libwz 0.1.0

package/deps/zlib/zlib.h

@@ -0,0 +1,2057 @@
+/* zlib.h -- interface of the 'zlib' general purpose compression library
+  version 1.3.2, February 17th, 2026
+
+  Copyright (C) 1995-2026 Jean-loup Gailly and Mark Adler
+
+  This software is provided 'as-is', without any express or implied
+  warranty.  In no event will the authors be held liable for any damages
+  arising from the use of this software.
+
+  Permission is granted to anyone to use this software for any purpose,
+  including commercial applications, and to alter it and redistribute it
+  freely, subject to the following restrictions:
+
+  1. The origin of this software must not be misrepresented; you must not
+     claim that you wrote the original software. If you use this software
+     in a product, an acknowledgment in the product documentation would be
+     appreciated but is not required.
+  2. Altered source versions must be plainly marked as such, and must not be
+     misrepresented as being the original software.
+  3. This notice may not be removed or altered from any source distribution.
+
+  Jean-loup Gailly        Mark Adler
+  jloup@gzip.org          madler@alumni.caltech.edu
+
+
+  The data format used by the zlib library is described by RFCs (Request for
+  Comments) 1950 to 1952 at https://datatracker.ietf.org/doc/html/rfc1950
+  (zlib format), rfc1951 (deflate format) and rfc1952 (gzip format).
+*/
+
+#ifndef ZLIB_H
+#define ZLIB_H
+
+#ifdef ZLIB_BUILD
+#  include <zconf.h>
+#else
+# include "zconf.h"
+#endif
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#define ZLIB_VERSION "1.3.2"
+#define ZLIB_VERNUM 0x1320
+#define ZLIB_VER_MAJOR 1
+#define ZLIB_VER_MINOR 3
+#define ZLIB_VER_REVISION 2
+#define ZLIB_VER_SUBREVISION 0
+
+/*
+    The 'zlib' compression library provides in-memory compression and
+  decompression functions, including integrity checks of the uncompressed data.
+  This version of the library supports only one compression method (deflation)
+  but other algorithms will be added later and will have the same stream
+  interface.
+
+    Compression can be done in a single step if the buffers are large enough,
+  or can be done by repeated calls of the compression function.  In the latter
+  case, the application must provide more input and/or consume the output
+  (providing more output space) before each call.
+
+    The compressed data format used by default by the in-memory functions is
+  the zlib format, which is a zlib wrapper documented in RFC 1950, wrapped
+  around a deflate stream, which is itself documented in RFC 1951.
+
+    The library also supports reading and writing files in gzip (.gz) format
+  with an interface similar to that of stdio using the functions that start
+  with "gz".  The gzip format is different from the zlib format.  gzip is a
+  gzip wrapper, documented in RFC 1952, wrapped around a deflate stream.
+
+    This library can optionally read and write gzip and raw deflate streams in
+  memory as well.
+
+    The zlib format was designed to be compact and fast for use in memory
+  and on communications channels.  The gzip format was designed for single-
+  file compression on file systems, has a larger header than zlib to maintain
+  directory information, and uses a different, slower check method than zlib.
+
+    The library does not install any signal handler.  The decoder checks
+  the consistency of the compressed data, so the library should never crash
+  even in the case of corrupted input.
+*/
+
+typedef voidpf (*alloc_func)(voidpf opaque, uInt items, uInt size);
+typedef void   (*free_func)(voidpf opaque, voidpf address);
+
+struct internal_state;
+
+typedef struct z_stream_s {
+    z_const Bytef *next_in;     /* next input byte */
+    uInt     avail_in;  /* number of bytes available at next_in */
+    uLong    total_in;  /* total number of input bytes read so far */
+
+    Bytef    *next_out; /* next output byte will go here */
+    uInt     avail_out; /* remaining free space at next_out */
+    uLong    total_out; /* total number of bytes output so far */
+
+    z_const char *msg;  /* last error message, NULL if no error */
+    struct internal_state FAR *state; /* not visible by applications */
+
+    alloc_func zalloc;  /* used to allocate the internal state */
+    free_func  zfree;   /* used to free the internal state */
+    voidpf     opaque;  /* private data object passed to zalloc and zfree */
+
+    int     data_type;  /* best guess about the data type: binary or text
+                           for deflate, or the decoding state for inflate */
+    uLong   adler;      /* Adler-32 or CRC-32 value of the uncompressed data */
+    uLong   reserved;   /* reserved for future use */
+} z_stream;
+
+typedef z_stream FAR *z_streamp;
+
+/*
+     gzip header information passed to and from zlib routines.  See RFC 1952
+  for more details on the meanings of these fields.
+*/
+typedef struct gz_header_s {
+    int     text;       /* true if compressed data believed to be text */
+    uLong   time;       /* modification time */
+    int     xflags;     /* extra flags (not used when writing a gzip file) */
+    int     os;         /* operating system */
+    Bytef   *extra;     /* pointer to extra field or Z_NULL if none */
+    uInt    extra_len;  /* extra field length (valid if extra != Z_NULL) */
+    uInt    extra_max;  /* space at extra (only when reading header) */
+    Bytef   *name;      /* pointer to zero-terminated file name or Z_NULL */
+    uInt    name_max;   /* space at name (only when reading header) */
+    Bytef   *comment;   /* pointer to zero-terminated comment or Z_NULL */
+    uInt    comm_max;   /* space at comment (only when reading header) */
+    int     hcrc;       /* true if there was or will be a header crc */
+    int     done;       /* true when done reading gzip header (not used
+                           when writing a gzip file) */
+} gz_header;
+
+typedef gz_header FAR *gz_headerp;
+
+/*
+     The application must update next_in and avail_in when avail_in has dropped
+   to zero.  It must update next_out and avail_out when avail_out has dropped
+   to zero.  The application must initialize zalloc, zfree and opaque before
+   calling the init function.  All other fields are set by the compression
+   library and must not be updated by the application.
+
+     The opaque value provided by the application will be passed as the first
+   parameter for calls of zalloc and zfree.  This can be useful for custom
+   memory management.  The compression library attaches no meaning to the
+   opaque value.
+
+     zalloc must return Z_NULL if there is not enough memory for the object.
+   If zlib is used in a multi-threaded application, zalloc and zfree must be
+   thread safe.  In that case, zlib is thread-safe.  When zalloc and zfree are
+   Z_NULL on entry to the initialization function, they are set to internal
+   routines that use the standard library functions malloc() and free().
+
+     On 16-bit systems, the functions zalloc and zfree must be able to allocate
+   exactly 65536 bytes, but will not be required to allocate more than this if
+   the symbol MAXSEG_64K is defined (see zconf.h).  WARNING: On MSDOS, pointers
+   returned by zalloc for objects of exactly 65536 bytes *must* have their
+   offset normalized to zero.  The default allocation function provided by this
+   library ensures this (see zutil.c).  To reduce memory requirements and avoid
+   any allocation of 64K objects, at the expense of compression ratio, compile
+   the library with -DMAX_WBITS=14 (see zconf.h).
+
+     The fields total_in and total_out can be used for statistics or progress
+   reports.  After compression, total_in holds the total size of the
+   uncompressed data and may be saved for use by the decompressor (particularly
+   if the decompressor wants to decompress everything in a single step).
+*/
+
+                        /* constants */
+
+#define Z_NO_FLUSH      0
+#define Z_PARTIAL_FLUSH 1
+#define Z_SYNC_FLUSH    2
+#define Z_FULL_FLUSH    3
+#define Z_FINISH        4
+#define Z_BLOCK         5
+#define Z_TREES         6
+/* Allowed flush values; see deflate() and inflate() below for details */
+
+#define Z_OK            0
+#define Z_STREAM_END    1
+#define Z_NEED_DICT     2
+#define Z_ERRNO        (-1)
+#define Z_STREAM_ERROR (-2)
+#define Z_DATA_ERROR   (-3)
+#define Z_MEM_ERROR    (-4)
+#define Z_BUF_ERROR    (-5)
+#define Z_VERSION_ERROR (-6)
+/* Return codes for the compression/decompression functions. Negative values
+ * are errors, positive values are used for special but normal events.
+ */
+
+#define Z_NO_COMPRESSION         0
+#define Z_BEST_SPEED             1
+#define Z_BEST_COMPRESSION       9
+#define Z_DEFAULT_COMPRESSION  (-1)
+/* compression levels */
+
+#define Z_FILTERED            1
+#define Z_HUFFMAN_ONLY        2
+#define Z_RLE                 3
+#define Z_FIXED               4
+#define Z_DEFAULT_STRATEGY    0
+/* compression strategy; see deflateInit2() below for details */
+
+#define Z_BINARY   0
+#define Z_TEXT     1
+#define Z_ASCII    Z_TEXT   /* for compatibility with 1.2.2 and earlier */
+#define Z_UNKNOWN  2
+/* Possible values of the data_type field for deflate() */
+
+#define Z_DEFLATED   8
+/* The deflate compression method (the only one supported in this version) */
+
+#define Z_NULL  0  /* for initializing zalloc, zfree, opaque */
+
+#define zlib_version zlibVersion()
+/* for compatibility with versions < 1.0.2 */
+
+
+                        /* basic functions */
+
+ZEXTERN const char * ZEXPORT zlibVersion(void);
+/* The application can compare zlibVersion and ZLIB_VERSION for consistency.
+   If the first character differs, the library code actually used is not
+   compatible with the zlib.h header file used by the application.  This check
+   is automatically made by deflateInit and inflateInit.
+ */
+
+/*
+ZEXTERN int ZEXPORT deflateInit(z_streamp strm, int level);
+
+     Initializes the internal stream state for compression.  The fields
+   zalloc, zfree and opaque must be initialized before by the caller.  If
+   zalloc and zfree are set to Z_NULL, deflateInit updates them to use default
+   allocation functions.  total_in, total_out, adler, and msg are initialized.
+
+     The compression level must be Z_DEFAULT_COMPRESSION, or between 0 and 9:
+   1 gives best speed, 9 gives best compression, 0 gives no compression at all
+   (the input data is simply copied a block at a time).  Z_DEFAULT_COMPRESSION
+   requests a default compromise between speed and compression (currently
+   equivalent to level 6).
+
+     deflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_STREAM_ERROR if level is not a valid compression level, or
+   Z_VERSION_ERROR if the zlib library version (zlib_version) is incompatible
+   with the version assumed by the caller (ZLIB_VERSION).  msg is set to null
+   if there is no error message.  deflateInit does not perform any compression:
+   this will be done by deflate().
+*/
+
+
+ZEXTERN int ZEXPORT deflate(z_streamp strm, int flush);
+/*
+    deflate compresses as much data as possible, and stops when the input
+  buffer becomes empty or the output buffer becomes full.  It may introduce
+  some output latency (reading input without producing any output) except when
+  forced to flush.
+
+    The detailed semantics are as follows.  deflate performs one or both of the
+  following actions:
+
+  - Compress more input starting at next_in and update next_in and avail_in
+    accordingly.  If not all input can be processed (because there is not
+    enough room in the output buffer), next_in and avail_in are updated and
+    processing will resume at this point for the next call of deflate().
+
+  - Generate more output starting at next_out and update next_out and avail_out
+    accordingly.  This action is forced if the parameter flush is non zero.
+    Forcing flush frequently degrades the compression ratio, so this parameter
+    should be set only when necessary.  Some output may be provided even if
+    flush is zero.
+
+    Before the call of deflate(), the application should ensure that at least
+  one of the actions is possible, by providing more input and/or consuming more
+  output, and updating avail_in or avail_out accordingly; avail_out should
+  never be zero before the call.  The application can consume the compressed
+  output when it wants, for example when the output buffer is full (avail_out
+  == 0), or after each call of deflate().  If deflate returns Z_OK and with
+  zero avail_out, it must be called again after making room in the output
+  buffer because there might be more output pending. See deflatePending(),
+  which can be used if desired to determine whether or not there is more output
+  in that case.
+
+    Normally the parameter flush is set to Z_NO_FLUSH, which allows deflate to
+  decide how much data to accumulate before producing output, in order to
+  maximize compression.
