esphome 2025.5.2__py3-none-any.whl → 2025.6.0__py3-none-any.whl

esphome/components/sps30/sps30.cpp

@@ -22,7 +22,7 @@ static const size_t SERIAL_NUMBER_LENGTH = 8;
 static const uint8_t MAX_SKIPPED_DATA_CYCLES_BEFORE_ERROR = 5;
 
 void SPS30Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up sps30...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->write_command(SPS30_CMD_SOFT_RESET);
   /// Deferred Sensor initialization
   this->set_timeout(500, [this]() {
@@ -73,10 +73,10 @@ void SPS30Component::dump_config() {
   if (this->is_failed()) {
     switch (this->error_code_) {
       case COMMUNICATION_FAILED:
-        ESP_LOGW(TAG, "Communication failed! Is the sensor connected?");
+        ESP_LOGW(TAG, ESP_LOG_MSG_COMM_FAIL);
         break;
       case MEASUREMENT_INIT_FAILED:
-        ESP_LOGW(TAG, "Measurement Initialization failed!");
+        ESP_LOGW(TAG, "Measurement Initialization failed");
         break;
       case SERIAL_NUMBER_REQUEST_FAILED:
         ESP_LOGW(TAG, "Unable to request sensor serial number");
@@ -91,14 +91,15 @@ void SPS30Component::dump_config() {
         ESP_LOGW(TAG, "Unable to read sensor firmware version");
         break;
       default:
-        ESP_LOGW(TAG, "Unknown setup error!");
+        ESP_LOGW(TAG, "Unknown setup error");
         break;
     }
   }
   LOG_UPDATE_INTERVAL(this);
-  ESP_LOGCONFIG(TAG, "  Serial Number: '%s'", this->serial_number_);
-  ESP_LOGCONFIG(TAG, "  Firmware version v%0d.%0d", (raw_firmware_version_ >> 8),
-                uint16_t(raw_firmware_version_ & 0xFF));
+  ESP_LOGCONFIG(TAG,
+                "  Serial Number: '%s'\n"
+                "  Firmware version v%0d.%0d",
+                this->serial_number_, (raw_firmware_version_ >> 8), uint16_t(raw_firmware_version_ & 0xFF));
   LOG_SENSOR("  ", "PM1.0 Weight Concentration", this->pm_1_0_sensor_);
   LOG_SENSOR("  ", "PM2.5 Weight Concentration", this->pm_2_5_sensor_);
   LOG_SENSOR("  ", "PM4 Weight Concentration", this->pm_4_0_sensor_);
@@ -113,18 +114,18 @@ void SPS30Component::dump_config() {
 void SPS30Component::update() {
   /// Check if warning flag active (sensor reconnected?)
   if (this->status_has_warning()) {
-    ESP_LOGD(TAG, "Trying to reconnect the sensor...");
+    ESP_LOGD(TAG, "Trying to reconnect");
     if (this->write_command(SPS30_CMD_SOFT_RESET)) {
-      ESP_LOGD(TAG, "Sensor has soft-reset successfully. Waiting for reconnection in 500ms...");
+      ESP_LOGD(TAG, "Soft-reset successful. Waiting for reconnection in 500 ms");
       this->set_timeout(500, [this]() {
         this->start_continuous_measurement_();
         /// Sensor restarted and reading attempt made next cycle
         this->status_clear_warning();
         this->skipped_data_read_cycles_ = 0;
-        ESP_LOGD(TAG, "Sensor reconnected successfully. Resuming continuous measurement!");
+        ESP_LOGD(TAG, "Reconnect successful. Resuming continuous measurement");
       });
     } else {
-      ESP_LOGD(TAG, "Sensor soft-reset failed. Is the sensor offline?");
+      ESP_LOGD(TAG, "Soft-reset failed");
     }
     return;
   }
@@ -136,19 +137,19 @@ void SPS30Component::update() {
 
   uint16_t raw_read_status;
   if (!this->read_data(&raw_read_status, 1) || raw_read_status == 0x00) {
-    ESP_LOGD(TAG, "Sensor measurement not ready yet.");
+    ESP_LOGD(TAG, "Not ready yet");
     this->skipped_data_read_cycles_++;
     /// The following logic is required to address the cases when a sensor is quickly replaced before it's marked
     /// as failed so that new sensor is eventually forced to be reinitialized for continuous measurement.
     if (this->skipped_data_read_cycles_ > MAX_SKIPPED_DATA_CYCLES_BEFORE_ERROR) {
-      ESP_LOGD(TAG, "Sensor exceeded max allowed attempts. Sensor communication will be reinitialized.");
+      ESP_LOGD(TAG, "Exceeded max allowed attempts; communication will be reinitialized");
       this->status_set_warning();
     }
     return;
   }
 
