cgse 2023.38.0__py3-none-any.whl → 2024.1.4__py3-none-any.whl

egse/tempcontrol/srs/ptc10.yaml

@@ -1,227 +0,0 @@
-BaseClass:
-    egse.tempcontrol.srs.ptc10.ptc10Interface
-
-ProxyClass:
-    egse.tempcontrol.srs.ptc10.ptc10Proxy
-
-ControlServerClass:
-    egse.tempcontrol.srs.ptc10_cs.ptc10ControlServer
-
-ControlServer:
-    egse.tempcontrol.srs.ptc10_cs
-
-UserInterface:
-    egse.tempcontrol.srs.ptc10_ui
-
-Commands:
-
-    # Each of these groups is parsed and used on both the server and the client side.
-    # The group name (e.g. is_simulator) will be monkey patched in the Proxy class for the device or service.
-    # The other field are:
-    #   description:   Used by the doc_string method to generate a help string
-    #   cmd:           Command string that will eventually be send to the hardware controller for the
-    #                  device after the arguments have been filled.
-    #   device_method: The name of the method to be called on the device class.
-    #                  These should all be defined by the base class for the device.
-    #                  This method should exist in the subclass of the CommandProtocol base class.
-
-    # Definition of the the DeviceInterface
-
-    disconnect:
-        description: Disconnect from the Temperature regulator controller. This command will be send to the
-                       Thorlabs Control Server which will then disconnect from the hardware controller.
-                       This command doesn't affect the ZeroMQ connection of this Proxy to the
-                       control server. Use the service command ``disconnect_cs()`` to disconnect
-                       from the control server.
-
-    connect:
-        description:    Connect the temperature hardware controller
-
-    reconnect:
-        description:    Reconnect the temperature hardware controller.
-
-                        This command will force a disconnect and then try to re-connect to the controller.
-
-    is_simulator:
-        description:   Ask if the control server is a simulator instead of the real SRSPTC10Controller class.
-        returns:       bool | True if the far end is a simulator instead of the real hardware
-
-    is_connected:
-        description:   Check if the SRS Hardware Controller is connected.
-
-
-    # Definition of the device commands
-    info:
-        description:    Returns basic information about the device, its name, firmware version etc.
-        returns:        str
-
-    alarm_status:
-        description:    Returns the current status of the Alarm Status Register, and then clears the register.
-        returns:        str
-
-    get_names:
-        description:    Returns a tuple of 2 lists with the names of inputs (4 sensors) in the first list and the names of
-                        outputs (3 heaters) in the second list.
-        returns:         tuple
-
-    set_name:
-        description:    Modifies the name of the specified channel (input or output).
-        cmd:            '{old_name} {new_name}'
-
-    clear_error:
-        description:    Erases all error messages for the port over which the instruction was transmitted. Also clears all messages
-                        from the System.Com. Errors window regardless of which port generated them.
-
-    stop:
-        description:    kill.all stops all currently running macros with the given runtime name. The runtime name is assigned with the
-                        "name" instruction and is not necessarily the same as the file name that a macro may be saved under.
-                        The kill.all instruction stops all currently-running macros regardless of name or which port started the macro.
-
-    standby:
-        description:    Puts the PTC10 into stby mode, in which the outputs are turned off, data acquisition is paused, macros are
-                        paused, the front panel display and system fan are shut off, and the system does not respond to remote commands.
-                        The PTC321's excitation currents remain on, and the chassis cooling fan may switch on occassionally.
-                        Press the "Output Enable" key to exit standby mode. There is no remote command to leave stand by mode.
-
-    reset:
-        description:    Resets the PTC10.
-                        The *RST instruction is equivalent to turning the instrument off and back on again, except the Power On bit of
-                        the Event Status Register is not set. *RST has the following effects
-                        - Outputs are disabled (as if the “Output enable” button were pressed).
-                        - All currently-running macros are stopped, regardless of whether the macros were started by the GPIB interface,
-                        another I/O port, or the Program screen.
-                        - The instrument returns to the Select screen.
-                        -Partially-received instructions on all I/O ports are cleared.
-                        - All pending transmissions on all I/O ports are cancelled.
-                        - The error queues for all I/O ports are cleared.
-                        - The plot screen returns to showing the most recent data on autoscaled Y axes.
-                        - The instrument automatically triggers at the rate set with the “A/D rate” control.
-                        - Clears all locally-stored log data. Logs on USB devices are not affected. If data is not being logged to a
-                        USB storage device, the Plot screen shows no accumulated data immediately after a *RST command.
-
-    read_temperature:
-        description:    Reads the temperature from the 3 PT1000 corresponding to TRP2/TRP3/TRP4.
-        returns:         list
-
-    read_heater:
-        description:    Reads the 3x heater outputs with the unit (W, A or V).
-                        Returns a tuple. 1st element is a list with the 3 values of the heaters. 2nd element is a string with the unit
-                        ('W', 'A' or 'V').
-        returns:         tuple
-
-    disable_heater:
-        description:    Disables the specified heater output. output_ch = 1, 2, 3
-                        <channel>.Off cancels any active autotuning process, turns PID feedback off, and sets the channel's