+
+    If the parameter flush is set to Z_SYNC_FLUSH, all pending output is
+  flushed to the output buffer and the output is aligned on a byte boundary, so
+  that the decompressor can get all input data available so far.  (In
+  particular avail_in is zero after the call if enough output space has been
+  provided before the call.) Flushing may degrade compression for some
+  compression algorithms and so it should be used only when necessary.  This
+  completes the current deflate block and follows it with an empty stored block
+  that is three bits plus filler bits to the next byte, followed by four bytes
+  (00 00 ff ff).
+
+    If flush is set to Z_PARTIAL_FLUSH, all pending output is flushed to the
+  output buffer, but the output is not aligned to a byte boundary.  All of the
+  input data so far will be available to the decompressor, as for Z_SYNC_FLUSH.
+  This completes the current deflate block and follows it with an empty fixed
+  codes block that is 10 bits long.  This assures that enough bytes are output
+  in order for the decompressor to finish the block before the empty fixed
+  codes block.
+
+    If flush is set to Z_BLOCK, a deflate block is completed and emitted, as
+  for Z_SYNC_FLUSH, but the output is not aligned on a byte boundary, and up to
+  seven bits of the current block are held to be written as the next byte after
+  the next deflate block is completed.  In this case, the decompressor may not
+  be provided enough bits at this point in order to complete decompression of
+  the data provided so far to the compressor.  It may need to wait for the next
+  block to be emitted.  This is for advanced applications that need to control
+  the emission of deflate blocks.
+
+    If flush is set to Z_FULL_FLUSH, all output is flushed as with
+  Z_SYNC_FLUSH, and the compression state is reset so that decompression can
+  restart from this point if previous compressed data has been damaged or if
+  random access is desired.  Using Z_FULL_FLUSH too often can seriously degrade
+  compression.
+
+    If deflate returns with avail_out == 0, this function must be called again
+  with the same value of the flush parameter and more output space (updated
+  avail_out), until the flush is complete (deflate returns with non-zero
+  avail_out).  In the case of a Z_FULL_FLUSH or Z_SYNC_FLUSH, make sure that
+  avail_out is greater than six when the flush marker begins, in order to avoid
+  repeated flush markers upon calling deflate() again when avail_out == 0.
+
+    If the parameter flush is set to Z_FINISH, pending input is processed,
+  pending output is flushed and deflate returns with Z_STREAM_END if there was
+  enough output space.  If deflate returns with Z_OK or Z_BUF_ERROR, this
+  function must be called again with Z_FINISH and more output space (updated
+  avail_out) but no more input data, until it returns with Z_STREAM_END or an
+  error.  After deflate has returned Z_STREAM_END, the only possible operations
+  on the stream are deflateReset or deflateEnd.
+
+    Z_FINISH can be used in the first deflate call after deflateInit if all the
+  compression is to be done in a single step.  In order to complete in one
+  call, avail_out must be at least the value returned by deflateBound (see
+  below).  Then deflate is guaranteed to return Z_STREAM_END.  If not enough
+  output space is provided, deflate will not return Z_STREAM_END, and it must
+  be called again as described above.
+
+    deflate() sets strm->adler to the Adler-32 checksum of all input read
+  so far (that is, total_in bytes).  If a gzip stream is being generated, then
+  strm->adler will be the CRC-32 checksum of the input read so far.  (See
+  deflateInit2 below.)
+
+    deflate() may update strm->data_type if it can make a good guess about
+  the input data type (Z_BINARY or Z_TEXT).  If in doubt, the data is
+  considered binary.  This field is only for information purposes and does not
+  affect the compression algorithm in any manner.
+
+    deflate() returns Z_OK if some progress has been made (more input
+  processed or more output produced), Z_STREAM_END if all input has been
+  consumed and all output has been produced (only when flush is set to
+  Z_FINISH), Z_STREAM_ERROR if the stream state was inconsistent (for example
+  if next_in or next_out was Z_NULL or the state was inadvertently written over
+  by the application), or Z_BUF_ERROR if no progress is possible (for example
+  avail_in or avail_out was zero).  Note that Z_BUF_ERROR is not fatal, and
+  deflate() can be called again with more input and more output space to
+  continue compressing.
+*/
+
+
+ZEXTERN int ZEXPORT deflateEnd(z_streamp strm);
+/*
+     All dynamically allocated data structures for this stream are freed.
+   This function discards any unprocessed input and does not flush any pending
+   output.
+
+     deflateEnd returns Z_OK if success, Z_STREAM_ERROR if the
+   stream state was inconsistent, Z_DATA_ERROR if the stream was freed
+   prematurely (some input or output was discarded).  In the error case, msg
+   may be set but then points to a static string (which must not be
+   deallocated).
+*/
+
+
+/*
+ZEXTERN int ZEXPORT inflateInit(z_streamp strm);
+
+     Initializes the internal stream state for decompression.  The fields
+   next_in, avail_in, zalloc, zfree and opaque must be initialized before by
+   the caller.  In the current version of inflate, the provided input is not
+   read or consumed.  The allocation of a sliding window will be deferred to
+   the first call of inflate (if the decompression does not complete on the
+   first call).  If zalloc and zfree are set to Z_NULL, inflateInit updates
+   them to use default allocation functions.  total_in, total_out, adler, and
+   msg are initialized.
+
+     inflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
+   version assumed by the caller, or Z_STREAM_ERROR if the parameters are
+   invalid, such as a null pointer to the structure.  msg is set to null if
+   there is no error message.  inflateInit does not perform any decompression.
+   Actual decompression will be done by inflate().  So next_in, and avail_in,
+   next_out, and avail_out are unused and unchanged.  The current
+   implementation of inflateInit() does not process any header information --
+   that is deferred until inflate() is called.
+*/
+
+
+ZEXTERN int ZEXPORT inflate(z_streamp strm, int flush);
+/*
+    inflate decompresses as much data as possible, and stops when the input
+  buffer becomes empty or the output buffer becomes full.  It may introduce
+  some output latency (reading input without producing any output) except when
+  forced to flush.
+
+  The detailed semantics are as follows.  inflate performs one or both of the
+  following actions:
+
+  - Decompress more input starting at next_in and update next_in and avail_in
+    accordingly.  If not all input can be processed (because there is not
+    enough room in the output buffer), then next_in and avail_in are updated
+    accordingly, and processing will resume at this point for the next call of
+    inflate().
+
+  - Generate more output starting at next_out and update next_out and avail_out
+    accordingly.  inflate() provides as much output as possible, until there is
+    no more input data or no more space in the output buffer (see below about
+    the flush parameter).
+
+    Before the call of inflate(), the application should ensure that at least
+  one of the actions is possible, by providing more input and/or consuming more
+  output, and updating the next_* and avail_* values accordingly.  If the
+  caller of inflate() does not provide both available input and available
+  output space, it is possible that there will be no progress made.  The
+  application can consume the uncompressed output when it wants, for example
+  when the output buffer is full (avail_out == 0), or after each call of
+  inflate().  If inflate returns Z_OK and with zero avail_out, it must be
+  called again after making room in the output buffer because there might be
+  more output pending.
+
+    The flush parameter of inflate() can be Z_NO_FLUSH, Z_SYNC_FLUSH, Z_FINISH,
+  Z_BLOCK, or Z_TREES.  Z_SYNC_FLUSH requests that inflate() flush as much
+  output as possible to the output buffer.  Z_BLOCK requests that inflate()
+  stop if and when it gets to the next deflate block boundary.  When decoding
+  the zlib or gzip format, this will cause inflate() to return immediately
+  after the header and before the first block.  When doing a raw inflate,
+  inflate() will go ahead and process the first block, and will return when it
+  gets to the end of that block, or when it runs out of data.
+
+    The Z_BLOCK option assists in appending to or combining deflate streams.
+  To assist in this, on return inflate() always sets strm->data_type to the
+  number of unused bits in the input taken from strm->next_in, plus 64 if
+  inflate() is currently decoding the last block in the deflate stream, plus
+  128 if inflate() returned immediately after decoding an end-of-block code or
+  decoding the complete header up to just before the first byte of the deflate
+  stream.  The end-of-block will not be indicated until all of the uncompressed
+  data from that block has been written to strm->next_out.  The number of
+  unused bits may in general be greater than seven, except when bit 7 of
+  data_type is set, in which case the number of unused bits will be less than
+  eight.  data_type is set as noted here every time inflate() returns for all
+  flush options, and so can be used to determine the amount of currently
+  consumed input in bits.
+
+    The Z_TREES option behaves as Z_BLOCK does, but it also returns when the
+  end of each deflate block header is reached, before any actual data in that
+  block is decoded.  This allows the caller to determine the length of the
+  deflate block header for later use in random access within a deflate block.
+  256 is added to the value of strm->data_type when inflate() returns
+  immediately after reaching the end of the deflate block header.
+
+    inflate() should normally be called until it returns Z_STREAM_END or an
+  error.  However if all decompression is to be performed in a single step (a
+  single call of inflate), the parameter flush should be set to Z_FINISH.  In
+  this case all pending input is processed and all pending output is flushed;
+  avail_out must be large enough to hold all of the uncompressed data for the
+  operation to complete.  (The size of the uncompressed data may have been
+  saved by the compressor for this purpose.)  The use of Z_FINISH is not
+  required to perform an inflation in one step.  However it may be used to
+  inform inflate that a faster approach can be used for the single inflate()
+  call.  Z_FINISH also informs inflate to not maintain a sliding window if the
+  stream completes, which reduces inflate's memory footprint.  If the stream
+  does not complete, either because not all of the stream is provided or not
+  enough output space is provided, then a sliding window will be allocated and
+  inflate() can be called again to continue the operation as if Z_NO_FLUSH had
+  been used.
+
+     In this implementation, inflate() always flushes as much output as
+  possible to the output buffer, and always uses the faster approach on the
+  first call.  So the effects of the flush parameter in this implementation are
+  on the return value of inflate() as noted below, when inflate() returns early
+  when Z_BLOCK or Z_TREES is used, and when inflate() avoids the allocation of
+  memory for a sliding window when Z_FINISH is used.
+
+     If a preset dictionary is needed after this call (see inflateSetDictionary
+  below), inflate sets strm->adler to the Adler-32 checksum of the dictionary
+  chosen by the compressor and returns Z_NEED_DICT; otherwise it sets
+  strm->adler to the Adler-32 checksum of all output produced so far (that is,
+  total_out bytes) and returns Z_OK, Z_STREAM_END or an error code as described
+  below.  At the end of the stream, inflate() checks that its computed Adler-32
+  checksum is equal to that saved by the compressor and returns Z_STREAM_END
+  only if the checksum is correct.
+
+    inflate() can decompress and check either zlib-wrapped or gzip-wrapped
+  deflate data.  The header type is detected automatically, if requested when
+  initializing with inflateInit2().  Any information contained in the gzip
+  header is not retained unless inflateGetHeader() is used.  When processing
+  gzip-wrapped deflate data, strm->adler32 is set to the CRC-32 of the output
+  produced so far.  The CRC-32 is checked against the gzip trailer, as is the
+  uncompressed length, modulo 2^32.
+
+    inflate() returns Z_OK if some progress has been made (more input processed
+  or more output produced), Z_STREAM_END if the end of the compressed data has
+  been reached and all uncompressed output has been produced, Z_NEED_DICT if a
+  preset dictionary is needed at this point, Z_DATA_ERROR if the input data was
+  corrupted (input stream not conforming to the zlib format or incorrect check
+  value, in which case strm->msg points to a string with a more specific
+  error), Z_STREAM_ERROR if the stream structure was inconsistent (for example
+  next_in or next_out was Z_NULL, or the state was inadvertently written over
+  by the application), Z_MEM_ERROR if there was not enough memory, Z_BUF_ERROR
+  if no progress was possible or if there was not enough room in the output
+  buffer when Z_FINISH is used.  Note that Z_BUF_ERROR is not fatal, and
+  inflate() can be called again with more input and more output space to
+  continue decompressing.  If Z_DATA_ERROR is returned, the application may
+  then call inflateSync() to look for a good compression block if a partial
+  recovery of the data is to be attempted.
