@zwave-js/config 10.0.0-beta.1 → 10.0.0-beta.3

package/config/devices/0x0001/zrp200.json

@@ -2,7 +2,7 @@
 	"manufacturer": "HomePro",
 	"manufacturerId": "0x0001",
 	"label": "ZRP200",
-	"description": "Applicance Module",
+	"description": "Appliance Module",
 	"devices": [
 		{
 			"productType": "0x7fff",

package/config/devices/0x0039/th6320zw.json

@@ -182,5 +182,10 @@
 			"#": "42",
 			"$import": "templates/honeywell_template.json#temperature_offset"
 		}
-	]
+	],
+	"compat": {
+		// The device responds in a weird way to these requests which causes S2 collisions
+		"skipConfigurationNameQuery": true,
+		"skipConfigurationInfoQuery": true
+	}
 }

package/config/devices/0x004f/fxs-m08.json

@@ -60,7 +60,7 @@
 		{
 			"#": "5",
 			"label": "External Switch Type",
-			"description": "1. one push button：  when the configuration setting is one push button, only s1 input will be valid. the control moving commands can be accepted in this switch type while the shutter is moving. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 just like the operation of include button. when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving s1 is short pressed again, the shutter will stop moving. a third short pressing of s1 will move the shutter down toward bottom(0x00). while in this moving s1 is short pressed again, the shutter will stop moving. and so on… inverting direction and stopping.   2. two push button： (the default setting is two push button (2))  if this setting is configured as two push button, s1 and s2 input will be valid, but will not accept pressing s1and s2 at the same time. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 or s2 just like the operation of include button.  when s1 is pressed and hold more than 1.5 seconds, the shutter will move up toward top(0x63), and the shutter will stop moving when s1 is released. when s2 is pressed and hold more than 1.5 seconds, the shutter will move down toward bottom(0x00), and the shutter will stop moving when s2 is released.   when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving short pressed s1 again, the shutter just keep moving up toward top(0x63). the easy way to stop this moving is short pressing s2. when s2 is short pressed, the shutter will move down toward botton(0x00). while in this moving short pressed s2 again, the shutter just keep moving down toward botton(0x00). the easy way to stop this moving is short pressing s1.    when in two push button switch type, s1 or s2 are pressed and not released, and fxs-m08 receive any control moving command from Z-Wave rf (ex. basic_set、binary_switch_set、multilevel_switch_set、multilevel_switch_start_level_change or multilevel_switch_stop_level_change or scene_activation_set), fxs-m08 won’t do any change in position but report alarm to group1 (alarm_type=1, alarm_level =0xff), this indicate that the s1 or s2 not been release.  att. : for avoid misunderstanding that rf command dose not work, it is recommended to check the status of s1 and s2",
+			"description": "1. one push button：  when the configuration setting is one push button, only s1 input will be valid. the control moving commands can be accepted in this switch type while the shutter is moving. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 just like the operation of include button. when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving s1 is short pressed again, the shutter will stop moving. a third short pressing of s1 will move the shutter down toward bottom(0x00). while in this moving s1 is short pressed again, the shutter will stop moving. and so on… inverting direction and stopping.   2. two push button： (the default setting is two push button (2))  if this setting is configured as two push button, s1 and s2 input will be valid, but will not accept pressing s1and s2 at the same time. in this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing s1 or s2 just like the operation of include button.  when s1 is pressed and hold more than 1.5 seconds, the shutter will move up toward top(0x63), and the shutter will stop moving when s1 is released. when s2 is pressed and hold more than 1.5 seconds, the shutter will move down toward bottom(0x00), and the shutter will stop moving when s2 is released.   when s1 is short pressed, the shutter will move up toward top(0x63). while in this moving short pressed s1 again, the shutter just keep moving up toward top(0x63). the easy way to stop this moving is short pressing s2. when s2 is short pressed, the shutter will move down toward button(0x00). while in this moving short pressed s2 again, the shutter just keep moving down toward button(0x00). the easy way to stop this moving is short pressing s1.    when in two push button switch type, s1 or s2 are pressed and not released, and fxs-m08 receive any control moving command from Z-Wave rf (ex. basic_set、binary_switch_set、multilevel_switch_set、multilevel_switch_start_level_change or multilevel_switch_stop_level_change or scene_activation_set), fxs-m08 won’t do any change in position but report alarm to group1 (alarm_type=1, alarm_level =0xff), this indicate that the s1 or s2 not been release.  att. : for avoid misunderstanding that rf command dose not work, it is recommended to check the status of s1 and s2",
 			"valueSize": 1,
 			"unit": "seconds",
 			"defaultValue": 2,

