stc8isp 0.3.0__py3-none-any.whl

stc8isp/__init__.py

@@ -0,0 +1 @@
+from .stc8isp import _main

stc8isp/stc8isp.py

@@ -0,0 +1,503 @@
+#!/usr/bin/env python3
+# ===================================================================================
+# Project:   stc8isp - Programming Tool for STC8G/8H Microcontrollers
+# Version:   v0.3
+# Year:      2023
+# Author:    Stefan Wagner
+# Github:    https://github.com/wagiminator
+# License:   MIT License
+# ===================================================================================
+#
+# Description:
+# ------------
+# Simple Python tool for flashing STC8G/8H microcontrollers via USB-to-serial 
+# converter utilizing the factory built-in embedded boot loader.
+# !!! THIS TOOL IS IN AN EARLY STAGE OF DEVELOPMENT !!!
+#
+# Dependencies:
+# -------------
+# - pyserial
+#
+# Operating Instructions:
+# -----------------------
+# You need to install PySerial to use stc8isp.
+# Install it via "python3 -m pip install pyserial".
+# You may need to install a driver for your USB-to-serial converter.
+#
+# Connect your USB-to-serial converter to your MCU:
+# USB2SERIAL         STC8G/8H
+#        VCC --/ --> VCC        interruptible (for power cycle)
+#        RXD --|R|-- P3.1       resistor (100R - 1000R)
+#        TXD --|<|-- P3.0       diode (e.g. 1N5819)
+#        GND ------- GND        common ground
+#
+# Run "python3 stc8isp.py -p /dev/ttyUSB0 -t 24000000 -f firmware.bin".
+# Perform a power cycle of your MCU (reconnect to power) when prompted.
+
+
+# ===================================================================================
+# Software Settings
+# ===================================================================================
+
+# If the PID/VID of the USB-to-Serial converter is known, it can be defined here.
+# The specified COM port is then ignored, and all ports are automatically searched 
+# for the device. Comment the lines to ignore PID/VID.
+#STC_VID = '1A86'
+#STC_PID = '7523'
+
+# Define the default COM port here. This will be used if no VID/PID is defined and
+# no COM port is specified within the command line arguments.
+STC_PORT = '/dev/ttyUSB0'
+
+# Define the default BAUD rates here. The minimum BAUD rate is used to calibrate the 
+# oscillator and should be low to achieve higher accuracy. The maximum BAUD rate is 
+# used to transfer the firmware and should be high to achieve higher speed.
+STC_BAUD_MIN = 2400
+STC_BAUD_MAX = 115200
+
+# Define time to wait for power cycle in seconds, default: 10
+STC_WAIT = 10
+
+# Define minimum and maximum IRC frequency in Hz, that can be specified by the
+# respective command line argument. Expanding the limit values can lead to problems!
+STC_FCPU_MIN =   128000
+STC_FCPU_MAX = 36000000
+
+# ===================================================================================
+# Libraries
+# ===================================================================================
+
+# Libraries
+import sys
+import time
+import argparse
+import serial
+from serial import Serial
+from serial.tools.list_ports import comports
+
+# ===================================================================================
+# Main Function
+# ===================================================================================
+
+def _main():
+    # Parse command line arguments
+    parser = argparse.ArgumentParser(description='Minimal command line interface for stc8isp')
+    parser.add_argument('-p', '--port',  default=STC_PORT, help='set COM port')
+    parser.add_argument('-t', '--trim',  help='trim IRC to frequency in Hz')
+    parser.add_argument('-e', '--erase', action='store_true', help='perform chip erase (implied with -f)')