+*/
+
+
+ZEXTERN int ZEXPORT inflateEnd(z_streamp strm);
+/*
+     All dynamically allocated data structures for this stream are freed.
+   This function discards any unprocessed input and does not flush any pending
+   output.
+
+     inflateEnd returns Z_OK if success, or Z_STREAM_ERROR if the stream state
+   was inconsistent.
+*/
+
+
+                        /* Advanced functions */
+
+/*
+    The following functions are needed only in some special applications.
+*/
+
+/*
+ZEXTERN int ZEXPORT deflateInit2(z_streamp strm,
+                                 int level,
+                                 int method,
+                                 int windowBits,
+                                 int memLevel,
+                                 int strategy);
+
+     This is another version of deflateInit with more compression options.  The
+   fields zalloc, zfree and opaque must be initialized before by the caller.
+
+     The method parameter is the compression method.  It must be Z_DEFLATED in
+   this version of the library.
+
+     The windowBits parameter is the base two logarithm of the window size
+   (the size of the history buffer).  It should be in the range 8..15 for this
+   version of the library.  Larger values of this parameter result in better
+   compression at the expense of memory usage.  The default value is 15 if
+   deflateInit is used instead.
+
+     For the current implementation of deflate(), a windowBits value of 8 (a
+   window size of 256 bytes) is not supported.  As a result, a request for 8
+   will result in 9 (a 512-byte window).  In that case, providing 8 to
+   inflateInit2() will result in an error when the zlib header with 9 is
+   checked against the initialization of inflate().  The remedy is to not use 8
+   with deflateInit2() with this initialization, or at least in that case use 9
+   with inflateInit2().
+
+     windowBits can also be -8..-15 for raw deflate.  In this case, -windowBits
+   determines the window size.  deflate() will then generate raw deflate data
+   with no zlib header or trailer, and will not compute a check value.
+
+     windowBits can also be greater than 15 for optional gzip encoding.  Add
+   16 to windowBits to write a simple gzip header and trailer around the
+   compressed data instead of a zlib wrapper.  The gzip header will have no
+   file name, no extra data, no comment, no modification time (set to zero), no
+   header crc, and the operating system will be set to the appropriate value,
+   if the operating system was determined at compile time.  If a gzip stream is
+   being written, strm->adler is a CRC-32 instead of an Adler-32.
+
+     For raw deflate or gzip encoding, a request for a 256-byte window is
+   rejected as invalid, since only the zlib header provides a means of
+   transmitting the window size to the decompressor.
+
+     The memLevel parameter specifies how much memory should be allocated
+   for the internal compression state.  memLevel=1 uses minimum memory but is
+   slow and reduces compression ratio; memLevel=9 uses maximum memory for
+   optimal speed.  The default value is 8.  See zconf.h for total memory usage
+   as a function of windowBits and memLevel.
+
+     The strategy parameter is used to tune the compression algorithm.  Use the
+   value Z_DEFAULT_STRATEGY for normal data, Z_FILTERED for data produced by a
+   filter (or predictor), Z_RLE to limit match distances to one (run-length
+   encoding), or Z_HUFFMAN_ONLY to force Huffman encoding only (no string
+   matching).  Filtered data consists mostly of small values with a somewhat
+   random distribution, as produced by the PNG filters.  In this case, the
+   compression algorithm is tuned to compress them better.  The effect of
+   Z_FILTERED is to force more Huffman coding and less string matching than the
+   default; it is intermediate between Z_DEFAULT_STRATEGY and Z_HUFFMAN_ONLY.
+   Z_RLE is almost as fast as Z_HUFFMAN_ONLY, but should give better
+   compression for PNG image data than Huffman only.  The degree of string
+   matching from most to none is: Z_DEFAULT_STRATEGY, Z_FILTERED, Z_RLE, then
+   Z_HUFFMAN_ONLY. The strategy parameter affects the compression ratio but
+   never the correctness of the compressed output, even if it is not set
+   optimally for the given data.  Z_FIXED uses the default string matching, but
+   prevents the use of dynamic Huffman codes, allowing for a simpler decoder
+   for special applications.
+
+     deflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_STREAM_ERROR if any parameter is invalid (such as an invalid
+   method), or Z_VERSION_ERROR if the zlib library version (zlib_version) is
+   incompatible with the version assumed by the caller (ZLIB_VERSION).  msg is
+   set to null if there is no error message.  deflateInit2 does not perform any
+   compression: this will be done by deflate().
+*/
+
+ZEXTERN int ZEXPORT deflateSetDictionary(z_streamp strm,
+                                         const Bytef *dictionary,
+                                         uInt  dictLength);
+/*
+     Initializes the compression dictionary from the given byte sequence
+   without producing any compressed output.  When using the zlib format, this
+   function must be called immediately after deflateInit, deflateInit2 or
+   deflateReset, and before any call of deflate.  When doing raw deflate, this
+   function must be called either before any call of deflate, or immediately
+   after the completion of a deflate block, i.e. after all input has been
+   consumed and all output has been delivered when using any of the flush
+   options Z_BLOCK, Z_PARTIAL_FLUSH, Z_SYNC_FLUSH, or Z_FULL_FLUSH.  The
+   compressor and decompressor must use exactly the same dictionary (see
+   inflateSetDictionary).
+
+     The dictionary should consist of strings (byte sequences) that are likely
+   to be encountered later in the data to be compressed, with the most commonly
+   used strings preferably put towards the end of the dictionary.  Using a
+   dictionary is most useful when the data to be compressed is short and can be
+   predicted with good accuracy; the data can then be compressed better than
+   with the default empty dictionary.
+
+     Depending on the size of the compression data structures selected by
+   deflateInit or deflateInit2, a part of the dictionary may in effect be
+   discarded, for example if the dictionary is larger than the window size
+   provided in deflateInit or deflateInit2.  Thus the strings most likely to be
+   useful should be put at the end of the dictionary, not at the front.  In
+   addition, the current implementation of deflate will use at most the window
+   size minus 262 bytes of the provided dictionary.
+
+     Upon return of this function, strm->adler is set to the Adler-32 value
+   of the dictionary; the decompressor may later use this value to determine
+   which dictionary has been used by the compressor.  (The Adler-32 value
+   applies to the whole dictionary even if only a subset of the dictionary is
+   actually used by the compressor.) If a raw deflate was requested, then the
+   Adler-32 value is not computed and strm->adler is not set.
+
+     deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a
+   parameter is invalid (e.g.  dictionary being Z_NULL) or the stream state is
+   inconsistent (for example if deflate has already been called for this stream
+   or if not at a block boundary for raw deflate).  deflateSetDictionary does
+   not perform any compression: this will be done by deflate().
+*/
+
+ZEXTERN int ZEXPORT deflateGetDictionary(z_streamp strm,
+                                         Bytef *dictionary,
+                                         uInt  *dictLength);
+/*
+     Returns the sliding dictionary being maintained by deflate.  dictLength is
+   set to the number of bytes in the dictionary, and that many bytes are copied
+   to dictionary.  dictionary must have enough space, where 32768 bytes is
+   always enough.  If deflateGetDictionary() is called with dictionary equal to
+   Z_NULL, then only the dictionary length is returned, and nothing is copied.
+   Similarly, if dictLength is Z_NULL, then it is not set.
+
+     deflateGetDictionary() may return a length less than the window size, even
+   when more than the window size in input has been provided. It may return up
+   to 258 bytes less in that case, due to how zlib's implementation of deflate
+   manages the sliding window and lookahead for matches, where matches can be
+   up to 258 bytes long. If the application needs the last window-size bytes of
+   input, then that would need to be saved by the application outside of zlib.
+
+     deflateGetDictionary returns Z_OK on success, or Z_STREAM_ERROR if the
+   stream state is inconsistent.
+*/
+
+ZEXTERN int ZEXPORT deflateCopy(z_streamp dest,
+                                z_streamp source);
+/*
+     Sets the destination stream as a complete copy of the source stream.
+
+     This function can be useful when several compression strategies will be
+   tried, for example when there are several ways of pre-processing the input
+   data with a filter.  The streams that will be discarded should then be freed
+   by calling deflateEnd.  Note that deflateCopy duplicates the internal
+   compression state which can be quite large, so this strategy is slow and can
+   consume lots of memory.
+
+     deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
+   enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
+   (such as zalloc being Z_NULL).  msg is left unchanged in both source and
+   destination.
+*/
+
+ZEXTERN int ZEXPORT deflateReset(z_streamp strm);
+/*
+     This function is equivalent to deflateEnd followed by deflateInit, but
+   does not free and reallocate the internal compression state.  The stream
+   will leave the compression level and any other attributes that may have been
+   set unchanged.  total_in, total_out, adler, and msg are initialized.
+
+     deflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent (such as zalloc or state being Z_NULL).
+*/
+
+ZEXTERN int ZEXPORT deflateParams(z_streamp strm,
+                                  int level,
+                                  int strategy);
+/*
+     Dynamically update the compression level and compression strategy.  The
+   interpretation of level and strategy is as in deflateInit2().  This can be
+   used to switch between compression and straight copy of the input data, or
+   to switch to a different kind of input data requiring a different strategy.
+   If the compression approach (which is a function of the level) or the
+   strategy is changed, and if there have been any deflate() calls since the
+   state was initialized or reset, then the input available so far is
+   compressed with the old level and strategy using deflate(strm, Z_BLOCK).
+   There are three approaches for the compression levels 0, 1..3, and 4..9
+   respectively.  The new level and strategy will take effect at the next call
+   of deflate().
+
+     If a deflate(strm, Z_BLOCK) is performed by deflateParams(), and it does
+   not have enough output space to complete, then the parameter change will not
+   take effect.  In this case, deflateParams() can be called again with the
+   same parameters and more output space to try again.
+
+     In order to assure a change in the parameters on the first try, the
+   deflate stream should be flushed using deflate() with Z_BLOCK or other flush
+   request until strm.avail_out is not zero, before calling deflateParams().
+   Then no more input data should be provided before the deflateParams() call.
+   If this is done, the old level and strategy will be applied to the data
+   compressed before deflateParams(), and the new level and strategy will be
+   applied to the data compressed after deflateParams().
+
+     deflateParams returns Z_OK on success, Z_STREAM_ERROR if the source stream
+   state was inconsistent or if a parameter was invalid, or Z_BUF_ERROR if
+   there was not enough output space to complete the compression of the
+   available input data before a change in the strategy or approach.  Note that
+   in the case of a Z_BUF_ERROR, the parameters are not changed.  A return
+   value of Z_BUF_ERROR is not fatal, in which case deflateParams() can be
+   retried with more output space.
+*/
+
+ZEXTERN int ZEXPORT deflateTune(z_streamp strm,
+                                int good_length,
+                                int max_lazy,
+                                int nice_length,
+                                int max_chain);
+/*
+     Fine tune deflate's internal compression parameters.  This should only be
+   used by someone who understands the algorithm used by zlib's deflate for
+   searching for the best matching string, and even then only by the most
+   fanatic optimizer trying to squeeze out the last compressed bit for their
+   specific input data.  Read the deflate.c source code for the meaning of the
+   max_lazy, good_length, nice_length, and max_chain parameters.
+
+     deflateTune() can be called after deflateInit() or deflateInit2(), and
+   returns Z_OK on success, or Z_STREAM_ERROR for an invalid deflate stream.
+ */
+
+ZEXTERN uLong ZEXPORT deflateBound(z_streamp strm, uLong sourceLen);
+ZEXTERN z_size_t ZEXPORT deflateBound_z(z_streamp strm, z_size_t sourceLen);
+/*
+     deflateBound() returns an upper bound on the compressed size after
+   deflation of sourceLen bytes.  It must be called after deflateInit() or
+   deflateInit2(), and after deflateSetHeader(), if used.  This would be used
+   to allocate an output buffer for deflation in a single pass, and so would be
+   called before deflate().  If that first deflate() call is provided the
+   sourceLen input bytes, an output buffer allocated to the size returned by
+   deflateBound(), and the flush value Z_FINISH, then deflate() is guaranteed
+   to return Z_STREAM_END.  Note that it is possible for the compressed size to
+   be larger than the value returned by deflateBound() if flush options other
+   than Z_FINISH or Z_NO_FLUSH are used.
