esphome 2025.6.3__py3-none-any.whl → 2025.7.0b2__py3-none-any.whl

esphome/components/sx126x/sx126x.cpp

@@ -0,0 +1,523 @@
+#include "sx126x.h"
+#include "esphome/core/hal.h"
+#include "esphome/core/log.h"
+
+namespace esphome {
+namespace sx126x {
+
+static const char *const TAG = "sx126x";
+static const uint16_t RAMP[8] = {10, 20, 40, 80, 200, 800, 1700, 3400};
+static const uint32_t BW_HZ[31] = {4800,  5800,  7300,  9700,   11700,  14600,  19500,  23400,  29300,  39000,  46900,
+                                   58600, 78200, 93800, 117300, 156200, 187200, 234300, 312000, 373600, 467000, 7810,
+                                   10420, 15630, 20830, 31250,  41670,  62500,  125000, 250000, 500000};
+static const uint8_t BW_LORA[10] = {LORA_BW_7810,  LORA_BW_10420, LORA_BW_15630,  LORA_BW_20830,  LORA_BW_31250,
+                                    LORA_BW_41670, LORA_BW_62500, LORA_BW_125000, LORA_BW_250000, LORA_BW_500000};
+static const uint8_t BW_FSK[21] = {
+    FSK_BW_4800,   FSK_BW_5800,   FSK_BW_7300,   FSK_BW_9700,   FSK_BW_11700,  FSK_BW_14600,  FSK_BW_19500,
+    FSK_BW_23400,  FSK_BW_29300,  FSK_BW_39000,  FSK_BW_46900,  FSK_BW_58600,  FSK_BW_78200,  FSK_BW_93800,
+    FSK_BW_117300, FSK_BW_156200, FSK_BW_187200, FSK_BW_234300, FSK_BW_312000, FSK_BW_373600, FSK_BW_467000};
+
+static constexpr uint32_t RESET_DELAY_HIGH_US = 5000;
+static constexpr uint32_t RESET_DELAY_LOW_US = 2000;
+static constexpr uint32_t SWITCHING_DELAY_US = 1;
+static constexpr uint32_t TRANSMIT_TIMEOUT_MS = 4000;
+static constexpr uint32_t BUSY_TIMEOUT_MS = 20;
+
+// OCP (Over Current Protection) values
+static constexpr uint8_t OCP_80MA = 0x18;   // 80 mA max current
+static constexpr uint8_t OCP_140MA = 0x38;  // 140 mA max current
+
+// LoRa low data rate optimization threshold
+static constexpr float LOW_DATA_RATE_OPTIMIZE_THRESHOLD = 16.38f;  // 16.38 ms
+
+uint8_t SX126x::read_fifo_(uint8_t offset, std::vector<uint8_t> &packet) {
+  this->wait_busy_();
+  this->enable();
+  this->transfer_byte(RADIO_READ_BUFFER);
+  this->transfer_byte(offset);
+  uint8_t status = this->transfer_byte(0x00);
+  for (uint8_t &byte : packet) {
+    byte = this->transfer_byte(0x00);
+  }
+  this->disable();
+  return status;
+}
+
+void SX126x::write_fifo_(uint8_t offset, const std::vector<uint8_t> &packet) {
+  this->wait_busy_();
+  this->enable();
+  this->transfer_byte(RADIO_WRITE_BUFFER);
+  this->transfer_byte(offset);
+  for (const uint8_t &byte : packet) {
+    this->transfer_byte(byte);
+  }
+  this->disable();
+  delayMicroseconds(SWITCHING_DELAY_US);
+}
+
+uint8_t SX126x::read_opcode_(uint8_t opcode, uint8_t *data, uint8_t size) {
+  this->wait_busy_();
+  this->enable();
+  this->transfer_byte(opcode);
+  uint8_t status = this->transfer_byte(0x00);
+  for (int32_t i = 0; i < size; i++) {
+    data[i] = this->transfer_byte(0x00);
