rsmp_schema 0.4.4 → 0.4.5

data/schemas/tlc/1.1/commands/M0013.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Activate a series of inputs\n\nSet given inputs (1-255) of the controllers general purpose I/O to either true or false. This command was introduced due to coordination requirements needing to set many inputs to true/false at the same time and M0006 being to slow to send a message for each input individually. With this command many inputs can be set to true/false at the same time using a single command message. It can be used for all types of input where the traffic light controller must react to external control. Typical usages are bus priority, coordination between traffic controllers, external control systems, and much more.\n\nRequires security code 2.\n\nThe parameter ‘status’ sets/unsets a block of 16 inputs at a time. It can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon. Format: [Offset];[Bits to set];[Bits to unset];…\n\n- ‘Offset’ defines where the 16 inputs starts from\n- ‘Bits to set’ defines which bit(s) to set. ‘0’ if unused\n- ‘Bits to unset’ defines which bit(s) to unset. ‘0’ if unused\n\nExample 1:\n“3,4134,65” sets input 4,5,8,15 and unsets 3,9\n- Input starts from no. 5\n- “4134” is 1 0000 0010 0110 in binary, but since input starts from 3, it is shifted 3 bits, e.g. 1000 0001 0011 0000 which are bits 4,5,8,15\n- “65” is 100 0001 in binary, but since input starts from 3, it is shifted 3 bits, e.g. 10 0000 1000 which are bits 3,9\n\nExample 2:\n“12,1,4” sets input 12 and unsets 14\n- Input starts from no. 12\n- “1” is 1 in binary, but since input starts at 12 it is shifted 12 bits, e.g. 1 0000 0000 0000, which is bit 12\n- “4” is 100 in binary, but since input starts at 12 it is shifted 12 bits, e.g. 100 0000 0000 0000, which is bit 14\n\nAnd both these examples could be sent in the same message as: “3,4143,65;12,1,4”\n\nSuch a message would set input 4,5,8,12,15 and unset input 3,9,14\n\nExample 3:\n“0,1,2” sets input 0 and unsets 1\n- Input starts from 0\n- “1” is 1 in binary, which is bit 0\n- “2” is 10 in binary, which is bit 1",
   "allOf" : [
     {
-      "description" : "Activate a series of inputs\n\nSet given inputs (1-255) of the controllers general purpose I/O to either true or false. This command was introduced due to coordination requirements needing to set many inputs to true/false at the same time and M0006 being to slow to send a message for each input individually. With this command many inputs can be set to true/false at the same time using a single command message. It can be used for all types of input where the traffic light controller must react to external control. Typical usages are bus priority, coordination between traffic controllers, external control systems, and much more.\n\nRequires security code 2.\n\nThe parameter ‘status’ sets/unsets a block of 16 inputs at a time. It can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon. Format: [Offset];[Bits to set];[Bits to unset];…\n\n- ‘Offset’ defines where the 16 inputs starts from\n- ‘Bits to set’ defines which bit(s) to set. ‘0’ if unused\n- ‘Bits to unset’ defines which bit(s) to unset. ‘0’ if unused\n\nExample 1:\n“3,4134,65” sets input 4,5,8,15 and unsets 3,9\n- Input starts from no. 5\n- “4134” is 1 0000 0010 0110 in binary, but since input starts from 3, it is shifted 3 bits, e.g. 1000 0001 0011 0000 which are bits 4,5,8,15\n- “65” is 100 0001 in binary, but since input starts from 3, it is shifted 3 bits, e.g. 10 0000 1000 which are bits 3,9\n\nExample 2:\n“12,1,4” sets input 12 and unsets 14\n- Input starts from no. 12\n- “1” is 1 in binary, but since input starts at 12 it is shifted 12 bits, e.g. 1 0000 0000 0000, which is bit 12\n- “4” is 100 in binary, but since input starts at 12 it is shifted 12 bits, e.g. 100 0000 0000 0000, which is bit 14\n\nAnd both these examples could be sent in the same message as: “3,4143,65;12,1,4”\n\nSuch a message would set input 4,5,8,12,15 and unset input 3,9,14\n\nExample 3:\n“0,1,2” sets input 0 and unsets 1\n- Input starts from 0\n- “1” is 1 in binary, which is bit 0\n- “2” is 10 in binary, which is bit 1",
       "properties" : {
         "n" : {
           "enum" : [
@@ -26,47 +26,53 @@
         }
       },
       "then" : {
-        "s" : null
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Sets/Unsets a block of 16 inputs at a time. Can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon.\nFormat: [Offset];[Bits to set];[Bits to unset];…",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Sets/Unsets a block of 16 inputs at a time. Can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon.\nFormat: [Offset];[Bits to set];[Bits to unset];…",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
-          }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.1/commands/M0014.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set dynamic bands.\nCan be used to change between predefined signal timings. Moves the start of signal groups in the cycle.\nThis command can be used to change the split of green time during the cycle. A typical usage is scenario based control where changing of signal timings is used for optimal traffic flow.\nRequires security code 2",
   "allOf" : [
     {
-      "description" : "Set dynamic bands.\nCan be used to change between predefined signal timings. Moves the start of signal groups in the cycle.\nThis command can be used to change the split of green time during the cycle. A typical usage is scenario based control where changing of signal timings is used for optimal traffic flow.\nRequires security code 2",
