@zwave-js/config 10.0.0-beta.1 → 10.0.0-beta.10

package/config/devices/0x0312/zw39.json

@@ -43,56 +43,16 @@
 		},
 		{
 			"#": "3",
-			"label": "LED Indicator",
-			"description": "Turn LED indicator ON when light is ON (paddle switch only)",
-			"valueSize": 1,
-			"defaultValue": 1,
-			"allowManualEntry": false,
-			"options": [
-				{
-					"label": "OFF",
-					"value": 0
-				},
-				{
-					"label": "ON",
-					"value": 1
-				},
-				{
-					"label": "Disabled",
-					"value": 2
-				},
-				{
-					"label": "Always ON",
-					"value": 3
-				}
-			]
+			"$import": "~/templates/master_template.json#led_indicator_four_options",
+			"defaultValue": 1
 		},
 		{
 			"#": "4",
-			"label": "Invert Switch",
-			"description": "Invert on & off on the physical switch",
-			"valueSize": 1,
-			"defaultValue": 0,
-			"allowManualEntry": false,
-			"options": [
-				{
-					"label": "Disable",
-					"value": 0
-				},
-				{
-					"label": "Enable",
-					"value": 1
-				}
-			]
+			"$import": "~/templates/master_template.json#orientation"
 		},
 		{
 			"#": "5",
-			"label": "Auto Off Timer",
-			"valueSize": 2,
-			"unit": "seconds",
-			"minValue": 0,
-			"maxValue": 32767,
-			"defaultValue": 0
+			"$import": "templates/minoston_template.json#auto_off_timer_32767s"
 		},
 		{
 			"#": "7",

package/config/devices/0x0312/zw922.json

@@ -54,17 +54,17 @@
 		},
 		{
 			"#": "2",
-			"$import": "~/0x0312/templates/minoston_template.json#led_indicator_color_upper"
+			"$import": "templates/minoston_template.json#led_indicator_color_upper"
 		},
 		{
 			"#": "3",
-			"$import": "~/0x0312/templates/minoston_template.json#led_indicator_color_lower"
+			"$import": "templates/minoston_template.json#led_indicator_color_lower"
 		}
 	],
 	"metadata": {
 		"inclusion": "1. Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n2. When prompted by your primary controller, click the Up or Down button six times in one second.\nThe device is compatible with SmartStart\nSmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code found on the top of the outlet or the back of\nthe box with a controller providing SmartStart inclusion.No further action is required and the SmartStart product will be added automatically within\n10 minutes of being switched on and in the network vicinity",
 		"exclusion": "1. Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.\n2. When prompted by your primary controller, click the Up or Down button six times in one second.\nThe device is compatible with SmartStart\nSmartStart enabled products can be added into a Z-Wave™ network by scanning the Z-Wave™ QR Code found on the top of the outlet or the back of\nthe box with a controller providing SmartStart inclusion.No further action is required and the SmartStart product will be added automatically within\n10 minutes of being switched on and in the network vicinity",
-		"reset": "Tap-tap-tap’and’hold to reset, LED indicator will blink red 5 times to confirm successful reset",
+		"reset": "Triple-tap and hold to reset, LED indicator will blink red 5 times to confirm successful reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4080/ZW922-manual-20210118.pdf"
 	}
 }

package/config/devices/0x0312/zw96.json

@@ -28,44 +28,17 @@
 	"paramInformation": [
 		{
 			"#": "1",
-			"label": "LED Indicator",
-			"valueSize": 1,
-			"defaultValue": 0,
-			"allowManualEntry": false,
-			"options": [
-				{
-					"label": "On when load is on",
-					"value": 0
-				},
-				{
-					"label": "On when load is off",
-					"value": 1
-				},
-				{
-					"label": "Disable",
-					"value": 2
-				}
-			]
+			"$import": "~/templates/master_template.json#led_indicator_three_options_inverted"
 		},
 		{
 			"#": "2",
-			"label": "Outlet 1 (Right): Auto Off Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_off_timer",
+			"label": "Outlet 1 (Right): Auto Off Timer"
 		},
 		{
 			"#": "3",
-			"label": "Outlet 1 (Right): Auto On Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_on_timer",
+			"label": "Outlet 1 (Right): Auto On Timer"
 		},
 		{
 			"#": "4",

