esphome 2025.5.2__py3-none-any.whl → 2025.6.0__py3-none-any.whl

esphome/components/pzemdc/pzemdc.cpp

@@ -54,8 +54,10 @@ void PZEMDC::on_modbus_data(const std::vector<uint8_t> &data) {
 
 void PZEMDC::update() { this->send(PZEM_CMD_READ_IN_REGISTERS, 0, 8); }
 void PZEMDC::dump_config() {
-  ESP_LOGCONFIG(TAG, "PZEMDC:");
-  ESP_LOGCONFIG(TAG, "  Address: 0x%02X", this->address_);
+  ESP_LOGCONFIG(TAG,
+                "PZEMDC:\n"
+                "  Address: 0x%02X",
+                this->address_);
   LOG_SENSOR("", "Voltage", this->voltage_sensor_);
   LOG_SENSOR("", "Current", this->current_sensor_);
   LOG_SENSOR("", "Power", this->power_sensor_);

esphome/components/qmc5883l/qmc5883l.cpp

@@ -24,7 +24,7 @@ static const uint8_t QMC5883L_REGISTER_CONTROL_2 = 0x0A;
 static const uint8_t QMC5883L_REGISTER_PERIOD = 0x0B;
 
 void QMC5883LComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up QMC5883L...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   // Soft Reset
   if (!this->write_byte(QMC5883L_REGISTER_CONTROL_2, 1 << 7)) {
     this->error_code_ = COMMUNICATION_FAILED;
@@ -69,7 +69,7 @@ void QMC5883LComponent::dump_config() {
   ESP_LOGCONFIG(TAG, "QMC5883L:");
   LOG_I2C_DEVICE(this);
   if (this->error_code_ == COMMUNICATION_FAILED) {
-    ESP_LOGE(TAG, "Communication with QMC5883L failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
   LOG_UPDATE_INTERVAL(this);
 

esphome/components/qmp6988/qmp6988.cpp

@@ -348,7 +348,7 @@ void QMP6988Component::calculate_pressure_() {
 }
 
 void QMP6988Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up QMP6988");
+  ESP_LOGCONFIG(TAG, "Running setup");
 
   bool ret;
   ret = this->device_check_();
@@ -368,7 +368,7 @@ void QMP6988Component::dump_config() {
   ESP_LOGCONFIG(TAG, "QMP6988:");
   LOG_I2C_DEVICE(this);
   if (this->is_failed()) {
-    ESP_LOGE(TAG, "Communication with QMP6988 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
   LOG_UPDATE_INTERVAL(this);
 

esphome/components/qmp6988/qmp6988.h

@@ -1,9 +1,9 @@
 #pragma once
 
-#include "esphome/core/log.h"
 #include "esphome/core/component.h"
 #include "esphome/core/hal.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 #include "esphome/components/sensor/sensor.h"
 #include "esphome/components/i2c/i2c.h"
 

esphome/components/qr_code/qr_code.cpp

@@ -9,8 +9,10 @@ namespace qr_code {
 static const char *const TAG = "qr_code";
 
 void QrCode::dump_config() {
-  ESP_LOGCONFIG(TAG, "QR code:");
-  ESP_LOGCONFIG(TAG, "  Value: '%s'", this->value_.c_str());
+  ESP_LOGCONFIG(TAG,
+                "QR code:\n"
+                "  Value: '%s'",
+                this->value_.c_str());
 }
 
 void QrCode::set_value(const std::string &value) {
@@ -24,7 +26,7 @@ void QrCode::set_ecc(qrcodegen_Ecc ecc) {
 }
 
 void QrCode::generate_qr_code() {
-  ESP_LOGV(TAG, "Generating QR code...");
+  ESP_LOGV(TAG, "Generating QR code");
   uint8_t tempbuffer[qrcodegen_BUFFER_LEN_MAX];
 