+    parser.add_argument('-f', '--flash', help='write BIN file to flash')
+    args = parser.parse_args(sys.argv[1:])
+
+    # Checking command line arguments
+    if (args.trim is not None) and (int(args.trim) < STC_FCPU_MIN or int(args.trim) > STC_FCPU_MAX):
+        sys.stderr.write('ERROR: Trim value out of range (%d - %d)!\n' % (STC_FCPU_MIN, STC_FCPU_MAX))
+        sys.exit(1)
+
+    # Establish connection to USB-to-serial converter
+    try:
+        print('Connecting to USB-to-serial converter ...')
+        isp = Programmer(args.port)
+        print('SUCCESS: Connected via', isp.port + '.')
+    except Exception as ex:
+        sys.stderr.write('ERROR: ' + str(ex) + '!\n')
+        sys.exit(1)
+
+    # Performing actions
+    try:
+        # Connect to and identify MCU
+        print('Waiting for MCU power cycle ...')
+        isp.connect()
+        print('SUCCESS: Found %s v%s @ %s.' % (isp.chipname, isp.chipverstr, isp.foscstr))
+
+        # Calibrate user IRC oscillator frequency
+        if args.trim is not None:
+            print('Calibrating user IRC frequency to %s Hz ...' % args.trim)
+            isp.trim(int(args.trim))
+            print('SUCCESS: Trimmed to %d Hz (error %.2f%%).' % (isp.osc_freq, 100 * isp.osc_error))
+
+        # Switch BAUD rate
+        print('Switching BAUD rate ...')
+        isp.setbaud(STC_BAUD_MAX)
+        print('SUCCESS: BAUD rate set to %d.' % STC_BAUD_MAX)
+
+        # Perform chip erase
+        if (args.erase) or (args.flash is not None) or (args.trim is not None):
+            print('Performing chip erase ...')
+            isp.erase()
+            print('SUCCESS: Chip is erased.')
+
+        # Flash binary file
+        if args.flash is not None:
+            print('Flashing %s to MCU ...' % args.flash)
+            with open(args.flash, 'rb') as f: data = f.read()
+            isp.writeflash(0, data)
+            print('SUCCESS: %d bytes written.' % len(data))
+
+        # Write option bytes
+        if args.trim is not None:
+            print('Writing option bytes ...')
+            isp.writeoptions()
+            print('SUCCESS: Option bytes written.')
+
+        # Close connection
+        isp.disconnect()
+
+    except Exception as ex:
+        sys.stderr.write('ERROR: ' + str(ex) + '!\n')
+        isp.close()
+        sys.exit(1)
+
+    print('DONE.')
+    sys.exit(0)
+
+# ===================================================================================
+# Programmer Class
+# ===================================================================================
+
+class Programmer(Serial):
+    def __init__(self, port=STC_PORT, baud=STC_BAUD_MIN):
+        # Data frame: 1 start bit, 8 data bit, 1 parity bit set to even, 1 stop bit
+        super().__init__(baudrate = baud, parity = serial.PARITY_EVEN, timeout = 0.01)
+
+        # Use COM port to define device
+        if 'STC_VID' not in globals() or 'STC_PID' not in globals():
+            self.port = port
+
+        # Use VID/PID to find device
+        else:
+            for p in comports():
+                if (STC_VID in p.hwid) and (STC_PID in p.hwid):
+                    self.port = p.device
+                    break
+
+        # Open connection
+        try:
+            self.open()
+        except:
+            raise Exception('Failed to connect to USB-to-serial converter')
+
+    #--------------------------------------------------------------------------------
+
+    # Transmit data block
+    def transmit(self, data):
+        size   = len(data) + 6
+        parity = STC_TX_CODE + (size >> 8) + (size & 0xff)
+        for x in range(len(data)):
+            parity += data[x]