   if (!this->write_command(SPS30_CMD_READ_MEASUREMENT)) {
-    ESP_LOGW(TAG, "Error reading measurement status!");
+    ESP_LOGW(TAG, "Error reading status");
     this->status_set_warning();
     return;
   }
@@ -156,7 +157,7 @@ void SPS30Component::update() {
   this->set_timeout(50, [this]() {
     uint16_t raw_data[20];
     if (!this->read_data(raw_data, 20)) {
-      ESP_LOGW(TAG, "Error reading measurement data!");
+      ESP_LOGW(TAG, "Error reading data");
       this->status_set_warning();
       return;
     }

esphome/components/ssd1306_base/ssd1306_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1306_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1306_base {

esphome/components/ssd1306_i2c/ssd1306_i2c.cpp

@@ -7,7 +7,7 @@ namespace ssd1306_i2c {
 static const char *const TAG = "ssd1306_i2c";
 
 void I2CSSD1306::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up I2C SSD1306...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->init_reset_();
 
   auto err = this->write(nullptr, 0);
@@ -24,16 +24,19 @@ void I2CSSD1306::dump_config() {
   LOG_I2C_DEVICE(this);
   ESP_LOGCONFIG(TAG, "  Model: %s", this->model_str_());
   LOG_PIN("  Reset Pin: ", this->reset_pin_);
-  ESP_LOGCONFIG(TAG, "  External VCC: %s", YESNO(this->external_vcc_));
-  ESP_LOGCONFIG(TAG, "  Flip X: %s", YESNO(this->flip_x_));
-  ESP_LOGCONFIG(TAG, "  Flip Y: %s", YESNO(this->flip_y_));
-  ESP_LOGCONFIG(TAG, "  Offset X: %d", this->offset_x_);
-  ESP_LOGCONFIG(TAG, "  Offset Y: %d", this->offset_y_);
-  ESP_LOGCONFIG(TAG, "  Inverted Color: %s", YESNO(this->invert_));
+  ESP_LOGCONFIG(TAG,
+                "  External VCC: %s\n"
+                "  Flip X: %s\n"
+                "  Flip Y: %s\n"
+                "  Offset X: %d\n"
+                "  Offset Y: %d\n"
+                "  Inverted Color: %s",
+                YESNO(this->external_vcc_), YESNO(this->flip_x_), YESNO(this->flip_y_), this->offset_x_,
+                this->offset_y_, YESNO(this->invert_));
   LOG_UPDATE_INTERVAL(this);
 
   if (this->error_code_ == COMMUNICATION_FAILED) {
-    ESP_LOGE(TAG, "Communication with SSD1306 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
 }
 void I2CSSD1306::command(uint8_t value) { this->write_byte(0x00, value); }

esphome/components/ssd1306_spi/ssd1306_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1306_spi {
 static const char *const TAG = "ssd1306_spi";
 
 void SPISSD1306::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1306...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
 
@@ -21,12 +21,15 @@ void SPISSD1306::dump_config() {
   LOG_PIN("  CS Pin: ", this->cs_);
   LOG_PIN("  DC Pin: ", this->dc_pin_);
   LOG_PIN("  Reset Pin: ", this->reset_pin_);
-  ESP_LOGCONFIG(TAG, "  External VCC: %s", YESNO(this->external_vcc_));
-  ESP_LOGCONFIG(TAG, "  Flip X: %s", YESNO(this->flip_x_));
-  ESP_LOGCONFIG(TAG, "  Flip Y: %s", YESNO(this->flip_y_));
-  ESP_LOGCONFIG(TAG, "  Offset X: %d", this->offset_x_);
-  ESP_LOGCONFIG(TAG, "  Offset Y: %d", this->offset_y_);
-  ESP_LOGCONFIG(TAG, "  Inverted Color: %s", YESNO(this->invert_));
+  ESP_LOGCONFIG(TAG,
+                "  External VCC: %s\n"
+                "  Flip X: %s\n"
+                "  Flip Y: %s\n"
+                "  Offset X: %d\n"
+                "  Offset Y: %d\n"
+                "  Inverted Color: %s",
+                YESNO(this->external_vcc_), YESNO(this->flip_x_), YESNO(this->flip_y_), this->offset_x_,
+                this->offset_y_, YESNO(this->invert_));
   LOG_UPDATE_INTERVAL(this);
 }
 void SPISSD1306::command(uint8_t value) {

