@rdlabo/capacitor-brotherprint 6.0.3 → 6.2.0-0

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2125NPrintSettings.h

@@ -0,0 +1,83 @@
+//
+//  TD2125NPrintSettings.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
+
+
+@interface TD2125NPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>
+
+// These definitions are provided for information only. DO NOT MODIFY!
+#define TD2125N_RESOLUTION_HORZ 203
+#define TD2125N_RESOLUTION_VERT 203
+// spec section 2.3.5 Raster Line
+#define TD2125N_HEADSIZEDOTS 448
+// spec section "Select compression mode" command
+// NOTE: This should be same as HEADSIZEDOTS/8. And, it should be same as the # of decompressed bytes.
+#define TD2125N_MAX_COMPRESS_LENGTH 56
+
+// not in spec. Used Windows Printer Driver as reference.
+// NOTE: MAXPAPERWIDTH can exceed HEADSIZEDOTS!!
+#define TD2125N_MIN_PAPERWIDTHDOTS (0.47F * TD2125N_RESOLUTION_HORZ) // 95
+#define TD2125N_MAX_PAPERWIDTHDOTS (2.48F * TD2125N_RESOLUTION_VERT) // 503
+// spec section 2.3.4 Maximum and Minimum Lengths
+#define TD2125N_MIN_PAPERLENGTHDOTS 96
+#define TD2125N_MAX_PAPERLENGTHDOTS 7992
+// spec section 2.3.3 Feed Amount
+#ifdef OLD
+// IMPORTANT NOTE: For LABEL papertype ONLY, we allow the MIN marginlengthdots to be set to 0.
+// That is, this MIN value here is ignored when papertype = label is specified.
+// Consider the case of a 1.0x0.5" label. A min margin of 0.12" will take up half of the printable length!!
+// This is why we will allow the margin to be set to 0 in this case.
+// Beware that some labels might clip the top if this is set to 0. But, other settings can be tweaked to
+// make it work (such as by setting a larger paperlength and setting the top margin to non-zero.)
+#define TD2125N_MIN_MARGINLENGTHDOTS 24
+
+#else
+
+// Allow 0 now for continuous roll too, as the Esc iUw command generated from this can affect AirPrint.
+// However, if this is 0, then the Esc id command will send 0 too. And, the printer may not eject the page
+// enough at the end. So, I am introducing the MIN_PAGEFEEDDOTS definition now, so that if current marginLengthDots
+// is LESS than MIN_PAGEFEEDDOTS, we will send Esc id command using the MIN_PAGEFEEDDOTS value instead.
+// Otherwise, the Esc id command will use the marginLengthDots value as it has in the past.
+//
+// NOTE: If this occurs, the final paper length after tear off will be up to 1/4" longer than the
+// specified paperLengthDots, because the print data will be (up to) the entire paper length, and then the
+// PAGEFEEDDOTS will be added to the final paper length. If you need a specific paperlength, then make sure
+// that marginLengthDots is >= MIN_PAGEFEEDDOTS.
+
+#define TD2125N_MIN_MARGINLENGTHDOTS 0
+// v2.3.0 UPDATE: Instead of forcing this MIN_PAGEFEEDDOTS value on EVERY page, which essentially PREVENTS a "no gap"
+// solution if the FW actually supports it, now we only force it on the LAST page, allowing a 0-margin between pages
+// in case the FW allows it. But, we will force this on the LAST page, to assure the FW will eject the page to tear off
+// in case it doesn't automatically behave that way.
+#define TD2125N_MIN_PAGEFEEDDOTS_LASTPAGE 24
+
+#endif
+
+#define TD2125N_MAX_MARGINLENGTHDOTS 1015
+// Arbitrarily restrict extraFeed to 11" at 203 dpi. There is no reason to be larger.
+#define TD2125N_MAX_EXTRAFEEDDOTS (11*TD2125N_RESOLUTION_VERT)
+
+//*** IMPORTANT ***
+// SDK Users:
+// You should NEVER instantiate an object of the GenericMobileLabelModelPrintSettings superclass.
+// Instead, you should instantiate one of the model-specific subclasses (i.e. TD2125NPrintSettings).
+//
+// For a list of important properties in the settings that your application needs to set,
+// refer to the GenericMobileLabelModelPrintSettings superclass.
+
+// SDK Designers:
+// The GenericMobileLabelModelPrintSettings superclass handles all the important work.
+// This subclass only needs to provide the model-specific data to the generic class(es).
+
+//*** ADDITIONAL PROPERTIES not handled by GenericMobileLabelModelPrintSettings
+@property (nonatomic, assign) BOOL peelerEnabled;
+@property (nonatomic, assign) BOOL invert180degrees;
+
+
+@end