package/config/devices/0x0312/zw97.json

@@ -32,64 +32,27 @@
 	"paramInformation": [
 		{
 			"#": "1",
-			"label": "LED Indicator",
-			"valueSize": 1,
-			"defaultValue": 0,
-			"allowManualEntry": false,
-			"options": [
-				{
-					"label": "On when load is on",
-					"value": 0
-				},
-				{
-					"label": "On when load is off",
-					"value": 1
-				},
-				{
-					"label": "Disable",
-					"value": 2
-				}
-			]
+			"$import": "~/templates/master_template.json#led_indicator_three_options_inverted"
 		},
 		{
 			"#": "2",
-			"label": "Outlet 1 (Left): Auto Off Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_off_timer",
+			"label": "Outlet 1 (Left): Auto Off Timer"
 		},
 		{
 			"#": "4",
-			"label": "Outlet 1 (Left): Auto On Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_on_timer",
+			"label": "Outlet 1 (Left): Auto On Timer"
 		},
 		{
 			"#": "3",
-			"label": "Outlet 2 (Right): Auto Off Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_off_timer",
+			"label": "Outlet 2 (Right): Auto Off Timer"
 		},
 		{
 			"#": "5",
-			"label": "Outlet 2 (Right): Auto On Timer",
-			"valueSize": 4,
-			"unit": "minutes",
-			"minValue": 0,
-			"maxValue": 65535,
-			"defaultValue": 0,
-			"unsigned": true
+			"$import": "templates/minoston_template.json#auto_on_timer",
+			"label": "Outlet 2 (Right): Auto On Timer"
 		},
 		{
 			"#": "6",

package/config/devices/0x0330/ves-zw-dim-001.json

@@ -245,7 +245,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Step 1. Set primary controller/gateway into inclusion mode.\nStep 2. Either power cycle the product, or triple press the action button.\n Step 3. The connected light will stay on solid for 3 seconds to indicate successfuly inclusion.",
+		"inclusion": "Step 1. Set primary controller/gateway into inclusion mode.\nStep 2. Either power cycle the product, or triple press the action button.\n Step 3. The connected light will stay on solid for 3 seconds to indicate successful inclusion.",
 		"exclusion": "Step 1. Set primary controller/gateway into exclusion mode.\nStep 2. Triple press the action button.",
 		"reset": "Press and hold the action button for over 10 seconds. The connected light will be set to 50% brightness and flash slowly.",
 		"manual": "https://cdn.shopify.com/s/files/1/0066/8149/3559/files/VES-ZW-DIM-001.pdf"

package/config/devices/0x033f/asl-03.json

@@ -24,7 +24,7 @@
 	},
 	"metadata": {
 		"inclusion": "In order to include the August Smart Lock on to a Z-Wave network the user will have to do the following:\n\n1. Open the August app\n\n2. Go to the Lock Settings screen\n\n3. Select Z-Wave Settings\n\n4. Select Add To A Z-Wave Network\n\n5. Put the controller into inclusion mode and select My Hub is in Inclusion Mode on the August app",
-		"exclusion": "In order to exclude the August Smart Lock from a Z-Wave network the user will have to do the following:\n1. Open the August app\n2. Go to the Lock Settings screen\n3. Select Z-Wave Settings\n4. Select Remove Z-Wave Device\n5. Put the controller into exclusion mode and select My Hub is in Exlusion Mode on the August app",
+		"exclusion": "In order to exclude the August Smart Lock from a Z-Wave network the user will have to do the following:\n1. Open the August app\n2. Go to the Lock Settings screen\n3. Select Z-Wave Settings\n4. Select Remove Z-Wave Device\n5. Put the controller into exclusion mode and select My Hub is in Exclusion Mode on the August app",
 		"reset": "In order to reset the August Smart Lock the user will have to do the following:\n\n1. Open the August app\n\n2. Go to the Lock Settings screen\n\n3. Select Z-Wave Settings\n\n4. Select Remove Z-Wave device\n\n5. Select My Hub Is No Longer Working\n\n6. Caution: Resetting a Z-Wave device without telling the hub can cause performance issues. Use this procedure only when the Z-Wave hub is missing or otherwise inoperable. \n\n7. Select Reset Z-Wave Device\n\n8. On the Reset Z-Wave Device? prompt select Reset",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2624/August%20Z-Wave%20Required%20Documentation.pdf",
 		"comments": {

