@matter/types 0.13.0-alpha.0-20250318-c1aa38b08 → 0.13.0-alpha.0-20250323-770919c6a

package/src/clusters/water-heater-management.ts

@@ -217,8 +217,8 @@ export namespace WaterHeaterManagement {
              * can be computed by taking the specific heat capacity of water (4182 J/kg °C) and by knowing the current
              * temperature of the water, the tank volume and target temperature.
              *
-             * For example, if the target temperature was 60°C, the current temperature was 20°C and the tank volume
-             * was 100L:
+             * For example, if the target temperature was 60°C, the current temperature was 20°C and the tank volume was
+             * 100L:
              *
              * Mass of water = 1kg per Litre
              *
@@ -243,9 +243,9 @@ export namespace WaterHeaterManagement {
              * For example, a direct electric immersion heating element can be close to 100% efficient, so the
              * electrical energy needed to heat the hot water is nearly the same as the EstimatedHeatEnergyRequired.
              * However some forms of heating, such as an air-source heat pump which extracts heat from ambient air,
-             * requires much less electrical energy to heat hot water. Heat pumps can be produce 3kWh of heat output
-             * for 1kWh of electrical energy input. The conversion between heat energy and electrical energy is outside
-             * the scope of this cluster.
+             * requires much less electrical energy to heat hot water. Heat pumps can be produce 3kWh of heat output for
+             * 1kWh of electrical energy input. The conversion between heat energy and electrical energy is outside the
+             * scope of this cluster.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 9.5.7.4
              */
@@ -259,27 +259,27 @@ export namespace WaterHeaterManagement {
     export const TankPercentComponent = MutableCluster.Component({
         attributes: {
             /**
-             * Indicates an approximate level of hot water stored in the tank, which might help consumers understand
-             * the amount of hot water remaining in the tank. The accuracy of this attribute is manufacturer specific.
+             * Indicates an approximate level of hot water stored in the tank, which might help consumers understand the
+             * amount of hot water remaining in the tank. The accuracy of this attribute is manufacturer specific.
              *
              * In most hot water tanks, there is a stratification effect where the hot water layer rests above a cooler
-             * layer of water below. For this reason cold water is fed in at the bottom of the tank and the hot water
-             * is drawn from the top.
+             * layer of water below. For this reason cold water is fed in at the bottom of the tank and the hot water is
+             * drawn from the top.
              *
              * Some water tanks might use multiple temperature probes to estimate the level of the hot water layer. A
              * water heater with multiple temperature probes is likely to implement an algorithm to estimate the hot
-             * water tank percentage by taking into account the temperature values of each probe to determine the
-             * height of the hot water.
+             * water tank percentage by taking into account the temperature values of each probe to determine the height
+             * of the hot water.
              *
-             * However it might be possible with a single temperature probe to estimate how much hot water is left
-             * using a simpler algorithm:
+             * However it might be possible with a single temperature probe to estimate how much hot water is left using
+             * a simpler algorithm:
              *
              * For example, if the target temperature was 60°C, the CurrentTemperature was 40°C from a single
              * temperature probe measuring the average water temperature and the temperature of incoming cold water
              * (COLD_WATER_TEMP) was assumed to be 20°C:
              *
-             * TankPercentage = int(((current temperature - COLD_WATER_TEMP) / (target temperature - COLD_WATER_TEMP))
-             * * 100)
+             * TankPercentage = int(((current temperature - COLD_WATER_TEMP) / (target temperature - COLD_WATER_TEMP)) *
+             * 100)
              *
              * TankPercentage = min( max(TankPercentage,0), 100)
              *
@@ -395,8 +395,8 @@ export namespace WaterHeaterManagement {
     export const ClusterInstance = MutableCluster(Base);
 
