@zwave-js/config 15.6.0 → 15.7.0

package/config/devices/0x011a/zw500dm.json

@@ -115,9 +115,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "When the primary controller is in the adding mode, flicks the paddle 3 times in the\n1.5 second. The primary controller will verify the adding, assign a node ID number\nfor the module",
-		"exclusion": "When the primary controller is in the removing mode, flicks the paddle 3 times in\nthe 1.5 second. The primary controller will verify the removing, remove the module\nfrom the current Z-Wave network, and the LED will blink when the module is on\npower",
-		"reset": "Flicks the program button 3 times in the 1.5 second then press once and hold for\n2 second.the device will send a device reset locally notification to controller. Then\nclear all of information for the network, and restore factory defaults, and reset the\nmodule. Use this procedure only in the event that the network primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Flick the paddle 3 times within 1.5 seconds.",
+		"exclusion": "Flick the paddle 3 times within 1.5 seconds. LED will blink when the module is powered.",
+		"reset": "1. Flick the program button 3 times within 1.5 seconds\n2. Press once and hold for 2 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1848/ZW500DM-CC%202016%205.19.pdf"
 	}
 }

package/config/devices/0x011a/zwn-rsm2.json

@@ -55,9 +55,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "When the controller is in add mode, press and release the program button of ZWN-RSM2 module,or Flick 3 times of the connected switch with Aux1 line(or Aux 2 line) in 1.5 second. Then the controller will add the module into current Z-Wave network",
-		"exclusion": "When the controller is in remove mode, press and release the program button of ZWN-RSM2 module, or Flick 3 times of the connected switch with Aux1 line (or Aux2 line) in 1.5 second. Then the controller will remove the module from current Z-Wave network",
-		"reset": "Once program button is pressed and hold for 10 second, the device will send a device reset locally notification to controller. Then clear all of information for the network, and restore factory defaults, and reset the module. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press and release the program button of the ZWN-RSM2 module, or flick the connected switch on the Aux1 line (or Aux2 line) 3 times within 1.5 seconds.",
+		"exclusion": "Press and release the program button of the ZWN-RSM2 module, or flick the connected switch on the Aux1 line (or Aux2 line) 3 times within 1.5 seconds.",
+		"reset": "Press and hold the program button for 10 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2242/ZWN-RSM2%202017-2-28.pdf"
 	},
 	"compat": {

package/config/devices/0x011b/eedomus.json

@@ -16,7 +16,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "You can proceed to a Z-Wave chip factory reset in order to do a fresh installation of your network.\n\nWhen doing that the Home ID of your network will change and your devices need to be excluded (in order to be reset) and included again.\n\nTo perform a factory reset, click on :\nConfiguration / Add or remove a device / Advanced Z-Wave functions / Reset Z-Wave controller\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. \nIf this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "1. Click on Configuration\n2. Select Add or remove a device\n3. Choose Advanced Z-Wave functions\n4. Select Reset Z-Wave controller",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3582/eedomus_guide_en.pdf"
 	}
 }

package/config/devices/0x0127/xtlpl.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Use the initialize defaults function to set a panel’s programmed memory back to the factory defaults and remove any existing Z-Wave programming. Follow these steps to initialize a panel’s defaults:\n1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"reset": "Use the initialize defaults function to set a panel's programmed memory back to the factory defaults and remove any existing Z-Wave programming. Follow these steps to initialize a panel's defaults:\n1. Reset the panel.\n2. Enter 6653 (PROG) at a keypad and press CMD to enter the panel programming menu.\n3. Press CMD until INITIALIZATION displays and press a top row select key or area.\n4. Press CMD until DEFAULTS? NO YES displays. Press the select key or area under YES.\n5. Press the select key or area under YES when SURE? YES NO displays.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2685/XTLplus%20zwave%20certification.pdf"
 	}
 }

