@alteriom/painlessmesh 1.7.2 → 1.7.4

package/examples/startHere/startHere.ino

@@ -1,159 +1,159 @@
-//************************************************************
-// this is a simple example that uses the easyMesh library
-//
-// 1. blinks led once for every node on the mesh
-// 2. blink cycle repeats every BLINK_PERIOD
-// 3. sends a silly message to every node on the mesh at a random time between 1 and 5 seconds
-// 4. prints anything it receives to Serial.print
-//
-//
-//************************************************************
-#include <painlessMesh.h>
-
-// some gpio pin that is connected to an LED...
-// on my rig, this is 2, change to the right number of your LED.
-#ifndef LED
-  #ifdef LED_BUILTIN
-    #define LED LED_BUILTIN
-  #else
-    #define LED 2
-  #endif
-#endif
-
-#define   BLINK_PERIOD    3000 // milliseconds until cycle repeat
-#define   BLINK_DURATION  100  // milliseconds LED is on for
-
-#define   MESH_SSID       "whateverYouLike"
-#define   MESH_PASSWORD   "somethingSneaky"
-#define   MESH_PORT       5555
-
-// Prototypes
-void sendMessage(); 
-void receivedCallback(uint32_t from, String & msg);
-void newConnectionCallback(uint32_t nodeId);
-void changedConnectionCallback(); 
-void nodeTimeAdjustedCallback(int32_t offset); 
-void delayReceivedCallback(uint32_t from, int32_t delay);
-
-Scheduler     userScheduler; // to control your personal task
-painlessMesh  mesh;
-
-bool calc_delay = false;
-SimpleList<uint32_t> nodes;
-
-void sendMessage() ; // Prototype
-Task taskSendMessage( TASK_SECOND * 1, TASK_FOREVER, &sendMessage ); // start with a one second interval
-
-// Task to blink the number of nodes
-Task blinkNoNodes;
-bool onFlag = false;
-
-void setup() {
-  Serial.begin(115200);
-
-  pinMode(LED, OUTPUT);
-
-  mesh.setDebugMsgTypes(ERROR | DEBUG);  // set before init() so that you can see error messages
-
-  mesh.init(MESH_SSID, MESH_PASSWORD, &userScheduler, MESH_PORT);
-  mesh.onReceive(&receivedCallback);
-  mesh.onNewConnection(&newConnectionCallback);
-  mesh.onChangedConnections(&changedConnectionCallback);
-  mesh.onNodeTimeAdjusted(&nodeTimeAdjustedCallback);
-  mesh.onNodeDelayReceived(&delayReceivedCallback);
-
-  userScheduler.addTask( taskSendMessage );
-  taskSendMessage.enable();
-
-  blinkNoNodes.set(BLINK_PERIOD, (mesh.getNodeList().size() + 1) * 2, []() {
-      // If on, switch off, else switch on
-      if (onFlag)
-        onFlag = false;
-      else
-        onFlag = true;
-      blinkNoNodes.delay(BLINK_DURATION);
-
-      if (blinkNoNodes.isLastIteration()) {
-        // Finished blinking. Reset task for next run 
-        // blink number of nodes (including this node) times
-        blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
-        // Calculate delay based on current mesh time and BLINK_PERIOD
-        // This results in blinks between nodes being synced
-        blinkNoNodes.enableDelayed(BLINK_PERIOD - 
-            (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
-      }
-  });
-  userScheduler.addTask(blinkNoNodes);
-  blinkNoNodes.enable();
-
-  randomSeed(analogRead(A0));
-}
-
-void loop() {
-  mesh.update();
-  digitalWrite(LED, !onFlag);
-}
-
-void sendMessage() {
-  String msg = "Hello from node ";
-  msg += mesh.getNodeId();
-  msg += " myFreeMemory: " + String(ESP.getFreeHeap());
-  mesh.sendBroadcast(msg);
-
-  if (calc_delay) {
-    SimpleList<uint32_t>::iterator node = nodes.begin();
