@project-chip/matter.js 0.4.0 → 0.5.0

package/dist/cjs/cluster/definitions/PumpConfigurationAndControlCluster.d.ts

@@ -0,0 +1,2200 @@
+/**
+ * @license
+ * Copyright 2022-2023 Project CHIP Authors
+ * SPDX-License-Identifier: Apache-2.0
+ */
+import { BaseClusterComponent, ClusterComponent, ExtensibleCluster, ClusterForBaseCluster, AsConditional } from "../../cluster/ClusterFactory.js";
+import { BitFlag, BitFlags, TypeFromPartialBitSchema } from "../../schema/BitmapSchema.js";
+import { FixedAttribute, OptionalAttribute, Attribute, OptionalWritableAttribute, WritableAttribute, OptionalEvent, OptionalFixedAttribute, Cluster as CreateCluster } from "../../cluster/Cluster.js";
+export declare namespace PumpConfigurationAndControl {
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1
+     */
+    const PumpStatusBitmap: {
+        /**
+         * A fault related to the system or pump device is detected.
+         *
+         * If this bit is set, it may correspond to an event in the range 2-16, see Events.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.1
+         */
+        deviceFault: BitFlag;
+        /**
+         * A fault related to the supply to the pump is detected.
+         *
+         * If this bit is set, it may correspond to an event in the range 0-1 or 13, see Events.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.2
+         */
+        supplyFault: BitFlag;
+        /**
+         * Setpoint is too low to achieve.
+         */
+        speedLow: BitFlag;
+        /**
+         * Setpoint is too high to achieve.
+         */
+        speedHigh: BitFlag;
+        /**
+         * Device control is overridden by hardware, such as an external STOP button or via a local HMI.
+         *
+         * While this bit is set, the EffectiveOperationMode is adjusted to Local. Any request changing OperationMode
+         * shall generate a FAILURE error status until LocalOverride is cleared on the physical device. When
+         * LocalOverride is cleared, the device shall return to the operation mode set in OperationMode.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.3
+         */
+        localOverride: BitFlag;
+        /**
+         * Pump is currently running
+         */
+        running: BitFlag;
+        /**
+         * A remote pressure sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantPressure and the setpoint for the pump is interpreted as
+         * a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.4
+         */
+        remotePressure: BitFlag;
+        /**
+         * A remote flow sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantFlow, and the setpoint for the pump is interpreted as a
+         * percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.5
+         */
+        remoteFlow: BitFlag;
+        /**
+         * A remote temperature sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantTemperature, and the setpoint for the pump is
+         * interpreted as a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue])
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.6
+         */
+        remoteTemperature: BitFlag;
+    };
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.2
+     */
+    const enum OperationMode {
+        /**
+         * The pump is controlled by a setpoint, as defined by a connected remote sensor or by the ControlMode
+         * attribute.
+         *
+         * If the pump is running in this operation mode the setpoint is an internal variable which may be controlled
+         * between 0% and 100%, e.g., by means of the Level Control cluster
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.2.1
+         */
+        Normal = 0,
+        /**
+         * This value sets the pump to run at the minimum possible speed it can without being stopped.
+         */
+        Minimum = 1,
+        /**
+         * This value sets the pump to run at its maximum possible speed.
+         */
+        Maximum = 2,
+        /**
+         * This value sets the pump to run with the local settings of the pump, regardless of what these are.
+         */
+        Local = 3
+    }
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3
+     */
+    const enum ControlMode {
+        /**
+         * The pump is running at a constant speed.
+         *
+         * The setpoint is interpreted as a percentage of the range derived from the [MinConstSpeed – MaxConstSpeed]
+         * attributes.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.1
+         */
+        ConstantSpeed = 0,
+        /**
+         * The pump will regulate its speed to maintain a constant differential pressure over its flanges.
+         *
+         * The setpoint is interpreted as a percentage of the range of the sensor used for this control mode. In case
+         * of the internal pressure sensor, this will be the range derived from the [MinConstPressure –
+         * MaxConstPressure] attributes. In case of a remote pressure sensor, this will be the range derived from the
+         * [MinMeasuredValue – MaxMeasuredValue] attributes of the remote pressure sensor.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.2
+         */
+        ConstantPressure = 1,
+        /**
+         * The pump will regulate its speed to maintain a constant differential pressure over its flanges.
+         *
+         * The setpoint is interpreted as a percentage of the range derived of the [MinCompPressure – MaxCompPressure]
+         * attributes. The internal setpoint will be lowered (compensated) dependent on the flow in the pump (lower
+         * flow ⇒ lower internal setpoint).
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.3
+         */
+        ProportionalPressure = 2,
+        /**
+         * The pump will regulate its speed to maintain a constant flow through the pump.
+         *
+         * The setpoint is interpreted as a percentage of the range of the sensor used for this control mode. In case
+         * of the internal flow sensor, this will be the range derived from the [MinConstFlow – MaxConstFlow]
+         * attributes. In case of a remote flow sensor, this will be the range derived from the [MinMeasuredValue –
+         * MaxMeasuredValue] attributes of the remote flow sensor.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.4
+         */
+        ConstantFlow = 3,
+        /**
+         * The pump will regulate its speed to maintain a constant temperature.
+         *
+         * The setpoint is interpreted as a percentage of the range of the sensor used for this control mode. In case
+         * of the internal temperature sensor, this will be the range derived from the [MinConstTemp – MaxConstTemp]
+         * attributes. In case of a remote temperature sensor, this will be the range derived from the
+         * [MinMeasuredValue – MaxMeasuredValue] attributes of the remote temperature sensor.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.5
+         */
+        ConstantTemperature = 5,
+        /**
+         * The operation of the pump is automatically optimized to provide the most suitable performance with respect
+         * to comfort and energy savings.
+         *
+         * This behavior is manufacturer defined. The pump can be stopped by setting the setpoint of the level control
+         * cluster to 0, or by using the On/Off cluster. If the pump is started (at any setpoint), the speed of the
+         * pump is entirely determined by the pump.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.3.6
+         */
+        Automatic = 7
+    }
+    /**
+     * These are optional features supported by PumpConfigurationAndControlCluster.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.4
+     */
+    enum Feature {
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        ConstantPressure = "ConstantPressure",
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        CompensatedPressure = "CompensatedPressure",
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        ConstantFlow = "ConstantFlow",
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        ConstantSpeed = "ConstantSpeed",
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        ConstantTemperature = "ConstantTemperature",
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        Automatic = "Automatic",
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        LocalOperation = "LocalOperation"
+    }
+    /**
+     * These elements and properties are present in all PumpConfigurationAndControl clusters.