package/config/devices/0x0129/sr-bx-zw.json

@@ -54,7 +54,7 @@
 	"metadata": {
 		"inclusion": "ADDING THE SIREN\nThis product can be added and operate in any compatible Z-Wave network. All non-battery operated nodes within the network will act as repeaters, regardless of vendor, to increase reliability of the network.\nAdding steps:\n• Turn on the battery power switch to activate\nthe pre-inserted batteries.\n• The Siren will emit a 2-tone beep.\n• Put the Z-Wave controller into adding or\nLearning mode (please refer to the Z-Wave\ncontroller manual).\n• Within 1.5 seconds, press the Siren learn button\n3 times.\n• Refer to the operation manual of the Z-Wave\ncontroller to complete the learn-in process.\n• If the Siren has already been added (learnt) into\nanother Z-Wave controller, or if the Siren is unable\nto be learnt into the current Z-Wave controller,\nplease remove it first (see Removing the siren below)\nbefore attempting to add it into the current\nZ-Wave controller",
 		"exclusion": "REMOVING THE SIREN\nThe Siren must be removed from any existing Z-Wave network before being added into a new Z-Wave network. There are two methods available to remove a device.\nRemoving Mode\n• Put the existing Z-Wave controller into Removing Mode (please refer to the Z-Wave controller manual).\n• Within 1.5 seconds, press the learn button 3 times and the Siren will be removed from the existing Z-Wave network.\n• The Siren is now ready to be added to a new Z-Wave controller",
-		"reset": "Factory Reset (Only use this when the existing Z-Wave controller is missing or inoperable).\n• Turn off battery power switch and disconnect 9V power adaptor (if present).\n• Press and hold the learn button.\n• While holding the learn button, power on the Siren (power switch ON and reconnect the 9V power adaptor). Keep holding for 10 seconds to complete the factory reset.\n• Please note that the existing Z-Wave controller will still retain the Siren’s Z-Wave setting. Please refer to the Z-Wave controller manual on remove procedures. Only use this when the existing Z-Wave controller is missing or inoperable.\n• The Siren is now ready to be added to a new Z-Wave controller",
+		"reset": "Factory Reset (Only use this when the existing Z-Wave controller is missing or inoperable).\n• Turn off battery power switch and disconnect 9V power adaptor (if present).\n• Press and hold the learn button.\n• While holding the learn button, power on the Siren (power switch ON and reconnect the 9V power adaptor). Keep holding for 10 seconds to complete the factory reset.\n• Please note that the existing Z-Wave controller will still retain the Siren's Z-Wave setting. Please refer to the Z-Wave controller manual on remove procedures. Only use this when the existing Z-Wave controller is missing or inoperable.\n• The Siren is now ready to be added to a new Z-Wave controller",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2039/YSL_External_Siren_SR-BX-ZW_1C.pdf"
 	}
 }

package/config/devices/0x012a/iq_dimmer.json

@@ -67,9 +67,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the top of the IQ Dimmer. The controller should indicate that the new device was added successfully.\n3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home.",
-		"exclusion": "1. Place your network controller into exclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the top of the IQ Dimmer. The controller should indicate that the new device was added successfully.\n3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home.",
-		"reset": "If Inclusion still fails after the 2nd attempt, you need to first reset the IQ Dimmer before repeating the above step. The manual reset method is as follows:\n1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plug of the appliance from the IQ Dimmer (if plugged in).\n2. Press and hold the button on the IQ Dimmer.\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed.",
+		"inclusion": "Single click the button on the top of the IQ Dimmer.",
+		"exclusion": "Single click the button on the top of the IQ Dimmer.",
+		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plug of the appliance from the IQ Dimmer (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4089/IQ%20Dimmer%20User%20Guide%20031921.pdf"
 	}
 }

package/config/devices/0x012a/iq_outlet.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the top of the IQ Outlet. The controller should indicate that the new device was added successfully.\n3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.",
-		"exclusion": "1. Place your network controller into exclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the top of the IQ Outlet. The controller should indicate that the new device was added successfully.\n3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.",
-		"reset": "Please use this procedure only when the network primary controller is missing or otherwise inoperable. The manual reset method is as follows:\n1. Unplug the IQ Outlet from the AC outlet and also unplug the power plug of the appliance from the IQ Outlet (if plugged in).\n2. Press and hold the button on the IQ Outlet .\n3. Plug the IQ Outlet back into the AC outlet with the button pressed.",
+		"inclusion": "Single click the button on the top of the IQ Outlet.",
+		"exclusion": "Single click the button on the top of the IQ Outlet.",
+		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plug of the appliance from the IQ Outlet (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4133/IQ%20Outlet%20User%20Guide%20032421.pdf"
 	}
 }

package/config/devices/0x012a/iqpanel2.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "Swipe down to access “Settings” < Touch “Advanced Settings” < Enter code < Touch “Installation” < Touch “Devices” < Touch “Z-Wave Devices” < Touch “Add Device” < Touch “Pair” < Press pair or learn button on device < Adjust device name as needed < Select “Automation” < Click “Add” to save",
-		"exclusion": "Swipe down to access “Settings” < Touch “Advanced Settings” < Enter code < Touch “Installation” < Touch “Devices” < Touch “Z-Wave Devices” < Touch “Delete failed device from panel” < Check boxes next to devices you want to delete < Touch “Delete”",
-		"reset": "Swipe down to access “Settings” < Touch “Advanced Settings” < Enter code < Touch “Installation” < Touch “Devices” < Touch “Z-Wave Devices” < Touch “Remove All Devices”",
+		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device\n10. Adjust device name as needed\n11. Select Automation\n12. Click Add to save",
+		"exclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Delete failed device from panel\n8. Check boxes next to devices you want to delete\n9. Touch Delete",
+		"reset": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Remove All Devices",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3092/IQ%20Panel%20Installation%20Manual%202.2.1%20FINAL.pdf"
 	}
 }