+        block  = [STC_PREFIX, STC_PREFIX ^ 0xff, STC_TX_CODE]
+        block += size.to_bytes(2, byteorder='big')
+        block += data
+        block += parity.to_bytes(2, byteorder='big')
+        block += [STC_SUFFIX]
+        self.write(block)
+
+    # Receive and check data block
+    def receive(self):
+        reply = self.read(1)
+        if len(reply) == 0 or reply[0] != STC_PREFIX:
+            return None
+        self.timeout = 1
+        reply = self.read(2)
+        if len(reply) != 2 or reply[0] != (STC_PREFIX ^ 0xff) or reply[1] != STC_RX_CODE:
+            raise Exception('Invalid data prefix from MCU')
+        size = int.from_bytes(self.read(2), byteorder='big')
+        if size < 7:
+            raise Exception('Invalid data size from MCU')
+        data = self.read(size - 6)
+        if len(data) != size - 6:
+            raise Exception('Missing data from MCU')
+        check  = int.from_bytes(self.read(2), byteorder='big')
+        suffix = self.read(1)[0]
+        if suffix != STC_SUFFIX:
+            raise Exception('Invalid data suffix from MCU')
+        parity = STC_RX_CODE + (size >> 8) + (size & 0xff)
+        for x in range(len(data)):
+            parity += data[x]
+        if (parity & 0xffff) != check:
+            raise Exception('Invalid data checksum from MCU')
+        return data
+
+    # Repeat sending sync character until reply or timeout
+    def pulse(self, char, pulsetime=0.01, timeout=10):
+        counter = timeout
+        while self.in_waiting == 0:
+            self.write([char])
+            time.sleep(pulsetime)
+            counter -= pulsetime
+            if counter <= 0:
+                raise Exception('Timout waiting for response')
+
+    #--------------------------------------------------------------------------------
+
+    # Connect to and identify MCU
+    def connect(self):
+        # Ping MCU, wait for power cycle, read info bytes
+        self.reset_input_buffer()
+        waitcounter = STC_WAIT * 100
+        reply = None
+        while (waitcounter > 0) and (reply is None):
+            self.write([STC_CHAR_SYNC])
+            reply = self.receive()
+            waitcounter -= 1
+        if waitcounter == 0:
+            raise Exception('Timeout, failed to connect to MCU')
+        if reply is None or len(reply) < 42 or reply[0] != STC_RPL_INFO:
+            raise Exception('Invalid response from MCU')
+
+        # Get chip ID
+        self.chipid = int.from_bytes(reply[20:22], byteorder='big')
+        
+        # Find chip in dictionary
+        self.device = None
+        for d in DEVICES:
+            if d['id'] == self.chipid:
+                self.device = d
+        if self.device is None:
+            raise Exception('Unsupported chip (ID: 0x%04x)' % self.chipid)
+        self.chipname   = self.device['name']
+        self.flash_size = self.device['flash_size']
+
+        # Get chip version
+        self.chipversion  = reply[17]
+        self.chipverstr   = '%d.%d.%d%c' % (reply[17] >> 4, reply[17] & 0x0f, \
+                                            reply[22] & 0x0f, reply[18])
+
+        # Get ISP-IRC and USER-IRC oscillator frequencies
+        self.fisp = int.from_bytes(reply[13:15], byteorder='big') * self.baudrate
+        self.fosc = int.from_bytes(reply[1:5], byteorder='big')
+        if self.fosc == 0xffffffff:
+            self.foscstr = 'untrimmed frequency'
+        else:
+            self.foscstr = str(self.fosc) + ' Hz'
+
+        # Get option bytes
+        self.options = reply[9:12] + reply[15:17]
+
+    # Disconnect from MCU and USB-to-serial converter
+    def disconnect(self):
+        self.transmit([STC_CMD_EXIT])