+  }
+  this->disable();
+  return status;
+}
+
+void SX126x::write_opcode_(uint8_t opcode, uint8_t *data, uint8_t size) {
+  this->wait_busy_();
+  this->enable();
+  this->transfer_byte(opcode);
+  for (int32_t i = 0; i < size; i++) {
+    this->transfer_byte(data[i]);
+  }
+  this->disable();
+  delayMicroseconds(SWITCHING_DELAY_US);
+}
+
+void SX126x::read_register_(uint16_t reg, uint8_t *data, uint8_t size) {
+  this->wait_busy_();
+  this->enable();
+  this->write_byte(RADIO_READ_REGISTER);
+  this->write_byte((reg >> 8) & 0xFF);
+  this->write_byte((reg >> 0) & 0xFF);
+  this->write_byte(0x00);
+  for (int32_t i = 0; i < size; i++) {
+    data[i] = this->transfer_byte(0x00);
+  }
+  this->disable();
+}
+
+void SX126x::write_register_(uint16_t reg, uint8_t *data, uint8_t size) {
+  this->wait_busy_();
+  this->enable();
+  this->write_byte(RADIO_WRITE_REGISTER);
+  this->write_byte((reg >> 8) & 0xFF);
+  this->write_byte((reg >> 0) & 0xFF);
+  for (int32_t i = 0; i < size; i++) {
+    this->transfer_byte(data[i]);
+  }
+  this->disable();
+  delayMicroseconds(SWITCHING_DELAY_US);
+}
+
+void SX126x::setup() {
+  ESP_LOGCONFIG(TAG, "Running setup");
+
+  // setup pins
+  this->busy_pin_->setup();
+  this->rst_pin_->setup();
+  this->dio1_pin_->setup();
+
+  // start spi
+  this->spi_setup();
+
+  // configure rf
+  this->configure();
+}
+
+void SX126x::configure() {
+  uint8_t buf[8];
+
+  // toggle chip reset
+  this->rst_pin_->digital_write(true);
+  delayMicroseconds(RESET_DELAY_HIGH_US);
+  this->rst_pin_->digital_write(false);
+  delayMicroseconds(RESET_DELAY_LOW_US);
+  this->rst_pin_->digital_write(true);
+  delayMicroseconds(RESET_DELAY_HIGH_US);
+
+  // wakeup
+  this->read_opcode_(RADIO_GET_STATUS, nullptr, 0);
+
+  // config tcxo
+  if (this->tcxo_voltage_ != TCXO_CTRL_NONE) {
+    uint32_t delay = this->tcxo_delay_ >> 6;
+    buf[0] = this->tcxo_voltage_;
+    buf[1] = (delay >> 16) & 0xFF;
+    buf[2] = (delay >> 8) & 0xFF;
+    buf[3] = (delay >> 0) & 0xFF;
+    this->write_opcode_(RADIO_SET_TCXOMODE, buf, 4);
+    buf[0] = 0x7F;
+    this->write_opcode_(RADIO_CALIBRATE, buf, 1);
+  }
+
+  // clear errors
+  buf[0] = 0x00;
+  buf[1] = 0x00;
+  this->write_opcode_(RADIO_CLR_ERROR, buf, 2);
+
+  // rf switch
+  if (this->rf_switch_) {
+    buf[0] = 0x01;
+    this->write_opcode_(RADIO_SET_RFSWITCHMODE, buf, 1);
+  }
+
+  // check silicon version to make sure hw is ok
+  this->read_register_(REG_VERSION_STRING, (uint8_t *) this->version_, 16);
+  if (strncmp(this->version_, "SX126", 5) != 0 && strncmp(this->version_, "LLCC68", 6) != 0) {
+    this->mark_failed();
+    return;
+  }
+
+  // setup packet type
+  buf[0] = this->modulation_;
+  this->write_opcode_(RADIO_SET_PACKETTYPE, buf, 1);
+
+  // calibrate image
+  this->run_image_cal();
+
+  // set frequency