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2125NPrintSettingsViewController.h

@@ -0,0 +1,42 @@
+//
+//  TD2125NPrintSettingsViewController.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2125NPrintSettings.h>
+
+// This is the DEFAULT popup contentSize for TD2125NPrintSettingsViewController.
+//
+// You can override this by setting the "popoverSize" property (defined in the
+// PrintSettingsViewController superclass) to something different
+// before showing the ViewController.
+//
+// The popoverSize setting will be propagated to all of the "child" ViewControllers
+// of the main ViewController so all of the detail views will be the SAME size as each other.
+//
+// NOTE: iPad1 and iPad2 size = 1024 x 768, iPad3 = 2048 x 1536
+//#define TD2125NPOPUPCONTENTSIZE CGSizeMake(400,480)
+#define TD2125NPOPUPCONTENTSIZE CGSizeMake(400,548)
+#define TD2125NPOPUPCONTENTSIZE_IOS7 CGSizeMake(400,588)
+
+
+/*
+ This class is a subclass of GenericMobileLabelModelPrintSettingsViewController,
+ which implements all the major functionality.
+ 
+ *** SDK Users:  
+ DO NOT INSTANTIATE an instance of GenericMobileLabelModelPrintSettingsViewController.
+ Always instantiate a model-specific class, e.g. TD2125NPrintSettingsViewController
+ */
+
+@interface TD2125NPrintSettingsViewController : GenericMobileLabelModelPrintSettingsViewController
+{
+}
+
+@end
+
+

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2125NWBPrintSettings.h

@@ -0,0 +1,83 @@
+//
+//  TD2125NWBPrintSettings.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
+
+
+@interface TD2125NWBPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>
+
+// These definitions are provided for information only. DO NOT MODIFY!
+#define TD2125NWB_RESOLUTION_HORZ 203
+#define TD2125NWB_RESOLUTION_VERT 203
+// spec section 2.3.5 Raster Line
+#define TD2125NWB_HEADSIZEDOTS 448
+// spec section "Select compression mode" command
+// NOTE: This should be same as HEADSIZEDOTS/8. And, it should be same as the # of decompressed bytes.
+#define TD2125NWB_MAX_COMPRESS_LENGTH 56
+
+// not in spec. Used Windows Printer Driver as reference.
+// NOTE: MAXPAPERWIDTH can exceed HEADSIZEDOTS!!
+#define TD2125NWB_MIN_PAPERWIDTHDOTS (0.47F * TD2125NWB_RESOLUTION_HORZ) // 95
+#define TD2125NWB_MAX_PAPERWIDTHDOTS (2.48F * TD2125NWB_RESOLUTION_VERT) // 503
+// spec section 2.3.4 Maximum and Minimum Lengths
+#define TD2125NWB_MIN_PAPERLENGTHDOTS 96
+#define TD2125NWB_MAX_PAPERLENGTHDOTS 7992
+// spec section 2.3.3 Feed Amount
+#ifdef OLD
+// IMPORTANT NOTE: For LABEL papertype ONLY, we allow the MIN marginlengthdots to be set to 0.
+// That is, this MIN value here is ignored when papertype = label is specified.
+// Consider the case of a 1.0x0.5" label. A min margin of 0.12" will take up half of the printable length!!
+// This is why we will allow the margin to be set to 0 in this case.
+// Beware that some labels might clip the top if this is set to 0. But, other settings can be tweaked to
+// make it work (such as by setting a larger paperlength and setting the top margin to non-zero.)
+#define TD2125NWB_MIN_MARGINLENGTHDOTS 24
+
+#else
+
+// Allow 0 now for continuous roll too, as the Esc iUw command generated from this can affect AirPrint.
+// However, if this is 0, then the Esc id command will send 0 too. And, the printer may not eject the page
+// enough at the end. So, I am introducing the MIN_PAGEFEEDDOTS definition now, so that if current marginLengthDots
+// is LESS than MIN_PAGEFEEDDOTS, we will send Esc id command using the MIN_PAGEFEEDDOTS value instead.
+// Otherwise, the Esc id command will use the marginLengthDots value as it has in the past.
+//
+// NOTE: If this occurs, the final paper length after tear off will be up to 1/4" longer than the
+// specified paperLengthDots, because the print data will be (up to) the entire paper length, and then the
+// PAGEFEEDDOTS will be added to the final paper length. If you need a specific paperlength, then make sure
+// that marginLengthDots is >= MIN_PAGEFEEDDOTS.
+
+#define TD2125NWB_MIN_MARGINLENGTHDOTS 0
+// v2.3.0 UPDATE: Instead of forcing this MIN_PAGEFEEDDOTS value on EVERY page, which essentially PREVENTS a "no gap"
+// solution if the FW actually supports it, now we only force it on the LAST page, allowing a 0-margin between pages
+// in case the FW allows it. But, we will force this on the LAST page, to assure the FW will eject the page to tear off
+// in case it doesn't automatically behave that way.
+#define TD2125NWB_MIN_PAGEFEEDDOTS_LASTPAGE 24
+
+#endif
+
+#define TD2125NWB_MAX_MARGINLENGTHDOTS 1015
+// Arbitrarily restrict extraFeed to 11" at 203 dpi. There is no reason to be larger.
+#define TD2125NWB_MAX_EXTRAFEEDDOTS (11*TD2125NWB_RESOLUTION_VERT)
+
+//*** IMPORTANT ***
+// SDK Users:
+// You should NEVER instantiate an object of the GenericMobileLabelModelPrintSettings superclass.
+// Instead, you should instantiate one of the model-specific subclasses (i.e. TD2125NWBPrintSettings).
+//
+// For a list of important properties in the settings that your application needs to set,
+// refer to the GenericMobileLabelModelPrintSettings superclass.
+
+// SDK Designers:
+// The GenericMobileLabelModelPrintSettings superclass handles all the important work.
+// This subclass only needs to provide the model-specific data to the generic class(es).
+
+//*** ADDITIONAL PROPERTIES not handled by GenericMobileLabelModelPrintSettings
+@property (nonatomic, assign) BOOL peelerEnabled;
+@property (nonatomic, assign) BOOL invert180degrees;
+
+
+@end