+     */
+    const Base: BaseClusterComponent<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }, {
+        /**
+         * This attribute specifies the maximum pressure the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is -3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.1
+         */
+        maxPressure: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum speed the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.2
+         */
+        maxSpeed: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum flow the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.3
+         */
+        maxFlow: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the activity status of the pump functions as listed in PumpStatusBitmap. Where
+         * a pump controller function is active, the corresponding bit shall be set to 1. Where a pump controller
+         * function is not active, the corresponding bit shall be set to 0.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.14
+         */
+        pumpStatus: OptionalAttribute<TypeFromPartialBitSchema<{
+            /**
+             * A fault related to the system or pump device is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 2-16, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.1
+             */
+            deviceFault: BitFlag;
+            /**
+             * A fault related to the supply to the pump is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 0-1 or 13, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.2
+             */
+            supplyFault: BitFlag;
+            /**
+             * Setpoint is too low to achieve.
+             */
+            speedLow: BitFlag;
+            /**
+             * Setpoint is too high to achieve.
+             */
+            speedHigh: BitFlag;
+            /**
+             * Device control is overridden by hardware, such as an external STOP button or via a local HMI.
+             *
+             * While this bit is set, the EffectiveOperationMode is adjusted to Local. Any request changing OperationMode
+             * shall generate a FAILURE error status until LocalOverride is cleared on the physical device. When
+             * LocalOverride is cleared, the device shall return to the operation mode set in OperationMode.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.3
+             */
+            localOverride: BitFlag;
+            /**
+             * Pump is currently running
+             */
+            running: BitFlag;
+            /**
+             * A remote pressure sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantPressure and the setpoint for the pump is interpreted as
+             * a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.4
+             */
+            remotePressure: BitFlag;
+            /**
+             * A remote flow sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantFlow, and the setpoint for the pump is interpreted as a
+             * percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.5
+             */
+            remoteFlow: BitFlag;
+            /**
+             * A remote temperature sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantTemperature, and the setpoint for the pump is
+             * interpreted as a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue])
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.6
+             */
+            remoteTemperature: BitFlag;
+        }>, any>;
+        /**
+         * This attribute specifies current effective operation mode of the pump as defined in OperationModeEnum.
+         *
+         * The value of the EffectiveOperationMode attribute is the same as the OperationMode attribute, unless one
+         * of the following points are true:
+         *
+         *   • The pump is physically set to run with the local settings
+         *
+         *   • The LocalOverride bit in the PumpStatus attribute is set,
+         *
+         * See OperationMode and ControlMode attributes for a detailed description of the operation and control of
+         * the pump.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.15
+         */
+        effectiveOperationMode: Attribute<OperationMode, any>;
+        /**
+         * This attribute specifies the current effective control mode of the pump as defined in ControlModeEnum.
+         *
+         * This attribute contains the control mode that currently applies to the pump. It will have the value of
+         * the ControlMode attribute, unless one of the following points are true:
+         *
+         *   • The ControlMode attribute is set to Automatic. In this case, the value of the EffectiveControlMode
+         *     shall match the behavior of the pump.
+         *
+         *   • A remote sensor is used as the sensor for regulation of the pump. In this case, EffectiveControlMode
+         *     will display ConstantPressure, ConstantFlow or ConstantTemperature if the remote sensor is a
+         *     pressure sensor, a flow sensor or a temperature sensor respectively, regardless of the value of the
+         *     ControlMode attribute.
+         *
+         * In case the ControlMode attribute is not included on the device and no remote sensors are connected, the
+         * value of the EffectiveControlMode shall match the vendor-specific behavior of the pump.
+         *
+         * See OperationMode and ControlMode attributes for detailed a description of the operation and control of
+         * the pump.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.16
+         */
+        effectiveControlMode: Attribute<ControlMode, any>;
+        /**
+         * This attribute specifies the actual capacity of the pump as a percentage of the effective maximum
+         * setpoint value. It is updated dynamically as the speed of the pump changes.
+         *
+         * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+         * attribute will indicate the null value.
+         *
+         * Valid range is 0 % to 163.835% (0.005 % granularity). Although this attribute is a signed value, values
+         * of capacity less than zero have no physical meaning.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.17
+         */
+        capacity: Attribute<number | null, any>;
+        /**
+         * This attribute specifies the actual speed of the pump measured in RPM. It is updated dynamically as the
+         * speed of the pump changes.
+         *
+         * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+         * attribute will indicate the null value.
+         *
+         * Valid range is 0 to 65.534 RPM.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.18
+         */
+        speed: OptionalAttribute<number | null, any>;
+        /**
+         * This attribute specifies the accumulated number of hours that the pump has been powered and the motor
+         * has been running. It is updated dynamically as it increases. It is preserved over power cycles of the
+         * pump. If LifeTimeRunningHours rises above maximum value it “rolls over” and starts at 0 (zero).
+         *
+         * This attribute is writeable, in order to allow setting to an appropriate value after maintenance. If
+         *
+         * the value is not available, this attribute will indicate the null value. Valid range is 0 to 16,777,214
+         * hrs.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.19
+         */
+        lifetimeRunningHours: OptionalWritableAttribute<number | null, any>;
+        /**
+         * This attribute specifies the actual power consumption of the pump in Watts. The value of this attribute
+         * is updated dynamically as the power consumption of the pump changes.
+         *
+         * This attribute is read only. If the value is not available (the measurement of power consumption is not
+         * done in the pump), this attribute will indicate the null value.
+         *
+         * Valid range is 0 to 16,777,214 Watts.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.20
+         */
+        power: OptionalAttribute<number | null, any>;
+        /**
+         * This attribute specifies the accumulated energy consumption of the pump through the entire lifetime of
+         * the pump in kWh. The value of the LifetimeEnergyConsumed attribute is updated dynamically as the energy
+         * consumption of the pump increases. If LifetimeEnergyConsumed rises above maximum value it “rolls over”
+         * and starts at 0 (zero).
+         *
+         * This attribute is writeable, in order to allow setting to an appropriate value after maintenance.
+         *
+         * Valid range is 0 kWh to 4,294,967,294 kWh.
