esphome 2025.5.2__py3-none-any.whl → 2025.6.0__py3-none-any.whl

esphome/components/fs3000/fs3000.cpp

@@ -7,7 +7,7 @@ namespace fs3000 {
 static const char *const TAG = "fs3000";
 
 void FS3000Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up FS3000...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 
   if (model_ == FIVE) {
     // datasheet gives 9 points to interpolate from for the 1005 model

esphome/components/ft5x06/touchscreen/ft5x06_touchscreen.cpp

@@ -1,5 +1,6 @@
 #include "ft5x06_touchscreen.h"
 
+#include "esphome/core/helpers.h"
 #include "esphome/core/log.h"
 
 namespace esphome {
@@ -8,7 +9,7 @@ namespace ft5x06 {
 static const char *const TAG = "ft5x06.touchscreen";
 
 void FT5x06Touchscreen::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up FT5x06 Touchscreen...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (this->interrupt_pin_ != nullptr) {
     this->interrupt_pin_->setup();
     this->interrupt_pin_->pin_mode(gpio::FLAG_INPUT | gpio::FLAG_PULLUP);
@@ -81,9 +82,11 @@ void FT5x06Touchscreen::update_touches() {
 }
 
 void FT5x06Touchscreen::dump_config() {
-  ESP_LOGCONFIG(TAG, "FT5x06 Touchscreen:");
-  ESP_LOGCONFIG(TAG, "  Address: 0x%02X", this->address_);
-  ESP_LOGCONFIG(TAG, "  Vendor ID: 0x%X", (int) this->vendor_id_);
+  ESP_LOGCONFIG(TAG,
+                "FT5x06 Touchscreen:\n"
+                "  Address: 0x%02X\n"
+                "  Vendor ID: 0x%X",
+                this->address_, (int) this->vendor_id_);
 }
 
 bool FT5x06Touchscreen::err_check_(i2c::ErrorCode err, const char *msg) {

esphome/components/ft63x6/ft63x6.cpp

@@ -28,7 +28,7 @@ static const uint8_t FT63X6_ADDR_CHIP_ID = 0xA3;
 static const char *const TAG = "FT63X6";
 
 void FT63X6Touchscreen::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up FT63X6 Touchscreen...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (this->interrupt_pin_ != nullptr) {
     this->interrupt_pin_->pin_mode(gpio::FLAG_INPUT | gpio::FLAG_PULLUP);
     this->interrupt_pin_->setup();
@@ -71,8 +71,10 @@ void FT63X6Touchscreen::dump_config() {
   LOG_I2C_DEVICE(this);
   LOG_PIN("  Interrupt Pin: ", this->interrupt_pin_);
   LOG_PIN("  Reset Pin: ", this->reset_pin_);
-  ESP_LOGCONFIG(TAG, "  X Calibration: [%d, %d]", this->x_raw_min_, this->x_raw_max_);
-  ESP_LOGCONFIG(TAG, "  Y Calibration: [%d, %d]", this->y_raw_min_, this->y_raw_max_);
+  ESP_LOGCONFIG(TAG,
+                "  X Calibration: [%d, %d]\n"
+                "  Y Calibration: [%d, %d]",
+                this->x_raw_min_, this->x_raw_max_, this->y_raw_min_, this->y_raw_max_);
   LOG_UPDATE_INTERVAL(this);
 }
 

esphome/components/gcja5/gcja5.cpp

@@ -14,8 +14,6 @@ namespace gcja5 {
 
 static const char *const TAG = "gcja5";
 
-void GCJA5Component::setup() { ESP_LOGCONFIG(TAG, "Setting up gcja5..."); }
-
 void GCJA5Component::loop() {
   const uint32_t now = App.get_loop_component_start_time();
   if (now - this->last_transmission_ >= 500) {
@@ -78,16 +76,6 @@ bool GCJA5Component::calculate_checksum_() {
   return (crc == this->rx_message_[30]);
 }
 