-    while (node != nodes.end()) {
-      mesh.startDelayMeas(*node);
-      node++;
-    }
-    calc_delay = false;
-  }
-
-  Serial.printf("Sending message: %s\n", msg.c_str());
-  
-  taskSendMessage.setInterval( random(TASK_SECOND * 1, TASK_SECOND * 5));  // between 1 and 5 seconds
-}
-
-
-void receivedCallback(uint32_t from, String & msg) {
-  Serial.printf("startHere: Received from %u msg=%s\n", from, msg.c_str());
-}
-
-void newConnectionCallback(uint32_t nodeId) {
-  // Reset blink task
-  onFlag = false;
-  blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
-  blinkNoNodes.enableDelayed(BLINK_PERIOD - (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
- 
-  Serial.printf("--> startHere: New Connection, nodeId = %u\n", nodeId);
-  Serial.printf("--> startHere: New Connection, %s\n", mesh.subConnectionJson(true).c_str());
-}
-
-void changedConnectionCallback() {
-  Serial.printf("Changed connections\n");
-  // Reset blink task
-  onFlag = false;
-  blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
-  blinkNoNodes.enableDelayed(BLINK_PERIOD - (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
- 
-  nodes = mesh.getNodeList();
-
-  Serial.printf("Num nodes: %d\n", nodes.size());
-  Serial.printf("Connection list:");
-
-  SimpleList<uint32_t>::iterator node = nodes.begin();
-  while (node != nodes.end()) {
-    Serial.printf(" %u", *node);
-    node++;
-  }
-  Serial.println();
-  calc_delay = true;
-}
-
-void nodeTimeAdjustedCallback(int32_t offset) {
-  Serial.printf("Adjusted time %u. Offset = %d\n", mesh.getNodeTime(), offset);
-}
-
-void delayReceivedCallback(uint32_t from, int32_t delay) {
-  Serial.printf("Delay to node %u is %d us\n", from, delay);
-}
+//************************************************************
+// this is a simple example that uses the easyMesh library
+//
+// 1. blinks led once for every node on the mesh
+// 2. blink cycle repeats every BLINK_PERIOD
+// 3. sends a silly message to every node on the mesh at a random time between 1 and 5 seconds
+// 4. prints anything it receives to Serial.print
+//
+//
+//************************************************************
+#include <painlessMesh.h>
+
+// some gpio pin that is connected to an LED...
+// on my rig, this is 2, change to the right number of your LED.
+#ifndef LED
+  #ifdef LED_BUILTIN
+    #define LED LED_BUILTIN
+  #else
+    #define LED 2
+  #endif
+#endif
+
+#define   BLINK_PERIOD    3000 // milliseconds until cycle repeat
+#define   BLINK_DURATION  100  // milliseconds LED is on for
+
+#define   MESH_SSID       "whateverYouLike"
+#define   MESH_PASSWORD   "somethingSneaky"
+#define   MESH_PORT       5555
+
+// Prototypes
+void sendMessage(); 
+void receivedCallback(uint32_t from, String & msg);
+void newConnectionCallback(uint32_t nodeId);
+void changedConnectionCallback(); 
+void nodeTimeAdjustedCallback(int32_t offset); 
+void delayReceivedCallback(uint32_t from, int32_t delay);
+
+Scheduler     userScheduler; // to control your personal task
+painlessMesh  mesh;
+
+bool calc_delay = false;
+SimpleList<uint32_t> nodes;
+
+void sendMessage() ; // Prototype
+Task taskSendMessage( TASK_SECOND * 1, TASK_FOREVER, &sendMessage ); // start with a one second interval
+
+// Task to blink the number of nodes
+Task blinkNoNodes;
+bool onFlag = false;
+
+void setup() {
+  Serial.begin(115200);
+
+  pinMode(LED, OUTPUT);
+
