@oriro/orirocli 0.1.8 → 0.1.11

package/skills/trades/trades-hvac/SKILL.md

@@ -1,80 +1,80 @@
----
-watermark: ORIRO
-disable-model-invocation: true
-name: trades-hvac
-provider: ORIRO.ai
-copyright: Copyright (c) 2026 ORIRO.ai
-description: >
-
-  HVAC — heating, cooling, ventilation principles, maintenance, troubleshooting, and energy efficiency.
-
-
-
-
-  Sources: USDA, OSHA, trade association guidelines, professional kitchen standards.
----
-
-# HVAC
-
-## How heating and cooling systems work
-
-### Forced-air systems (most common in US)
-
-**Furnace:** Burns gas (or propane, oil) to heat air. Blower distributes heated air through ducts.
-**Air conditioning (split system):** Refrigerant cycles between indoor unit (absorbs heat from indoor air) and outdoor unit (releases heat outside). Cooling is heat removal, not cold creation.
-**Heat pump:** Refrigerant-based like AC but can reverse cycle to provide heat. More efficient than electric resistance heat. Types: Air-source (outdoor unit), Ground-source (geothermal — higher efficiency, higher cost).
-**Ductwork:** Delivers conditioned air. Return ducts bring air back. Leaky ducts: 20-30% efficiency loss common.
-
-### Efficiency ratings
-
-**Furnace:** AFUE (Annual Fuel Utilization Efficiency). 80%+ = good; 95%+ = high-efficiency condensing.
-**Air conditioner:** SEER2 (Seasonal Energy Efficiency Ratio). 14-16 = standard; 18+ = high-efficiency.
-**Heat pump:** HSPF2 (heating), SEER2 (cooling). Higher = more efficient.
-
-## Maintenance schedule
-
-**Monthly:** Check and replace air filter. A clogged filter: Reduces airflow → strain on system → higher energy use → shorter equipment life. MERV 8-13 filters balance filtration with airflow.
-
-**Spring (before cooling season):**
-Clean AC condenser coils (outdoor unit). Clear debris around outdoor unit (12" clearance).
-Check refrigerant charge (professional). Schedule professional tune-up for AC.
-
-**Fall (before heating season):**
-Schedule professional furnace tune-up. Replace filter.
-Test carbon monoxide detectors.
-Check heat exchanger for cracks (professional — cracked heat exchanger = CO hazard).
-
-**Annual:** Professional HVAC inspection and tune-up. Clean evaporator coil (indoor) as needed.
-
-## Troubleshooting common problems
-
-**No cooling/heating:**
-Check thermostat settings and batteries.
-Check circuit breaker (AC on dedicated circuit; high-voltage contactor in outdoor unit can trip).
-Check air filter (clogged filter causes freeze-up).
-Check outdoor unit — is it running?
-
-**Poor airflow:**
-Dirty filter (#1 cause).
-Blocked/closed supply or return vents.
-Damaged ductwork.
-
-**Water around indoor unit:**
-Condensate drain clogged. Flush with bleach water solution.
-Frozen evaporator coil thawing (caused by: dirty filter, low refrigerant, restricted airflow).
-
-**High energy bills:**
-Air filter. Leaky ducts. Refrigerant charge. Equipment aging. Poor insulation/sealing.
-
-## When to call a professional
-
-Refrigerant handling: Illegal without EPA certification.
-Gas line work: Always.
-Electrical within the unit beyond breakers.
-Heat exchanger inspection.
-New equipment installation.
-Poor air quality, persistent problems after basic maintenance.
-
-**HVAC lifespan:** Furnace 15-20 years. AC 15-20 years. Heat pump 15 years. Well-maintained systems last longer.
-
-Sources: ENERGY STAR (energystar.gov), ACCA (Air Conditioning Contractors of America), Department of Energy HVAC guides (energy.gov), ASHRAE standards summaries