-uint32_t GCJA5Component::get_32_bit_uint_(uint8_t start_index) {
-  return (((uint32_t) this->rx_message_[start_index + 3]) << 24) |
-         (((uint32_t) this->rx_message_[start_index + 2]) << 16) |
-         (((uint32_t) this->rx_message_[start_index + 1]) << 8) | ((uint32_t) this->rx_message_[start_index]);
-}
-
-uint16_t GCJA5Component::get_16_bit_uint_(uint8_t start_index) {
-  return (((uint32_t) this->rx_message_[start_index + 1]) << 8) | ((uint32_t) this->rx_message_[start_index]);
-}
-
 void GCJA5Component::parse_data_() {
   ESP_LOGVV(TAG, "GCJA5 Data: ");
   for (uint8_t i = 0; i < 32; i++) {

esphome/components/gcja5/gcja5.h

@@ -1,6 +1,7 @@
 #pragma once
 
 #include "esphome/core/component.h"
+#include "esphome/core/helpers.h"
 #include "esphome/components/sensor/sensor.h"
 #include "esphome/components/uart/uart.h"
 
@@ -9,7 +10,6 @@ namespace gcja5 {
 
 class GCJA5Component : public Component, public uart::UARTDevice {
  public:
-  void setup() override;
   void dump_config() override;
   void loop() override;
   float get_setup_priority() const override { return setup_priority::DATA; }
@@ -29,8 +29,13 @@ class GCJA5Component : public Component, public uart::UARTDevice {
   void parse_data_();
   bool calculate_checksum_();
 
-  uint32_t get_32_bit_uint_(uint8_t start_index);
-  uint16_t get_16_bit_uint_(uint8_t start_index);
+  uint16_t get_16_bit_uint_(uint8_t start_index) const {
+    return encode_uint16(this->rx_message_[start_index + 1], this->rx_message_[start_index]);
+  }
+  uint32_t get_32_bit_uint_(uint8_t start_index) const {
+    return encode_uint32(this->rx_message_[start_index + 3], this->rx_message_[start_index + 2],
+                         this->rx_message_[start_index + 1], this->rx_message_[start_index]);
+  }
   uint32_t last_transmission_{0};
   std::vector<uint8_t> rx_message_;
 

esphome/components/gdk101/gdk101.cpp

@@ -34,7 +34,7 @@ void GDK101Component::update() {
 
 void GDK101Component::setup() {
   uint8_t data[2];
-  ESP_LOGCONFIG(TAG, "Setting up GDK101...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   // first, reset the sensor
   if (!this->reset_sensor_(data)) {
     this->status_set_error("Reset failed!");
@@ -60,7 +60,7 @@ void GDK101Component::dump_config() {
   ESP_LOGCONFIG(TAG, "GDK101:");
   LOG_I2C_DEVICE(this);
   if (this->is_failed()) {
-    ESP_LOGE(TAG, "Communication with GDK101 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
 #ifdef USE_SENSOR
   LOG_SENSOR("  ", "Firmware Version", this->fw_version_sensor_);

esphome/components/globals/globals_component.h

@@ -1,7 +1,7 @@
 #pragma once
 
-#include "esphome/core/component.h"
 #include "esphome/core/automation.h"
+#include "esphome/core/component.h"
 #include "esphome/core/helpers.h"
 #include <cstring>
 
@@ -39,7 +39,7 @@ template<typename T> class RestoringGlobalsComponent : public Component {
   void setup() override {
     this->rtc_ = global_preferences->make_preference<T>(1944399030U ^ this->name_hash_);
     this->rtc_.load(&this->value_);
-    memcpy(&this->prev_value_, &this->value_, sizeof(T));
+    memcpy(&this->last_checked_value_, &this->value_, sizeof(T));
   }
 
   float get_setup_priority() const override { return setup_priority::HARDWARE; }
@@ -52,15 +52,15 @@ template<typename T> class RestoringGlobalsComponent : public Component {
 
  protected:
   void store_value_() {
-    int diff = memcmp(&this->value_, &this->prev_value_, sizeof(T));
+    int diff = memcmp(&this->value_, &this->last_checked_value_, sizeof(T));
     if (diff != 0) {
       this->rtc_.save(&this->value_);
-      memcpy(&this->prev_value_, &this->value_, sizeof(T));
+      memcpy(&this->last_checked_value_, &this->value_, sizeof(T));
     }
   }
 