+         *
+         * This attribute shall be null if the value is unknown.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.21
+         */
+        lifetimeEnergyConsumed: OptionalWritableAttribute<number | null, any>;
+        /**
+         * This attribute specifies the operation mode of the pump as defined in OperationModeEnum.
+         *
+         * The actual operating mode of the pump is a result of the setting of the attributes OperationMode,
+         * ControlMode and the optional connection of a remote sensor. The operation and control is prioritized as
+         * shown in the scheme below:
+         *
+         * Priority Scheme of Pump Operation and Control
+         *
+         * If this attribute is Maximum, Minimum or Local, the OperationMode attribute decides how the pump is
+         * operated.
+         *
+         * If this attribute is Normal and a remote sensor is connected to the pump, the type of the remote sensor
+         * decides the control mode of the pump. A connected remote pressure sensor will make the pump run in
+         * control mode Constant pressure and vice versa for flow and temperature type sensors. This is regardless
+         * of the setting of the ControlMode attribute.
+         *
+         * If this attribute is Normal and no remote sensor is connected, the control mode of the pump is decided
+         * by the ControlMode attribute.
+         *
+         * OperationMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+         * point of changing the value of this attribute is vendor-specific.
+         *
+         * In the case a device does not support a specific operation mode, the write interaction to this attribute
+         * with an unsupported operation mode value shall be ignored and a response containing the status of
+         * CONSTRAINT_ERROR shall be returned.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.22
+         */
+        operationMode: WritableAttribute<OperationMode, any>;
+        /**
+         * This attribute specifies the control mode of the pump as defined in ControlModeEnum.
+         *
+         * See the OperationMode attribute for a detailed description of the operation and control of the
+         *
+         * pump.
+         *
+         * ControlMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+         * point of changing is vendor-specific.
+         *
+         * In the case a device does not support a specific control mode, the write interaction to this attribute
+         * with an unsupported control mode value shall be ignored and a response containing the status of
+         * CONSTRAINT_ERROR shall be returned.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.23
+         */
+        controlMode: OptionalWritableAttribute<ControlMode, any>;
+    }, import("../../cluster/Cluster.js").Commands, {
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        powerMissingPhase: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        dryRunning: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        motorTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpMotorFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpBlocked: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        sensorFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicNonFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        generalFault: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        leakage: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        airDetection: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        turbineOperation: OptionalEvent<void, any>;
+    }>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature ConstantPressure.
+     */
+    const ConstantPressureComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum pressure the pump can achieve when it is working with the
+         * ControlMode attribute set to ConstantPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.4
+         */
+        minConstPressure: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum pressure the pump can achieve when it is working with the
+         * ControlMode attribute set to ConstantPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.5
+         */
+        maxConstPressure: FixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature Automatic.
+     */
+    const AutomaticComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum pressure the pump can achieve when it is working with the
+         * ControlMode attribute set to ConstantPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.4
+         */
+        minConstPressure: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum pressure the pump can achieve when it is working with the
+         * ControlMode attribute set to ConstantPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.5
+         */
+        maxConstPressure: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the minimum compensated pressure the pump can achieve when it is working with
+         * the ControlMode attribute set to ProportionalPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.6
+         */
+        minCompPressure: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum compensated pressure the pump can achieve when it is working with
+         * the ControlMode attribute set to ProportionalPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.7
+         */
+        maxCompPressure: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the minimum speed the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantSpeed.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.8
+         */
+        minConstSpeed: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum speed the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantSpeed.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.9
+         */
+        maxConstSpeed: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the minimum flow the pump can achieve when it is working with the Con
+         *
+         * trolMode attribute set to ConstantFlow.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.10
+         */
+        minConstFlow: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum flow the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantFlow.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.11
+         */
+        maxConstFlow: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the minimum temperature the pump can maintain in the system when it is working
+         * with the ControlMode attribute set to ConstantTemperature.
+         *
+         * Valid range is –273.15 °C to 327.67 °C (steps of 0.01 °C). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.12
+         */
+        minConstTemp: OptionalFixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum temperature the pump can maintain in the system when it is working
+         * with the ControlMode attribute set to ConstantTemperature.
+         *
+         * MaxConstTemp shall be greater than or equal to MinConstTemp
+         *
+         * Valid range is –273.15 °C to 327.67 °C (steps of 0.01 °C). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.13
+         */
+        maxConstTemp: OptionalFixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature CompensatedPressure.
+     */
+    const CompensatedPressureComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum compensated pressure the pump can achieve when it is working with
+         * the ControlMode attribute set to ProportionalPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.6
+         */
+        minCompPressure: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum compensated pressure the pump can achieve when it is working with
+         * the ControlMode attribute set to ProportionalPressure.
+         *
+         * Valid range is –3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.7
+         */
+        maxCompPressure: FixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature ConstantSpeed.
+     */
+    const ConstantSpeedComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum speed the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantSpeed.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.8
+         */
+        minConstSpeed: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum speed the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantSpeed.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.9
+         */
+        maxConstSpeed: FixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature ConstantFlow.
+     */
+    const ConstantFlowComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum flow the pump can achieve when it is working with the Con
+         *
+         * trolMode attribute set to ConstantFlow.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.10
+         */
+        minConstFlow: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum flow the pump can achieve when it is working with the ControlMode
+         * attribute set to ConstantFlow.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.11
+         */
+        maxConstFlow: FixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * A PumpConfigurationAndControlCluster supports these elements if it supports feature ConstantTemperature.
+     */
+    const ConstantTemperatureComponent: ClusterComponent<{
+        /**
+         * This attribute specifies the minimum temperature the pump can maintain in the system when it is working
+         * with the ControlMode attribute set to ConstantTemperature.
+         *
+         * Valid range is –273.15 °C to 327.67 °C (steps of 0.01 °C). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.12
+         */
+        minConstTemp: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum temperature the pump can maintain in the system when it is working
+         * with the ControlMode attribute set to ConstantTemperature.
+         *
+         * MaxConstTemp shall be greater than or equal to MinConstTemp
+         *
+         * Valid range is –273.15 °C to 327.67 °C (steps of 0.01 °C). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.13
+         */
+        maxConstTemp: FixedAttribute<number | null, any>;
+    }, import("../../cluster/Cluster.js").Commands, import("../../cluster/Cluster.js").Events>;
+    /**
+     * Pump Configuration and Control
+     *
+     * The Pump Configuration and Control cluster provides an interface for the setup and control of pump devices, and
+     * the automatic reporting of pump status information. Note that control of pump speed is not included – speed is
+     * controlled by the On/Off and Level Control clusters.