     /**
-     * This cluster is used to allow clients to control the operation of a hot water heating appliance so that it can
-     * be used with energy management.
+     * This cluster is used to allow clients to control the operation of a hot water heating appliance so that it can be
+     * used with energy management.
      *
      * Heating of hot water is one of the main energy uses in homes, and when coupled with the Energy Management
      * cluster, it can help consumers save cost (e.g. using power at cheaper times or from local solar PV generation).
@@ -444,8 +444,8 @@ export namespace WaterHeaterManagement {
     /**
      * This cluster supports all WaterHeaterManagement features. It may support illegal feature combinations.
      *
-     * If you use this cluster you must manually specify which features are active and ensure the set of active
-     * features is legal per the Matter specification.
+     * If you use this cluster you must manually specify which features are active and ensure the set of active features
+     * is legal per the Matter specification.
      */
     export interface Complete extends Identity<typeof CompleteInstance> {}
 

package/src/clusters/water-heater-mode.ts

@@ -8,7 +8,7 @@
 
 import { MutableCluster } from "../cluster/mutation/MutableCluster.js";
 import { BitFlag } from "../schema/BitmapSchema.js";
-import { FixedAttribute, Attribute, Command, TlvNoResponse } from "../cluster/Cluster.js";
+import { FixedAttribute, Attribute, Command } from "../cluster/Cluster.js";
 import { TlvArray } from "../tlv/TlvArray.js";
 import { TlvField, TlvOptionalField, TlvObject } from "../tlv/TlvObject.js";
 import { TlvString } from "../tlv/TlvString.js";
@@ -101,8 +101,8 @@ export namespace WaterHeaterMode {
         Manual = 16385,
 
         /**
-         * While in modes with this tag, the device will attempt to keep the water warm based on the Schedules
-         * attribute of the associated Thermostat cluster.
+         * While in modes with this tag, the device will attempt to keep the water warm based on the Schedules attribute
+         * of the associated Thermostat cluster.
          *
          * @see {@link MatterSpecification.v13.Cluster} § 9.6.7.1.3
          */
@@ -170,9 +170,9 @@ export namespace WaterHeaterMode {
         mode: TlvField(1, TlvUInt8),
 
         /**
-         * This field shall contain a list of tags that are associated with the mode option. This may be used by
-         * clients to determine the full or the partial semantics of a certain mode, depending on which tags they
-         * understand, using standard definitions and/or manufacturer specific namespace definitions.
+         * This field shall contain a list of tags that are associated with the mode option. This may be used by clients
+         * to determine the full or the partial semantics of a certain mode, depending on which tags they understand,
+         * using standard definitions and/or manufacturer specific namespace definitions.
          *
          * The standard mode tags are defined in this cluster specification. For the derived cluster instances, if the
          * specification of the derived cluster defines a namespace, the set of standard mode tags also includes the
@@ -183,8 +183,8 @@ export namespace WaterHeaterMode {
          * the mode in an automation, or to craft help text their voice-driven interfaces. A mode tag shall be either a
          * standard tag or a manufacturer specific tag, as defined in each ModeTagStruct list entry.
          *
-         * A mode option may have more than one mode tag. A mode option may be associated with a mixture of standard
-         * and manufacturer specific mode tags. A mode option shall be associated with at least one standard mode tag.
+         * A mode option may have more than one mode tag. A mode option may be associated with a mixture of standard and
+         * manufacturer specific mode tags. A mode option shall be associated with at least one standard mode tag.
          *
          * A few examples are provided below.
          *
@@ -241,8 +241,8 @@ export namespace WaterHeaterMode {
              * At least one entry in the SupportedModes attribute shall include the Off mode tag in the ModeTags field
              * list.
              *
-             * An entry in the SupportedModes attribute that includes one of an Off, Manual, or Timed tag shall NOT
-             * also include an additional instance of any one of these tag types.
+             * An entry in the SupportedModes attribute that includes one of an Off, Manual, or Timed tag shall NOT also
+             * include an additional instance of any one of these tag types.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 9.6.6.1
              */
@@ -266,7 +266,7 @@ export namespace WaterHeaterMode {
              *
              * @see {@link MatterSpecification.v13.Cluster} § 1.10.7.1
              */
-            changeToMode: Command(0x0, ModeBase.TlvChangeToModeRequest, 0x0, TlvNoResponse)
+            changeToMode: Command(0x0, ModeBase.TlvChangeToModeRequest, 0x1, ModeBase.TlvChangeToModeResponse)
         },
 
