@alteriom/painlessmesh 1.7.4 → 1.7.6

package/docs/troubleshooting/common-issues.md

@@ -1,521 +1,521 @@
-# Common Issues and Solutions
-
-This guide covers the most frequently encountered problems when working with painlessMesh and their solutions.
-
-## Connection Issues
-
-### Nodes Not Connecting
-
-**Symptoms:**
-- Nodes don't appear in each other's node lists
-- No "New Connection" messages in serial output
-- Mesh remains disconnected
-
-**Solutions:**
-
-#### 1. Check Network Credentials
-Ensure all nodes use identical network settings:
-
-```cpp
-// These MUST be identical on all nodes
-#define MESH_PREFIX     "MyMeshNetwork"    // Exact match required
-#define MESH_PASSWORD   "password123"      // Case sensitive
-#define MESH_PORT       5555               // Must match
-```
-
-#### 2. Verify WiFi Range
-- Nodes must be within WiFi range (typically 50-200m)
-- Check for interference from other 2.4GHz devices
-- Try moving nodes closer together for testing
-
-#### 3. Check Serial Output
-Enable connection debugging:
-
-```cpp
-mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION);
-```
-
-Look for error messages like:
-- "Failed to connect to mesh"
-- "Connection timeout"
-- "Authentication failed"
-
-#### 4. Reset Network Settings
-Clear stored WiFi credentials:
-
-```cpp
-void setup() {
-    // Add this before mesh.init()
-    WiFi.disconnect(true);  // Clear stored networks
-    delay(1000);
-    
-    mesh.init(MESH_PREFIX, MESH_PASSWORD, &userScheduler, MESH_PORT);
-}
-```
-
-### Frequent Disconnections
-
-**Symptoms:**
-- Nodes connect but disconnect shortly after
-- Repeated "Connection dropped" messages
-- Unstable mesh topology
-
-**Solutions:**
-
-#### 1. Check Power Supply
-- Ensure stable power supply (USB power can be insufficient)
-- Use adequate power adapters (≥1A for ESP32, ≥500mA for ESP8266)
-- Check for voltage drops during WiFi transmission
-
-#### 2. Reduce Connection Load
-Limit the number of simultaneous connections:
-
-```cpp
-// Reduce connection count on ESP8266
-#define MAX_CONN 2  // Instead of default 4
-```
-
-#### 3. Increase Connection Timeout
-```cpp
-// Extend connection timeouts
-#define CONNECTION_TIMEOUT 60000  // 60 seconds instead of 30
-```
-
-#### 4. Memory Issues
-Monitor memory usage:
-
-```cpp
-void checkMemory() {
-    Serial.printf("Free heap: %d bytes\n", ESP.getFreeHeap());
-    if (ESP.getFreeHeap() < 10000) {  // ESP32
-        Serial.println("WARNING: Low memory!");
-    }
-}
-```
-
-## Message Delivery Issues
-
-### Messages Not Being Received
-
-**Symptoms:**
-- `sendBroadcast()` returns `true` but messages don't arrive
-- Callbacks not triggered
-- Silent message failures
-
-**Solutions:**
-
-#### 1. Check Callback Registration
-Ensure callbacks are set before `mesh.init()`:
-
-```cpp
-void setup() {
-    Serial.begin(115200);
-    
-    // Set callbacks BEFORE init
-    mesh.onReceive(&receivedCallback);
-    mesh.onNewConnection(&newConnectionCallback);
-    
-    // Then initialize
-    mesh.init(MESH_PREFIX, MESH_PASSWORD, &userScheduler, MESH_PORT);
-}
-```
-
-#### 2. Verify Message Format
-Check JSON formatting for custom messages:
-
-```cpp
-void sendSensorData() {
-    // Proper JSON formatting
-    String msg = "{";
-    msg += "\"type\":\"sensor\",";
-    msg += "\"value\":" + String(sensorValue) + ",";
-    msg += "\"timestamp\":" + String(mesh.getNodeTime());
-    msg += "}";  // Don't forget closing brace
-    
-    mesh.sendBroadcast(msg);
-}
-```
-
-#### 3. Enable Communication Debugging
-```cpp
-mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION | COMMUNICATION);
-```
-
-#### 4. Check Network Congestion