-                        output to zero or the lower limit.
-        cmd:            '{output_ch}'
-
-    outputs_enable:
-      description:      Enables all outputs. Equivalent to press the red button twice on the front panel of the PTC10 when outputs disabled.
-
-    outputs_disable:
-        description:    Disables all outputs. Equivalent to press the red button on the front panel of the PTC10 when output enabled.
-
-    disable_all:
-      description:      Both disable_heater function used for all heaters AND outputs_disable.
-
-    is_outputs_enable:
-      description:      Returns a boolean corresponding to the state of the red button/light on the front panel of the PTC10.
-                        True means outputs enabled (red light switch on)
-                        False means outputs disabled (red light switch off)
-      returns:           bool
-
-    output_limit:
-        description:    Sets the min and max output and can be used to prevent the PID loop for delivering excessive power to a
-                        heater. The limits must be expressed in the same units that the output is expressed in. The limits must
-                        normally be reset when the output units are changed, since the limits are not converted to the new units.
-                        output_ch = 1, 2, 3
-                        low = float >= 0
-                        high = float > low
-        cmd:            '{output_ch} {low} {high}'
-
-    output_unit:
-        description:    Sets the unit for the 3 heaters
-                        unit = W, A, V, or in lowercase w, a, v
-        cmd:            '{unit}'
-
-    set_heater_input:
-        description:    Sets the sensor as input for the specified heater.
-                        output_ch = 1, 2, 3
-                        input = name of the sensor (e.g. TRP2)
-        cmd:            '{output_ch} {input}'
-
-    setpoint:
-        description:    Sets the temperature setpoint. The PID attemps to keep the input at this value by changing the output.
-                        output_ch = 1, 2, 3
-                        setpoint = float (°C)
-        cmd:            '{output_ch} {setpoint}'
-
-    get_PID:
-        description:    Returns a dictionary with P, I and D parameters as float,
-                        {"P" P_value, "I" I_value, "D" D_value}
-                        output_ch = 1, 2, 3
-        cmd:            '{output_ch}'
-
-    set_PID:
-        description:    The input must be stable before either Step or Relay tuning is started. Furthermore, the output must be greater
-                        than half the step height before starting relay tuning. The best time to start a step response is when the
-                        system is first turned on at the beginning of the day, i.e the heater is cold and its temperature stable.
-                        See User Manual for further details.
-                        input_ch parameter sets the PID input channel which is the temperature that the PID feedback loop controls. intput_ch = 1, 2, 3
-                        output_ch parameter sets the PID output channel. output_ch = 1, 2, 3
-                        PID parameter sets the three coefficients respectively in P, I and D. PID = [float, float, float]
-        cmd:            '{input_ch} {output_ch} {PID}'
-
-    autotune_PID:
-        description:    Configures the PID with autotune.
-                        User Manual p.50 "If the system has never been tuned, start with the feedback turned off and the heater at ambient temperature.
-                        If the system has been tuned before, it’s better to wait for the temperature to stabilize at the setpoint.
-                        In either case, the key to successful autotuning is to start with a stable temperature."
-                        Prints message if failure to autotune PID. Old values for P, I and D are retained.
-                        input_ch parameter sets the PID input channel which is the temperature that the PID feedback loop controls. intput_ch = 1, 2, 3
-                        output_ch parameter sets the PID output channel. output_ch = 1, 2, 3
-        cmd:            '{input_ch} {output_ch}'
-
-    set_auto:
-        description:    Enables the specified output to reach the specified setpoint automatically.
-                        output_ch = 1, 2, 3
-                        setpoint = float (°C)
-        cmd:            '{output_ch} {setpoint}'
-
-    set_manual:
-        description:    Enables the specified output manually with the specified value.
-                        The unit is the one currently in effect (W, A or V).
-                        output_ch = 1, 2, 3
-                        value = float >= 0
-        cmd:            '{output_ch} {value}'
-
-    set_survival:
-        description:    Sets all outputs to the min Non op temperature for TRP2, TRP3 and TRP4 as given in the Setup YAML file.
-                        We assume that P, I and D coefficients are already correctly set.
-
-    set_stable:
-        description:    Sets all outputs to the same temperature setpoint given as parameter.
-                        We assume that P, I and D coefficients are already correctly set.
-        cmd:            '{setpoint}'
-
-    set_custom:
-        description:    Sets the outputs given as parameter to the corresponding temperature given as parameter.
-                        If an output channel is not given as parameter in the dictionary outputs_dict, this output
-                        channel will remain at the same state and with same setpoint as before.
-                        outputs_dict = {output_ch setpoint} for example, { 3 -110, 1 -106 }
-        cmd:            '{outputs_dict}'
-
-    heater_sensor_error:
-        description:    Returns a list with names of sensors (TRP) and heaters which cannot be read by the PTC10.
-        returns:         list
-
-    disable_heater_error:
-        description:    Disables heaters whose PT1000 sensors are faulty.
-                        This function does not re-enable heater if a PT1000 is no longer faulty.
-
-    get_time:
-        description:    Returns PTC10 time as a string.
-        returns:        str
-
-    update_time:
-        description:    Updates the PTC10 date and time in UTC from the server's time which is ntp synchronised.