         /**

package/src/clusters/water-tank-level-monitoring.ts

@@ -32,8 +32,8 @@ export namespace WaterTankLevelMonitoring {
     /**
      * This cluster supports all WaterTankLevelMonitoring features. It may support illegal feature combinations.
      *
-     * If you use this cluster you must manually specify which features are active and ensure the set of active
-     * features is legal per the Matter specification.
+     * If you use this cluster you must manually specify which features are active and ensure the set of active features
+     * is legal per the Matter specification.
      */
     export const CompleteInstance = MutableCluster({
         ...ResourceMonitoring.Complete,

package/src/clusters/wi-fi-network-diagnostics.ts

@@ -244,8 +244,8 @@ export namespace WiFiNetworkDiagnostics {
         attributes: {
             /**
              * The BeaconLostCount attribute shall indicate the count of the number of missed beacons the Node has
-             * detected. If the Node does not have an ability to count beacons expected and not received, this value
-             * may remain set to zero.
+             * detected. If the Node does not have an ability to count beacons expected and not received, this value may
+             * remain set to zero.
              *
              * @see {@link MatterSpecification.v13.Core} § 11.15.6.6
              */
@@ -253,8 +253,8 @@ export namespace WiFiNetworkDiagnostics {
 
             /**
              * The OverrunCount attribute shall indicate the number of packets dropped either at ingress or egress, due
-             * to lack of buffer memory to retain all packets on the network interface. The OverrunCount attribute
-             * shall be reset to 0 upon a reboot of the Node.
+             * to lack of buffer memory to retain all packets on the network interface. The OverrunCount attribute shall
+             * be reset to 0 upon a reboot of the Node.
              *
              * @see {@link MatterSpecification.v13.Core} § 11.15.6.13
              */
@@ -293,8 +293,8 @@ export namespace WiFiNetworkDiagnostics {
             /**
              * The BeaconRxCount attribute shall indicate the count of the number of received beacons. The total number
              * of expected beacons that could have been received during the interval since association SHOULD match the
-             * sum of BeaconRxCount and BeaconLostCount. If the Node does not have an ability to report count of
-             * beacons received, this value may remain set to zero.
+             * sum of BeaconRxCount and BeaconLostCount. If the Node does not have an ability to report count of beacons
+             * received, this value may remain set to zero.
              *
              * @see {@link MatterSpecification.v13.Core} § 11.15.6.7
              */
@@ -427,9 +427,9 @@ export namespace WiFiNetworkDiagnostics {
             associationFailure: OptionalEvent(0x1, EventPriority.Info, TlvAssociationFailureEvent),
 
             /**
-             * The ConnectionStatus Event shall indicate that a Node’s connection status to a Wi-Fi network has
-             * changed. Connected, in this context, shall mean that a Node acting as a Wi-Fi station is successfully
-             * associated to a Wi-Fi Access Point.
+             * The ConnectionStatus Event shall indicate that a Node’s connection status to a Wi-Fi network has changed.
+             * Connected, in this context, shall mean that a Node acting as a Wi-Fi station is successfully associated
+             * to a Wi-Fi Access Point.
              *
              * @see {@link MatterSpecification.v13.Core} § 11.15.8.3
              */
@@ -521,8 +521,8 @@ export namespace WiFiNetworkDiagnostics {
     /**
      * This cluster supports all WiFiNetworkDiagnostics features. It may support illegal feature combinations.
      *
-     * If you use this cluster you must manually specify which features are active and ensure the set of active
-     * features is legal per the Matter specification.
+     * If you use this cluster you must manually specify which features are active and ensure the set of active features
+     * is legal per the Matter specification.
      */
     export interface Complete extends Identity<typeof CompleteInstance> {}
 

