cgse 2024.7.0__py3-none-any.whl → 2025.0.2__py3-none-any.whl

egse/aeu/aeu_psu.yaml

@@ -1,204 +0,0 @@
-BaseClass:
-    egse.aeu.PSUInterface
-
-ProxyClass:
-    egse.aeu.PSUProxy
-
-ControlServerClass:
-    egse.aeu.PSUControlServer
-
-ControlServer:
-    egse.aeu.aeu_cs
-
-#UserInterface:
-#    egse.aeu.aeu_ui
-
-Commands:
-
-    # Each of these groups is parsed and used on both the server and the client side.
-    #
-    # The group name (e.g. is_simulator) will be monkey patched in the Proxy class for the device
-    # or service.
-    #
-    # The other field are:
-    #   description:   Used by the doc_string method to generate a help string
-    #   cmd:           Command string that will eventually be send to the hardware controller for
-    #                  the device. This cmd string is also used at the client side to parse and
-    #                  validate the arguments.
-    #   device_method: The name of the method to be called on the device class.
-    #                  These should all be defined by the interface class for the device, i.e.
-    #                  AEUInterface in this case.
-    #                  When the device_method is the same as the group name, it can be omitted.
-    #   response:      The name of the method to be called from the device protocol.
-    #                  This method should exist in the subclass of the CommandProtocol base class,
-    #                  i.e. in this case it will be the AEUProtocol class.
-    #                  The default (when no response is given) is 'handle_device_method'.
-
-    # Definition of the the DeviceInterface
-
-    is_simulator:
-        description: Ask if the connected class is a simulator instead of the real device Controller class.
-        returns: bool | True if the far-end is a simulator instead of the real hardware
-
-    is_connected:
-        description: Check if the device hardware controller is connected.
-
-    connect:
-        description: Connect the device hardware controller.
-
-    reconnect:
-        description: Reconnect the device hardware controller.  This command will force a disconnect and then try to
-                     re-connect to the controller.
-
-    disconnect:
-        description: Disconnect from the device hardware controller. This command will be send to the Control Server
-                     which will then disconnect from the hardware controller.
-                     This command does not affect the ZeroMQ connection of the Proxy to the control server. Use the
-                     service command `disconnect_cs()` to disconnect from the control server.
-
-    # PSU commands
-
-    get_id:
-        description:    Return the model name, serial number, and firmware version of the PMX.
-        cmd:            "*IDN?"
-
-    reset:
-        description:    Reset the panel settings, clear alarms, abort the trigger sub-system operation, clear the
-                        OPC bit (bit0) of the status event register.
-        cmd:            "*RST"
-
-    test:
-        description:    Execute a self-test.
-        cmd:            "*TST"
-
-    get_error_info:
-        description:    Read the oldest error information the error queue.  The error queue can store up to 16 errors.
-                        Use the clear_psu command to clear the error queue.
-        cmd:            "SYST:ERR?"
-
-    clear:
-        description:    Clear all event registers, including the status byte, event status, and error queue.
-        cmd:            "*CLS"
-
-    set_channel:
-        description:    Specify the channel to configure (should be 1).
-        cmd:            "INST {}"
-
-    get_channel:
-        description:    Return the channel to configure (should be 1).
-        cmd:            "INST?"
-
-    get_channel_list:
-        description:    Return the list of channels that can be configured with the set_channel command.
-        cmd:            "INST:CAT?"
-
-    get_channel_info:
-        description:    Return the information of the channel currently being controlled.
-        cmd:            "INST:INFO?"
-
-    get_current:
-        description:    Return the measured value of the current [A].
-        cmd:            "MEAS:CURR?"
-
-    get_voltage:
-        description:    Return the measured value of the voltage [V].
-        cmd:            "MEAS:VOLT?"
-
-    recall_memory:
-        description:    Recall the settings (current, voltage, OCP (Over-Current Protection), and OVP (Over-Voltage
-                        Protection)) stored in the pre-set memory (1 for memory A, 2 for memory B, 3 for memory C).
-                        When recalling a pre-set memory when the output is turned on, the setting stored in the
-                        memory will be applied immediately.