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2125NWBPrintSettingsViewController.h

@@ -0,0 +1,42 @@
+//
+//  TD2125NWBPrintSettingsViewController.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2125NWBPrintSettings.h>
+
+// This is the DEFAULT popup contentSize for TD2125NWBPrintSettingsViewController.
+//
+// You can override this by setting the "popoverSize" property (defined in the
+// PrintSettingsViewController superclass) to something different
+// before showing the ViewController.
+//
+// The popoverSize setting will be propagated to all of the "child" ViewControllers
+// of the main ViewController so all of the detail views will be the SAME size as each other.
+//
+// NOTE: iPad1 and iPad2 size = 1024 x 768, iPad3 = 2048 x 1536
+//#define TD2125NWBPOPUPCONTENTSIZE CGSizeMake(400,480)
+#define TD2125NWBPOPUPCONTENTSIZE CGSizeMake(400,548)
+#define TD2125NWBPOPUPCONTENTSIZE_IOS7 CGSizeMake(400,588)
+
+
+/*
+ This class is a subclass of GenericMobileLabelModelPrintSettingsViewController,
+ which implements all the major functionality.
+ 
+ *** SDK Users:  
+ DO NOT INSTANTIATE an instance of GenericMobileLabelModelPrintSettingsViewController.
+ Always instantiate a model-specific class, e.g. TD2125NWBPrintSettingsViewController
+ */
+
+@interface TD2125NWBPrintSettingsViewController : GenericMobileLabelModelPrintSettingsViewController
+{
+}
+
+@end
+
+

package/ios/Pods/{BRLMPrinterKit/BRLMPrinterKit → BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64}/BRLMPrinterKit.framework/Headers/TD2130NPrintSettings.h

@@ -6,7 +6,7 @@
 //  Copyright (c) 2013 Brother Mobile Solutions. All rights reserved.
 //
 
-#import "GenericMobileLabelModelPrintSettings.h"
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
 
 
 @interface TD2130NPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>

package/ios/Pods/{BRLMPrinterKit/BRLMPrinterKit → BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64}/BRLMPrinterKit.framework/Headers/TD2130NPrintSettingsViewController.h