package/src/clusters/wi-fi-network-management.ts

@@ -13,10 +13,28 @@ import { TlvNullable } from "../tlv/TlvNullable.js";
 import { TlvUInt64 } from "../tlv/TlvNumber.js";
 import { AccessLevel } from "#model";
 import { TlvNoArguments } from "../tlv/TlvNoArguments.js";
+import { TlvField, TlvObject } from "../tlv/TlvObject.js";
+import { TypeFromSchema } from "../tlv/TlvSchema.js";
 import { Identity } from "#general";
 import { ClusterRegistry } from "../cluster/ClusterRegistry.js";
 
 export namespace WiFiNetworkManagement {
+    /**
+     * This command shall be generated in response to a NetworkPassphraseRequest command.
+     *
+     * @see {@link MatterSpecification.v13.Cluster} § 10.2.5.2
+     */
+    export const TlvNetworkPassphraseResponse = TlvObject({
+        passphrase: TlvField(0, TlvByteString.bound({ maxLength: 64 }))
+    });
+
+    /**
+     * This command shall be generated in response to a NetworkPassphraseRequest command.
+     *
+     * @see {@link MatterSpecification.v13.Cluster} § 10.2.5.2
+     */
+    export interface NetworkPassphraseResponse extends TypeFromSchema<typeof TlvNetworkPassphraseResponse> {}
+
     /**
      * @see {@link Cluster}
      */
@@ -29,15 +47,15 @@ export namespace WiFiNetworkManagement {
             /**
              * Indicates the SSID of the primary Wi-Fi network provided by this device.
              *
-             * A value of null shall indicate that no primary Wi-Fi network is available (e.g. because the Wi-Fi
-             * network has not yet been configured by the user).
+             * A value of null shall indicate that no primary Wi-Fi network is available (e.g. because the Wi-Fi network
+             * has not yet been configured by the user).
              *
              * NOTE
              *
              * The SSID in Wi-Fi is a collection of 1-32 bytes, the text encoding of which is not specified.
-             * Implementations must be careful to support transferring these byte strings without requiring a
-             * particular encoding. The most common encoding is UTF-8, however this is just a convention. Some
-             * configurations may use Latin-1 or other character sets.
+             * Implementations must be careful to support transferring these byte strings without requiring a particular
+             * encoding. The most common encoding is UTF-8, however this is just a convention. Some configurations may
+             * use Latin-1 or other character sets.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 10.2.4.1
              */
@@ -62,8 +80,8 @@ export namespace WiFiNetworkManagement {
              * NOTE
              *
              * The passphrase itself is not exposed as an attribute to avoid its unintentional retrieval or caching by
-             * clients that use wildcard reads or otherwise routinely read all available attributes. It can be
-             * retrieved using the NetworkPassphraseRequest
+             * clients that use wildcard reads or otherwise routinely read all available attributes. It can be retrieved
+             * using the NetworkPassphraseRequest
              *
              * command.
              *
@@ -84,8 +102,8 @@ export namespace WiFiNetworkManagement {
              * If the command is not executed via a CASE session, the command shall be rejected with a status of
              * UNSUPPORTED_ACCESS.
              *
-             * If no primary Wi-Fi network is available (the SSID attribute is null), the command shall be rejected
-             * with a status of INVALID_IN_STATE.
+             * If no primary Wi-Fi network is available (the SSID attribute is null), the command shall be rejected with
+             * a status of INVALID_IN_STATE.
              *
              * Otherwise a NetworkPassphraseResponse shall be generated.
              *
@@ -95,7 +113,7 @@ export namespace WiFiNetworkManagement {
                 0x0,
                 TlvNoArguments,
                 0x1,
-                TlvNoArguments,
+                TlvNetworkPassphraseResponse,
                 { invokeAcl: AccessLevel.Manage }
             )
         }
@@ -103,8 +121,8 @@ export namespace WiFiNetworkManagement {
 
     /**
      * This cluster provides an interface for getting information about the Wi-Fi network that a Network Infrastructure
-     * Manager device type provides. Privileged nodes within the same fabric as a Network Infrastructure Manager can
-     * use these interfaces to request information related to the Wi-Fi Network such as SSID and Passphrase.
+     * Manager device type provides. Privileged nodes within the same fabric as a Network Infrastructure Manager can use
+     * these interfaces to request information related to the Wi-Fi Network such as SSID and Passphrase.
      *
      * @see {@link MatterSpecification.v13.Cluster} § 10.2
      */

package/src/clusters/window-covering.ts

@@ -560,8 +560,8 @@ export namespace WindowCovering {
         remoteLockout: BitFlag(0),
 