+        self.close()
+
+    #--------------------------------------------------------------------------------
+
+    # Set and calibrate USER-IRC oscillator frequency
+    def trim(self, freq):
+        # Get global trim values
+        self.transmit(STC_BLOCK_TRIM)
+        self.pulse(STC_CHAR_TRIM)
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_TRIM:
+                raise Exception('Invalid responde from MCU')
+
+        # Calculate mean trim value for specified frequency
+        freq1 = int.from_bytes(reply[ 2: 4], byteorder='big') * self.baudrate
+        freq2 = int.from_bytes(reply[ 4: 6], byteorder='big') * self.baudrate
+        freq3 = int.from_bytes(reply[ 6: 8], byteorder='big') * self.baudrate
+        freq4 = int.from_bytes(reply[ 8:10], byteorder='big') * self.baudrate
+        freq5 = int.from_bytes(reply[10:12], byteorder='big') * self.baudrate
+        self.osc_div = 1
+        while freq * self.osc_div < freq1: self.osc_div += 1
+        if freq * self.osc_div < freq5:
+            self.osc_trimx = round( (freq * self.osc_div - freq1) * 
+                (STC_BLOCK_TRIM[4] - STC_BLOCK_TRIM[2]) / (freq2 - freq1) + STC_BLOCK_TRIM[2] )
+            self.osc_bandx = STC_BLOCK_TRIM[3]
+        else:
+            self.osc_trimx = round( (freq * self.osc_div - freq3) * 
+                (STC_BLOCK_TRIM[8] - STC_BLOCK_TRIM[6]) / (freq4 - freq3) + STC_BLOCK_TRIM[2] )
+            self.osc_bandx = STC_BLOCK_TRIM[7]
+
+        # Get fine tuned trim values for specified frequency
+        count = 24
+        block = [0x00, count]
+        for x in range(count):
+            block += [self.osc_trimx - 2 + (x>>2), self.osc_bandx + (x & 0x03)]
+        self.transmit(block)
+        self.pulse(STC_CHAR_TRIM)
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_TRIM:
+                raise Exception('Invalid responde from MCU')
+
+        # Find optimal trim value
+        best = sys.maxsize
+        for x in range(count):
+            freq1 = int.from_bytes(reply[2*x+2:2*x+4], byteorder='big') * self.baudrate
+            if abs(freq * self.osc_div - freq1) < best:
+                best = abs(freq * self.osc_div - freq1)
+                self.osc_freq  = round(freq1 / self.osc_div)
+                self.osc_trim  = self.osc_trimx - 2 + (x>>2)
+                self.osc_band  = self.osc_bandx + (x & 0x03)
+                self.osc_error = (self.osc_freq - freq) / freq
+
+    # Set/switch BAUD rate
+    def setbaud(self, baud=STC_BAUD_MAX):
+        # Set BAUD rate
+        count  = round(65536 - (self.fisp / (4 * baud)))
+        block  = [STC_CMD_BAUD_SET, self.fosc & 0xff, 0x40]
+        block += count.to_bytes(2, byteorder='big')
+        block += [0x00, 0x00, 0x97]
+        self.transmit(block)
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_BAUD_SET:
+            raise Exception('Failed to set BAUD rate')
+        self.baudrate = baud
+        time.sleep(0.01)
+
+        # Check BAUD rate
+        if self.chipversion < 0x72:
+            self.transmit([STC_CMD_BAUD_CHECK])
+        else:
+            self.transmit([STC_CMD_BAUD_CHECK, 0, 0, STC_BREAK, STC_BREAK ^ 0xff])
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_BAUD_CHECK:
+            raise Exception('Failed to check BAUD rate')
+
+    #--------------------------------------------------------------------------------
+
+    # Erase flash
+    def erase(self):
+        self.transmit([STC_CMD_ERASE, 0, 0, STC_BREAK, STC_BREAK ^ 0xff])
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_ERASE:
+            raise Exception('Failed to erase flash')
+
+    # Write data to flash
+    def writeflash(self, addr, data):