+  mesh.setDebugMsgTypes(ERROR | DEBUG);  // set before init() so that you can see error messages
+
+  mesh.init(MESH_SSID, MESH_PASSWORD, &userScheduler, MESH_PORT);
+  mesh.onReceive(&receivedCallback);
+  mesh.onNewConnection(&newConnectionCallback);
+  mesh.onChangedConnections(&changedConnectionCallback);
+  mesh.onNodeTimeAdjusted(&nodeTimeAdjustedCallback);
+  mesh.onNodeDelayReceived(&delayReceivedCallback);
+
+  userScheduler.addTask( taskSendMessage );
+  taskSendMessage.enable();
+
+  blinkNoNodes.set(BLINK_PERIOD, (mesh.getNodeList().size() + 1) * 2, []() {
+      // If on, switch off, else switch on
+      if (onFlag)
+        onFlag = false;
+      else
+        onFlag = true;
+      blinkNoNodes.delay(BLINK_DURATION);
+
+      if (blinkNoNodes.isLastIteration()) {
+        // Finished blinking. Reset task for next run 
+        // blink number of nodes (including this node) times
+        blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
+        // Calculate delay based on current mesh time and BLINK_PERIOD
+        // This results in blinks between nodes being synced
+        blinkNoNodes.enableDelayed(BLINK_PERIOD - 
+            (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
+      }
+  });
+  userScheduler.addTask(blinkNoNodes);
+  blinkNoNodes.enable();
+
+  randomSeed(analogRead(A0));
+}
+
+void loop() {
+  mesh.update();
+  digitalWrite(LED, !onFlag);
+}
+
+void sendMessage() {
+  String msg = "Hello from node ";
+  msg += mesh.getNodeId();
+  msg += " myFreeMemory: " + String(ESP.getFreeHeap());
+  mesh.sendBroadcast(msg);
+
+  if (calc_delay) {
+    SimpleList<uint32_t>::iterator node = nodes.begin();
+    while (node != nodes.end()) {
+      mesh.startDelayMeas(*node);
+      node++;
+    }
+    calc_delay = false;
+  }
+
+  Serial.printf("Sending message: %s\n", msg.c_str());
+  
+  taskSendMessage.setInterval( random(TASK_SECOND * 1, TASK_SECOND * 5));  // between 1 and 5 seconds
+}
+
+
+void receivedCallback(uint32_t from, String & msg) {
+  Serial.printf("startHere: Received from %u msg=%s\n", from, msg.c_str());
+}
+
+void newConnectionCallback(uint32_t nodeId) {
+  // Reset blink task
+  onFlag = false;
+  blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
+  blinkNoNodes.enableDelayed(BLINK_PERIOD - (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
+ 
+  Serial.printf("--> startHere: New Connection, nodeId = %u\n", nodeId);
+  Serial.printf("--> startHere: New Connection, %s\n", mesh.subConnectionJson(true).c_str());
+}
+
+void changedConnectionCallback() {
+  Serial.printf("Changed connections\n");
+  // Reset blink task
+  onFlag = false;
+  blinkNoNodes.setIterations((mesh.getNodeList().size() + 1) * 2);
+  blinkNoNodes.enableDelayed(BLINK_PERIOD - (mesh.getNodeTime() % (BLINK_PERIOD*1000))/1000);
+ 
+  nodes = mesh.getNodeList();
+
+  Serial.printf("Num nodes: %d\n", nodes.size());
+  Serial.printf("Connection list:");
+
+  SimpleList<uint32_t>::iterator node = nodes.begin();
+  while (node != nodes.end()) {
+    Serial.printf(" %u", *node);
+    node++;
+  }
+  Serial.println();
+  calc_delay = true;
+}
+
+void nodeTimeAdjustedCallback(int32_t offset) {
+  Serial.printf("Adjusted time %u. Offset = %d\n", mesh.getNodeTime(), offset);
+}
+
+void delayReceivedCallback(uint32_t from, int32_t delay) {
+  Serial.printf("Delay to node %u is %d us\n", from, delay);
+}

package/examples/webServer/platformio.ini

@@ -1,27 +1,27 @@
-[platformio]
-src_dir = .
