quarchpy 2.2.10.dev1__py2.py3-none-any.whl → 2.2.12__py2.py3-none-any.whl

quarchpy/config_files/Drive_Modules/QTL2805-xx - Gen5 MCIO to U.2 Breaker +Triggering v5.003.qfg

@@ -1,253 +1,253 @@
-@CONFIG Version=1
-
-@HEADER
-DeviceClass=TorridonModule
-
-# Choose one of the two device numbers
-# DeviceNumbers=QTL2804-xx
-DeviceNumbers=QTL2805-xx
-
-DeviceNumbersExclude=
-MinFirmwareRequired=5.003
-MinFpgaRequired=1.2
-
-# Choose one of the two device names
-# DeviceDescription=GEN5 MCIO x4 to U.2 Breaker
-DeviceDescription=GEN5 MCIO x4 to U.2 Breaker +Triggering
-
-#Describes general module abilities
-@GENERAL
-HotPlugRead_Present = true
-GlitchStateRead_Present = true
-SourceUserBounce_Present = true
-
-# Choose one of the two triggering options
-# Triggering_Present=false
-Triggering_Present=true
-
-PowerInjection_Present=true
-SignalDrive_Present=true
-# The host power triggers actually refer to the outputs of the comparators which are looking at the host-side supplies
-# So the following line (with 3V3_AUX_HOST) would seem to make more sense than the naming which is in common use (which is 3V3_AUX)
-# HostPowerTriggering_Present=12V_HOST,3V3_AUX_HOST
-HostPowerTriggering_Present=12V_HOST,3V3_AUX
-HighResTiming_Present=true
-BounceV2_Present=true
-SignalMonitor_Present=true
-LaneWidth_Present=4
-
-# Describes all signals on the module
-# this list needs to be in the right order!
-@SIGNALS
-Name=12V_CHARGE,GlitchEnable_Present=true,DefaultSource=2
-Name=12V_POWER,GlitchEnable_Present=true,DefaultSource=3
-Name=3V3_AUX,GlitchEnable_Present=true,DefaultSource=3
-
-Name=PERST,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
-Name=REFCLK_PL,GlitchEnable_Present=true,DefaultSource=3
-Name=REFCLK_MN,GlitchEnable_Present=true,DefaultSource=3
-
-Name=PETP0,GlitchEnable_Present=true,DefaultSource=3
-Name=PETN0,GlitchEnable_Present=true,DefaultSource=3
-Name=PERP0,GlitchEnable_Present=true,DefaultSource=3
-Name=PERN0,GlitchEnable_Present=true,DefaultSource=3
-Name=PETP1,GlitchEnable_Present=true,DefaultSource=3
-Name=PETN1,GlitchEnable_Present=true,DefaultSource=3
-Name=PERP1,GlitchEnable_Present=true,DefaultSource=3
-Name=PERN1,GlitchEnable_Present=true,DefaultSource=3
-Name=PETP2,GlitchEnable_Present=true,DefaultSource=3
-Name=PETN2,GlitchEnable_Present=true,DefaultSource=3
-Name=PERP2,GlitchEnable_Present=true,DefaultSource=3
-Name=PERN2,GlitchEnable_Present=true,DefaultSource=3
-Name=PETP3,GlitchEnable_Present=true,DefaultSource=3
-Name=PETN3,GlitchEnable_Present=true,DefaultSource=3
-Name=PERP3,GlitchEnable_Present=true,DefaultSource=3
-Name=PERN3,GlitchEnable_Present=true,DefaultSource=3
-
-Name=REFCLKB_PL,GlitchEnable_Present=true,DefaultSource=3
-Name=REFCLKB_MN,GlitchEnable_Present=true,DefaultSource=3
-Name=PERSTB,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
-
-Name=SMCLK,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
-Name=SMDAT,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
-
-Name=DUALPORTEN,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
-Name=IF_DET,GlitchEnable_Present=true,DefaultSource=1,SignalMonitor_Present=true
-Name=ACTIVITY,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
-Name=WAKE,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
-Name=PWR_DIS,GlitchEnable_Present=true,DefaultSource=2,SignalMonitor_Present=true,SignalDrive_Present=true
-Name=PRSNT,GlitchEnable_Present=true,DefaultSource=2,SignalMonitor_Present=true
-Name=HPT0,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
-Name=HPT1,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
-Name=IF_DET2,GlitchEnable_Present=true,DefaultSource=1,SignalMonitor_Present=true
-Name=RSVD,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
-
-@SIGNAL_GROUPS
-# ??? what uses these groups?  How does this correspond to what is in the PIC FW?