package/config/devices/0x0059/max10y-376.json

@@ -25,7 +25,7 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "Diable fail safe timer",
+					"label": "Disable fail safe timer",
 					"value": 0
 				},
 				{

package/config/devices/0x0059/sir-321.json

@@ -44,7 +44,7 @@
 		{
 			"#": "2",
 			"label": "Temperature Scale",
-			"description": "Set the Temperatur scale to Celsius",
+			"description": "Set the Temperature scale to Celsius",
 			"valueSize": 2,
 			"unit": "°C",
 			"minValue": 0,

package/config/devices/0x0060/ad146.json

@@ -53,7 +53,7 @@
 		{
 			"#": "4",
 			"label": "Switching type",
-			"description": "Edge or toogle switch mode.",
+			"description": "Edge or toggle switch mode.",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"unsigned": true,
@@ -64,7 +64,7 @@
 					"value": 0
 				},
 				{
-					"label": "Toogle Mode",
+					"label": "Toggle Mode",
 					"value": 1
 				}
 			]

package/config/devices/0x0060/an179.json

@@ -74,7 +74,7 @@
 		{
 			"#": "4",
 			"label": "Switching type",
-			"description": "Edge or toogle switch mode.",
+			"description": "Edge or toggle switch mode.",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"unsigned": true,
@@ -85,7 +85,7 @@
 					"value": 0
 				},
 				{
-					"label": "Toogle Mode",
+					"label": "Toggle Mode",
 					"value": 1
 				}
 			]

package/config/devices/0x0063/53831_zw5314.json

@@ -40,7 +40,7 @@
 		"treatBasicSetAsEvent": true
 	},
 	"metadata": {
-		"inclusion": "1. Follow the instructions for your Z-Wave certified hub to add a device tothe Z-Wave network.\n2. Once the hub is ready to add your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends add notification (NIF).\n4. The LED will keep lighting up for one minute if inclusion is successful.\n5. Following the instructions for your Z-Wave certified hub, assign actions for each button press. An action can be many combinations of scenes, groups or events, and is greatly dependent on the hub capabilities.",
+		"inclusion": "1. Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.\n2. Once the hub is ready to add your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends add notification (NIF).\n4. The LED will keep lighting up for one minute if inclusion is successful.\n5. Following the instructions for your Z-Wave certified hub, assign actions for each button press. An action can be many combinations of scenes, groups or events, and is greatly dependent on the hub capabilities.",
 		"exclusion": "1. Follow the instructions for your Z-Wave certified hub to remove a device from the Z-Wave network.\n2. Once the hub is ready to remove your device, press and hold either button for three seconds.\n3. The LED will flash two times when the remote sends remove notification (NIF)",
 		"reset": "1. Press and release button 1 10 times quickly. All button presses must be within six seconds.\n2. The LED will flash five times when completed successfully.",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3959/53831-QSG-v1%20(3).pdf"

package/config/devices/0x0068/78008.json

@@ -87,7 +87,7 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "Alwas wake up",
+					"label": "Always wake up",
 					"value": 0
 				},
 				{

package/config/devices/0x0085/arz_z-wave.json

@@ -47,7 +47,7 @@
 	],
 	"metadata": {
 		"inclusion": "Autoinclusion - This feature allow you to add hard to reach devices to Z-Wave network. 3-times ON and OFF the power roller shutter (OFF-ON-OFF-ON-OFF-ON) causes the introduction of roller shutter to Autoinclusion mode. Please note that the procedure has been started the time between on and off can not exceed 20s. Autoinclusion mode is activated for a maximum of 10 minutes. During this time, we can add an awning to any Z-Wave controller running in the Include procedure.\n\nInclude - This function allow you to add roller shutter to the network Z-Wave. Follow the procedur adding device to the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second",
-		"exclusion": "Exclude - This function allow you to remove roller shutter from the network Z-Wave. Follow the procedur removing device from the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second. Function removes information only about newtork Z-Wave",
+		"exclusion": "Exclude - This function allow you to remove roller shutter from the network Z-Wave. Follow the procedur removing device from the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second. Function removes information only about network Z-Wave",
 		"reset": "Device Reset Locally – This function allows you to reset the Z-Wave network without the use of Z-Wave controller. Press 5 times the programming button P fast, the roller shutter was removed from the Z-Wave network, restore the default parameters, name and locations. \nPlease use this procedure only when the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2571/170307%20ARZ%20Z-WAVE%20User%20Manual.pdf"
 	}

