@zwave-js/config 8.8.3 → 8.9.0-beta.0

package/config/devices/0x0002/010101.json

@@ -28,5 +28,10 @@
 			["Battery", "get"],
 			["Thermostat Setpoint", "get", 1]
 		]
+	},
+	"metadata": {
+		"inclusion": "• Ensure smart radiator valve is factory reset. \n• Activate “Inclusion” on the Z-Wave controller. \n• Quickly press and release menu button (one with a dot) on smart radiator valve. \n• Observe both controller and smart radiator valve for status of the process.",
+		"exclusion": "• Activate “Exclusion” on the Z-Wave controller. \n• Quickly press and release menu button (one with a dot) on smart radiator valve. \n• Observe both controller and smart radiator valve for status of the process.",
+		"reset": "Remove the battery cover and take out one battery. \nPress and hold menu button (one with a dot) for approx. 5 seconds, while re-inserting the battery. \nSmart radiator valve is now factory reset and in mounting mode."
 	}
 }

package/config/devices/0x0002/keemple_smart_radiator.json

@@ -4,6 +4,10 @@
 	"label": "Keemple smart radiator",
 	"description": "Electronic radiator thermostat, intended for use with water based room radiators.",
 	"devices": [
+		{
+			"productType": "0x5fff",
+			"productId": "0xa010"
+		},
 		{
 			"productType": "0x6fff",
 			"productId": "0xa010"
@@ -12,5 +16,10 @@
 	"firmwareVersion": {
 		"min": "0.0",
 		"max": "255.255"
+	},
+	"metadata": {
+		"inclusion": "• Ensure smart radiator valve is factory reset. \n• Activate “Inclusion” on the Z-Wave controller. \n• Quickly press and release menu button (one with a dot) on smart radiator valve. \n• Observe both controller and smart radiator valve for status of the process.",
+		"exclusion": "• Activate “Exclusion” on the Z-Wave controller. \n• Quickly press and release menu button (one with a dot) on smart radiator valve. \n• Observe both controller and smart radiator valve for status of the process.",
+		"reset": "Remove the battery cover and take out one battery. \nPress and hold menu button (one with a dot) for approx. 5 seconds, while re-inserting the battery. \nSmart radiator valve is now factory reset and in mounting mode."
 	}
 }

package/config/devices/0x0005/{pe653_3.4-3.4.json → pe653.json}

@@ -10,16 +10,16 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "3.4",
-		"max": "3.4"
+		"min": "0.0",
+		"max": "255.255"
 	},
 	"paramInformation": [
 		{
 			"#": "2",
 			"label": "Fireman Timeout",
 			"description": "Minutes that pump will continue to run after heater shutoff",
-			"unit": "Minutes",
 			"valueSize": 1,
+			"unit": "minutes",
 			"minValue": 0,
 			"maxValue": 255,
 			"defaultValue": 0,
@@ -29,8 +29,8 @@
 			"#": "22",
 			"label": "Pool - Spa Mode",
 			"description": "Controller Mode",
-			"unit": "Decimal",
 			"valueSize": 1,
+			"unit": "Decimal",
 			"minValue": 0,
 			"maxValue": 2,
 			"defaultValue": 0
@@ -39,8 +39,8 @@
 			"#": "1[0xff]",
 			"label": "Booster/Cleaner Pump Operation Mode",
 			"description": "Which circuit the booster/cleaner pump resides on",
-			"unit": "Decimal",
 			"valueSize": 2,
+			"unit": "Decimal",
 			"minValue": 1,
 			"maxValue": 6,
 			"defaultValue": 1
@@ -49,8 +49,8 @@
 			"#": "1[0xff00]",
 			"label": "Pump Type Operation Mode",
 			"description": "Which type of pump is being used",
-			"unit": "Decimal",
 			"valueSize": 2,
+			"unit": "Decimal",
 			"minValue": 0,
 			"maxValue": 7,
 			"defaultValue": 0