   T value_{};
-  T prev_value_{};
+  T last_checked_value_{};
   uint32_t name_hash_{};
   ESPPreferenceObject rtc_;
 };
@@ -85,7 +85,7 @@ template<typename T, uint8_t SZ> class RestoringGlobalStringComponent : public C
     if (hasdata) {
       this->value_.assign(temp + 1, temp[0]);
     }
-    this->prev_value_.assign(this->value_);
+    this->last_checked_value_.assign(this->value_);
   }
 
   float get_setup_priority() const override { return setup_priority::HARDWARE; }
@@ -98,13 +98,12 @@ template<typename T, uint8_t SZ> class RestoringGlobalStringComponent : public C
 
  protected:
   void store_value_() {
-    int diff = this->value_.compare(this->prev_value_);
+    int diff = this->value_.compare(this->last_checked_value_);
     if (diff != 0) {
       // Make it into a length prefixed thing
       unsigned char temp[SZ];
 
       // If string is bigger than the allocation, do not save it.
-      // We don't need to waste ram setting prev_value either.
       int size = this->value_.size();
       // Less than, not less than or equal, SZ includes the length byte.
       if (size < SZ) {
@@ -112,13 +111,17 @@ template<typename T, uint8_t SZ> class RestoringGlobalStringComponent : public C
         // SZ should be pre checked at the schema level, it can't go past the char range.
         temp[0] = ((unsigned char) size);
         this->rtc_.save(&temp);
-        this->prev_value_.assign(this->value_);
       }
+      // Always update last_checked_value_ to match current value, even for oversized strings.
+      // This prevents redundant size checks on every loop iteration when a string remains oversized.
+      // Without this, the diff != 0 check would pass repeatedly for the same oversized string,
+      // wasting CPU cycles on size comparisons.
+      this->last_checked_value_.assign(this->value_);
     }
   }
 
   T value_{};
-  T prev_value_{};
+  T last_checked_value_{};
   uint32_t name_hash_{};
   ESPPreferenceObject rtc_;
 };

esphome/components/gp2y1010au0f/gp2y1010au0f.cpp

@@ -13,8 +13,10 @@ static const float MAX_VOLTAGE = 4.0f;
 
 void GP2Y1010AU0FSensor::dump_config() {
   LOG_SENSOR("", "Sharp GP2Y1010AU0F PM2.5 Sensor", this);
-  ESP_LOGCONFIG(TAG, "  Sampling duration: %" PRId32 " ms", this->sample_duration_);
-  ESP_LOGCONFIG(TAG, "  ADC voltage multiplier: %.3f", this->voltage_multiplier_);
+  ESP_LOGCONFIG(TAG,
+                "  Sampling duration: %" PRId32 " ms\n"
+                "  ADC voltage multiplier: %.3f",
+                this->sample_duration_, this->voltage_multiplier_);
   LOG_UPDATE_INTERVAL(this);
 }
 

esphome/components/gp8403/gp8403.cpp

@@ -12,8 +12,10 @@ static const uint8_t RANGE_REGISTER = 0x01;
 void GP8403::setup() { this->write_register(RANGE_REGISTER, (uint8_t *) (&this->voltage_), 1); }
 
 void GP8403::dump_config() {
-  ESP_LOGCONFIG(TAG, "GP8403:");
-  ESP_LOGCONFIG(TAG, "  Voltage: %dV", this->voltage_ == GP8403_VOLTAGE_5V ? 5 : 10);
+  ESP_LOGCONFIG(TAG,
+                "GP8403:\n"
+                "  Voltage: %dV",
+                this->voltage_ == GP8403_VOLTAGE_5V ? 5 : 10);
   LOG_I2C_DEVICE(this);
 }
 

esphome/components/gp8403/output/gp8403_output.cpp

@@ -10,8 +10,10 @@ static const char *const TAG = "gp8403.output";
 static const uint8_t OUTPUT_REGISTER = 0x02;
 