-# This is really for TestMonkey
-# CLI test checks that these match the FW
-# But if a signal is missing from one of these groups, TestMonkey will not fail
-# MANAGEMENT group should be added here and to FW; all SB signals not including PERST/PERSTB/SMBus/REFCLKs
-Name=ALL,Signals="12V_CHARGE,12V_POWER,3V3_AUX,PERST,REFCLK_PL,REFCLK_MN,PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1,PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3,REFCLKB_PL,REFCLKB_MN,PERSTB,SMCLK,SMDAT,DUALPORTEN,IF_DET,ACTIVITY,WAKE,PWR_DIS,PRSNT,HPT0,HPT1,IF_DET2,RSVD"
-Name=LANE0,Signals="PETP0,PETN0,PERP0,PERN0"
-Name=LANE1,Signals="PETP1,PETN1,PERP1,PERN1"
-Name=LANE2,Signals="PETP2,PETN2,PERP2,PERN2"
-Name=LANE3,Signals="PETP3,PETN3,PERP3,PERN3"
-Name=POWER,Signals="12V_POWER,12V_CHARGE,3V3_AUX"
-Name=DATA,Signals="PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1,PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3"
-Name=SMBUS,Signals="SMCLK,SMDAT"
-Name=CLK_A,Signals="REFCLK_PL,REFCLK_MN"
-Name=CLK_B,Signals="REFCLKB_PL,REFCLKB_MN"
-Name=PORT_A,Signals="PERST,REFCLK_PL,REFCLK_MN,PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1"
-Name=PORT_B,Signals="PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3,REFCLKB_PL,REFCLKB_MN,PERSTB"
-Name=DATA_A,Signals="PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1"
-Name=DATA_B,Signals="PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3"
-
-# Describes all sources on the module
-@SOURCES
-
-# Describes basic source parameters
-@SOURCE_START
-Number=0
-Type=ALWAYS_OFF
-Name=Source 0
-SourceEnable_Present=false
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=1
-Type=TIMED
-Name=Source 1
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=0ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=2
-Type=TIMED
-Name=Source 2
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=25ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=3
-Type=TIMED
-Name=Source 3
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=50ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=4
-Type=TIMED
-Name=Source 4
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=0ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=5
-Type=TIMED
-Name=Source 5
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=0ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=6
-Type=TIMED
-Name=Source 6
-SourceDelay_Limits=us,0,16777215,1
-DefaultDelay=0ms
-SourceEnable_Present=true
-
-# Describes source pin-bounce parameters
-@SOURCE_BOUNCE
-SourceBounce_Present=true
-BounceLength_Limits=us,0,16777215,1
-BouncePeriod_Limits=ns,100,1677721500,100
-BounceDuty_Limits=int,1,100,1
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=7
-Type=IMMEDIATE_CHANGE
-Name=Source 7
-SourceEnable_Present=false
-@SOURCE_END
-
-# Describes basic source parameters
-@SOURCE_START
-Number=8
-Type=ALWAYS_ON
-Name=Source 8
-SourceEnable_Present=false
-@SOURCE_END
-
-# Describes glitching module
-@GLITCH
-GlitchSignals_present=true
-GlitchSignals_Version=2
-GlitchLength_Limits=int,0,255,1
-GlitchMultiplier_Settings=50ns,500ns,5us,50us,500us,5ms,50ms,500ms
-GlitchPrbs_Settings=1:2,1:4,1:8,1:16,1:32,1:64,1:128,1:256,1:512,1:1024,1:2048,1:4096,1:8192,1:16384,1:32768,1:65536
-
-# ??? is this list correct? 5V isn't on it.  How do I know if it is in the FW?  And what it is called?