-
-[env]
-lib_deps =
-    bblanchon/ArduinoJson
-    arkhipenko/TaskScheduler
-    esp32async/ESPAsyncWebServer
-
-[env:esp8266]
-platform = espressif8266
-board = nodemcuv2
-framework = arduino
-lib_extra_dirs = ../../
-lib_deps =
-    ${env.lib_deps}  ; Inherit common dependencies
-    esp32async/ESPAsyncTCP  ; Only for ESP8266
-
-[env:esp32]
-platform = espressif32
-board = esp32dev
-framework = arduino
-lib_extra_dirs = ../../
-lib_deps =
-    ${env.lib_deps}  ; Inherit common dependencies
-    esp32async/AsyncTCP
-    AsyncWebServer
+[platformio]
+src_dir = .
+
+[env]
+lib_deps =
+    bblanchon/ArduinoJson
+    arkhipenko/TaskScheduler
+    esp32async/ESPAsyncWebServer
+
+[env:esp8266]
+platform = espressif8266
+board = nodemcuv2
+framework = arduino
+lib_extra_dirs = ../../
+lib_deps =
+    ${env.lib_deps}  ; Inherit common dependencies
+    esp32async/ESPAsyncTCP  ; Only for ESP8266
+
+[env:esp32]
+platform = espressif32
+board = esp32dev
+framework = arduino
+lib_extra_dirs = ../../
+lib_deps =
+    ${env.lib_deps}  ; Inherit common dependencies
+    esp32async/AsyncTCP
+    AsyncWebServer

package/examples/webServer/webServer.ino

@@ -1,89 +1,89 @@
-//************************************************************
-// this is a simple example that uses the painlessMesh library to
-// connect to a another network and broadcast message from a webpage to the edges of the mesh network.
-// This sketch can be extended further using all the abilities of the AsyncWebserver library (WS, events, ...)
-// for more details
-// https://gitlab.com/painlessMesh/painlessMesh/wikis/bridge-between-mesh-and-another-network
-// for more details about my version
-// https://gitlab.com/Assassynv__V/painlessMesh
-// and for more details about the AsyncWebserver library
-// https://github.com/me-no-dev/ESPAsyncWebServer
-//************************************************************
-
-#include "IPAddress.h"
-#include "painlessMesh.h"
-
-#ifdef ESP8266
-#include "Hash.h"
-#include <ESPAsyncTCP.h>
-#else
-#include <AsyncTCP.h>
-#endif
-#include <ESPAsyncWebServer.h>
-
-#define   MESH_PREFIX     "whateverYouLike"
-#define   MESH_PASSWORD   "somethingSneaky"
-#define   MESH_PORT       5555
-
-#define   STATION_SSID     "mySSID"
-#define   STATION_PASSWORD "myPASSWORD"
-
-#define HOSTNAME "HTTP_BRIDGE"
-
-// Prototype
-void receivedCallback( const uint32_t &from, const String &msg );
-IPAddress getlocalIP();
-
-painlessMesh  mesh;
-AsyncWebServer server(80);
-IPAddress myIP(0,0,0,0);
-IPAddress myAPIP(0,0,0,0);
-
-void setup() {
-  Serial.begin(115200);
-
-  mesh.setDebugMsgTypes( ERROR | STARTUP | CONNECTION );  // set before init() so that you can see startup messages
-
-  // Channel set to 6. Make sure to use the same channel for your mesh and for you other
-  // network (STATION_SSID)
-  mesh.init( MESH_PREFIX, MESH_PASSWORD, MESH_PORT, WIFI_AP_STA, 6 );
-  mesh.onReceive(&receivedCallback);
-
-  mesh.stationManual(STATION_SSID, STATION_PASSWORD);
-  mesh.setHostname(HOSTNAME);
-
-  // Bridge node, should (in most cases) be a root node. See [the wiki](https://gitlab.com/painlessMesh/painlessMesh/wikis/Possible-challenges-in-mesh-formation) for some background
-  mesh.setRoot(true);
-  // This node and all other nodes should ideally know the mesh contains a root, so call this on all nodes
-  mesh.setContainsRoot(true);
-
-  myAPIP = IPAddress(mesh.getAPIP());
-  Serial.println("My AP IP is " + myAPIP.toString());
-
-  //Async webserver
-  server.on("/", HTTP_GET, [](AsyncWebServerRequest *request){
-    request->send(200, "text/html", "<form>Text to Broadcast<br><input type='text' name='BROADCAST'><br><br><input type='submit' value='Submit'></form>");
-    if (request->hasArg("BROADCAST")){
-      String msg = request->arg("BROADCAST");
-      mesh.sendBroadcast(msg);
-    }
-  });
-  server.begin();
-
-}
-
-void loop() {
-  mesh.update();
-  if(myIP != getlocalIP()){
-    myIP = getlocalIP();
-    Serial.println("My IP is " + myIP.toString());
-  }
-}
-
-void receivedCallback( const uint32_t &from, const String &msg ) {
-  Serial.printf("bridge: Received from %u msg=%s\n", from, msg.c_str());
-}
-
-IPAddress getlocalIP() {
-  return IPAddress(mesh.getStationIP());
-}
+//************************************************************
+// this is a simple example that uses the painlessMesh library to
+// connect to a another network and broadcast message from a webpage to the edges of the mesh network.