         /**
-         * Tampering detected on sensors or any other safety equipment. Ex: a device has been forcedly moved without
-         * its actuator(s).
+         * Tampering detected on sensors or any other safety equipment. Ex: a device has been forcedly moved without its
+         * actuator(s).
          */
         tamperDetection: BitFlag(1),
 
@@ -625,8 +625,8 @@ export namespace WindowCovering {
     export const LiftAndPositionAwareLiftAndAbsolutePositionComponent = MutableCluster.Component({
         attributes: {
             /**
-             * Indicates the maximum possible encoder position possible (Unit cm, centimeters) to position the height
-             * of the window covering lift.
+             * Indicates the maximum possible encoder position possible (Unit cm, centimeters) to position the height of
+             * the window covering lift.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.6.2
              */
@@ -735,8 +735,8 @@ export namespace WindowCovering {
              *
              * If the server does not support the PositionAware feature, then a zero percentage shall be treated as a
              * UpOrOpen command and a non-zero percentage shall be treated as an DownOrClose command. If the device is
-             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD
-             * be returned.
+             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD be
+             * returned.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.7.5
              */
@@ -760,8 +760,8 @@ export namespace WindowCovering {
 
         commands: {
             /**
-             * Upon receipt of this command, the server will adjust the window covering to the tilt percentage
-             * specified in the payload of this command.
+             * Upon receipt of this command, the server will adjust the window covering to the tilt percentage specified
+             * in the payload of this command.
              *
              * If the command includes TiltPercent100thsValue, then TargetPositionTiltPercent100ths attribute shall be
              * set to TiltPercent100thsValue. Otherwise the TargetPositionTiltPercent100ths attribute shall be set to
@@ -773,8 +773,8 @@ export namespace WindowCovering {
              *
              * If the server does not support the PositionAware feature, then a zero percentage shall be treated as a
              * UpOrOpen command and a non-zero percentage shall be treated as an DownOrClose command. If the device is
-             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD
-             * be returned.
+             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD be
+             * returned.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.7.7
              */
@@ -834,8 +834,8 @@ export namespace WindowCovering {
              *
              * If the server does not support the PositionAware feature, then a zero percentage shall be treated as a
              * UpOrOpen command and a non-zero percentage shall be treated as an DownOrClose command. If the device is
-             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD
-             * be returned.
+             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD be
+             * returned.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.7.5
              */
@@ -882,8 +882,8 @@ export namespace WindowCovering {
 
         commands: {
             /**
-             * Upon receipt of this command, the server will adjust the window covering to the tilt percentage
-             * specified in the payload of this command.
+             * Upon receipt of this command, the server will adjust the window covering to the tilt percentage specified
+             * in the payload of this command.
              *
              * If the command includes TiltPercent100thsValue, then TargetPositionTiltPercent100ths attribute shall be
              * set to TiltPercent100thsValue. Otherwise the TargetPositionTiltPercent100ths attribute shall be set to
@@ -895,8 +895,8 @@ export namespace WindowCovering {
              *
              * If the server does not support the PositionAware feature, then a zero percentage shall be treated as a
              * UpOrOpen command and a non-zero percentage shall be treated as an DownOrClose command. If the device is
-             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD
-             * be returned.
+             * only a tilt control device, then the command SHOULD be ignored and a UNSUPPORTED_COMMAND status SHOULD be
+             * returned.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.7.7
              */
@@ -967,8 +967,8 @@ export namespace WindowCovering {
             /**
              * AbsolutePosition
              *
-             * The percentage attributes shall indicate the position as a percentage between the InstalledOpenLimits
-             * and InstalledClosedLimits attributes of the window covering starting at the open (0.00%).
+             * The percentage attributes shall indicate the position as a percentage between the InstalledOpenLimits and
+             * InstalledClosedLimits attributes of the window covering starting at the open (0.00%).
              *
              * As a general rule, absolute positioning (in centimeters or tenth of a degrees) SHOULD NOT be supported
              * for new implementations.
@@ -1022,13 +1022,13 @@ export namespace WindowCovering {
 