package/config/devices/0x0086/zv9001t4-dim.json

@@ -37,7 +37,7 @@
 		},
 		{
 			"#": "4",
-			"label": "Scene Command Targer",
+			"label": "Scene Command Target",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,
@@ -47,7 +47,7 @@
 					"value": 0
 				},
 				{
-					"label": "Assocciation Group",
+					"label": "Association Group",
 					"value": 1
 				}
 			]

package/config/devices/0x008a/alarm_sound.json

@@ -49,8 +49,8 @@
 		},
 		{
 			"#": "3",
-			"label": "Desitnation routine succes time",
-			"description": "Time it takes to send a new frame after the last frame has succesfully send",
+			"label": "Desitnation routine success time",
+			"description": "Time it takes to send a new frame after the last frame has successfully send",
 			"valueSize": 1,
 			"minValue": 0,
 			"maxValue": 60,

package/config/devices/0x008b/zw111.json

@@ -109,7 +109,7 @@
 		},
 		{
 			"#": "81",
-			"label": "Group 3 notificaiton",
+			"label": "Group 3 notification",
 			"description": "Set notification sent to associated nodes (group 3)",
 			"valueSize": 1,
 			"defaultValue": 0,
@@ -127,7 +127,7 @@
 		},
 		{
 			"#": "82",
-			"label": "Group 4 notificaiton",
+			"label": "Group 4 notification",
 			"description": "Set notification sent to associated nodes (group 4)",
 			"valueSize": 1,
 			"defaultValue": 1,

package/config/devices/0x0109/zf5201eu-5.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZF5201 to the controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
 		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
-		"reset": "Triger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1718/ZF%205201-5_20141118.pdf"
 	}
 }

package/config/devices/0x0109/zp3111-5.json

@@ -133,7 +133,7 @@
 	"metadata": {
 		"inclusion": "To add the ZP3111 to the Z-Wave network (inclusion), place the Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds.",
 		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
-		"reset": "Remove cover to trigged tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
+		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2479/ZP3111-5_R2_20170316.pdf"
 	}
 }

package/config/devices/0x010b/dn3g6ja069.json

@@ -61,7 +61,7 @@
 		{
 			"#": "2",
 			"label": "Enable Switch of Alarm Notification Report",
-			"description": "Configure to send which the sensor values arbitralily. the sensor values can be selected from human detect and open/close",
+			"description": "Configure to send which the sensor values arbitrarily. the sensor values can be selected from human detect and open/close",
 			"valueSize": 1,
 			"defaultValue": 3,
 			"unsigned": true,

package/config/devices/0x010f/fgk101.json

@@ -545,7 +545,7 @@
 			"$if": "firmwareVersion >= 3.2",
 			"$import": "~/templates/master_template.json#base_enable_disable",
 			"label": "Scene: Holding",
-			"description": "Only available if Operations Mode (paramater 1) is set to external button",
+			"description": "Only available if Operations Mode (parameter 1) is set to external button",
 			"valueSize": 2
 		},
 		{
@@ -553,7 +553,7 @@
 			"$if": "firmwareVersion >= 3.2",
 			"$import": "~/templates/master_template.json#base_enable_disable",
 			"label": "Scene: Releasing",
-			"description": "Only available if Operations Mode (paramater 1) is set to external button",
+			"description": "Only available if Operations Mode (parameter 1) is set to external button",
 			"valueSize": 2
 		},
 		{
@@ -561,7 +561,7 @@
 			"$if": "firmwareVersion >= 3.2",
 			"$import": "~/templates/master_template.json#base_enable_disable",
 			"label": "Scene: Double Click",
-			"description": "Only available if Operations Mode (paramater 1) is set to external button",
+			"description": "Only available if Operations Mode (parameter 1) is set to external button",
 			"valueSize": 2
 		},
 		{
@@ -569,7 +569,7 @@
 			"$if": "firmwareVersion >= 3.2",
 			"$import": "~/templates/master_template.json#base_enable_disable",
 			"label": "Scene: Triple Click",
-			"description": "Only available if Operations Mode (paramater 1) is set to external button",
+			"description": "Only available if Operations Mode (parameter 1) is set to external button",
 			"valueSize": 2
 		},
 		{