esphome/components/ssd1322_base/ssd1322_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1322_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1322_base {

esphome/components/ssd1322_spi/ssd1322_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1322_spi {
 static const char *const TAG = "ssd1322_spi";
 
 void SPISSD1322::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1322...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
   if (this->cs_)

esphome/components/ssd1325_base/ssd1325_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1325_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1325_base {

esphome/components/ssd1325_spi/ssd1325_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1325_spi {
 static const char *const TAG = "ssd1325_spi";
 
 void SPISSD1325::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1325...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
   if (this->cs_)

esphome/components/ssd1327_base/ssd1327_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1327_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1327_base {

esphome/components/ssd1327_i2c/ssd1327_i2c.cpp

@@ -7,7 +7,7 @@ namespace ssd1327_i2c {
 static const char *const TAG = "ssd1327_i2c";
 
 void I2CSSD1327::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up I2C SSD1327...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->init_reset_();
 
   auto err = this->write(nullptr, 0);
@@ -27,7 +27,7 @@ void I2CSSD1327::dump_config() {
   LOG_UPDATE_INTERVAL(this);
 
   if (this->error_code_ == COMMUNICATION_FAILED) {
-    ESP_LOGE(TAG, "Communication with SSD1327 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
 }
 void I2CSSD1327::command(uint8_t value) { this->write_byte(0x00, value); }

esphome/components/ssd1327_spi/ssd1327_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1327_spi {
 static const char *const TAG = "ssd1327_spi";
 
 void SPISSD1327::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1327...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
   if (this->cs_)

esphome/components/ssd1331_base/ssd1331_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1331_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1331_base {

esphome/components/ssd1331_spi/ssd1331_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1331_spi {
 static const char *const TAG = "ssd1331_spi";
 
 void SPISSD1331::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1331...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
   if (this->cs_)

esphome/components/ssd1351_base/ssd1351_base.cpp

@@ -1,6 +1,6 @@
 #include "ssd1351_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace ssd1351_base {

esphome/components/ssd1351_spi/ssd1351_spi.cpp

@@ -8,7 +8,7 @@ namespace ssd1351_spi {
 static const char *const TAG = "ssd1351_spi";
 
 void SPISSD1351::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI SSD1351...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();  // OUTPUT
   if (this->cs_)

esphome/components/st7567_base/st7567_base.cpp

@@ -1,6 +1,6 @@
 #include "st7567_base.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace st7567_base {
@@ -13,7 +13,7 @@ void ST7567::setup() {
 }
 
 void ST7567::display_init_() {
-  ESP_LOGD(TAG, "Initializing ST7567 display...");
+  ESP_LOGD(TAG, "Initializing display");
   this->display_init_registers_();
   this->clear();
   this->write_display_data();
@@ -42,7 +42,7 @@ void ST7567::display_init_registers_() {
 }
 
 void ST7567::display_sw_refresh_() {
-  ESP_LOGD(TAG, "Performing refresh sequence...");
+  ESP_LOGD(TAG, "Performing refresh sequence");
   this->command(ST7567_SW_REFRESH);
   this->display_init_registers_();
 }

esphome/components/st7567_i2c/st7567_i2c.cpp

@@ -7,7 +7,7 @@ namespace st7567_i2c {
 static const char *const TAG = "st7567_i2c";
 
 void I2CST7567::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up I2C ST7567 display...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->init_reset_();
 
   auto err = this->write(nullptr, 0);
@@ -24,13 +24,15 @@ void I2CST7567::dump_config() {
   LOG_I2C_DEVICE(this);
   ESP_LOGCONFIG(TAG, "  Model: %s", this->model_str_());
   LOG_PIN("  Reset Pin: ", this->reset_pin_);
-  ESP_LOGCONFIG(TAG, "  Mirror X: %s", YESNO(this->mirror_x_));
-  ESP_LOGCONFIG(TAG, "  Mirror Y: %s", YESNO(this->mirror_y_));
-  ESP_LOGCONFIG(TAG, "  Invert Colors: %s", YESNO(this->invert_colors_));
+  ESP_LOGCONFIG(TAG,
+                "  Mirror X: %s\n"
+                "  Mirror Y: %s\n"
+                "  Invert Colors: %s",
+                YESNO(this->mirror_x_), YESNO(this->mirror_y_), YESNO(this->invert_colors_));
   LOG_UPDATE_INTERVAL(this);
 