+  uint64_t freq = ((uint64_t) this->frequency_ << 25) / XTAL_FREQ;
+  buf[0] = (uint8_t) ((freq >> 24) & 0xFF);
+  buf[1] = (uint8_t) ((freq >> 16) & 0xFF);
+  buf[2] = (uint8_t) ((freq >> 8) & 0xFF);
+  buf[3] = (uint8_t) (freq & 0xFF);
+  this->write_opcode_(RADIO_SET_RFFREQUENCY, buf, 4);
+
+  // configure pa
+  int8_t pa_power = this->pa_power_;
+  if (this->hw_version_ == "sx1261") {
+    // the following values were taken from section 13.1.14.1 table 13-21
+    // in rev 2.1 of the datasheet
+    if (pa_power == 15) {
+      uint8_t cfg[4] = {0x06, 0x00, 0x01, 0x01};
+      this->write_opcode_(RADIO_SET_PACONFIG, cfg, 4);
+    } else {
+      uint8_t cfg[4] = {0x04, 0x00, 0x01, 0x01};
+      this->write_opcode_(RADIO_SET_PACONFIG, cfg, 4);
+    }
+    pa_power = std::max(pa_power, (int8_t) -3);
+    pa_power = std::min(pa_power, (int8_t) 14);
+    buf[0] = OCP_80MA;
+    this->write_register_(REG_OCP, buf, 1);
+  } else {
+    // the following values were taken from section 13.1.14.1 table 13-21
+    // in rev 2.1 of the datasheet
+    uint8_t cfg[4] = {0x04, 0x07, 0x00, 0x01};
+    this->write_opcode_(RADIO_SET_PACONFIG, cfg, 4);
+    pa_power = std::max(pa_power, (int8_t) -3);
+    pa_power = std::min(pa_power, (int8_t) 22);
+    buf[0] = OCP_140MA;
+    this->write_register_(REG_OCP, buf, 1);
+  }
+  buf[0] = pa_power;
+  buf[1] = this->pa_ramp_;
+  this->write_opcode_(RADIO_SET_TXPARAMS, buf, 2);
+
+  // configure modem
+  if (this->modulation_ == PACKET_TYPE_LORA) {
+    // set modulation params
+    float duration = 1000.0f * std::pow(2, this->spreading_factor_) / BW_HZ[this->bandwidth_];
+    buf[0] = this->spreading_factor_;
+    buf[1] = BW_LORA[this->bandwidth_ - SX126X_BW_7810];
+    buf[2] = this->coding_rate_;
+    buf[3] = (duration > LOW_DATA_RATE_OPTIMIZE_THRESHOLD) ? 0x01 : 0x00;
+    this->write_opcode_(RADIO_SET_MODULATIONPARAMS, buf, 4);
+
+    // set packet params and sync word
+    this->set_packet_params_(this->payload_length_);
+    if (this->sync_value_.size() == 2) {
+      this->write_register_(REG_LORA_SYNCWORD, this->sync_value_.data(), this->sync_value_.size());
+    }
+  } else {
+    // set modulation params
+    uint32_t bitrate = ((uint64_t) XTAL_FREQ * 32) / this->bitrate_;
+    uint32_t fdev = ((uint64_t) this->deviation_ << 25) / XTAL_FREQ;
+    buf[0] = (bitrate >> 16) & 0xFF;
+    buf[1] = (bitrate >> 8) & 0xFF;
+    buf[2] = (bitrate >> 0) & 0xFF;
+    buf[3] = this->shaping_;
+    buf[4] = BW_FSK[this->bandwidth_ - SX126X_BW_4800];
+    buf[5] = (fdev >> 16) & 0xFF;
+    buf[6] = (fdev >> 8) & 0xFF;
+    buf[7] = (fdev >> 0) & 0xFF;
+    this->write_opcode_(RADIO_SET_MODULATIONPARAMS, buf, 8);
+
+    // set packet params and sync word
+    this->set_packet_params_(this->payload_length_);
+    if (!this->sync_value_.empty()) {
+      this->write_register_(REG_GFSK_SYNCWORD, this->sync_value_.data(), this->sync_value_.size());