 void GP8403Output::dump_config() {
-  ESP_LOGCONFIG(TAG, "GP8403 Output:");
-  ESP_LOGCONFIG(TAG, "  Channel: %u", this->channel_);
+  ESP_LOGCONFIG(TAG,
+                "GP8403 Output:\n"
+                "  Channel: %u",
+                this->channel_);
 }
 
 void GP8403Output::write_state(float state) {

esphome/components/gpio/one_wire/gpio_one_wire.cpp

@@ -1,6 +1,6 @@
 #include "gpio_one_wire.h"
-#include "esphome/core/log.h"
 #include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace gpio {
@@ -8,7 +8,7 @@ namespace gpio {
 static const char *const TAG = "gpio.one_wire";
 
 void GPIOOneWireBus::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up 1-wire bus...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->t_pin_->setup();
   this->t_pin_->pin_mode(gpio::FLAG_INPUT | gpio::FLAG_PULLUP);
   // clear bus with 480µs high, otherwise initial reset in search might fail

esphome/components/gpio/output/gpio_binary_output.cpp

@@ -7,7 +7,7 @@ namespace gpio {
 static const char *const TAG = "gpio.output";
 
 void GPIOBinaryOutput::dump_config() {
-  ESP_LOGCONFIG(TAG, "GPIO Binary Output:");
+  ESP_LOGCONFIG(TAG, "Binary Output:");
   LOG_PIN("  Pin: ", this->pin_);
   LOG_BINARY_OUTPUT(this);
 }

esphome/components/gpio/switch/gpio_switch.cpp

@@ -8,7 +8,7 @@ static const char *const TAG = "switch.gpio";
 
 float GPIOSwitch::get_setup_priority() const { return setup_priority::HARDWARE; }
 void GPIOSwitch::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up GPIO Switch '%s'...", this->name_.c_str());
+  ESP_LOGCONFIG(TAG, "Running setup for '%s'", this->name_.c_str());
 
   bool initial_state = this->get_initial_state_with_restore_mode().value_or(false);
 

esphome/components/graphical_display_menu/graphical_display_menu.cpp

@@ -36,14 +36,18 @@ void GraphicalDisplayMenu::setup() {
 }
 
 void GraphicalDisplayMenu::dump_config() {
-  ESP_LOGCONFIG(TAG, "Graphical Display Menu");
-  ESP_LOGCONFIG(TAG, "Has Display: %s", YESNO(this->display_ != nullptr));
-  ESP_LOGCONFIG(TAG, "Popup Mode: %s", YESNO(this->display_ != nullptr));
-  ESP_LOGCONFIG(TAG, "Advanced Drawing Mode: %s", YESNO(this->display_ == nullptr));
-  ESP_LOGCONFIG(TAG, "Has Font: %s", YESNO(this->font_ != nullptr));
-  ESP_LOGCONFIG(TAG, "Mode: %s", this->mode_ == display_menu_base::MENU_MODE_ROTARY ? "Rotary" : "Joystick");
-  ESP_LOGCONFIG(TAG, "Active: %s", YESNO(this->active_));
-  ESP_LOGCONFIG(TAG, "Menu items:");
+  ESP_LOGCONFIG(TAG,
+                "Graphical Display Menu\n"
+                "Has Display: %s\n"
+                "Popup Mode: %s\n"
+                "Advanced Drawing Mode: %s\n"
+                "Has Font: %s\n"
+                "Mode: %s\n"
+                "Active: %s\n"
+                "Menu items:",
+                YESNO(this->display_ != nullptr), YESNO(this->display_ != nullptr), YESNO(this->display_ == nullptr),
+                YESNO(this->font_ != nullptr),
+                this->mode_ == display_menu_base::MENU_MODE_ROTARY ? "Rotary" : "Joystick", YESNO(this->active_));
   for (size_t i = 0; i < this->displayed_item_->items_size(); i++) {
     auto *item = this->displayed_item_->get_item(i);
     ESP_LOGCONFIG(TAG, "  %i: %s (Type: %s, Immediate Edit: %s)", i, item->get_text().c_str(),