   if (!qrcodegen_encodeText(this->value_.c_str(), tempbuffer, this->qr_, this->ecc_, qrcodegen_VERSION_MIN,

esphome/components/qspi_dbi/qspi_dbi.cpp

@@ -6,7 +6,7 @@ namespace esphome {
 namespace qspi_dbi {
 
 void QspiDbi::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up QSPI_DBI");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->spi_setup();
   if (this->enable_pin_ != nullptr) {
     this->enable_pin_->setup();

esphome/components/qwiic_pir/qwiic_pir.cpp

@@ -7,35 +7,28 @@ namespace qwiic_pir {
 static const char *const TAG = "qwiic_pir";
 
 void QwiicPIRComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Qwiic PIR...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 
   // Verify I2C communcation by reading and verifying the chip ID
   uint8_t chip_id;
-
   if (!this->read_byte(QWIIC_PIR_CHIP_ID, &chip_id)) {
-    ESP_LOGE(TAG, "Failed to read the chip's ID");
-
+    ESP_LOGE(TAG, "Failed to read chip ID");
     this->error_code_ = ERROR_COMMUNICATION_FAILED;
     this->mark_failed();
-
     return;
   }
 
   if (chip_id != QWIIC_PIR_DEVICE_ID) {
-    ESP_LOGE(TAG, "Unknown chip ID, is this a Qwiic PIR?");
-
+    ESP_LOGE(TAG, "Unknown chip ID");
     this->error_code_ = ERROR_WRONG_CHIP_ID;
     this->mark_failed();
-
     return;
   }
 
   if (!this->write_byte_16(QWIIC_PIR_DEBOUNCE_TIME, this->debounce_time_)) {
-    ESP_LOGE(TAG, "Failed to configure debounce time.");
-
+    ESP_LOGE(TAG, "Failed to configure debounce time");
     this->error_code_ = ERROR_COMMUNICATION_FAILED;
     this->mark_failed();
-
     return;
   }
 
@@ -43,11 +36,9 @@ void QwiicPIRComponent::setup() {
     // Publish the starting raw state of the PIR sensor
     // If NATIVE mode, the binary_sensor state would be unknown until a motion event
     if (!this->read_byte(QWIIC_PIR_EVENT_STATUS, &this->event_register_.reg)) {
-      ESP_LOGE(TAG, "Failed to read initial sensor state.");
-
+      ESP_LOGE(TAG, "Failed to read initial state");
       this->error_code_ = ERROR_COMMUNICATION_FAILED;
       this->mark_failed();
-
       return;
     }
 
@@ -58,8 +49,7 @@ void QwiicPIRComponent::setup() {
 void QwiicPIRComponent::loop() {
   // Read Event Register
   if (!this->read_byte(QWIIC_PIR_EVENT_STATUS, &this->event_register_.reg)) {
-    ESP_LOGW(TAG, "Failed to communicate with sensor");
-
+    ESP_LOGW(TAG, ESP_LOG_MSG_COMM_FAIL);
     return;
   }
 
@@ -98,39 +88,47 @@ void QwiicPIRComponent::loop() {
 }
 
 void QwiicPIRComponent::dump_config() {
-  ESP_LOGCONFIG(TAG, "Qwiic PIR:");
+  static const char *const RAW = "RAW";
+  static const char *const NATIVE = "NATIVE";
+  static const char *const HYBRID = "HYBRID";
 