package/config/devices/0x000c/hs-wx300.json

@@ -7,6 +7,10 @@
 		{
 			"productType": "0x4447",
 			"productId": "0x4037"
+		},
+		{
+			"productType": "0x4447",
+			"productId": "0x4036"
 		}
 	],
 	"firmwareVersion": {
@@ -185,5 +189,11 @@
 				}
 			]
 		}
-	]
+	],
+	"metadata": {
+		"inclusion": "1. Put your Z-Wave controller into inclusion (or exclusion) mode. Consult your controller’s manual if you’re unsure how to do this. \n2. In rapid succession, tap the bottom paddle 2 times, then press & hold the bottom paddle for 3 seconds (tap-tap-press & hold). This will initiate the inclusion (or exclusion) process. \nNote: The switch will default to dimmer mode after Z-Wave exclusion.",
+		"exclusion": "1. Put your Z-Wave controller into inclusion (or exclusion) mode. Consult your controller’s manual if you’re unsure how to do this. \n2. In rapid succession, tap the bottom paddle 2 times, then press & hold the bottom paddle for 3 seconds (tap-tap-press & hold). This will initiate the inclusion (or exclusion) process. \nNote: The switch will default to dimmer mode after Z-Wave exclusion.",
+		"reset": "In rapid succession, tap the top paddle 3 times, then tap the bottom paddle 3 times. If all LEDs flash white 5 times, factory reset was successful. If not, repeat this procedure. \nNote: As this must be done very quickly, we recommend using 2 fingers for this operation; one on each paddle! \nNote: The switch will default to 3-wire mode and dimmer mode after factory reset.",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/4176/HSPRODKB-HS-WX300UserGuide-260421-1500-2688%20-%20Copy.pdf"
+	}
 }

package/config/devices/0x001a/{rf9537_0.0-3.4.json → rf9537.json}

@@ -12,7 +12,7 @@
 	],
 	"firmwareVersion": {
 		"min": "0.0",
-		"max": "3.4"
+		"max": "255.255"
 	},
 	"associations": {
 		"1": {

package/config/devices/0x004f/{fxa-0404_5.0-8.0.json → fxa-0404.json}

@@ -10,8 +10,8 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "5.0",
-		"max": "8.0"
+		"min": "0.0",
+		"max": "255.255"
 	},
 	"paramInformation": [
 		{

package/config/devices/0x0063/55251_zw3107.json

@@ -79,7 +79,7 @@
 		},
 		{
 			"#": "9",
-			"label": "Dime Rate Steps (Manual)",
+			"label": "Dim Rate Steps (Manual)",
 			"description": "Number of steps or levels",
 			"valueSize": 1,
 			"minValue": 1,

package/config/devices/0x0063/55252_zw3105.json

@@ -79,7 +79,7 @@
 		},
 		{
 			"#": "9",
-			"label": "Dime Rate Steps (Manual)",
+			"label": "Dim Rate Steps (Manual)",
 			"description": "Number of steps or levels",
 			"valueSize": 1,
 			"minValue": 1,

package/config/devices/0x0063/{ge_28175_zw3106_5.23-5.23.json → ge_28175_zw3106.json}

@@ -10,8 +10,8 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "5.23",
-		"max": "5.23"
+		"min": "0.0",
+		"max": "255.255"
 	},
 	"paramInformation": [
 		{

package/config/devices/0x0077/{smartdimmer_1.0.json → smartdimmer.json}

@@ -14,7 +14,7 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "1.0",
+		"min": "0.0",
 		"max": "255.255"
 	},
 	"associations": {

package/config/devices/0x0085/{arz_1_1_1.1.json → arz_1_1.json}

@@ -10,7 +10,7 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "1.1",
+		"min": "0.0",
 		"max": "255.255"
 	},
 	"paramInformation": [

package/config/devices/0x0085/zws12.json

@@ -2,21 +2,28 @@
 	"manufacturer": "Fakro",
 	"manufacturerId": "0x0085",
 	"label": "ZWS12",
-	"description": "Chain actuator - window opener (2019)",
+	"description": "Chain Actuator",
 	"devices": [
 		{
 			"productType": "0x0002",
-			"productId": "0x0010"
+			"productId": "0x0001"
 		},
 		{
-			"productType": "0x0002",
-			"productId": "0x0100"
+			"productType": "0x0011",
+			"productId": "0x0001"
 		}
 	],
 	"firmwareVersion": {
 		"min": "0.0",
 		"max": "255.255"
 	},
+	"associations": {
+		"1": {
+			"label": "Basic",
+			"maxNodes": 5,
+			"isLifeline": true
+		}
+	},
 	"paramInformation": [
 		{
 			"#": "7",

package/config/devices/0x008b/{zw111_0.0-2.2.json → zw111.json}

@@ -19,7 +19,7 @@
 	],
 	"firmwareVersion": {
 		"min": "0.0",
-		"max": "2.2"
+		"max": "255.255"
 	},
 	"paramInformation": [
 		{
@@ -205,8 +205,8 @@
 			"#": "92",
 			"label": "Set the threshold value of percent power",
 			"description": "Threshold change in wattage (in terms of percentage)",
-			"unit": "W",
 			"valueSize": 1,
+			"unit": "W",
 			"minValue": 0,
 			"maxValue": 100,
 			"defaultValue": 5