-Reduce message frequency if network is congested:
-
-```cpp
-// Instead of every second
-Task taskSendMessage(10000, TASK_FOREVER, &sendMessage);  // Every 10 seconds
-```
-
-### Large Messages Being Dropped
-
-**Symptoms:**
-- Small messages work, large ones don't
-- Memory errors in serial output
-- Random message failures
-
-**Solutions:**
-
-#### 1. Reduce Message Size
-```cpp
-// Keep messages under 1KB for reliability
-String createMessage() {
-    String msg = "{\"data\":\"";
-    msg += shortData; // Keep data concise
-    msg += "\"}";
-    
-    if (msg.length() > 1000) {
-        Serial.println("Warning: Message too large");
-        return "{}"; // Send empty object
-    }
-    
-    return msg;
-}
-```
-
-#### 2. Split Large Data
-```cpp
-void sendLargeData(String largeData) {
-    const size_t chunkSize = 500;
-    
-    for (size_t i = 0; i < largeData.length(); i += chunkSize) {
-        String chunk = largeData.substring(i, i + chunkSize);
-        String msg = "{\"chunk\":" + String(i/chunkSize) + ",\"data\":\"" + chunk + "\"}";
-        mesh.sendBroadcast(msg);
-        delay(100); // Small delay between chunks
-    }
-}
-```
-
-## Memory Issues
-
-### ESP8266 Memory Limitations
-
-**Symptoms:**
-- Frequent crashes or resets
-- "Out of memory" errors
-- Unstable behavior under load
-
-**Solutions:**
-
-#### 1. Reduce Buffer Sizes
-```cpp
-// Use smaller JSON documents
-DynamicJsonDocument doc(512);  // Instead of 1024 or larger
-
-// Limit string sizes
-TSTRING deviceName;
-deviceName.reserve(32);  // Pre-allocate reasonable size
-```
-
-#### 2. Limit Concurrent Connections
-```cpp
-#define MAX_CONN 2  // ESP8266 works best with 2-3 connections
-```
-
-#### 3. Optimize Task Usage
-```cpp
-// Combine multiple tasks into one
-Task taskMultiFunction(30000, TASK_FOREVER, [](){
-    sendSensorData();
-    checkStatus();
-    cleanupMemory();
-});
-```
-
-#### 4. Implement Memory Monitoring
-```cpp
-void monitorMemory() {
-    uint32_t freeHeap = ESP.getFreeHeap();
-    Serial.printf("Free heap: %u bytes\n", freeHeap);
-    
-    if (freeHeap < 5000) {  // Critical threshold for ESP8266
-        Serial.println("CRITICAL: Very low memory!");
-        // Take corrective action
-        mesh.stop();
-        delay(1000);
-        ESP.restart();
-    }
-}
-```
-
-### ESP32 Memory Issues
-
-**Symptoms:**
-- Slower performance over time
-- Memory leaks
-- Task watchdog timeouts
-
-**Solutions:**
-
-#### 1. Monitor Heap Fragmentation
-```cpp
-void checkHeapHealth() {
-    Serial.printf("Free heap: %u bytes\n", ESP.getFreeHeap());
-    Serial.printf("Largest block: %u bytes\n", ESP.getMaxAllocHeap());
-    
-    // If largest block is much smaller than free heap, 
-    // heap is fragmented
-    if (ESP.getMaxAllocHeap() < ESP.getFreeHeap() / 2) {
-        Serial.println("Warning: Heap fragmentation detected");
-    }
-}
-```
-
-#### 2. Use Static Allocation When Possible
-```cpp
-// Instead of dynamic allocation
-StaticJsonDocument<1024> doc;  // Pre-allocated
-
-// Or use stack allocation for small objects
-char buffer[256];
-snprintf(buffer, sizeof(buffer), "{\"value\":%d}", value);
-```
-
-## Compilation Issues
-
-### Library Not Found
-
-**Symptoms:**
-- "painlessMesh.h: No such file or directory"
-- Library compilation errors
-
-**Solutions:**
-
-#### 1. Arduino IDE
-- Go to **Sketch → Include Library → Manage Libraries**
-- Search for "painlessMesh" and install latest version
-- Ensure ArduinoJson and TaskScheduler are also installed
-
-#### 2. PlatformIO
-Add to `platformio.ini`:
-```ini
-lib_deps = 
-    painlessMesh
-    bblanchon/ArduinoJson@^6.21.3
-    arkhipenko/TaskScheduler@^3.7.0
-```
-
-### Version Compatibility Issues