-  if (this->debounce_mode_ == RAW_DEBOUNCE_MODE) {
-    ESP_LOGCONFIG(TAG, "  Debounce Mode: RAW");
-  } else if (this->debounce_mode_ == NATIVE_DEBOUNCE_MODE) {
-    ESP_LOGCONFIG(TAG, "  Debounce Mode: NATIVE");
-    ESP_LOGCONFIG(TAG, "  Debounce Time: %ums", this->debounce_time_);
+  const char *debounce_mode_str = RAW;
+  if (this->debounce_mode_ == NATIVE_DEBOUNCE_MODE) {
+    debounce_mode_str = NATIVE;
   } else if (this->debounce_mode_ == HYBRID_DEBOUNCE_MODE) {
-    ESP_LOGCONFIG(TAG, "  Debounce Mode: HYBRID");
+    debounce_mode_str = HYBRID;
+  }
+
+  ESP_LOGCONFIG(TAG,
+                "Qwiic PIR:\n"
+                "  Debounce Mode: %s",
+                debounce_mode_str);
+  if (this->debounce_mode_ == NATIVE_DEBOUNCE_MODE) {
+    ESP_LOGCONFIG(TAG, "  Debounce Time: %ums", this->debounce_time_);
   }
 
   switch (this->error_code_) {
     case NONE:
       break;
     case ERROR_COMMUNICATION_FAILED:
-      ESP_LOGE(TAG, "  Communication with Qwiic PIR failed!");
+      ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
       break;
     case ERROR_WRONG_CHIP_ID:
-      ESP_LOGE(TAG, "  Qwiic PIR has wrong chip ID - please verify you are using a Qwiic PIR");
+      ESP_LOGE(TAG, "Unknown chip ID");
       break;
     default:
-      ESP_LOGE(TAG, "  Qwiic PIR error code %d", (int) this->error_code_);
+      ESP_LOGE(TAG, "Error %d", (int) this->error_code_);
       break;
   }
 
   LOG_I2C_DEVICE(this);
-  LOG_BINARY_SENSOR("  ", "Qwiic PIR Binary Sensor", this);
+  LOG_BINARY_SENSOR("  ", "Binary Sensor", this);
 }
 
 void QwiicPIRComponent::clear_events_() {
   // Clear event status register
   if (!this->write_byte(QWIIC_PIR_EVENT_STATUS, 0x00))
-    ESP_LOGW(TAG, "Failed to clear events on sensor");
+    ESP_LOGW(TAG, "Failed to clear events");
 }
 
 }  // namespace qwiic_pir

esphome/components/rc522/rc522.cpp

@@ -46,7 +46,7 @@ void RC522::setup() {
     reset_pin_->pin_mode(gpio::FLAG_INPUT);
 
     if (!reset_pin_->digital_read()) {  // The MFRC522 chip is in power down mode.
-      ESP_LOGV(TAG, "Power down mode detected. Hard resetting...");
+      ESP_LOGV(TAG, "Power down mode detected. Hard resetting");
       reset_pin_->pin_mode(gpio::FLAG_OUTPUT);  // Now set the resetPowerDownPin as digital output.
       reset_pin_->digital_write(false);         // Make sure we have a clean LOW state.
       delayMicroseconds(2);             // 8.8.1 Reset timing requirements says about 100ns. Let us be generous: 2μsl
@@ -101,7 +101,7 @@ void RC522::dump_config() {
     case NONE:
       break;
     case RESET_FAILED:
-      ESP_LOGE(TAG, "Reset command failed!");
+      ESP_LOGE(TAG, "Reset command failed");
       break;
   }
 
@@ -292,7 +292,7 @@ void RC522::pcd_reset_() {
     return;
 
   if (reset_count_ == RESET_COUNT) {
-    ESP_LOGI(TAG, "Soft reset...");
+    ESP_LOGI(TAG, "Soft reset");
     // Issue the SoftReset command.
     pcd_write_register(COMMAND_REG, PCD_SOFT_RESET);
   }
@@ -300,14 +300,14 @@ void RC522::pcd_reset_() {
   // Expect the PowerDown bit in CommandReg to be cleared (max 3x50ms)
   if ((pcd_read_register(COMMAND_REG) & (1 << 4)) == 0) {
     reset_count_ = 0;
-    ESP_LOGI(TAG, "Device online.");
+    ESP_LOGI(TAG, "Device online");
     // Wait for initialize
     reset_timeout_ = millis();
     return;
   }
 