package/config/devices/0x0096/{nq-9121_0.0-2.255.json → nq-9121.json}

@@ -11,11 +11,12 @@
 	],
 	"firmwareVersion": {
 		"min": "0.0",
-		"max": "2.255"
+		"max": "255.255"
 	},
 	"paramInformation": [
 		{
 			"#": "1",
+			"$if": "firmwareVersion <= 2.255",
 			"label": "Pulse factor",
 			"description": "How many pulses * 10 per kWh",
 			"valueSize": 4,
@@ -23,8 +24,19 @@
 			"maxValue": 65535,
 			"defaultValue": 10000
 		},
+		{
+			"#": "1",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Pulse factor",
+			"description": "Impulse or Rotation factor (see NorthQ docs for Gas meters)",
+			"valueSize": 4,
+			"minValue": 0,
+			"maxValue": 1000000,
+			"defaultValue": 1000
+		},
 		{
 			"#": "2",
+			"$if": "firmwareVersion <= 2.255",
 			"label": "Sensor type",
 			"valueSize": 1,
 			"minValue": 0,
@@ -43,6 +55,27 @@
 				}
 			]
 		},
+		{
+			"#": "2",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Sensor type",
+			"description": "Defines the type of sensor",
+			"valueSize": 1,
+			"minValue": 1,
+			"maxValue": 2,
+			"defaultValue": 2,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "magnetic contact",
+					"value": 1
+				},
+				{
+					"label": "silver spot meter",
+					"value": 2
+				}
+			]
+		},
 		{
 			"#": "3",
 			"label": "IR Listen period",
@@ -100,6 +133,7 @@
 		},
 		{
 			"#": "9",
+			"$if": "firmwareVersion <= 2.255",
 			"label": "Pulse count",
 			"description": "Current pulse count in device (pulse count / pulse factor = kWh)",
 			"valueSize": 4,
@@ -107,8 +141,19 @@
 			"maxValue": 50,
 			"defaultValue": 20
 		},
+		{
+			"#": "9",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Pulse count",
+			"description": "This register holds the total number of pulses.",
+			"valueSize": 4,
+			"minValue": 0,
+			"maxValue": 2147483647,
+			"defaultValue": 0
+		},
 		{
 			"#": "10",
+			"$if": "firmwareVersion <= 2.255",
 			"label": "Keep alive period",
 			"description": "How many ticks before going back to sleep in normal wakeup mode.",
 			"valueSize": 2,
@@ -116,6 +161,16 @@
 			"maxValue": 32767,
 			"defaultValue": 60
 		},
+		{
+			"#": "10",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Keep alive period",
+			"description": "How many ticks before going back to sleep in normal wakeup mode.",
+			"valueSize": 2,
+			"minValue": 0,
+			"maxValue": 32767,
+			"defaultValue": 5
+		},
 		{
 			"#": "11",
 			"label": "Real-time mode",
@@ -125,6 +180,17 @@
 			"maxValue": 32767,
 			"defaultValue": 0
 		},
+		{
+			"#": "12",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Serial number",
+			"description": "Read-only serial number in decimal",
+			"valueSize": 4,
+			"minValue": 0,
+			"maxValue": 65535,
+			"defaultValue": 0,
+			"readOnly": true
+		},
 		{
 			"#": "13",
 			"label": "Off",
@@ -133,6 +199,16 @@
 			"minValue": 0,
 			"maxValue": 1,
 			"defaultValue": 0
+		},
+		{
+			"#": "15",
+			"$if": "firmwareVersion >= 3.0",
+			"label": "Calibration status",
+			"description": "Aplies to devices with firmware version 3.30 or higher",
+			"valueSize": 4,
+			"minValue": 0,
+			"maxValue": 65535,
+			"defaultValue": 0
 		}
 	]
 }

package/config/devices/0x0097/{imoduledouble_1.4.json → imoduledouble.json}

@@ -10,7 +10,7 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "1.4",
+		"min": "0.0",
 		"max": "255.255"
 	}
 }

package/config/devices/0x0099/{gwpn1_3.0.json → gwpn1.json}

@@ -11,7 +11,7 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "3.0",
+		"min": "0.0",
 		"max": "255.255"
 	},
 	"associations": {
@@ -39,8 +39,8 @@
 			"#": "0",
 			"label": "Min. variation of load current",
 			"description": "Minimum variation in load current before a message is sent.",
-			"unit": "%",
 			"valueSize": 1,
+			"unit": "%",
 			"minValue": 0,
 			"maxValue": 100,
 			"defaultValue": 0