       "properties" : {
         "n" : {
           "enum" : [
@@ -27,73 +27,79 @@
         }
       },
       "then" : {
-        "s" : null
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "plan"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Plan to be changed"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "plan"
+                }
               }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Dynamic bands.\nEach dynamic band are written as dd-ee where:\ndd=Dynamic band number (from 1-10)\nee=Extension in seconds in this band\n\nEach dynamic band is separated with a comma.\n\nE.g.\ndd-ee,dd-ee",
-            "type" : "string"
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Plan to be changed"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Dynamic bands.\nEach dynamic band are written as dd-ee where:\ndd=Dynamic band number (from 1-10)\nee=Extension in seconds in this band\n\nEach dynamic band is separated with a comma.\n\nE.g.\ndd-ee,dd-ee",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.1/commands/M0015.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set Offset time.\nOffset time is used to define an offset between intersections in coordinated control. It is based on the expected travel time between intersections.\nThis command can be used to fine tune the coordination for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set Offset time.\nOffset time is used to define an offset between intersections in coordinated control. It is based on the expected travel time between intersections.\nThis command can be used to fine tune the coordination for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -27,79 +27,85 @@
         }
       },
       "then" : {
-        "s" : null
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Set offset time in seconds"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
               }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "plan"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Time plan nr"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Set offset time in seconds"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
               }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "plan"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Time plan nr"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.1/commands/M0016.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set week time table.\nSet which time table for signal programs to use for each day during a week.\nThis command changes the signal timings during the week for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set week time table.\nSet which time table for signal programs to use for each day during a week.\nThis command changes the signal timings during the week for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -26,47 +26,53 @@
         }
       },
       "then" : {
-        "s" : null
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Week time table. Defines time table to use for each week day\nEach segment is written as d-t where:\nd=day of week\nt=time table nr\n\nDay of week legend:\n0=Monday\n1=Tuesday\n2=Wednesday\n3=Thursday\n4=Friday\n5=Saturday\n6=Sunday\n\nEach segment is separated with a comma\n\nE.g.\nd-t,d-t",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Week time table. Defines time table to use for each week day\nEach segment is written as d-t where:\nd=day of week\nt=time table nr\n\nDay of week legend:\n0=Monday\n1=Tuesday\n2=Wednesday\n3=Thursday\n4=Friday\n5=Saturday\n6=Sunday\n\nEach segment is separated with a comma\n\nE.g.\nd-t,d-t",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
-          }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.1/commands/M0017.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set time tables.\nSet time of day for when to automatically switch signal program (time plan).\nThis command changes the signal timings according to time of day for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set time tables.\nSet time of day for when to automatically switch signal program (time plan).\nThis command changes the signal timings according to time of day for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -26,47 +26,53 @@
         }
       },
       "then" : {
-        "s" : null
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Time Table. Defines time tables.\nEach time definition is written as t-o-h-m where:\nt=time table nr (1-12)\no=function\nh=hour - switching time\nm=minute - switching minute\n\nFunction legend:\n0=no plan is selected by time table\n1=set plan 1\n…\n16= set plan 16\n\nhour and minute is using local time (not UTC)\n\nEach time definition is separated with a comma.\n\nE.g.\nt-o-h-m,t-o-h-m",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Time Table. Defines time tables.\nEach time definition is written as t-o-h-m where:\nt=time table nr (1-12)\no=function\nh=hour - switching time\nm=minute - switching minute\n\nFunction legend:\n0=no plan is selected by time table\n1=set plan 1\n…\n16= set plan 16\n\nhour and minute is using local time (not UTC)\n\nEach time definition is separated with a comma.\n\nE.g.\nt-o-h-m,t-o-h-m",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
-          }
-        }
+        ]
       }
     }
   ]