   if (--reset_count_ == 0) {
-    ESP_LOGE(TAG, "Unable to reset RC522.");
+    ESP_LOGE(TAG, "Unable to reset");
     this->error_code_ = RESET_FAILED;
     mark_failed();
   }

esphome/components/rdm6300/rdm6300.cpp

@@ -1,4 +1,5 @@
 #include "rdm6300.h"
+#include "esphome/core/helpers.h"
 #include "esphome/core/log.h"
 
 namespace esphome {

esphome/components/remote_receiver/__init__.py

@@ -1,6 +1,6 @@
 from esphome import pins
 import esphome.codegen as cg
-from esphome.components import esp32_rmt, remote_base
+from esphome.components import esp32, esp32_rmt, remote_base
 import esphome.config_validation as cv
 from esphome.const import (
     CONF_BUFFER_SIZE,
@@ -128,7 +128,9 @@ CONFIG_SCHEMA = remote_base.validate_triggers(
                 esp32_idf=192,
                 esp32_s2_idf=192,
                 esp32_s3_idf=192,
+                esp32_p4_idf=192,
                 esp32_c3_idf=96,
+                esp32_c5_idf=96,
                 esp32_c6_idf=96,
                 esp32_h2_idf=96,
             ): cv.All(cv.only_with_esp_idf, cv.int_range(min=2)),
@@ -139,7 +141,13 @@ CONFIG_SCHEMA = remote_base.validate_triggers(
                 CONF_RECEIVE_SYMBOLS,
                 esp32_idf=192,
             ): cv.All(cv.only_with_esp_idf, cv.int_range(min=2)),
-            cv.Optional(CONF_USE_DMA): cv.All(cv.only_with_esp_idf, cv.boolean),
+            cv.Optional(CONF_USE_DMA): cv.All(
+                esp32.only_on_variant(
+                    supported=[esp32.const.VARIANT_ESP32S3, esp32.const.VARIANT_ESP32P4]
+                ),
+                cv.only_with_esp_idf,
+                cv.boolean,
+            ),
         }
     ).extend(cv.COMPONENT_SCHEMA)
 )

esphome/components/remote_receiver/remote_receiver_esp32.cpp

@@ -40,7 +40,7 @@ static bool IRAM_ATTR HOT rmt_callback(rmt_channel_handle_t channel, const rmt_r
 #endif
 
