rsmp_schema 0.4.3 → 0.4.5

data/schemas/tlc/1.0.15/commands/M0013.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Activate a series of inputs.\nSet given inputs (1-255) of the controllers general purpose I/O to either true or false.\nThis command was introduced due to coordination requirements needing to set many inputs to true/false at the same time and M0006 being to slow to send a message for each input individually. With this command many inputs can be set to true/false at the same time using a single RSMP message.\nCan be used for all types of input where the traffic light controller must react to external control. Typical usages are bus priority, coordination between traffic controllers, external control systems, and much more.\nRequires security code 2",
   "allOf" : [
     {
-      "description" : "Activate a series of inputs.\nSet given inputs (1-255) of the controllers general purpose I/O to either true or false.\nThis command was introduced due to coordination requirements needing to set many inputs to true/false at the same time and M0006 being to slow to send a message for each input individually. With this command many inputs can be set to true/false at the same time using a single RSMP message.\nCan be used for all types of input where the traffic light controller must react to external control. Typical usages are bus priority, coordination between traffic controllers, external control systems, and much more.\nRequires security code 2",
       "properties" : {
         "n" : {
           "enum" : [
@@ -17,41 +17,62 @@
     {
       "if" : {
         "required" : [
-          "n"
+          "q"
         ],
         "properties" : {
-          "n" : {
-            "const" : "status"
+          "q" : {
+            "const" : "undefined"
           }
         }
       },
       "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Sets/Unsets a block of 16 inputs at a time. Can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon. Since semicolon breaks the SXL csv-format, colon, \":\" is used in example below.\n\nFormat: [Offset],[Bits to set],[Bits to unset]:…\n\nOffset sets where the 16 inputs starts from followed by two 16 bit values telling which bit to set and unset in binary format, i.e. first bit have value 1 and last bit have value 32768.\n\nExample 1:\n\"5, 4134, 65\" sets input 6,7,10,17 = on and 5,11 = off\n(Input starts from no. 5 and bit 1,2,5,12 = 1 and bit 0,6 = 0)\n\nExample 2:\n\"22, 1, 4\" sets input 22 = on and 24 = off\n(Input starts from no. 22 and bit 0 = 1 and bit 2 = 0)\n\nAnd both thease examples could be sent in the same message as:\n\"5,4143:65:22,1,4\"\n\nSuch a message would activate input 6,7,10,17,22 and deactivate input 5,11,24",
-            "type" : "string"
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Sets/Unsets a block of 16 inputs at a time. Can be repeated to set several blocks of 16 inputs. Values are separated with comma. Blocks are separated with semicolon. Since semicolon breaks the SXL csv-format, colon, \":\" is used in example below.\n\nFormat: [Offset],[Bits to set],[Bits to unset]:…\n\nOffset sets where the 16 inputs starts from followed by two 16 bit values telling which bit to set and unset in binary format, i.e. first bit have value 1 and last bit have value 32768.\n\nExample 1:\n\"5, 4134, 65\" sets input 6,7,10,17 = on and 5,11 = off\n(Input starts from no. 5 and bit 1,2,5,12 = 1 and bit 0,6 = 0)\n\nExample 2:\n\"22, 1, 4\" sets input 22 = on and 24 = off\n(Input starts from no. 22 and bit 0 = 1 and bit 2 = 0)\n\nAnd both thease examples could be sent in the same message as:\n\"5,4143:65:22,1,4\"\n\nSuch a message would activate input 6,7,10,17,22 and deactivate input 5,11,24",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.0.15/commands/M0014.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set dynamic bands.\nCan be used to change between predefined signal timings. Moves the start of signal groups in the cycle.\nThis command can be used to change the split of green time during the cycle. A typical usage is scenario based control where changing of signal timings is used for optimal traffic flow.\nRequires security code 2",
   "allOf" : [
     {
-      "description" : "Set dynamic bands.\nCan be used to change between predefined signal timings. Moves the start of signal groups in the cycle.\nThis command can be used to change the split of green time during the cycle. A typical usage is scenario based control where changing of signal timings is used for optimal traffic flow.\nRequires security code 2",
       "properties" : {
         "n" : {
           "enum" : [
@@ -18,67 +18,88 @@
     {
       "if" : {
         "required" : [
-          "n"
+          "q"
         ],
         "properties" : {
-          "n" : {
-            "const" : "plan"
+          "q" : {
+            "const" : "undefined"
           }
         }
       },
       "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Plan to be changed"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
-              }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "status"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Dynamic bands.\nEach dynamic band are written as dd-ee where:\ndd=Dynamic band number (from 1-10)\nee=Extension in seconds in this band\n\nEach dynamic band is separated with a comma.\n\nE.g.\ndd-ee,dd-ee",
-            "type" : "string"
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "plan"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Plan to be changed"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Dynamic bands.\nEach dynamic band are written as dd-ee where:\ndd=Dynamic band number (from 1-10)\nee=Extension in seconds in this band\n\nEach dynamic band is separated with a comma.\n\nE.g.\ndd-ee,dd-ee",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.0.15/commands/M0015.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set Offset time.\nOffset time is used to define an offset between intersections in coordinated control. It is based on the expected travel time between intersections.\nThis command can be used to fine tune the coordination for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set Offset time.\nOffset time is used to define an offset between intersections in coordinated control. It is based on the expected travel time between intersections.\nThis command can be used to fine tune the coordination for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -18,73 +18,94 @@
     {
       "if" : {
         "required" : [
-          "n"
+          "q"
         ],
         "properties" : {
-          "n" : {
-            "const" : "status"
+          "q" : {
+            "const" : "undefined"
           }
         }
       },
       "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Set offset time in seconds"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
-              }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "plan"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "allOf" : [
-              {
-                "description" : "Time plan nr"
-              },
-              {
-                "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
               }
-            ]
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
-        }
-      },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Set offset time in seconds"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "plan"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "allOf" : [
+                    {
+                      "description" : "Time plan nr"
+                    },
+                    {
+                      "$ref" : "../../../core/3.1.2/definitions.json#/integer"
+                    }
+                  ]
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.0.15/commands/M0016.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set week time table.\nSet which time table for signal programs to use for each day during a week.\nThis command changes the signal timings during the week for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set week time table.\nSet which time table for signal programs to use for each day during a week.\nThis command changes the signal timings during the week for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -17,41 +17,62 @@
     {
       "if" : {
         "required" : [
-          "n"
+          "q"
         ],
         "properties" : {
-          "n" : {
-            "const" : "status"
+          "q" : {
+            "const" : "undefined"
           }
         }
       },
       "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Week time table. Defines time table to use for each week day\nEach segment is written as d-t where:\nd=day of week\nt=time table nr\n\nDay of week legend:\n0=Monday\n1=Tuesday\n2=Wednesday\n3=Thursday\n4=Friday\n5=Saturday\n6=Sunday\n\nEach segment is separated with a comma\n\nE.g.\nd-t,d-t",
-            "type" : "string"
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Week time table. Defines time table to use for each week day\nEach segment is written as d-t where:\nd=day of week\nt=time table nr\n\nDay of week legend:\n0=Monday\n1=Tuesday\n2=Wednesday\n3=Thursday\n4=Friday\n5=Saturday\n6=Sunday\n\nEach segment is separated with a comma\n\nE.g.\nd-t,d-t",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]