+
+     delfateBound_z() is the same, but takes and returns a size_t length.  Note
+   that a long is 32 bits on Windows.
+*/
+
+ZEXTERN int ZEXPORT deflatePending(z_streamp strm,
+                                   unsigned *pending,
+                                   int *bits);
+/*
+     deflatePending() returns the number of bytes and bits of output that have
+   been generated, but not yet provided in the available output.  The bytes not
+   provided would be due to the available output space having being consumed.
+   The number of bits of output not provided are between 0 and 7, where they
+   await more bits to join them in order to fill out a full byte.  If pending
+   or bits are Z_NULL, then those values are not set.
+
+     deflatePending returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent.  If an int is 16 bits and memLevel is 9, then
+   it is possible for the number of pending bytes to not fit in an unsigned. In
+   that case Z_BUF_ERROR is returned and *pending is set to the maximum value
+   of an unsigned.
+ */
+
+ZEXTERN int ZEXPORT deflateUsed(z_streamp strm,
+                                int *bits);
+/*
+     deflateUsed() returns in *bits the most recent number of deflate bits used
+   in the last byte when flushing to a byte boundary. The result is in 1..8, or
+   0 if there has not yet been a flush. This helps determine the location of
+   the last bit of a deflate stream.
+
+     deflateUsed returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent.
+ */
+
+ZEXTERN int ZEXPORT deflatePrime(z_streamp strm,
+                                 int bits,
+                                 int value);
+/*
+     deflatePrime() inserts bits in the deflate output stream.  The intent
+   is that this function is used to start off the deflate output with the bits
+   leftover from a previous deflate stream when appending to it.  As such, this
+   function can only be used for raw deflate, and must be used before the first
+   deflate() call after a deflateInit2() or deflateReset().  bits must be less
+   than or equal to 16, and that many of the least significant bits of value
+   will be inserted in the output.
+
+     deflatePrime returns Z_OK if success, Z_BUF_ERROR if there was not enough
+   room in the internal buffer to insert the bits, or Z_STREAM_ERROR if the
+   source stream state was inconsistent.
+*/
+
+ZEXTERN int ZEXPORT deflateSetHeader(z_streamp strm,
+                                     gz_headerp head);
+/*
+     deflateSetHeader() provides gzip header information for when a gzip
+   stream is requested by deflateInit2().  deflateSetHeader() may be called
+   after deflateInit2() or deflateReset() and before the first call of
+   deflate().  The text, time, os, extra field, name, and comment information
+   in the provided gz_header structure are written to the gzip header (xflag is
+   ignored -- the extra flags are set according to the compression level).  The
+   caller must assure that, if not Z_NULL, name and comment are terminated with
+   a zero byte, and that if extra is not Z_NULL, that extra_len bytes are
+   available there.  If hcrc is true, a gzip header crc is included.  Note that
+   the current versions of the command-line version of gzip (up through version
+   1.3.x) do not support header crc's, and will report that it is a "multi-part
+   gzip file" and give up.
+
+     If deflateSetHeader is not used, the default gzip header has text false,
+   the time set to zero, and os set to the current operating system, with no
+   extra, name, or comment fields.  The gzip header is returned to the default
+   state by deflateReset().
+
+     deflateSetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent.
+*/
+
+/*
+ZEXTERN int ZEXPORT inflateInit2(z_streamp strm,
+                                 int windowBits);
+
+     This is another version of inflateInit with an extra parameter.  The
+   fields next_in, avail_in, zalloc, zfree and opaque must be initialized
+   before by the caller.
+
+     The windowBits parameter is the base two logarithm of the maximum window
+   size (the size of the history buffer).  It should be in the range 8..15 for
+   this version of the library.  The default value is 15 if inflateInit is used
+   instead.  windowBits must be greater than or equal to the windowBits value
+   provided to deflateInit2() while compressing, or it must be equal to 15 if
+   deflateInit2() was not used.  If a compressed stream with a larger window
+   size is given as input, inflate() will return with the error code
+   Z_DATA_ERROR instead of trying to allocate a larger window.
+
+     windowBits can also be zero to request that inflate use the window size in
+   the zlib header of the compressed stream.
+
+     windowBits can also be -8..-15 for raw inflate.  In this case, -windowBits
+   determines the window size.  inflate() will then process raw deflate data,
+   not looking for a zlib or gzip header, not generating a check value, and not
+   looking for any check values for comparison at the end of the stream.  This
+   is for use with other formats that use the deflate compressed data format
+   such as zip.  Those formats provide their own check values.  If a custom
+   format is developed using the raw deflate format for compressed data, it is
+   recommended that a check value such as an Adler-32 or a CRC-32 be applied to
+   the uncompressed data as is done in the zlib, gzip, and zip formats.  For
+   most applications, the zlib format should be used as is.  Note that comments
+   above on the use in deflateInit2() applies to the magnitude of windowBits.
+
+     windowBits can also be greater than 15 for optional gzip decoding.  Add
+   32 to windowBits to enable zlib and gzip decoding with automatic header
+   detection, or add 16 to decode only the gzip format (the zlib format will
+   return a Z_DATA_ERROR).  If a gzip stream is being decoded, strm->adler is a
+   CRC-32 instead of an Adler-32.  Unlike the gunzip utility and gzread() (see
+   below), inflate() will *not* automatically decode concatenated gzip members.
+   inflate() will return Z_STREAM_END at the end of the gzip member.  The state
+   would need to be reset to continue decoding a subsequent gzip member.  This
+   *must* be done if there is more data after a gzip member, in order for the
+   decompression to be compliant with the gzip standard (RFC 1952).
+
+     inflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
+   version assumed by the caller, or Z_STREAM_ERROR if the parameters are
+   invalid, such as a null pointer to the structure.  msg is set to null if
+   there is no error message.  inflateInit2 does not perform any decompression
+   apart from possibly reading the zlib header if present: actual decompression
+   will be done by inflate().  (So next_in and avail_in may be modified, but
+   next_out and avail_out are unused and unchanged.) The current implementation
+   of inflateInit2() does not process any header information -- that is
+   deferred until inflate() is called.
+*/
+
+ZEXTERN int ZEXPORT inflateSetDictionary(z_streamp strm,
+                                         const Bytef *dictionary,
+                                         uInt  dictLength);
+/*
+     Initializes the decompression dictionary from the given uncompressed byte
+   sequence.  This function must be called immediately after a call of inflate,
+   if that call returned Z_NEED_DICT.  The dictionary chosen by the compressor
+   can be determined from the Adler-32 value returned by that call of inflate.
+   The compressor and decompressor must use exactly the same dictionary (see
+   deflateSetDictionary).  For raw inflate, this function can be called at any
+   time to set the dictionary.  If the provided dictionary is smaller than the
+   window and there is already data in the window, then the provided dictionary
+   will amend what's there.  The application must insure that the dictionary
+   that was used for compression is provided.
+
+     inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a
+   parameter is invalid (e.g.  dictionary being Z_NULL) or the stream state is
+   inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the
+   expected one (incorrect Adler-32 value).  inflateSetDictionary does not
+   perform any decompression: this will be done by subsequent calls of
+   inflate().
+*/
+
+ZEXTERN int ZEXPORT inflateGetDictionary(z_streamp strm,
+                                         Bytef *dictionary,
+                                         uInt  *dictLength);
+/*
+     Returns the sliding dictionary being maintained by inflate.  dictLength is
+   set to the number of bytes in the dictionary, and that many bytes are copied
+   to dictionary.  dictionary must have enough space, where 32768 bytes is
+   always enough.  If inflateGetDictionary() is called with dictionary equal to
+   Z_NULL, then only the dictionary length is returned, and nothing is copied.
+   Similarly, if dictLength is Z_NULL, then it is not set.
+
+     inflateGetDictionary returns Z_OK on success, or Z_STREAM_ERROR if the
+   stream state is inconsistent.
+*/
+
+ZEXTERN int ZEXPORT inflateSync(z_streamp strm);
+/*
+     Skips invalid compressed data until a possible full flush point (see above
+   for the description of deflate with Z_FULL_FLUSH) can be found, or until all
+   available input is skipped.  No output is provided.
+
+     inflateSync searches for a 00 00 FF FF pattern in the compressed data.
+   All full flush points have this pattern, but not all occurrences of this
+   pattern are full flush points.
+
+     inflateSync returns Z_OK if a possible full flush point has been found,
+   Z_BUF_ERROR if no more input was provided, Z_DATA_ERROR if no flush point
+   has been found, or Z_STREAM_ERROR if the stream structure was inconsistent.
+   In the success case, the application may save the current value of total_in
+   which indicates where valid compressed data was found.  In the error case,
+   the application may repeatedly call inflateSync, providing more input each
+   time, until success or end of the input data.
+*/
+
+ZEXTERN int ZEXPORT inflateCopy(z_streamp dest,
+                                z_streamp source);
+/*
+     Sets the destination stream as a complete copy of the source stream.
+
+     This function can be useful when randomly accessing a large stream.  The
+   first pass through the stream can periodically record the inflate state,
+   allowing restarting inflate at those points when randomly accessing the
+   stream.
+
+     inflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
+   enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
+   (such as zalloc being Z_NULL).  msg is left unchanged in both source and
+   destination.
+*/
+
+ZEXTERN int ZEXPORT inflateReset(z_streamp strm);
+/*
+     This function is equivalent to inflateEnd followed by inflateInit,
+   but does not free and reallocate the internal decompression state.  The
+   stream will keep attributes that may have been set by inflateInit2.
+   total_in, total_out, adler, and msg are initialized.
+
+     inflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent (such as zalloc or state being Z_NULL).
+*/
+
+ZEXTERN int ZEXPORT inflateReset2(z_streamp strm,
+                                  int windowBits);
+/*
+     This function is the same as inflateReset, but it also permits changing
+   the wrap and window size requests.  The windowBits parameter is interpreted
+   the same as it is for inflateInit2.  If the window size is changed, then the
+   memory allocated for the window is freed, and the window will be reallocated
+   by inflate() if needed.
+
+     inflateReset2 returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent (such as zalloc or state being Z_NULL), or if
+   the windowBits parameter is invalid.
+*/
+
+ZEXTERN int ZEXPORT inflatePrime(z_streamp strm,
+                                 int bits,
+                                 int value);
+/*
+     This function inserts bits in the inflate input stream.  The intent is to
+   use inflatePrime() to start inflating at a bit position in the middle of a
+   byte.  The provided bits will be used before any bytes are used from
+   next_in.  This function should be used with raw inflate, before the first
+   inflate() call, after inflateInit2() or inflateReset().  It can also be used
+   after an inflate() return indicates the end of a deflate block or header
+   when using Z_BLOCK.  bits must be less than or equal to 16, and that many of
+   the least significant bits of value will be inserted in the input.  The
+   other bits in value can be non-zero, and will be ignored.
+
+     If bits is negative, then the input stream bit buffer is emptied.  Then
+   inflatePrime() can be called again to put bits in the buffer.  This is used
+   to clear out bits leftover after feeding inflate a block description prior
+   to feeding inflate codes.
+
+     inflatePrime returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent, or if bits is out of range.  If inflate was
+   in the middle of processing a header, trailer, or stored block lengths, then
+   it is possible for there to be only eight bits available in the bit buffer.
+   In that case, bits > 8 is considered out of range.  However, when used as
+   outlined above, there will always be 16 bits available in the buffer for
+   insertion.  As noted in its documentation above, inflate records the number
+   of bits in the bit buffer on return in data_type. 32 minus that is the
+   number of bits available for insertion.  inflatePrime does not update
+   data_type with the new number of bits in buffer.