-@MEASURE
-Name=12v_charge_device,Type=Voltage,NominalValue=12000
-Name=12v_power_device,Type=Voltage,NominalValue=12000
-Name=12v_host,Type=Voltage,NominalValue=12000
-Name=3v3_aux_host,Type=Voltage,NominalValue=3300
-Name=3v3_aux_device,Type=Voltage,NominalValue=3300
-Name=1v2,Type=SelfVoltage,NominalValue=1200
-Name=3v3,Type=SelfVoltage,NominalValue=3300
-Name=-5v,Type=SelfVoltage,NominalValue=-5500
-Name=5v,Type=SelfVoltage,NominalValue=5000
+@CONFIG Version=1
+
+@HEADER
+DeviceClass=TorridonModule
+
+# Choose one of the two device numbers
+# DeviceNumbers=QTL2804-xx
+DeviceNumbers=QTL2805-xx
+
+DeviceNumbersExclude=
+MinFirmwareRequired=5.003
+MinFpgaRequired=1.2
+
+# Choose one of the two device names
+# DeviceDescription=GEN5 MCIO x4 to U.2 Breaker
+DeviceDescription=GEN5 MCIO x4 to U.2 Breaker +Triggering
+
+#Describes general module abilities
+@GENERAL
+HotPlugRead_Present = true
+GlitchStateRead_Present = true
+SourceUserBounce_Present = true
+
+# Choose one of the two triggering options
+# Triggering_Present=false
+Triggering_Present=true
+
+PowerInjection_Present=true
+SignalDrive_Present=true
+# The host power triggers actually refer to the outputs of the comparators which are looking at the host-side supplies
+# So the following line (with 3V3_AUX_HOST) would seem to make more sense than the naming which is in common use (which is 3V3_AUX)
+# HostPowerTriggering_Present=12V_HOST,3V3_AUX_HOST
+HostPowerTriggering_Present=12V_HOST,3V3_AUX
+HighResTiming_Present=true
+BounceV2_Present=true
+SignalMonitor_Present=true
+LaneWidth_Present=4
+
+# Describes all signals on the module
+# this list needs to be in the right order!
+@SIGNALS
+Name=12V_CHARGE,GlitchEnable_Present=true,DefaultSource=2
+Name=12V_POWER,GlitchEnable_Present=true,DefaultSource=3
+Name=3V3_AUX,GlitchEnable_Present=true,DefaultSource=3
+
+Name=PERST,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
+Name=REFCLK_PL,GlitchEnable_Present=true,DefaultSource=3
+Name=REFCLK_MN,GlitchEnable_Present=true,DefaultSource=3
+
+Name=PETP0,GlitchEnable_Present=true,DefaultSource=3
+Name=PETN0,GlitchEnable_Present=true,DefaultSource=3
+Name=PERP0,GlitchEnable_Present=true,DefaultSource=3
+Name=PERN0,GlitchEnable_Present=true,DefaultSource=3
+Name=PETP1,GlitchEnable_Present=true,DefaultSource=3
+Name=PETN1,GlitchEnable_Present=true,DefaultSource=3
+Name=PERP1,GlitchEnable_Present=true,DefaultSource=3
+Name=PERN1,GlitchEnable_Present=true,DefaultSource=3
+Name=PETP2,GlitchEnable_Present=true,DefaultSource=3
+Name=PETN2,GlitchEnable_Present=true,DefaultSource=3
+Name=PERP2,GlitchEnable_Present=true,DefaultSource=3
+Name=PERN2,GlitchEnable_Present=true,DefaultSource=3
+Name=PETP3,GlitchEnable_Present=true,DefaultSource=3
+Name=PETN3,GlitchEnable_Present=true,DefaultSource=3
+Name=PERP3,GlitchEnable_Present=true,DefaultSource=3
+Name=PERN3,GlitchEnable_Present=true,DefaultSource=3
+
+Name=REFCLKB_PL,GlitchEnable_Present=true,DefaultSource=3
+Name=REFCLKB_MN,GlitchEnable_Present=true,DefaultSource=3
+Name=PERSTB,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
+
+Name=SMCLK,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
+Name=SMDAT,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
+
+Name=DUALPORTEN,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
+Name=IF_DET,GlitchEnable_Present=true,DefaultSource=1,SignalMonitor_Present=true
+Name=ACTIVITY,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
+Name=WAKE,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
+Name=PWR_DIS,GlitchEnable_Present=true,DefaultSource=2,SignalMonitor_Present=true,SignalDrive_Present=true
+Name=PRSNT,GlitchEnable_Present=true,DefaultSource=2,SignalMonitor_Present=true
+Name=HPT0,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
+Name=HPT1,GlitchEnable_Present=true,DefaultSource=3,SignalDrive_Present=true,SignalMonitor_Present=true
+Name=IF_DET2,GlitchEnable_Present=true,DefaultSource=1,SignalMonitor_Present=true
+Name=RSVD,GlitchEnable_Present=true,DefaultSource=3,SignalMonitor_Present=true
+
+@SIGNAL_GROUPS
+# ??? what uses these groups?  How does this correspond to what is in the PIC FW?