package/config/devices/0x0346/alarm_keypad_gen1.json

@@ -134,7 +134,7 @@
 		{
 			"#": "11",
 			"label": "Ambient Light Sensor Level",
-			"description": "Light threshold where keypad will stop backlighting if higher than choosen value",
+			"description": "Light threshold where keypad will stop backlighting if higher than chosen value",
 			"valueSize": 1,
 			"minValue": 0,
 			"maxValue": 100,

package/config/devices/0x034e/mtbas-100-wl.json

@@ -2,7 +2,7 @@
 	"manufacturer": "TEM AG",
 	"manufacturerId": "0x034e",
 	"label": "MTBAS-100-WL",
-	"description": "Radio Base Modul",
+	"description": "Radio Base Module",
 	"devices": [
 		{
 			"productType": "0x0001",

package/config/devices/0x0371/zwa008.json

@@ -118,8 +118,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Tripple clicking the tamper button includes (adds) the device",
-		"exclusion": "Tripple clicking the tamper button excludes (removes) the device",
+		"inclusion": "Triple clicking the tamper button includes (adds) the device",
+		"exclusion": "Triple clicking the tamper button excludes (removes) the device",
 		"reset": "This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.\nOnce Cover is removed and tamper switch is tripped, push the tamper for 5 seconds until red LED blinks. Then release tamper and push it again for 5 seconds until LED blinks",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3472/User%20manual%20-%20Aeotec%20Door%20Window%20Sensor%207%20ZWA008.pdf"
 	}

package/config/devices/0x0371/zwa009_0.0_1.255.json

@@ -67,7 +67,7 @@
 		},
 		{
 			"#": "2",
-			"label": "Humidity Change Report Threshhold",
+			"label": "Humidity Change Report Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -100,7 +100,7 @@
 		},
 		{
 			"#": "5",
-			"label": "High Temperature Basic Set Threshhold",
+			"label": "High Temperature Basic Set Threshold",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
 			"valueSize": 2,
@@ -126,7 +126,7 @@
 		},
 		{
 			"#": "6",
-			"label": "Low Temperature Basic Set Threshhold",
+			"label": "Low Temperature Basic Set Threshold",
 			"description": "Allowable Range: 200-1000.",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
@@ -153,7 +153,7 @@
 		},
 		{
 			"#": "7",
-			"label": "High Humidity Basic Set Threshhold",
+			"label": "High Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -179,7 +179,7 @@
 		},
 		{
 			"#": "8",
-			"label": "Low Humidity Basic Set Threshhold",
+			"label": "Low Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,

package/config/devices/0x0371/zwa009_11.0_255.255.json

@@ -67,7 +67,7 @@
 		},
 		{
 			"#": "2",
-			"label": "Humidity Change Report Threshhold",
+			"label": "Humidity Change Report Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -100,7 +100,7 @@
 		},
 		{
 			"#": "5",
-			"label": "High Temperature Basic Set Threshhold",
+			"label": "High Temperature Basic Set Threshold",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
 			"valueSize": 2,
@@ -126,7 +126,7 @@
 		},
 		{
 			"#": "6",
-			"label": "Low Temperature Basic Set Threshhold",
+			"label": "Low Temperature Basic Set Threshold",
 			"description": "Allowable Range: 200-1000.",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
@@ -153,7 +153,7 @@
 		},
 		{
 			"#": "7",
-			"label": "High Humidity Basic Set Threshhold",
+			"label": "High Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -179,7 +179,7 @@
 		},
 		{
 			"#": "8",
-			"label": "Low Humidity Basic Set Threshhold",
+			"label": "Low Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,