esphome/components/grove_gas_mc_v2/grove_gas_mc_v2.cpp

@@ -33,8 +33,7 @@ bool GroveGasMultichannelV2Component::read_sensor_(uint8_t address, sensor::Sens
 }
 
 void GroveGasMultichannelV2Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Grove Multichannel Gas Sensor V2...");
-
+  ESP_LOGCONFIG(TAG, "Running setup");
   // Before reading sensor values, must preheat sensor
   if (!(this->write_bytes(GROVE_GAS_MC_V2_HEAT_ON, {}))) {
     this->mark_failed();
@@ -68,17 +67,17 @@ void GroveGasMultichannelV2Component::dump_config() {
   if (this->is_failed()) {
     switch (this->error_code_) {
       case COMMUNICATION_FAILED:
-        ESP_LOGW(TAG, "Communication failed! Is the sensor connected?");
+        ESP_LOGW(TAG, ESP_LOG_MSG_COMM_FAIL);
         break;
       case APP_INVALID:
-        ESP_LOGW(TAG, "Sensor reported invalid APP installed.");
+        ESP_LOGW(TAG, "Sensor reported invalid APP installed");
         break;
       case APP_START_FAILED:
-        ESP_LOGW(TAG, "Sensor reported APP start failed.");
+        ESP_LOGW(TAG, "Sensor reported APP start failed");
         break;
       case UNKNOWN:
       default:
-        ESP_LOGW(TAG, "Unknown setup error!");
+        ESP_LOGW(TAG, "Unknown setup error");
         break;
     }
   }

esphome/components/grove_tb6612fng/grove_tb6612fng.cpp

@@ -24,7 +24,7 @@ void GroveMotorDriveTB6612FNG::dump_config() {
 }
 
 void GroveMotorDriveTB6612FNG::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up Grove Motor Drive TB6612FNG ...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (!this->standby()) {
     this->mark_failed();
     return;

esphome/components/grove_tb6612fng/grove_tb6612fng.h

@@ -1,9 +1,9 @@
 #pragma once
 
 #include "esphome/components/i2c/i2c.h"
+#include "esphome/core/automation.h"
 #include "esphome/core/component.h"
 #include "esphome/core/hal.h"
-#include "esphome/core/automation.h"
 //#include "esphome/core/helpers.h"
 
 /*

esphome/components/growatt_solar/growatt_solar.cpp

@@ -1,6 +1,7 @@
 #include "growatt_solar.h"
-#include "esphome/core/log.h"
 #include "esphome/core/application.h"
+#include "esphome/core/helpers.h"
+#include "esphome/core/log.h"
 
 namespace esphome {
 namespace growatt_solar {
@@ -134,8 +135,10 @@ void GrowattSolar::on_modbus_data(const std::vector<uint8_t> &data) {
 }
 
 void GrowattSolar::dump_config() {
-  ESP_LOGCONFIG(TAG, "GROWATT Solar:");
-  ESP_LOGCONFIG(TAG, "  Address: 0x%02X", this->address_);
+  ESP_LOGCONFIG(TAG,
+                "GROWATT Solar:\n"
+                "  Address: 0x%02X",
+                this->address_);
 }
 
 }  // namespace growatt_solar

esphome/components/gt911/touchscreen/gt911_touchscreen.cpp

@@ -25,7 +25,7 @@ static const size_t MAX_BUTTONS = 4;  // max number of buttons scanned
 
 void GT911Touchscreen::setup() {
   i2c::ErrorCode err;
-  ESP_LOGCONFIG(TAG, "Setting up GT911 Touchscreen...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (this->reset_pin_ != nullptr) {
     this->reset_pin_->setup();
     this->reset_pin_->digital_write(false);

esphome/components/haier/haier_base.cpp

@@ -242,7 +242,7 @@ haier_protocol::HandlerError HaierClimateBase::timeout_default_handler_(haier_pr
 }
 