+// This sketch can be extended further using all the abilities of the AsyncWebserver library (WS, events, ...)
+// for more details
+// https://gitlab.com/painlessMesh/painlessMesh/wikis/bridge-between-mesh-and-another-network
+// for more details about my version
+// https://gitlab.com/Assassynv__V/painlessMesh
+// and for more details about the AsyncWebserver library
+// https://github.com/me-no-dev/ESPAsyncWebServer
+//************************************************************
+
+#include "IPAddress.h"
+#include "painlessMesh.h"
+
+#ifdef ESP8266
+#include "Hash.h"
+#include <ESPAsyncTCP.h>
+#else
+#include <AsyncTCP.h>
+#endif
+#include <ESPAsyncWebServer.h>
+
+#define   MESH_PREFIX     "whateverYouLike"
+#define   MESH_PASSWORD   "somethingSneaky"
+#define   MESH_PORT       5555
+
+#define   STATION_SSID     "mySSID"
+#define   STATION_PASSWORD "myPASSWORD"
+
+#define HOSTNAME "HTTP_BRIDGE"
+
+// Prototype
+void receivedCallback( const uint32_t &from, const String &msg );
+IPAddress getlocalIP();
+
+painlessMesh  mesh;
+AsyncWebServer server(80);
+IPAddress myIP(0,0,0,0);
+IPAddress myAPIP(0,0,0,0);
+
+void setup() {
+  Serial.begin(115200);
+
+  mesh.setDebugMsgTypes( ERROR | STARTUP | CONNECTION );  // set before init() so that you can see startup messages
+
+  // Channel set to 6. Make sure to use the same channel for your mesh and for you other
+  // network (STATION_SSID)
+  mesh.init( MESH_PREFIX, MESH_PASSWORD, MESH_PORT, WIFI_AP_STA, 6 );
+  mesh.onReceive(&receivedCallback);
+
+  mesh.stationManual(STATION_SSID, STATION_PASSWORD);
+  mesh.setHostname(HOSTNAME);
+
+  // Bridge node, should (in most cases) be a root node. See [the wiki](https://gitlab.com/painlessMesh/painlessMesh/wikis/Possible-challenges-in-mesh-formation) for some background
+  mesh.setRoot(true);
+  // This node and all other nodes should ideally know the mesh contains a root, so call this on all nodes
+  mesh.setContainsRoot(true);
+
+  myAPIP = IPAddress(mesh.getAPIP());
+  Serial.println("My AP IP is " + myAPIP.toString());
+
+  //Async webserver
+  server.on("/", HTTP_GET, [](AsyncWebServerRequest *request){
+    request->send(200, "text/html", "<form>Text to Broadcast<br><input type='text' name='BROADCAST'><br><br><input type='submit' value='Submit'></form>");
+    if (request->hasArg("BROADCAST")){
+      String msg = request->arg("BROADCAST");
+      mesh.sendBroadcast(msg);
+    }
+  });