package/config/devices/0x0371/zwa011.json

@@ -127,8 +127,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "Tripple clicking the tamper button includes (adds) the device",
-		"exclusion": "Tripple clicking the tamper button excludes (removes) the device",
+		"inclusion": "Triple clicking the tamper button includes (adds) the device",
+		"exclusion": "Triple clicking the tamper button excludes (removes) the device",
 		"reset": "This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.\nOnce Cover is removed and tamper switch is tripped, push the tamper for 5 seconds until red LED blinks. Then release tamper and push it again for 5 seconds until LED blinks",
 		"manual": "https://help.aeotec.com/support/solutions/articles/6000230382-door-window-sensor-7-basic-user-guide-zwa011-zwa041-"
 	}

package/config/devices/0x0371/zwa022.json

@@ -29,7 +29,7 @@
 			"maxNodes": 5
 		},
 		"4": {
-			"label": "Buttom Button set On/Off",
+			"label": "Bottom Button set On/Off",
 			"maxNodes": 5
 		},
 		"5": {
@@ -163,7 +163,7 @@
 	"metadata": {
 		"inclusion": "1. Turn your Z-Wave gateway/ controller into adding mode.\n2. Tap once the top/ bottom button, then the device will enter pairing mode",
 		"exclusion": "1. Turn your Z-Wave gateway/ controller into removing mode.\n2. Tap 6 times the top/ bottom button, then the device will enter exclusion mode",
-		"reset": "Press and hold the top/buttom button for 20s",
+		"reset": "Press and hold the top/bottom button for 20s",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4253/Aeotec%20WallMote%207%20manual.pdf"
 	}
 }

package/config/devices/0x0371/zwa037.json

@@ -29,7 +29,7 @@
 			"maxNodes": 5
 		},
 		"4": {
-			"label": "Buttom Button - Basic Set",
+			"label": "Bottom Button - Basic Set",
 			"maxNodes": 5
 		},
 		"5": {

package/config/devices/0x0371/zwa038.json

@@ -25,7 +25,7 @@
 			"maxNodes": 5
 		},
 		"3": {
-			"label": "Buttom Button - Basic Set",
+			"label": "Bottom Button - Basic Set",
 			"maxNodes": 5
 		},
 		"4": {
@@ -107,8 +107,8 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Turn your primary controller into inclusion mode.\n2. Press the Top/Buttom button once on product",
-		"exclusion": "1. Turn your primary controller into exclusion mode.\n2. 3*tap the Top/Buttom button on product",
+		"inclusion": "1. Turn your primary controller into inclusion mode.\n2. Press the Top/Bottom button once on product",
+		"exclusion": "1. Turn your primary controller into exclusion mode.\n2. 3*tap the Top/Bottom button on product",
 		"reset": "Press and hold the Top/ Bottom button for 20s",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4273/Aeotec%20Wall%20Switch%20manual.pdf"
 	}

package/config/devices/0x0371/zwa039.json

@@ -67,7 +67,7 @@
 		},
 		{
 			"#": "2",
-			"label": "Humidity Change Report Threshhold",
+			"label": "Humidity Change Report Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -110,7 +110,7 @@
 		},
 		{
 			"#": "5",
-			"label": "High Temperature Basic Set Threshhold",
+			"label": "High Temperature Basic Set Threshold",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
 			"valueSize": 2,
@@ -136,7 +136,7 @@
 		},
 		{
 			"#": "6",
-			"label": "Low Temperature Basic Set Threshhold",
+			"label": "Low Temperature Basic Set Threshold",
 			"description": "Allowable Range: 200-1000.",
 			"unit": "0.1 °(C/F)",
 			"unsigned": true,
@@ -163,7 +163,7 @@
 		},
 		{
 			"#": "7",
-			"label": "High Humidity Basic Set Threshhold",
+			"label": "High Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,
@@ -199,7 +199,7 @@
 		},
 		{
 			"#": "8",
-			"label": "Low Humidity Basic Set Threshhold",
+			"label": "Low Humidity Basic Set Threshold",
 			"unit": "%",
 			"unsigned": true,
 			"valueSize": 1,