package/config/devices/0x010f/fgms001.json

@@ -145,7 +145,7 @@
 			"#": "6",
 			"$if": "firmwareVersion <= 3.1",
 			"label": "Motion Alarm Cancellation Delay",
-			"description": "Period of time after wich Motion alarm will be cancelled.",
+			"description": "Period of time after which Motion alarm will be cancelled.",
 			"valueSize": 2,
 			"minValue": 1,
 			"maxValue": 65535,
@@ -156,7 +156,7 @@
 			"#": "6",
 			"$if": "firmwareVersion >= 3.2",
 			"label": "Motion detection - alarm cancellation delay",
-			"description": "Period of time after wich Motion alarm will be cancelled.",
+			"description": "Period of time after which Motion alarm will be cancelled.",
 			"valueSize": 2,
 			"minValue": 1,
 			"maxValue": 32767,

package/config/devices/0x010f/fgwceu-201.json

@@ -143,7 +143,7 @@
 		{
 			"#": "153",
 			"$import": "#paramInformation/152",
-			"label": "Second Chanel: Double Click Value"
+			"label": "Second Channel: Double Click Value"
 		}
 	]
 }

package/config/devices/0x0115/kfob.json

@@ -245,7 +245,7 @@
 		{
 			"#": "20",
 			"label": "Typical click timeout",
-			"description": "Typical time used to differenciate click, hold and double clicks in 10ms units",
+			"description": "Typical time used to differentiate click, hold and double clicks in 10ms units",
 			"valueSize": 1,
 			"minValue": 0,
 			"maxValue": 255,

package/config/devices/0x0115/v3.json

@@ -186,7 +186,7 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "Comfirm OTA",
+					"label": "Confirm OTA",
 					"value": 1
 				}
 			]

package/config/devices/0x0115/zme_ft.json

@@ -110,7 +110,7 @@
 		{
 			"#": "10",
 			"label": "Typical click timeout",
-			"description": "Typical time used to differenciate click from hold",
+			"description": "Typical time used to differentiate click from hold",
 			"unit": "in 10ms",
 			"valueSize": 1,
 			"minValue": 1,

package/config/devices/0x0116/hac01.json

@@ -2,7 +2,7 @@
 	"manufacturer": "Chromagic Technologies Corporation",
 	"manufacturerId": "0x0116",
 	"label": "HAC01",
-	"description": "Chromagic Z-Wave Remote Botton (EU)",
+	"description": "Chromagic Z-Wave Remote Button (EU)",
 	"devices": [
 		{
 			"productType": "0x0010",

package/config/devices/0x0116/itemp.json

@@ -50,7 +50,7 @@
 		{
 			"#": "2",
 			"label": "Command sent on external dry contact",
-			"description": "Configure what te external contact sends when trigger",
+			"description": "Configure what the external contact sends when triggered",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"unsigned": true,

package/config/devices/0x0118/tz06.json

@@ -118,7 +118,7 @@
 					"value": 0
 				},
 				{
-					"label": "Switch Ingore",
+					"label": "Switch Ignore",
 					"value": 1
 				},
 				{

package/config/devices/0x0118/tz36d.json

@@ -67,7 +67,7 @@
 					"value": 0
 				},
 				{
-					"label": "Switch top and buttom button.",
+					"label": "Switch top and bottom button.",
 					"value": 1
 				}
 			]

package/config/devices/0x0118/tz65d.json

@@ -89,7 +89,7 @@
 		{
 			"#": "4",
 			"label": "Invert Switch",
-			"description": "To change the top of the switch to off and the botton to on",
+			"description": "To change the top of the switch to off and the button to on",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,

package/config/devices/0x0118/tz66d.json

@@ -91,7 +91,7 @@
 		{
 			"#": "4",
 			"label": "Invert Switch",
-			"description": "To change the top of the switch to off and the botton to on",
+			"description": "To change the top of the switch to off and the button to on",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,