+# This is really for TestMonkey
+# CLI test checks that these match the FW
+# But if a signal is missing from one of these groups, TestMonkey will not fail
+# MANAGEMENT group should be added here and to FW; all SB signals not including PERST/PERSTB/SMBus/REFCLKs
+Name=ALL,Signals="12V_CHARGE,12V_POWER,3V3_AUX,PERST,REFCLK_PL,REFCLK_MN,PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1,PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3,REFCLKB_PL,REFCLKB_MN,PERSTB,SMCLK,SMDAT,DUALPORTEN,IF_DET,ACTIVITY,WAKE,PWR_DIS,PRSNT,HPT0,HPT1,IF_DET2,RSVD"
+Name=LANE0,Signals="PETP0,PETN0,PERP0,PERN0"
+Name=LANE1,Signals="PETP1,PETN1,PERP1,PERN1"
+Name=LANE2,Signals="PETP2,PETN2,PERP2,PERN2"
+Name=LANE3,Signals="PETP3,PETN3,PERP3,PERN3"
+Name=POWER,Signals="12V_POWER,12V_CHARGE,3V3_AUX"
+Name=DATA,Signals="PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1,PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3"
+Name=SMBUS,Signals="SMCLK,SMDAT"
+Name=CLK_A,Signals="REFCLK_PL,REFCLK_MN"
+Name=CLK_B,Signals="REFCLKB_PL,REFCLKB_MN"
+Name=PORT_A,Signals="PERST,REFCLK_PL,REFCLK_MN,PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1"
+Name=PORT_B,Signals="PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3,REFCLKB_PL,REFCLKB_MN,PERSTB"
+Name=DATA_A,Signals="PETP0,PETN0,PERP0,PERN0,PETP1,PETN1,PERP1,PERN1"
+Name=DATA_B,Signals="PETP2,PETN2,PERP2,PERN2,PETP3,PETN3,PERP3,PERN3"
+
+# Describes all sources on the module
+@SOURCES
+
+# Describes basic source parameters
+@SOURCE_START
+Number=0
+Type=ALWAYS_OFF
+Name=Source 0
+SourceEnable_Present=false
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=1
+Type=TIMED
+Name=Source 1
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=0ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=2
+Type=TIMED
+Name=Source 2
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=25ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=3
+Type=TIMED
+Name=Source 3
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=50ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=4
+Type=TIMED
+Name=Source 4
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=0ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=5
+Type=TIMED
+Name=Source 5
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=0ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=6
+Type=TIMED
+Name=Source 6
+SourceDelay_Limits=us,0,16777215,1
+DefaultDelay=0ms
+SourceEnable_Present=true
+
+# Describes source pin-bounce parameters
+@SOURCE_BOUNCE
+SourceBounce_Present=true
+BounceLength_Limits=us,0,16777215,1
+BouncePeriod_Limits=ns,100,1677721500,100
+BounceDuty_Limits=int,1,100,1
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=7
+Type=IMMEDIATE_CHANGE
+Name=Source 7
+SourceEnable_Present=false
+@SOURCE_END
+
+# Describes basic source parameters
+@SOURCE_START
+Number=8
+Type=ALWAYS_ON
+Name=Source 8
+SourceEnable_Present=false
+@SOURCE_END
+
+# Describes glitching module
+@GLITCH
+GlitchSignals_present=true
+GlitchSignals_Version=2
+GlitchLength_Limits=int,0,255,1
+GlitchMultiplier_Settings=50ns,500ns,5us,50us,500us,5ms,50ms,500ms
+GlitchPrbs_Settings=1:2,1:4,1:8,1:16,1:32,1:64,1:128,1:256,1:512,1:1024,1:2048,1:4096,1:8192,1:16384,1:32768,1:65536
+
+# ??? is this list correct? 5V isn't on it.  How do I know if it is in the FW?  And what it is called?
+@MEASURE
+Name=12v_charge_device,Type=Voltage,NominalValue=12000
+Name=12v_power_device,Type=Voltage,NominalValue=12000
+Name=12v_host,Type=Voltage,NominalValue=12000
+Name=3v3_aux_host,Type=Voltage,NominalValue=3300
+Name=3v3_aux_device,Type=Voltage,NominalValue=3300
+Name=1v2,Type=SelfVoltage,NominalValue=1200
+Name=3v3,Type=SelfVoltage,NominalValue=3300
+Name=-5v,Type=SelfVoltage,NominalValue=-5500
+Name=5v,Type=SelfVoltage,NominalValue=5000