package/config/devices/0x012a/qs9201-1208-840.json

@@ -27,9 +27,9 @@
 		}
 	},
 	"metadata": {
-		"inclusion": "Swipe down to access “Settings” < Touch “Advanced Settings” < Enter code < Touch “Installation” < Touch “Devices” < Touch “Z-Wave Devices” < Touch “Add Device” < Touch “Pair” < Press pair or learn button on device < Adjust device name as needed < Select “Automation” < Click “Add” to save",
-		"exclusion": "Swipe down to access “Settings” < Touch “Advanced Settings” < Enter code < Touch “Installation” < Touch “Devices” < Touch “Z-Wave Devices” < Touch “Delete failed device from panel” < Check boxes next to devices you want to delete < Touch “Delete”",
-		"reset": "1. On home menu, swipe down from the top of the screen. A pulldown menu should appear.\n2. Press the SETTINGS icon.\n3. Press the ADVANCED SETTINGS icon.\n4. Enter in installer code.\n5. Press the INSTALLATION icon.\n6. Press the DEVICES icon.\n7. Press the Z-WAVE DEVICES icon.\n8. Press the REMOVE ALL DEVICES icon.\n9. Press YES on the confirmation dialog to perform a reset.",
+		"inclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Add Device\n8. Touch Pair\n9. Press pair or learn button on device\n10. Adjust device name as needed\n11. Select Automation\n12. Click Add to save",
+		"exclusion": "1. Swipe down to access Settings\n2. Touch Advanced Settings\n3. Enter code\n4. Touch Installation\n5. Touch Devices\n6. Touch Z-Wave Devices\n7. Touch Delete failed device from panel\n8. Check boxes next to devices you want to delete\n9. Touch Delete",
+		"reset": "1. Swipe down from the top of the screen\n2. Touch Settings\n3. Touch Advanced Settings\n4. Enter installer code\n5. Touch Installation\n6. Touch Devices\n7. Touch Z-Wave Devices\n8. Touch Remove All Devices\n9. Touch Yes to confirm",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3821/IQ%20Panel%20Installation%20Manual%202.5.0%20FINAL.pdf"
 	}
 }

package/config/devices/0x012a/qz2130-840.json

@@ -26,9 +26,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Inclusion: Add the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add the IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added using the traditional method for Z-Wave as follows:\n\n1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was added successfully.\n3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.\n\nIf the controller shows it failed, repeat the procedure.",
-		"exclusion": "Exclusion: Remove the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on removing devices to the network. In addition, the device can be removed using the traditional method for Z-Wave as follows:\n\n1. Place your network controller into Exclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was removed successfully.\n\nIf the controller shows it failed, repeat the procedure.",
-		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed\nAfter 3 seconds, release the button. If you see the button blink, that means that IQ Outlet has been reset successfully.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Single click the button on the front of the IQ Outlet.",
+		"exclusion": "Single click the button on the front of the IQ Outlet.",
+		"reset": "1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Outlet\n3. Plug the IQ Outlet back into the AC outlet with the button pressed\n4. After 3 seconds, release the button\nIf you see the button blink, the IQ Outlet has been reset successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3032/IQ%20Outlet%20User%20Manual%20060718.pdf"
 	}
 }

package/config/devices/0x012a/qz2140-840.json

@@ -45,9 +45,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the front of the IQ Dimmer. The controller should indicate that the new device was added successfully.\n3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home",
-		"exclusion": "1. Place your network controller into exclusion mode by following the controller manufacturer's instructions.\n2. When the controller is ready, single click the button on the front of the IQ Dimmer. The controller should indicate that the new device was removed successfully.\n3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home",
-		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed. After 3 seconds, release the button. If you see the button blink, that means that IQ Dimmer has been reset successfully.\n\nPlease use this procedure only when the network primary controller is missing or otherwise inoperable.",
+		"inclusion": "Single click the button on the front of the IQ Dimmer.",
+		"exclusion": "Single click the button on the front of the IQ Dimmer.",
+		"reset": "1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)\n2. Press and hold the button on the IQ Dimmer\n3. Plug the IQ Dimmer back into the AC outlet with the button pressed. After 3 seconds, release the button\nThe button will blink to confirm successful reset.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2912/IQ%20Dimmer%20UG%20Online.pdf"
 	}
 }