-        cmd:            "MEM:REC {}"
-
-    conf_settings:
-        description:    Set whether or not to check the content saved in the pre-set memory (current, voltage, OCP
-                        (Over-Current Protection), and OVP (Over-Voltage Protection)), when recalling it from the
-                        control panel (1 to confirm the settings, 0 to reject the settings).  When recalling the memory
-                        with the recall_psu_memory command, the settings stored in the pre-set memory will be recalled
-                        immediately.
-        cmd:            "MEM:REC:CONF {}"
-
-    get_memory_config:
-        description:    Query whether or not to check the content (current, voltage, OCP (Over-Current Protection), and
-                        OVP (Over-Voltage Protection)) saved in the pre-set memory when recalling them from the control
-                        panel.
-        cmd:            "MEM:REC:CONF?"
-
-    get_memory_setting:
-        description:    Return the current, voltage, OCP (Over-Current Protection), and OVP (Over-Voltage Protection)
-                        as stored in the pre-set memory (1 for memory A, 2 for memory B, 3 for memory C).
-        cmd:            "MEM:REC:PREV? {}"
-
-    save_memory:
-        description:    Save to the pre-set memory (1 for memory A, 2 for memory B, 3 for memory C).  The current,
-                        voltage, OCP (Over-Current Protection), and OVP (Over-Voltage Protection) are saved in the
-                        pre-set memory.
-        cmd:            "MEM:SAVE {}"
-
-    set_output_status:
-        description:    Set the output status and type (ON/OFF).  This command is invalid when a protection function
-                        is activated.  The settings are reset to default with the reset_psu command.
-        cmd:            "OUTP {}"
-
-    get_output_status:
-        description:    Return the output status and type (ON/OFF).
-        cmd:            "OUTP?"
-
-    set_current:
-        description:    Set the current to the given value [A].  This is invalid when the PMX is configured such that
-                        constant current is controlled externally.  The settings are set to the default values with the
-                        reset_pmu command.
-        cmd:            "CURR {}"
-
-    get_current_config:
-        description:    Return the actual current configuration [A].
-        cmd:            "CURR?"
-
-    set_ocp:
-        description:    Set the Over-Current Protection (OCP) value [A].  The settings are set to the default values
-                        with the reset_pmu command.
-        cmd:            "CURR:PROT {}"
-
-    get_ocp:
-        description:    Return the Over-Current Protection (OCP) value [A].
-        cmd:            "CURR:PROT?"
-
-    set_voltage:
-        description:    Set the voltage to the given value [V].  This is invalid when the PMX is configured such that
-                        constant voltage is controlled externally.  The settigns are set to the default values with the
-                        reset_pmu command.
-        cmd:            "VOLT {}"
-
-    get_voltage_config:
-        description:    Return the actual voltage configuration [V].
-        cmd:            "VOLT?"
-
-    set_ovp:
-        description:    Set the Over-Voltage Protection (OVP) value [V].  The settings are set to the default values
-                        with the reset_pmu command.
-        cmd:            "VOLT:PROT {}"
-
-    get_ovp:
-        description:    Return the Over-Voltage Protection (OVP) value [A].
-        cmd:            "VOLT:PROT?"
-
-    set_priority_mode:
-        description:    Set the operation mode to be prioritised when the output is turned on.  Should be CC for
-                        Constant Current, CV for Constant Voltage.
-        cmd:            "SYST:CONF:STAR:PRI {}"
-
-    get_priority_mode:
-        description:    Return the operation mode to be prioritised when the output is turned on.  Should be CC for
-                        Constant Current, CV for Constant Voltage.
-        cmd:            "SYST:CONF:STAR:PRI?"
-
-    clear_alarms:
-        description:    Clear all alarms.
-        cmd:            "OUTP:PROT:CLE"
-
-    questionable_status_register:
-        description:    Query the status of the questionable status register.  A query does not clear the content of
-                        the register.  This command is usefule to get the events and status during PMX operation (e.g.
-                        when the PSU detects and OVP or OCP).
-        cmd:            "STAT:QUES:COND?"