 void RemoteReceiverComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Remote Receiver...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 #if ESP_IDF_VERSION_MAJOR >= 5
   rmt_rx_channel_config_t channel;
   memset(&channel, 0, sizeof(channel));
@@ -161,23 +161,33 @@ void RemoteReceiverComponent::dump_config() {
   ESP_LOGCONFIG(TAG, "Remote Receiver:");
   LOG_PIN("  Pin: ", this->pin_);
 #if ESP_IDF_VERSION_MAJOR >= 5
-  ESP_LOGCONFIG(TAG, "  Clock resolution: %" PRIu32 " hz", this->clock_resolution_);
-  ESP_LOGCONFIG(TAG, "  RMT symbols: %" PRIu32, this->rmt_symbols_);
-  ESP_LOGCONFIG(TAG, "  Filter symbols: %" PRIu32, this->filter_symbols_);
-  ESP_LOGCONFIG(TAG, "  Receive symbols: %" PRIu32, this->receive_symbols_);
+  ESP_LOGCONFIG(TAG,
+                "  Clock resolution: %" PRIu32 " hz\n"
+                "  RMT symbols: %" PRIu32 "\n"
+                "  Filter symbols: %" PRIu32 "\n"
+                "  Receive symbols: %" PRIu32 "\n"
+                "  Tolerance: %" PRIu32 "%s\n"
+                "  Filter out pulses shorter than: %" PRIu32 " us\n"
+                "  Signal is done after %" PRIu32 " us of no changes",
+                this->clock_resolution_, this->rmt_symbols_, this->filter_symbols_, this->receive_symbols_,
+                this->tolerance_, (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%",
+                this->filter_us_, this->idle_us_);
 #else
   if (this->pin_->digital_read()) {
     ESP_LOGW(TAG, "Remote Receiver Signal starts with a HIGH value. Usually this means you have to "
                   "invert the signal using 'inverted: True' in the pin schema!");
   }
-  ESP_LOGCONFIG(TAG, "  Channel: %d", this->channel_);
-  ESP_LOGCONFIG(TAG, "  RMT memory blocks: %d", this->mem_block_num_);
-  ESP_LOGCONFIG(TAG, "  Clock divider: %u", this->clock_divider_);
+  ESP_LOGCONFIG(TAG,
+                "  Channel: %d\n"
+                "  RMT memory blocks: %d\n"
+                "  Clock divider: %u\n"
+                "  Tolerance: %" PRIu32 "%s\n"
+                "  Filter out pulses shorter than: %" PRIu32 " us\n"
+                "  Signal is done after %" PRIu32 " us of no changes",
+                this->channel_, this->mem_block_num_, this->clock_divider_, this->tolerance_,
+                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%", this->filter_us_,
+                this->idle_us_);
 #endif
-  ESP_LOGCONFIG(TAG, "  Tolerance: %" PRIu32 "%s", this->tolerance_,
-                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%");
-  ESP_LOGCONFIG(TAG, "  Filter out pulses shorter than: %" PRIu32 " us", this->filter_us_);
-  ESP_LOGCONFIG(TAG, "  Signal is done after %" PRIu32 " us of no changes", this->idle_us_);
   if (this->is_failed()) {
     ESP_LOGE(TAG, "Configuring RMT driver failed: %s (%s)", esp_err_to_name(this->error_code_),
              this->error_string_.c_str());

esphome/components/remote_receiver/remote_receiver_esp8266.cpp

@@ -1,7 +1,7 @@
 #include "remote_receiver.h"
 #include "esphome/core/hal.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 #ifdef USE_ESP8266
 
@@ -31,7 +31,7 @@ void IRAM_ATTR HOT RemoteReceiverComponentStore::gpio_intr(RemoteReceiverCompone
 }
 
 void RemoteReceiverComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Remote Receiver...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->pin_->setup();
   auto &s = this->store_;
   s.filter_us = this->filter_us_;
@@ -63,11 +63,14 @@ void RemoteReceiverComponent::dump_config() {
     ESP_LOGW(TAG, "Remote Receiver Signal starts with a HIGH value. Usually this means you have to "
                   "invert the signal using 'inverted: True' in the pin schema!");
   }
-  ESP_LOGCONFIG(TAG, "  Buffer Size: %u", this->buffer_size_);
-  ESP_LOGCONFIG(TAG, "  Tolerance: %u%s", this->tolerance_,
-                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%");
-  ESP_LOGCONFIG(TAG, "  Filter out pulses shorter than: %u us", this->filter_us_);
-  ESP_LOGCONFIG(TAG, "  Signal is done after %u us of no changes", this->idle_us_);
+  ESP_LOGCONFIG(TAG,
+                "  Buffer Size: %u\n"
+                "  Tolerance: %u%s\n"
+                "  Filter out pulses shorter than: %u us\n"
+                "  Signal is done after %u us of no changes",
+                this->buffer_size_, this->tolerance_,
+                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%", this->filter_us_,
+                this->idle_us_);
 }
 
 void RemoteReceiverComponent::loop() {

esphome/components/remote_receiver/remote_receiver_libretiny.cpp

@@ -1,7 +1,7 @@
 #include "remote_receiver.h"
 #include "esphome/core/hal.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 #ifdef USE_LIBRETINY
 