   if (this->error_code_ == COMMUNICATION_FAILED) {
-    ESP_LOGE(TAG, "Communication with I2C ST7567 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
 }
 

esphome/components/st7567_spi/st7567_spi.cpp

@@ -7,7 +7,7 @@ namespace st7567_spi {
 static const char *const TAG = "st7567_spi";
 
 void SPIST7567::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI ST7567 display...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   this->dc_pin_->setup();
   if (this->cs_)

esphome/components/st7701s/st7701s.cpp

@@ -181,8 +181,10 @@ void ST7701S::write_init_sequence_() {
 
 void ST7701S::dump_config() {
   ESP_LOGCONFIG("", "ST7701S RGB LCD");
-  ESP_LOGCONFIG(TAG, "  Height: %u", this->height_);
-  ESP_LOGCONFIG(TAG, "  Width: %u", this->width_);
+  ESP_LOGCONFIG(TAG,
+                "  Height: %u\n"
+                "  Width: %u",
+                this->height_, this->width_);
   LOG_PIN("  CS Pin: ", this->cs_);
   LOG_PIN("  DC Pin: ", this->dc_pin_);
   LOG_PIN("  DE Pin: ", this->de_pin_);

esphome/components/st7735/st7735.cpp

@@ -1,7 +1,7 @@
 #include "st7735.h"
-#include "esphome/core/log.h"
-#include "esphome/core/helpers.h"
 #include "esphome/core/hal.h"
+#include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace st7735 {
@@ -233,7 +233,7 @@ ST7735::ST7735(ST7735Model model, int width, int height, int colstart, int rowst
       height_(height) {}
 
 void ST7735::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up ST7735...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
 
   this->dc_pin_->setup();  // OUTPUT

esphome/components/st7789v/st7789v.cpp

@@ -8,7 +8,7 @@ static const char *const TAG = "st7789v";
 static const size_t TEMP_BUFFER_SIZE = 128;
 
 void ST7789V::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up SPI ST7789V...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 #ifdef USE_POWER_SUPPLY
   this->power_.request();
   // the PowerSupply component takes care of post turn-on delay
@@ -122,12 +122,15 @@ void ST7789V::setup() {
 
 void ST7789V::dump_config() {
   LOG_DISPLAY("", "SPI ST7789V", this);
-  ESP_LOGCONFIG(TAG, "  Model: %s", this->model_str_);
-  ESP_LOGCONFIG(TAG, "  Height: %u", this->height_);
-  ESP_LOGCONFIG(TAG, "  Width: %u", this->width_);
-  ESP_LOGCONFIG(TAG, "  Height Offset: %u", this->offset_height_);
-  ESP_LOGCONFIG(TAG, "  Width Offset: %u", this->offset_width_);
-  ESP_LOGCONFIG(TAG, "  8-bit color mode: %s", YESNO(this->eightbitcolor_));
+  ESP_LOGCONFIG(TAG,
+                "  Model: %s\n"
+                "  Height: %u\n"
+                "  Width: %u\n"
+                "  Height Offset: %u\n"
+                "  Width Offset: %u\n"
+                "  8-bit color mode: %s",
+                this->model_str_, this->height_, this->width_, this->offset_height_, this->offset_width_,
+                YESNO(this->eightbitcolor_));
   LOG_PIN("  CS Pin: ", this->cs_);
   LOG_PIN("  DC Pin: ", this->dc_pin_);
   LOG_PIN("  Reset Pin: ", this->reset_pin_);

esphome/components/st7920/st7920.cpp

@@ -32,7 +32,7 @@ static const uint8_t LCD_LINE2 = 0x88;
 static const uint8_t LCD_LINE3 = 0x98;
 