package/config/devices/0x041b/39446_zw3107.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39446 / ZW3107",
-	"description": "Plug-in Dimmer (Dual Plug Simultaneous Control)",
+	"description": "Plug-in 2-Outlet Dimmer, Simultaneous, 500S",
 	"devices": [
 		{
 			"productType": "0x5044",
@@ -88,7 +88,7 @@
 			"label": "Dim Rate Timing (From Z-Wave Controller)",
 			"description": "Timing of steps",
 			"valueSize": 2,
-			"units": "10ms",
+			"unit": "10ms",
 			"minValue": 1,
 			"maxValue": 255,
 			"defaultValue": 1,
@@ -109,7 +109,7 @@
 			"label": "Dim Rate Timing (When Manually Controlled)",
 			"description": "Timing of steps",
 			"valueSize": 2,
-			"units": "10ms",
+			"unit": "10ms",
 			"minValue": 1,
 			"maxValue": 255,
 			"defaultValue": 1,
@@ -130,7 +130,7 @@
 			"label": "Dim Rate Timing (All-On/Off Command)",
 			"description": "Timing of steps",
 			"valueSize": 2,
-			"units": "10ms",
+			"unit": "10ms",
 			"minValue": 1,
 			"maxValue": 255,
 			"defaultValue": 1,

package/config/devices/0x041b/39449_zw4106.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39449 / ZW4106",
-	"description": "Plug-in Switch (Dual Plug Simultaneous Control)",
+	"description": "Plug-in 2-Outlet Switch, Simultaneous, 500S",
 	"devices": [
 		{
 			"productType": "0x5052",

package/config/devices/0x041b/39453_zw4203.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39453 / ZW4203",
-	"description": "Plug-in Outdoor Smart Switch",
+	"description": "Plug-in Outdoor Switch V2, 500S",
 	"devices": [
 		{
 			"productType": "0x4f50",

package/config/devices/0x041b/39455_zw4008.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39455 / ZW4008",
-	"description": "In-Wall Smart Switch",
+	"description": "In-Wall Paddle Switch, QFSW, 500S",
 	"devices": [
 		{
 			"productType": "0x4952",

package/config/devices/0x041b/39456_zw1002.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39456 / ZW1002",
-	"description": "In-Wall Tamper Resistant Outlet",
+	"description": "In-Wall Outlet, Tamper Resistant, 500S",
 	"devices": [
 		{
 			"productType": "0x4952",

package/config/devices/0x041b/39458_zw3010.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Resideo",
 	"manufacturerId": "0x041b",
 	"label": "39458 / ZW3010",
-	"description": "In-Wall Smart Dimmer",
+	"description": "In-Wall Paddle Dimmer, QFSW, 500S",
 	"devices": [
 		{
 			"productType": "0x4944",

package/config/devices/0x0433/q-light_puck.json

@@ -108,7 +108,7 @@
 		{
 			"#": "8",
 			"label": "Switch type",
-			"description": "Choose between momentary, ON/OFF and roller blind switch. Available settings: 0 – momentary (Push) switch. 1 – ON/OFF switch. 2– roller blind switch-two switchs operate the device(S1 to brighter, S2 to dim",
+			"description": "Choose between momentary, ON/OFF and roller blind switch. Available settings: 0 – momentary (Push) switch. 1 – ON/OFF switch. 2– roller blind switch-two switches operate the device(S1 to brighter, S2 to dim",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"unsigned": true,
@@ -123,7 +123,7 @@
 					"value": 1
 				},
 				{
-					"label": "roller blind switch-two switchs operate the device(S1 to brighter, S2 to dim)",
+					"label": "roller blind switch-two switches operate the device(S1 to brighter, S2 to dim)",
 					"value": 2
 				}
 			]
@@ -131,7 +131,7 @@
 		{
 			"#": "9",
 			"label": "Switch functionality of S1 and S2",
-			"description": "Set the desired value from 0 to 1 to turn on/off the memory function.Setting this value to 0 turns off the dimmer's Memory fucntion.Setting this value to 1 truns on the dimmer's Memory function.",
+			"description": "Set the desired value from 0 to 1 to turn on/off the memory function. Setting this value to 0 turns off the dimmer's Memory function. Setting this value to 1 turns on the dimmer's Memory function.",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"unsigned": true,