@@ -6,8 +6,8 @@
 //  Copyright (c) 2013 Brother Mobile Solutions. All rights reserved.
 //
 
-#import "GenericMobileLabelModelPrintSettingsViewController.h"
-#import "TD2130NPrintSettings.h"
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2130NPrintSettings.h>
 
 // This is the DEFAULT popup contentSize for TD2130NPrintSettingsViewController.
 //

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2135NPrintSettings.h

@@ -0,0 +1,82 @@
+//
+//  TD2135NPrintSettings.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
+
+
+@interface TD2135NPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>
+
+// These definitions are provided for information only. DO NOT MODIFY!
+// spec section 2.3.1 Resolution
+#define TD2135N_RESOLUTION_HORZ 300
+#define TD2135N_RESOLUTION_VERT 300
+// spec section 2.3.5 Raster Line
+#define TD2135N_HEADSIZEDOTS 672
+// spec section "Select compression mode" command
+// NOTE: This should be same as HEADSIZEDOTS/8. And, it should be same as the # of decompressed bytes.
+#define TD2135N_MAX_COMPRESS_LENGTH 84
+
+// not in spec. Used Windows Printer Driver as reference.
+// NOTE: MAXPAPERWIDTH can exceed HEADSIZEDOTS!!
+#define TD2135N_MIN_PAPERWIDTHDOTS (0.47F * TD2135N_RESOLUTION_HORZ) // 141
+#define TD2135N_MAX_PAPERWIDTHDOTS (2.48F * TD2135N_RESOLUTION_VERT) // 744
+// spec section 2.3.4 Maximum and Minimum Lengths
+#define TD2135N_MIN_PAPERLENGTHDOTS 142
+#define TD2135N_MAX_PAPERLENGTHDOTS 11811
+// spec section 2.3.3 Feed Amount
+#ifdef OLD
+// IMPORTANT NOTE: For LABEL papertype ONLY, we allow the MIN marginlengthdots to be set to 0.
+// That is, this MIN value here is ignored when papertype = label is specified.
+// Consider the case of a 1.0x0.5" label. A min margin of 0.12" will take up half of the printable length!!
+// This is why we will allow the margin to be set to 0 in this case.
+// Beware that some labels might clip the top if this is set to 0. But, other settings can be tweaked to
+// make it work (such as by setting a larger paperlength and setting the top margin to non-zero.)
+#define TD2135N_MIN_MARGINLENGTHDOTS 35
+
+#else
+// Allow 0 now for continuous roll too, as the Esc iUw command generated from this can affect AirPrint.
+// However, if this is 0, then the Esc id command will send 0 too. And, the printer may not eject the page
+// enough at the end. So, I am introducing the MIN_PAGEFEEDDOTS definition now, so that if current marginLengthDots
+// is LESS than MIN_PAGEFEEDDOTS, we will send Esc id command using the MIN_PAGEFEEDDOTS value instead.
+// Otherwise, the Esc id command will use the marginLengthDots value as it has in the past.
+//
+// NOTE: If this occurs, the final paper length after tear off will be up to 1/4" longer than the
+// specified paperLengthDots, because the print data will be (up to) the entire paper length, and then the
+// PAGEFEEDDOTS will be added to the final paper length. If you need a specific paperlength, then make sure
+// that marginLengthDots is >= MIN_PAGEFEEDDOTS.
+
+#define TD2135N_MIN_MARGINLENGTHDOTS 0
+// v2.3.0 UPDATE: Instead of forcing this MIN_PAGEFEEDDOTS value on EVERY page, which essentially PREVENTS a "no gap"
+// solution if the FW actually supports it, now we only force it on the LAST page, allowing a 0-margin between pages
+// in case the FW allows it. But, we will force this on the LAST page, to assure the FW will eject the page to tear off
+// in case it doesn't automatically behave that way.
+#define TD2135N_MIN_PAGEFEEDDOTS_LASTPAGE 35
+
+#endif
+
+#define TD2135N_MAX_MARGINLENGTHDOTS 1500
+// Arbitrarily restrict extraFeed to 11" at 203 dpi. There is no reason to be larger.
+#define TD2135N_MAX_EXTRAFEEDDOTS (11*TD2135N_RESOLUTION_VERT)
+
+//*** IMPORTANT ***
+// SDK Users:
+// You should NEVER instantiate an object of the GenericMobileLabelModelPrintSettings superclass.
+// Instead, you should instantiate one of the model-specific subclasses (i.e. TD2135NPrintSettings).
+//
+// For a list of important properties in the settings that your application needs to set,
+// refer to the GenericMobileLabelModelPrintSettings superclass.
+
+// SDK Designers:
+// The GenericMobileLabelModelPrintSettings superclass handles all the important work.
+// This subclass only needs to provide the model-specific data to the generic class(es).
+
+//*** ADDITIONAL PROPERTIES not handled by GenericMobileLabelModelPrintSettings
+@property (nonatomic, assign) BOOL peelerEnabled;
+@property (nonatomic, assign) BOOL invert180degrees;
+
+@end