+     *
+     * PumpConfigurationAndControlCluster supports optional features that you can enable with the
+     * PumpConfigurationAndControlCluster.with() factory method.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2
+     */
+    const Cluster: ExtensibleCluster<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }, TypeFromPartialBitSchema<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }>, import("../../util/Type.js").Merge<{
+        /**
+         * This attribute specifies the maximum pressure the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is -3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+         * is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.1
+         */
+        maxPressure: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum speed the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.2
+         */
+        maxSpeed: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the maximum flow the pump can achieve. It is a physical limit, and does not
+         * apply to any specific control mode or operation mode.
+         *
+         * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+         * invalid.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.3
+         */
+        maxFlow: FixedAttribute<number | null, any>;
+        /**
+         * This attribute specifies the activity status of the pump functions as listed in PumpStatusBitmap. Where
+         * a pump controller function is active, the corresponding bit shall be set to 1. Where a pump controller
+         * function is not active, the corresponding bit shall be set to 0.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.14
+         */
+        pumpStatus: OptionalAttribute<TypeFromPartialBitSchema<{
+            /**
+             * A fault related to the system or pump device is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 2-16, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.1
+             */
+            deviceFault: BitFlag;
+            /**
+             * A fault related to the supply to the pump is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 0-1 or 13, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.2
+             */
+            supplyFault: BitFlag;
+            /**
+             * Setpoint is too low to achieve.
+             */
+            speedLow: BitFlag;
+            /**
+             * Setpoint is too high to achieve.
+             */
+            speedHigh: BitFlag;
+            /**
+             * Device control is overridden by hardware, such as an external STOP button or via a local HMI.
+             *
+             * While this bit is set, the EffectiveOperationMode is adjusted to Local. Any request changing OperationMode
+             * shall generate a FAILURE error status until LocalOverride is cleared on the physical device. When
+             * LocalOverride is cleared, the device shall return to the operation mode set in OperationMode.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.3
+             */
+            localOverride: BitFlag;
+            /**
+             * Pump is currently running
+             */
+            running: BitFlag;
+            /**
+             * A remote pressure sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantPressure and the setpoint for the pump is interpreted as
+             * a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.4
+             */
+            remotePressure: BitFlag;
+            /**
+             * A remote flow sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantFlow, and the setpoint for the pump is interpreted as a
+             * percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.5
+             */
+            remoteFlow: BitFlag;
+            /**
+             * A remote temperature sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantTemperature, and the setpoint for the pump is
+             * interpreted as a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue])
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.6
+             */
+            remoteTemperature: BitFlag;
+        }>, any>;
+        /**
+         * This attribute specifies current effective operation mode of the pump as defined in OperationModeEnum.
+         *
+         * The value of the EffectiveOperationMode attribute is the same as the OperationMode attribute, unless one
+         * of the following points are true:
+         *
+         *   • The pump is physically set to run with the local settings
+         *
+         *   • The LocalOverride bit in the PumpStatus attribute is set,
+         *
+         * See OperationMode and ControlMode attributes for a detailed description of the operation and control of
+         * the pump.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.15
+         */
+        effectiveOperationMode: Attribute<OperationMode, any>;
+        /**
+         * This attribute specifies the current effective control mode of the pump as defined in ControlModeEnum.
+         *
+         * This attribute contains the control mode that currently applies to the pump. It will have the value of
+         * the ControlMode attribute, unless one of the following points are true:
+         *
+         *   • The ControlMode attribute is set to Automatic. In this case, the value of the EffectiveControlMode
+         *     shall match the behavior of the pump.
+         *
+         *   • A remote sensor is used as the sensor for regulation of the pump. In this case, EffectiveControlMode
+         *     will display ConstantPressure, ConstantFlow or ConstantTemperature if the remote sensor is a
+         *     pressure sensor, a flow sensor or a temperature sensor respectively, regardless of the value of the
+         *     ControlMode attribute.
+         *
+         * In case the ControlMode attribute is not included on the device and no remote sensors are connected, the
+         * value of the EffectiveControlMode shall match the vendor-specific behavior of the pump.
+         *
+         * See OperationMode and ControlMode attributes for detailed a description of the operation and control of
+         * the pump.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.16
+         */
+        effectiveControlMode: Attribute<ControlMode, any>;
+        /**
+         * This attribute specifies the actual capacity of the pump as a percentage of the effective maximum
+         * setpoint value. It is updated dynamically as the speed of the pump changes.
+         *
+         * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+         * attribute will indicate the null value.
+         *
+         * Valid range is 0 % to 163.835% (0.005 % granularity). Although this attribute is a signed value, values
+         * of capacity less than zero have no physical meaning.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.17
+         */
+        capacity: Attribute<number | null, any>;
+        /**
+         * This attribute specifies the actual speed of the pump measured in RPM. It is updated dynamically as the
+         * speed of the pump changes.
+         *
+         * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+         * attribute will indicate the null value.
+         *
+         * Valid range is 0 to 65.534 RPM.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.18
+         */
+        speed: OptionalAttribute<number | null, any>;
+        /**
+         * This attribute specifies the accumulated number of hours that the pump has been powered and the motor
+         * has been running. It is updated dynamically as it increases. It is preserved over power cycles of the
+         * pump. If LifeTimeRunningHours rises above maximum value it “rolls over” and starts at 0 (zero).
+         *
+         * This attribute is writeable, in order to allow setting to an appropriate value after maintenance. If
+         *
+         * the value is not available, this attribute will indicate the null value. Valid range is 0 to 16,777,214
+         * hrs.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.19
+         */
+        lifetimeRunningHours: OptionalWritableAttribute<number | null, any>;
+        /**
+         * This attribute specifies the actual power consumption of the pump in Watts. The value of this attribute
+         * is updated dynamically as the power consumption of the pump changes.
+         *
+         * This attribute is read only. If the value is not available (the measurement of power consumption is not
+         * done in the pump), this attribute will indicate the null value.
+         *
+         * Valid range is 0 to 16,777,214 Watts.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.20
+         */
+        power: OptionalAttribute<number | null, any>;
+        /**
+         * This attribute specifies the accumulated energy consumption of the pump through the entire lifetime of
+         * the pump in kWh. The value of the LifetimeEnergyConsumed attribute is updated dynamically as the energy
+         * consumption of the pump increases. If LifetimeEnergyConsumed rises above maximum value it “rolls over”
+         * and starts at 0 (zero).