package/config/devices/0x012a/qz2142-840.json

@@ -222,9 +222,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "When prompted by your primary controller, click the button three times in one second",
-		"exclusion": "When prompted by your primary controller, click the button three times in one second",
-		"reset": "Press click Z-Wave button 3 times quickly, and hold for at least 10 seconds at the third time to restore the device to the factory",
+		"inclusion": "Click the button three times within one second.",
+		"exclusion": "Click the button three times within one second.",
+		"reset": "Click the Z-Wave button 3 times quickly, and hold for at least 10 seconds on the third click to restore factory settings.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4463/IQSmartDimmerManual_v2.pdf"
 	}
 }

package/config/devices/0x0131/mh-p220.json

@@ -155,7 +155,7 @@
 		{
 			"#": "8",
 			"label": "Single Dimming Step Size (Manual)",
-			"description": "1~99 percentage value (modification isn’t recommended)",
+			"description": "1~99 percentage value (modification isn't recommended)",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 99,
@@ -173,7 +173,7 @@
 		{
 			"#": "10",
 			"label": "Single Dimming Step Size (Auto)",
-			"description": "1~99 percentage value (modification isn’t recommended)",
+			"description": "1~99 percentage value (modification isn't recommended)",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 99,

package/config/devices/0x0131/ne_nas_ab02z.json

@@ -160,9 +160,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "The indoor siren can be included to the Z-Wave network by pressing the code button.\n1) Disassemble the siren and insert the battery into\nthe siren. Make sure the device is located within\nthe direct range of the controller.\n2) Set the controller into the inclusion mode (see\nmain controller’s operating manual).\n3) Quickly triple click the code button, LED light will\nflash red for 5 times.\n4) The Indoor siren will be detected and included\nin the Z-Wave network.\n5) Wait for the main controller to configure the siren.\n\nSMART START. This product also supports Z-Wave Smart Start option which enables easier inclusion. QR code for SmartStart inclusion is printed on the battery cover. SmartStart option is only possible when network controller is also supporting SmartStart",
-		"exclusion": "1) Make sure the siren is connected to power source. 2) Set the main controller into the exclusion mode\n(see main controller’s operating manual).\n3) Quickly triple click the code button, LED light\nwill flash red for 5 times\n4) Wait for the main controller to remove the sensor",
-		"reset": "Reset procedure will remove all information on the Z-Wave network or Z-Wave controller and restore the sensor to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\n1) Remove the sensor’s cover\n2) Make sure the sensor is connected to power source \n3) Press the code button for 10 seconds, LED will flash blue for 3 seconds\n4) Release the code button\n\nNote: \nWhen the siren is being restored to factory settings, please make sure power source is connected.",
+		"inclusion": "The indoor siren can be included to the Z-Wave network by pressing the code button.\n1) Disassemble the siren and insert the battery into\nthe siren. Make sure the device is located within\nthe direct range of the controller.\n2) Set the controller into the inclusion mode (see\nmain controller's operating manual).\n3) Quickly triple click the code button, LED light will\nflash red for 5 times.\n4) The Indoor siren will be detected and included\nin the Z-Wave network.\n5) Wait for the main controller to configure the siren.\n\nSMART START. This product also supports Z-Wave Smart Start option which enables easier inclusion. QR code for SmartStart inclusion is printed on the battery cover. SmartStart option is only possible when network controller is also supporting SmartStart",
+		"exclusion": "1) Make sure the siren is connected to power source. 2) Set the main controller into the exclusion mode\n(see main controller's operating manual).\n3) Quickly triple click the code button, LED light\nwill flash red for 5 times\n4) Wait for the main controller to remove the sensor",
+		"reset": "Reset procedure will remove all information on the Z-Wave network or Z-Wave controller and restore the sensor to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.\n\n1) Remove the sensor's cover\n2) Make sure the sensor is connected to power source \n3) Press the code button for 10 seconds, LED will flash blue for 3 seconds\n4) Release the code button\n\nNote: \nWhen the siren is being restored to factory settings, please make sure power source is connected.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3046/ne-nas-ab02z.eu%20-%20Zipato%20INDOOR%20SIREN-waveEU_UserManual_v1.3.pdf"
 	}
 }