 void HaierClimateBase::setup() {
-  ESP_LOGI(TAG, "Haier initialization...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   // Set timestamp here to give AC time to boot
   this->last_request_timestamp_ = std::chrono::steady_clock::now();
   this->set_phase(ProtocolPhases::SENDING_INIT_1);
@@ -286,7 +286,7 @@ void HaierClimateBase::loop() {
     if (this->action_request_.has_value() && this->prepare_pending_action()) {
       this->set_phase(ProtocolPhases::SENDING_ACTION_COMMAND);
     } else if (this->next_hvac_settings_.valid || this->force_send_control_) {
-      ESP_LOGV(TAG, "Control packet is pending...");
+      ESP_LOGV(TAG, "Control packet is pending");
       this->set_phase(ProtocolPhases::SENDING_CONTROL);
       if (this->next_hvac_settings_.valid) {
         this->current_hvac_settings_ = this->next_hvac_settings_;

esphome/components/haier/hon_climate.cpp

@@ -339,13 +339,20 @@ void HonClimate::set_handlers() {
 
 void HonClimate::dump_config() {
   HaierClimateBase::dump_config();
-  ESP_LOGCONFIG(TAG, "  Protocol version: hOn");
-  ESP_LOGCONFIG(TAG, "  Control method: %d", (uint8_t) this->control_method_);
+  ESP_LOGCONFIG(TAG,
+                "  Protocol version: hOn\n"
+                "  Control method: %d",
+                (uint8_t) this->control_method_);
   if (this->hvac_hardware_info_.has_value()) {
-    ESP_LOGCONFIG(TAG, "  Device protocol version: %s", this->hvac_hardware_info_.value().protocol_version_.c_str());
-    ESP_LOGCONFIG(TAG, "  Device software version: %s", this->hvac_hardware_info_.value().software_version_.c_str());
-    ESP_LOGCONFIG(TAG, "  Device hardware version: %s", this->hvac_hardware_info_.value().hardware_version_.c_str());
-    ESP_LOGCONFIG(TAG, "  Device name: %s", this->hvac_hardware_info_.value().device_name_.c_str());
+    ESP_LOGCONFIG(TAG,
+                  "  Device protocol version: %s\n"
+                  "  Device software version: %s\n"
+                  "  Device hardware version: %s\n"
+                  "  Device name: %s",
+                  this->hvac_hardware_info_.value().protocol_version_.c_str(),
+                  this->hvac_hardware_info_.value().software_version_.c_str(),
+                  this->hvac_hardware_info_.value().hardware_version_.c_str(),
+                  this->hvac_hardware_info_.value().device_name_.c_str());
     ESP_LOGCONFIG(TAG, "  Device features:%s%s%s%s%s",
                   (this->hvac_hardware_info_.value().functions_[0] ? " interactive" : ""),
                   (this->hvac_hardware_info_.value().functions_[1] ? " controller-device" : ""),

esphome/components/havells_solar/havells_solar.cpp

@@ -1,5 +1,6 @@
 #include "havells_solar.h"
 #include "havells_solar_registers.h"
+#include "esphome/core/helpers.h"
 #include "esphome/core/log.h"
 
 namespace esphome {
@@ -123,8 +124,10 @@ void HavellsSolar::on_modbus_data(const std::vector<uint8_t> &data) {
 
 void HavellsSolar::update() { this->send(MODBUS_CMD_READ_IN_REGISTERS, 0, MODBUS_REGISTER_COUNT); }
 void HavellsSolar::dump_config() {
-  ESP_LOGCONFIG(TAG, "HAVELLS Solar:");
-  ESP_LOGCONFIG(TAG, "  Address: 0x%02X", this->address_);
+  ESP_LOGCONFIG(TAG,
+                "HAVELLS Solar:\n"
+                "  Address: 0x%02X",
+                this->address_);
   for (uint8_t i = 0; i < 3; i++) {
     auto phase = this->phases_[i];
     if (!phase.setup)

esphome/components/hbridge/switch/hbridge_switch.cpp

@@ -10,7 +10,7 @@ static const char *const TAG = "switch.hbridge";
 
 float HBridgeSwitch::get_setup_priority() const { return setup_priority::HARDWARE; }
 void HBridgeSwitch::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up H-Bridge Switch '%s'...", this->name_.c_str());
+  ESP_LOGCONFIG(TAG, "Running setup for '%s'", this->name_.c_str());
 