+         *
+         * This attribute is writeable, in order to allow setting to an appropriate value after maintenance.
+         *
+         * Valid range is 0 kWh to 4,294,967,294 kWh.
+         *
+         * This attribute shall be null if the value is unknown.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.21
+         */
+        lifetimeEnergyConsumed: OptionalWritableAttribute<number | null, any>;
+        /**
+         * This attribute specifies the operation mode of the pump as defined in OperationModeEnum.
+         *
+         * The actual operating mode of the pump is a result of the setting of the attributes OperationMode,
+         * ControlMode and the optional connection of a remote sensor. The operation and control is prioritized as
+         * shown in the scheme below:
+         *
+         * Priority Scheme of Pump Operation and Control
+         *
+         * If this attribute is Maximum, Minimum or Local, the OperationMode attribute decides how the pump is
+         * operated.
+         *
+         * If this attribute is Normal and a remote sensor is connected to the pump, the type of the remote sensor
+         * decides the control mode of the pump. A connected remote pressure sensor will make the pump run in
+         * control mode Constant pressure and vice versa for flow and temperature type sensors. This is regardless
+         * of the setting of the ControlMode attribute.
+         *
+         * If this attribute is Normal and no remote sensor is connected, the control mode of the pump is decided
+         * by the ControlMode attribute.
+         *
+         * OperationMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+         * point of changing the value of this attribute is vendor-specific.
+         *
+         * In the case a device does not support a specific operation mode, the write interaction to this attribute
+         * with an unsupported operation mode value shall be ignored and a response containing the status of
+         * CONSTRAINT_ERROR shall be returned.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.22
+         */
+        operationMode: WritableAttribute<OperationMode, any>;
+        /**
+         * This attribute specifies the control mode of the pump as defined in ControlModeEnum.
+         *
+         * See the OperationMode attribute for a detailed description of the operation and control of the
+         *
+         * pump.
+         *
+         * ControlMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+         * point of changing is vendor-specific.
+         *
+         * In the case a device does not support a specific control mode, the write interaction to this attribute
+         * with an unsupported control mode value shall be ignored and a response containing the status of
+         * CONSTRAINT_ERROR shall be returned.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.23
+         */
+        controlMode: OptionalWritableAttribute<ControlMode, any>;
+    }, import("../../cluster/Cluster.js").GlobalAttributes<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }>>, import("../../cluster/Cluster.js").Commands, {
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        powerMissingPhase: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        dryRunning: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        motorTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpMotorFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpBlocked: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        sensorFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicNonFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        generalFault: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        leakage: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        airDetection: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        turbineOperation: OptionalEvent<void, any>;
+    }, <T extends ("ConstantPressure" | "CompensatedPressure" | "ConstantFlow" | "ConstantSpeed" | "ConstantTemperature" | "Automatic" | "LocalOperation")[]>(...features_0: T) => Extension<BitFlags<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }, T>>>;
+    type Extension<SF extends TypeFromPartialBitSchema<typeof Base.features>> = ClusterForBaseCluster<typeof Base, SF> & {
+        supportedFeatures: SF;
+    } & (SF extends {
+        constantPressure: true;
+    } ? typeof ConstantPressureComponent : {}) & (SF extends {
+        automatic: true;
+    } ? typeof AutomaticComponent : {}) & (SF extends {
+        compensatedPressure: true;
+    } ? typeof CompensatedPressureComponent : {}) & (SF extends {
+        constantSpeed: true;
+    } ? typeof ConstantSpeedComponent : {}) & (SF extends {
+        constantFlow: true;
+    } ? typeof ConstantFlowComponent : {}) & (SF extends {
+        constantTemperature: true;
+    } ? typeof ConstantTemperatureComponent : {}) & (SF extends {
+        constantPressure: false;
+        compensatedPressure: false;
+        constantFlow: false;
+        constantSpeed: false;
+        constantTemperature: false;
+    } ? never : {});
+    /**
+     * This cluster supports all PumpConfigurationAndControl features. It may support illegal feature combinations.
+     *
+     * If you use this cluster you must manually specify which features are active and ensure the set of active
+     * features is legal per the Matter specification.
+     */
+    const Complete: CreateCluster<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }, TypeFromPartialBitSchema<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }>, import("../../util/Type.js").Merge<{
+        minConstPressure: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, FixedAttribute<number | null, any>>;
+        maxConstPressure: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, FixedAttribute<number | null, any>>;
+        minCompPressure: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        maxCompPressure: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        minConstSpeed: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        maxConstSpeed: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        minConstFlow: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        maxConstFlow: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        minConstTemp: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        maxConstTemp: AsConditional<import("../../schema/BitmapSchema.js").BitSchema, OptionalFixedAttribute<number | null, any>>;
+        maxPressure: FixedAttribute<number | null, any>;
+        maxSpeed: FixedAttribute<number | null, any>;
+        maxFlow: FixedAttribute<number | null, any>;
+        pumpStatus: OptionalAttribute<TypeFromPartialBitSchema<{
+            /**
+             * A fault related to the system or pump device is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 2-16, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.1
+             */
+            deviceFault: BitFlag;
+            /**
+             * A fault related to the supply to the pump is detected.
+             *
+             * If this bit is set, it may correspond to an event in the range 0-1 or 13, see Events.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.2
+             */
+            supplyFault: BitFlag;
+            /**
+             * Setpoint is too low to achieve.
+             */
+            speedLow: BitFlag;
+            /**
+             * Setpoint is too high to achieve.
+             */
+            speedHigh: BitFlag;
+            /**
+             * Device control is overridden by hardware, such as an external STOP button or via a local HMI.
+             *
+             * While this bit is set, the EffectiveOperationMode is adjusted to Local. Any request changing OperationMode
+             * shall generate a FAILURE error status until LocalOverride is cleared on the physical device. When
+             * LocalOverride is cleared, the device shall return to the operation mode set in OperationMode.