+        size = len(data)
+        if size > (self.flash_size - addr):
+            raise Exception('Not enough memory')
+        cmd = STC_CMD_WRITE
+        while size > 0:
+            blocksize = min(size, STC_PAGE_SIZE)
+            block  = [cmd]
+            block += addr.to_bytes(2, byteorder='big')
+            block += [STC_BREAK, STC_BREAK ^ 0xff]
+            block += data[:blocksize]
+            self.transmit(block)
+            reply = self.receive()
+            if reply is None or reply[0] != STC_CMD_WRITE_CONT:
+                raise Exception('Failed to write to address 0x%04x' % addr)
+            cmd   = STC_CMD_WRITE_CONT
+            data  = data[blocksize:]
+            addr += blocksize
+            size -= blocksize
+
+    # Write option bytes
+    def writeoptions(self):
+        block  = [STC_CMD_OPTIONS, 0, 0, STC_BREAK, STC_BREAK ^ 0xff]
+        block += STC_BLOCK_OPTIONS1
+        block += self.osc_freq.to_bytes(4, byteorder='big')
+        block += [self.osc_trim, self.osc_band, self.osc_div]
+        block += STC_BLOCK_OPTIONS2
+        self.transmit(block)
+        reply = self.receive()
+        if reply is None or reply[0] != STC_CMD_OPTIONS:
+            raise Exception('Failed to write option bytes')
+               
+# ===================================================================================
+# Device Constants
+# ===================================================================================
+
+STC_PAGE_SIZE      = 128
+
+STC_CHAR_SYNC      = 0x7f
+STC_CHAR_TRIM      = 0x66
+
+STC_PREFIX         = 0x46
+STC_BREAK          = 0x5a
+STC_SUFFIX         = 0x16
+STC_TX_CODE        = 0x6a
+STC_RX_CODE        = 0x68
+STC_RPL_INFO       = 0x50
+
+STC_CMD_TRIM       = 0x00
+STC_CMD_BAUD_SET   = 0x01
+STC_CMD_BAUD_CHECK = 0x05
+STC_CMD_ERASE      = 0x03
+STC_CMD_OPTIONS    = 0x04
+STC_CMD_WRITE      = 0x22
+STC_CMD_WRITE_CONT = 0x02
+STC_CMD_EXIT       = 0xff
+
+STC_BLOCK_TRIM     = [0x00, 0x05, 0x02, 0x00, 0x80, 0x00, 0x00, 0x80, 
+                      0x80, 0x80, 0xfd, 0x00]
+STC_BLOCK_OPTIONS1 = [0xff, 0xff, 0xff, 0x00, 0xff, 0xff, 0x00, 0xff, 
+                      0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 
+                      0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x00, 0xff]
+STC_BLOCK_OPTIONS2 = [0xff, 0xff, 0xff, 0xff, 0xff, 0xbf, 0xbf, 0xf7, 0xff]
+
+# ===================================================================================
+# Device Dictionary
+# ===================================================================================
+
+DEVICES = [
+    {'name': 'STC8H1K16',        'id': 0xF721, 'flash_size':  16384},
+    {'name': 'STC8H1K20',        'id': 0xF722, 'flash_size':  20480},
+    {'name': 'STC8H1K24',        'id': 0xF723, 'flash_size':  24576},
+    {'name': 'STC8H1K28',        'id': 0xF724, 'flash_size':  28672},
+    {'name': 'STC8H1K33',        'id': 0xF725, 'flash_size':  33792},
+    {'name': 'STC8H1K02',        'id': 0xF731, 'flash_size':   2048},
+    {'name': 'STC8H1K04',        'id': 0xF732, 'flash_size':   4096},
+    {'name': 'STC8H1K06',        'id': 0xF733, 'flash_size':   6144},
+    {'name': 'STC8H1K08',        'id': 0xF734, 'flash_size':   8192},
+    {'name': 'STC8H1K10',        'id': 0xF735, 'flash_size':  10240},
+    {'name': 'STC8H1K12',        'id': 0xF736, 'flash_size':  12288},
+    {'name': 'STC8H1K17',        'id': 0xF737, 'flash_size':  17408},
+    {'name': 'STC8H3K16S4',      'id': 0xF741, 'flash_size':  16384},
+    {'name': 'STC8H3K32S4',      'id': 0xF742, 'flash_size':  32768},
+    {'name': 'STC8H3K60S4',      'id': 0xF743, 'flash_size':  61440},