 void ST7920::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up ST7920...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->dump_config();
   this->spi_setup();
   this->init_internal_(this->get_buffer_length_());
@@ -95,8 +95,10 @@ void ST7920::fill(Color color) { memset(this->buffer_, color.is_on() ? 0xFF : 0x
 void ST7920::dump_config() {
   LOG_DISPLAY("", "ST7920", this);
   LOG_PIN("  CS Pin: ", this->cs_);
-  ESP_LOGCONFIG(TAG, "  Height: %d", this->height_);
-  ESP_LOGCONFIG(TAG, "  Width: %d", this->width_);
+  ESP_LOGCONFIG(TAG,
+                "  Height: %d\n"
+                "  Width: %d",
+                this->height_, this->width_);
 }
 
 float ST7920::get_setup_priority() const { return setup_priority::PROCESSOR; }
@@ -129,7 +131,7 @@ void HOT ST7920::draw_absolute_pixel_internal(int x, int y, Color color) {
 }
 
 void ST7920::display_init_() {
-  ESP_LOGD(TAG, "Initializing display...");
+  ESP_LOGD(TAG, "Initializing display");
   this->command_(LCD_BASIC);      // 8bit mode
   this->command_(LCD_BASIC);      // 8bit mode
   this->command_(LCD_CLS);        // clear screen

esphome/components/statsd/statsd.cpp

@@ -38,17 +38,21 @@ StatsdComponent::~StatsdComponent() {
 }
 
 void StatsdComponent::dump_config() {
-  ESP_LOGCONFIG(TAG, "statsD:");
-  ESP_LOGCONFIG(TAG, "  host: %s", this->host_);
-  ESP_LOGCONFIG(TAG, "  port: %d", this->port_);
+  ESP_LOGCONFIG(TAG,
+                "statsD:\n"
+                "  host: %s\n"
+                "  port: %d",
+                this->host_, this->port_);
   if (this->prefix_) {
     ESP_LOGCONFIG(TAG, "  prefix: %s", this->prefix_);
   }
 
   ESP_LOGCONFIG(TAG, "  metrics:");
   for (sensors_t s : this->sensors_) {
-    ESP_LOGCONFIG(TAG, "    - name: %s", s.name);
-    ESP_LOGCONFIG(TAG, "      type: %d", s.type);
+    ESP_LOGCONFIG(TAG,
+                  "    - name: %s\n"
+                  "      type: %d",
+                  s.name, s.type);
   }
 }
 

esphome/components/status_led/light/status_led_light.cpp

@@ -9,10 +9,10 @@ namespace status_led {
 static const char *const TAG = "status_led";
 
 void StatusLEDLightOutput::loop() {
-  uint32_t new_state = App.get_app_state() & STATUS_LED_MASK;
+  uint8_t new_state = App.get_app_state() & STATUS_LED_MASK;
 
   if (new_state != this->last_app_state_) {
-    ESP_LOGV(TAG, "New app state 0x%08" PRIX32, new_state);
+    ESP_LOGV(TAG, "New app state 0x%02X", new_state);
   }
 
   if ((new_state & STATUS_LED_ERROR) != 0u) {
@@ -53,7 +53,7 @@ void StatusLEDLightOutput::write_state(light::LightState *state) {
 }
 
 void StatusLEDLightOutput::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Status LED...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 
   if (this->pin_ != nullptr) {
     this->pin_->setup();

esphome/components/status_led/light/status_led_light.h

@@ -36,7 +36,7 @@ class StatusLEDLightOutput : public light::LightOutput, public Component {
   GPIOPin *pin_{nullptr};
   output::BinaryOutput *output_{nullptr};
   light::LightState *lightstate_{};
-  uint32_t last_app_state_{0xFFFF};
+  uint8_t last_app_state_{0xFF};
   void output_state_(bool state);
 };
 

esphome/components/status_led/status_led.cpp

@@ -11,7 +11,7 @@ StatusLED *global_status_led = nullptr;  // NOLINT(cppcoreguidelines-avoid-non-c
 
 StatusLED::StatusLED(GPIOPin *pin) : pin_(pin) { global_status_led = this; }
 void StatusLED::pre_setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Status LED...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->pin_->setup();
   this->pin_->digital_write(false);
 }

esphome/components/stepper/stepper.h

@@ -7,9 +7,11 @@ namespace esphome {
 namespace stepper {
 
 #define LOG_STEPPER(this) \
-  ESP_LOGCONFIG(TAG, "  Acceleration: %.0f steps/s^2", this->acceleration_); \
-  ESP_LOGCONFIG(TAG, "  Deceleration: %.0f steps/s^2", this->deceleration_); \
-  ESP_LOGCONFIG(TAG, "  Max Speed: %.0f steps/s", this->max_speed_);
+  ESP_LOGCONFIG(TAG, \
+                "  Acceleration: %.0f steps/s^2\n" \
+                "  Deceleration: %.0f steps/s^2\n" \
+                "  Max Speed: %.0f steps/s", \
+                this->acceleration_, this->deceleration_, this->max_speed_);
 