+  server.begin();
+
+}
+
+void loop() {
+  mesh.update();
+  if(myIP != getlocalIP()){
+    myIP = getlocalIP();
+    Serial.println("My IP is " + myIP.toString());
+  }
+}
+
+void receivedCallback( const uint32_t &from, const String &msg ) {
+  Serial.printf("bridge: Received from %u msg=%s\n", from, msg.c_str());
+}
+
+IPAddress getlocalIP() {
+  return IPAddress(mesh.getStationIP());
+}

package/keywords.txt

@@ -1,49 +1,49 @@
-# painlessMesh library keywords
-
-# Classes (KEYWORD1)
-painlessMesh	KEYWORD1
-Scheduler	KEYWORD1
-Task	KEYWORD1
-
-# Methods and Functions (KEYWORD2)
-init	KEYWORD2
-update	KEYWORD2
-sendBroadcast	KEYWORD2
-sendSingle	KEYWORD2
-onReceive	KEYWORD2
-onNewConnection	KEYWORD2
-onChangedConnections	KEYWORD2
-onNodeTimeAdjusted	KEYWORD2
-getNodeList	KEYWORD2
-getNodeId	KEYWORD2
-getNodeTime	KEYWORD2
-setDebugMsgTypes	KEYWORD2
-subConnectionJson	KEYWORD2
-asNodeTree	KEYWORD2
-
-# Alteriom Extensions (KEYWORD1)
-SensorPackage	KEYWORD1
-CommandPackage	KEYWORD1
-StatusPackage	KEYWORD1
-
-# Alteriom Methods (KEYWORD2)
-addTo	KEYWORD2
-jsonObjectSize	KEYWORD2
-
-# Constants (LITERAL1)
-MESH_PREFIX	LITERAL1
-MESH_PASSWORD	LITERAL1
-MESH_PORT	LITERAL1
-TASK_SECOND	LITERAL1
-TASK_MINUTE	LITERAL1
-TASK_HOUR	LITERAL1
-TASK_FOREVER	LITERAL1
-ERROR	LITERAL1
-STARTUP	LITERAL1
-CONNECTION	LITERAL1
-SYNC	LITERAL1
-COMMUNICATION	LITERAL1
-GENERAL	LITERAL1
-MSG_TYPES	LITERAL1
-REMOTE	LITERAL1
+# painlessMesh library keywords
+
+# Classes (KEYWORD1)
+painlessMesh	KEYWORD1
+Scheduler	KEYWORD1
+Task	KEYWORD1
+
+# Methods and Functions (KEYWORD2)
+init	KEYWORD2
+update	KEYWORD2
+sendBroadcast	KEYWORD2
+sendSingle	KEYWORD2
+onReceive	KEYWORD2
+onNewConnection	KEYWORD2
+onChangedConnections	KEYWORD2
+onNodeTimeAdjusted	KEYWORD2
+getNodeList	KEYWORD2
+getNodeId	KEYWORD2
+getNodeTime	KEYWORD2
+setDebugMsgTypes	KEYWORD2
+subConnectionJson	KEYWORD2
+asNodeTree	KEYWORD2
+
+# Alteriom Extensions (KEYWORD1)
+SensorPackage	KEYWORD1
+CommandPackage	KEYWORD1
+StatusPackage	KEYWORD1
+
+# Alteriom Methods (KEYWORD2)
+addTo	KEYWORD2
+jsonObjectSize	KEYWORD2
+
+# Constants (LITERAL1)
+MESH_PREFIX	LITERAL1
+MESH_PASSWORD	LITERAL1
+MESH_PORT	LITERAL1
+TASK_SECOND	LITERAL1
+TASK_MINUTE	LITERAL1
+TASK_HOUR	LITERAL1
+TASK_FOREVER	LITERAL1
+ERROR	LITERAL1
+STARTUP	LITERAL1
+CONNECTION	LITERAL1
+SYNC	LITERAL1
+COMMUNICATION	LITERAL1
+GENERAL	LITERAL1
+MSG_TYPES	LITERAL1
+REMOTE	LITERAL1
 DEBUG	LITERAL1