+---
+watermark: ORIRO
+disable-model-invocation: true
+name: trades-hvac
+provider: ORIRO.ai
+copyright: Copyright (c) 2026 ORIRO.ai
+description: >
+
+  HVAC — heating, cooling, ventilation principles, maintenance, troubleshooting, and energy efficiency.
+
+
+
+
+  Sources: USDA, OSHA, trade association guidelines, professional kitchen standards.
+---
+
+# HVAC
+
+## How heating and cooling systems work
+
+### Forced-air systems (most common in US)
+
+**Furnace:** Burns gas (or propane, oil) to heat air. Blower distributes heated air through ducts.
+**Air conditioning (split system):** Refrigerant cycles between indoor unit (absorbs heat from indoor air) and outdoor unit (releases heat outside). Cooling is heat removal, not cold creation.
+**Heat pump:** Refrigerant-based like AC but can reverse cycle to provide heat. More efficient than electric resistance heat. Types: Air-source (outdoor unit), Ground-source (geothermal — higher efficiency, higher cost).
+**Ductwork:** Delivers conditioned air. Return ducts bring air back. Leaky ducts: 20-30% efficiency loss common.
+
+### Efficiency ratings
+
+**Furnace:** AFUE (Annual Fuel Utilization Efficiency). 80%+ = good; 95%+ = high-efficiency condensing.
+**Air conditioner:** SEER2 (Seasonal Energy Efficiency Ratio). 14-16 = standard; 18+ = high-efficiency.
+**Heat pump:** HSPF2 (heating), SEER2 (cooling). Higher = more efficient.
+
+## Maintenance schedule
+
+**Monthly:** Check and replace air filter. A clogged filter: Reduces airflow → strain on system → higher energy use → shorter equipment life. MERV 8-13 filters balance filtration with airflow.
+
+**Spring (before cooling season):**
+Clean AC condenser coils (outdoor unit). Clear debris around outdoor unit (12" clearance).
+Check refrigerant charge (professional). Schedule professional tune-up for AC.
+
+**Fall (before heating season):**
+Schedule professional furnace tune-up. Replace filter.
+Test carbon monoxide detectors.
+Check heat exchanger for cracks (professional — cracked heat exchanger = CO hazard).
+
+**Annual:** Professional HVAC inspection and tune-up. Clean evaporator coil (indoor) as needed.
+
+## Troubleshooting common problems
+
+**No cooling/heating:**
+Check thermostat settings and batteries.
+Check circuit breaker (AC on dedicated circuit; high-voltage contactor in outdoor unit can trip).
+Check air filter (clogged filter causes freeze-up).
+Check outdoor unit — is it running?
+
+**Poor airflow:**
+Dirty filter (#1 cause).
+Blocked/closed supply or return vents.
+Damaged ductwork.
+
+**Water around indoor unit:**
+Condensate drain clogged. Flush with bleach water solution.
+Frozen evaporator coil thawing (caused by: dirty filter, low refrigerant, restricted airflow).
+
+**High energy bills:**
+Air filter. Leaky ducts. Refrigerant charge. Equipment aging. Poor insulation/sealing.
+
+## When to call a professional
+
+Refrigerant handling: Illegal without EPA certification.
+Gas line work: Always.
+Electrical within the unit beyond breakers.
+Heat exchanger inspection.
+New equipment installation.
+Poor air quality, persistent problems after basic maintenance.
+
+**HVAC lifespan:** Furnace 15-20 years. AC 15-20 years. Heat pump 15 years. Well-maintained systems last longer.
+
+Sources: ENERGY STAR (energystar.gov), ACCA (Air Conditioning Contractors of America), Department of Energy HVAC guides (energy.gov), ASHRAE standards summaries