@@ -31,7 +31,7 @@ void IRAM_ATTR HOT RemoteReceiverComponentStore::gpio_intr(RemoteReceiverCompone
 }
 
 void RemoteReceiverComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Remote Receiver...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->pin_->setup();
   auto &s = this->store_;
   s.filter_us = this->filter_us_;
@@ -63,11 +63,14 @@ void RemoteReceiverComponent::dump_config() {
     ESP_LOGW(TAG, "Remote Receiver Signal starts with a HIGH value. Usually this means you have to "
                   "invert the signal using 'inverted: True' in the pin schema!");
   }
-  ESP_LOGCONFIG(TAG, "  Buffer Size: %u", this->buffer_size_);
-  ESP_LOGCONFIG(TAG, "  Tolerance: %u%s", this->tolerance_,
-                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%");
-  ESP_LOGCONFIG(TAG, "  Filter out pulses shorter than: %u us", this->filter_us_);
-  ESP_LOGCONFIG(TAG, "  Signal is done after %u us of no changes", this->idle_us_);
+  ESP_LOGCONFIG(TAG,
+                "  Buffer Size: %u\n"
+                "  Tolerance: %u%s\n"
+                "  Filter out pulses shorter than: %u us\n"
+                "  Signal is done after %u us of no changes",
+                this->buffer_size_, this->tolerance_,
+                (this->tolerance_mode_ == remote_base::TOLERANCE_MODE_TIME) ? " us" : "%", this->filter_us_,
+                this->idle_us_);
 }
 
 void RemoteReceiverComponent::loop() {

esphome/components/remote_transmitter/__init__.py

@@ -1,6 +1,6 @@
 from esphome import automation, pins
 import esphome.codegen as cg
-from esphome.components import esp32_rmt, remote_base
+from esphome.components import esp32, esp32_rmt, remote_base
 import esphome.config_validation as cv
 from esphome.const import (
     CONF_CARRIER_DUTY_PERCENT,
@@ -45,13 +45,21 @@ CONFIG_SCHEMA = cv.Schema(
             cv.only_on_esp32, cv.only_with_arduino, cv.int_range(min=1, max=255)
         ),
         cv.Optional(CONF_EOT_LEVEL): cv.All(cv.only_with_esp_idf, cv.boolean),
-        cv.Optional(CONF_USE_DMA): cv.All(cv.only_with_esp_idf, cv.boolean),
+        cv.Optional(CONF_USE_DMA): cv.All(
+            esp32.only_on_variant(
+                supported=[esp32.const.VARIANT_ESP32S3, esp32.const.VARIANT_ESP32P4]
+            ),
+            cv.only_with_esp_idf,
+            cv.boolean,
+        ),
         cv.SplitDefault(
             CONF_RMT_SYMBOLS,
             esp32_idf=64,
             esp32_s2_idf=64,
             esp32_s3_idf=48,
+            esp32_p4_idf=48,
             esp32_c3_idf=48,
+            esp32_c5_idf=48,
             esp32_c6_idf=48,
             esp32_h2_idf=48,
         ): cv.All(cv.only_with_esp_idf, cv.int_range(min=2)),

esphome/components/remote_transmitter/remote_transmitter_esp32.cpp

@@ -11,7 +11,7 @@ namespace remote_transmitter {
 static const char *const TAG = "remote_transmitter";
 
 void RemoteTransmitterComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Remote Transmitter...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->inverted_ = this->pin_->is_inverted();
   this->configure_rmt_();
 }
@@ -19,12 +19,16 @@ void RemoteTransmitterComponent::setup() {
 void RemoteTransmitterComponent::dump_config() {
   ESP_LOGCONFIG(TAG, "Remote Transmitter:");
 #if ESP_IDF_VERSION_MAJOR >= 5
-  ESP_LOGCONFIG(TAG, "  Clock resolution: %" PRIu32 " hz", this->clock_resolution_);
-  ESP_LOGCONFIG(TAG, "  RMT symbols: %" PRIu32, this->rmt_symbols_);
+  ESP_LOGCONFIG(TAG,
+                "  Clock resolution: %" PRIu32 " hz\n"
+                "  RMT symbols: %" PRIu32,
+                this->clock_resolution_, this->rmt_symbols_);
 #else
-  ESP_LOGCONFIG(TAG, "  Channel: %d", this->channel_);
-  ESP_LOGCONFIG(TAG, "  RMT memory blocks: %d", this->mem_block_num_);
-  ESP_LOGCONFIG(TAG, "  Clock divider: %u", this->clock_divider_);
+  ESP_LOGCONFIG(TAG,
+                "  Channel: %d\n"
+                "  RMT memory blocks: %d\n"
+                "  Clock divider: %u",
+                this->channel_, this->mem_block_num_, this->clock_divider_);
 #endif
   LOG_PIN("  Pin: ", this->pin_);
 