package/config/devices/0x0109/{azl7434_5.1-5.1.json → azl7434.json}

@@ -11,8 +11,8 @@
 		}
 	],
 	"firmwareVersion": {
-		"min": "5.1",
-		"max": "5.1"
+		"min": "0.0",
+		"max": "255.255"
 	},
 	"metadata": {
 		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZL 7434-5 to your controller. To get in the “inclusion” mode, the distance between module and controller is suggested to be in one meter. Press 3 times program switch within 2 seconds or turn on the wall switch 3 times within 2 seconds (or press toggle switch 3 times) to be included",

package/config/devices/0x0109/zm1602.json

@@ -2,16 +2,97 @@
 	"manufacturer": "Vision Security",
 	"manufacturerId": "0x0109",
 	"label": "ZM1602",
-	"description": "Wireless Siren & Strobe Alarm, Backup battery type",
+	"description": "AC/DC Siren",
 	"devices": [
+		{
+			"productType": "0x2005",
+			"productId": "0x0503"
+		},
 		{
 			"productType": "0x2009",
 			"productId": "0x0901",
 			"zwaveAllianceId": [609, 610]
+		},
+		{
+			"productType": "0x2009",
+			"productId": "0x0907",
+			"zwaveAllianceId": 1276
+		},
+		{
+			"productType": "0x2009",
+			"productId": "0x0903"
+		},
+		{
+			"productType": "0x2009",
+			"productId": "0x0908",
+			"zwaveAllianceId": 2901
 		}
 	],
 	"firmwareVersion": {
 		"min": "0.0",
 		"max": "255.255"
+	},
+	"paramInformation": [
+		{
+			"#": "0",
+			"label": "Siren Strobe Mode",
+			"description": "Defines the reaction of the siren",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 255,
+			"defaultValue": 0,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "Strobe and Siren",
+					"value": 0
+				},
+				{
+					"label": "Siren",
+					"value": 1
+				},
+				{
+					"label": "Strobe",
+					"value": 2
+				}
+			]
+		},
+		{
+			"#": "1",
+			"$if": "firmwareVersion >= 15.0",
+			"label": "Alarm auto stop",
+			"description": "Defines the auto time out of the alarm indication",
+			"valueSize": 1,
+			"minValue": 0,
+			"maxValue": 255,
+			"defaultValue": 0,
+			"unsigned": true,
+			"allowManualEntry": false,
+			"options": [
+				{
+					"label": "30 seconds",
+					"value": 0
+				},
+				{
+					"label": "60 seconds",
+					"value": 1
+				},
+				{
+					"label": "120 seconds",
+					"value": 2
+				},
+				{
+					"label": "Continuous",
+					"value": 3
+				}
+			]
+		}
+	],
+	"metadata": {
+		"inclusion": "Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZM 1602 to your controller. To get in the “inclusion” mode, the distance between siren and controller is suggested to be in one meter. Open the bracket and press the program switch of ZM 1602 for 1 second at least & release to be included. After setting, the LED Setting Lighting should go off",
+		"exclusion": "Set up the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZM 1602 from your controller. Press the Tamper Switch of ZM 1602 for 1 second at least & release to be excluded",
+		"reset": "This device can’t be reset manually. It is reset to factory defaults when it is excluded. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
+		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1276/ZM%201602-5%20Siren_R3_20170301.pdf"
 	}
 }

package/config/devices/0x0109/{zp3102_0.0-7.99.json → zp3102.json}

@@ -26,12 +26,13 @@
 		},
 		{
 			"productType": "0x2002",
-			"productId": "0x0205"
+			"productId": "0x0205",
+			"zwaveAllianceId": [1070, 1702]
 		}
 	],
 	"firmwareVersion": {
 		"min": "0.0",
-		"max": "7.99"
+		"max": "255.255"
 	},
 	"associations": {
 		"1": {
@@ -43,7 +44,7 @@
 	"paramInformation": [
 		{
 			"#": "1",
-			"label": "On time in minutes",
+			"label": "On Time",
 			"description": "Delay before sending OFF",
 			"valueSize": 1,
 			"unit": "minutes",

package/config/devices/0x0109/zp3111-5.json

@@ -46,7 +46,7 @@
 			"#": "3",
 			"label": "Humidity",
 			"description": "Configure Relative Humidity",
-			"unit": "percent",
+			"unit": "%",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 50,
@@ -55,7 +55,7 @@
 		{
 			"#": "4",
 			"label": "Light Sensor",
-			"unit": "percent",
+			"unit": "%",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 50,
@@ -65,11 +65,11 @@
 			"#": "5",
 			"label": "Trigger Interval",
 			"description": "Set the trigger interval for motion sensor re-activation.",
-			"unit": "seconds",
+			"unit": "minutes",
 			"valueSize": 1,
 			"minValue": 1,
 			"maxValue": 255,
-			"defaultValue": 180,
+			"defaultValue": 3,
 			"unsigned": true
 		},
 		{