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.3
+             */
+            localOverride: BitFlag;
+            /**
+             * Pump is currently running
+             */
+            running: BitFlag;
+            /**
+             * A remote pressure sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantPressure and the setpoint for the pump is interpreted as
+             * a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.4
+             */
+            remotePressure: BitFlag;
+            /**
+             * A remote flow sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantFlow, and the setpoint for the pump is interpreted as a
+             * percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.5
+             */
+            remoteFlow: BitFlag;
+            /**
+             * A remote temperature sensor is used as the sensor for the regulation of the pump.
+             *
+             * If this bit is set, EffectiveControlMode is ConstantTemperature, and the setpoint for the pump is
+             * interpreted as a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue])
+             *
+             * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.6
+             */
+            remoteTemperature: BitFlag;
+        }>, any>;
+        effectiveOperationMode: Attribute<OperationMode, any>;
+        effectiveControlMode: Attribute<ControlMode, any>;
+        capacity: Attribute<number | null, any>;
+        speed: OptionalAttribute<number | null, any>;
+        lifetimeRunningHours: OptionalWritableAttribute<number | null, any>;
+        power: OptionalAttribute<number | null, any>;
+        lifetimeEnergyConsumed: OptionalWritableAttribute<number | null, any>;
+        operationMode: WritableAttribute<OperationMode, any>;
+        controlMode: OptionalWritableAttribute<ControlMode, any>;
+        clusterRevision: Attribute<number, never>;
+        featureMap: Attribute<TypeFromPartialBitSchema<{
+            /**
+             * ConstantPressure
+             *
+             * Supports operating in constant pressure mode
+             */
+            constantPressure: BitFlag;
+            /**
+             * CompensatedPressure
+             *
+             * Supports operating in compensated pressure mode
+             */
+            compensatedPressure: BitFlag;
+            /**
+             * ConstantFlow
+             *
+             * Supports operating in constant flow mode
+             */
+            constantFlow: BitFlag;
+            /**
+             * ConstantSpeed
+             *
+             * Supports operating in constant speed mode
+             */
+            constantSpeed: BitFlag;
+            /**
+             * ConstantTemperature
+             *
+             * Supports operating in constant temperature mode
+             */
+            constantTemperature: BitFlag;
+            /**
+             * Automatic
+             *
+             * Supports operating in automatic mode
+             */
+            automatic: BitFlag;
+            /**
+             * LocalOperation
+             *
+             * Supports operating using local settings
+             */
+            localOperation: BitFlag;
+        }>, never>;
+        attributeList: Attribute<import("../../datatype/AttributeId.js").AttributeId[], never>;
+        eventList: Attribute<import("../../datatype/EventId.js").EventId[], never>;
+        acceptedCommandList: Attribute<import("../../datatype/CommandId.js").CommandId[], never>;
+        generatedCommandList: Attribute<import("../../datatype/CommandId.js").CommandId[], never>;
+    }, import("../../cluster/Cluster.js").GlobalAttributes<{
+        /**
+         * ConstantPressure
+         *
+         * Supports operating in constant pressure mode
+         */
+        constantPressure: BitFlag;
+        /**
+         * CompensatedPressure
+         *
+         * Supports operating in compensated pressure mode
+         */
+        compensatedPressure: BitFlag;
+        /**
+         * ConstantFlow
+         *
+         * Supports operating in constant flow mode
+         */
+        constantFlow: BitFlag;
+        /**
+         * ConstantSpeed
+         *
+         * Supports operating in constant speed mode
+         */
+        constantSpeed: BitFlag;
+        /**
+         * ConstantTemperature
+         *
+         * Supports operating in constant temperature mode
+         */
+        constantTemperature: BitFlag;
+        /**
+         * Automatic
+         *
+         * Supports operating in automatic mode
+         */
+        automatic: BitFlag;
+        /**
+         * LocalOperation
+         *
+         * Supports operating using local settings
+         */
+        localOperation: BitFlag;
+    }>>, {}, {
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        supplyVoltageHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        powerMissingPhase: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureLow: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        systemPressureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        dryRunning: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        motorTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpMotorFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicTemperatureHigh: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        pumpBlocked: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        sensorFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicNonFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        electronicFatalFailure: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        generalFault: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        leakage: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        airDetection: OptionalEvent<void, any>;
+        /**
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+         */
+        turbineOperation: OptionalEvent<void, any>;
+    }>;
+}
+export type PumpConfigurationAndControlCluster = typeof PumpConfigurationAndControl.Cluster;
+export declare const PumpConfigurationAndControlCluster: ExtensibleCluster<{
+    /**
+     * ConstantPressure
+     *
+     * Supports operating in constant pressure mode
+     */
+    constantPressure: BitFlag;
+    /**
+     * CompensatedPressure
+     *
+     * Supports operating in compensated pressure mode
+     */
+    compensatedPressure: BitFlag;
+    /**
+     * ConstantFlow
+     *
+     * Supports operating in constant flow mode
+     */
+    constantFlow: BitFlag;
+    /**
+     * ConstantSpeed
+     *
+     * Supports operating in constant speed mode
+     */
+    constantSpeed: BitFlag;
+    /**
+     * ConstantTemperature
+     *
+     * Supports operating in constant temperature mode
+     */
+    constantTemperature: BitFlag;
+    /**
+     * Automatic
+     *
+     * Supports operating in automatic mode
+     */
+    automatic: BitFlag;
+    /**
+     * LocalOperation
+     *
+     * Supports operating using local settings
+     */
+    localOperation: BitFlag;
+}, TypeFromPartialBitSchema<{
+    /**
+     * ConstantPressure
+     *
+     * Supports operating in constant pressure mode
+     */
+    constantPressure: BitFlag;
+    /**
+     * CompensatedPressure
+     *
+     * Supports operating in compensated pressure mode
+     */
+    compensatedPressure: BitFlag;
+    /**
+     * ConstantFlow
+     *
+     * Supports operating in constant flow mode
+     */
+    constantFlow: BitFlag;
+    /**
+     * ConstantSpeed
+     *
+     * Supports operating in constant speed mode
+     */
+    constantSpeed: BitFlag;
+    /**
+     * ConstantTemperature
+     *
+     * Supports operating in constant temperature mode
+     */
+    constantTemperature: BitFlag;
+    /**
+     * Automatic
+     *
+     * Supports operating in automatic mode
+     */
+    automatic: BitFlag;
+    /**
+     * LocalOperation
+     *
+     * Supports operating using local settings
+     */
+    localOperation: BitFlag;
+}>, import("../../util/Type.js").Merge<{
+    /**
+     * This attribute specifies the maximum pressure the pump can achieve. It is a physical limit, and does not
+     * apply to any specific control mode or operation mode.