   optional<bool> initial_state = this->get_initial_state_with_restore_mode();
 

esphome/components/hdc1080/hdc1080.cpp

@@ -13,7 +13,7 @@ static const uint8_t HDC1080_CMD_TEMPERATURE = 0x00;
 static const uint8_t HDC1080_CMD_HUMIDITY = 0x01;
 
 void HDC1080Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up HDC1080...");
+  ESP_LOGCONFIG(TAG, "Running setup");
 
   const uint8_t data[2] = {
       0b00000000,  // resolution 14bit for both humidity and temperature
@@ -31,7 +31,7 @@ void HDC1080Component::dump_config() {
   ESP_LOGCONFIG(TAG, "HDC1080:");
   LOG_I2C_DEVICE(this);
   if (this->is_failed()) {
-    ESP_LOGE(TAG, "Communication with HDC1080 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
   LOG_UPDATE_INTERVAL(this);
   LOG_SENSOR("  ", "Temperature", this->temperature_);

esphome/components/he60r/he60r.cpp

@@ -40,8 +40,10 @@ CoverTraits HE60rCover::get_traits() {
 void HE60rCover::dump_config() {
   LOG_COVER("", "HE60R Cover", this);
   this->check_uart_settings(1200, 1, uart::UART_CONFIG_PARITY_EVEN, 8);
-  ESP_LOGCONFIG(TAG, "  Open Duration: %.1fs", this->open_duration_ / 1e3f);
-  ESP_LOGCONFIG(TAG, "  Close Duration: %.1fs", this->close_duration_ / 1e3f);
+  ESP_LOGCONFIG(TAG,
+                "  Open Duration: %.1fs\n"
+                "  Close Duration: %.1fs",
+                this->open_duration_ / 1e3f, this->close_duration_ / 1e3f);
   auto restore = this->restore_state_();
   if (restore.has_value())
     ESP_LOGCONFIG(TAG, "  Saved position %d%%", (int) (restore->position * 100.f));

esphome/components/hlw8012/hlw8012.cpp

@@ -11,7 +11,7 @@ static const uint32_t HLW8012_CLOCK_FREQUENCY = 3579000;
 
 void HLW8012Component::setup() {
   float reference_voltage = 0;
-  ESP_LOGCONFIG(TAG, "Setting up HLW8012...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   this->sel_pin_->setup();
   this->sel_pin_->digital_write(this->current_mode_);
   this->cf_store_.pulse_counter_setup(this->cf_pin_);
@@ -38,9 +38,11 @@ void HLW8012Component::dump_config() {
   LOG_PIN("  SEL Pin: ", this->sel_pin_)
   LOG_PIN("  CF Pin: ", this->cf_pin_)
   LOG_PIN("  CF1 Pin: ", this->cf1_pin_)
-  ESP_LOGCONFIG(TAG, "  Change measurement mode every %" PRIu32, this->change_mode_every_);
-  ESP_LOGCONFIG(TAG, "  Current resistor: %.1f mΩ", this->current_resistor_ * 1000.0f);
-  ESP_LOGCONFIG(TAG, "  Voltage Divider: %.1f", this->voltage_divider_);
+  ESP_LOGCONFIG(TAG,
+                "  Change measurement mode every %" PRIu32 "\n"
+                "  Current resistor: %.1f mΩ\n"
+                "  Voltage Divider: %.1f",
+                this->change_mode_every_, this->current_resistor_ * 1000.0f, this->voltage_divider_);
   LOG_UPDATE_INTERVAL(this)
   LOG_SENSOR("  ", "Voltage", this->voltage_sensor_)
   LOG_SENSOR("  ", "Current", this->current_sensor_)

esphome/components/hm3301/hm3301.cpp

@@ -11,7 +11,7 @@ static const uint8_t PM_2_5_VALUE_INDEX = 6;
 static const uint8_t PM_10_0_VALUE_INDEX = 7;
 
 void HM3301Component::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up HM3301...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   if (i2c::ERROR_OK != this->write(&SELECT_COMM_CMD, 1)) {
     error_code_ = ERROR_COMM;
     this->mark_failed();
@@ -23,7 +23,7 @@ void HM3301Component::dump_config() {
   ESP_LOGCONFIG(TAG, "HM3301:");
   LOG_I2C_DEVICE(this);
   if (error_code_ == ERROR_COMM) {
-    ESP_LOGE(TAG, "Communication with HM3301 failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
 