-
-**Symptoms:**
-- Compilation errors after library updates
-- API function not found errors
-- Deprecated warnings
-
-**Solutions:**
-
-#### 1. Check Version Compatibility
-```cpp
-// Check painlessMesh version
-#include "painlessMesh.h"
-Serial.printf("painlessMesh version: %s\n", PAINLESSMESH_VERSION);
-```
-
-#### 2. Lock Library Versions
-In `platformio.ini`:
-```ini
-lib_deps = 
-    painlessMesh@1.5.0        # Lock to specific version
-    bblanchon/ArduinoJson@6.21.3
-    arkhipenko/TaskScheduler@3.7.0
-```
-
-#### 3. Update Deprecated APIs
-```cpp
-// Old API (deprecated)
-mesh.onReceive(&receivedCallback);
-
-// New API (if changed in your version)
-mesh.onReceive([](uint32_t from, String& msg) {
-    receivedCallback(from, msg);
-});
-```
-
-## Performance Issues
-
-### Slow Message Delivery
-
-**Symptoms:**
-- Messages take several seconds to arrive
-- High latency in mesh communication
-- Sluggish response times
-
-**Solutions:**
-
-#### 1. Check Network Topology
-```cpp
-void printTopology() {
-    String topology = mesh.subConnectionJson(true);
-    Serial.println("Current topology:");
-    Serial.println(topology);
-    
-    // Look for long chains or star topologies
-    // Optimal: balanced tree with short paths
-}
-```
-
-#### 2. Reduce Message Frequency
-```cpp
-// Instead of high frequency
-Task taskFastSender(1000, TASK_FOREVER, &sendMessage);  // Every second
-
-// Use lower frequency
-Task taskSlowSender(10000, TASK_FOREVER, &sendMessage); // Every 10 seconds
-```
-
-#### 3. Optimize Message Size
-```cpp
-// Compact JSON formatting
-String createOptimizedMessage() {
-    // Use short field names
-    String msg = "{\"t\":" + String(temp) + ",\"h\":" + String(hum) + "}";
-    return msg;
-}
-```
-
-### High CPU Usage
-
-**Symptoms:**
-- ESP becomes hot during operation
-- Watchdog timer resets
-- Sluggish response to other tasks
-
-**Solutions:**
-
-#### 1. Add Delays in Tight Loops
-```cpp
-void loop() {
-    mesh.update();
-    
-    // Add small delay to prevent CPU overload
-    delay(10);
-    
-    // Or yield to other tasks
-    yield();
-}
-```
-
-#### 2. Reduce Debug Output
-```cpp
-// Only use essential debug messages in production
-mesh.setDebugMsgTypes(ERROR);  // Only errors
-```
-
-#### 3. Optimize Task Scheduling
-```cpp
-// Spread tasks over time
-Task task1(30000, TASK_FOREVER, &function1);     // Every 30s
-Task task2(35000, TASK_FOREVER, &function2);     // Every 35s (offset)
-Task task3(40000, TASK_FOREVER, &function3);     // Every 40s
-```
-
-## Platform-Specific Issues
-
-### ESP8266 Specific
-
-**Reset Loops:**
-```cpp
-// Increase watchdog timeout
-ESP.wdtDisable();
-// Perform long operations
-ESP.wdtEnable(5000);  // 5 second timeout
-```
-
-**Flash Memory Issues:**
-```cpp
-// Check flash size
-Serial.printf("Flash size: %u bytes\n", ESP.getFlashChipSize());
-
-// Ensure adequate space for SPIFFS/LittleFS
-// Reserve at least 64KB for filesystem
-```
-
-### ESP32 Specific
-
-**Core Affinity:**
-```cpp
-// Pin mesh tasks to specific core if needed
-void setup() {
-    // Use core 0 for mesh (core 1 for app)
-    xTaskCreatePinnedToCore(meshTask, "MeshTask", 8192, NULL, 1, NULL, 0);
-}
-```
-
-**Partition Scheme:**
-Ensure adequate partition sizes in partition table:
-```
-# Name,   Type, SubType, Offset,  Size, Flags
-nvs,      data, nvs,     0x9000,  0x5000,
-otadata,  data, ota,     0xe000,  0x2000,
-app0,     app,  ota_0,   0x10000, 0x140000,
-app1,     app,  ota_1,   0x150000,0x140000,
-spiffs,   data, spiffs,  0x290000,0x160000,
-```
-
-## Debugging Techniques
-
-### Serial Output Analysis
-
-Enable comprehensive debugging:
-```cpp
-mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION | SYNC | 
-                     COMMUNICATION | GENERAL | MSG_TYPES | REMOTE);
-```
-
-Look for patterns in the output:
-- Repeated connection attempts
-- Memory allocation failures
-- Message transmission errors
-- Time synchronization issues
-
-### Network Analysis
-
-Use WiFi monitoring tools:
-- WiFi Analyzer apps to check channel congestion
-- Router logs to see connection patterns
-- Packet capture tools for advanced debugging
-
-### Code Instrumentation
-
-Add timing measurements:
-```cpp
-void timedFunction() {
-    unsigned long start = millis();
-    
-    // Your code here
-    performOperation();
-    
-    unsigned long duration = millis() - start;
-    if (duration > 1000) {  // Alert if > 1 second
-        Serial.printf("Slow operation: %lu ms\n", duration);
-    }
-}
-```
-
-## Getting Help
-
-If you're still experiencing issues:
-
-1. **Check the [FAQ](faq.md)** for additional solutions
-2. **Search existing issues** on [GitHub](https://github.com/Alteriom/painlessMesh/issues)
-3. **Post in the community forum** with:
-   - Complete serial output with debug enabled
-   - Hardware details (ESP32/ESP8266 model)
-   - Network topology (number of nodes, layout)
-   - Code snippets showing the problem
-4. **Create a minimal test case** that reproduces the issue
-5. **Include library versions** and platform information
-
-## Prevention Best Practices
-
-- **Start simple** - Test with 2 nodes before scaling up
-- **Monitor resources** - Check memory and CPU usage regularly
-- **Use version control** - Track changes that might introduce issues
-- **Test incremental changes** - Don't change everything at once
-- **Document your setup** - Keep notes on working configurations
-- **Regular testing** - Verify mesh operation after any changes
-
+# Common Issues and Solutions
+
+This guide covers the most frequently encountered problems when working with painlessMesh and their solutions.
+
+## Connection Issues
+
+### Nodes Not Connecting
+
+**Symptoms:**
+- Nodes don't appear in each other's node lists
+- No "New Connection" messages in serial output
+- Mesh remains disconnected
+
+**Solutions:**
+
+#### 1. Check Network Credentials
+Ensure all nodes use identical network settings:
+
+```cpp
+// These MUST be identical on all nodes
+#define MESH_PREFIX     "MyMeshNetwork"    // Exact match required
+#define MESH_PASSWORD   "password123"      // Case sensitive
+#define MESH_PORT       5555               // Must match
+```
+
+#### 2. Verify WiFi Range
+- Nodes must be within WiFi range (typically 50-200m)
+- Check for interference from other 2.4GHz devices
+- Try moving nodes closer together for testing
+
+#### 3. Check Serial Output
+Enable connection debugging:
+
+```cpp
+mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION);
+```
+
+Look for error messages like:
+- "Failed to connect to mesh"
+- "Connection timeout"
+- "Authentication failed"
+
+#### 4. Reset Network Settings
+Clear stored WiFi credentials:
+
+```cpp
+void setup() {
+    // Add this before mesh.init()
+    WiFi.disconnect(true);  // Clear stored networks
+    delay(1000);
+    
+    mesh.init(MESH_PREFIX, MESH_PASSWORD, &userScheduler, MESH_PORT);
+}
+```
+
+### Frequent Disconnections
+
+**Symptoms:**
+- Nodes connect but disconnect shortly after
+- Repeated "Connection dropped" messages
+- Unstable mesh topology
+
+**Solutions:**
+
+#### 1. Check Power Supply
+- Ensure stable power supply (USB power can be insufficient)
+- Use adequate power adapters (≥1A for ESP32, ≥500mA for ESP8266)
+- Check for voltage drops during WiFi transmission
+
+#### 2. Reduce Connection Load
+Limit the number of simultaneous connections:
+
+```cpp
+// Reduce connection count on ESP8266
+#define MAX_CONN 2  // Instead of default 4
+```
+
+#### 3. Increase Connection Timeout
+```cpp
+// Extend connection timeouts
+#define CONNECTION_TIMEOUT 60000  // 60 seconds instead of 30
+```
+
+#### 4. Memory Issues
+Monitor memory usage:
+
+```cpp
+void checkMemory() {
+    Serial.printf("Free heap: %d bytes\n", ESP.getFreeHeap());
+    if (ESP.getFreeHeap() < 10000) {  // ESP32
+        Serial.println("WARNING: Low memory!");
+    }
+}
+```
+
+## Message Delivery Issues
+
+### Messages Not Being Received
+
+**Symptoms:**
+- `sendBroadcast()` returns `true` but messages don't arrive
+- Callbacks not triggered
+- Silent message failures
+
+**Solutions:**
+
+#### 1. Check Callback Registration
+Ensure callbacks are set before `mesh.init()`:
+
+```cpp
+void setup() {
+    Serial.begin(115200);
+    
+    // Set callbacks BEFORE init
+    mesh.onReceive(&receivedCallback);
+    mesh.onNewConnection(&newConnectionCallback);
+    
+    // Then initialize
+    mesh.init(MESH_PREFIX, MESH_PASSWORD, &userScheduler, MESH_PORT);
+}
+```
+
+#### 2. Verify Message Format
+Check JSON formatting for custom messages:
+
+```cpp
+void sendSensorData() {
+    // Proper JSON formatting
+    String msg = "{";
+    msg += "\"type\":\"sensor\",";
+    msg += "\"value\":" + String(sensorValue) + ",";
+    msg += "\"timestamp\":" + String(mesh.getNodeTime());
+    msg += "}";  // Don't forget closing brace
+    
+    mesh.sendBroadcast(msg);
+}
+```
+
+#### 3. Enable Communication Debugging
+```cpp
+mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION | COMMUNICATION);
+```
+
+#### 4. Check Network Congestion
+Reduce message frequency if network is congested:
+
+```cpp
+// Instead of every second
+Task taskSendMessage(10000, TASK_FOREVER, &sendMessage);  // Every 10 seconds
+```
+
+### Large Messages Being Dropped
+
+**Symptoms:**
+- Small messages work, large ones don't
+- Memory errors in serial output
+- Random message failures
+
+**Solutions:**
+
+#### 1. Reduce Message Size
+```cpp
+// Keep messages under 1KB for reliability
+String createMessage() {
+    String msg = "{\"data\":\"";
+    msg += shortData; // Keep data concise
+    msg += "\"}";
+    
+    if (msg.length() > 1000) {
+        Serial.println("Warning: Message too large");
+        return "{}"; // Send empty object
+    }
+    
+    return msg;
+}
+```
+
+#### 2. Split Large Data
+```cpp
+void sendLargeData(String largeData) {
+    const size_t chunkSize = 500;
+    
+    for (size_t i = 0; i < largeData.length(); i += chunkSize) {
+        String chunk = largeData.substring(i, i + chunkSize);
+        String msg = "{\"chunk\":" + String(i/chunkSize) + ",\"data\":\"" + chunk + "\"}";
+        mesh.sendBroadcast(msg);
+        delay(100); // Small delay between chunks
+    }
+}
+```
+
+## Memory Issues
+
+### ESP8266 Memory Limitations
+
+**Symptoms:**
+- Frequent crashes or resets
+- "Out of memory" errors
+- Unstable behavior under load
+
+**Solutions:**
+
+#### 1. Reduce Buffer Sizes
+```cpp
+// Use smaller JSON documents
+DynamicJsonDocument doc(512);  // Instead of 1024 or larger
+
+// Limit string sizes
+TSTRING deviceName;
+deviceName.reserve(32);  // Pre-allocate reasonable size
+```
+
+#### 2. Limit Concurrent Connections
+```cpp
+#define MAX_CONN 2  // ESP8266 works best with 2-3 connections
+```
+
+#### 3. Optimize Task Usage
+```cpp
+// Combine multiple tasks into one
+Task taskMultiFunction(30000, TASK_FOREVER, [](){
+    sendSensorData();
+    checkStatus();
+    cleanupMemory();
+});
+```
+
+#### 4. Implement Memory Monitoring
+```cpp
+void monitorMemory() {
+    uint32_t freeHeap = ESP.getFreeHeap();