+    {'name': 'STC8H3K64S4',      'id': 0xF744, 'flash_size':  65024},
+    {'name': 'STC8H3K48S4',      'id': 0xF745, 'flash_size':  49152},
+    {'name': 'STC8H3K16S2',      'id': 0xF749, 'flash_size':  16384},
+    {'name': 'STC8H3K32S2',      'id': 0xF74A, 'flash_size':  32768},
+    {'name': 'STC8H3K60S2',      'id': 0xF74B, 'flash_size':  61440},
+    {'name': 'STC8H3K64S2',      'id': 0xF74C, 'flash_size':  65024},
+    {'name': 'STC8H3K48S2',      'id': 0xF74D, 'flash_size':  49152},
+    {'name': 'STC8G1K02-20/16P', 'id': 0xF751, 'flash_size':   2048},
+    {'name': 'STC8G1K04-20/16P', 'id': 0xF752, 'flash_size':   4096},
+    {'name': 'STC8G1K06-20/16P', 'id': 0xF753, 'flash_size':   6144},
+    {'name': 'STC8G1K08-20/16P', 'id': 0xF754, 'flash_size':   8192},
+    {'name': 'STC8G1K10-20/16P', 'id': 0xF755, 'flash_size':  10240},
+    {'name': 'STC8G1K12-20/16P', 'id': 0xF756, 'flash_size':  12288},
+    {'name': 'STC8G1K17-20/16P', 'id': 0xF757, 'flash_size':  17408},
+    {'name': 'STC8G2K16S4',      'id': 0xF761, 'flash_size':  16384},
+    {'name': 'STC8G2K32S4',      'id': 0xF762, 'flash_size':  32768},
+    {'name': 'STC8G2K60S4',      'id': 0xF763, 'flash_size':  61440},
+    {'name': 'STC8G2K64S4',      'id': 0xF764, 'flash_size':  65024},
+    {'name': 'STC8G2K48S4',      'id': 0xF765, 'flash_size':  49152},
+    {'name': 'STC8G2K16S2',      'id': 0xF769, 'flash_size':  16384},
+    {'name': 'STC8G2K32S2',      'id': 0xF76A, 'flash_size':  32768},
+    {'name': 'STC8G2K60S2',      'id': 0xF76B, 'flash_size':  61440},
+    {'name': 'STC8G2K64S2',      'id': 0xF76C, 'flash_size':  65024},
+    {'name': 'STC8G2K48S2',      'id': 0xF76D, 'flash_size':  49152},
+    {'name': 'STC8G1K02T',       'id': 0xF771, 'flash_size':   2048},
+    {'name': 'STC8G1K04T',       'id': 0xF772, 'flash_size':   4096},
+    {'name': 'STC8G1K06T',       'id': 0xF773, 'flash_size':   6144},
+    {'name': 'STC8G1K08T',       'id': 0xF774, 'flash_size':   8192},
+    {'name': 'STC8G1K10T',       'id': 0xF775, 'flash_size':  10240},
+    {'name': 'STC8G1K12T',       'id': 0xF776, 'flash_size':  12288},
+    {'name': 'STC8G1K17T',       'id': 0xF777, 'flash_size':  17408},
+    {'name': 'STC8H8K16U',       'id': 0xF781, 'flash_size':  16384},
+    {'name': 'STC8H8K32U',       'id': 0xF782, 'flash_size':  32768},
+    {'name': 'STC8H8K60U',       'id': 0xF783, 'flash_size':  61440},
+    {'name': 'STC8H8K64U',       'id': 0xF784, 'flash_size':  65024},
+    {'name': 'STC8H8K48U',       'id': 0xF785, 'flash_size':  49152},
+    {'name': 'STC8G1K02A-8P',    'id': 0xF791, 'flash_size':   2048},
+    {'name': 'STC8G1K04A-8P',    'id': 0xF792, 'flash_size':   4096},
+    {'name': 'STC8G1K06A-8P',    'id': 0xF793, 'flash_size':   6144},
+    {'name': 'STC8G1K08A-8P',    'id': 0xF794, 'flash_size':   8192},
+    {'name': 'STC8G1K10A-8P',    'id': 0xF795, 'flash_size':  10240},
+    {'name': 'STC8G1K12A-8P',    'id': 0xF796, 'flash_size':  12288},
+    {'name': 'STC8G1K17A-8P',    'id': 0xF797, 'flash_size':  17408},
+    {'name': 'STC8G1K02-8P',     'id': 0xF7A1, 'flash_size':   2048},
+    {'name': 'STC8G1K04-8P',     'id': 0xF7A2, 'flash_size':   4096},
+    {'name': 'STC8G1K06-8P',     'id': 0xF7A3, 'flash_size':   6144},
+    {'name': 'STC8G1K08-8P',     'id': 0xF7A4, 'flash_size':   8192},
+    {'name': 'STC8G1K10-8P',     'id': 0xF7A5, 'flash_size':  10240},
+    {'name': 'STC8G1K12-8P',     'id': 0xF7A6, 'flash_size':  12288},
+    {'name': 'STC8G1K17-8P',     'id': 0xF7A7, 'flash_size':  17408}
+]
+
+# ===================================================================================
+
+if __name__ == "__main__":
+    _main()