package/config/devices/0x0131/vs-zd2301.json

@@ -68,8 +68,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Put the Z-WaveTM Interface Controller into\n“inclusion” mode, and following its instruction to add the ZD2301 to your controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
-		"exclusion": "Put the Z-WaveTM Interface\nController into “exclusion” mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
+		"inclusion": "Put the Z-WaveTM Interface Controller into\n'inclusion' mode, and following its instruction to add the ZD2301 to your controller. To get in the 'inclusion' mode, the distance between sensor and controller is suggested to be one meter. Press the program switch of ZD2301 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds",
+		"exclusion": "Put the Z-WaveTM Interface\nController into 'exclusion' mode, and following its instruction to delete the ZD2301 from your controller. Press the program switch of ZD2301 for 1 second at least to be excluded",
 		"reset": "All user and network settings will be cleared and the device reset to factory\ndefaults when the device is excluded.\n\nPlease use this procedure only in the event if the network\ncontroller is missing or is otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2346/zp2301.pdf"
 	}

package/config/devices/0x0131/zb_zw_g.json

@@ -25,7 +25,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "* Navigate to Z-Wave network management tools\n* Click the “Z-WAVE RESET” button and follow onscreen instructions",
+		"reset": "* Navigate to Z-Wave network management tools\n* Click the 'Z-WAVE RESET' button and follow onscreen instructions",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1409/Zipato%20Z-Wave%20User%20Manual%2021.07.2015%20-%20144DPI.pdf"
 	}
 }

package/config/devices/0x013c/nsg-ab-02.json

@@ -94,8 +94,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing On/Off button three times within 2 seconds will enter inclusion mode.",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n 2. Pressing On/Off button three times within 2 seconds will enter exclusion mode. \n3. Node ID has been excluded",
-		"reset": "Use this procedure only in the event that the primary controller is lost or otherwise inoperable. \n1. Pressing On/Off button three times within 2 seconds will enter inclusion mode. \n2. Within 1 second, press On/Off button again for 5 seconds. \n3. IDs are excluded"
+		"inclusion": "Press the On/Off button three times within 2 seconds.",
+		"exclusion": "Press the On/Off button three times within 2 seconds.",
+		"reset": "1. Press the On/Off button three times within 2 seconds\n2. Within 1 second, press the On/Off button again for 5 seconds"
 	}
 }

package/config/devices/0x013c/pac01.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the\ncontroller manufacturer.\n2. Pressing Include button of PAC01 three times within 2 seconds will enter inclusion mode.",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the\ncontroller manufacturer.\n2. Pressing Include button of PAC01 three times within 2 seconds will enter exclusion mode. \n3. Node ID has been excluded",
-		"reset": "1. Pressing Include button of PAC01 three times within 2 seconds will enter inclusion mode. \n2. Within 1 second, press Include button of PAC01 again for 5 seconds. \n3. IDs are excluded",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3619/PAC01_UserManual.pdf"
 	}
 }

package/config/devices/0x013c/pad07.json

@@ -102,9 +102,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing Include button of PAD07 three times within 2 seconds will enter exclusion mode.\n3. Node ID has been excluded.",
-		"reset": "1. Pressing Include button of PAD07 three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press Include button of PAD07 again for 5 seconds.\n3. IDs are excluded.\n\n*Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2356/PAD07-A1%20manual-20170413.pdf"
 	}
 }

package/config/devices/0x013c/pad09.json

@@ -44,9 +44,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1.check Z-WaveTM Controller entered inclusion mode.\n2.Pressing Include button of PAD09 three times within 2 seconds will \nenter inclusion mode.",
-		"exclusion": "1.check Z-WaveTM Controller entered exclusion mode.\n2.Pressing Include button of PAD09 three times within 2 seconds will \nenter exclusion mode",
-		"reset": "1. Pressing Include button of PAD09 three times within 2 seconds will enter inclusion mode. \n2. Within 1 second, press Include button of PAD09 again for 5 seconds. \n3. IDs are excluded. \n\nnote : Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3142/PAD09_UserManual_Philio.pdf"
 	}
 }

package/config/devices/0x013c/pad15.json

@@ -84,9 +84,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Add(Classic Inclusion) : 1. Put your Z-Wave™ controller into inclusion mode by following the instructions\nprovided by the controller manufacturer. 2. Press the include button three times within 3 seconds to enter\ninclusion mode",
-		"exclusion": "Remove (Exclusion) 1. Put your Z-Wave™ controller into exclusion mode by following the instructions\nprovided by the controller manufacturer. 2. Press the include button three times within 3 seconds to enter\nexclusion mode. 3. Node ID will be excluded",
-		"reset": "Reset : 1. Press the include button four times within 3 seconds and hold on the button press without\nreleasing. 2. Keep pressing the button for 3 seconds then LED will be o ,release the button within 2 seconds.\n3. Device has been reset. ※Function Reset : Please use this procedure only when the network primary\ncontroller is missing or otherwise inoperable",
+		"inclusion": "Press the include button three times within 3 seconds.",
+		"exclusion": "Press the include button three times within 3 seconds.",
+		"reset": "1. Press the include button four times within 3 seconds and hold on the fourth press\n2. Keep pressing for 3 seconds until the LED turns off\n3. Release the button within 2 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4209/PAD15_UserManual_V3.pdf"
 	}
 }