             /**
              * The Mode attribute allows configuration of the window covering, such as: reversing the motor direction,
-             * placing the window covering into calibration mode, placing the motor into maintenance mode, disabling
-             * the network, and disabling status LEDs.
+             * placing the window covering into calibration mode, placing the motor into maintenance mode, disabling the
+             * network, and disabling status LEDs.
              *
              * In the case a device does not support or implement a specific mode, e.g. the device has a specific
              * installation method and reversal is not relevant or the device does not include a maintenance mode, any
-             * write interaction to the Mode attribute, with an unsupported mode bit or any out of bounds bits set,
-             * must be ignored and a response containing the status of CONSTRAINT_ERROR will be returned.
+             * write interaction to the Mode attribute, with an unsupported mode bit or any out of bounds bits set, must
+             * be ignored and a response containing the status of CONSTRAINT_ERROR will be returned.
              *
              * @see {@link MatterSpecification.v13.Cluster} § 5.3.6.21
              */
@@ -1050,8 +1050,8 @@ export namespace WindowCovering {
 
         commands: {
             /**
-             * Upon receipt of this command, the window covering will adjust its position so the physical lift/slide
-             * and tilt is at the maximum open/up position. This will happen as fast as possible. The server attributes
+             * Upon receipt of this command, the window covering will adjust its position so the physical lift/slide and
+             * tilt is at the maximum open/up position. This will happen as fast as possible. The server attributes
              * shall be updated as follows:
              *
              * if the PositionAware feature is supported:
@@ -1060,8 +1060,8 @@ export namespace WindowCovering {
              *
              *   • TargetPositionTiltPercent100ths attribute shall be set to 0.00%.
              *
-             * The server positioning attributes will follow the movements, once the movement has successfully
-             * finished, the server attributes shall be updated as follows:
+             * The server positioning attributes will follow the movements, once the movement has successfully finished,
+             * the server attributes shall be updated as follows:
              *
              * if the PositionAware feature is supported:
              *
@@ -1082,9 +1082,9 @@ export namespace WindowCovering {
             upOrOpen: Command(0x0, TlvNoArguments, 0x0, TlvNoResponse),
 
             /**
-             * Upon receipt of this command, the window covering will adjust its position so the physical lift/slide
-             * and tilt is at the maximum closed/down position. This will happen as fast as possible. The server
-             * attributes supported shall be updated as follows:
+             * Upon receipt of this command, the window covering will adjust its position so the physical lift/slide and
+             * tilt is at the maximum closed/down position. This will happen as fast as possible. The server attributes
+             * supported shall be updated as follows:
              *
              * if the PositionAware feature is supported:
              *
@@ -1092,8 +1092,8 @@ export namespace WindowCovering {
              *
              *   • TargetPositionTiltPercent100ths attribute shall be set to 100.00%.
              *
-             * The server positioning attributes will follow the movements, once the movement has successfully
-             * finished, the server attributes shall be updated as follows:
+             * The server positioning attributes will follow the movements, once the movement has successfully finished,
+             * the server attributes shall be updated as follows:
              *
              * if the PositionAware feature is supported:
              *
@@ -1280,8 +1280,8 @@ export namespace WindowCovering {
     /**
      * This cluster supports all WindowCovering features. It may support illegal feature combinations.
      *
-     * If you use this cluster you must manually specify which features are active and ensure the set of active
-     * features is legal per the Matter specification.
+     * If you use this cluster you must manually specify which features are active and ensure the set of active features
+     * is legal per the Matter specification.
      */
     export interface Complete extends Identity<typeof CompleteInstance> {}
 

package/src/common/StatusCode.ts

@@ -26,3 +26,6 @@ export class StatusResponseError extends MatterError {
         return error instanceof StatusResponseError && (!codes.length || codes.includes(error.code));
     }
 }
+
+/** Error class for Status response errors that were received from the other node. */
+export class ReceivedStatusResponseError extends StatusResponseError {}