+*/
+
+ZEXTERN long ZEXPORT inflateMark(z_streamp strm);
+/*
+     This function returns two values, one in the lower 16 bits of the return
+   value, and the other in the remaining upper bits, obtained by shifting the
+   return value down 16 bits.  If the upper value is -1 and the lower value is
+   zero, then inflate() is currently decoding information outside of a block.
+   If the upper value is -1 and the lower value is non-zero, then inflate is in
+   the middle of a stored block, with the lower value equaling the number of
+   bytes from the input remaining to copy.  If the upper value is not -1, then
+   it is the number of bits back from the current bit position in the input of
+   the code (literal or length/distance pair) currently being processed.  In
+   that case the lower value is the number of bytes already emitted for that
+   code.
+
+     A code is being processed if inflate is waiting for more input to complete
+   decoding of the code, or if it has completed decoding but is waiting for
+   more output space to write the literal or match data.
+
+     inflateMark() is used to mark locations in the input data for random
+   access, which may be at bit positions, and to note those cases where the
+   output of a code may span boundaries of random access blocks.  The current
+   location in the input stream can be determined from avail_in and data_type
+   as noted in the description for the Z_BLOCK flush parameter for inflate.
+
+     inflateMark returns the value noted above, or -65536 if the provided
+   source stream state was inconsistent.
+*/
+
+ZEXTERN int ZEXPORT inflateGetHeader(z_streamp strm,
+                                     gz_headerp head);
+/*
+     inflateGetHeader() requests that gzip header information be stored in the
+   provided gz_header structure.  inflateGetHeader() may be called after
+   inflateInit2() or inflateReset(), and before the first call of inflate().
+   As inflate() processes the gzip stream, head->done is zero until the header
+   is completed, at which time head->done is set to one.  If a zlib stream is
+   being decoded, then head->done is set to -1 to indicate that there will be
+   no gzip header information forthcoming.  Note that Z_BLOCK or Z_TREES can be
+   used to force inflate() to return immediately after header processing is
+   complete and before any actual data is decompressed.
+
+     The text, time, xflags, and os fields are filled in with the gzip header
+   contents.  hcrc is set to true if there is a header CRC.  (The header CRC
+   was valid if done is set to one.)  The extra, name, and comment pointers
+   much each be either Z_NULL or point to space to store that information from
+   the header.  If extra is not Z_NULL, then extra_max contains the maximum
+   number of bytes that can be written to extra.  Once done is true, extra_len
+   contains the actual extra field length, and extra contains the extra field,
+   or that field truncated if extra_max is less than extra_len.  If name is not
+   Z_NULL, then up to name_max characters, including the terminating zero, are
+   written there.  If comment is not Z_NULL, then up to comm_max characters,
+   including the terminating zero, are written there.  The application can tell
+   that the name or comment did not fit in the provided space by the absence of
+   a terminating zero.  If any of extra, name, or comment are not present in
+   the header, then that field's pointer is set to Z_NULL.  This allows the use
+   of deflateSetHeader() with the returned structure to duplicate the header.
+   Note that if those fields initially pointed to allocated memory, then the
+   application will need to save them elsewhere so that they can be eventually
+   freed.
+
+     If inflateGetHeader is not used, then the header information is simply
+   discarded.  The header is always checked for validity, including the header
+   CRC if present.  inflateReset() will reset the process to discard the header
+   information.  The application would need to call inflateGetHeader() again to
+   retrieve the header from the next gzip stream.
+
+     inflateGetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
+   stream state was inconsistent.
+*/
+
+/*
+ZEXTERN int ZEXPORT inflateBackInit(z_streamp strm, int windowBits,
+                                    unsigned char FAR *window);
+
+     Initialize the internal stream state for decompression using inflateBack()
+   calls.  The fields zalloc, zfree and opaque in strm must be initialized
+   before the call.  If zalloc and zfree are Z_NULL, then the default library-
+   derived memory allocation routines are used.  windowBits is the base two
+   logarithm of the window size, in the range 8..15.  window is a caller
+   supplied buffer of that size.  Except for special applications where it is
+   assured that deflate was used with small window sizes, windowBits must be 15
+   and a 32K byte window must be supplied to be able to decompress general
+   deflate streams.
+
+     See inflateBack() for the usage of these routines.
+
+     inflateBackInit will return Z_OK on success, Z_STREAM_ERROR if any of
+   the parameters are invalid, Z_MEM_ERROR if the internal state could not be
+   allocated, or Z_VERSION_ERROR if the version of the library does not match
+   the version of the header file.
+*/
+
+typedef unsigned (*in_func)(void FAR *,
+                            z_const unsigned char FAR * FAR *);
+typedef int (*out_func)(void FAR *, unsigned char FAR *, unsigned);
+
+ZEXTERN int ZEXPORT inflateBack(z_streamp strm,
+                                in_func in, void FAR *in_desc,
+                                out_func out, void FAR *out_desc);
+/*
+     inflateBack() does a raw inflate with a single call using a call-back
+   interface for input and output.  This is potentially more efficient than
+   inflate() for file i/o applications, in that it avoids copying between the
+   output and the sliding window by simply making the window itself the output
+   buffer.  inflate() can be faster on modern CPUs when used with large
+   buffers.  inflateBack() trusts the application to not change the output
+   buffer passed by the output function, at least until inflateBack() returns.
+
+     inflateBackInit() must be called first to allocate the internal state
+   and to initialize the state with the user-provided window buffer.
+   inflateBack() may then be used multiple times to inflate a complete, raw
+   deflate stream with each call.  inflateBackEnd() is then called to free the
+   allocated state.
+
+     A raw deflate stream is one with no zlib or gzip header or trailer.
+   This routine would normally be used in a utility that reads zip or gzip
+   files and writes out uncompressed files.  The utility would decode the
+   header and process the trailer on its own, hence this routine expects only
+   the raw deflate stream to decompress.  This is different from the default
+   behavior of inflate(), which expects a zlib header and trailer around the
+   deflate stream.
+
+     inflateBack() uses two subroutines supplied by the caller that are then
+   called by inflateBack() for input and output.  inflateBack() calls those
+   routines until it reads a complete deflate stream and writes out all of the
+   uncompressed data, or until it encounters an error.  The function's
+   parameters and return types are defined above in the in_func and out_func
+   typedefs.  inflateBack() will call in(in_desc, &buf) which should return the
+   number of bytes of provided input, and a pointer to that input in buf.  If
+   there is no input available, in() must return zero -- buf is ignored in that
+   case -- and inflateBack() will return a buffer error.  inflateBack() will
+   call out(out_desc, buf, len) to write the uncompressed data buf[0..len-1].
+   out() should return zero on success, or non-zero on failure.  If out()
+   returns non-zero, inflateBack() will return with an error.  Neither in() nor
+   out() are permitted to change the contents of the window provided to
+   inflateBackInit(), which is also the buffer that out() uses to write from.
+   The length written by out() will be at most the window size.  Any non-zero
+   amount of input may be provided by in().
+
+     For convenience, inflateBack() can be provided input on the first call by
+   setting strm->next_in and strm->avail_in.  If that input is exhausted, then
+   in() will be called.  Therefore strm->next_in must be initialized before
+   calling inflateBack().  If strm->next_in is Z_NULL, then in() will be called
+   immediately for input.  If strm->next_in is not Z_NULL, then strm->avail_in
+   must also be initialized, and then if strm->avail_in is not zero, input will
+   initially be taken from strm->next_in[0 ..  strm->avail_in - 1].
+
+     The in_desc and out_desc parameters of inflateBack() is passed as the
+   first parameter of in() and out() respectively when they are called.  These
+   descriptors can be optionally used to pass any information that the caller-
+   supplied in() and out() functions need to do their job.
+
+     On return, inflateBack() will set strm->next_in and strm->avail_in to
+   pass back any unused input that was provided by the last in() call.  The
+   return values of inflateBack() can be Z_STREAM_END on success, Z_BUF_ERROR
+   if in() or out() returned an error, Z_DATA_ERROR if there was a format error
+   in the deflate stream (in which case strm->msg is set to indicate the nature
+   of the error), or Z_STREAM_ERROR if the stream was not properly initialized.
+   In the case of Z_BUF_ERROR, an input or output error can be distinguished
+   using strm->next_in which will be Z_NULL only if in() returned an error.  If
+   strm->next_in is not Z_NULL, then the Z_BUF_ERROR was due to out() returning
+   non-zero.  (in() will always be called before out(), so strm->next_in is
+   assured to be defined if out() returns non-zero.)  Note that inflateBack()
+   cannot return Z_OK.
+*/
+
+ZEXTERN int ZEXPORT inflateBackEnd(z_streamp strm);
+/*
+     All memory allocated by inflateBackInit() is freed.
+
+     inflateBackEnd() returns Z_OK on success, or Z_STREAM_ERROR if the stream
+   state was inconsistent.
+*/
+
+ZEXTERN uLong ZEXPORT zlibCompileFlags(void);
+/* Return flags indicating compile-time options.
+
+    Type sizes, two bits each, 00 = 16 bits, 01 = 32, 10 = 64, 11 = other:
+     1.0: size of uInt
+     3.2: size of uLong
+     5.4: size of voidpf (pointer)
+     7.6: size of z_off_t
+
+    Compiler, assembler, and debug options:
+     8: ZLIB_DEBUG
+     9: ASMV or ASMINF -- use ASM code
+     10: ZLIB_WINAPI -- exported functions use the WINAPI calling convention
+     11: 0 (reserved)
+
+    One-time table building (smaller code, but not thread-safe if true):
+     12: BUILDFIXED -- build static block decoding tables when needed
+     13: DYNAMIC_CRC_TABLE -- build CRC calculation tables when needed
+     14,15: 0 (reserved)
+
+    Library content (indicates missing functionality):
+     16: NO_GZCOMPRESS -- gz* functions cannot compress (to avoid linking
+                          deflate code when not needed)
+     17: NO_GZIP -- deflate can't write gzip streams, and inflate can't detect
+                    and decode gzip streams (to avoid linking crc code)
+     18-19: 0 (reserved)
+
+    Operation variations (changes in library functionality):
+     20: PKZIP_BUG_WORKAROUND -- slightly more permissive inflate
+     21: FASTEST -- deflate algorithm with only one, lowest compression level
+     22,23: 0 (reserved)
+
+    The sprintf variant used by gzprintf (all zeros is best):
+     24: 0 = vs*, 1 = s* -- 1 means limited to 20 arguments after the format
+     25: 0 = *nprintf, 1 = *printf -- 1 means gzprintf() is not secure!
+     26: 0 = returns value, 1 = void -- 1 means inferred string length returned
+     27: 0 = gzprintf() present, 1 = not -- 1 means gzprintf() returns an error
+
+    Remainder:
+     28-31: 0 (reserved)
+ */
+
+#ifndef Z_SOLO
+
+                        /* utility functions */
+
+/*
+     The following utility functions are implemented on top of the basic
+   stream-oriented functions.  To simplify the interface, some default options
+   are assumed (compression level and memory usage, standard memory allocation
+   functions).  The source code of these utility functions can be modified if
+   you need special options.  The _z versions of the functions use the size_t
+   type for lengths.  Note that a long is 32 bits on Windows.
+*/
+
+ZEXTERN int ZEXPORT compress(Bytef *dest, uLongf *destLen,
+                             const Bytef *source, uLong sourceLen);
+ZEXTERN int ZEXPORT compress_z(Bytef *dest, z_size_t *destLen,
+                               const Bytef *source, z_size_t sourceLen);
+/*
+     Compresses the source buffer into the destination buffer.  sourceLen is
+   the byte length of the source buffer.  Upon entry, destLen is the total size
+   of the destination buffer, which must be at least the value returned by
+   compressBound(sourceLen).  Upon exit, destLen is the actual size of the
+   compressed data.  compress() is equivalent to compress2() with a level
+   parameter of Z_DEFAULT_COMPRESSION.
+
+     compress returns Z_OK if success, Z_MEM_ERROR if there was not
+   enough memory, Z_BUF_ERROR if there was not enough room in the output
+   buffer.