esphome/components/remote_transmitter/remote_transmitter_esp8266.cpp

@@ -15,8 +15,10 @@ void RemoteTransmitterComponent::setup() {
 }
 
 void RemoteTransmitterComponent::dump_config() {
-  ESP_LOGCONFIG(TAG, "Remote Transmitter...");
-  ESP_LOGCONFIG(TAG, "  Carrier Duty: %u%%", this->carrier_duty_percent_);
+  ESP_LOGCONFIG(TAG,
+                "Remote Transmitter:\n"
+                "  Carrier Duty: %u%%",
+                this->carrier_duty_percent_);
   LOG_PIN("  Pin: ", this->pin_);
 }
 
@@ -72,7 +74,7 @@ void RemoteTransmitterComponent::space_(uint32_t usec) {
 }
 
 void RemoteTransmitterComponent::send_internal(uint32_t send_times, uint32_t send_wait) {
-  ESP_LOGD(TAG, "Sending remote code...");
+  ESP_LOGD(TAG, "Sending remote code");
   uint32_t on_time, off_time;
   this->calculate_on_off_time_(this->temp_.get_carrier_frequency(), &on_time, &off_time);
   this->target_time_ = 0;

esphome/components/remote_transmitter/remote_transmitter_libretiny.cpp

@@ -15,8 +15,10 @@ void RemoteTransmitterComponent::setup() {
 }
 
 void RemoteTransmitterComponent::dump_config() {
-  ESP_LOGCONFIG(TAG, "Remote Transmitter...");
-  ESP_LOGCONFIG(TAG, "  Carrier Duty: %u%%", this->carrier_duty_percent_);
+  ESP_LOGCONFIG(TAG,
+                "Remote Transmitter:\n"
+                "  Carrier Duty: %u%%",
+                this->carrier_duty_percent_);
   LOG_PIN("  Pin: ", this->pin_);
 }
 
@@ -74,7 +76,7 @@ void RemoteTransmitterComponent::space_(uint32_t usec) {
 }
 
 void RemoteTransmitterComponent::send_internal(uint32_t send_times, uint32_t send_wait) {
-  ESP_LOGD(TAG, "Sending remote code...");
+  ESP_LOGD(TAG, "Sending remote code");
   uint32_t on_time, off_time;
   this->calculate_on_off_time_(this->temp_.get_carrier_frequency(), &on_time, &off_time);
   this->target_time_ = 0;

esphome/components/resistance/resistance_sensor.cpp

@@ -8,9 +8,12 @@ static const char *const TAG = "resistance";
 
 void ResistanceSensor::dump_config() {
   LOG_SENSOR("", "Resistance Sensor", this);
-  ESP_LOGCONFIG(TAG, "  Configuration: %s", this->configuration_ == UPSTREAM ? "UPSTREAM" : "DOWNSTREAM");
-  ESP_LOGCONFIG(TAG, "  Resistor: %.2fΩ", this->resistor_);
-  ESP_LOGCONFIG(TAG, "  Reference Voltage: %.1fV", this->reference_voltage_);
+  ESP_LOGCONFIG(TAG,
+                "  Configuration: %s\n"
+                "  Resistor: %.2fΩ\n"
+                "  Reference Voltage: %.1fV",
+                this->configuration_ == UPSTREAM ? "UPSTREAM" : "DOWNSTREAM", this->resistor_,
+                this->reference_voltage_);
 }
 void ResistanceSensor::process_(float value) {
   if (std::isnan(value)) {