+    }
+  }
+
+  // switch to rx or sleep
+  if (this->rx_start_) {
+    this->set_mode_rx();
+  } else {
+    this->set_mode_sleep();
+  }
+}
+
+size_t SX126x::get_max_packet_size() {
+  if (this->payload_length_ > 0) {
+    return this->payload_length_;
+  }
+  return 255;
+}
+
+void SX126x::set_packet_params_(uint8_t payload_length) {
+  uint8_t buf[9];
+  if (this->modulation_ == PACKET_TYPE_LORA) {
+    buf[0] = (this->preamble_size_ >> 8) & 0xFF;
+    buf[1] = (this->preamble_size_ >> 0) & 0xFF;
+    buf[2] = (this->payload_length_ > 0) ? 0x01 : 0x00;
+    buf[3] = payload_length;
+    buf[4] = (this->crc_enable_) ? 0x01 : 0x00;
+    buf[5] = 0x00;
+    this->write_opcode_(RADIO_SET_PACKETPARAMS, buf, 6);
+  } else {
+    uint16_t preamble_size = this->preamble_size_ * 8;
+    buf[0] = (preamble_size >> 8) & 0xFF;
+    buf[1] = (preamble_size >> 0) & 0xFF;
+    buf[2] = (this->preamble_detect_ > 0) ? ((this->preamble_detect_ - 1) | 0x04) : 0x00;
+    buf[3] = this->sync_value_.size() * 8;
+    buf[4] = 0x00;
+    buf[5] = 0x00;
+    buf[6] = payload_length;
+    buf[7] = this->crc_enable_ ? 0x06 : 0x01;
+    buf[8] = 0x00;
+    this->write_opcode_(RADIO_SET_PACKETPARAMS, buf, 9);
+  }
+}
+
+SX126xError SX126x::transmit_packet(const std::vector<uint8_t> &packet) {
+  if (this->payload_length_ > 0 && this->payload_length_ != packet.size()) {
+    ESP_LOGE(TAG, "Packet size does not match config");
+    return SX126xError::INVALID_PARAMS;
+  }
+  if (packet.empty() || packet.size() > this->get_max_packet_size()) {
+    ESP_LOGE(TAG, "Packet size out of range");
+    return SX126xError::INVALID_PARAMS;
+  }
+
+  SX126xError ret = SX126xError::NONE;
+  this->set_mode_standby(STDBY_XOSC);
+  if (this->payload_length_ == 0) {
+    this->set_packet_params_(packet.size());
+  }
+  this->write_fifo_(0x00, packet);
+  this->set_mode_tx();
+
+  // wait until transmit completes, typically the delay will be less than 100 ms
+  uint32_t start = millis();
+  while (!this->dio1_pin_->digital_read()) {
+    if (millis() - start > TRANSMIT_TIMEOUT_MS) {
+      ESP_LOGE(TAG, "Transmit packet failure");
+      ret = SX126xError::TIMEOUT;
+      break;
+    }
+  }
+
+  uint8_t buf[2];
+  buf[0] = 0xFF;
+  buf[1] = 0xFF;
+  this->write_opcode_(RADIO_CLR_IRQSTATUS, buf, 2);
+  if (this->rx_start_) {
+    this->set_mode_rx();
+  } else {
+    this->set_mode_sleep();
+  }
+  return ret;
+}
+
+void SX126x::call_listeners_(const std::vector<uint8_t> &packet, float rssi, float snr) {
+  for (auto &listener : this->listeners_) {
+    listener->on_packet(packet, rssi, snr);
+  }
+  this->packet_trigger_->trigger(packet, rssi, snr);
+}
+
+void SX126x::loop() {
+  if (!this->dio1_pin_->digital_read()) {
+    return;
+  }
+
+  uint16_t status;
+  uint8_t buf[3];
+  uint8_t rssi;
+  int8_t snr;