+*/
+
+ZEXTERN int ZEXPORT compress2(Bytef *dest, uLongf *destLen,
+                              const Bytef *source, uLong sourceLen,
+                              int level);
+ZEXTERN int ZEXPORT compress2_z(Bytef *dest, z_size_t *destLen,
+                                const Bytef *source, z_size_t sourceLen,
+                                int level);
+/*
+     Compresses the source buffer into the destination buffer.  The level
+   parameter has the same meaning as in deflateInit.  sourceLen is the byte
+   length of the source buffer.  Upon entry, destLen is the total size of the
+   destination buffer, which must be at least the value returned by
+   compressBound(sourceLen).  Upon exit, destLen is the actual size of the
+   compressed data.
+
+     compress2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_BUF_ERROR if there was not enough room in the output buffer,
+   Z_STREAM_ERROR if the level parameter is invalid.
+*/
+
+ZEXTERN uLong ZEXPORT compressBound(uLong sourceLen);
+ZEXTERN z_size_t ZEXPORT compressBound_z(z_size_t sourceLen);
+/*
+     compressBound() returns an upper bound on the compressed size after
+   compress() or compress2() on sourceLen bytes.  It would be used before a
+   compress() or compress2() call to allocate the destination buffer.
+*/
+
+ZEXTERN int ZEXPORT uncompress(Bytef *dest, uLongf *destLen,
+                               const Bytef *source, uLong sourceLen);
+ZEXTERN int ZEXPORT uncompress_z(Bytef *dest, z_size_t *destLen,
+                                 const Bytef *source, z_size_t sourceLen);
+/*
+     Decompresses the source buffer into the destination buffer.  sourceLen is
+   the byte length of the source buffer.  On entry, *destLen is the total size
+   of the destination buffer, which must be large enough to hold the entire
+   uncompressed data.  (The size of the uncompressed data must have been saved
+   previously by the compressor and transmitted to the decompressor by some
+   mechanism outside the scope of this compression library.)  On exit, *destLen
+   is the actual size of the uncompressed data.
+
+     uncompress returns Z_OK if success, Z_MEM_ERROR if there was not
+   enough memory, Z_BUF_ERROR if there was not enough room in the output
+   buffer, or Z_DATA_ERROR if the input data was corrupted or incomplete.  In
+   the case where there is not enough room, uncompress() will fill the output
+   buffer with the uncompressed data up to that point.
+*/
+
+ZEXTERN int ZEXPORT uncompress2(Bytef *dest, uLongf *destLen,
+                                const Bytef *source, uLong *sourceLen);
+ZEXTERN int ZEXPORT uncompress2_z(Bytef *dest, z_size_t *destLen,
+                                  const Bytef *source, z_size_t *sourceLen);
+/*
+     Same as uncompress, except that sourceLen is a pointer, where the
+   length of the source is *sourceLen.  On return, *sourceLen is the number of
+   source bytes consumed.
+*/
+
+                        /* gzip file access functions */
+
+/*
+     This library supports reading and writing files in gzip (.gz) format with
+   an interface similar to that of stdio, using the functions that start with
+   "gz".  The gzip format is different from the zlib format.  gzip is a gzip
+   wrapper, documented in RFC 1952, wrapped around a deflate stream.
+*/
+
+typedef struct gzFile_s *gzFile;    /* semi-opaque gzip file descriptor */
+
+/*
+ZEXTERN gzFile ZEXPORT gzopen(const char *path, const char *mode);
+
+     Open the gzip (.gz) file at path for reading and decompressing, or
+   compressing and writing.  The mode parameter is as in fopen ("rb" or "wb")
+   but can also include a compression level ("wb9") or a strategy: 'f' for
+   filtered data as in "wb6f", 'h' for Huffman-only compression as in "wb1h",
+   'R' for run-length encoding as in "wb1R", or 'F' for fixed code compression
+   as in "wb9F".  (See the description of deflateInit2 for more information
+   about the strategy parameter.)  'T' will request transparent writing or
+   appending with no compression and not using the gzip format. 'T' cannot be
+   used to force transparent reading. Transparent reading is automatically
+   performed if there is no gzip header at the start. Transparent reading can
+   be disabled with the 'G' option, which will instead return an error if there
+   is no gzip header. 'N' will open the file in non-blocking mode.
+
+     'a' can be used instead of 'w' to request that the gzip stream that will
+   be written be appended to the file.  '+' will result in an error, since
+   reading and writing to the same gzip file is not supported.  The addition of
+   'x' when writing will create the file exclusively, which fails if the file
+   already exists.  On systems that support it, the addition of 'e' when
+   reading or writing will set the flag to close the file on an execve() call.
+
+     These functions, as well as gzip, will read and decode a sequence of gzip
+   streams in a file.  The append function of gzopen() can be used to create
+   such a file.  (Also see gzflush() for another way to do this.)  When
+   appending, gzopen does not test whether the file begins with a gzip stream,
+   nor does it look for the end of the gzip streams to begin appending.  gzopen
+   will simply append a gzip stream to the existing file.
+
+     gzopen can be used to read a file which is not in gzip format; in this
+   case gzread will directly read from the file without decompression.  When
+   reading, this will be detected automatically by looking for the magic two-
+   byte gzip header.
+
+     gzopen returns NULL if the file could not be opened, if there was
+   insufficient memory to allocate the gzFile state, or if an invalid mode was
+   specified (an 'r', 'w', or 'a' was not provided, or '+' was provided).
+   errno can be checked to determine if the reason gzopen failed was that the
+   file could not be opened. Note that if 'N' is in mode for non-blocking, the
+   open() itself can fail in order to not block. In that case gzopen() will
+   return NULL and errno will be EAGAIN or ENONBLOCK. The call to gzopen() can
+   then be re-tried. If the application would like to block on opening the
+   file, then it can use open() without O_NONBLOCK, and then gzdopen() with the
+   resulting file descriptor and 'N' in the mode, which will set it to non-
+   blocking.
+*/
+
+ZEXTERN gzFile ZEXPORT gzdopen(int fd, const char *mode);
+/*
+     Associate a gzFile with the file descriptor fd.  File descriptors are
+   obtained from calls like open, dup, creat, pipe or fileno (if the file has
+   been previously opened with fopen).  The mode parameter is as in gzopen. An
+   'e' in mode will set fd's flag to close the file on an execve() call. An 'N'
+   in mode will set fd's non-blocking flag.
+
+     The next call of gzclose on the returned gzFile will also close the file
+   descriptor fd, just like fclose(fdopen(fd, mode)) closes the file descriptor
+   fd.  If you want to keep fd open, use fd = dup(fd_keep); gz = gzdopen(fd,
+   mode);.  The duplicated descriptor should be saved to avoid a leak, since
+   gzdopen does not close fd if it fails.  If you are using fileno() to get the
+   file descriptor from a FILE *, then you will have to use dup() to avoid
+   double-close()ing the file descriptor.  Both gzclose() and fclose() will
+   close the associated file descriptor, so they need to have different file
+   descriptors.
+
+     gzdopen returns NULL if there was insufficient memory to allocate the
+   gzFile state, if an invalid mode was specified (an 'r', 'w', or 'a' was not
+   provided, or '+' was provided), or if fd is -1.  The file descriptor is not
+   used until the next gz* read, write, seek, or close operation, so gzdopen
+   will not detect if fd is invalid (unless fd is -1).
+*/
+
+ZEXTERN int ZEXPORT gzbuffer(gzFile file, unsigned size);
+/*
+     Set the internal buffer size used by this library's functions for file to
+   size.  The default buffer size is 8192 bytes.  This function must be called
+   after gzopen() or gzdopen(), and before any other calls that read or write
+   the file.  The buffer memory allocation is always deferred to the first read
+   or write.  Three times that size in buffer space is allocated.  A larger
+   buffer size of, for example, 64K or 128K bytes will noticeably increase the
+   speed of decompression (reading).
+
+     The new buffer size also affects the maximum length for gzprintf().
+
+     gzbuffer() returns 0 on success, or -1 on failure, such as being called
+   too late.
+*/
+
+ZEXTERN int ZEXPORT gzsetparams(gzFile file, int level, int strategy);
+/*
+     Dynamically update the compression level and strategy for file.  See the
+   description of deflateInit2 for the meaning of these parameters. Previously
+   provided data is flushed before applying the parameter changes.
+
+     gzsetparams returns Z_OK if success, Z_STREAM_ERROR if the file was not
+   opened for writing, Z_ERRNO if there is an error writing the flushed data,
+   or Z_MEM_ERROR if there is a memory allocation error.
+*/
+
+ZEXTERN int ZEXPORT gzread(gzFile file, voidp buf, unsigned len);
+/*
+     Read and decompress up to len uncompressed bytes from file into buf.  If
+   the input file is not in gzip format, gzread copies the given number of
+   bytes into the buffer directly from the file.
+
+     After reaching the end of a gzip stream in the input, gzread will continue
+   to read, looking for another gzip stream.  Any number of gzip streams may be
+   concatenated in the input file, and will all be decompressed by gzread().
+   If something other than a gzip stream is encountered after a gzip stream,
+   that remaining trailing garbage is ignored (and no error is returned).
+
+     gzread can be used to read a gzip file that is being concurrently written.
+   Upon reaching the end of the input, gzread will return with the available
+   data.  If the error code returned by gzerror is Z_OK or Z_BUF_ERROR, then
+   gzclearerr can be used to clear the end of file indicator in order to permit
+   gzread to be tried again.  Z_OK indicates that a gzip stream was completed
+   on the last gzread.  Z_BUF_ERROR indicates that the input file ended in the
+   middle of a gzip stream.  Note that gzread does not return -1 in the event
+   of an incomplete gzip stream.  This error is deferred until gzclose(), which
+   will return Z_BUF_ERROR if the last gzread ended in the middle of a gzip
+   stream.  Alternatively, gzerror can be used before gzclose to detect this
+   case.
+
+     gzread can be used to read a gzip file on a non-blocking device. If the
+   input stalls and there is no uncompressed data to return, then gzread() will
+   return -1, and errno will be EAGAIN or EWOULDBLOCK. gzread() can then be
+   called again.
+
+     gzread returns the number of uncompressed bytes actually read, less than
+   len for end of file, or -1 for error.  If len is too large to fit in an int,
+   then nothing is read, -1 is returned, and the error state is set to
+   Z_STREAM_ERROR. If some data was read before an error, then that data is
+   returned until exhausted, after which the next call will signal the error.
+*/
+
+ZEXTERN z_size_t ZEXPORT gzfread(voidp buf, z_size_t size, z_size_t nitems,
+                                 gzFile file);
+/*
+     Read and decompress up to nitems items of size size from file into buf,
+   otherwise operating as gzread() does.  This duplicates the interface of
+   stdio's fread(), with size_t request and return types.  If the library
+   defines size_t, then z_size_t is identical to size_t.  If not, then z_size_t
+   is an unsigned integer type that can contain a pointer.
+
+     gzfread() returns the number of full items read of size size, or zero if
+   the end of the file was reached and a full item could not be read, or if
+   there was an error.  gzerror() must be consulted if zero is returned in
+   order to determine if there was an error.  If the multiplication of size and
+   nitems overflows, i.e. the product does not fit in a z_size_t, then nothing
+   is read, zero is returned, and the error state is set to Z_STREAM_ERROR.
+
+     In the event that the end of file is reached and only a partial item is
+   available at the end, i.e. the remaining uncompressed data length is not a
+   multiple of size, then the final partial item is nevertheless read into buf
+   and the end-of-file flag is set.  The length of the partial item read is not
+   provided, but could be inferred from the result of gztell().  This behavior
+   is the same as that of fread() implementations in common libraries. This
+   could result in data loss if used with size != 1 when reading a concurrently
+   written file or a non-blocking file. In that case, use size == 1 or gzread()
+   instead.
+*/
+
+ZEXTERN int ZEXPORT gzwrite(gzFile file, voidpc buf, unsigned len);
+/*
+     Compress and write the len uncompressed bytes at buf to file. gzwrite
+   returns the number of uncompressed bytes written, or 0 in case of error or
+   if len is 0.  If the write destination is non-blocking, then gzwrite() may
+   return a number of bytes written that is not 0 and less than len.