 class Stepper {
  public:

esphome/components/sts3x/sts3x.cpp

@@ -18,7 +18,7 @@ static const uint16_t STS3X_COMMAND_HEATER_DISABLE = 0x3066;
 static const uint16_t STS3X_COMMAND_FETCH_DATA = 0xE000;
 
 void STS3XComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up STS3x...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (!this->write_command(STS3X_COMMAND_READ_SERIAL_NUMBER)) {
     this->mark_failed();
     return;
@@ -36,7 +36,7 @@ void STS3XComponent::dump_config() {
   ESP_LOGCONFIG(TAG, "STS3x:");
   LOG_I2C_DEVICE(this);
   if (this->is_failed()) {
-    ESP_LOGE(TAG, "Communication with ST3x failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
   LOG_UPDATE_INTERVAL(this);
 

esphome/components/switch/__init__.py

@@ -159,6 +159,7 @@ async def register_switch(var, config):
     if not CORE.has_id(config[CONF_ID]):
         var = cg.Pvariable(config[CONF_ID], var)
     cg.add(cg.App.register_switch(var))
+    CORE.register_platform_component("switch", var)
     await setup_switch_core_(var, config)
 
 

esphome/components/switch/switch.cpp

@@ -65,7 +65,24 @@ bool Switch::is_inverted() const { return this->inverted_; }
 
 void log_switch(const char *tag, const char *prefix, const char *type, Switch *obj) {
   if (obj != nullptr) {
-    ESP_LOGCONFIG(tag, "%s%s '%s'", prefix, type, obj->get_name().c_str());
+    // Prepare restore mode string
+    const LogString *onoff = LOG_STR(""), *inverted = onoff, *restore;
+    if (obj->restore_mode & RESTORE_MODE_DISABLED_MASK) {
+      restore = LOG_STR("disabled");
+    } else {
+      onoff = obj->restore_mode & RESTORE_MODE_ON_MASK ? LOG_STR("ON") : LOG_STR("OFF");
+      inverted = obj->restore_mode & RESTORE_MODE_INVERTED_MASK ? LOG_STR("inverted ") : LOG_STR("");
+      restore = obj->restore_mode & RESTORE_MODE_PERSISTENT_MASK ? LOG_STR("restore defaults to") : LOG_STR("always");
+    }
+
+    // Build the base message with mandatory fields
+    ESP_LOGCONFIG(tag,
+                  "%s%s '%s'\n"
+                  "%s  Restore Mode: %s%s %s",
+                  prefix, type, obj->get_name().c_str(), prefix, LOG_STR_ARG(inverted), LOG_STR_ARG(restore),
+                  LOG_STR_ARG(onoff));
+
+    // Add optional fields separately
     if (!obj->get_icon().empty()) {
       ESP_LOGCONFIG(tag, "%s  Icon: '%s'", prefix, obj->get_icon().c_str());
     }
@@ -78,17 +95,6 @@ void log_switch(const char *tag, const char *prefix, const char *type, Switch *o
     if (!obj->get_device_class().empty()) {
       ESP_LOGCONFIG(tag, "%s  Device Class: '%s'", prefix, obj->get_device_class().c_str());
     }
-    const LogString *onoff = LOG_STR(""), *inverted = onoff, *restore;
-    if (obj->restore_mode & RESTORE_MODE_DISABLED_MASK) {
-      restore = LOG_STR("disabled");
-    } else {
-      onoff = obj->restore_mode & RESTORE_MODE_ON_MASK ? LOG_STR("ON") : LOG_STR("OFF");
-      inverted = obj->restore_mode & RESTORE_MODE_INVERTED_MASK ? LOG_STR("inverted ") : LOG_STR("");
-      restore = obj->restore_mode & RESTORE_MODE_PERSISTENT_MASK ? LOG_STR("restore defaults to") : LOG_STR("always");
-    }
-
-    ESP_LOGCONFIG(tag, "%s  Restore Mode: %s%s %s", prefix, LOG_STR_ARG(inverted), LOG_STR_ARG(restore),
-                  LOG_STR_ARG(onoff));
   }
 }