egse/tempcontrol/srs/ptc10_cs.py

@@ -1,128 +0,0 @@
-import argparse
-import click
-import logging
-import sys
-
-import zmq
-
-from egse.control import ControlServer
-from egse.tempcontrol.srs.ptc10 import ptc10Proxy
-from egse.tempcontrol.srs.ptc10_protocol import ptc10Protocol
-from egse.settings import Settings
-from egse.zmq_ser import connect_address
-from egse.control import is_control_server_active
-
-logger = logging.getLogger(__name__)
-
-CTRL_SETTINGS = Settings.load("SRS PTC10 Control Server")
-
-
-def is_ptc10_cs_active(timeout: float = 0.5):
-    """Check if the DAQ6510 Control Server is running.
-
-    Args:
-        timeout (float): timeout when waiting for a reply [seconds, default=0.5]
-    Returns:
-        True if the control server is running and replied with the expected answer.
-    """
-
-    endpoint = connect_address(
-        CTRL_SETTINGS.PROTOCOL, CTRL_SETTINGS.HOSTNAME, CTRL_SETTINGS.COMMANDING_PORT
-    )
-
-    return is_control_server_active(endpoint, timeout)
-
-
-class ptc10ControlServer(ControlServer):
-    """
-    ptc10ControlServer - Command and monitor the PTC10 Temp Controllers.
-    This class works as a command and monitoring server to control the Temp Controller remotely.
-    The sever binds to the following ZeroMQ sockets:
-    * a REQ-REP socket that can be used as a command server. Any client can connect and
-      send a command to the Temp controller.
-    * a PUB-SUP socket that serves as a monitoring server. It will send out Temp status
-      information to all the connected clients every DELAY seconds.
-    """
-
-    def __init__(self):
-        super().__init__()
-
-        self.device_protocol = ptc10Protocol(self)
-
-        self.logger.debug(f"Binding ZeroMQ socket to {self.device_protocol.get_bind_address()}")
-
-        self.device_protocol.bind(self.dev_ctrl_cmd_sock)
-
-        self.poller.register(self.dev_ctrl_cmd_sock, zmq.POLLIN)
-
-    def get_communication_protocol(self):
-        return CTRL_SETTINGS.PROTOCOL
-
-    def get_commanding_port(self):
-        return CTRL_SETTINGS.COMMANDING_PORT
-
-    def get_service_port(self):
-        return CTRL_SETTINGS.SERVICE_PORT
-
-    def get_monitoring_port(self):
-        return CTRL_SETTINGS.MONITORING_PORT
-
-    def get_storage_mnemonic(self):
-        try:
-            return CTRL_SETTINGS.STORAGE_MNEMONIC
-        except AttributeError:
-            return "DAS-PTC10-EMPTY"
-
-
-@click.group()
-def cli():
-    pass
-
-
-@cli.command()
-@click.option("--simulator", "--sim", is_flag=True, help="Start the PTC10 Temp Simulator as the backend.")
-def start(simulator):
-    """Start the PTC10 Temp Control Server."""
-
-    if simulator:
-
-        Settings.set_simulation_mode(True)
-
-    try:
-
-        controller = ptc10ControlServer()
-        controller.serve()
-
-    except KeyboardInterrupt:
-
-        print("Shutdown requested...exiting")
-
-    except SystemExit as exit_code:
-
-        print("System Exit with code {}.".format(exit_code))
-        sys.exit(exit_code)
-
-    except Exception:
-
-        logger.exception("Cannot start the PTC10 Temp Control Server")
-
-        # The above line does exactly the same as the traceback, but on the logger
-        # import traceback
-        # traceback.print_exc(file=sys.stdout)
-
-    return 0
-
-
-@cli.command()
-def stop():
-    """Send a 'quit_server' command to the PTC10 Temp Control Server."""
-
-    with ptc10Proxy() as proxy:
-
-        sp = proxy.get_service_proxy()
-        sp.quit_server()
-
-
-if __name__ == "__main__":
-
-    sys.exit(cli())