package/config/devices/0x013c/pan04.json

@@ -221,9 +221,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter exclusion mode.",
-		"reset": "1. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press On/Off button again for 5 seconds.\nUse this procedure only in the event that the primary controller is lost or otherwise inoperable.",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the On/Off button for 5 seconds",
 		"manual": "https://www.zwavetaiwan.com.tw/s/PAN04-manual-20181015-1.pdf"
 	}
 }

package/config/devices/0x013c/pan15-1-nes.json

@@ -116,9 +116,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1.Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing On/Off button three times within 2 seconds will enter inclusion mode.",
-		"exclusion": "1.Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n 2.Pressing On/Off button three times within 2 seconds will enter exclusion mode. \n3.Node ID has been excluded",
-		"reset": "Use this procedure only in the event that the primary controller is lost or otherwise inoperable. \n1. Pressing On/Off button three times within 2 seconds will enter inclusion mode. \n2.Within 1 second, press On/Off button again for 5 seconds. \n3.IDs are excluded",
+		"inclusion": "Press the On/Off button three times within 2 seconds.",
+		"exclusion": "Press the On/Off button three times within 2 seconds.",
+		"reset": "1. Press the On/Off button three times within 2 seconds\n2. Within 1 second, press the On/Off button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1647/PAN15-NES-manual-20160123.pdf"
 	}
 }

package/config/devices/0x013c/pan26.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1.Set your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.\n2. Press the middle button (button ⑤) three times within 2 seconds intervals and device will enter inclusion mode.\n3. Node ID is included",
-		"exclusion": "1.Set your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Press the middle button (button ⑤) three times within 2 seconds intervals and device will enter exclusion mode.\n3. Node ID is excluded",
-		"reset": "1.Press the middle button (button ⑤) four times and hold the button on the 4th time for about 3~10 seconds, then release button.\n2.IDs will get excluded and all settings will be reset",
+		"inclusion": "Press the middle button (button ⑤) three times within 2 seconds.",
+		"exclusion": "Press the middle button (button ⑤) three times within 2 seconds.",
+		"reset": "Press and hold the middle button (button ⑤) four times, keeping it held on the 4th press for 3-10 seconds, then release.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3603/PAN26%20manual-20190806.pdf"
 	}
 }

package/config/devices/0x013c/pan30.json

@@ -144,9 +144,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.\n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter exclusion mode.\n3. Node ID has been excluded",
-		"reset": "1. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press On/Off button again for 5 seconds.\n3. IDs are excluded",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the On/Off button for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4188/PAN30%20manual-20210602.pdf"
 	}
 }

package/config/devices/0x013c/pan34.json

@@ -96,9 +96,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. \n2. Pressing INCLUDE_BUTTON three times within 2 seconds will enter exclusion mode. \n3. Node ID has been excluded",
-		"reset": "1. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode. \n2. Within 1 second, press On/Off button again for 5 seconds. \n3. IDs are excluded",
+		"inclusion": "Press the Include Button three times within 2 seconds.",
+		"exclusion": "Press the Include Button three times within 2 seconds.",
+		"reset": "1. Press the Include Button three times within 2 seconds\n2. Within 1 second, press the On/Off button for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4250/PAN34%20manual-20210713.pdf"
 	}
 }

package/config/devices/0x013c/pau05.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the\ncontroller manufacturer.\n2. Pressing Include button of PAU05 three times within 2 seconds will enter inclusion mode.",
-		"exclusion": "1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the\ncontroller manufacturer.\n2. Pressing Include button of PAU05 three times within 2 seconds will enter exclusion mode.\n3. Node ID has been excluded.",
-		"reset": "1. Pressing Include button of PAU05 three times within 2 seconds will enter inclusion mode.\n2. Within 1 second, press Include button of PAU05 again for 5 seconds.\n3. IDs are excluded.",
+		"inclusion": "Press the Include button three times within 2 seconds.",
+		"exclusion": "Press the Include button three times within 2 seconds.",
+		"reset": "1. Press the Include button three times within 2 seconds\n2. Within 1 second, press the Include button again for 5 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3611/PAU05_UserManual_V1.pdf"
 	}
 }