+  this->read_opcode_(RADIO_GET_IRQSTATUS, buf, 2);
+  this->write_opcode_(RADIO_CLR_IRQSTATUS, buf, 2);
+  status = (buf[0] << 8) | buf[1];
+  if ((status & IRQ_RX_DONE) == IRQ_RX_DONE) {
+    if ((status & IRQ_CRC_ERROR) != IRQ_CRC_ERROR) {
+      this->read_opcode_(RADIO_GET_PACKETSTATUS, buf, 3);
+      if (this->modulation_ == PACKET_TYPE_LORA) {
+        rssi = buf[0];
+        snr = buf[1];
+      } else {
+        rssi = buf[2];
+        snr = 0;
+      }
+      this->read_opcode_(RADIO_GET_RXBUFFERSTATUS, buf, 2);
+      this->packet_.resize(buf[0]);
+      this->read_fifo_(buf[1], this->packet_);
+      this->call_listeners_(this->packet_, (float) rssi / -2.0f, (float) snr / 4.0f);
+    }
+  }
+}
+
+void SX126x::run_image_cal() {
+  // the following values were taken from section 9.2.1 table 9-2
+  // in rev 2.1 of the datasheet
+  uint8_t buf[2] = {0, 0};
+  if (this->frequency_ > 900000000) {
+    buf[0] = 0xE1;
+    buf[1] = 0xE9;
+  } else if (this->frequency_ > 850000000) {
+    buf[0] = 0xD7;
+    buf[1] = 0xD8;
+  } else if (this->frequency_ > 770000000) {
+    buf[0] = 0xC1;
+    buf[1] = 0xC5;
+  } else if (this->frequency_ > 460000000) {
+    buf[0] = 0x75;
+    buf[1] = 0x81;
+  } else if (this->frequency_ > 425000000) {
+    buf[0] = 0x6B;
+    buf[1] = 0x6F;
+  }
+  if (buf[0] > 0 && buf[1] > 0) {
+    this->write_opcode_(RADIO_CALIBRATEIMAGE, buf, 2);
+  }
+}
+
+void SX126x::set_mode_rx() {
+  uint8_t buf[8];
+
+  // configure irq params
+  uint16_t irq = IRQ_RX_DONE | IRQ_RX_TX_TIMEOUT | IRQ_CRC_ERROR;
+  buf[0] = (irq >> 8) & 0xFF;
+  buf[1] = (irq >> 0) & 0xFF;
+  buf[2] = (irq >> 8) & 0xFF;
+  buf[3] = (irq >> 0) & 0xFF;
+  buf[4] = (IRQ_RADIO_NONE >> 8) & 0xFF;
+  buf[5] = (IRQ_RADIO_NONE >> 0) & 0xFF;
+  buf[6] = (IRQ_RADIO_NONE >> 8) & 0xFF;
+  buf[7] = (IRQ_RADIO_NONE >> 0) & 0xFF;
+  this->write_opcode_(RADIO_SET_DIOIRQPARAMS, buf, 8);
+
+  // set timeout to 0
+  buf[0] = 0x00;
+  this->write_opcode_(RADIO_SET_LORASYMBTIMEOUT, buf, 1);
+
+  // switch to continuous mode rx
+  buf[0] = 0xFF;
+  buf[1] = 0xFF;
+  buf[2] = 0xFF;
+  this->write_opcode_(RADIO_SET_RX, buf, 3);
+}
+
+void SX126x::set_mode_tx() {
+  uint8_t buf[8];
+
+  // configure irq params
+  uint16_t irq = IRQ_TX_DONE | IRQ_RX_TX_TIMEOUT;
+  buf[0] = (irq >> 8) & 0xFF;
+  buf[1] = (irq >> 0) & 0xFF;
+  buf[2] = (irq >> 8) & 0xFF;
+  buf[3] = (irq >> 0) & 0xFF;
+  buf[4] = (IRQ_RADIO_NONE >> 8) & 0xFF;
+  buf[5] = (IRQ_RADIO_NONE >> 0) & 0xFF;
+  buf[6] = (IRQ_RADIO_NONE >> 8) & 0xFF;
+  buf[7] = (IRQ_RADIO_NONE >> 0) & 0xFF;
+  this->write_opcode_(RADIO_SET_DIOIRQPARAMS, buf, 8);
+
+  // switch to single mode tx
+  buf[0] = 0x00;
+  buf[1] = 0x00;
+  buf[2] = 0x00;
+  this->write_opcode_(RADIO_SET_TX, buf, 3);
+}
+
+void SX126x::set_mode_sleep() {
+  uint8_t buf[1];
+  buf[0] = 0x05;
+  this->write_opcode_(RADIO_SET_SLEEP, buf, 1);