package/config/devices/0x0118/tz74.json

@@ -35,7 +35,7 @@
 		{
 			"#": "2",
 			"label": "Memory Function",
-			"description": "Default with memory: the socket staus is same as before when power is on",
+			"description": "Default with memory: the socket status is same as before when power is on",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,

package/config/devices/0x0118/tz75.json

@@ -34,7 +34,7 @@
 		},
 		{
 			"#": "3",
-			"label": "Treshold of watt for load caution",
+			"label": "Threshold of watt for load caution",
 			"unit": "W",
 			"valueSize": 2,
 			"minValue": 10,
@@ -43,7 +43,7 @@
 		},
 		{
 			"#": "4",
-			"label": "Treshold of KWH for load caution",
+			"label": "Threshold of KWH for load caution",
 			"unit": "KWH",
 			"valueSize": 2,
 			"minValue": 0,

package/config/devices/0x011b/eedomus.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "You can proceed to a Z-Wave chip factory reset in order to do a fresh installation of your network.\n\nWhen doing that the Home ID of your network will change and your devices need to be excluded (In order to be reseted) and included again.\n\nTo perform a factory reset, click on :\nConfiguration / Add or remove a device / Advanced Z-Wave functions / Reset Z-Wave controller\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. \nIf this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "You can proceed to a Z-Wave chip factory reset in order to do a fresh installation of your network.\n\nWhen doing that the Home ID of your network will change and your devices need to be excluded (in order to be reset) and included again.\n\nTo perform a factory reset, click on :\nConfiguration / Add or remove a device / Advanced Z-Wave functions / Reset Z-Wave controller\n\nIf this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. \nIf this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3582/eedomus_guide_en.pdf"
 	}
 }

package/config/devices/0x0131/ne-nas-pd01z.json

@@ -17,7 +17,7 @@
 		{
 			"#": "1",
 			"label": "Sensitivity level",
-			"description": "8 = Highest sensitivity, 255 = lowest sesitivity",
+			"description": "8 = Highest sensitivity, 255 = lowest sensitivity",
 			"valueSize": 1,
 			"minValue": 8,
 			"maxValue": 255,

package/config/devices/0x013c/psp05.json

@@ -62,7 +62,7 @@
 		},
 		{
 			"#": "10",
-			"label": "Batery level reporting interval",
+			"label": "Battery level reporting interval",
 			"description": "How frequently battery status should be reported",
 			"valueSize": 1,
 			"minValue": 0,

package/config/devices/0x013c/pst02-a-br.json

@@ -250,7 +250,7 @@
 		},
 		{
 			"#": "11",
-			"label": "Auto Report Door/Windo W State",
+			"label": "Auto Report Door/Window State",
 			"description": "The default value is 12. the tick time can setting by the configuration no.20",
 			"valueSize": 1,
 			"minValue": 0,

package/config/devices/0x0149/wps104.json

@@ -85,7 +85,7 @@
 		{
 			"#": "32",
 			"label": "Next State",
-			"description": "Defines the next state if an overcurrent event occurr",
+			"description": "Defines the next state if an overcurrent event occur",
 			"valueSize": 1,
 			"defaultValue": 0,
 			"allowManualEntry": false,

package/config/devices/0x014d/ibdk-01.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Please excute this reset procedure only when the primary controller is missing or inoperable.\n1. Open battery cover.\n2. Press and hold the button there\n3. LED is turned on after 5 seconds. Keep holding.\n4. LET starts blinking after 10 seconds.\n5. Release the button when the LED blinks",
+		"reset": "Please execute this reset procedure only when the primary controller is missing or inoperable.\n1. Open battery cover.\n2. Press and hold the button there\n3. LED is turned on after 5 seconds. Keep holding.\n4. LET starts blinking after 10 seconds.\n5. Release the button when the LED blinks",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3209/UVA01A_Manual_20190111.pdf"
 	}
 }

package/config/devices/0x014f/wf00z.json

@@ -17,7 +17,7 @@
 	"metadata": {
 		"inclusion": "For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZF5201 to the controller. To get in the “inclusion” mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZF5201 for 1 second at least. The LED on the ZF5201 should go solid, if not, please try again",
 		"exclusion": "For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZF5201 from your controller. Press the program switch of ZF5201 for 1 second at least to be excluded",
-		"reset": "Triger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
+		"reset": "Trigger the Water Sensor 10 times within 10 sec. The device will send command class of device reset to controller and back to the factory default state. Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1590/10008416X4%20WF00Z-1%20Instructions.pdf"
 	}
 }