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2135NPrintSettingsViewController.h

@@ -0,0 +1,42 @@
+//
+//  TD2135NPrintSettingsViewController.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2135NPrintSettings.h>
+
+// This is the DEFAULT popup contentSize for TD2135NPrintSettingsViewController.
+//
+// You can override this by setting the "popoverSize" property (defined in the
+// PrintSettingsViewController superclass) to something different
+// before showing the ViewController.
+//
+// The popoverSize setting will be propagated to all of the "child" ViewControllers
+// of the main ViewController so all of the detail views will be the SAME size as each other.
+//
+// NOTE: iPad1 and iPad2 size = 1024 x 768, iPad3 = 2048 x 1536
+//#define TD2135NPOPUPCONTENTSIZE CGSizeMake(400,480)
+#define TD2135NPOPUPCONTENTSIZE CGSizeMake(400,548)
+#define TD2135NPOPUPCONTENTSIZE_IOS7 CGSizeMake(400,588)
+
+
+/*
+ This class is a subclass of GenericMobileLabelModelPrintSettingsViewController,
+ which implements all the major functionality.
+ 
+  *** SDK Users:  
+ DO NOT INSTANTIATE an instance of GenericMobileLabelModelPrintSettingsViewController.
+ Always instantiate a model-specific class, e.g. TD2135NPrintSettingsViewController
+ */
+
+@interface TD2135NPrintSettingsViewController : GenericMobileLabelModelPrintSettingsViewController
+{
+}
+
+@end
+
+