+}
+
+void SX126x::set_mode_standby(SX126xStandbyMode mode) {
+  uint8_t buf[1];
+  buf[0] = mode;
+  this->write_opcode_(RADIO_SET_STANDBY, buf, 1);
+}
+
+void SX126x::wait_busy_() {
+  // wait if the device is busy, the maximum delay is only be a few ms
+  // with most commands taking only a few us
+  uint32_t start = millis();
+  while (this->busy_pin_->digital_read()) {
+    if (millis() - start > BUSY_TIMEOUT_MS) {
+      ESP_LOGE(TAG, "Wait busy timeout");
+      this->mark_failed();
+      break;
+    }
+  }
+}
+
+void SX126x::dump_config() {
+  ESP_LOGCONFIG(TAG, "SX126x:");
+  LOG_PIN("  CS Pin: ", this->cs_);
+  LOG_PIN("  BUSY Pin: ", this->busy_pin_);
+  LOG_PIN("  RST Pin: ", this->rst_pin_);
+  LOG_PIN("  DIO1 Pin: ", this->dio1_pin_);
+  ESP_LOGCONFIG(TAG,
+                "  HW Version: %15s\n"
+                "  Frequency: %" PRIu32 " Hz\n"
+                "  Bandwidth: %" PRIu32 " Hz\n"
+                "  PA Power: %" PRId8 " dBm\n"
+                "  PA Ramp: %" PRIu16 " us\n"
+                "  Payload Length: %" PRIu32 "\n"
+                "  CRC Enable: %s\n"
+                "  Rx Start: %s",
+                this->version_, this->frequency_, BW_HZ[this->bandwidth_], this->pa_power_, RAMP[this->pa_ramp_],
+                this->payload_length_, TRUEFALSE(this->crc_enable_), TRUEFALSE(this->rx_start_));
+  if (this->modulation_ == PACKET_TYPE_GFSK) {
+    const char *shaping = "NONE";
+    if (this->shaping_ == GAUSSIAN_BT_0_3) {
+      shaping = "GAUSSIAN_BT_0_3";
+    } else if (this->shaping_ == GAUSSIAN_BT_0_5) {
+      shaping = "GAUSSIAN_BT_0_5";
+    } else if (this->shaping_ == GAUSSIAN_BT_0_7) {
+      shaping = "GAUSSIAN_BT_0_7";
+    } else if (this->shaping_ == GAUSSIAN_BT_1_0) {
+      shaping = "GAUSSIAN_BT_1_0";
+    }
+    ESP_LOGCONFIG(TAG,
+                  "  Modulation: FSK\n"
+                  "  Deviation: %" PRIu32 " Hz\n"
+                  "  Shaping: %s\n"
+                  "  Preamble Size: %" PRIu16 "\n"
+                  "  Preamble Detect: %" PRIu16 "\n"
+                  "  Bitrate: %" PRIu32 "b/s",
+                  this->deviation_, shaping, this->preamble_size_, this->preamble_detect_, this->bitrate_);
+  } else if (this->modulation_ == PACKET_TYPE_LORA) {
+    const char *cr = "4/8";
+    if (this->coding_rate_ == LORA_CR_4_5) {
+      cr = "4/5";
+    } else if (this->coding_rate_ == LORA_CR_4_6) {
+      cr = "4/6";
+    } else if (this->coding_rate_ == LORA_CR_4_7) {
+      cr = "4/7";
+    }
+    ESP_LOGCONFIG(TAG,
+                  "  Modulation: LORA\n"
+                  "  Spreading Factor: %" PRIu8 "\n"
+                  "  Coding Rate: %s\n"
+                  "  Preamble Size: %" PRIu16,
+                  this->spreading_factor_, cr, this->preamble_size_);
+  }
+  if (!this->sync_value_.empty()) {