+
+     If len does not fit in an int, then 0 is returned and nothing is written.
+*/
+
+ZEXTERN z_size_t ZEXPORT gzfwrite(voidpc buf, z_size_t size,
+                                  z_size_t nitems, gzFile file);
+/*
+     Compress and write nitems items of size size from buf to file, duplicating
+   the interface of stdio's fwrite(), with size_t request and return types.  If
+   the library defines size_t, then z_size_t is identical to size_t.  If not,
+   then z_size_t is an unsigned integer type that can contain a pointer.
+
+     gzfwrite() returns the number of full items written of size size, or zero
+   if there was an error.  If the multiplication of size and nitems overflows,
+   i.e. the product does not fit in a z_size_t, then nothing is written, zero
+   is returned, and the error state is set to Z_STREAM_ERROR.
+
+     If writing a concurrently read file or a non-blocking file with size != 1,
+   a partial item could be written, with no way of knowing how much of it was
+   not written, resulting in data loss.  In that case, use size == 1 or
+   gzwrite() instead.
+*/
+
+#if defined(STDC) || defined(Z_HAVE_STDARG_H)
+ZEXTERN int ZEXPORTVA gzprintf(gzFile file, const char *format, ...);
+#else
+ZEXTERN int ZEXPORTVA gzprintf();
+#endif
+/*
+     Convert, format, compress, and write the arguments (...) to file under
+   control of the string format, as in fprintf.  gzprintf returns the number of
+   uncompressed bytes actually written, or a negative zlib error code in case
+   of error.  The number of uncompressed bytes written is limited to 8191, or
+   one less than the buffer size given to gzbuffer().  The caller should assure
+   that this limit is not exceeded.  If it is exceeded, then gzprintf() will
+   return an error (0) with nothing written.
+
+     In that last case, there may also be a buffer overflow with unpredictable
+   consequences, which is possible only if zlib was compiled with the insecure
+   functions sprintf() or vsprintf(), because the secure snprintf() and
+   vsnprintf() functions were not available. That would only be the case for
+   a non-ANSI C compiler. zlib may have been built without gzprintf() because
+   secure functions were not available and having gzprintf() be insecure was
+   not an option, in which case, gzprintf() returns Z_STREAM_ERROR. All of
+   these possibilities can be determined using zlibCompileFlags().
+
+     If a Z_BUF_ERROR is returned, then nothing was written due to a stall on
+   the non-blocking write destination.
+*/
+
+ZEXTERN int ZEXPORT gzputs(gzFile file, const char *s);
+/*
+     Compress and write the given null-terminated string s to file, excluding
+   the terminating null character.
+
+     gzputs returns the number of characters written, or -1 in case of error.
+   The number of characters written may be less than the length of the string
+   if the write destination is non-blocking.
+
+     If the length of the string does not fit in an int, then -1 is returned
+   and nothing is written.
+*/
+
+ZEXTERN char * ZEXPORT gzgets(gzFile file, char *buf, int len);
+/*
+     Read and decompress bytes from file into buf, until len-1 characters are
+   read, or until a newline character is read and transferred to buf, or an
+   end-of-file condition is encountered.  If any characters are read or if len
+   is one, the string is terminated with a null character.  If no characters
+   are read due to an end-of-file or len is less than one, then the buffer is
+   left untouched.
+
+     gzgets returns buf which is a null-terminated string, or it returns NULL
+   for end-of-file or in case of error. If some data was read before an error,
+   then that data is returned until exhausted, after which the next call will
+   return NULL to signal the error.
+
+     gzgets can be used on a file being concurrently written, and on a non-
+   blocking device, both as for gzread(). However lines may be broken in the
+   middle, leaving it up to the application to reassemble them as needed.
+*/
+
+ZEXTERN int ZEXPORT gzputc(gzFile file, int c);
+/*
+     Compress and write c, converted to an unsigned char, into file.  gzputc
+   returns the value that was written, or -1 in case of error.
+*/
+
+ZEXTERN int ZEXPORT gzgetc(gzFile file);
+/*
+     Read and decompress one byte from file. gzgetc returns this byte or -1 in
+   case of end of file or error. If some data was read before an error, then
+   that data is returned until exhausted, after which the next call will return
+   -1 to signal the error.
+
+     This is implemented as a macro for speed. As such, it does not do all of
+   the checking the other functions do. I.e. it does not check to see if file
+   is NULL, nor whether the structure file points to has been clobbered or not.
+
+     gzgetc can be used to read a gzip file on a non-blocking device. If the
+   input stalls and there is no uncompressed data to return, then gzgetc() will
+   return -1, and errno will be EAGAIN or EWOULDBLOCK. gzread() can then be
+   called again.
+*/
+
+ZEXTERN int ZEXPORT gzungetc(int c, gzFile file);
+/*
+     Push c back onto the stream for file to be read as the first character on
+   the next read.  At least one character of push-back is always allowed.
+   gzungetc() returns the character pushed, or -1 on failure.  gzungetc() will
+   fail if c is -1, and may fail if a character has been pushed but not read
+   yet.  If gzungetc is used immediately after gzopen or gzdopen, at least the
+   output buffer size of pushed characters is allowed.  (See gzbuffer above.)
+   The pushed character will be discarded if the stream is repositioned with
+   gzseek() or gzrewind().
+
+     gzungetc(-1, file) will force any pending seek to execute. Then gztell()
+   will report the position, even if the requested seek reached end of file.
+   This can be used to determine the number of uncompressed bytes in a gzip
+   file without having to read it into a buffer.
+*/
+
+ZEXTERN int ZEXPORT gzflush(gzFile file, int flush);
+/*
+     Flush all pending output to file.  The parameter flush is as in the
+   deflate() function.  The return value is the zlib error number (see function
+   gzerror below).  gzflush is only permitted when writing.
+
+     If the flush parameter is Z_FINISH, the remaining data is written and the
+   gzip stream is completed in the output.  If gzwrite() is called again, a new
+   gzip stream will be started in the output.  gzread() is able to read such
+   concatenated gzip streams.
+
+     gzflush should be called only when strictly necessary because it will
+   degrade compression if called too often.
+*/
+
+/*
+ZEXTERN z_off_t ZEXPORT gzseek(gzFile file,
+                               z_off_t offset, int whence);
+
+     Set the starting position to offset relative to whence for the next gzread
+   or gzwrite on file.  The offset represents a number of bytes in the
+   uncompressed data stream.  The whence parameter is defined as in lseek(2);
+   the value SEEK_END is not supported.
+
+     If the file is opened for reading, this function is emulated but can be
+   extremely slow.  If the file is opened for writing, only forward seeks are
+   supported; gzseek then compresses a sequence of zeroes up to the new
+   starting position. For reading or writing, any actual seeking is deferred
+   until the next read or write operation, or close operation when writing.
+
+     gzseek returns the resulting offset location as measured in bytes from
+   the beginning of the uncompressed stream, or -1 in case of error, in
+   particular if the file is opened for writing and the new starting position
+   would be before the current position.
+*/
+
+ZEXTERN int ZEXPORT gzrewind(gzFile file);
+/*
+     Rewind file. This function is supported only for reading.
+
+     gzrewind(file) is equivalent to (int)gzseek(file, 0L, SEEK_SET).
+*/
+
+/*
+ZEXTERN z_off_t ZEXPORT gztell(gzFile file);
+
+     Return the starting position for the next gzread or gzwrite on file.
+   This position represents a number of bytes in the uncompressed data stream,
+   and is zero when starting, even if appending or reading a gzip stream from
+   the middle of a file using gzdopen().
+
+     gztell(file) is equivalent to gzseek(file, 0L, SEEK_CUR)
+*/
+
+/*
+ZEXTERN z_off_t ZEXPORT gzoffset(gzFile file);
+
+     Return the current compressed (actual) read or write offset of file.  This
+   offset includes the count of bytes that precede the gzip stream, for example
+   when appending or when using gzdopen() for reading.  When reading, the
+   offset does not include as yet unused buffered input.  This information can
+   be used for a progress indicator.  On error, gzoffset() returns -1.
+*/
+
+ZEXTERN int ZEXPORT gzeof(gzFile file);
+/*
+     Return true (1) if the end-of-file indicator for file has been set while
+   reading, false (0) otherwise.  Note that the end-of-file indicator is set
+   only if the read tried to go past the end of the input, but came up short.
+   Therefore, just like feof(), gzeof() may return false even if there is no
+   more data to read, in the event that the last read request was for the exact
+   number of bytes remaining in the input file.  This will happen if the input
+   file size is an exact multiple of the buffer size.
+
+     If gzeof() returns true, then the read functions will return no more data,
+   unless the end-of-file indicator is reset by gzclearerr() and the input file
+   has grown since the previous end of file was detected.
+*/
+
+ZEXTERN int ZEXPORT gzdirect(gzFile file);
+/*
+     Return true (1) if file is being copied directly while reading, or false
+   (0) if file is a gzip stream being decompressed.
+
+     If the input file is empty, gzdirect() will return true, since the input
+   does not contain a gzip stream.
+
+     If gzdirect() is used immediately after gzopen() or gzdopen() it will
+   cause buffers to be allocated to allow reading the file to determine if it
+   is a gzip file. Therefore if gzbuffer() is used, it should be called before
+   gzdirect(). If the input is being written concurrently or the device is non-
+   blocking, then gzdirect() may give a different answer once four bytes of
+   input have been accumulated, which is what is needed to confirm or deny a
+   gzip header. Before this, gzdirect() will return true (1).
+
+     When writing, gzdirect() returns true (1) if transparent writing was
+   requested ("wT" for the gzopen() mode), or false (0) otherwise.  (Note:
+   gzdirect() is not needed when writing.  Transparent writing must be
+   explicitly requested, so the application already knows the answer.  When
+   linking statically, using gzdirect() will include all of the zlib code for
+   gzip file reading and decompression, which may not be desired.)
+*/
+
+ZEXTERN int ZEXPORT gzclose(gzFile file);
+/*
+     Flush all pending output for file, if necessary, close file and
+   deallocate the (de)compression state.  Note that once file is closed, you
+   cannot call gzerror with file, since its structures have been deallocated.
+   gzclose must not be called more than once on the same file, just as free
+   must not be called more than once on the same allocation.
+
+     gzclose will return Z_STREAM_ERROR if file is not valid, Z_ERRNO on a
+   file operation error, Z_MEM_ERROR if out of memory, Z_BUF_ERROR if the
+   last read ended in the middle of a gzip stream, or Z_OK on success.
+*/
+
+ZEXTERN int ZEXPORT gzclose_r(gzFile file);
+ZEXTERN int ZEXPORT gzclose_w(gzFile file);
+/*
+     Same as gzclose(), but gzclose_r() is only for use when reading, and
+   gzclose_w() is only for use when writing or appending.  The advantage to
+   using these instead of gzclose() is that they avoid linking in zlib
+   compression or decompression code that is not used when only reading or only
+   writing respectively.  If gzclose() is used, then both compression and
+   decompression code will be included the application when linking to a static
+   zlib library.
+*/
+
+ZEXTERN const char * ZEXPORT gzerror(gzFile file, int *errnum);
+/*
+     Return the error message for the last error which occurred on file.
+   If errnum is not NULL, *errnum is set to zlib error number.  If an error
+   occurred in the file system and not in the compression library, *errnum is
+   set to Z_ERRNO and the application may consult errno to get the exact error
+   code.
+
+     The application must not modify the returned string.  Future calls to
+   this function may invalidate the previously returned string.  If file is
+   closed, then the string previously returned by gzerror will no longer be
+   available.
+
+     gzerror() should be used to distinguish errors from end-of-file for those
+   functions above that do not distinguish those cases in their return values.
+*/
+
+ZEXTERN void ZEXPORT gzclearerr(gzFile file);
+/*
+     Clear the error and end-of-file flags for file.  This is analogous to the
+   clearerr() function in stdio.  This is useful for continuing to read a gzip
+   file that is being written concurrently.