package/config/devices/0x013c/psa03-us.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "1.check Z-WaveTM Controller entered inclusion mode.\n2.Press the Add/Remove function “enterPC” is enter “0000”(default) enterPC->enter-> 1 -> 0 ->enter\n3.After add successful, it will have twice beep sounds.if inclusion fail it will have five beep.\nNotice 1 : if you reset doorlock ,you have to do OPERATING INSTRUCTION no.1(door handling identification process )\nNotice 2:if Door lock in learn mode,device can stop on operation setting mode,until success include or 60s time out.",
-		"exclusion": "1.check Z-WaveTM Controller entered exclusion mode.\n2.Press the Add/Remove function “enterPC” is enter “0000”(default) enterPC->enter-> 1 -> 0 ->enter\n3.After remove successful, it will have twice beep sounds.if exclusion fail it will have five beep.\nNotice 1 : if you reset doorlock ,you have to do OPERATING INSTRUCTION no.1(door handling identification process )\nNotice 2:if Door lock in learn mode,device can stop on operation setting mode,until success include or 60s time out.",
-		"reset": "1.Press the black key in battery cover, and until 5s time up.device can beep two times.\n2.Device can send resetlocally notification\n\nnote : Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"inclusion": "1. Enter the Programming Code (default: 0000) and press enter\n2. Press 1, then 0, then enter",
+		"exclusion": "1. Enter the Programming Code (default: 0000) and press enter\n2. Press 1, then 0, then enter",
+		"reset": "Press and hold the black key in the battery cover for 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2987/PSA03_UserManual_Philio_V12.pdf"
 	}
 }

package/config/devices/0x013c/psc03.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Reset the Z-Wave controller. It will reset the Z-Wave controller and will be assign a new Z-Wave home id. \n\nPlease click \"Reset Gateway\", it will show \"Reset\" message\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.\n\n(Please check your user document, the detail in 3.1.3)",
+		"reset": "Click Reset Gateway to reset the Z-Wave controller.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2964/PSC03%20Gateway%20User%20ManualV1.1_20180613.pdf"
 	}
 }

package/config/devices/0x013c/pse04.json

@@ -154,9 +154,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave Controller entered inclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the LED will light ON 1 second",
-		"exclusion": "1. Have Z-Wave Controller entered exclusion mode.\n2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.\n3. Node ID has been excluded",
-		"reset": "1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are excluded and all settings will reset to factory default",
+		"inclusion": "Press the tamper key three times within 1.5 seconds.",
+		"exclusion": "Press the tamper key three times within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the tamper key within 2 seconds after the LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4191/PSE04_UserManual_Philio_V3_Certification_2.pdf"
 	}
 }

package/config/devices/0x013c/psg04.json

@@ -28,9 +28,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-WaveTM Controller entered inclusion mode.\n2. Pressing button three times within 1.5 seconds to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-WaveTM Controller about 20 seconds",
-		"exclusion": "1. Have Z-WaveTM Controller entered exclusion mode.\n2. Pressing button three times within 1.5 seconds to enter the exclusion mode.\nNode ID has been removed.",
-		"reset": "1. Pressing button four times within 1.5 seconds and do not release the button in the 4th pressed.\n2. After 3 secands and release the button within 2 seconds.\n3. IDs are removed and all settings will reset to factory default",
+		"inclusion": "Press the button three times within 1.5 seconds.",
+		"exclusion": "Press the button three times within 1.5 seconds.",
+		"reset": "1. Press the button four times within 1.5 seconds and hold on the fourth press\n2. After 3 seconds, release the button within 2 seconds",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3672/PSG04_UserManual-V1.pdf"
 	}
 }

package/config/devices/0x013c/psk01.json

@@ -63,9 +63,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-WaveTM Controller enter inclusion mode.\n2. Enter the Programming Code (PC) by pressing the correct number keys (default programming code is 0000) and then enter, then press 1 and 0 and enter.\n3. After successful addition, the device buzzer will beep twice.",
-		"exclusion": "1. Have Z-WaveTM Controller enter exclusion mode.\n2. Enter the Programming Code (PC) by pressing the correct number keys (default programming code is 0000) and then enter, then press 1 and 0 and enter.\n3. After successful removal, the device buzzer will beep twice.",
-		"reset": "Method 1. Enter the Programming Code (PC) by pressing the correct number keys (default programming code is 0000) and then enter, then press 9 and enter.\nMethod 2. Press tamper key 3 times in 1.5 seconds. 3 long beeps will occur after two seconds on successful reset.",
+		"inclusion": "1. Enter the Programming Code (default is 0000) and press enter\n2. Press 1, then 0, then enter",
+		"exclusion": "1. Enter the Programming Code (default is 0000) and press enter\n2. Press 1, then 0, then enter",
+		"reset": "Method 1: Enter the Programming Code (default is 0000), press enter, then press 9 and enter.\n\nMethod 2: Press the tamper key 3 times in 1.5 seconds.",
 		"manual": "https://www.zwavetaiwan.com.tw/s/PSK01_UserManual-A2-20240731.pdf"
 	}
 }