+     *
+     * Valid range is -3,276.7 kPa to 3,276.7 kPa (steps of 0.1 kPa). This attribute shall be null if the value
+     * is invalid.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.1
+     */
+    maxPressure: FixedAttribute<number | null, any>;
+    /**
+     * This attribute specifies the maximum speed the pump can achieve. It is a physical limit, and does not
+     * apply to any specific control mode or operation mode.
+     *
+     * Valid range is 0 to 65,534 RPM (steps of 1 RPM). This attribute shall be null if the value is invalid.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.2
+     */
+    maxSpeed: FixedAttribute<number | null, any>;
+    /**
+     * This attribute specifies the maximum flow the pump can achieve. It is a physical limit, and does not
+     * apply to any specific control mode or operation mode.
+     *
+     * Valid range is 0 m/h to 6,553.4 m/h (steps of 0.1 m/h). This attribute shall be null if the value is
+     * invalid.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.3
+     */
+    maxFlow: FixedAttribute<number | null, any>;
+    /**
+     * This attribute specifies the activity status of the pump functions as listed in PumpStatusBitmap. Where
+     * a pump controller function is active, the corresponding bit shall be set to 1. Where a pump controller
+     * function is not active, the corresponding bit shall be set to 0.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.14
+     */
+    pumpStatus: OptionalAttribute<TypeFromPartialBitSchema<{
+        /**
+         * A fault related to the system or pump device is detected.
+         *
+         * If this bit is set, it may correspond to an event in the range 2-16, see Events.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.1
+         */
+        deviceFault: BitFlag;
+        /**
+         * A fault related to the supply to the pump is detected.
+         *
+         * If this bit is set, it may correspond to an event in the range 0-1 or 13, see Events.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.2
+         */
+        supplyFault: BitFlag;
+        /**
+         * Setpoint is too low to achieve.
+         */
+        speedLow: BitFlag;
+        /**
+         * Setpoint is too high to achieve.
+         */
+        speedHigh: BitFlag;
+        /**
+         * Device control is overridden by hardware, such as an external STOP button or via a local HMI.
+         *
+         * While this bit is set, the EffectiveOperationMode is adjusted to Local. Any request changing OperationMode
+         * shall generate a FAILURE error status until LocalOverride is cleared on the physical device. When
+         * LocalOverride is cleared, the device shall return to the operation mode set in OperationMode.
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.3
+         */
+        localOverride: BitFlag;
+        /**
+         * Pump is currently running
+         */
+        running: BitFlag;
+        /**
+         * A remote pressure sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantPressure and the setpoint for the pump is interpreted as
+         * a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.4
+         */
+        remotePressure: BitFlag;
+        /**
+         * A remote flow sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantFlow, and the setpoint for the pump is interpreted as a
+         * percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue]).
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.5
+         */
+        remoteFlow: BitFlag;
+        /**
+         * A remote temperature sensor is used as the sensor for the regulation of the pump.
+         *
+         * If this bit is set, EffectiveControlMode is ConstantTemperature, and the setpoint for the pump is
+         * interpreted as a percentage of the range of the remote sensor ([MinMeasuredValue – MaxMeasuredValue])
+         *
+         * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.6.1.6
+         */
+        remoteTemperature: BitFlag;
+    }>, any>;
+    /**
+     * This attribute specifies current effective operation mode of the pump as defined in OperationModeEnum.
+     *
+     * The value of the EffectiveOperationMode attribute is the same as the OperationMode attribute, unless one
+     * of the following points are true:
+     *
+     *   • The pump is physically set to run with the local settings
+     *
+     *   • The LocalOverride bit in the PumpStatus attribute is set,
+     *
+     * See OperationMode and ControlMode attributes for a detailed description of the operation and control of
+     * the pump.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.15
+     */
+    effectiveOperationMode: Attribute<PumpConfigurationAndControl.OperationMode, any>;
+    /**
+     * This attribute specifies the current effective control mode of the pump as defined in ControlModeEnum.
+     *
+     * This attribute contains the control mode that currently applies to the pump. It will have the value of
+     * the ControlMode attribute, unless one of the following points are true:
+     *
+     *   • The ControlMode attribute is set to Automatic. In this case, the value of the EffectiveControlMode
+     *     shall match the behavior of the pump.
+     *
+     *   • A remote sensor is used as the sensor for regulation of the pump. In this case, EffectiveControlMode
+     *     will display ConstantPressure, ConstantFlow or ConstantTemperature if the remote sensor is a
+     *     pressure sensor, a flow sensor or a temperature sensor respectively, regardless of the value of the
+     *     ControlMode attribute.
+     *
+     * In case the ControlMode attribute is not included on the device and no remote sensors are connected, the
+     * value of the EffectiveControlMode shall match the vendor-specific behavior of the pump.
+     *
+     * See OperationMode and ControlMode attributes for detailed a description of the operation and control of
+     * the pump.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.16
+     */
+    effectiveControlMode: Attribute<PumpConfigurationAndControl.ControlMode, any>;
+    /**
+     * This attribute specifies the actual capacity of the pump as a percentage of the effective maximum
+     * setpoint value. It is updated dynamically as the speed of the pump changes.
+     *
+     * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+     * attribute will indicate the null value.
+     *
+     * Valid range is 0 % to 163.835% (0.005 % granularity). Although this attribute is a signed value, values
+     * of capacity less than zero have no physical meaning.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.17
+     */
+    capacity: Attribute<number | null, any>;
+    /**
+     * This attribute specifies the actual speed of the pump measured in RPM. It is updated dynamically as the
+     * speed of the pump changes.
+     *
+     * If the value is not available (the measurement or estimation of the speed is done in the pump), this
+     * attribute will indicate the null value.
+     *
+     * Valid range is 0 to 65.534 RPM.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.18
+     */
+    speed: OptionalAttribute<number | null, any>;
+    /**
+     * This attribute specifies the accumulated number of hours that the pump has been powered and the motor
+     * has been running. It is updated dynamically as it increases. It is preserved over power cycles of the
+     * pump. If LifeTimeRunningHours rises above maximum value it “rolls over” and starts at 0 (zero).