package/src/globals/Locationdesc.ts

@@ -24,8 +24,8 @@ export const TlvLocationdesc = TlvObject({
      * This field shall indicate the name of the location. For example, "blue room".
      *
      * If the location name is not user provided, the logic that generates it (clients, devices etc.) SHOULD utilize
-     * synthesized user-friendly, understandable, names for the location, rather than opaque values such as "private"
-     * or "2fe7c241-a50a-4863-896e-c5878da5ed68".
+     * synthesized user-friendly, understandable, names for the location, rather than opaque values such as "private" or
+     * "2fe7c241-a50a-4863-896e-c5878da5ed68".
      *
      * @see {@link MatterSpecification.v13.Core} § 7.19.2.45.1
      */
@@ -34,8 +34,8 @@ export const TlvLocationdesc = TlvObject({
     /**
      * This field shall indicate the level number. Negative values correspond to basement levels.
      *
-     * Value zero indicates this is the main floor, which typically includes the main entrance to the user’s home. For
-     * a building with multiple levels, it is the client’s responsibility to map each level to/from a FloorNumber tag
+     * Value zero indicates this is the main floor, which typically includes the main entrance to the user’s home. For a
+     * building with multiple levels, it is the client’s responsibility to map each level to/from a FloorNumber tag
      * value, using the level numbering convention of the region where the client operates. For example, if the client
      * operates in Europe, building level 1, which is one level up from the street level, SHOULD be mapped to
      * FloorNumber tag value 0x1. If the client operates in North America, building level 1, which is at street level,
@@ -44,14 +44,14 @@ export const TlvLocationdesc = TlvObject({
      * A null value indicates that this information is not available.
      *
      * When the clients present the level information for user selection, they SHOULD use the operating region to
-     * determine how to render and map this data. For example, if the client operates in North America it SHOULD
-     * present the user a list that includes entries labeled "basement", "first", "second", and internally mapped to
-     * floor numbers -1, 0, and 1. If operating in Europe, the client SHOULD present a list that includes entries
-     * labeled "basement", "ground", "first", internally mapped to floor numbers -1, 0, and 1.
+     * determine how to render and map this data. For example, if the client operates in North America it SHOULD present
+     * the user a list that includes entries labeled "basement", "first", "second", and internally mapped to floor
+     * numbers -1, 0, and 1. If operating in Europe, the client SHOULD present a list that includes entries labeled
+     * "basement", "ground", "first", internally mapped to floor numbers -1, 0, and 1.
      *
-     * The floor number information is expected to be mostly useful to the clients, rather than the devices, such as
-     * for grouping devices that are located on the same level. For example, an automation may be defined for all
-     * devices located at the basement level (floor number -1).
+     * The floor number information is expected to be mostly useful to the clients, rather than the devices, such as for
+     * grouping devices that are located on the same level. For example, an automation may be defined for all devices
+     * located at the basement level (floor number -1).
      *
      * NOTE
      *
@@ -70,8 +70,8 @@ export const TlvLocationdesc = TlvObject({
      *
      * NOTE
      *
-     * This field only indicates the type of the area. Multiple areas of the same type, such as bedrooms, may exist in
-     * a user’s home.
+     * This field only indicates the type of the area. Multiple areas of the same type, such as bedrooms, may exist in a
+     * user’s home.
      *
      * @see {@link MatterSpecification.v13.Core} § 7.19.2.45.3
      */

package/src/globals/MeasurementAccuracy.ts

@@ -48,9 +48,9 @@ export const TlvMeasurementAccuracy = TlvObject({
      * The value of the RangeMax field on the last MeasurementAccuracyRangeStruct in this list shall be less than or
      * equal to the value of the MaxMeasuredValue field.
      *
-     * The value of the RangeMin field on each MeasurementAccuracyRangeStruct in this list other than the first shall
-     * be one more the value of the RangeMax field on the previous MeasurementAccuracyRangeStruct in this list (i.e.
-     * there shall be no gaps in the accuracy ranges, and the ranges shall be in increasing order).
+     * The value of the RangeMin field on each MeasurementAccuracyRangeStruct in this list other than the first shall be
+     * one more the value of the RangeMax field on the previous MeasurementAccuracyRangeStruct in this list (i.e. there
+     * shall be no gaps in the accuracy ranges, and the ranges shall be in increasing order).
      *
      * @see {@link MatterSpecification.v13.Cluster} § 2.1.4.4.5
      */