package/config/devices/0x0154/123665.json

@@ -84,7 +84,7 @@
 		},
 		{
 			"#": "11",
-			"label": "Disable Switching Funktion",
+			"label": "Disable Switching Function",
 			"valueSize": 1,
 			"defaultValue": 1,
 			"allowManualEntry": false,

package/config/devices/0x0159/zmnhaa.json

@@ -60,11 +60,11 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "NO (normaly open) input type",
+					"label": "NO (normally open) input type",
 					"value": 0
 				},
 				{
-					"label": "NC (normaly close) input type",
+					"label": "NC (normally close) input type",
 					"value": 1
 				}
 			]
@@ -78,11 +78,11 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "NO (normaly open) input type",
+					"label": "NO (normally open) input type",
 					"value": 0
 				},
 				{
-					"label": "NC (normaly close) input type",
+					"label": "NC (normally close) input type",
 					"value": 1
 				}
 			]

package/config/devices/0x0159/zmnhad.json

@@ -41,11 +41,11 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "NO (normaly open) input type",
+					"label": "NO (normally open) input type",
 					"value": 0
 				},
 				{
-					"label": "NC (normaly close) input type",
+					"label": "NC (normally close) input type",
 					"value": 1
 				}
 			]
@@ -59,11 +59,11 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "NO (normaly open) input type",
+					"label": "NO (normally open) input type",
 					"value": 0
 				},
 				{
-					"label": "NC (normaly close) input type",
+					"label": "NC (normally close) input type",
 					"value": 1
 				}
 			]

package/config/devices/0x0159/zmnhkd.json

@@ -140,7 +140,7 @@
 					"value": 2000
 				},
 				{
-					"label": "Input I2 doesnt influence on the Heat/Cool process",
+					"label": "Input I2 doesn't influence on the Heat/Cool process",
 					"value": 32767
 				}
 			]

package/config/devices/0x0159/zmnhld.json

@@ -174,7 +174,7 @@
 					"value": 2000
 				},
 				{
-					"label": "Input I2 doesnt influence on the Heat/Cool process",
+					"label": "Input I2 doesn't influence on the Heat/Cool process",
 					"value": 32767
 				}
 			]

package/config/devices/0x0159/zmnhnd.json

@@ -41,11 +41,11 @@
 			"allowManualEntry": false,
 			"options": [
 				{
-					"label": "NO (normaly open) input type",
+					"label": "NO (normally open) input type",
 					"value": 0
 				},
 				{
-					"label": "NC (normaly close) input type",
+					"label": "NC (normally close) input type",
 					"value": 1
 				}
 			]

package/config/devices/0x0159/zmnhtd.json

@@ -121,7 +121,7 @@
 		},
 		{
 			"#": "42",
-			"label": "Power (W) Reporting Interal",
+			"label": "Power (W) Reporting Internal",
 			"description": "Allowable range: 60-32535",
 			"unit": "seconds",
 			"valueSize": 2,

package/config/devices/0x015b/lap255u.json

@@ -15,7 +15,7 @@
 		"max": "255.255"
 	},
 	"metadata": {
-		"reset": "Run Z-Wave Certification Application in Setting, Select \"Things\" on the left menu, select \"bridge\" on the right list, andd Select factoryReset on the right list, push Send button on the Pop up",
+		"reset": "Run Z-Wave Certification Application in Setting, Select \"Things\" on the left menu, select \"bridge\" on the right list, and Select factoryReset on the right list, push Send button on the Pop up",
 		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1453/ZwaveCertiApp_Guide_0902_new.pdf"
 	}
 }

package/config/devices/0x015f/mh-c421.json

@@ -147,7 +147,7 @@
 					"value": 0
 				},
 				{
-					"label": "Toogle (2-state switches)",
+					"label": "Toggle (2-state switches)",
 					"value": 1
 				}
 			]

package/config/devices/0x0165/msp-3-1-x1.json

@@ -256,7 +256,7 @@
 		{
 			"#": "24",
 			"label": "Metering Heartbeat",
-			"description": "Reporting intervall for power and energy to lifeline.",
+			"description": "Reporting interval for power and energy to lifeline.",
 			"unit": "s",
 			"valueSize": 2,
 			"minValue": 0,