is missing or otherwise inoperable. Power cycle the device and press and hold the button for more than 11 seconds and less than 15 seconds within the 60 seconds of power cycle to put the device in factory default, that include setting all the configuration, Association to factory default and removing the device from Z-Wave network",
+		"inclusion": "Press and hold the button on SSP 302 for 4 to 7 seconds then release. The network status LED will start flashing (twice per second) on successful start of inclusion process. On successful inclusion the LED will turn off",
+		"exclusion": "Press and hold the button on SSP 302 for 4 to 7 seconds then release. The network status LED will start flashing (twice per second) on successful start of exclusion process. After successful exclusion the network status LED will start flashing once per second, and the device will reset to factory default",
+		"reset": "Power cycle the device and press and hold the button for more than 11 seconds and less than 15 seconds within the 60 seconds of power cycle to put the device in factory default",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1271/SSP%20302%20User%20Manual%20for%20Web.pdf"
 	}
 }

package/config/devices/0x0059/ssr-302.json

@@ -25,9 +25,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "STEP 1: Ensure the LED is flashing RED on the SSR 302, if not follow the ‘Exclusion’ steps first.\nSTEP 2: Put the 3rd party controller into inclusion mode.\nSTEP 3: Press and hold both white buttons on the SSR 302 until the LED starts flashing green.\nThe SSR 302 has been added onto the network and the LED will go solid amber.\n\nNOTE: If the LED does not go solid amber then the add process has been unsuccessful",
+		"inclusion": "STEP 1: Ensure the LED is flashing RED on the SSR 302, if not follow the ‘Exclusion' steps first.\nSTEP 2: Put the 3rd party controller into inclusion mode.\nSTEP 3: Press and hold both white buttons on the SSR 302 until the LED starts flashing green.\nThe SSR 302 has been added onto the network and the LED will go solid amber.\n\nNOTE: If the LED does not go solid amber then the add process has been unsuccessful",
 		"exclusion": "STEP 1: Put the 3rd party controller into exclusion mode.\nSTEP 2: Press and hold the two white buttons on the SSR 302.\nThe SSR 302 has been removed from the network when the LED starts flashing red.\n\nNOTE: If the LED does not flash red then the remove process has been unsuccessful",
-		"reset": "\"Please use this procedure only when the primary controller is missing or otherwise inoperable.\"\n\nFollow ‘Exclusion’ steps",
+		"reset": "\"Please use this procedure only when the primary controller is missing or otherwise inoperable.\"\n\nFollow ‘Exclusion' steps",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1619/SSR%20302%20User%20Manual.pdf"
 	}
 }

package/config/devices/0x0063/14286_zw1001.json

@@ -23,7 +23,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the Program Button to add it in the network",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button on the smart dimmer to\nremove it from the network",
-		"reset": "1. Press and hold the button for at least 3 seconds. The LED light\nwill blink 5 times to confirm.\nNOTE: This should only be used in the event your network’s primary\ncontroller is missing or otherwise inoperable",
+		"reset": "1. Press and hold the button for at least 3 seconds. The LED light\nwill blink 5 times to confirm.\nNOTE: This should only be used in the event your network's primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2112/Binder1.pdf"
 	}
 }

package/config/devices/0x0063/14287_zw4002.json

@@ -47,7 +47,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.\n2. Once the controller is ready to include your device, press and release the top or bottom of the smart fan control switch (rocker) to include it in the network.\n3. Once your controller has confirmed the device has been included, refresh the Z-Wave network to optimize performance",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network. \n2. Once the controller is ready to Exclude your device, press and release the top or bottom of the wireless smart switch (rocker) to exclude it from the network",
-		"reset": "1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network’s primary controller is missing or otherwise inoperable",
+		"reset": "1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully.\nNote: This should only be used in the event your network's primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2506/Binder2.pdf"
 	}
 }

package/config/devices/0x0063/14288_zw1002.json

@@ -23,7 +23,7 @@
 	"metadata": {
 		"inclusion": "Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the Program Button to add it in the network",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button to remove it from the\nnetwork",
-		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network’s primary\ncontroller is missing or otherwise inoperable",
+		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network's primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2236/14288%20QSG%20v1.pdf"
 	}
 }

package/config/devices/0x0063/14293_zw4009.json

@@ -23,7 +23,7 @@
 	"metadata": {
 		"inclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to include a device to the Z-Wave network.\n2. Once the controller is ready to add your device,\npress toggle up and release to include it in the network",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified\ncontroller to remove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device,\npress toggle up or down to exclude it from the network",
-		"reset": "1. Quickly press ON (up) button three (3) times then\nimmediately press the OFF (down) button three\n(3) times. \nNote: This should only be used in the event your\nnetwork’s primary controller is missing or otherwise\ninoperable",
+		"reset": "1. Quickly press ON (up) button three (3) times then\nimmediately press the OFF (down) button three\n(3) times. \nNote: This should only be used in the event your\nnetwork's primary controller is missing or otherwise\ninoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2055/Binder2.pdf"
 	}
 }

package/config/devices/0x0063/14297_zw1002.json

@@ -26,7 +26,7 @@
 	"metadata": {
 		"inclusion": "Follow the instructions for your Z-Wave certified\ncontroller to add a device to the Z-Wave network.\n2. Once the controller is ready to add your device, press and\nrelease the Program Button to add it in the network",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified controller to\nremove a device from the Z-Wave network.\n2. Once the controller is ready to remove your device, press and\nrelease the manual/program button to remove it from the\nnetwork",
-		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network’s primary\ncontroller is missing or otherwise inoperable",
+		"reset": "Press the button 3 times, then press and hold the button for at least 3\nseconds. The LED will blink 5 times to confirm.\nNOTE: This should only be used in the event your network's primary\ncontroller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2236/14288%20QSG%20v1.pdf"
 	}
 }