+*/
+
+#endif /* !Z_SOLO */
+
+                        /* checksum functions */
+
+/*
+     These functions are not related to compression but are exported
+   anyway because they might be useful in applications using the compression
+   library.
+*/
+
+ZEXTERN uLong ZEXPORT adler32(uLong adler, const Bytef *buf, uInt len);
+/*
+     Update a running Adler-32 checksum with the bytes buf[0..len-1] and
+   return the updated checksum. An Adler-32 value is in the range of a 32-bit
+   unsigned integer. If buf is Z_NULL, this function returns the required
+   initial value for the checksum.
+
+     An Adler-32 checksum is almost as reliable as a CRC-32 but can be computed
+   much faster.
+
+   Usage example:
+
+     uLong adler = adler32(0L, Z_NULL, 0);
+
+     while (read_buffer(buffer, length) != EOF) {
+       adler = adler32(adler, buffer, length);
+     }
+     if (adler != original_adler) error();
+*/
+
+ZEXTERN uLong ZEXPORT adler32_z(uLong adler, const Bytef *buf,
+                                z_size_t len);
+/*
+     Same as adler32(), but with a size_t length.  Note that a long is 32 bits
+   on Windows.
+*/
+
+/*
+ZEXTERN uLong ZEXPORT adler32_combine(uLong adler1, uLong adler2,
+                                      z_off_t len2);
+
+     Combine two Adler-32 checksums into one.  For two sequences of bytes, seq1
+   and seq2 with lengths len1 and len2, Adler-32 checksums were calculated for
+   each, adler1 and adler2.  adler32_combine() returns the Adler-32 checksum of
+   seq1 and seq2 concatenated, requiring only adler1, adler2, and len2.  Note
+   that the z_off_t type (like off_t) is a signed integer.  If len2 is
+   negative, the result has no meaning or utility.
+*/
+
+ZEXTERN uLong ZEXPORT crc32(uLong crc, const Bytef *buf, uInt len);
+/*
+     Update a running CRC-32 with the bytes buf[0..len-1] and return the
+   updated CRC-32. A CRC-32 value is in the range of a 32-bit unsigned integer.
+   If buf is Z_NULL, this function returns the required initial value for the
+   crc. Pre- and post-conditioning (one's complement) is performed within this
+   function so it shouldn't be done by the application.
+
+   Usage example:
+
+     uLong crc = crc32(0L, Z_NULL, 0);
+
+     while (read_buffer(buffer, length) != EOF) {
+       crc = crc32(crc, buffer, length);
+     }
+     if (crc != original_crc) error();
+*/
+
+ZEXTERN uLong ZEXPORT crc32_z(uLong crc, const Bytef *buf,
+                              z_size_t len);
+/*
+     Same as crc32(), but with a size_t length.  Note that a long is 32 bits on
+   Windows.
+*/
+
+/*
+ZEXTERN uLong ZEXPORT crc32_combine(uLong crc1, uLong crc2, z_off_t len2);
+
+     Combine two CRC-32 check values into one.  For two sequences of bytes,
+   seq1 and seq2 with lengths len1 and len2, CRC-32 check values were
+   calculated for each, crc1 and crc2.  crc32_combine() returns the CRC-32
+   check value of seq1 and seq2 concatenated, requiring only crc1, crc2, and
+   len2. len2 must be non-negative, otherwise zero is returned.
+*/
+
+/*
+ZEXTERN uLong ZEXPORT crc32_combine_gen(z_off_t len2);
+
+     Return the operator corresponding to length len2, to be used with
+   crc32_combine_op(). len2 must be non-negative, otherwise zero is returned.
+*/
+
+ZEXTERN uLong ZEXPORT crc32_combine_op(uLong crc1, uLong crc2, uLong op);
+/*
+     Give the same result as crc32_combine(), using op in place of len2. op is
+   is generated from len2 by crc32_combine_gen(). This will be faster than
+   crc32_combine() if the generated op is used more than once.
+*/
+
+
+                        /* various hacks, don't look :) */
+
+/* deflateInit and inflateInit are macros to allow checking the zlib version
+ * and the compiler's view of z_stream:
+ */
+ZEXTERN int ZEXPORT deflateInit_(z_streamp strm, int level,
+                                 const char *version, int stream_size);
+ZEXTERN int ZEXPORT inflateInit_(z_streamp strm,
+                                 const char *version, int stream_size);
+ZEXTERN int ZEXPORT deflateInit2_(z_streamp strm, int  level, int  method,
+                                  int windowBits, int memLevel,
+                                  int strategy, const char *version,
+                                  int stream_size);
+ZEXTERN int ZEXPORT inflateInit2_(z_streamp strm, int  windowBits,
+                                  const char *version, int stream_size);
+ZEXTERN int ZEXPORT inflateBackInit_(z_streamp strm, int windowBits,
+                                     unsigned char FAR *window,
+                                     const char *version,
+                                     int stream_size);
+#ifdef Z_PREFIX_SET
+#  define z_deflateInit(strm, level) \
+          deflateInit_((strm), (level), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define z_inflateInit(strm) \
+          inflateInit_((strm), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define z_deflateInit2(strm, level, method, windowBits, memLevel, strategy) \
+          deflateInit2_((strm),(level),(method),(windowBits),(memLevel),\
+                        (strategy), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define z_inflateInit2(strm, windowBits) \
+          inflateInit2_((strm), (windowBits), ZLIB_VERSION, \
+                        (int)sizeof(z_stream))
+#  define z_inflateBackInit(strm, windowBits, window) \
+          inflateBackInit_((strm), (windowBits), (window), \
+                           ZLIB_VERSION, (int)sizeof(z_stream))
+#else
+#  define deflateInit(strm, level) \
+          deflateInit_((strm), (level), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define inflateInit(strm) \
+          inflateInit_((strm), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define deflateInit2(strm, level, method, windowBits, memLevel, strategy) \
+          deflateInit2_((strm),(level),(method),(windowBits),(memLevel),\
+                        (strategy), ZLIB_VERSION, (int)sizeof(z_stream))
+#  define inflateInit2(strm, windowBits) \
+          inflateInit2_((strm), (windowBits), ZLIB_VERSION, \
+                        (int)sizeof(z_stream))
+#  define inflateBackInit(strm, windowBits, window) \
+          inflateBackInit_((strm), (windowBits), (window), \
+                           ZLIB_VERSION, (int)sizeof(z_stream))
+#endif
+
+#ifndef Z_SOLO
+
+/* gzgetc() macro and its supporting function and exposed data structure.  Note
+ * that the real internal state is much larger than the exposed structure.
+ * This abbreviated structure exposes just enough for the gzgetc() macro.  The
+ * user should not mess with these exposed elements, since their names or
+ * behavior could change in the future, perhaps even capriciously.  They can
+ * only be used by the gzgetc() macro.  You have been warned.
+ */
+struct gzFile_s {
+    unsigned have;
+    unsigned char *next;
+    z_off64_t pos;
+};
+ZEXTERN int ZEXPORT gzgetc_(gzFile file);       /* backward compatibility */
+#ifdef Z_PREFIX_SET
+#  undef z_gzgetc
+#  define z_gzgetc(g) \
+          ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : (gzgetc)(g))
+#else
+#  define gzgetc(g) \
+          ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : (gzgetc)(g))
+#endif
+
+/* provide 64-bit offset functions if _LARGEFILE64_SOURCE defined, and/or
+ * change the regular functions to 64 bits if _FILE_OFFSET_BITS is 64 (if
+ * both are true, the application gets the *64 functions, and the regular
+ * functions are changed to 64 bits) -- in case these are set on systems
+ * without large file support, _LFS64_LARGEFILE must also be true
+ */
+#ifdef Z_LARGE64
+   ZEXTERN gzFile ZEXPORT gzopen64(const char *, const char *);
+   ZEXTERN z_off64_t ZEXPORT gzseek64(gzFile, z_off64_t, int);
+   ZEXTERN z_off64_t ZEXPORT gztell64(gzFile);
+   ZEXTERN z_off64_t ZEXPORT gzoffset64(gzFile);
+   ZEXTERN uLong ZEXPORT adler32_combine64(uLong, uLong, z_off64_t);
+   ZEXTERN uLong ZEXPORT crc32_combine64(uLong, uLong, z_off64_t);
+   ZEXTERN uLong ZEXPORT crc32_combine_gen64(z_off64_t);
+#endif
+
+#if !defined(ZLIB_INTERNAL) && defined(Z_WANT64)
+#  ifdef Z_PREFIX_SET
+#    define z_gzopen z_gzopen64
+#    define z_gzseek z_gzseek64
+#    define z_gztell z_gztell64
+#    define z_gzoffset z_gzoffset64
+#    define z_adler32_combine z_adler32_combine64
+#    define z_crc32_combine z_crc32_combine64
+#    define z_crc32_combine_gen z_crc32_combine_gen64
+#  else
+#    define gzopen gzopen64
+#    define gzseek gzseek64
+#    define gztell gztell64
+#    define gzoffset gzoffset64
+#    define adler32_combine adler32_combine64
+#    define crc32_combine crc32_combine64
+#    define crc32_combine_gen crc32_combine_gen64
+#  endif
+#  ifndef Z_LARGE64
+     ZEXTERN gzFile ZEXPORT gzopen64(const char *, const char *);
+     ZEXTERN z_off_t ZEXPORT gzseek64(gzFile, z_off_t, int);
+     ZEXTERN z_off_t ZEXPORT gztell64(gzFile);
+     ZEXTERN z_off_t ZEXPORT gzoffset64(gzFile);
+     ZEXTERN uLong ZEXPORT adler32_combine64(uLong, uLong, z_off64_t);
+     ZEXTERN uLong ZEXPORT crc32_combine64(uLong, uLong, z_off64_t);
+     ZEXTERN uLong ZEXPORT crc32_combine_gen64(z_off64_t);
+#  endif
+#else
+   ZEXTERN gzFile ZEXPORT gzopen(const char *, const char *);
+   ZEXTERN z_off_t ZEXPORT gzseek(gzFile, z_off_t, int);
+   ZEXTERN z_off_t ZEXPORT gztell(gzFile);
+   ZEXTERN z_off_t ZEXPORT gzoffset(gzFile);
+   ZEXTERN uLong ZEXPORT adler32_combine(uLong, uLong, z_off_t);
+   ZEXTERN uLong ZEXPORT crc32_combine(uLong, uLong, z_off_t);
+   ZEXTERN uLong ZEXPORT crc32_combine_gen(z_off_t);
+#endif
+
+#else /* Z_SOLO */
+
+   ZEXTERN uLong ZEXPORT adler32_combine(uLong, uLong, z_off_t);
+   ZEXTERN uLong ZEXPORT crc32_combine(uLong, uLong, z_off_t);
+   ZEXTERN uLong ZEXPORT crc32_combine_gen(z_off_t);
+
+#endif /* !Z_SOLO */
+
+/* undocumented functions */
+ZEXTERN const char   * ZEXPORT zError(int);
+ZEXTERN int            ZEXPORT inflateSyncPoint(z_streamp);
+ZEXTERN const z_crc_t FAR * ZEXPORT get_crc_table(void);
+ZEXTERN int            ZEXPORT inflateUndermine(z_streamp, int);
+ZEXTERN int            ZEXPORT inflateValidate(z_streamp, int);
+ZEXTERN unsigned long  ZEXPORT inflateCodesUsed(z_streamp);
+ZEXTERN int            ZEXPORT inflateResetKeep(z_streamp);
+ZEXTERN int            ZEXPORT deflateResetKeep(z_streamp);
+#if defined(_WIN32) && !defined(Z_SOLO)
+ZEXTERN gzFile         ZEXPORT gzopen_w(const wchar_t *path,
+                                        const char *mode);
+#endif
+#if defined(STDC) || defined(Z_HAVE_STDARG_H)
+#  ifndef Z_SOLO
+ZEXTERN int            ZEXPORTVA gzvprintf(gzFile file,
+                                           const char *format,
+                                           va_list va);
+#  endif
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* ZLIB_H */