package/skills/trades/trades-landscaping/LICENSE

@@ -1,21 +1,21 @@
-MIT License
-
-Copyright (c) 2026 ORIRO.ai
-
-Permission is hereby granted, free of charge, to any person obtaining a copy
-of this software and associated documentation files (the "Software"), to deal
-in the Software without restriction, including without limitation the rights
-to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
-copies of the Software, and to permit persons to whom the Software is
-furnished to do so, subject to the following conditions:
-
-The above copyright notice and this permission notice shall be included in all
-copies or substantial portions of the Software.
-
-THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
-AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
-OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
-SOFTWARE.
+MIT License
+
+Copyright (c) 2026 ORIRO.ai
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.

package/skills/trades/trades-landscaping/SKILL.md

@@ -1,60 +1,60 @@
----
-watermark: ORIRO
-disable-model-invocation: true
-name: trades-landscaping
-provider: ORIRO.ai
-copyright: Copyright (c) 2026 ORIRO.ai
-description: >
-  Landscaping and horticulture — plant selection, soil science, irrigation,
-  landscape design, hardscaping, and seasonal maintenance. Sources: USDA Plant
-  Hardiness Zones (free), RHS (rhs.org.uk — free guides).
----
-
-# Landscaping and Horticulture
-
-## Soil science fundamentals
-
-**Soil texture:** Sand (large particles, drains fast), silt (medium), clay (small, retains water).
-**Loam:** Ideal mix — 40% sand, 40% silt, 20% clay.
-**Soil pH:** 6.0-7.0 optimal for most plants. Below 6 = acidic. Above 7 = alkaline.
-**Amendments:** Lime raises pH. Sulfur lowers pH. Compost improves structure.
-**Soil test:** $15-30 through county extension. Test before major planting.
-
-## Plant hardiness zones
-
-**USDA Hardiness Zones:** 1-13. Based on minimum winter temperature.
-Zone 5 (-20°F minimum), Zone 6 (-10°F), Zone 7 (0°F), Zone 8 (10°F), Zone 9 (20°F).
-Match plants to zone. Northeast US = Zones 4-6. Southeast US = 7-9. UK = 6-8.
-
-## Plant selection principles
-
-**Right plant, right place:** Match water/sun/soil needs to site conditions.
-**Native plants:** Lower maintenance, local wildlife support, water-wise.
-**Succession planting:** Plan for bloom times across seasons.
-**Foundation planting:** Rule: Mature plant width + 2 feet clearance from structure.
-
-## Irrigation
-
-**Drip irrigation:** 90% efficient. Delivers water to root zone.
-**Overhead sprinklers:** 50-70% efficient. Water in morning to reduce disease.
-**Watering rule:** Deep, infrequent watering promotes deep roots.
-Established trees/shrubs: Weekly during dry periods.
-New plantings: Every 2-3 days for first growing season.
-
-## Landscape design basics
-
-**Focal point:** Every view needs a focal point — specimen tree, sculpture, fountain.
-**Balance:** Symmetrical (formal) or asymmetrical (naturalistic).
-**Proportion:** Plant mature size in relation to house and other plants.
-**Rhythm:** Repetition of species or color throughout planting.
-**Hardscape ratio:** Generally 60% soft (plants), 40% hard (stone, wood, concrete).
-
-## Seasonal maintenance
-
-**Spring:** Fertilize lawns, divide perennials, plant warm-season annuals after frost.
-**Summer:** Irrigation management, deadheading, pest scouting.
-**Fall:** Plant trees/shrubs (root establishment without heat stress), bulb planting, winterize irrigation.
-**Winter:** Pruning dormant trees/shrubs (NOT spring-blooming), planning.
-
-Sources: USDA Plant Hardiness Zone Map (free, public domain), RHS (rhs.org.uk — free),
-University Extension Services (free local guides)
+---
+watermark: ORIRO
+disable-model-invocation: true
+name: trades-landscaping
+provider: ORIRO.ai
+copyright: Copyright (c) 2026 ORIRO.ai
+description: >
+  Landscaping and horticulture — plant selection, soil science, irrigation,
+  landscape design, hardscaping, and seasonal maintenance. Sources: USDA Plant
+  Hardiness Zones (free), RHS (rhs.org.uk — free guides).
+---
+
+# Landscaping and Horticulture
+
+## Soil science fundamentals
+
+**Soil texture:** Sand (large particles, drains fast), silt (medium), clay (small, retains water).
+**Loam:** Ideal mix — 40% sand, 40% silt, 20% clay.
+**Soil pH:** 6.0-7.0 optimal for most plants. Below 6 = acidic. Above 7 = alkaline.
+**Amendments:** Lime raises pH. Sulfur lowers pH. Compost improves structure.
+**Soil test:** $15-30 through county extension. Test before major planting.
+
+## Plant hardiness zones
+
+**USDA Hardiness Zones:** 1-13. Based on minimum winter temperature.
+Zone 5 (-20°F minimum), Zone 6 (-10°F), Zone 7 (0°F), Zone 8 (10°F), Zone 9 (20°F).
+Match plants to zone. Northeast US = Zones 4-6. Southeast US = 7-9. UK = 6-8.
+
+## Plant selection principles
+
+**Right plant, right place:** Match water/sun/soil needs to site conditions.
+**Native plants:** Lower maintenance, local wildlife support, water-wise.
+**Succession planting:** Plan for bloom times across seasons.
+**Foundation planting:** Rule: Mature plant width + 2 feet clearance from structure.
+
+## Irrigation
+
+**Drip irrigation:** 90% efficient. Delivers water to root zone.
+**Overhead sprinklers:** 50-70% efficient. Water in morning to reduce disease.
+**Watering rule:** Deep, infrequent watering promotes deep roots.
+Established trees/shrubs: Weekly during dry periods.
+New plantings: Every 2-3 days for first growing season.
+
+## Landscape design basics
+
+**Focal point:** Every view needs a focal point — specimen tree, sculpture, fountain.
+**Balance:** Symmetrical (formal) or asymmetrical (naturalistic).
+**Proportion:** Plant mature size in relation to house and other plants.
+**Rhythm:** Repetition of species or color throughout planting.
+**Hardscape ratio:** Generally 60% soft (plants), 40% hard (stone, wood, concrete).
+
+## Seasonal maintenance
+
+**Spring:** Fertilize lawns, divide perennials, plant warm-season annuals after frost.
+**Summer:** Irrigation management, deadheading, pest scouting.
+**Fall:** Plant trees/shrubs (root establishment without heat stress), bulb planting, winterize irrigation.
+**Winter:** Pruning dormant trees/shrubs (NOT spring-blooming), planning.
+
+Sources: USDA Plant Hardiness Zone Map (free, public domain), RHS (rhs.org.uk — free),
+University Extension Services (free local guides)