+    Serial.printf("Free heap: %u bytes\n", freeHeap);
+    
+    if (freeHeap < 5000) {  // Critical threshold for ESP8266
+        Serial.println("CRITICAL: Very low memory!");
+        // Take corrective action
+        mesh.stop();
+        delay(1000);
+        ESP.restart();
+    }
+}
+```
+
+### ESP32 Memory Issues
+
+**Symptoms:**
+- Slower performance over time
+- Memory leaks
+- Task watchdog timeouts
+
+**Solutions:**
+
+#### 1. Monitor Heap Fragmentation
+```cpp
+void checkHeapHealth() {
+    Serial.printf("Free heap: %u bytes\n", ESP.getFreeHeap());
+    Serial.printf("Largest block: %u bytes\n", ESP.getMaxAllocHeap());
+    
+    // If largest block is much smaller than free heap, 
+    // heap is fragmented
+    if (ESP.getMaxAllocHeap() < ESP.getFreeHeap() / 2) {
+        Serial.println("Warning: Heap fragmentation detected");
+    }
+}
+```
+
+#### 2. Use Static Allocation When Possible
+```cpp
+// Instead of dynamic allocation
+StaticJsonDocument<1024> doc;  // Pre-allocated
+
+// Or use stack allocation for small objects
+char buffer[256];
+snprintf(buffer, sizeof(buffer), "{\"value\":%d}", value);
+```
+
+## Compilation Issues
+
+### Library Not Found
+
+**Symptoms:**
+- "painlessMesh.h: No such file or directory"
+- Library compilation errors
+
+**Solutions:**
+
+#### 1. Arduino IDE
+- Go to **Sketch → Include Library → Manage Libraries**
+- Search for "painlessMesh" and install latest version
+- Ensure ArduinoJson and TaskScheduler are also installed
+
+#### 2. PlatformIO
+Add to `platformio.ini`:
+```ini
+lib_deps = 
+    painlessMesh
+    bblanchon/ArduinoJson@^6.21.3
+    arkhipenko/TaskScheduler@^3.7.0
+```
+
+### Version Compatibility Issues
+
+**Symptoms:**
+- Compilation errors after library updates
+- API function not found errors
+- Deprecated warnings
+
+**Solutions:**
+
+#### 1. Check Version Compatibility
+```cpp
+// Check painlessMesh version
+#include "painlessMesh.h"
+Serial.printf("painlessMesh version: %s\n", PAINLESSMESH_VERSION);
+```
+
+#### 2. Lock Library Versions
+In `platformio.ini`:
+```ini
+lib_deps = 
+    painlessMesh@1.5.0        # Lock to specific version
+    bblanchon/ArduinoJson@6.21.3
+    arkhipenko/TaskScheduler@3.7.0
+```
+
+#### 3. Update Deprecated APIs
+```cpp
+// Old API (deprecated)
+mesh.onReceive(&receivedCallback);
+
+// New API (if changed in your version)
+mesh.onReceive([](uint32_t from, String& msg) {
+    receivedCallback(from, msg);
+});
+```
+
+## Performance Issues
+
+### Slow Message Delivery
+
+**Symptoms:**
+- Messages take several seconds to arrive
+- High latency in mesh communication
+- Sluggish response times
+
+**Solutions:**
+
+#### 1. Check Network Topology
+```cpp
+void printTopology() {
+    String topology = mesh.subConnectionJson(true);
+    Serial.println("Current topology:");
+    Serial.println(topology);
+    
+    // Look for long chains or star topologies
+    // Optimal: balanced tree with short paths
+}
+```
+
+#### 2. Reduce Message Frequency
+```cpp
+// Instead of high frequency
+Task taskFastSender(1000, TASK_FOREVER, &sendMessage);  // Every second
+
+// Use lower frequency
+Task taskSlowSender(10000, TASK_FOREVER, &sendMessage); // Every 10 seconds
+```
+
+#### 3. Optimize Message Size
+```cpp
+// Compact JSON formatting
+String createOptimizedMessage() {
+    // Use short field names
+    String msg = "{\"t\":" + String(temp) + ",\"h\":" + String(hum) + "}";
+    return msg;
+}
+```
+
+### High CPU Usage
+
+**Symptoms:**
+- ESP becomes hot during operation
+- Watchdog timer resets
+- Sluggish response to other tasks
+
+**Solutions:**
+
+#### 1. Add Delays in Tight Loops
+```cpp
+void loop() {
+    mesh.update();