stc8isp-0.3.0.dist-info/LICENSE

@@ -0,0 +1,21 @@
+MIT License
+
+Copyright (c) 2023 Stefan Wagner
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.

stc8isp-0.3.0.dist-info/METADATA

@@ -0,0 +1,96 @@
+Metadata-Version: 2.1
+Name: stc8isp
+Version: 0.3.0
+Summary: Programming Tool for STC8G/8H Microcontrollers
+Home-page: https://github.com/wagiminator/MCU-Flash-Tools
+Author: Stefan Wagner
+Author-email: Stefan Wagner <wagiminator@web.de>
+Maintainer-email: Stefan Wagner <wagiminator@web.de>
+License: MIT License
+        
+        Copyright (c) 2023 Stefan Wagner
+        
+        Permission is hereby granted, free of charge, to any person obtaining a copy
+        of this software and associated documentation files (the "Software"), to deal
+        in the Software without restriction, including without limitation the rights
+        to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+        copies of the Software, and to permit persons to whom the Software is
+        furnished to do so, subject to the following conditions:
+        
+        The above copyright notice and this permission notice shall be included in all
+        copies or substantial portions of the Software.
+        
+        THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+        IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+        FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+        AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+        LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+        OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+        SOFTWARE.
+Project-URL: Homepage, https://wagiminator.github.io/
+Project-URL: Repository, https://github.com/wagiminator/MCU-Flash-Tools
+Project-URL: Issues, https://github.com/wagiminator/MCU-Flash-Tools/issues
+Keywords: STC,STC8,STC8G,STC8H,microcontroller
+Classifier: Development Status :: 4 - Beta
+Classifier: Programming Language :: Python :: 3
+Classifier: License :: OSI Approved :: MIT License
+Classifier: Operating System :: OS Independent
+Classifier: Intended Audience :: Developers
+Classifier: Topic :: Software Development :: Embedded Systems
+Requires-Python: >=3.8
+Description-Content-Type: text/markdown
+License-File: LICENSE
+Requires-Dist: pyserial
+
+#  stc8isp - Programming Tool for STC8G/8H Microcontrollers
+## Description
+With this tool, STC8G/8H microcontrollers can be flashed via a simple USB-to-serial converter by utilizing the factory built-in embedded bootloader.
+
+## Preparations
+If necessary, a driver for the USB-to-serial converter used must be installed.
+
+## Installation
+- Install [Python3](https://www.pythontutorial.net/getting-started/install-python/).
+- Install [pip](https://pip.pypa.io/en/stable/installation/).
+- Install stc8isp: 
+
+```
+pip install stc8isp
+```
+
+## Usage
+- Connect your USB-to-serial converter to your MCU as shown below.
+- Run stc8isp.py (see below for arguments).
+- Perform a power cycle of your MCU (reconnect to power) when prompted.
+
+```
+USB2SERIAL         STC8G/8H
++--------+         +------+
+|     VCC| --/ --> |VCC   |    interruptible (for power cycle)
+|     RXD| --|R|-- |P3.1  |    resistor (100R - 1000R)
+|     TXD| --|<|-- |P3.0  |    diode (e.g. 1N5819)
+|     GND| ------- |GND   |    common ground
++--------+         +------+
+```
+
+```
+Usage: stc8isp [-h] [-p PORT] [-t TRIM] [-e] [-f FLASH]
+
+Optional arguments:
+  -h,       --help          show this help message and exit
+  -p PORT,  --port PORT     set COM port (default: /dev/ttyUSB0)
+  -t TRIM,  --trim TRIM     trim IRC to frequency in Hz (128000 - 36000000)
+  -e,       --erase         perform chip erase (implied with -f)
+  -f FLASH, --flash FLASH   write BIN file to flash
+
+Example:
+stc8isp -p /dev/ttyUSB0 -t 24000000 -f firmware.bin
+```
+
+## Links
+- [MCU Flash Tools](https://github.com/wagiminator/MCU-Flash-Tools)
+- [MCU Templates](https://github.com/wagiminator/MCU-Templates)
+- [MCU Development Boards](https://github.com/wagiminator/Development-Boards)
+- [AVR Development Boards](https://github.com/wagiminator/AVR-Development-Boards)
+- [AVR Programmers](https://github.com/wagiminator/AVR-Programmer)
+- [SAMD Development Boards](https://github.com/wagiminator/SAMD-Development-Boards)