+    ESP_LOGCONFIG(TAG, "  Sync Value: 0x%s", format_hex(this->sync_value_).c_str());
+  }
+  if (this->is_failed()) {
+    ESP_LOGE(TAG, "Configuring SX126x failed");
+  }
+}
+
+}  // namespace sx126x
+}  // namespace esphome

esphome/components/sx126x/sx126x.h

@@ -0,0 +1,140 @@
+#pragma once
+
+#include "esphome/components/spi/spi.h"
+#include "esphome/core/automation.h"
+#include "esphome/core/component.h"
+#include "sx126x_reg.h"
+#include <utility>
+#include <vector>
+
+namespace esphome {
+namespace sx126x {
+
+enum SX126xBw : uint8_t {
+  // FSK
+  SX126X_BW_4800,
+  SX126X_BW_5800,
+  SX126X_BW_7300,
+  SX126X_BW_9700,
+  SX126X_BW_11700,
+  SX126X_BW_14600,
+  SX126X_BW_19500,
+  SX126X_BW_23400,
+  SX126X_BW_29300,
+  SX126X_BW_39000,
+  SX126X_BW_46900,
+  SX126X_BW_58600,
+  SX126X_BW_78200,
+  SX126X_BW_93800,
+  SX126X_BW_117300,
+  SX126X_BW_156200,
+  SX126X_BW_187200,
+  SX126X_BW_234300,
+  SX126X_BW_312000,
+  SX126X_BW_373600,
+  SX126X_BW_467000,
+  // LORA
+  SX126X_BW_7810,
+  SX126X_BW_10420,
+  SX126X_BW_15630,
+  SX126X_BW_20830,
+  SX126X_BW_31250,
+  SX126X_BW_41670,
+  SX126X_BW_62500,
+  SX126X_BW_125000,
+  SX126X_BW_250000,
+  SX126X_BW_500000,
+};
+
+enum class SX126xError { NONE = 0, TIMEOUT, INVALID_PARAMS };
+
+class SX126xListener {
+ public:
+  virtual void on_packet(const std::vector<uint8_t> &packet, float rssi, float snr) = 0;
+};
+
+class SX126x : public Component,
+               public spi::SPIDevice<spi::BIT_ORDER_MSB_FIRST, spi::CLOCK_POLARITY_LOW, spi::CLOCK_PHASE_LEADING,
+                                     spi::DATA_RATE_8MHZ> {
+ public:
+  size_t get_max_packet_size();
+  float get_setup_priority() const override { return setup_priority::PROCESSOR; }
+  void setup() override;
+  void loop() override;
+  void dump_config() override;
+  void set_bandwidth(SX126xBw bandwidth) { this->bandwidth_ = bandwidth; }
+  void set_bitrate(uint32_t bitrate) { this->bitrate_ = bitrate; }
+  void set_busy_pin(InternalGPIOPin *busy_pin) { this->busy_pin_ = busy_pin; }
+  void set_coding_rate(uint8_t coding_rate) { this->coding_rate_ = coding_rate; }
+  void set_crc_enable(bool crc_enable) { this->crc_enable_ = crc_enable; }
+  void set_deviation(uint32_t deviation) { this->deviation_ = deviation; }
+  void set_dio1_pin(InternalGPIOPin *dio1_pin) { this->dio1_pin_ = dio1_pin; }
+  void set_frequency(uint32_t frequency) { this->frequency_ = frequency; }
+  void set_hw_version(const std::string &hw_version) { this->hw_version_ = hw_version; }
+  void set_mode_rx();
+  void set_mode_tx();
+  void set_mode_standby(SX126xStandbyMode mode);
+  void set_mode_sleep();
+  void set_modulation(uint8_t modulation) { this->modulation_ = modulation; }
+  void set_pa_power(int8_t power) { this->pa_power_ = power; }
+  void set_pa_ramp(uint8_t ramp) { this->pa_ramp_ = ramp; }