+    
+    // Add small delay to prevent CPU overload
+    delay(10);
+    
+    // Or yield to other tasks
+    yield();
+}
+```
+
+#### 2. Reduce Debug Output
+```cpp
+// Only use essential debug messages in production
+mesh.setDebugMsgTypes(ERROR);  // Only errors
+```
+
+#### 3. Optimize Task Scheduling
+```cpp
+// Spread tasks over time
+Task task1(30000, TASK_FOREVER, &function1);     // Every 30s
+Task task2(35000, TASK_FOREVER, &function2);     // Every 35s (offset)
+Task task3(40000, TASK_FOREVER, &function3);     // Every 40s
+```
+
+## Platform-Specific Issues
+
+### ESP8266 Specific
+
+**Reset Loops:**
+```cpp
+// Increase watchdog timeout
+ESP.wdtDisable();
+// Perform long operations
+ESP.wdtEnable(5000);  // 5 second timeout
+```
+
+**Flash Memory Issues:**
+```cpp
+// Check flash size
+Serial.printf("Flash size: %u bytes\n", ESP.getFlashChipSize());
+
+// Ensure adequate space for SPIFFS/LittleFS
+// Reserve at least 64KB for filesystem
+```
+
+### ESP32 Specific
+
+**Core Affinity:**
+```cpp
+// Pin mesh tasks to specific core if needed
+void setup() {
+    // Use core 0 for mesh (core 1 for app)
+    xTaskCreatePinnedToCore(meshTask, "MeshTask", 8192, NULL, 1, NULL, 0);
+}
+```
+
+**Partition Scheme:**
+Ensure adequate partition sizes in partition table:
+```
+# Name,   Type, SubType, Offset,  Size, Flags
+nvs,      data, nvs,     0x9000,  0x5000,
+otadata,  data, ota,     0xe000,  0x2000,
+app0,     app,  ota_0,   0x10000, 0x140000,
+app1,     app,  ota_1,   0x150000,0x140000,
+spiffs,   data, spiffs,  0x290000,0x160000,
+```
+
+## Debugging Techniques
+
+### Serial Output Analysis
+
+Enable comprehensive debugging:
+```cpp
+mesh.setDebugMsgTypes(ERROR | STARTUP | CONNECTION | SYNC | 
+                     COMMUNICATION | GENERAL | MSG_TYPES | REMOTE);
+```
+
+Look for patterns in the output:
+- Repeated connection attempts
+- Memory allocation failures
+- Message transmission errors
+- Time synchronization issues
+
+### Network Analysis
+
+Use WiFi monitoring tools:
+- WiFi Analyzer apps to check channel congestion
+- Router logs to see connection patterns
+- Packet capture tools for advanced debugging
+
+### Code Instrumentation
+
+Add timing measurements:
+```cpp
+void timedFunction() {
+    unsigned long start = millis();
+    
+    // Your code here
+    performOperation();
+    
+    unsigned long duration = millis() - start;
+    if (duration > 1000) {  // Alert if > 1 second
+        Serial.printf("Slow operation: %lu ms\n", duration);
+    }
+}
+```
+
+## Getting Help
+
+If you're still experiencing issues:
+
+1. **Check the [FAQ](faq.md)** for additional solutions
+2. **Search existing issues** on [GitHub](https://github.com/Alteriom/painlessMesh/issues)
+3. **Post in the community forum** with:
+   - Complete serial output with debug enabled
+   - Hardware details (ESP32/ESP8266 model)
+   - Network topology (number of nodes, layout)
+   - Code snippets showing the problem
+4. **Create a minimal test case** that reproduces the issue
+5. **Include library versions** and platform information
+
+## Prevention Best Practices
+
+- **Start simple** - Test with 2 nodes before scaling up
+- **Monitor resources** - Check memory and CPU usage regularly
+- **Use version control** - Track changes that might introduce issues
+- **Test incremental changes** - Don't change everything at once
+- **Document your setup** - Keep notes on working configurations
+- **Regular testing** - Verify mesh operation after any changes
+
 Remember: Most mesh networking issues are related to network configuration, power supply, or memory management. Check these fundamentals first before diving into complex debugging.