+     *
+     * This attribute is writeable, in order to allow setting to an appropriate value after maintenance. If
+     *
+     * the value is not available, this attribute will indicate the null value. Valid range is 0 to 16,777,214
+     * hrs.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.19
+     */
+    lifetimeRunningHours: OptionalWritableAttribute<number | null, any>;
+    /**
+     * This attribute specifies the actual power consumption of the pump in Watts. The value of this attribute
+     * is updated dynamically as the power consumption of the pump changes.
+     *
+     * This attribute is read only. If the value is not available (the measurement of power consumption is not
+     * done in the pump), this attribute will indicate the null value.
+     *
+     * Valid range is 0 to 16,777,214 Watts.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.20
+     */
+    power: OptionalAttribute<number | null, any>;
+    /**
+     * This attribute specifies the accumulated energy consumption of the pump through the entire lifetime of
+     * the pump in kWh. The value of the LifetimeEnergyConsumed attribute is updated dynamically as the energy
+     * consumption of the pump increases. If LifetimeEnergyConsumed rises above maximum value it “rolls over”
+     * and starts at 0 (zero).
+     *
+     * This attribute is writeable, in order to allow setting to an appropriate value after maintenance.
+     *
+     * Valid range is 0 kWh to 4,294,967,294 kWh.
+     *
+     * This attribute shall be null if the value is unknown.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.21
+     */
+    lifetimeEnergyConsumed: OptionalWritableAttribute<number | null, any>;
+    /**
+     * This attribute specifies the operation mode of the pump as defined in OperationModeEnum.
+     *
+     * The actual operating mode of the pump is a result of the setting of the attributes OperationMode,
+     * ControlMode and the optional connection of a remote sensor. The operation and control is prioritized as
+     * shown in the scheme below:
+     *
+     * Priority Scheme of Pump Operation and Control
+     *
+     * If this attribute is Maximum, Minimum or Local, the OperationMode attribute decides how the pump is
+     * operated.
+     *
+     * If this attribute is Normal and a remote sensor is connected to the pump, the type of the remote sensor
+     * decides the control mode of the pump. A connected remote pressure sensor will make the pump run in
+     * control mode Constant pressure and vice versa for flow and temperature type sensors. This is regardless
+     * of the setting of the ControlMode attribute.
+     *
+     * If this attribute is Normal and no remote sensor is connected, the control mode of the pump is decided
+     * by the ControlMode attribute.
+     *
+     * OperationMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+     * point of changing the value of this attribute is vendor-specific.
+     *
+     * In the case a device does not support a specific operation mode, the write interaction to this attribute
+     * with an unsupported operation mode value shall be ignored and a response containing the status of
+     * CONSTRAINT_ERROR shall be returned.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.22
+     */
+    operationMode: WritableAttribute<PumpConfigurationAndControl.OperationMode, any>;
+    /**
+     * This attribute specifies the control mode of the pump as defined in ControlModeEnum.
+     *
+     * See the OperationMode attribute for a detailed description of the operation and control of the
+     *
+     * pump.
+     *
+     * ControlMode may be changed at any time, even when the pump is running. The behavior of the pump at the
+     * point of changing is vendor-specific.
+     *
+     * In the case a device does not support a specific control mode, the write interaction to this attribute
+     * with an unsupported control mode value shall be ignored and a response containing the status of
+     * CONSTRAINT_ERROR shall be returned.
+     *
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.7.23
+     */
+    controlMode: OptionalWritableAttribute<PumpConfigurationAndControl.ControlMode, any>;
+}, import("../../cluster/Cluster.js").GlobalAttributes<{
+    /**
+     * ConstantPressure
+     *
+     * Supports operating in constant pressure mode
+     */
+    constantPressure: BitFlag;
+    /**
+     * CompensatedPressure
+     *
+     * Supports operating in compensated pressure mode
+     */
+    compensatedPressure: BitFlag;
+    /**
+     * ConstantFlow
+     *
+     * Supports operating in constant flow mode
+     */
+    constantFlow: BitFlag;
+    /**
+     * ConstantSpeed
+     *
+     * Supports operating in constant speed mode
+     */
+    constantSpeed: BitFlag;
+    /**
+     * ConstantTemperature
+     *
+     * Supports operating in constant temperature mode
+     */
+    constantTemperature: BitFlag;
+    /**
+     * Automatic
+     *
+     * Supports operating in automatic mode
+     */
+    automatic: BitFlag;
+    /**
+     * LocalOperation
+     *
+     * Supports operating using local settings
+     */
+    localOperation: BitFlag;
+}>>, import("../../cluster/Cluster.js").Commands, {
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    supplyVoltageLow: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    supplyVoltageHigh: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    powerMissingPhase: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    systemPressureLow: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    systemPressureHigh: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    dryRunning: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    motorTemperatureHigh: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    pumpMotorFatalFailure: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    electronicTemperatureHigh: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    pumpBlocked: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    sensorFailure: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    electronicNonFatalFailure: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    electronicFatalFailure: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    generalFault: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    leakage: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    airDetection: OptionalEvent<void, any>;
+    /**
+     * @see {@link MatterApplicationClusterSpecificationV1_1} § 4.2.8
+     */
+    turbineOperation: OptionalEvent<void, any>;
+}, <T extends ("ConstantPressure" | "CompensatedPressure" | "ConstantFlow" | "ConstantSpeed" | "ConstantTemperature" | "Automatic" | "LocalOperation")[]>(...features_0: T) => PumpConfigurationAndControl.Extension<BitFlags<{
+    /**
+     * ConstantPressure
+     *
+     * Supports operating in constant pressure mode
+     */
+    constantPressure: BitFlag;
+    /**
+     * CompensatedPressure
+     *
+     * Supports operating in compensated pressure mode
+     */
+    compensatedPressure: BitFlag;
+    /**
+     * ConstantFlow
+     *
+     * Supports operating in constant flow mode
+     */
+    constantFlow: BitFlag;
+    /**
+     * ConstantSpeed
+     *
+     * Supports operating in constant speed mode
+     */
+    constantSpeed: BitFlag;
+    /**
+     * ConstantTemperature
+     *
+     * Supports operating in constant temperature mode
+     */
+    constantTemperature: BitFlag;
+    /**
+     * Automatic
+     *
+     * Supports operating in automatic mode
+     */
+    automatic: BitFlag;
+    /**
+     * LocalOperation
+     *
+     * Supports operating using local settings
+     */
+    localOperation: BitFlag;
+}, T>>>;
+//# sourceMappingURL=PumpConfigurationAndControlCluster.d.ts.map