+  void set_payload_length(uint8_t payload_length) { this->payload_length_ = payload_length; }
+  void set_preamble_detect(uint16_t preamble_detect) { this->preamble_detect_ = preamble_detect; }
+  void set_preamble_size(uint16_t preamble_size) { this->preamble_size_ = preamble_size; }
+  void set_rst_pin(InternalGPIOPin *rst_pin) { this->rst_pin_ = rst_pin; }
+  void set_rx_start(bool rx_start) { this->rx_start_ = rx_start; }
+  void set_rf_switch(bool rf_switch) { this->rf_switch_ = rf_switch; }
+  void set_shaping(uint8_t shaping) { this->shaping_ = shaping; }
+  void set_spreading_factor(uint8_t spreading_factor) { this->spreading_factor_ = spreading_factor; }
+  void set_sync_value(const std::vector<uint8_t> &sync_value) { this->sync_value_ = sync_value; }
+  void set_tcxo_voltage(uint8_t tcxo_voltage) { this->tcxo_voltage_ = tcxo_voltage; }
+  void set_tcxo_delay(uint32_t tcxo_delay) { this->tcxo_delay_ = tcxo_delay; }
+  void run_image_cal();
+  void configure();
+  SX126xError transmit_packet(const std::vector<uint8_t> &packet);
+  void register_listener(SX126xListener *listener) { this->listeners_.push_back(listener); }
+  Trigger<std::vector<uint8_t>, float, float> *get_packet_trigger() const { return this->packet_trigger_; };
+
+ protected:
+  void configure_fsk_ook_();
+  void configure_lora_();
+  void set_packet_params_(uint8_t payload_length);
+  uint8_t read_fifo_(uint8_t offset, std::vector<uint8_t> &packet);
+  void write_fifo_(uint8_t offset, const std::vector<uint8_t> &packet);
+  void write_opcode_(uint8_t opcode, uint8_t *data, uint8_t size);
+  uint8_t read_opcode_(uint8_t opcode, uint8_t *data, uint8_t size);
+  void write_register_(uint16_t reg, uint8_t *data, uint8_t size);
+  void read_register_(uint16_t reg, uint8_t *data, uint8_t size);
+  void call_listeners_(const std::vector<uint8_t> &packet, float rssi, float snr);
+  void wait_busy_();
+  Trigger<std::vector<uint8_t>, float, float> *packet_trigger_{new Trigger<std::vector<uint8_t>, float, float>()};
+  std::vector<SX126xListener *> listeners_;
+  std::vector<uint8_t> packet_;
+  std::vector<uint8_t> sync_value_;
+  InternalGPIOPin *busy_pin_{nullptr};
+  InternalGPIOPin *dio1_pin_{nullptr};
+  InternalGPIOPin *rst_pin_{nullptr};
+  std::string hw_version_;
+  char version_[16];
+  SX126xBw bandwidth_{SX126X_BW_125000};
+  uint32_t bitrate_{0};
+  uint32_t deviation_{0};
+  uint32_t frequency_{0};
+  uint32_t payload_length_{0};
+  uint32_t tcxo_delay_{0};
+  uint16_t preamble_detect_{0};
+  uint16_t preamble_size_{0};
+  uint8_t tcxo_voltage_{0};
+  uint8_t coding_rate_{0};
+  uint8_t modulation_{PACKET_TYPE_LORA};
+  uint8_t pa_ramp_{0};
+  uint8_t shaping_{0};
+  uint8_t spreading_factor_{0};
+  int8_t pa_power_{0};
+  bool crc_enable_{false};
+  bool rx_start_{false};
+  bool rf_switch_{false};
+};
+
+}  // namespace sx126x
+}  // namespace esphome