esphome/components/restart/button/restart_button.cpp

@@ -9,7 +9,7 @@ namespace restart {
 static const char *const TAG = "restart.button";
 
 void RestartButton::press_action() {
-  ESP_LOGI(TAG, "Restarting device...");
+  ESP_LOGI(TAG, "Restarting device");
   // Let MQTT settle a bit
   delay(100);  // NOLINT
   App.safe_reboot();

esphome/components/restart/switch/restart_switch.cpp

@@ -13,7 +13,7 @@ void RestartSwitch::write_state(bool state) {
   this->publish_state(false);
 
   if (state) {
-    ESP_LOGI(TAG, "Restarting device...");
+    ESP_LOGI(TAG, "Restarting device");
     // Let MQTT settle a bit
     delay(100);  // NOLINT
     App.safe_reboot();

esphome/components/rotary_encoder/rotary_encoder.cpp

@@ -1,6 +1,6 @@
 #include "rotary_encoder.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace rotary_encoder {
@@ -129,7 +129,7 @@ void IRAM_ATTR HOT RotaryEncoderSensorStore::gpio_intr(RotaryEncoderSensorStore
 }
 
 void RotaryEncoderSensor::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Rotary Encoder '%s'...", this->name_.c_str());
+  ESP_LOGCONFIG(TAG, "Running setup for '%s'", this->name_.c_str());
 
   int32_t initial_value = 0;
   switch (this->restore_mode_) {

esphome/components/rp2040/__init__.py

@@ -10,6 +10,7 @@ from esphome.const import (
     CONF_PLATFORM_VERSION,
     CONF_SOURCE,
     CONF_VERSION,
+    CONF_WATCHDOG_TIMEOUT,
     KEY_CORE,
     KEY_FRAMEWORK_VERSION,
     KEY_TARGET_FRAMEWORK,
@@ -147,6 +148,10 @@ CONFIG_SCHEMA = cv.All(
         {
             cv.Required(CONF_BOARD): cv.string_strict,
             cv.Optional(CONF_FRAMEWORK, default={}): ARDUINO_FRAMEWORK_SCHEMA,
+            cv.Optional(CONF_WATCHDOG_TIMEOUT, default="8388ms"): cv.All(
+                cv.positive_time_period_milliseconds,
+                cv.Range(max=cv.TimePeriod(milliseconds=8388)),
+            ),
         }
     ),
     set_core_data,
@@ -189,6 +194,8 @@ async def to_code(config):
         cg.RawExpression(f"VERSION_CODE({ver.major}, {ver.minor}, {ver.patch})"),
     )
 
+    cg.add_define("USE_RP2040_WATCHDOG_TIMEOUT", config[CONF_WATCHDOG_TIMEOUT])
+
 
 def add_pio_file(component: str, key: str, data: str):
     try:

esphome/components/rp2040/core.cpp

@@ -1,6 +1,7 @@
 #ifdef USE_RP2040
 
 #include "core.h"
+#include "esphome/core/defines.h"
 #include "esphome/core/hal.h"
 #include "esphome/core/helpers.h"
 
@@ -19,7 +20,13 @@ void arch_restart() {
     continue;
   }
 }
-void arch_init() { watchdog_enable(0x7fffff, false); }
+
+void arch_init() {
+#if USE_RP2040_WATCHDOG_TIMEOUT > 0
+  watchdog_enable(USE_RP2040_WATCHDOG_TIMEOUT, false);
+#endif
+}
+
 void IRAM_ATTR HOT arch_feed_wdt() { watchdog_update(); }
 
 uint8_t progmem_read_byte(const uint8_t *addr) {