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2135NWBPrintSettings.h

@@ -0,0 +1,82 @@
+//
+//  TD2135NWBPrintSettings.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
+
+
+@interface TD2135NWBPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>
+
+// These definitions are provided for information only. DO NOT MODIFY!
+// spec section 2.3.1 Resolution
+#define TD2135NWB_RESOLUTION_HORZ 300
+#define TD2135NWB_RESOLUTION_VERT 300
+// spec section 2.3.5 Raster Line
+#define TD2135NWB_HEADSIZEDOTS 672
+// spec section "Select compression mode" command
+// NOTE: This should be same as HEADSIZEDOTS/8. And, it should be same as the # of decompressed bytes.
+#define TD2135NWB_MAX_COMPRESS_LENGTH 84
+
+// not in spec. Used Windows Printer Driver as reference.
+// NOTE: MAXPAPERWIDTH can exceed HEADSIZEDOTS!!
+#define TD2135NWB_MIN_PAPERWIDTHDOTS (0.47F * TD2135NWB_RESOLUTION_HORZ) // 141
+#define TD2135NWB_MAX_PAPERWIDTHDOTS (2.48F * TD2135NWB_RESOLUTION_VERT) // 744
+// spec section 2.3.4 Maximum and Minimum Lengths
+#define TD2135NWB_MIN_PAPERLENGTHDOTS 142
+#define TD2135NWB_MAX_PAPERLENGTHDOTS 11811
+// spec section 2.3.3 Feed Amount
+#ifdef OLD
+// IMPORTANT NOTE: For LABEL papertype ONLY, we allow the MIN marginlengthdots to be set to 0.
+// That is, this MIN value here is ignored when papertype = label is specified.
+// Consider the case of a 1.0x0.5" label. A min margin of 0.12" will take up half of the printable length!!
+// This is why we will allow the margin to be set to 0 in this case.
+// Beware that some labels might clip the top if this is set to 0. But, other settings can be tweaked to
+// make it work (such as by setting a larger paperlength and setting the top margin to non-zero.)
+#define TD2135NWB_MIN_MARGINLENGTHDOTS 35
+
+#else
+// Allow 0 now for continuous roll too, as the Esc iUw command generated from this can affect AirPrint.
+// However, if this is 0, then the Esc id command will send 0 too. And, the printer may not eject the page
+// enough at the end. So, I am introducing the MIN_PAGEFEEDDOTS definition now, so that if current marginLengthDots
+// is LESS than MIN_PAGEFEEDDOTS, we will send Esc id command using the MIN_PAGEFEEDDOTS value instead.
+// Otherwise, the Esc id command will use the marginLengthDots value as it has in the past.
+//
+// NOTE: If this occurs, the final paper length after tear off will be up to 1/4" longer than the
+// specified paperLengthDots, because the print data will be (up to) the entire paper length, and then the
+// PAGEFEEDDOTS will be added to the final paper length. If you need a specific paperlength, then make sure
+// that marginLengthDots is >= MIN_PAGEFEEDDOTS.
+
+#define TD2135NWB_MIN_MARGINLENGTHDOTS 0
+// v2.3.0 UPDATE: Instead of forcing this MIN_PAGEFEEDDOTS value on EVERY page, which essentially PREVENTS a "no gap"
+// solution if the FW actually supports it, now we only force it on the LAST page, allowing a 0-margin between pages
+// in case the FW allows it. But, we will force this on the LAST page, to assure the FW will eject the page to tear off
+// in case it doesn't automatically behave that way.
+#define TD2135NWB_MIN_PAGEFEEDDOTS_LASTPAGE 35
+
+#endif
+
+#define TD2135NWB_MAX_MARGINLENGTHDOTS 1500
+// Arbitrarily restrict extraFeed to 11" at 203 dpi. There is no reason to be larger.
+#define TD2135NWB_MAX_EXTRAFEEDDOTS (11*TD2135NWB_RESOLUTION_VERT)
+
+//*** IMPORTANT ***
+// SDK Users:
+// You should NEVER instantiate an object of the GenericMobileLabelModelPrintSettings superclass.
+// Instead, you should instantiate one of the model-specific subclasses (i.e. TD2135NWBPrintSettings).
+//
+// For a list of important properties in the settings that your application needs to set,
+// refer to the GenericMobileLabelModelPrintSettings superclass.
+
+// SDK Designers:
+// The GenericMobileLabelModelPrintSettings superclass handles all the important work.
+// This subclass only needs to provide the model-specific data to the generic class(es).
+
+//*** ADDITIONAL PROPERTIES not handled by GenericMobileLabelModelPrintSettings
+@property (nonatomic, assign) BOOL peelerEnabled;
+@property (nonatomic, assign) BOOL invert180degrees;
+
+@end

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2135NWBPrintSettingsViewController.h

@@ -0,0 +1,42 @@
+//
+//  TD2135NWBPrintSettingsViewController.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 5/5/23.
+//  Copyright (c) 2023 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2135NWBPrintSettings.h>
+
+// This is the DEFAULT popup contentSize for TD2135NWBPrintSettingsViewController.
+//
+// You can override this by setting the "popoverSize" property (defined in the
+// PrintSettingsViewController superclass) to something different
+// before showing the ViewController.
+//
+// The popoverSize setting will be propagated to all of the "child" ViewControllers
+// of the main ViewController so all of the detail views will be the SAME size as each other.
+//
+// NOTE: iPad1 and iPad2 size = 1024 x 768, iPad3 = 2048 x 1536
+//#define TD2135NWBPOPUPCONTENTSIZE CGSizeMake(400,480)
+#define TD2135NWBPOPUPCONTENTSIZE CGSizeMake(400,548)
+#define TD2135NWBPOPUPCONTENTSIZE_IOS7 CGSizeMake(400,588)
+
+
+/*
+ This class is a subclass of GenericMobileLabelModelPrintSettingsViewController,
+ which implements all the major functionality.
+ 
+  *** SDK Users:  
+ DO NOT INSTANTIATE an instance of GenericMobileLabelModelPrintSettingsViewController.
+ Always instantiate a model-specific class, e.g. TD2135NWBPrintSettingsViewController
+ */
+
+@interface TD2135NWBPrintSettingsViewController : GenericMobileLabelModelPrintSettingsViewController
+{
+}
+
+@end
+
+