package/config/devices/0x0438/200w dimmer.json

@@ -109,7 +109,7 @@
 					"value": 0
 				},
 				{
-					"label": "Logaritmic",
+					"label": "Logarithmic",
 					"value": 1
 				}
 			]
@@ -145,7 +145,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Tripple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The purple indicator light will stay solid on for 10 seconds to indicate successful incusion.",
+		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Triple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The purple indicator light will stay solid on for 10 seconds to indicate successful incusion.",
 		"exclusion": "1. Set the primary controller/gateway int exclusion mode (Please refer top your primary controllers manual on how to set your controller into exclusion). 2.Triple press the reset button, the dimmer will be set to exclusion mode, and wait to be excluded, then the dimmer will be excluded form the network.",
 		"reset": "Press and hold down the reset button for over 5 seconds, the dimmer will be reset to factory defaults."
 	}

package/config/devices/0x0438/dimmer-400w.json

@@ -115,7 +115,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Tripple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The connected light will stay solid on for 3 seconds to indicate successful incusion.",
+		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Triple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The connected light will stay solid on for 3 seconds to indicate successful incusion.",
 		"exclusion": "1. Set the primary controller/gateway int exclusion mode (Please refer top your primary controllers manual on how to set your controller into exclusion). 2.Triple press the reset button, the dimmer will be set to exclusion mode, and wait to be excluded, then the dimmer will be excluded form the network.",
 		"reset": "Press and hold down the reset button for over 10 seconds, the dimmer will be reset to factory defaults."
 	}

package/config/devices/0x0438/dimmer2-400w.json

@@ -170,7 +170,7 @@
 		{
 			"#": "13",
 			"label": "Over Current Protection",
-			"description": "Must be over 2.1A for 20 seconds continously",
+			"description": "Must be over 2.1A for 20 seconds continuously",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -292,7 +292,7 @@
 		}
 	],
 	"metadata": {
-		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Tripple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The connected light will stay solid on for 3 seconds to indicate successful incusion.",
+		"inclusion": "1. Set primary controller/gateway into inclusion mode (Please refer top your primary controllers manual on how to set your controller into inclusion). 2. Power on the in-wall dimmer. 3.Triple Press the reset button on the dimmer, it will set the dimmer into inclusion mode. The connected light will stay solid on for 3 seconds to indicate successful incusion.",
 		"exclusion": "1. Set the primary controller/gateway int exclusion mode (Please refer top your primary controllers manual on how to set your controller into exclusion). 2.Triple press the reset button, the dimmer will be set to exclusion mode, and wait to be excluded, then the dimmer will be excluded form the network.",
 		"reset": "Press and hold down the reset button for over 10 seconds, the dimmer will be reset to factory defaults."
 	}

package/config/devices/0x0456/homee-005.json

@@ -22,7 +22,7 @@
 		}
 	},
 	"metadata": {
-		"reset": "If the Z Wave cube is reset to factory defaults, all connected Z Wave devices will be removed, and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessar y after the reset to remove and add all of the nodes in the network.\nIf this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller",
+		"reset": "If the Z Wave cube is reset to factory defaults, all connected Z Wave devices will be removed, and the cube gets a new Home ID. If homee is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and add all of the nodes in the network.\nIf this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4271/homee_zwave_pdf-komprimiert.pdf"
 	}
 }

package/config/devices/0x5254/zts-110.json

@@ -45,7 +45,7 @@
 		},
 		{
 			"#": "2",
-			"label": "Differntial",
+			"label": "Differential",
 			"description": "Set Differential value from 1F/.5C to 4F/2.0C Available settings: 1 - 4",
 			"valueSize": 1,
 			"minValue": 1,