package/src/globals/MeasurementAccuracyRange.ts

@@ -17,8 +17,8 @@ import { TypeFromSchema } from "../tlv/TlvSchema.js";
  *   • If both PercentMax and FixedMax are indicated, then for a given true value in the range between RangeMin and
  *     RangeMax,
  *
- *     ◦ the reported value shall be less than or equal to the sum of the true value, FixedMax and PercentMax percent
- *       of the true value.
+ *     ◦ the reported value shall be less than or equal to the sum of the true value, FixedMax and PercentMax percent of
+ *       the true value.
  *
  *     ◦ the reported value shall be greater than or equal to the true value minus the sum of FixedMax and PercentMax
  *       percent of the true value.
@@ -90,24 +90,24 @@ export const TlvMeasurementAccuracyRange = TlvObject({
     percentTypical: TlvOptionalField(4, TlvPercent100ths),
 
     /**
-     * This field shall indicate the maximum +/- fixed accuracy for the associated measurement, in the unit indicated
-     * by MeasurementType.
+     * This field shall indicate the maximum +/- fixed accuracy for the associated measurement, in the unit indicated by
+     * MeasurementType.
      *
      * @see {@link MatterSpecification.v13.Cluster} § 2.1.4.3.6
      */
     fixedMax: TlvOptionalField(5, TlvUInt64),
 
     /**
-     * This field shall indicate the minimum +/- fixed accuracy for the associated measurement, in the unit indicated
-     * by MeasurementType.
+     * This field shall indicate the minimum +/- fixed accuracy for the associated measurement, in the unit indicated by
+     * MeasurementType.
      *
      * @see {@link MatterSpecification.v13.Cluster} § 2.1.4.3.7
      */
     fixedMin: TlvOptionalField(6, TlvUInt64),
 
     /**
-     * This field shall indicate the typical +/- fixed accuracy for the associated measurement, in the unit indicated
-     * by MeasurementType.
+     * This field shall indicate the typical +/- fixed accuracy for the associated measurement, in the unit indicated by
+     * MeasurementType.
      *
      * @see {@link MatterSpecification.v13.Cluster} § 2.1.4.3.8
      */
@@ -121,8 +121,8 @@ export const TlvMeasurementAccuracyRange = TlvObject({
  *   • If both PercentMax and FixedMax are indicated, then for a given true value in the range between RangeMin and
  *     RangeMax,
  *
- *     ◦ the reported value shall be less than or equal to the sum of the true value, FixedMax and PercentMax percent
- *       of the true value.
+ *     ◦ the reported value shall be less than or equal to the sum of the true value, FixedMax and PercentMax percent of
+ *       the true value.
  *
  *     ◦ the reported value shall be greater than or equal to the true value minus the sum of FixedMax and PercentMax
  *       percent of the true value.

package/src/globals/Priority.ts

@@ -10,8 +10,8 @@
  * Priority
  *
  * This is an enumeration of priority used to tag events and possibly other data. The data type does not define any
- * particular ordering among the values. Specific uses of the data type may assign semantics to the values that imply
- * an ordering relationship.
+ * particular ordering among the values. Specific uses of the data type may assign semantics to the values that imply an
+ * ordering relationship.
  *
  * @see {@link MatterSpecification.v13.Core} § 7.19.2.17
  */

package/src/globals/Semtag.ts

@@ -67,7 +67,7 @@ export const TlvSemtag = TlvObject({
      * @see {@link MatterSpecification.v13.Core} § 7.19.2.42.4
      */
     label: TlvOptionalField(3, TlvNullable(TlvString.bound({ maxLength: 64 })))
-})
+});
 
 /**
  * Semantic Tag