package/skills/trades/trades-metalworking/LICENSE

@@ -1,21 +1,21 @@
-MIT License
-
-Copyright (c) 2026 ORIRO.ai
-
-Permission is hereby granted, free of charge, to any person obtaining a copy
-of this software and associated documentation files (the "Software"), to deal
-in the Software without restriction, including without limitation the rights
-to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
-copies of the Software, and to permit persons to whom the Software is
-furnished to do so, subject to the following conditions:
-
-The above copyright notice and this permission notice shall be included in all
-copies or substantial portions of the Software.
-
-THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
-AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
-OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
-SOFTWARE.
+MIT License
+
+Copyright (c) 2026 ORIRO.ai
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.

package/skills/trades/trades-metalworking/SKILL.md

@@ -1,64 +1,64 @@
----
-watermark: ORIRO
-disable-model-invocation: true
-name: trades-metalworking
-provider: ORIRO.ai
-copyright: Copyright (c) 2026 ORIRO.ai
-description: >
-  Metalworking — welding, machining, metal properties, heat treatment, and
-  fabrication techniques for hobbyists and professionals. Sources: AWS (American
-  Welding Society) fundamentals (free), MIT OCW 2.008 (CC-BY).
----
-
-# Metalworking
-
-## Welding processes
-
-### MIG (GMAW)
-
-Most beginner-friendly. Wire-feed electrode. Continuous arc.
-**Settings:** Wire speed + voltage. Hotter = more voltage, faster = more wire.
-Gas: 75% Argon/25% CO₂ (C25) for steel. 100% Argon for aluminum.
-Good for: Mild steel, sheet metal, automotive repair.
-
-### TIG (GTAW)
-
-Most precise. Separate filler rod fed by hand. Non-consumable tungsten electrode.
-**Applications:** Aluminum, stainless steel, exotic alloys.
-AC for aluminum, DC- for steel/stainless.
-Pedal controls heat. Highest quality welds.
-
-### Stick (SMAW)
-
-Most portable. No gas required. Works on dirty/rusty metal.
-Electrode types: 6013 (easy, general), 7018 (structural), 6011 (all-position).
-**Good for:** Field repairs, thick steel, construction.
-
-### Welding safety
-
-Auto-darkening helmet minimum shade 10 for MIG, 11-12 for TIG.
-Never weld galvanized metal without respirator (zinc fumes toxic).
-
-## Metal properties
-
-**Low carbon steel (A36, 1018):** Easy to weld, machine, and form. Most common.
-**Stainless steel (304, 316):** Corrosion resistant. Chrome 18%, Nickel 8%.
-**Aluminum (6061-T6):** Lightweight, corrosion resistant. Tricky to weld.
-**Tool steel (D2, O1):** High hardness for cutting tools. Requires careful heat treatment.
-
-## Heat treatment
-
-**Annealing:** Heat to critical temperature, slow cool. Softens metal, relieves stress.
-**Hardening:** Heat steel + quench (water/oil). Increases hardness.
-**Tempering:** After hardening, reheat to lower temperature. Reduces brittleness.
-Steel tempering colors: Pale yellow (~425°F), Straw (~450°F), Purple (~510°F), Blue (~570°F).
-
-## Basic machining
-
-**Lathe:** Rotates workpiece. Turn, face, bore, thread.
-**Mill:** Rotates cutting tool. Slots, pockets, surfaces.
-**Drill press:** Controlled drilling. Use cutting speed chart by material.
-**Speeds and feeds:** Higher for soft metals, lower for hard. Tool life vs material removal rate.
-
-Sources: AWS (americanweldingsociety.org — free fundamentals), MIT OCW 2.008 (CC-BY),