egse/tempcontrol/srs/ptc10_devif.py

@@ -1,118 +0,0 @@
-"""
-The device interface for the temperature regulation controller  that will be used at IAS for TVAC the PLATO Cameras.
-
-"""
-
-import logging
-import time
-import datetime
-from typing import List
-
-from telnetlib import Telnet
-
-
-from egse.settings import Settings
-from egse.exceptions import DeviceNotFoundError
-from egse.device import DeviceConnectionError
-from egse.device import DeviceConnectionInterface, DeviceTransport, DeviceTimeoutError
-from egse.command import ClientServerCommand
-
-logger = logging.getLogger(__name__)
-
-ctrl_settings = Settings.load("SRS PTC10 Controller")
-
-IDENTIFICATION_QUERY = "*IDN?"
-
-
-class ptc10Error(Exception):
-    """Base exception for all ptc10 errors."""
-    pass
-
-class ptc10Command(ClientServerCommand):
-    def get_cmd_string(self, *args, **kwargs) -> str:
-        out = super().get_cmd_string(*args, **kwargs)
-        return out + "\n"
-
-
-class ptc10TelnetInterface(DeviceConnectionInterface, DeviceTransport):
-    "Low level Telnet IF"
-    TELNET_TIMEOUT = 0.5
-
-    def __init__(self):
-        self._temp = None
-        self.telnet = Telnet()
-        self.is_connection_open = False
-        self._id = None
-
-    def connect(self, hostname: str):
-
-        try:
-            self.telnet.open(hostname, 23)
-            time.sleep(0.5)
-            # Asking for instrument description
-            _id = self.get_id()
-            logger.warning(f"Connected to: {_id}")
-
-
-        except (ValueError, Exception) as exc:
-            logger.warning(f"Could not open device connection: {exc}")
-            raise DeviceNotFoundError("Could not open device connection.") from exc
-
-        self.is_connection_open = True
-
-    def disconnect(self):
-        """
-        Disconnects from the device
-        Raises:
-            DeviceConnectionError when the connection has not been closed correctly
-
-        """
-        try:
-            if self.is_connection_open:
-                logger.debug(f"disconnecting from {self._id}")
-
-                self.telnet.read_very_eager()
-                self.telnet.close()
-
-            self.is_connection_open= False
-            logger.info("PTC10 device has been disconnected")
-
-        except Exception as e_exc:
-            raise DeviceConnectionError(f"Couldn't close the device connection: {self.device_id}") from e_exc
-
-    def is_connected(self):
-        """Return True if the device is connected."""
-        if not self.is_connection_open:
-            return False
-        try:
-            self.write(IDENTIFICATION_QUERY)
-            time.sleep(0.1)
-            _id = self.read()
-            time.sleep(0.1)
-        except OSError:  # FIXME: Check which errors are actually thrown here
-            self.disconnect()
-            return False
-        return True
-
-    def get_response(self, cmd_string):
-        pass
-
-    def get_id(self):
-        self.write("Description")
-        self._id = self.read()
-        return self._id
-
-    def write(self, cmd: str):
-        self.telnet.write(cmd.encode() + b"\r\n")
-
-    def read(self):
-        response = self.telnet.read_until(b'\x06\r\n', timeout=self.TELNET_TIMEOUT)
-        response = response.decode()
-        parts = response.replace("\r\n", "")
-        return parts
-
-    def trans(self, cmd: str) -> List:
-        self.write(cmd)
-        response = self.read()
-        return response
-

egse/tempcontrol/srs/ptc10_protocol.py

@@ -1,42 +0,0 @@
-from egse.control import ControlServer
-# from egse.metrics import define_metrics
-from egse.synoptics import SynopticsManagerProxy
-from egse.tempcontrol.srs.ptc10 import ptc10Controller, ptc10Simulator, ptc10Interface
-from egse.tempcontrol.srs.ptc10_devif import ptc10Command
-
-from egse.protocol import CommandProtocol
-from egse.settings import Settings
-from egse.system import format_datetime
-from egse.zmq_ser import bind_address
-
-COMMAND_SETTINGS = Settings.load(filename="ptc10.yaml")
-
-
-class ptc10Protocol(CommandProtocol):
-    def __init__(self, control_server: ControlServer):
-        super().__init__()
-        self.control_server = control_server
-
-        if Settings.simulation_mode():
-            self.temp = ptc10Simulator()
-        else:
-            self.temp = ptc10Controller()
-
-        self.load_commands(
-            COMMAND_SETTINGS.Commands, ptc10Command, ptc10Interface
-        )
-
-        self.build_device_method_lookup_table(self.temp)
-
-    def get_bind_address(self):
-        return bind_address(
-            self.control_server.get_communication_protocol(),
-            self.control_server.get_commanding_port(),
-        )
-
-    def get_status(self):
-        return super().get_status()
-
-    def get_housekeeping(self) -> dict:
-        result = dict()
-        return result