package/config/devices/0x013c/psm02.json

@@ -274,8 +274,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Turn the primary controller of Z-Wave network into inclusion mode, triple click tamper switch within 1.5 seconds",
-		"exclusion": "Turn the primary controller of Z-Wave network into exclusion mode, triple click tamper switch within 1.5 seconds",
-		"reset": "Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th  pressed, and the LED will light on. After 3 seconds the LED will turn off, after that within 2 seconds, release the tamper key. If successful, the LED will light on one second. Otherwise, the LED will flash once. IDs are excluded and all settings will reset to factory default."
+		"inclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"exclusion": "Triple-click the tamper switch within 1.5 seconds.",
+		"reset": "1. Press and hold the tamper key four times within 1.5 seconds, keeping it held on the 4th press until the LED lights up\n2. Release the tamper key within 2 seconds after the LED turns off."
 	}
 }

package/config/devices/0x013c/psm08.json

@@ -15,9 +15,9 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"inclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered inclusion mode.\n2. Pressing button once to enter the inclusion mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds",
-		"exclusion": "There is a button on PSM08.\n1. Have Z-Wave™ Controller entered exclusion mode.\n2. Pressing button once to enter the exclusion mode",
-		"reset": "There is a button on PSM08.\n1. Pressing button for about 5 seconds.\n2. IDs are excluded and all settings will reset to factory default.\nNotice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable",
+		"inclusion": "Press the button once.",
+		"exclusion": "Press the button once.",
+		"reset": "Press the button for about 5 seconds.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2915/PSM08_manual-20161103.pdf"
 	}
 }

package/config/devices/0x013c/psm09.json

@@ -28,9 +28,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Check Z-WaveTM Controller enter inclusion mode. Pressing tamper key three times within 3 seconds to enter the inclusion mode. If the addition is successful, the LED will flash slowly.",
-		"exclusion": "Check Z-WaveTM Controller enter exclusion mode. Pressing tamper key three times within 3 seconds to enter the exclusion mode. If the removal is successful, the code light will flash for 30 seconds.",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\nPress the button three times in three seconds, then LED will flash for one second slowly. Press the button again and hold, the LED will light up, after about three seconds, the LED will off. Please release the button in two seconds. If the clearing is successful, the LED will flash one time per second. If it fails, the LED will flash quickly.",
+		"inclusion": "Press the tamper key three times within 3 seconds. If successful, the LED will flash slowly.",
+		"exclusion": "Press the tamper key three times within 3 seconds. If successful, the code light will flash for 30 seconds.",
+		"reset": "1. Press the button three times in three seconds\n2. The LED will flash slowly for one second\n3. Press and hold the button until the LED lights up\n4. After about three seconds, the LED will turn off\n5. Release the button within two seconds\nIf successful, the LED will flash once per second.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3462/PSM09_UserManual_0624.pdf"
 	}
 }

package/config/devices/0x013c/psr03-a.json

@@ -65,9 +65,9 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Have Z-Wave™ Controller entered add mode.\n2. Press the key three times within 1.5 seconds to enter the add mode.\n3. After add successful, the device will wake to receive the setting command from Z-Wave ™ Controller about 20 seconds",
-		"exclusion": "1. Have Z-Wave ™ Controller entered remove mode.\n2. Press the key three times within 1.5 seconds to enter the \nremove mode.\nNode ID has been excluded",
-		"reset": "Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.\n1. Press the key three times,and do not release the key in the 4 th pressed, and the LED will light ON.\n2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the keys. If successful, the LED will light ON one second. Otherwise, the LED will flash once.\n3. IDs are remove and all settings will reset to factory \ndefault",
+		"inclusion": "Press the key three times within 1.5 seconds.",
+		"exclusion": "Press the key three times within 1.5 seconds.",
+		"reset": "1. Press and hold the key four times within 1.5 seconds, keeping it held on the 4th press\n2. Wait for the LED to light up for 3 seconds, then turn off\n3. Release the key within 2 seconds after the LED turns off",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1407/PSR03_ABC_version_Manual.pdf"
 	},
 	"compat": {