-Lincoln Electric welding guides (free)
+---
+watermark: ORIRO
+disable-model-invocation: true
+name: trades-metalworking
+provider: ORIRO.ai
+copyright: Copyright (c) 2026 ORIRO.ai
+description: >
+  Metalworking — welding, machining, metal properties, heat treatment, and
+  fabrication techniques for hobbyists and professionals. Sources: AWS (American
+  Welding Society) fundamentals (free), MIT OCW 2.008 (CC-BY).
+---
+
+# Metalworking
+
+## Welding processes
+
+### MIG (GMAW)
+
+Most beginner-friendly. Wire-feed electrode. Continuous arc.
+**Settings:** Wire speed + voltage. Hotter = more voltage, faster = more wire.
+Gas: 75% Argon/25% CO₂ (C25) for steel. 100% Argon for aluminum.
+Good for: Mild steel, sheet metal, automotive repair.
+
+### TIG (GTAW)
+
+Most precise. Separate filler rod fed by hand. Non-consumable tungsten electrode.
+**Applications:** Aluminum, stainless steel, exotic alloys.
+AC for aluminum, DC- for steel/stainless.
+Pedal controls heat. Highest quality welds.
+
+### Stick (SMAW)
+
+Most portable. No gas required. Works on dirty/rusty metal.
+Electrode types: 6013 (easy, general), 7018 (structural), 6011 (all-position).
+**Good for:** Field repairs, thick steel, construction.
+
+### Welding safety
+
+Auto-darkening helmet minimum shade 10 for MIG, 11-12 for TIG.
+Never weld galvanized metal without respirator (zinc fumes toxic).
+
+## Metal properties
+
+**Low carbon steel (A36, 1018):** Easy to weld, machine, and form. Most common.
+**Stainless steel (304, 316):** Corrosion resistant. Chrome 18%, Nickel 8%.
+**Aluminum (6061-T6):** Lightweight, corrosion resistant. Tricky to weld.
+**Tool steel (D2, O1):** High hardness for cutting tools. Requires careful heat treatment.
+
+## Heat treatment
+
+**Annealing:** Heat to critical temperature, slow cool. Softens metal, relieves stress.
+**Hardening:** Heat steel + quench (water/oil). Increases hardness.
+**Tempering:** After hardening, reheat to lower temperature. Reduces brittleness.
+Steel tempering colors: Pale yellow (~425°F), Straw (~450°F), Purple (~510°F), Blue (~570°F).
+
+## Basic machining
+
+**Lathe:** Rotates workpiece. Turn, face, bore, thread.
+**Mill:** Rotates cutting tool. Slots, pockets, surfaces.
+**Drill press:** Controlled drilling. Use cutting speed chart by material.
+**Speeds and feeds:** Higher for soft metals, lower for hard. Tool life vs material removal rate.
+
+Sources: AWS (americanweldingsociety.org — free fundamentals), MIT OCW 2.008 (CC-BY),
+Lincoln Electric welding guides (free)

package/skills/trades/trades-painting/LICENSE

@@ -1,21 +1,21 @@
-MIT License
-
-Copyright (c) 2026 ORIRO.ai
-
-Permission is hereby granted, free of charge, to any person obtaining a copy
-of this software and associated documentation files (the "Software"), to deal
-in the Software without restriction, including without limitation the rights
-to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
-copies of the Software, and to permit persons to whom the Software is
-furnished to do so, subject to the following conditions:
-
-The above copyright notice and this permission notice shall be included in all
-copies or substantial portions of the Software.
-
-THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
-AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
-OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
-SOFTWARE.
+MIT License
+
+Copyright (c) 2026 ORIRO.ai
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.