   LOG_SENSOR("  ", "PM1.0", this->pm_1_0_sensor_);

esphome/components/hmc5883l/hmc5883l.cpp

@@ -22,7 +22,7 @@ static const uint8_t HMC5883L_REGISTER_IDENTIFICATION_B = 0x0B;
 static const uint8_t HMC5883L_REGISTER_IDENTIFICATION_C = 0x0C;
 
 void HMC5883LComponent::setup() {
-  ESP_LOGCONFIG(TAG, "Setting up HMC5583L...");
+  ESP_LOGCONFIG(TAG, "Running setup");
   uint8_t id[3];
   if (!this->read_byte(HMC5883L_REGISTER_IDENTIFICATION_A, &id[0]) ||
       !this->read_byte(HMC5883L_REGISTER_IDENTIFICATION_B, &id[1]) ||
@@ -73,7 +73,7 @@ void HMC5883LComponent::dump_config() {
   ESP_LOGCONFIG(TAG, "HMC5883L:");
   LOG_I2C_DEVICE(this);
   if (this->error_code_ == COMMUNICATION_FAILED) {
-    ESP_LOGE(TAG, "Communication with HMC5883L failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   } else if (this->error_code_ == ID_REGISTERS) {
     ESP_LOGE(TAG, "The ID registers don't match - Is this really an HMC5883L?");
   }

esphome/components/homeassistant/time/homeassistant_time.cpp

@@ -7,8 +7,10 @@ namespace homeassistant {
 static const char *const TAG = "homeassistant.time";
 
 void HomeassistantTime::dump_config() {
-  ESP_LOGCONFIG(TAG, "Home Assistant Time:");
-  ESP_LOGCONFIG(TAG, "  Timezone: '%s'", this->timezone_.c_str());
+  ESP_LOGCONFIG(TAG,
+                "Home Assistant Time:\n"
+                "  Timezone: '%s'",
+                this->timezone_.c_str());
 }
 
 float HomeassistantTime::get_setup_priority() const { return setup_priority::DATA; }

esphome/components/honeywell_hih_i2c/honeywell_hih.cpp

@@ -17,7 +17,7 @@ void HoneywellHIComponent::read_sensor_data_() {
   uint8_t data[4];
 
   if (this->read(data, sizeof(data)) != i2c::ERROR_OK) {
-    ESP_LOGE(TAG, "Communication with Honeywell HIH failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
     this->mark_failed();
     return;
   }
@@ -37,7 +37,7 @@ void HoneywellHIComponent::read_sensor_data_() {
 
 void HoneywellHIComponent::start_measurement_() {
   if (this->write(REQUEST_CMD, sizeof(REQUEST_CMD)) != i2c::ERROR_OK) {
-    ESP_LOGE(TAG, "Communication with Honeywell HIH failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
     this->mark_failed();
     return;
   }
@@ -49,7 +49,7 @@ bool HoneywellHIComponent::is_measurement_ready_() {
   uint8_t data[1];
 
   if (this->read(data, sizeof(data)) != i2c::ERROR_OK) {
-    ESP_LOGE(TAG, "Communication with Honeywell HIH failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
     this->mark_failed();
     return false;
   }
@@ -84,7 +84,7 @@ void HoneywellHIComponent::dump_config() {
   ESP_LOGD(TAG, "Honeywell HIH:");
   LOG_I2C_DEVICE(this);
   if (this->is_failed()) {
-    ESP_LOGE(TAG, "Communication with Honeywell HIH failed!");
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
   }
   LOG_SENSOR("  ", "Temperature", this->temperature_sensor_);
   LOG_SENSOR("  ", "Humidity", this->humidity_sensor_);