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2320DFPrintSettings.h

@@ -0,0 +1,47 @@
+//
+//  TD2320DFPrintSettings.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 2/16/24.
+//  Copyright (c) 2024 Brother Mobile Solutions. All rights reserved.
+//
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettings.h>
+
+
+@interface TD2320DFPrintSettings : GenericMobileLabelModelPrintSettings <PrintSettingsDelegate>
+
+
+//*** IMPORTANT ***
+// SDK Users:
+// You should NEVER instantiate an object of the GenericMobileLabelModelPrintSettings superclass.
+// Instead, you should instantiate one of the model-specific subclasses (i.e. TD2320DFPrintSettings).
+//
+// For a list of important properties in the settings that your application needs to set,
+// refer to the GenericMobileLabelModelPrintSettings superclass.
+
+// SDK Designers:
+// The GenericMobileLabelModelPrintSettings superclass handles all the important work.
+// This subclass only needs to provide the model-specific data to the generic class(es).
+
+//*** ADDITIONAL PROPERTIES not handled by GenericMobileLabelModelPrintSettings
+// NOTE: TD23xx models can be either 203 or 300 dpi depending on print head installed.
+@property (nonatomic, assign) RESOLUTION printerResolution;
+
+// NOTE: Linerless models do NOT support peeler
+@property (nonatomic, assign) BOOL invert180degrees;
+
+// The following are used with the cutter
+@property (nonatomic, assign) BOOL cutAtEndOfJobEnabled; // true: cuts at end of last page of job
+@property (nonatomic, assign) BOOL autoCutEnabled; // true: automatically cuts every N labels, as specified by autoCutEveryNLabels
+@property (nonatomic, assign) unsigned int autoCutEveryNLabels; // default is 1 -> autocut each label. Set value to print N labels before cutting. Allowed Range is 1 to TD2320DF_MAX_AUTOCUT_NUMLABELS.
+
+// NOTE: This particular #define is needed in DataController.
+// All other #defines were moved into the .m file.
+
+// spec section "Select compression mode" command
+// NOTE: This should be same as HEADSIZEDOTS/8. And, it should be same as the # of decompressed bytes.
+#define TD2320DF_MAX_COMPRESS_LENGTH_203 59 // 59 = 472/8
+#define TD2320DF_MAX_COMPRESS_LENGTH_300 87 // 87 = 696/8
+
+@end

package/ios/Pods/BRLMPrinterKit_v4/BRLMPrinterKit/BRLMPrinterKit.xcframework/ios-arm64/BRLMPrinterKit.framework/Headers/TD2320DFPrintSettingsViewController.h

@@ -0,0 +1,43 @@
+//
+//  TD2320DFPrintSettingsViewController.h
+//  BMSPrinterKit
+//
+//  Created by BMS on 2/16/24.
+//  Copyright (c) 2024 Brother Mobile Solutions. All rights reserved.
+//
+
+
+#import <BRLMPrinterKit/GenericMobileLabelModelPrintSettingsViewController.h>
+#import <BRLMPrinterKit/TD2320DFPrintSettings.h>
+
+// This is the DEFAULT popup contentSize for TD2320DFPrintSettingsViewController.
+//
+// You can override this by setting the "popoverSize" property (defined in the
+// PrintSettingsViewController superclass) to something different
+// before showing the ViewController.
+//
+// The popoverSize setting will be propagated to all of the "child" ViewControllers
+// of the main ViewController so all of the detail views will be the SAME size as each other.
+//
+// NOTE: iPad1 and iPad2 size = 1024 x 768, iPad3 = 2048 x 1536
+//#define TD2320DFPOPUPCONTENTSIZE CGSizeMake(400,480)
+#define TD2320DFPOPUPCONTENTSIZE CGSizeMake(400,548)
+#define TD2320DFPOPUPCONTENTSIZE_IOS7 CGSizeMake(400,588)
+
+
+/*
+ This class is a subclass of GenericMobileLabelModelPrintSettingsViewController,
+ which implements all the major functionality.
+ 
+ *** SDK Users:  
+ DO NOT INSTANTIATE an instance of GenericMobileLabelModelPrintSettingsViewController.
+ Always instantiate a model-specific class, e.g. TD2320DFPrintSettingsViewController
+ */
+
+@interface TD2320DFPrintSettingsViewController : GenericMobileLabelModelPrintSettingsViewController
+{
+}
+
+@end
+
+