data/schemas/tlc/1.0.15/commands/M0017.json

@@ -1,7 +1,7 @@
 {
+  "description" : "Set time tables.\nSet time of day for when to automatically switch signal program (time plan).\nThis command changes the signal timings according to time of day for optimal traffic flow.\nRequires security code 2.",
   "allOf" : [
     {
-      "description" : "Set time tables.\nSet time of day for when to automatically switch signal program (time plan).\nThis command changes the signal timings according to time of day for optimal traffic flow.\nRequires security code 2.",
       "properties" : {
         "n" : {
           "enum" : [
@@ -17,41 +17,62 @@
     {
       "if" : {
         "required" : [
-          "n"
+          "q"
         ],
         "properties" : {
-          "n" : {
-            "const" : "status"
+          "q" : {
+            "const" : "undefined"
           }
         }
       },
       "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Time Table. Defines time tables.\nEach time definition is written as t-o-h-m where:\nt=time table nr (1-12)\no=function\nh=hour - switching time\nm=minute - switching minute\n\nFunction legend:\n0=no plan is selected by time table\n1=set plan 1\n…\n16= set plan 16\n\nhour and minute is using local time (not UTC)\n\nEach time definition is separated with a comma.\n\nE.g.\nt-o-h-m,t-o-h-m",
-            "type" : "string"
-          }
-        }
-      }
-    },
-    {
-      "if" : {
-        "required" : [
-          "n"
-        ],
-        "properties" : {
-          "n" : {
-            "const" : "securityCode"
-          }
+        "s" : {
+          "type" : "null"
         }
       },
-      "then" : {
-        "properties" : {
-          "v" : {
-            "description" : "Security code 2",
-            "type" : "string"
+      "else" : {
+        "allOf" : [
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "status"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Time Table. Defines time tables.\nEach time definition is written as t-o-h-m where:\nt=time table nr (1-12)\no=function\nh=hour - switching time\nm=minute - switching minute\n\nFunction legend:\n0=no plan is selected by time table\n1=set plan 1\n…\n16= set plan 16\n\nhour and minute is using local time (not UTC)\n\nEach time definition is separated with a comma.\n\nE.g.\nt-o-h-m,t-o-h-m",
+                  "type" : "string"
+                }
+              }
+            }
+          },
+          {
+            "if" : {
+              "required" : [
+                "n"
+              ],
+              "properties" : {
+                "n" : {
+                  "const" : "securityCode"
+                }
+              }
+            },
+            "then" : {
+              "properties" : {
+                "v" : {
+                  "description" : "Security code 2",
+                  "type" : "string"
+                }
+              }
+            }
           }
-        }
+        ]
       }
     }
   ]