stc8isp-0.3.0.dist-info/RECORD

@@ -0,0 +1,8 @@
+stc8isp/__init__.py,sha256=XKv8l5d8-9NePOt0aG6XrBkYhrYiLMvyruNlTw2mw_E,27
+stc8isp/stc8isp.py,sha256=YR_bE0-WgRHF6MLzruyhIQ89EmCtRF6gGAnxWd4Fj24,22004
+stc8isp-0.3.0.dist-info/LICENSE,sha256=kph2e2d1k_-VvrU6YbwdbUJ2GKXsFgBGCSym5wVv2j8,1089
+stc8isp-0.3.0.dist-info/METADATA,sha256=N7rMwy4AeyFlc8WH_nUCjjtF5pJ4uRH9eXdxxIYVTg0,4133
+stc8isp-0.3.0.dist-info/WHEEL,sha256=R0nc6qTxuoLk7ShA2_Y-UWkN8ZdfDBG2B6Eqpz2WXbs,91
+stc8isp-0.3.0.dist-info/entry_points.txt,sha256=ap6OJ7WEYqcNXaPwz_V44AFiiZaPStMRjOIHWIvSA3s,42
+stc8isp-0.3.0.dist-info/top_level.txt,sha256=ISZeYRachG8dOJ63E9Ngjv1gmBusWdtnyXXYrPv0XnA,8
+stc8isp-0.3.0.dist-info/RECORD,,

stc8isp-0.3.0.dist-info/WHEEL

@@ -0,0 +1,5 @@
+Wheel-Version: 1.0
+Generator: setuptools (72.1.0)
+Root-Is-Purelib: true
+Tag: py3-none-any
+

stc8isp-0.3.0.dist-info/entry_points.txt

@@ -0,0 +1,2 @@
+[console_scripts]
+stc8isp = stc8isp:_main

stc8isp-0.3.0.dist-info/top_level.txt

@@ -0,0 +1 @@
+stc8isp